Plummer Block

For New Technology Network
corporation
Plummer Blocks
CAT. NO. 2500/E

Warranty
NTN warrants, to the original purchaser only, that the delivered product which is the subject of this sale (a) will
conform to drawings and specifications mutually established in writing as applicable to the contract, and (b) be
free from defects in material or fabrication. The duration of this warranty is one year from date of delivery. If the
buyer discovers within this period a failure of the product to conform to drawings or specifications, or a defect in
material or fabrication, it must promptly notify NTN in writing. In no event shall such notification be received by
NTN later than 13 months from the date of delivery. Within a reasonable time after such notification, NTN will, at
its option, (a) correct any failure of the product to conform to drawings, specifications or any defect in material or
workmanship, with either replacement or repair of the product, or (b) refund, in part or in whole, the purchase
price. Such replacement and repair, excluding charges for labor, is at NTN's expense. All warranty service will
be performed at service centers designated by NTN. These remedies are the purchaser's exclusive remedies
for breach of warranty.
NTN does not warrant (a) any product, components or parts not manufactured by NTN, (b) defects caused by
failure to provide a suitable installation environment for the product, (c) damage caused by use of the product for
purposes other than those for which it was designed, (d) damage caused by disasters such as fire, flood, wind,
and lightning, (e) damage caused by unauthorized attachments or modification, (f) damage during shipment, or
(g) any other abuse or misuse by the purchaser.
THE FOREGOING WARRANTIES ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
In no case shall NTN be liable for any special, incidental, or consequential damages based upon breach of
warranty, breach of contract, negligence, strict tort, or any other legal theory,and in no case shall total liability of
NTN exceed the purchase price of the part upon which such liability is based. Such damages include, but are
not limited to, loss of profits, loss of savings or revenue, loss of use of the product or any associated equipment,
cost of capital, cost of any substitute equipment, facilities or services, downtime, the claims of third parties
including customers, and injury to property. Some states do not allow limits on warranties, or on remedies for
breach in certain transactions. In such states, the limits in this paragraph and in paragraph (2) shall apply to the
extent allowable under case law and statutes in such states.
Any action for breach of warranty or any other legal theory must be commenced within 15 months following
delivery of the goods.
Unless modified in a writing signed by both parties, this agreement is understood to be the complete and
exclusive agreement between the parties, superceding all prior agreements, oral or written, and all other
communications between the parties relating to the subject matter of this agreement. No employee of NTN or
any other party is authorized to make any warranty in addition to those made in this agreement.
This agreement allocates the risks of product failure between NTN and the purchaser. This allocation is
recognized by both parties and is reflected in the price of the goods. The purchaser acknowledges that it has
read this agreement, understands it, and is bound by its terms.
NTN Corporation. 1998

Although care has been taken to assure the accuracy of the data compiled in this catalog, NTN does not
assume any liability to any company or person for errors or omissions.
CONTENTS
Technical Data 332
Split type 3451
Index of Bearing Tables
Unit type 5259
Specialized Plummer Blocks 6063

NTN
PLUMMER BLOCKS
1
CONTENTS
1. Structure 3
2. Plummer Block and Rolling Bearing Tolerances 4

2.1 Plummer block tolerances 4
2.2 Machining tolerances of mounting bolt seat faces 8
2.3 Rolling bearing accuracies9
2.4 Rolling bearing internal clearance 11
3. Plummer Block and Bearing Materials13

3.1 Plummer block materials 13
3.2 Bearing materials 14
4. Strength of Plummer Blocks, and Combination with Bearings15

4.1 Strength of plummer blocks 15
4.2 Combinations of plummer blocks and bearings 16
5. Allowable Speed18
6. Bearing Seals 19
6.1 Contact seals 19
6.2 Non-contact seals 20
6.3 Combination seals20
7. Shaft Design 21
7.1 Bearing-to-shaft fit21
7.2 Mounting dimensions 21
8. Lubrication 23
8.1 Grease lubrication 23
9. Handling the Plummer Blocks and Bearings 24

9.1 Inspection before installation 24
9.2 Preparation for installing the bearing 24
9.3 Installation of the bearing and associated components 25
9.4 Assembling the plummer blocks 29
9.5 Running inspection 30
9.6 Maintenance and inspection 31
9.7 Bearing disassembly31
9.8 Cleaning the bearing 32
9.9 Storing the bearing 32
2
Plummer Blocks
1. Structure
Tightening bolt Oil fill plug

The bolt protects the plummer block against For relubrication.
loosening due to vibration and impact.
Seal
Excellent sealing performance.
Self-aligning rolling bearing

Self-aligning ball or roller bearing is
built into plummer block.
Adapter
Simplifies installation
of the bearing.
Mounting bolt holes

Oil drain plug Allow easy positioning
For draining old lubricant. and installation.
Plummer block unit Knock ball

Designed for greater mechanical strength, and manufactured The upper and lower housings can be assembled
under strict quality control program. To suit the intended together at higher accuracy thanks to ball-knock
application, it can be made of either spheroidal graphite cast iron system using steel balls. Also, the upper cover
(ductile cast iron) or cast steel. can be installed or removed easily.
Products painted in user-specified colors s
3
Plummer Block and Rolling Bearing Tolerances
2. Plummer Block and Rolling Bearing Tolerances
2.1 Plummer block tolerances

The tolerances of NTN split plummer blocks meet JIS B 1551, and those of unit type plummer blocks with Japan Bearing
Manufacturers' Association standard BAS 188. The tolerances of both types are given in the tables below.
Tolerances of bearing seating bore diameter, width and center height Table 2.1
Tolerances of length of cast iron components
(As cast portions on bearing base, bolt holes, etc.) Table 2.2
Dimensions and tolerances of bore Table 2.3
Dimensions and tolerances of stabilizing ring Table 2.4
Table 2.1 Tolerances of plummer blocks Unit: mm

Split type Unit type
Housing Housing Center Housing Center Body Cover Cover
Plummer block series bore width height Plummer block bore height width dimensions spigot
diameter series diameter width
Ds gs Hs Ds Hs I1 I2 I3
SN5, SN5F
SN (S)6, SN (S)6F
SN2, SNZ2, SN30
H8 H13 h13
SN (S)3, SNZ (SZ)3, SN31 SV5
SAF5, SAF6 SV6
SBG5 SV2
SV3 H7 h11 0.2 1 0
SD30, SD31 SV30 0 0.2
SD33 SV35
SD34, SD35 VA5
SD36 H8 0.2 h13
SD2, SD3
SD5, SD6
SD31TS, SD32TS
Table 2.2 Tolerances of length of cast iron components Unit: mm

Casting size
120 or less 120 to 250 250 to 400 400 to 800 800 to 1600
1.5 2.0 3.0 4.0 6.0
4
Table 2.3 Bore dimensions and tolerances

Unit: mm
Shaft
d2 d3 f1 f2 Rubber seal
diameter Angular part number
tolerance (reference)
d1 Dimension Tolerance Dimension Tolerance Dimension Tolerance Dimension
0.140
20 21.5 0.210 31 3 0 4.2 ZF 5
25 26.5 0 38 0.250 4 5.4 ZF 6
30 31.5 43 0 4 5.4 ZF 7
35 36.5 0.250 48 4 5.4 ZF 8
40 41.5 0 53 4 5.4 ZF 9
45 46.5 58 4 5.4 ZF10
0.300
50 51.5 67 5 6.9 ZF11
0 0.180
55 56.5 82 5 6.9 ZF12
0
60 62 77 5 6.8 ZF13
0.300
65 67 0 82 5 6.8 ZF15
70 72 89 6 8.1 ZF16
75 77 94 6 8.1 ZF17
0.350
80 82 99 0 6 8.1 ZF18
85 87 104 6 8.1 ZF19
90 92 111 7 9.3 ZF20
0.350
100 102 0 125 8 10.8 ZF22
110 113 135 8 10.7 ZF24
115 118 140 8 10.7 ZF26
0.400
125 128 154 0 9 12.2 ZF28
135 138 164 9 0.220 12.2 1 ZF30
140 143 173 10 0 13.7 ZF32
0.400
150 153 0 183 10 13.7 ZF34
160 163 193 10 13.7 ZF36
170 173 203 0.460 10 13.7 ZF38
0
180 183 213 10 13.7 ZF40
200 203 0.460 240 11 15.5 ZF44
220 223 0 260 11 15.5 ZF48
0.520
240 243 286 12 17.3 ZF52
0
260 263 306 12 17.3 ZF56
280 283 0.520 332 13 19 ZF60
0
300 303 352 0.570 13 19 ZF64
320 323 372 0 13 0.27 0 19 ZF68
340 343 390 14 0 19.8 GS72
0.570
360 363 0 412 13 19 GS76
380 383 432 13 19 GS80
400 403 452 0.630 14 20 GS84
0
410 413 0.630 460 14 19.8 GS88
430 433 0 480 14 19.8 GS92
450 453 505 0.700 14 20.3 GS96
0
5
Table 2.4 (1) Dimensions and tolerances of locating rings

Unit: mm Unit: mm
Part number Outside Inside dia. Width Material Part number Outside Inside dia. Width Material
dia. dia.
0 0
h12 0.2 h12 0.2
SR 52 5 52 44 5 SR12010 120 108 10
SR 52 6 52 44 6 SR12012 120 108 12
SR 52 7 52 44 7 SR12013 120 108 13
SR 52 9 52 44 9 SR125 9.5 125 113 9.5
SR 62 6 62 54 6 SR12510 125 113 10
SR 62 6.5 62 54 6.5 SR12513 125 113 13
SR 62 7 62 54 7 SR130 4 130 118 4
SR 62 8.5 62 54 8.5 SR130 8 130 118 8
SR 6210 62 54 10 SR130 9.5 130 118 9.5
SR 72 6 72 64 6 SR13010 130 118 10
SR 72 7 72 64 7 SR13012.5 130 118 12.5
SR 72 8 72 64 8 SR140 8 140 125 8
SR 72 9 72 64 9 SR140 8.5 140 125 8.5
SR 7210 72 64 10 SR14010 140 125 10
SR 80 6 80 70 6 SR14011.5 140 125 11.5
SR 80 7 80 70 7 SR14012.5 140 125 12.5
SR 80 7.5 80 70 7.5 SR14015 140 125 15
SR 80 8 80 70 8 SR150 5 150 135 5
SR 80 9.5 80 70 9.5 SR150 9 150 135 9
SR 8010 80 70 10 SR15010 150 135 10
Die-cast Die-cast
SR 85 6 85 75 6 zinc alloy, SR15010.5 150 135 10.5 zinc alloy,
SR 85 8 85 75 8 class 2, SR15014 150 135 14 class 2,
ZDC2 ZDC2
SR 8510 85 75 10 SR15013 150 135 13
SR 90 6 90 80 6 SR160 7 160 144 7
SR 90 6.5 90 80 6.5 SR160 9.6 160 144 9.6
SR 90 8 90 80 8 SR16010 160 144 10
SR 90 9.5 90 80 9.5 SR16011 160 144 11
SR 9010 90 80 10 SR16011.2 160 144 11.2
SR100 6 100 89 6 SR16012.5 160 144 12.5
SR100 8 100 89 8 SR16014 160 144 14
SR100 8.5 100 89 8.5 SR16015 160 144 15
SR10010 100 89 10 SR16016 160 144 16
SR10010.5 100 89 10.5 SR16016.2 160 144 16.2
SR110 6 110 99 6 SR170 4 170 154 4
SR110 8 110 99 8 SR170 9.5 170 154 9.5
SR110 9 110 99 9 SR17010 170 154 10
SR110 9.5 110 99 9.5 SR17010.5 170 154 10.5
SR11010 110 99 10 SR17011.5 170 154 11.5
SR11011.5 110 99 11.5 SR17014.5 170 154 14.5
SR11012 110 99 12 SR17015 170 154 15
SR120 6 120 108 6 SR180 9.5 180 163 9.5
SR120 9 120 108 9 SR180 9.7 180 163 9.7
6
Table 2.4 (2) Dimensions and tolerances of locating rings

Unit: mm Unit: mm
Part number Outside Inside dia. Width Material Part number Outside Inside dia. Width Material
dia. dia.
0 0
h12 0.2 h12 0.2
SR18010 180 163 10 SR250 6 250 230 6
SR18012 180 163 12 SR250 9.5 250 230 9.5
SR18012.1 180 163 12.1 SR25010 250 230 10
SR18014.5 180 163 14.5 SR25013 250 230 13
SR18018 180 163 18 SR25015 250 230 15
SR18018.1 180 163 18.1 SR260 9.5 260 238 9.5
SR190 6 190 173 6 SR26010 260 238 10
SR190 9.5 190 173 9.5 SR26017 260 238 17
SR19013.5 190 173 13.5 SR270 7 270 248 7
SR19015.3 190 173 15.3 SR270 9.5 270 248 9.5
SR200 9.5 200 180 9.5 SR27010 270 248 10
SR20010 200 180 10 SR27015 270 248 15
SR20012.2 200 180 12.2 SR27016.5 270 248 16.5
SR20013.5 200 180 13.5 SR280 9.5 280 255 9.5
SR20014.5 200 180 14.5 SR28010 280 255 10
SR20015 200 180 15 SR28015 280 255 15
SR20015.8 200 180 15.8 SR290 9 290 268 9
SR20018.5 200 180 18.5 SR29010 290 268 10
SR20021 200 180 21 SR29016.5 290 268 16.5
SR20022 200 180 22 SR29017 290 268 17
Die-cast Gray cast
SR2109.5 210 190 9.5 zinc alloy, SR300 9.5 300 275 9.5 iron,
SR21010 210 190 10 class 2, SR30010 300 275 10 class 3,
ZDC2 FC200
SR215 6 215 195 6 SR30011 300 275 11
SR215 9 215 195 9 SR31010 310 290 10
SR215 9.5 215 195 9.5 SR31012 310 290 12
SR21510 215 195 10 SR31018 310 290 18
SR21512 215 195 12 SR320 9.5 320 290 9.5
SR21514 215 195 14 SR32010 320 290 10
SR21517.5 215 195 17.5 SR32014 320 290 14
SR21517.8 215 195 17.8 SR32018 320 290 18
SR225 9.5 225 205 9.5 SR340 9.5 340 310 9.5
SR22510 225 205 10 SR34010 340 310 10
SR230 6 230 210 6 SR34016 340 310 16
SR23010 230 210 10 SR34019 340 310 19
SR23011 230 210 11 SR36010 360 330 10
SR23013 230 210 13 SR38010 380 350 10
SR240 9.5 240 218 9.5 SR40010 400 370 10
SR24010 240 218 10 SR50015.5 500 470 15.5
SR24016 240 218 16 SR54018.5 540 510 18.5
SR24019.8 240 218 19.8 SR58021.5 580 550 21.5
SR24023 240 218 23
SR250 5 250 230 5
7
2.2 Machining tolerances of mounting bolt seat

faces
When subjected to a greater lateral load, a plummer block
cannot be reliably secured with the tightening force of
mounting bolts alone. To overcome this problem the end
faces of the mounting bolt seat are secured with stoppers
to lock the plummer block. With the plummer block used
in this type of application, the end faces in contact with
the stoppers are machined.
When a plummer block mounting seat end faces have
been machined, the bottom length L of the bearing
housing is smaller by the dimension in Table 2.5.
L: Basic casting dimension (as cast dimension)

Table 2.5 Machining allowance L': Dimension after machining of the end faces of bearing base
Unit: mm
Plummer block Machining Surface
part number allowance roughness
,
L-L
SN506SN519
SN206SN219
SNZ206SNZ219
SN606SN616
SN306SN316 3
SNZ306SNZ316
SV505SV519
SV205SV219
SV605SV616
SV305SV316
SN520
SN220
SNZ220
SN617
SN317
SNZ317
5
Model SN30, model SN31
Model SN..F, model SD
SV520
SV220
SV617
SV317
Table 2.6 Tolerances of dimension L after machining of

mounting bolt seat end faces Unit: mm
Dimension after
machining 30120 120315 3151 000 1 0002 000
,
L
Tolerance 0.8 1.2 2.0 3.0
8
2.3 Rolling bearing accuracies

The tolerances of self-aligning ball and roller bearings
used in conjunction with NTN plummer blocks conform to
JIS B 1514 (Tolerances for rolling bearings).
Table 2.7 Bearing tolerances

(1) Tolerances of inner rings (JIS class 0) Unit: m
Nominal Single plane Single radial plane bore Mean single Inner ring Inner ring Inner ring
bore diameter mean bore diameter variation plane bore radial runout width deviation width variation
d diameter deviation Vdp diameter deviation Kia BS VBS
dmp diameter series diameter series Vdmp
(mm) 0, 1 2, 3, 4
over incl. high low max max max max high low max
18 30 0 10 10 8 8 13 0 120 20
30 50 0 12 12 9 9 15 0 120 20
50 80 0 15 19 11 11 20 0 150 25
80 120 0 20 25 15 15 25 0 200 25
120 150 0 25 31 19 19 30 0 250 30
150 180 0 25 31 19 19 30 0 250 30
180 250 0 30 38 23 23 40 0 300 30
250 315 0 35 44 26 26 50 0 350 35
315 400 0 40 50 30 30 60 0 400 40
400 500 0 45 56 34 34 65 0 450 50
(2) Tolerances of outer rings (JIS class 0) Unit: m

Nominal outside Single plane Single radial plane outside Mean single plane Outer ring Outer ring Outer ring
diameter outside diameter diameter deviation outside diameter radial runout width deviation width variation
D deviation VDp deviation Kea Cs VCs
Dmp diameter series diameter series Vdmp
(mm) 0, 1 2, 3, 4
over incl. high low max max max max high low max
30 50 0 11 11 8 8 20
50 80 0 13 13 10 10 25 Depends on Depends on
80 120 0 15 19 11 11 35 tolerance of tolerance of
BS relative to VBS relative to
120 150 0 18 23 14 14 40
d of the same d of the same
150 180 0 25 31 19 19 45
bearing. bearing.
180 250 0 30 38 23 23 50
250 315 0 35 44 26 26 60
315 400 0 40 50 30 30 70
400 500 0 45 56 34 34 80
500 630 0 50 63 38 38 100
630 800 0 75 94 55 55 120
9
(3) Tolerance and allowable values (JIS class 0)

of tapered 1 bore radial bearings Unit: m
Nominal bore
diameter
d dmp dmp - dmp Vdp
(mm)
over incl. high low high low max
50 80 15 0 30 0 19
80 120 20 0 35 0 22
120 180 25 0 45 0 40
180 250 30 0 46 0 46
250 315 35 52 52 Theoretical tapered bore Tapered bore associated with single
0 0
315 400 40 57 57 plane mean bore diameter deviation
0 0
400 500 45 0 63 0 63
500 630 50 0 70 0 70
1 Applicable to all radial planes of tapered bore
Note 1: Applicable to 1/12 tapered bore
2: Quantifiers
d1 : Standard diameter at theoretical large end of tapered bore
1
d1 = d B
12
dmp : Single plane mean bore diameter deviation at
theoretical small end of tapered bore
d1mP : Single plane mean bore diameter deviation at
theoretical large end of tapered bore
Vdp : Bore diameter variation in a single radial plane
B : Nominal bore diameter
: 1/2 nominal taper angle of tapered bore
= 223'9.4''
= 2.38594
= 0.041643 rad
10
2.4 Rolling bearing internal clearance

The radial clearance values of the self-aligning ball
bearings used in the NTN plummer blocks are
summarized in Table 2.8 (1) and (2), and those of the
self-aligning roller bearings in Table 2.9 (1) and (2).
Table 2.8 Radial internal clearance of self-aligning ball bearings

(1) Data for cylindrical bore bearings Unit: m
Nominal bore diameter Clearance

d (mm)
C2 CN (normal) C3 C4 C5
over incl. max min max min max min max min max min
24 30 5 16 11 24 19 35 29 46 40 58
30 40 6 18 13 29 23 40 34 53 46 66
40 50 6 19 14 31 25 44 37 57 50 71
50 65 7 21 16 36 30 50 45 69 62 88
65 80 8 24 18 40 35 60 54 83 76 108
80 100 9 27 22 48 42 70 64 96 89 124
100 120 10 31 25 56 50 83 75 114 105 145
(2) Data for tapered bore bearings Unit: m

d (mm)
24 30 9 20 15 28 23 39 33 50 44 62
30 40 12 24 19 35 29 46 40 59 52 72
40 50 14 27 22 39 33 52 45 65 58 79
50 65 18 32 27 47 41 61 56 80 73 99
65 80 23 39 35 57 50 75 69 98 91 123
80 100 29 47 42 68 62 90 84 116 109 144
100 120 35 56 50 81 75 108 100 139 130 170
11
Table 2.9 Radial internal clearance of self-aligning roller bearings

(1) Data for cylindrical bore bearings Unit: m

d (mm)
30 40 15 30 30 45 45 60 60 80 80 100
40 50 20 35 35 55 55 75 75 100 100 125
50 65 20 40 40 65 65 90 90 120 120 150
65 80 30 50 50 80 80 110 110 145 145 180
80 100 35 60 60 100 100 135 135 180 180 255
100 120 40 75 75 120 120 160 160 210 210 260
120 140 50 95 95 145 145 190 190 240 240 300
140 160 60 110 110 170 170 220 220 280 280 350
160 180 65 120 120 180 180 240 240 310 310 390
180 200 70 130 130 200 200 260 260 340 340 430
200 225 80 140 140 220 220 290 290 380 380 470
225 250 90 150 150 240 240 320 320 420 420 520
250 280 100 170 170 260 260 350 350 460 460 570
280 315 110 190 190 280 280 370 370 500 500 630
315 355 120 200 200 310 310 410 410 550 550 690
355 400 130 220 220 340 340 450 450 600 600 750
400 450 140 240 240 370 370 500 500 660 660 820
450 500 140 260 260 410 410 550 550 720 720 900
(2) Data for tapered bore bearing Unit: m

d (mm)
30 40 25 35 35 50 50 65 65 85 85 105
40 50 30 45 45 60 60 80 80 100 100 130
50 65 40 55 55 75 75 95 95 120 120 160
65 80 50 70 70 95 95 120 120 150 150 200
80 100 55 80 80 110 110 140 140 180 180 230
100 120 65 100 100 135 135 170 170 220 220 280
120 140 80 120 120 160 160 200 200 260 260 330
140 160 90 130 130 180 180 230 230 300 300 380
160 180 100 140 140 200 200 260 260 340 340 430
180 200 110 160 160 220 220 290 290 370 370 470
200 225 120 180 180 250 250 320 320 410 410 520
225 250 140 200 200 270 270 350 350 450 450 570
250 280 150 220 220 300 300 390 390 490 490 620
280 315 170 240 240 330 330 430 430 540 540 680
315 355 190 270 270 360 360 470 470 590 590 740
355 400 210 300 300 400 400 520 520 650 650 820
400 450 230 330 330 440 440 570 570 720 720 910
450 500 260 370 370 490 490 630 630 790 790 1 000
12
Plummer Block and Bearing Materials
3. Plummer Block and Bearing Materials
3.1 Plummer block materials

The housings of NTN plummer blocks are made of class 3
gray cast iron (FC200). Table 3.1 summarizes the
mechanical properties of this material.
Cast iron materials boasts the greatest vibration
dampening capability among various metal materials.
They also perform well in a wider operating temperature
range of 20 to 300C.
For application involving shock load and vibration, class 2
spheroidal graphite cast iron (FCD450) or class 3 carbon
cast steel (SC450) is used.
Table 3.1 Mechanical properties

(1) Mechanical properties of gray cast iron
Type Symbol Typical wall thickness Cast diameter Tensile strength Transverse test Brinell
of cast iron product of samples hardness
Maximum load Flexure
mm mm MPa N mm HB
(kgf/mm2) (kgf)
4 to 8 13 235 {24} over 1 960 {200} over 2.0 over 255 incl.
Gray
over 8, incl. 15 20 216 {22} over 4 410 {450} over 3.0 over 235 incl.
cast iron, FC200
over 15, incl. 30 30 196 {20} over 8 820 {900} over 4.5 over 223 incl.
class 3
over 30, incl. 50 45 167 {17} over 19 600 {2 000} over 6.5 over 217 incl.
(2) Mechanical properties of spheroidal graphite cast iron
Type Symbol Tensile test Impact test
Proof stress Tensile strength Elongation Charpy absorption energy

MPa MPa % Nm
(kgf/mm2) (kgf/mm2) {kgfm}
Class 2 spheroidal
FCD450 226 {23} over 450 {46} over 10 over
graphite cast iron
(3) Mechanical properties of carbon cast steel
Type Symbol Yield point Tensile test
Tensile strength Elongation Reduction in area

MPa MPa % %
(kgf/mm2) (kgf/mm2)
Carbon cast steel SC450 226 {23} over 451 {46} over 19 over 30 over
13
Plummer Block and Bearing Materials
Table 3.2 Plummer block accessories materials
Accessory Material used Symbol Applicable JIS standard
Tightening bolt and nut Class 2 rolled steel for general structure SS400 G3101
Spring washer Hard drawn steel wire SWRH62B G3506
Grease nipple (on housing) Copper and copper alloy rod and bar C3604B H3250
Plug for relubrication or draining Class 2 rolled steel for general structure SS400 G3101
Stabilizing ring, general purpose Class 3 gray cast iron and class 2 zinc die-casting FC200, ZDC2 G5501, H5301
(normal width) Class 2 rolled steel for general structure SS400 G3101
3.2 Bearing materials

Raceway and rolling element materials
When the contact surfaces of a bearing raceway and By using pure materials, low in these non-metallic
rolling elements are repeatedly subjected to heavy stress, impurities, the rolling fatigue life of the bearing is
they still must maintain high precision and running lengthened. For all NTN bearings, pure material is
accuracy. To accomplish this, the raceway and rolling prepared which has low oxygen content and low non-
elements must be made of a material that has high metallic impurities, by vacuum degassing process and
hardness, is resistant to rolling fatigue, is wear resistant, secondary refining process.
and has good dimensional stability.
Table 3.3 Adapter materials

Applicable
Part description Material used Symbol Remarks
JIS standard
Bearing bore #14 or smaller Carbon steel for machine structural purposes STKM13A G3445 Can be SS400 (G3101), S20C to
Sleeve,
adapter S35C (G4051), STPG370 (G3454)
Bearing bore #15 or greater Carbon steel for machine structural purposes S25C G4051 or STKM13A (G3445).
#05#07 Carbon steel for machine structural purposes S20C G4051
Can be SS400 (G3101), or
Nut #08#32 Rolled steel for general structure SS400 G3101
S20C to S35C (G4051).
#34 Carbon steel for machine structural purposes S25C G4051
Thickness: less than 3 mm Cold rolled steel plate and strip SPCC-SD G3141
Lock-
washer
Thickness: 3 mm or greater Rolled steel for general structure SS400 G3101 Can be SPHD (G3131).
Lock
plate Rolled steel for general structure SS400 G3101 Can be S20C to S35C (G4051).
Cage materials
Bearing cage materials must be strong enough to
withstand the vibration and shock load occurring on
running bearings, develop limited friction with rolling
elements and bearing ring, be light, and resist the heat
occurring on running bearings.
The cages for small- and medium-sized bearings are
pressed cages prepared through pressing process with
cold or hot rolled steel plate, while the cages for large-
sized bearings are machined cages made of cast high
tensile brass or carbon steel for machine structural
purposes.
14
Strength of Plummer Blocks, and Combination with Bearings
4. Strength of Plummer Blocks, and Combination with Bearings
4.1 Strength of plummer blocks Table 4.1 Safety factors of cast iron plummer blocks
The disruptive strength of plummer block varies Nature of load Light Repeated Alternating Shock
depending on its type, nature and direction of a load Safety factor 4 6 10 15
working on it, as well as the flatness of a surface to which
it is installed. The typical trend of static disruptive strength
of SN5 and SN6 (S6) series of cast iron plummer blocks To counter a horizontal or axial load, the face
is plotted in Figs. 4.1 and 4.2 respectively. of the bed must be secured with a stopper.
When selecting a plummer block, the safety factors in For applications where extreme shock load is
Table 4.1 must be considered. Also, a higher grade of present or a fractured plummer block can lead
flatness is required of a surface for mounting a plummer to severe accident, NTN offers special plummer
block. blocks made of spherical graphite cast iron or
cast steel. For further information, contact NTN
Engineering.
Fig. 4.1 Static disruptive strength of SN5 series Fig 4.2 Static disruptive strength of SN6 (S6) series
15
4.2 Combinations of plummer blocks and bearings

The typical plummer block-bearing combinations are listed in
Tables 4.2 (1) and (2).
Table 4.2 (1) Plummer blocks and applicable bearings

Bearing series
Plummer 12 22 13 23 230 231 222 232 213 223
block series
SN5 08CK32BK 18BK
06K22K 06K22
SN5F 11EK18EK 20BK32BK
SN(S)6
06K22K 06K22K 08CK22K 08CK32BK
SN(S)6F
SN2 08C32B 18B
0622 0622
SN2F 11E18E 20B32B
SN (S) 3
0622 0622 08C22 08C32B
SN (S) 3F
SNZ2 08C32B 18B
0622 0622
SNZ2F 11E18E 22B32B
SNZ (SZ) 3
0622 0622 08C22 08C32B
SNZ (SZ) 3F
SN30 24BK38BK
SN31 22BK38BK
SD5
34BK64BK
SD5G
SD6
34BK56BK
SD6G
SD2
34B64B
SD2G
SD3
SD3G 34B56B
SD2D
34B64B
SD2DG
SD3D
34B56B
SD3DG
SD30
34BK96BK
SD30G
SD31
34BK84BK
SD31G
16
Table 4.2 (2) Plummer blocks and applicable bearings

Bearing series
Plummer 12 22 13 23 230 231 222 232 213 223
block series
08CK64BK 18B
SV5 05K22K 05K22K
11EK18EK 20B32B
SV6 05K22K 05K22K 08CK22K 08CK22K
08C32B 16BK
SV2 0522 0522
11E18E 20B64B
SV3 0522 0522 08C22 08C56B
Example of application with cylindrical roller bearing
Example of application with deep groove ball bearing
17
Allowable Speed
5. Allowable Speed
Greater bearing speed leads to higher bearing operating conditions can be determined by multiplying the
temperature owing to friction heat occurring within the allowable speed of that bearing in a bearing table by an
bearing. When the bearing is heated beyond a specific adjustment factor in Fig. 5.1.
limit, a bearing failure such as seizure occurs, and the The allowable speed of a plummer block with a bearing
bearing cannot maintain stable operation any more. The varies depending on the seal type used. For example, in
limiting bearing speed where a bearing can operate the case of a plummer block having a contact seal, its
without developing heat beyond a particular limitation is allowable speed is restricted by the allowable peripheral
called allowable speed (rpm). This varies depending on speed of the seal. Fig. 5.2 provides a guideline for
the type and size of bearing, type of cage, as well as selecting allowable peripheral speeds of various seals.
loading, lubricating and cooling conditions.
The bearing tables in this brochure summarize the
typical allowable bearing speeds either with grease or oil
lubrication. However, these values assume that:
An NTN standard design bearing having correct internal
clearance is correctly installed.
The bearing is lubricated with quality lubricant, and the
lubricant is replenished or replaced at correct intervals.
The bearing is operated under normal loading
conditions (P0.09Cr, Fa/Fr0.3), and at a normal
operating temperature.
Note, however, that rolling elements may fail to rotate
smoothly under a load of P0.04Cor. For advice against
this problem, contact NTN Engineering. Also, note that
the allowable speed of deep groove ball bearing having a
contact seal (model LLU) or low-torque seal (model LLH) Fig. 5.1 Values of adjustment factor f L dependent on bearing load
is governed by the peripheral speed of the seal. The
C: Basic dynamic load rating N
allowable speed of a bearing that is used under severe
P: Dynamic equivalent load N
Fig. 5.2 Allowable speed of bearing vs. allowable peripheral speed of seal no
1 Determine the allowable speed of the seal of a cylindrical bore bearing by referring to the shaft diameter at the contact surface of the seal.
In the plotting above, the allowable speeds of the seal are indicated as shaft speeds (rpm).
18
Bearing Seals
6. Bearing Seals
The purposes of bearing seals are to prevent lubricant

from leaking out and to protect the bearing against
ingress of dust and moisture.
An appropriate bearing seal is selected considering the
lubricant type (grease or oil) and the peripheral speed of
the seal.
The seal type of NTN plummer blocks can be either
contact or non-contact type. The contact type is available
as felt seals and rubber seals, while the non-contact type
as labyrinth seals. Also, special combination seals are
available for applications under severe operating
conditions involving, for example, heavy air-borne dust.
Fig. 6.1 Rubber seal

6.1 Contact seals
(1) Rubber seal (Fig. 6.1)
Rubber seals are typically used for grease lubrication,
and their allowable peripheral speed, as a guideline,
ranges from 5 to 6 m/s.
Usually, the material of rubber seals are nitrile rubber.
However, to cope with demanding ambient temperatures,
the materials in Table 6.1 are also available.
(2) Felt seal (Fig. 6.2)

Felt seals are compatible with rubber seals, but must be
used for grease lubrication only.
Felt seals are not suitable for dusty or moist
environments. Their allowable peripheral speed, as a
guideline, is 4 m/s max. A felt seal can be cut into two
pieces that are respectively fitted into the seal grooves on Fig. 6.2 Felt seal
the upper and lower plummer block housings. This
feature greatly simplifies the assembly procedure for
plummer blocks.
Table 6.1 Types and features of rubber seal materials

Wear resistance
Oil resistance
Acid resistance
Alkali resistance
Water resistance
C
temperature range
operating
Recommended
Seal material Features
Nitrile rubber (NBR) resists virtually all oil types and also features good wear
25 resistance. Thus, this material is most commonly used as an oil seal material.
Nitrile rubber (NBR) It can be used in ordinary machinery operating under virtually any normal
100
operating conditions.
15 Boasts excellent heat resistance and oil resistance, but is rather vulnerable
Acrylic rubber (ACM)
130 to alkali or water. Thus, the scope of its applications is limited.
50 Boasts excellent heat resistance and cold resistance. However, it cannot be

Silicone rubber (VMQ)
220 used together with extreme pressure grease or spindle oil.
Inert to virtually all oil or chemical types. Its properties are well balanced.
10 Therefore, it features wider operating conditions range. To sum up, this is
Fluororubber (FKM)
220 a superior oil seal material.
: Excellent, : Good, : Fair, : Poor (must not be used)
19
Bearing Seals
(3) S grease seal (Fig. 6.3)

The S grease seal (synthetic rubber seal with spring)
excels in sealing performance and is well suited for
grease or oil lubrication. Custom specification variants
can be used in a plummer block.
Its recommended peripheral speed falls within a range
of 10 to 12 m/s. The surface roughness and hardness of
the shaft in contact with this sealing material necessitates
special attention.
Fig. 6.5 Special labyrinth seal
Shaft design specification for the area in contact with the seal
The quality of a shaft section in contact with the seal lip
greatly affects the sealing performance of the seal.
Therefore, strictly adhere to the design standard for
shafts in Table 6.2.
Table 6.2 Shaft design standard
Criterion Design standard Remarks

Fig. 6.4 Labyrinth seal
Hardness HRC3040
Surface The finish surface should

6.2 Non-contact seals 0.8Ra or smaller be finish-ground without
roughness infeed.
(1) Labyrinth seal (Fig. 6.4) The end face to which a
Chamfering seal is fitted must be
The labyrinth seal used in the bore of plummer blocks -- at end face tapered and the sharp
SD31TS and SD32TS series-- comprise a labyrinth corner must be rounded.
ring that is fitted into the bore of the plummer block. A

labyrinth seal is used in clearance fit to a shaft (h9)
together with an O-ring so that it can be readily installed 6.3 Combination seals
and can follow expansion/compression of the shaft. The combination seals used for the SBG series are
This seal type excels in sealing performance, and can unique seals that comprise both of an oil seal and
be used for grease or oil lubrication. labyrinth seal and are installed in the bore of a plummer
block. They are used in environments where heavy dust
and contaminants are present.
For better sealing effect, the labyrinth seal is often filled
with grease.
Fig. 6.4 Labyrinth seal
(2) Special labyrinth seal (Fig. 6.5) Fig. 6.6 Combination seal
The special labyrinth seals such as those in Fig. 6.5 are
very useful for applications where heavy soil and dust are
With a continuous or intermittent lubrication
present.
scheme, lubricant can tend to leak. Use a seal
The plummer blocks used in conjunction with this seal
that positively offers reliable sealing.
type are manufactured per custom specifications. For
further information, contact NTN Engineering.
20
Shaft Design
7. Shaft Design
7.1 Bearing-to-shaft fit

The tolerance requirements of the shaft outside
diameter differs between a bearing with an adapter and a
cylindrical bore bearing each mounted to a plummer
block. Table 7.1 summarizes the recommended bearing-
to-shaft fits.
A bearing with an adapter is installed to a shaft by
means of an adapter. A cylindrical bore bearing is usually
positioned in interference fit by a shaft shoulder and
secured with a nut and washer. For this application, the
Fig. 7.1
shaft is provided with threading and washer groove as
illustrated in Fig. 7.1.
Table 7.1 Recommended bearing-to-shaft fit
Shaft outside diameter Shaft type and

Bearing bore type Load condition Remarks
tolerance class
Self-aligning ball bearing Self-aligning roller bearing
The tolerance class for transmission shafts
Tapered bore
may be h10/IT7. "IT5" or IT7" means that the
(complete with Various loads All bearing sizes H9/IT5
shaft form tolerance (circularity, cylidricity,
adapter assembly)
etc.) must satisfy tolerance class IT5 or IT7.
Light load essentially means a load as small
Light load and over 18, incl. 100 J6 as 6 to 7% the basic dynamic load rating.
fluctuating load over 100, incl. 200 k6
Pr0.07Cr
over 18, incl. 100 k5
over 100, incl. 200 over 40, incl. 65 m5 Normal load is a load that satisfies
Normal load over 65, incl. 100 m6 0.06CrPr0.12Cr.
Cylindrical bore
over 100, incl. 140 n6
over 140, incl. 280 p6
Heavy load is a load that satisfies Pr0.12Cr.
over 50, incl. 100 n6 For this type of application, use a bearing
Heavy load and
over 100, incl. 140 p6 whose clearance is greater than normal
shock load
over 140 r6 clearance.
7.2 Mounting dimensions Table 7.2 Fillet radius and shoulder height of shaft
Unit: mm
To be able to correctly seat a cylindrical bore bearing to
the shaft shoulder, the height and fillet radius ras of the Chamfer Shoulder Fillet radius
dimension height h 1
shoulder must be greater than the chamfering rs min of the rs min mm (min) ras max
bearing as specified in Table 7.2.
1 2.75 1
If the bearing is used on the shaft end, the configuration
1,1 3.5 1
must be designed such that the shaft end does not 1,5 4.25 1.5
interfere with the face of bearing bore. For reference, 2 5 2
Table 7.3 provides the wall thickness values at the 2.1 6 2
bearing bore. 2.5 6 2
3 7 2.5
4 9 3
5 11 4
6 14 5
7.5 18 6
9.5 22 8
1 The shoulder height must be greater than
that specified when the shaft is subjected to
a greater axial load.
21
Shaft Design
Table 7.3 Wall thickness at the bearing bore

(1) Unit: mm (2) Unit: mm
Bearing number K Bearing number K Bearing number K Bearing number K Bearing number K Bearing number K
SN 506 11 SN 606 11 SN 206 11 SD 534 44 SD3340 44 SN3024 20

507 11 607 11 (SNZ) 207 11 536 44 3344 48 3026 20
508 11 608 11 208 13 538 48 3348 48 3028 22
509 11 609 11 209 13 540 48 3352 54 3030 22
544 54 3356 54 3032 22
SN 510 11 SN 610 11 SN 210 13
511 14 611 14 (SNZ) 211 14 SD 548 52 SD3360 58 SN3034 24
512 14 612 14 212 16 552 58 3364 58 3036 24
513 14 613 14 213 16 556 58 3368 60 3038 24
515 14 615 14 214 16 560 60 3372 60
564 60 3376 60
SN 516 16 SN 616 16 SN 215 16
517 16 617 16 (SNZ) 216 17 SD 634 48 SD3440 48 SN3122 20
518 16 618 16 217 17 636 48 3444 48 3124 20
519 16 619 16 218 18 638 54 3448 54 3126 20
520 18 620 18 219 18 640 54 3452 52 3128 22
644 58 3456 58 3130 22
SN 522 20 SN 622 20 SN 220 20
524 20 624 20 (SNZ) 222 22 SD 648 58 SD3460 58 SN3132 24
526 20 626 20 224 22 652 60 3464 60 3134 24
528 23 628 23 226 22 656 60 3468 60 3136 24
530 23 630 23 228 23 3138 24
SN 532 25 SN 632 25 SN 230 23 Note: For SD31TS and SD32TS, K=37 mm.
(SNZ) 232 25 The dimensions for SD30 and SD31 are the same as those of
SD33 and SD34.
Note: The dimensions for model SN3 are the same as those of model SN2.
22
Lubrication
8. Lubrication
8.1 Grease lubrication Table 8.3 (1) Volume of grease filled into models SN5 and SN6
Usually, plummer blocks are lubricated with grease. Bearing Grease volume Bearing Grease volume
number (g) number (g)
Grease lubrication leads to good sealing performance
and simpler seal design. SN506 20 30 SN606 27 41
SN507 30 45 SN607 35 52
SN508 37 55 SN608 50 75
(1) Characteristics of grease
SN509 37 55 SN609 75 110
Grease is prepared by mixing base oil such as mineral
oil or synthetic oil with thickener. The characteristics of SN510 47 70 SN610 100 150
SN511 55 80 SN611 110 160
grease vary depending on types and combination of
SN512 80 120 SN612 130 190
various additives. SN513 100 150 SN613 160 240
The typical grease types and their characteristics are SN515 130 190 SN615 230 350
summarized in Table 8.1.
SN516 140 210 SN616 250 380
Depending on the intended application, a grease of SN517 170 260 SN617 320 480
appropriate consistency number is used as summarized SN518 260 390 S618 370 550
in Table 8.2. SN519 250 370 S619 470 700
SN520 330 500 S620 500 750
SN522 470 700 S622 7001 000
Table 8.2 Grease consistency
SN524 550 850 S624 9501 400
NLGI JIS (ATM) SN526 650 950 S626 1 1001 600
consistency worked Applications SN528 8001 200 S628 1 3002 000
number penetration SN530 1 1001 600 S630 1 6002 400
SN532 1 3002 000 S632 1 8002 700
0 355385 Centralized lubrication
1 310340 Centralized lubrication
2 265295 General or capped bearing
3 220250 General or high temperature Table 8.3 (2) Volume of grease filled into model SD
4 175205 Special application
Bearing Grease volume Bearing Grease volume
SD3340 1 400 2 100 SD534 1 500 2 300
(2) Grease volume SD3344 1 700 2 600 SD536 1 800 2 700
SD3348 2 000 3 000 SD538 1 900 2 900
When grease is packed into a bearing, the inside of the
SD3352 2 700 4 000 SD540 2 300 3 400
bearing is first filled with grease. During this course, the SD3356 3 400 5 100 SD544 3 000 4 500
grease must be also filled into the inside guide way of the
bearing cage. SD3360 3 500 5 700 SD548 3 700 5 600
SD3364 4 300 6 400 SD552 4 800 7 200
As a guideline, the recommended volume of grease
SD3368 5 600 8 400 SD556 6 000 9 000
filled in plummer blocks is given below. SD3372 6 300 9 400 SD560 6 70010 000
General application SD3376 6 600 9 900 SD564 9 30014 000
About 1/3 to 1/2 the empty space
SD3440 1 500 2 200 SD634 1 900 2 900
Relatively high speed application SD3444 2 300 3 400 SD636 2 500 3 700
About 1/2 the empty space SD3448 2 300 3 500 SD638 2 700 4 000
Low speed application SD3452 2 700 4 000 SD640 3 300 5 000
More than 1/2 the empty space SD3456 3 200 4 800 SD644 3 800 5 700
SD3460 4 400 6 600 SD648 5 400 8 100
The volume of grease should be carefully selected as it SD3464 5 100 7 700 SD652 6 500 9 800
can lead to overheating of the bearing, outward leakage SD3468 6 7001 0000 SD656 8 70013 000
from the seal, or ingress of dust.
The recommended volume of grease commonly filled in
the applicable bearings are summarized in Table 8.3. Table 8.3 (3) Volume of grease filled into models SN30 and SN31
Bearing Grease volume Bearing Grease volume
SN3024 260 390 SN3122 260 380
SN3026 370 550 SN3124 350 550
SN3028 420 650 SN3126 400 600
SN3030 490 750 SN3128 470 700
SN3032 6501 000 SN3130 7001 000
SN3034 8001 200 SN3132 8501 300
SN3036 1 0001 500 SN3134 9501 400
SN3038 1 0001 500 SN3136 1 1001 700
SN3138 1 3002 000
23
Handling the Plummer Blocks and Bearings
9. Handling the Plummer Blocks and Bearings
Rolling bearings are precision components. To maintain

their accuracies, they must be handled very carefully. In
particular, they must be kept clean, not be subjected to
strong impact, and be protected against possible rusting.
Plummer blocks also need similar handling practices.
9.1 Inspection before installation

Before installing a bearing and a plummer block, the
following points must be thoroughly checked and
inspected.
(1) Prepare installation tools, measuring instruments, oil
stone, lubricant and factory cloth. Before the
installation work, remove dust and impurities from
Fig. 9.3
these tools. (Fig. 9.1)
(5) Check the flatness of the mounting face of the

plummer block. (When placed on a frame, the
plummer block must be stably seated.)
9.2 Preparation for installing the bearing

(1) Unpack the bearing just before the installation work.
(2) If the bearing is to be grease-lubricated, the rust-
proof coating on it may remain unremoved. If it is to
be oil-lubricated, remove the coating with benzene
or kerosene.
(3) For a bearing with an adapter, check its radial
clearance before the installation work. To do so,
place it on a flat work bench, and fit a thickness
Fig. 9.1 gage between the uppermost roller and the raceway
surface on the outer ring to measure the clearance
(2) Make sure that the shaft is free from bends or other (Fig. 9.4). Do not force the thickness gage in or turn
damages and that it has been dimensioned and the bearing. Otherwise, the resultant clearance
formed as specified. (Fig. 9.2) measurement will be greater than the actual
clearance.
Fig. 9.2
(3) Remove dent marks (even though very small) from

the mating faces with an oil stone or fine emery
paper. Check that the contact face to the seal has
specified surface roughness (0.8a). Wipe dust away
from the shaft with clean factory cloth. Fig. 9.4
(4) Remove possible dust and metal chips from the
inside of plummer block. (Fig. 9.3)
24
9.3 Installation of the bearing and associated

components
Once careful checking is complete, install the bearing
and associated components. For the positional
relationship, see Fig. 9.5.
Fig. 9.6
Fig. 9.5
When a bearing is installed onto a shaft or into a

housing, do not directly hit its end face with a hammer
or drift as shown in Fig. 9.6. Otherwise, its design
performance can be lost. Always evenly exert force
around the entire bearing ring face. Also, do not apply
force to one bearing ring (for example, outer ring) as in
Fig. 9.7 to convey the force via the rolling elements to Fig. 9.7
the other bearing ring (inner ring) to install the latter.
Otherwise, a dent mark or other damage can occur on
either or both rings.
When installing a cylindrical bore bearing, whose

interference is relatively small, its whole inner ring can
be uniformly press-fitted at an ordinary temperature as
illustrated in Fig. 9.8. Usually, the inner ring is press-
fitted by tapping the sleeve with a hammer. However,
when many bearings must be installed at a time, a
mechanical or hydraulic press will be helpful.
When installing a non-separable bearing to the shaft
Fig. 9.8 Press-fitting the inner ring
and housing at a time, apply a press-fitting force to
both the inner and outer rings by using a pressure
distribution pad as in Fig. 9.9.
Fig. 9.9 Simultaneous press-fitting of the inner and outer rings
25
9.3.1 Bearing with an adapter the slit with a flat-blade screwdriver for easy fitting.
(1) Thinly apply highly viscous mineral oil to the taper, FIg. 9.11
threading and the chamfered face of the nut (see
Fig. 9.10) before press-fitting. In particular, apply
molybdenum bisulfide paste to these areas on a
large bearing. This prevents scuffing, and allows
easy bearing removal. Before the installation work,
remove oil from the shaft and the bore face of
sleeve with a clean factory cloth.
Fig. 9.11
(3) Fit the bearing over the adapter sleeve on the shaft
as tight as possible, so that the bearing inner ring is
fully seated onto the taper on adapter sleeve.
(4) Lightly tighten the nut until the sleeve is seated on
the shaft.
(5) When fully tightening a self-aligning ball bearing,
make sure that its radial clearance becomes
approximately 1/2 that before fitting. For a self-
aligning roller bearing, tighten the nut while
Fig. 9.10
measuring its radial clearance with a thickness gage
so that the reduction of radial internal clearance
(2) Mount the adapter to a correct position considering value in Table 9.1 is reached. Make sure that an
the dimension B1, B2 or B3 in the bearing table. installed self-aligning ball bearing can turn smoothly
When fitting the adapter sleeve onto the shaft, open by hand (ss Figs. 9.12 and 9.13).
Table 9.1 Installation of tapered bore self-aligning roller bearings Unit: mm

Nominal bearing Reduction of radial Axial displacement drive up Minimum allowable
bore diameter internal clearance residual clearance
d Taper 1/12 Taper 1/30
over incl. min max min max min max CN C3 C4
30 40 0.02 0.025 0.35 0.4 0.015 0.025 0.04
40 50 0.025 0.03 0.4 0.45 0.02 0.03 0.05
50 65 0.03 0.035 0.45 0.6 0.025 0.035 0.055
65 80 0.04 0.045 0.6 0.7 0.025 0.04 0.07
80 100 0.045 0.055 0.7 0.8 1.75 2.25 0.035 0.05 0.08
100 120 0.05 0.06 0.75 0.9 1.9 2.25 0.05 0.065 0.1
120 140 0.065 0.075 1.1 1.2 2.75 3 0.055 0.08 0.11
140 160 0.075 0.9 1.2 1.4 3 3.75 0.055 0.09 0.13
160 180 0.08 0.1 1.3 1.6 3.25 4 0.06 0.1 0.15
180 200 0.09 0.11 1.4 1.7 3.5 4.25 0.07 0.1 0.16
200 225 0.1 0.12 1.6 1.9 4 4.75 0.08 0.12 0.18
225 250 0.11 0.13 1.7 2 4.25 5 0.09 0.13 0.2
250 280 0.12 0.15 1.9 2.4 4.75 6 0.1 0.14 0.22
280 315 0.13 0.16 2 2.5 5 6.25 0.11 0.15 0.24
315 355 0.15 0.18 2.4 2.8 6 7 0.12 0.17 0.26
355 400 0.17 0.21 2.6 3.3 6.5 8.25 0.13 0.19 0.29
400 450 0.2 0.24 3.1 3.7 7.75 9.25 0.13 0.2 0.31
450 500 0.21 0.26 3.3 4 8.25 10 0.16 0.23 0.35
500 560 0.24 0.3 3.7 4.6 9.25 11.5 0.17 0.25 0.36
560 630 0.26 0.33 4 5.1 10 12.5 0.2 0.29 0.41
630 710 0.3 0.37 4.6 5.7 11.5 14.5 0.21 0.31 0.45
26
(7) If it is difficult to tighten a large bearing by manual

force, use a hydraulic nut or ram for easier
assembly. (See Fig. 9.15.)
Fig. 9.12
Fig. 9.15
(8) Make sure the bearing clearance is as specified,

then bend one tab on the washer that corresponds
with the cutout on the circumference of the nut to
maintain the adjustment (Fig. 9.16). Do not loosen
the nut to allow the cutout to match the tab.
Fig. 9.13
(6) To tighten the nut, use a spanner wrench illustrated

in Fig. 9.14.
When tightening the nut with a hammer and a drift,
be sure that the chip from the drift does not enter
the bearing.
Fig. 9.16
(9) When a large bearing is installed to a shaft, its outer

ring will be deformed by its own weight into an
elliptical form. The clearance measurement at the
lowest point on a deformed bearing will be greater
than a true clearance. Remember that a radial
clearance value measurement at this point will result
in excessively large tightening allowance.
(10) The adapter used on a large bearing whose bore

number is 44 or greater is a lock plate type (Fig.
9.17). For this arrangement, first tighten the nut,
then fit the lock plate into the cutout on the nut. In
this case too, do not loosen the nut to allow the
cutout to match the lock plate. Once the lock plate is
seated in the cutout, secure the adjustment with a
Fig. 9.14
spring washer and a hexagonal nut.
27
Fig. 9.17
9.3.2 Cylindrical bore bearing

(1) Press-fitting
a. It is recommended that a small bearing of smaller
tightening allowance be press-fitted by forcing a
press-fitting jig onto the end face of inner ring.
(See Fig. 9.18.) Fig. 9.19
d. After fitting the bearing onto a shaft, allow it to

cool off. Note that the bearing will also shrink in
the axial direction. To avoid gap occurrence
between the bearing face and the shaft shoulder,
force the bearing against the shaft shoulder until
the bearing and shaft have fully cooled down.
Alternatively, tap the bearing several times in the
axial direction through a jig to bring the bearing in
close contact with the shaft before the bearing
and shaft have fully cooled down.
Fig. 9.18
b. For easy fitting, apply mineral oil or molybdenum

bisulfide lubricant to fitting surfaces on the shaft
and bearing. During the press-fitting work, make
sure that the bearing inner ring is not tilted.
(2) Shrink-fitting
a. To install a medium or large bearing, a shrink- Fig. 9.20
fitting technique can be conveniently employed.
The heating temperature for shrink-fitting can be e. Make sure the bearing is fully seated on the shaft
selected from Fig. 9.19 based on the bearing shoulder. Then, insert the washer and nut over
dimensions and tightening allowance the shaft, and secure the bearing by tightening
requirements. Remember the temperature of the the nut. Once the nut has been fully tightened,
bearing must not exceed 120C. bend a tab on the washer and fit it into the cutout
b. Usually, the bearing is heated in oil (Fig. 9.20). on the nut. If a tab cannot be readily fitted into the
However, it may be heated in a heater. cutout, further turn the nut until the tab meets the
c. The oil used as a heating medium is clean cutout.
machine oil #1 or transformer oil #1.
The heating oil bath must be amply sized and
contain sufficient amount of oil. Be careful not to
allow the bearing to directly contact the vessel.
28
9.4 Assembling the plummer blocks

When installing two or more plummer blocks on a shaft,
use one block to locate the outer ring of a bearing in the
axial direction, and arrange the other block (s) so that the
outer ring (s) of bearing (s) in the latter block (s) can
move freely in the axial direction. (See Fig. 9.21.)
Once the bearing has been installed to the shaft and the
associated components have been inserted over the
shaft, assemble the plummer blocks according to the
following procedure.
Fig. 9.23
(3) Adjust the position of the plummer block of the non-

locating bearing to center the bearing to the bearing
seating.
If the plummer block is to be used in a high temperature
environment, carefully position the bearing considering
Non-locating side Locating side
the thermal expansion of the shaft.
(4) Once the bearing is correctly located, check the

squareness of the plummer block relative to the
shaft (make sure the face of bearing inner ring is
parallel with that of the outer ring). Only then, fully
tighten the nut. Remember a larger mounting error
can cause the seal to fail or the shaft to interfere
with the bearing bore, leading to non-smooth
Locating side Locating side running (Fig. 9.24). If such a problem occurs,
(with one stabilizing ring) (with two stabilizing rings) correct the mounting seat, and then, install the lower
Fig. 9.21 plummer block housing.
(1) Temporarily install the lower plummer block housing

to the frame. (See Fig. 9.22.)
Fig. 9.22
Fig. 9.24
(2) Fit the locating bearing into the lower plummer block
housing, together with the seal and stabilizing ring.
(See Fig. 9.23.)
29
(5) If the bearing is lubricated with grease, fill the

bearing interior with grease, and apply grease to the
mating surfaces of the upper and lower plummer
block housings. Also, amply apply grease to the
sliding surface of the seal. In the case of a self-
aligning roller bearing, incline the outer ring to allow
a sufficient volume of grease to be packed into the
gaps between the rollers and the cage. (For the
volume of grease, refer to Section 11.)
(6) In the case of oil-lubricated bearings, fill the oil up to the

center of the lowest rolling element. (See Fig. 9.25.)
Fig. 9.27
9.5 Running inspection

Once the bearing arrangement has been assembled,
make sure the assembly work has been correctly
achieved by following the procedure below.
(1) First, turn the bearing by hand to check that the
bearing and seal are free from any irregularities.
a. Non-smooth touch: Trapped dust or scratch
b. Irregular torque: Abnormal interference
c. Excessively large running torque:
Too small bearing clearance, poor flatness of
mounting seat
(2) Next, run the bearing by power. Begin with no load

Fig. 9.25 and at lower speed.
a. Abnormal noise:
(7) After filling with lubricant, check the mating surfaces Dust, dent mark, or poor lubrication
between the upper and lower plummer block b. Vibration:
housings are stably in contact with each other. Greater misalignment, or excessively large
Remember to apply grease to the mating surfaces residual clearance
on the plummer block housings to ensure reliable
sealing and rust-proofing. Then, fully tighten the (3) Run the bearing under normal operating conditions
tightening bolt. (See Fig. 9.26.) to check for temperature rise on the bearing. The
Note that either the upper or lower housing of a possible causes to abnormal temperature rise with
particular plummer block is incompatible with the bearings are as follows:
lower or upper housing of another plummer block. a. Allowable speed has been exceeded.
Do not confuse the like housings. b. Overloading
Knock pin seats (Fig. 9.27) are provided at the c. Too small residual clearance
corners of the bed so locking knock pins can be driven d. Negative clearance owing to excessive expansion
into these seats. Use these seats when intending to or compression with the shaft
install a plummer block with utmost precision. e. Warped plummer block owing to poor flatness
with the mounting seat
f. Poor lubrication (excessive or insufficient
lubricant, inappropriate lubrication method of
lubricant)
g. Too great tightening allowance for the contact
seal, or interference with rotating components
such as those around the labyrinth seal
If any irregularity is found as a result of running

inspection, determine and remove the cause. Then,
reperform the running inspection to make sure the
bearing runs normally.
Fig. 9.26
30
9.6 Maintenance and inspection 9.7.2 Cylindrical bore bearing

Usually, a cylindrical bore bearing is interference-fitted.
To be able to use a bearing to its design life and avoid
Thus, the bearing is simply drawn out by placing a jig to
any accident, check the following points at regular
the face of the inner ring and exerting a force as
intervals.
illustrated in Fig. 9.29 with a hand press. However, be
(1) Running sound on bearing
careful not to apply a force to the outer ring. A puller such
(2) Temperature on bearing or plummer block
as that shown in Fig. 9.30 is often used. When using this
(3) Vibration on shaft
tool, make sure that the jig is fully engaged with the face
(4) Leaking grease or worn oil seal
of the inner ring.
(5) Loose tightening and mounting bolts
(6) Trouble-free operation of the lubrication system, and
loosening or leakage with piping
If the bearing arrangement must be inspected while it is

at a standstill, check it for the following points:
(1) Check appearance the of bearing for any
irregularity.
(2) Fouling of grease, or contaminants (dust or steel
dust) in grease
(3) Loose adapter sleeve
(4) Worn or damaged seal
9.7 Bearing disassembly

9.7.1 Bearing with adapter
Straighten the bent tab on the washer, and loosen the
Fig. 9.29
nut by two to three turns. Place a drift to a face of the nut.
Lightly tap the drift to turn the sleeve (Fig. 9.28). Once
the sleeve is shifted in the axial direction, the bearing can
be easily removed.
Note, however, when the nut has been excessively
loosened and only a few ridges remain engaged, and if
the nut is further tapped, the threading on the sleeve or
nut may be stripped.
Fig. 9.30
Fig. 9.28
31
9.8 Cleaning the bearing 9.9 Storing the bearing

Clean the removed bearing with diesel oil or kerosene. When storing a bearing, pay particular attention to rust
Use two vessels: one for rough cleaning and the other for prevention. Note that the rust-proofing grease in the
finish cleaning. Prepare a cleaning station that has a bearing will run away at a temperature of 50 to 60C.
metal screen as illustrated in Fig. 9.31 so that the bearing Therefore, store a bearing in a dry, cool location at a
does not directly contact the fouling on the bottom of height at least 30 cm above the floor. Remember that
vessel. In rough cleaning, virtually all oil and foreign wooden crate attracts moisture. Thus, immediately
matters should be removed from the bearing which unpack the delivered bearings, and store them on
should be immediately transferred to the finish vessel. shelves.
The finish vessel must be provided with a filter unit to
maintain the cleaning agent clean.
Once cleaned, the bearing must be immediately rust-
proofed.
The bearings (which have been carefully removed) must
be checked whether they can be reused. The judging
criterion for reuse should be determined considering the
following criteria through a trial-and-error basis.
(1) Scheduled operating duration to next regular
inspection
(2) Importance of the machine that uses the bearing in
question
(3) Operating conditions such as loading and bearing
speed
(4) Severity of damage on the rolling contact surface
(5) Tendency of increasing bearing clearance and wear
on the cage
(6) Loss in accuracy, etc.
Fig. 9.31
32
Index of Bearing Tables
Split type
SN5 34
SN6S6 36
SN30SN3138
SNZ2 40
SNZ3SZ3 42
SD5SD5GSD6SD6G 44
SD30SD30G 46
SD31SD31G 48
SD2SD2GSD3SD3G 50
Unit type
SV5 52
SV2 56
Plummer Blocks SN5
Standard type / For bearing with adapter assembly
N t
N1
A1 H2
S
H
J H1
d1 25140mm
Shaft Bearing Abutment and fillet dimensions Approx. Mass

dia. numbers
mm mm kg
d1 D H J N1 N A L A1 H1 H2 g t S
nominal nominal
number number (approx.)
25 SN506 62 50 150 15 20 77 185 52 22 90 30 M8 M12 1.7
30 SN507 72 50 150 15 20 82 185 52 22 95 33 M10 M12 2.2
35 SN508 80 60 170 15 20 85 205 60 25 110 33 M10 M12 2.6
40 SN509 85 60 170 15 20 85 205 60 25 112 31 M10 M12 2.8
45 SN510 90 60 170 15 20 90 205 60 25 115 33 M10 M12 3.0
50 SN511 100 70 210 18 23 95 255 70 28 130 33 M12 M16 4.0
55 SN512 110 70 210 18 23 105 255 70 30 135 38 M12 M16 4.5
60 SN513 120 80 230 18 23 110 275 80 30 150 43 M12 M16 5.6
65 SN515 130 80 230 18 23 115 280 80 30 155 41 M12 M16 6.0
70 SN516 140 95 260 22 27 120 315 90 32 175 43 M16 M20 9.0
75 SN517 150 95 260 22 27 125 320 90 32 185 46 M16 M20 9.3
80 SN518 160 100 290 22 27 145 345 100 35 195 62.4 M16 M20 12
85 SN5192 170 112 290 22 27 140 345 100 35 210 53 M16 M20 14
90 SN520 180 112 320 26 32 160 380 110 40 218 70.3 M20 M24 17
100 SN522 200 125 350 26 32 175 410 120 45 240 80 M20 M24 20
110 SN524 215 140 350 26 32 185 410 120 45 270 86 M20 M24 23
115 SN526 230 150 380 28 36 190 445 130 50 290 90 M24 M24 29
125 SN528 250 150 420 33 42 205 500 150 50 305 98 M24 M30 37
135 SN530 270 160 450 33 42 220 530 160 60 325 106 M24 M30 42
140 SN532 290 170 470 33 42 235 550 160 60 345 114 M24 M30 48
1 The numeral in nominal number of the setting ring represents the outside 4 11 through 18 for bearing series 222 are also applicable to type E self-aligning
diameter Tand width dimension. roller bearings. For details, contact NTN Engineering.
2 Though not JIS part number, SN519 complies with JIS.
3 Dimension Y is an approximate distance from the bearing center to the shaft NOTE: 1) Sizes SN524 and greater are equipped with lifting eye bolts.
end for shaft end configuration.
34
Plummer Blocks SN5
A
g
A/2
Y
d1 D
x x
Nominal number Approx. Seal shaft

number dia.
Self-aligning setting spherical roller setting mm mm
ball bearings washer 1 bearings washer Y3 d1
number number
1206K;H206X SR 62X 7 2 18
2206K;H306X SR 62X10 1 20 ZF6 25
1207K;H207X SR 72X 8 2 19
2207K;H307X SR 72X10 1 22 ZF7 30
1208K;H208X SR 80X 7.5 2 21
2208K;H308X SR 80X10 1 22208CK;H308X SR80X10 1 23 ZF8 35
1209K;H209X SR 85X 6 2 22
2209K;H309X SR 85X 8 1 22209CK;H309X SR85X 8 1 24 ZF9 40
1210K;H210X SR 90X 6.5 2 24
2210K;H310X SR 90X10 1 22210CK;H310X SR90X10 1 25 ZF10 45
1211K;H211X SR100X 6 2 25
2211K;H311X SR100X 8 1 22211BK;H311X4 SR100X 8 1 27 ZF11 50
1212K;H212X SR110X 8 2 26
2212K;H312X SR110X10 1 22212BK;H312X4 SR110X10 1 29 ZF12 55
1213K;H213X SR120X10 2 28
1215K;H215X SR130X 8 2 30
1216K;H216X SR140X 8.5 2 32
1217K;H217X SR150X 9 2 34
1218K;H218X SR160X16.2 2 22218EK;H318X 35
2218K;H318X SR160X11.2 2 22218BK;H318X4 SR160X11.2 2 40
SR160X10 1 ZF18 80
23218BK;H2318X 46
1219K;H219X SR170X10.5 2 37
2219K;H319X SR170X10 1 22219BK;H319X SR170X10 1 43 ZF19 85
1220K;H220X SR180X18.1 2 39
2220K;H320X SR180X12.1 2 22220BK;H320X SR180X12.1 2 45 ZF20 90
23220BK;H2320X SR180X10 1 52
1222K;H222X SR200X21 2 42
2222K;H322X SR200X13.5 2 22222BK;H322X SR200X13.5 2 50
23222BK;H2322X SR200X10 1 ZF22 100
58
22224BK;H3124X SR215X14 2 53
23224BK;H2324X SR215X10 1 62 ZF24 110
22226BK;H3126 SR230X13 2 57
23226BK;H2326 SR230X10 1 65 ZF26 115
22228BK;H3128 SR250X15 2 60
23228BK;H2328 SR250X10 1 70 ZF28 125
22230BK;H3130 SR270X16.5 2 65
23230BK;H2330 SR270X10 1 76 ZF30 135
22232BK;H3132 SR290X17 2 71
23232BK;H2332 SR290X10 1 83 ZF32 140
2) Fill and drain plugs: 4) As an adaptor for bearing series 12, series H2 as well as series H3 can be
Size: SN506-SN520PT1/8 used.
SN522-SN532PT1/4 5) Materials of setting washers:
3) Dimension X indicates a deviation of the bearing center relative to the SR62-SR250 Die-casting zinc alloy, category 2, ZDC2
plummer block center, and its value is 1/2 the width of the setting washer. SR270-SR290 Gray cast iron, category 3, FC200
35
Plummer Blocks SN6S6
N t
N1
A1 H2
S
H
J H1
d1 25140mm
Shaft Bearing Abutment and fillet dimensions Approx. Mass Nominal number
dia. numbers
mm mm kg Self-aligning
d1 D H J N1 N A L A1 H1 H2 g t S ball bearings
nominal nominal
1306K;H306X
25 SN606 72 50 150 15 20 82 185 52 22 95 37 M10 M12 2.3 2306K;H2306X
1307K;H307X
30 SN607 80 60 170 15 20 90 205 60 25 110 41 M10 M12 3.0 2307K;H2307X
1308K;H308X
35 SN608 90 60 170 15 20 95 205 60 25 115 43 M10 M12 3.1 2308K;H2308X
1309K;H309X
40 SN609 100 70 210 18 23 105 255 70 28 130 46 M12 M16 4.4 2309K;H2309X
1310K;H310X
45 SN610 110 70 210 18 23 115 255 70 30 135 50 M12 M16 5.0 2310K;H2310X
1311K;H311X
50 SN611 120 80 230 18 23 120 275 80 30 150 53 M12 M16 5.8 2311K;H2311X
1312K;H312X
55 SN612 130 80 230 18 23 125 280 80 30 155 56 M12 M16 7.7 2312K;H2312X
1313K;H313X
60 SN613 140 95 260 22 27 130 315 90 32 175 58 M16 M20 9.8 2313K;H2313X
1315K;H315X
65 SN615 160 100 290 22 27 140 345 100 35 195 65 M16 M20 12 2315K;H2315X
1316K;H316X
70 SN616 170 112 290 22 27 145 345 100 35 212 68 M16 M20 15 2316K;H2316X
1317K;H317X
75 SN617 180 112 320 26 32 155 380 110 40 218 70 M20 M24 17 2317K;H2317X
1318K;H318X
80 S618 190 112 320 26 35 160 400 110 33 230 74 M20 M24 21 2318K;H2318X
1319K;H319X
85 S619 200 125 350 26 35 170 420 120 36 245 77 M20 M24 24 2319K;H2319X
1320K;H320X
90 S620 215 140 350 26 35 175 420 120 38 280 83 M20 M24 29 2320K;H2320X
1322K;H322X
100 S622 240 150 390 28 38 190 460 130 40 300 90 M24 M24 38 2322K;H2322X
110 S624 260 160 450 33 42 205 540 160 50 325 96 M24 M30 47
115 S626 280 170 470 33 42 215 560 160 50 350 103 M24 M30 54
125 S628 300 180 520 35 45 235 630 170 55 375 112 M30 M30 70
135 S630 320 190 560 35 45 245 680 180 55 395 118 M30 M30 75
140 S632 340 200 580 42 52 255 710 190 60 415 124 M30 M36 80
1 The numeral in nominal number of the setting ring represents the outside NOTE: 1) Sizes S618 and greater are equipped with lifting eye bolts.
diameter and width dimension. 2) Fill and drain plugs:
2 Dimension Y is an approximate distance from the bearing center to the shaft Size: SN606-SN617PT1/8
end for shaft end configuration. S618-S632PT1/4
36
Plummer Blocks SN6S6
A
g
A/2
Y
d1 D
x x
Nominal number Approx. Seal shaft

number dia.
setting spherical roller setting mm mm
washer 1 bearings washer Y2 d1
number number
SR 72X 9 2 19
SR 72X10 1 23 ZF6 25
SR 80X10 2 21
SR 80X10 1 26 ZF7 30
SR 90X10 2 21308CK;H308X SR 90X10 2 23
SR 90X10 1 22308CK;H2308X SR 90X10 1 28 ZF8 35
SR100X10.5 2 21309CK;H309X SR100X10.5 2 25
SR100X10 1 22309CK;H2309X SR100X10 1 31 ZF9 40
SR110X11.5 2 21310CK;H310X SR110X11.5 2 27
SR110X10 1 22310CK;H2310X SR110X10 1 34 ZF10 45
SR120X12 2 21311K;H311X SR120X12 2 29
SR120X10 1 22311BK;H2311X SR120X10 1 36 ZF11 50
SR130X12.5 2 21312K;H312X SR130X12.5 2 31
SR130X10 1 22312BK;H2312X SR130X10 1 39 ZF12 55
SR140X12.5 2 21313K;H313X SR140X12.5 2 33
SR140X10 1 22313BK;H2313X SR140X10 1 40 ZF13 60
SR160X14 2 21315K;H315X SR160X14 2 36
SR160X10 1 22315BK;H2315X SR160X10 1 45 ZF15 65
SR170X14.5 2 21316K;H316X SR170X14.5 2 39
SR170X10 1 22316BK;H2316X SR170X10 1 48 ZF16 70
SR180X14.5 2 21317K;H317X SR180X14.5 2 41
SR180X10 1 22317BK;H2317X SR180X10 1 50 ZF17 75
SR190X15.3 2 21318K;H318X SR190X15.3 2 42
SR190X 9.5 1 22318BK;H2318X SR190X 9.5 1 52 ZF18 80
SR200X15.8 2 21319K;H319X SR200X15.8 2 44
SR200X 9.5 1 22319BK;H2319X SR200X 9.5 1 55 ZF19 85
SR215X17.8 2 21320K;H320X SR215X17.8 2 46
SR215X 9.5 1 22320BK;H2320X SR215X 9.5 1 59 ZF20 90
SR240X19.8 2 21322K;H322X SR240X19.8 2 48
SR240X 9.5 1 22322BK;H2322X SR240X 9.5 1 63 ZF22 100
22324BK;H2324X SR260X 9.5 1 67 ZF24 110
22326BK;H2326 SR280X 9.5 1 72 ZF26 115
22328BK;H2328 SR300X 9.5 1 77 ZF28 125
22330BK;H2330 SR320X 9.5 1 82 ZF30 135
22332BK;H2332 SR340X 9.5 1 88 ZF32 140
3) Dimension X indicates a deviation of the bearing center relative to the

plummer block center, and its value is 1/2 the width of the setting washer.
37
Plummer Blocks SN30SN31
N t
N1
A1 H2
S
H
J H1
d1 110170mm
Shaft Bearing Abutment and fillet dimensions Approx.

dia. numbers
mm mm
d1 D H J N1 N A L A1 H1 H2 g t S
nominal nominal
number number
110 SN3024 180 112 320 26 32 150 380 110 40 217 56 M20 M24
115 SN3026 200 125 350 26 32 160 410 120 45 240 62 M20 M24
125 SN3028 210 140 350 26 32 170 410 120 45 260 63 M20 M24
135 SN3030 225 150 380 28 36 175 445 130 50 283 66 M24 M24
140 SN3032 240 150 390 28 36 190 460 130 50 290 70 M24 M24
150 SN3034 260 160 450 33 42 200 530 160 60 310 77 M24 M30
160 SN3036 280 170 470 33 42 210 550 160 60 330 84 M24 M30
170 SN3038 290 170 470 33 42 210 550 160 60 335 85 M24 M30
100 SN3122 180 112 320 26 32 155 380 110 40 217 66 M20 M24
110 SN3124 200 125 350 26 32 165 410 120 45 240 72 M20 M24
115 SN3126 210 140 350 26 32 170 410 120 45 260 74 M20 M24
125 SN3128 225 150 380 28 36 180 445 130 50 283 78 M24 M24
135 SN3130 250 150 420 33 42 200 500 150 50 295 90 M24 M30
140 SN3132 270 160 450 33 42 215 530 160 60 315 96 M24 M30
150 SN3134 280 170 470 33 42 220 550 160 60 330 98 M24 M30
160 SN3136 300 180 520 33 42 230 610 170 70 355 106 M30 M30
170 SN3138 320 190 560 33 42 240 650 180 70 375 114 M30 M30
1 The numeral in nominal number of the setting ring represents the outside NOTE: 1) Sizes SN3028 and greater and sizes SN3126 and greater are
diameter and width dimension. equipped with lifting eye bolts.
2 Dimension Y is an approximate distance from the bearing center to the shaft 2) Fill and drain plugs:
end for shaft end configuration. Size: PT1/4
38
Plummer Blocks SN30SN31
A
g
A/2
Y
d1 D
x x
Mass Nominal number Approx. Seal shaft

number dia.
kg spherical roller setting mm mm
bearings washer 1 Y2 d1
(approx.) number
17 23024BK;H3024X SR180X10 1 47 ZF24 110
20 23026BK;H3026 SR200X10 1 51 ZF26 115
25 23028BK;H3028 SR210X10 1 53 ZF28 125
30 23030BK;H3030 SR225X10 1 56 ZF30 135
33 23032BK;H3032 SR240X10 1 61 ZF32 140
46 23034BK;H3034 SR260X10 1 66 ZF34 150
52 23036BK;H3036 SR280X10 1 70 ZF36 160
52 23038BK;H3038 SR290X10 1 72 ZF38 170
18 23122BK;H3122X SR180X10 1 51 ZF22 100
21 23124BK;H3124X SR200X10 1 55 ZF24 110
26 23126BK;H3126 SR210X10 1 57 ZF26 115
32 23128BK;H3128 SR225X10 1 60 ZF28 125
40 23130BK;H3130 SR250X10 1 68 ZF30 135
45 23132BK;H3132 SR270X10 1 74 ZF32 140
51 23134BK;H3134 SR280X10 1 76 ZF34 150
63 23136BK;H3136 SR300X10 1 81 ZF36 160
76 23138BK;H3138 SR320X10 1 86 ZF38 170
3) Dimension X indicates a deviation of the bearing center relative to the

plummer block center, and its value is 1/2 the width of the setting washer.
39
Plummer Blocks SNZ2
Stepped bore type / For cylindrical bore bearing
N t
N1
A1 H2
S
H
J H1
d1 30160mm
Shaft Bearing Abutment and fillet dimensions Approx. Mass Nominal

dia. numbers number
d d2 d3 D H J N1 N A L A1 H1 H2 g t S ball bearings
nominal nominal
1206
30 25 35 SNZ206 62 50 150 15 20 77 185 52 22 90 30 M 8 M12 1.8 2206
1207
35 30 45 SNZ207 72 50 150 15 20 82 185 52 22 95 33 M10 M12 2.2 2207
1208
40 35 50 SNZ208 80 60 170 15 20 85 205 60 25 110 33 M10 M12 2.9 2208
1209
45 40 55 SNZ209 85 60 170 15 20 85 205 60 25 112 31 M10 M12 3.2 2209
1210
50 45 60 SNZ210 90 60 170 15 20 90 205 60 25 115 33 M10 M12 3.4 2210
1211
55 50 65 SNZ211 100 70 210 18 23 95 255 70 28 130 33 M12 M16 4.5 2211
1212
60 55 70 SNZ212 110 70 210 18 23 105 255 70 30 135 38 M12 M16 5.4 2212
1213
65 60 75 SNZ213 120 80 230 18 23 110 275 80 30 150 43 M12 M16 6.2 2213
1214
70 60 80 SNZ214 125 80 230 18 23 115 275 80 30 155 44 M12 M16 6.7 2214
1215
75 65 85 SNZ215 130 80 230 18 23 115 280 80 30 155 41 M12 M16 7.6 2215
1216
80 70 90 SNZ216 140 95 260 22 27 120 315 90 32 175 43 M16 M20 9.4 2216
1217
85 75 95 SNZ217 150 95 260 22 27 125 320 90 32 185 46 M16 M20 10 2217
1218
90 80 100 SNZ218 160 100 290 22 27 145 345 100 35 195 62.4 M16 M20 13 2218

1219
95 85 110 SNZ219 170 112 290 22 27 140 345 100 35 210 53 M16 M20 16 2219
1220
100 90 115 SNZ220 180 112 320 26 32 160 380 110 40 218 70.3 M20 M24 18 2220

1222
110 100 125 SNZ222 200 125 350 26 32 175 410 120 45 240 80 M20 M24 23 2222

120 110 135 SNZ224 215 140 350 26 32 185 410 120 45 270 86 M20 M24 25
130 115 145 SNZ226 230 150 380 28 36 190 445 130 50 290 90 M24 M24 32
140 125 155 SNZ228 250 150 420 33 42 205 500 150 50 305 98 M24 M30 41
150 135 165 SNZ230 270 160 450 33 42 220 530 160 60 325 106 M24 M30 49
160 140 175 SNZ232 290 170 470 33 42 235 550 160 60 345 114 M24 M30 57
1 The numeral in nominal number of the setting ring represents the outside end for shaft end configuration.
diameter and width dimension.
2 Dimension Y is an approximate distance from the bearing center to the shaft NOTE: 1) Sizes SNZ224 and greater are equipped with lifting eye bolts.
40
Plummer Blocks SNZ2
A
g
A/2
Y Y
d2 d3 D
d
x x
Nominal number Approx. Seal number shaft

dia.
washer 1 bearings washer nut washer Y2 (d2) (d3) d
number number
SR 62X 7 2 18
SR 62X10 1 AN06 AW06 20 ZF 6 ZF 8 30
SR 72X 8 2 19
SR 72X10 1 AN07 AW07 22 ZF 7 ZF10 35
SR 80X 7.5 2 21
SR 80X10 1 22208C SR 80X10 1 AN08 AW08 23 ZF 8 ZF11 40
SR 85X 6 2 22
SR 85X 8 1 22209C SR 85X 8 1 AN09 AW09 24 ZF 9 ZF12 45
SR 90X 6.5 2 24
SR 90X10 1 22210C SR 90X10 1 AN10 AW10 25 ZF10 ZF13 50
SR100X 6 2 25
SR100X 8 1 22211B SR100X 8 1 AN11 AW11 27 ZF11 ZF15 55
SR110X 8 2 26
SR110X10 1 22212B SR110X10 1 AN12 AW12 29 ZF12 ZF16 60
SR120X10 2 28
SR125X10 2 28
SR130X 8 2 30
SR140X 8.5 2 32
SR150X 9 2 34
SR160X16.2 2 35
SR160X11.2 2
22218B SR160X11.2 2 AN18 AW18 40 ZF18 ZF22 90
23218B SR160X10 1 46
SR170X10.5 2 37
SR180X18.1 2 39
SR180X12.1 2
22220B SR180X12.1 2 AN20 AW20 45 ZF20 ZF26 100
23220B SR180X10 1 52
SR200X21 2 42
SR200X13.5 2
22222B SR200X13.5 2 AN22 AW22 50 ZF22 ZF28 110
23222B SR200X10 1 58
22224B SR215X14 2 53
23224B SR215X10 1 AN24 AW24 62 ZF24 ZF30 120
22226B SR230X13 2 57
23226B SR230X10 1 AN26 AW26 65 ZF26 GS33 130
22228B SR250X15 2 60
23228B SR250X10 1 AN28 AW28 70 ZF28 GS35 140
22230B SR270X16.5 2 65
23230B SR270X10 1 AN30 AW30 76 ZF30 GS37 150
22232B SR290X17 2 71
23232B SR290X10 1 AN32 AW32 83 ZF32 GS39 160
2) Fill and drain plugs: 3) Dimension X indicates a deviation of the bearing center relative to the
Size: SNZ206-SNZ220PT1/8 plummer block center, and its value is 1/2 the width of the setting washer.
SNZ222-SNZ232PT1/4
41
Plummer Blocks SNZ3SZ3
Stepped bore type / For cylindrical bore bearing
N t
N1
A1 H2
S
H
J H1
d1 30160mm
Shaft Bearing Abutment and fillet dimensions Approx. Mass Nominal

dia. numbers number
d d2 d3 D H J N1 N A L A1 H1 H2 g t S ball bearings
nominal nominal
1306
30 25 35 SNZ306 72 50 150 15 20 82 185 52 22 95 37 M10 M12 2.1 2306
1306
30 25 40 SNZ306X 72 50 150 15 20 82 185 52 22 95 37 M10 M12 2.1 2306
1307
35 30 45 SNZ307 80 60 170 15 20 90 205 60 25 110 41 M10 M12 3.1 2307
1308
40 35 50 SNZ308 90 60 170 15 20 95 205 60 25 115 43 M10 M12 3.5 2308
1309
45 40 55 SNZ309 100 70 210 18 23 105 255 70 28 130 46 M12 M16 4.8 2309
1310
50 45 60 SNZ310 110 70 210 18 23 115 255 70 30 135 50 M12 M16 5.6 2310
1311
55 50 65 SNZ311 120 80 230 18 23 120 275 80 30 150 53 M12 M16 6.6 2311
1312
60 55 70 SNZ312 130 80 230 18 23 125 280 80 30 155 56 M12 M16 7.9 2312
1313
65 60 75 SNZ313 140 95 260 22 27 130 315 90 32 175 58 M16 M20 11 2313
1314
70 60 80 SNZ314 150 95 260 22 27 130 320 90 32 185 61 M16 M20 12 2314
1315
75 65 85 SNZ315 160 100 290 22 27 140 345 100 35 195 65 M16 M20 13 2315
1316
80 70 90 SNZ316 170 112 290 22 27 145 345 100 35 212 68 M16 M20 16 2316
1317
85 75 95 SNZ317 180 112 320 26 32 155 380 110 40 218 70 M20 M24 18 2317
1317
85 75 100 SNZ317X 180 112 320 26 32 155 380 110 40 218 70 M20 M24 18 2317
1318
90 80 100 SZ318 190 112 320 26 35 160 400 110 33 230 74 M20 M24 21 2318
1318
90 80 105 SZ318X 190 112 320 26 35 160 400 110 33 230 74 M20 M24 21 2318
1319
95 85 110 SZ319 200 125 350 26 35 170 420 120 36 245 77 M20 M24 23 2319
1320
100 90 115 SZ320 215 140 350 26 35 175 420 120 38 280 83 M20 M24 32 2320
1322
110 100 125 SZ322 240 150 390 28 38 190 460 130 40 300 90 M24 M24 42 2322
120 110 135 SZ324 260 160 450 33 42 205 540 160 50 325 96 M24 M30 61
130 115 150 SZ326 280 170 470 33 42 215 560 160 50 350 103 M24 M30 68
140 125 160 SZ328 300 180 520 35 45 235 630 170 55 375 112 M30 M30 95
150 135 170 SZ330 320 190 560 35 45 245 680 180 55 395 118 M30 M30 110
160 140 180 SZ332 340 200 580 42 52 255 710 190 60 415 124 M30 M36 130
1 The numeral in nominal number of the setting ring represents the outside end for shaft end configuration.
diameter and width dimension.
2 Dimension Y is an approximate distance from the bearing center to the shaft NOTE: 1) Sizes SZ318 and greater are equipped with lifting eye bolts.
42
Plummer Blocks SNZ3SZ3
A
g
A/2
Y Y
d2 d3 D
d
x x
Nominal number Approx. Seal number shaft

dia.
washer 1 bearings washer nut washer Y2 (d2) (d3) d
number number
SR 72X 9 2 19
SR 72X10 1 AN06 AW06 23 ZF6 ZF8 30
SR 72X 9 2 19
SR 72X10 1 AN06 AW06 23 ZF6 ZF9 30
SR 80X10 2 21
SR 80X10 1 AN07 AW07 26 ZF7 ZF10 35
SR 90X10 2 21308C SR 90X10 2 23
SR 90X10 1 22308C SR 90X10 1 AN08 AW08 28 ZF8 ZF11 40
SR100X10.5 2 21309C SR100X10.5 2 25
SR100X10 1 22309C SR100X10 1 AN09 AW09 31 ZF9 ZF12 45
SR110X11.5 2 21310C SR110X11.5 2 27
SR110X10 1 22310C SR110X10 1 AN10 AW10 34 ZF10 ZF13 50
SR120X12 2 21311 SR120X12 2 29
SR130X12.5 2 21312 SR130X12.5 2 31
SR140X12.5 2 21313 SR140X12.5 2 33
SR150X13 2 21314 SR150X13 2 34
SR160X14 2 21315 SR160X14 2 36
SR170X14.5 2 21316 SR170X14.5 2 39
SR180X14.5 2 21317 SR180X14.5 2 41
SR180X14.5 2 21317 SR180X14.5 2 41
SR190X15.3 2 21318 SR190X15.3 2 42
SR190X 9.5 1 22318B SR190X9.5 1 AN18 AW18 52 ZF18 ZF22 90
SR190X15.3 2 21318 SR190X15.3 2 42
SR190X 9.5 1 22318B SR190X 9.5 1 AN18 AW18 52 ZF18 ZF23 90
SR200X15.8 2 21319 SR200X15.8 2 44
SR215X17.8 2 21320 SR215X17.8 2 46
SR240X19.8 2 21322 SR240X19.8 2 48
22324B SR260X9.5 1 AN24 AW24 67 ZF24 ZF30 120
22326B SR280X9.5 1 AN26 AW26 72 ZF26 ZF34 130
22328B SR300X9.5 1 AN28 AW28 77 ZF28 ZF36 140
22330B SR320X9.5 1 AN30 AW30 82 ZF30 ZF38 150
22332B SR340X9.5 1 AN32 AW32 88 ZF32 ZF40 160

2) Fill and drain plugs: 3) Dimension X indicates a deviation of the bearing center relative to the
Size: SNZ306-SNZ317PT1/8 plummer block center, and its value is 1/2 the width of the setting washer.
SZ318-SZ332PT1/4
43
Plummer Blocks SD5SD5GSD6SD6G
For heavy load, double rubber sealed type / For bearing with adapter assembly
N
t
N1
J1 A1 H2
S
H
J H1
L
d1 150300mm
Shaft Bearing numbers Abutment and fillet dimensions Approx.

dia.
mm mm
d1 free side fixed side D H J J1 N1 N A L A1 H1 H2 g1 t S
nominal nominal
number number
150 SD534 SD534G 310 180 510 140 32 52 270 620 230 60 360 96 M24 M30
160 SD536 SD536G 320 190 540 150 32 52 280 650 240 60 380 96 M24 M30
170 SD538 SD538G 340 200 570 160 35 55 290 700 260 65 400 102 M30 M30
180 SD540 SD540G 360 210 610 170 35 55 300 740 270 65 420 108 M30 M30
200 SD544 SD544G 400 240 680 190 40 60 330 820 300 70 475 118 M30 M36
220 SD548 SD548G 440 260 740 200 42 62 340 880 310 85 515 130 M36 M36
240 SD552 SD552G 480 280 790 210 42 62 370 940 340 85 560 140 M36 M36
260 SD556 SD556G 500 300 830 230 50 70 390 990 370 100 590 140 M36 M42
280 SD560 SD560G 540 325 890 250 50 70 410 1060 390 100 640 150 M36 M42
300 SD564 SD564G 580 355 930 270 57 77 440 1110 420 110 690 160 M42 M48
150 SD634 SD634G 360 210 610 170 35 55 300 740 270 65 420 130 M30 M30
160 SD636 SD636G 380 225 640 180 40 60 320 780 290 70 450 136 M30 M36
170 SD638 SD638G 400 240 680 190 40 60 330 820 300 70 475 142 M30 M36
180 SD640 SD640G 420 250 710 200 42 62 350 860 320 85 500 148 M36 M36
200 SD644 SD644G 460 280 770 210 42 62 360 920 330 85 550 155 M36 M36
220 SD648 SD648G 500 300 830 230 50 70 390 990 370 100 590 165 M36 M42
240 SD652 SD652G 540 325 890 250 50 70 410 1 060 390 100 640 175 M36 M42
260 SD656 SD656G 580 355 930 270 57 77 440 1 110 420 110 690 185 M42 M48
1 Dimension g represents the bearing seat width for free-side bearing. NOTE: 1) Fill and drain plugs:
Dimension for fixed-side (code G) is 0.5 mm greater than the bearing width Size: PT3/8
dimension.
2 Dimension Y is an approximate distance from the bearing center to the shaft
44
A
g A/2
Y
d1 D

number dia.
kg spherical roller mm mm
bearings Y2 d1
(approx.)
95 22234BK;H3134 75 ZF34 150
110 22236BK;H3136 76 ZF36 160
130 22238BK;H3138 80 ZF38 170
150 22240BK;H3140 84 ZF40 180
210 22244BK;H3144 90 ZF44 200
240 22248BK;H3148 98 ZF48 220
320 22252BK;H3152 105 ZF52 240
370 22256BK;H3156 107 ZF56 260
460 22260BK;H3160 114 ZF60 280
560 22264BK;H3164 122 ZF64 300
150 22334BK;H2334 92 ZF34 150
180 22336BK;H2336 96 ZF36 160
210 22338BK;H2338 100 ZF38 170
240 22340BK;H2340 104 ZF40 180
300 22344BK;H2344 109 ZF44 200
370 22348BK;H2348 116 ZF48 220
460 22352BK;H2352 123 ZF52 240
560 22356BK;H2356 130 ZF56 260
45
Plummer Blocks SD30SD30G
For heavy load, double rubber sealed type / For bearing with adapter assembly
N
t
N1
J1 A1 H2
S
H
J H1
L
d1 150450mm
Shaft Bearing numbers 1 Abutment and fillet dimensions Approx.

dia.
mm mm
nominal nominal
number number
150 SD3034 SD3034G 260 160 450 110 32 42 230 540 200 50 320 77 M24 M30
160 SD3036 SD3036G 280 170 470 120 32 42 250 560 220 50 340 84 M24 M30
170 SD3038 SD3038G 290 170 470 120 32 42 250 560 220 50 345 85 M24 M30
180 SD3040 SD3040G 310 180 510 140 32 52 270 620 250 60 360 92 M24 M30
200 SD3044 SD3044G 340 200 570 160 35 55 290 700 280 65 400 100 M30 M30
220 SD3048 SD3048G 360 210 610 170 35 55 300 740 290 65 420 102 M30 M30
240 SD3052 SD3052G 400 240 680 190 40 60 340 820 320 70 475 114 M30 M36
260 SD3056 SD3056G 420 250 710 200 42 62 350 860 340 85 500 116 M36 M36
280 SD3060 SD3060G 460 280 770 210 42 62 360 920 350 85 550 128 M36 M36
300 SD3064 SD3064G 480 280 790 210 42 62 380 940 360 85 560 131 M36 M36
380 SD3080 SD3080G 600 365 960 270 57 77 430 1 140 420 120 710 158 M42 M48
400 SD3084 SD3084G 620 375 980 270 57 77 430 1 160 420 120 735 160 M42 M48
410 SD3088 SD3088G 650 390 1 040 280 57 77 460 1 220 450 125 765 167 M42 M48
430 SD3092 SD3092G 680 405 1 040 310 57 77 470 1 220 460 130 790 173 M42 M48
450 SD3096 SD3096G 700 415 1 100 320 57 77 485 1 270 470 130 820 175 M42 M48
1 SD3068, SD3072 and SD3076 are respectively identical to SD3368, SD3372 3Dimension Y is an approximate distance from the bearing center to the shaft
and SD3376 in terms of dimensions. For this reason, specify "SD3368," end for shaft end configuration.
"SD3372" or "SD3376" when ordering SD3068, SD3072 or SD3076.
2 Dimension g represents the bearing seat width for free-side bearing. Dimension NOTE: 1) Fill and drain plugs:
for fixed-side (code G) is 0.5 mm greater than the bearing width dimension. Size: PT3/8
46
A
g A/2
Y
d1 D

number dia.
bearings Y3 d1
(approx.)
70 23034BK;H3034 66 ZF34 150
80 23036BK;H3036 70 ZF36 160
85 23038BK;H3038 72 ZF38 170
100 23040BK;H3040 76 ZF40 180
130 23044BK;H3044 79 ZF44 200
150 23048BK;H3048 84 ZF48 220
210 23052BK;H3052 90 ZF52 240
240 23056BK;H3056 95 ZF56 260
300 23060BK;H3060 105 ZF60 280
320 23064BK;H3064 108 ZF64 300
620 23080BK;H3080 131 GS80 380
690 23084BK;H3084 132 GS84 400
800 23088BK;H3088 144 GS88 410
870 23092BK;H3092 147 GS92 430
980 23096BK;H3096 148 GS96 450
47
For heavy load, double sealed type / For bearing with adapter assembly
N
t
N1
J1 A1 H2
S
H
J H1
L
d1 150400mm
Shaft Bearing numbers 1 Abutment and fillet dimensions Approx.

dia.
mm mm
nominal nominal
number number
150 SD3134 SD3134G 280 170 470 120 35 42 250 560 220 50 340 98 M24 M30
160 SD3136 SD3136G 300 180 520 140 35 52 270 630 250 55 365 106 M30 M30
170 SD3138 SD3138G 320 190 560 140 35 55 310 680 270 55 385 114 M30 M30
180 SD3140 SD3140G 340 200 570 160 35 55 310 700 280 65 400 122 M30 M30
200 SD3144 SD3144G 370 225 640 180 40 60 320 780 310 70 450 130 M30 M36
220 SD3148 SD3148G 400 240 680 190 40 60 330 820 320 70 475 138 M30 M36
240 SD3152 SD3152G 440 260 740 200 42 62 360 880 350 85 515 154 M36 M36
260 SD3156 SD3156G 460 280 770 210 42 62 360 920 350 85 550 156 M36 M36
280 SD3160 SD3160G 500 300 830 230 50 70 390 990 380 100 590 170 M36 M42
300 SD3164 SD3164G 540 325 890 250 50 70 430 1 060 400 100 640 186 M36 M42
340 SD3172 SD3172G 600 365 960 310 57 77 470 1 140 460 120 710 202 M42 M48
360 SD3176 SD3176G 620 375 980 320 57 77 500 1 160 490 120 735 204 M42 M48
380 SD3180 SD3180G 650 390 1 040 340 57 77 520 1 220 510 125 765 210 M42 M48
400 SD3184 SD3184G 700 420 1 070 380 57 77 560 1 250 550 135 820 234 M42 M48
1 SD3168 is identical to SD3468 in terms of dimensions. For this reason, specify 3Dimension Y is an approximate distance from the bearing center to the shaft
"SD3468" when ordering SD3168. end for shaft end configuration.
2 Dimension g represents the bearing seat width for free-side bearing.
Dimension for fixed-side (code G) is 0.5 mm greater than the bearing width NOTE: 1) Fill and drain plugs:
dimension. Size: PT3/8
48
A
g A/2
Y
d1 D

number dia.
bearings Y3 d1
(approx.)
75 23134BK;H3134 76 ZF34 150
94 23136BK;H3136 81 ZF36 160
110 23138BK;H3138 86 ZF38 170
130 23140BK;H3140 91 ZF40 180
180 23144BK;H3144 96 ZF44 200
210 23148BK;H3148 102 ZF48 220
240 23152BK;H3152 112 ZF52 240
310 23156BK;H3156 115 ZF56 260
400 23160BK;H3160 124 ZF60 280
480 23164BK;H3164 135 ZF64 300
630 23172BK;H3172 159 GS72 340
850 23176BK;H3176 162 GS76 360
960 23180BK;H3180 167 GS80 380
1 080 23184BK;H3184 187 GS84 400
49
Heavy load, stepped bore type / For cylindrical bore bearing
N
t
N1
J1 A1 H2
S
H
J H1
L
d1 170320mm
Shaft Bearing numbers Abutment and fillet dimensions Approx.

dia.
mm mm mm
d d2 d3 free side fixed side D H J J1 N1 N A L A1 H1 H2 g1 t S
nominal nominal
number number
170 160 190 SD234 SD234G 310 180 510 140 32 52 270 620 230 60 360 96 M24 M30
180 170 200 SD236 SD236G 320 190 540 150 32 52 280 650 240 60 380 96 M24 M30
190 180 210 SD238 SD238G 340 200 570 160 35 55 290 700 260 65 400 102 M30 M30
200 190 220 SD240 SD240G 360 210 610 170 35 55 300 740 270 65 420 108 M30 M30
220 210 240 SD244 SD244G 400 240 680 190 40 60 330 820 300 70 475 118 M30 M36
240 230 260 SD248 SD248G 440 260 740 200 42 62 340 880 310 85 515 130 M36 M36
260 250 280 SD252 SD252G 480 280 790 210 42 62 370 940 340 85 560 140 M36 M36
280 260 300 SD256 SD256G 500 300 830 230 50 70 390 990 370 100 590 140 M36 M42
300 280 320 SD260 SD260G 540 325 890 250 50 70 410 1 060 390 100 640 150 M36 M42
320 300 340 SD264 SD264G 580 355 930 270 57 77 440 1 110 420 110 690 160 M42 M48
170 160 190 SD334 SD334G 360 210 610 170 35 55 300 740 270 65 420 130 M30 M30
180 170 200 SD336 SD336G 380 225 640 180 40 60 320 780 290 70 450 136 M30 M36
190 180 210 SD338 SD338G 400 240 680 190 40 60 330 820 300 70 475 142 M30 M36
200 190 220 SD340 SD340G 420 250 710 200 42 62 350 860 320 85 500 148 M36 M36
220 210 240 SD344 SD344G 460 280 770 210 42 62 360 920 330 85 550 155 M36 M36
240 230 260 SD348 SD348G 500 300 830 230 50 70 390 990 370 100 590 165 M36 M42
260 250 280 SD352 SD352G 540 325 890 250 50 70 410 1 060 390 100 640 175 M36 M42
280 260 300 SD356 SD356G 580 355 930 270 57 77 440 1 110 420 110 690 185 M42 M48
1 Dimension g represents the bearing seat width for free-side bearing. NOTE: 1) Fill and drain plugs:
Dimension for fixed-side (code G) is 0.5 mm greater than the bearing width Size: PT3/8
dimension.
2 Dimension Y is an approximate distance from the bearing center to the shaft
50
A
g A/2
Y
d2 d d3 D
Mass Nominal number Approx. Seal number shaft

dia.
bearings nut washer Y2 (d2) (d3) d
(approx.)
95 22234B AN34 AW34 75 ZF36 ZF42 170
110 22236B AN36 AW36 76 ZF38 ZF44 180
130 22238B AN38 AW38 80 ZF40 ZF46 190
150 22240B AN40 AW40 84 ZF42 ZF48 200
210 22244B AN44 AL44 90 ZF46 ZF52 220
240 22248B AN48 AL44 98 GS50 ZF56 240
320 22252B AN52 AL52 105 ZF54 ZF60 260
370 22256B AN56 AL52 107 ZF56 ZF64 280
460 22260B AN60 AL60 114 ZF60 ZF68 300
560 22264B AN64 AL64 122 ZF64 GS72 320
150 22334B AN34 AW34 92 ZF36 ZF42 170
180 22336B AN36 AW36 96 ZF38 ZF44 180
210 22338B AN38 AW38 100 ZF40 ZF46 190
240 22340B AN40 AW40 104 ZF42 ZF48 200
300 22344B AN44 AL44 109 ZF46 ZF52 220
370 22348B AN48 AL44 116 GS50 ZF56 240
460 22352B AN52 AL52 123 ZF54 ZF60 260
560 22356B AN56 AL52 130 ZF56 ZF64 280
51
Plummer Blocks SV5
Unit type standard / For bearing with adapter assembly
N N
N1
N1 J1 A1 H2
S
H
J H1
L
d1 20135mm
Shaft Bearing BAS code 2 Nominal number Abutment and fillet dimensions
dia. numbers
mm self-aligning spherical roller mm
d1 main cover ball bearings bearings D H J J1 N1 N L A A1
body
1205K
20 SV505 V052 052C 2205K 52 45 130 16 20 165 73 46
1206K
25 SV506 V062 062C 2206K 62 50 150 16 20 185 80 52
1207K
30 SV507 V072 072C 2207K 72 56 150 16 20 185 85 52
1208K
35 SV508 V080 080C 2208K 22208CK 80 60 170 16 20 205 95 60
1209K
40 SV509 V085 085C 2209K 22209CK 85 63 170 16 23 205 98 60
1210K
45 SV510 V090 090C 2210K 22210CK 90 67 170 16 23 205 100 60
1211K
50 SV511 V100 100C 2211K 22211BK 100 71 210 16 23 255 106 70
1212K
55 SV512 V110 110C 2212K 22212BK 110 80 210 21 25 255 112 70
1213K
60 SV513 V120 120C 2213K 22213BK 120 85 230 21 25 275 118 80
1215K
65 SV515 V130 130C 2215K 22215BK 130 90 230 21 25 280 118 80
1216K
70 SV516 V140 140C 2216K 22216BK 140 100 260 25 30 315 136 90
1217K
75 SV517 V150 150C 2217K 22217BK 150 100 260 25 30 315 140 90
1218K
80 SV518 V160 160C 2218K 22218BK 160 112 290 25 30 345 150 100
23218BK
1219K
85 SV519 V170 170C 2219K 22219BK 170 112 290 25 30 345 165 100
1220K
90 SV520 V180 180C 2220K 22220BK 180 125 320 56 23 32 380 170 110
23220BK
1222K
100 SV522 V200 200C 2222K 22222BK 200 132 350 60 23 32 410 190 120
23222BK
22224BK
110 SV524 V215 215C 23224BK 215 140 350 60 23 32 410 190 120
22226BK
115 SV526 V230 230C 23226BK 230 150 380 65 23 32 450 200 130
22228BK
125 SV528 V250 250C 23228BK 250 160 420 80 23 32 500 218 150
22230BK
135 SV530 V270 270C 23230BK 270 170 450 92 29 42 540 236 160
1 The numeral in nominal number of the setting ring represents the outside NOTE: 1) Sizes SV520 and greater are equipped with lifting eye bolts.
diameter and width dimension. 2) Dimension X indicates a deviation of the bearing center relative to the
2 The Japan Bearing Industrial Association Standard plummer block center, and its value is 1/2 the width of the setting
3 Dimension Y is an approximate distance from the bearing center to the shaft washer.
end for shaft end configuration. 3) An adaptor for bearing series 12, series H2 as well as series H3 can be
used.
52
Plummer Blocks SV5
A
g
A2
Y
d1 D
x x
Abutment and fillet dimensions Mass Nominal number Approx. Seal shaft
number dia.
mm Approx. kg Adapter setting mm mm
g A2 H1 H2 S washer 1 Y3 d1
nominal
number number number
H205X SR 52X 6 2 17
27 31 22 85 M14 2 2.1 H305X SR 52X 9 1 19 ZF5 20
H206X SR 62X 7 2 18
30 34 22 95 M14 2 2.7 H306X SR 62X10 1 20 ZF6 25
H207X SR 72X 8 2 19
33 37.5 22 106 M14 2 3.3 H307X SR 72X10 1 22 ZF7 30
H208X SR 80X 9.5 2 21
37 40.5 25 118 M14 2 4.5 H308X SR 80X 7 2 23 ZF8 35
H209X SR 85X10 2 22
39 42.5 25 125 M14 2 4.5 H309X SR 85X 8 2 24 ZF9 40
H210X SR 90X 9.5 2 24
39 42.5 25 128 M14 2 4.8 H310X SR 90X 8 2 25 ZF10 45
H211X SR100X10.5 2 25
42 47 28 140 M14 2 5.8 H311X SR100X 8.5 2 27 ZF11 50
H212X SR110X12 2 26
46 47 30 155 M18 2 6.8 H312X SR110X 9 2 29 ZF12 55
H213X SR120X13 2 28
49 50 30 165 M18 2 9.5 H313X SR120X 9 2 32 ZF13 60
H215X SR130X12.5 2 30
50 50 30 175 M18 2 10 H315X SR130X 9.5 2 33 ZF15 65
H216X SR140X15 2 32
56 58 32 195 M22 2 14 H316X SR140X11.5 2 36 ZF16 70
H217X SR150X14 2 34
56 60 32 195 M22 2 15 H317X SR150X10 2 38 ZF17 75
H218X SR160X16 2 35
62 65 35 224 M22 2 20 H318X SR160X11 2 40 ZF18 80
H2318X SR160X 9.6 1 46
H219X SR170X15 2 37
62 72.5 35 224 M22 2 20 H319X SR170X 9.5 2 43 ZF19 85
H220X SR160X18 2 39
70 75 40 243 M20 4 26 H320X SR180X12 2 45 ZF20 90
H2320X SR180X 9.7 1 52
H222X SR200X22 2 42
82 82 45 265 M20 4 30 H322X SR200X14.5 2 50 ZF22 100
H2322X SR200X12.2 1 58
H3124X SR215X12 2 53
82 82 45 280 M20 4 36 H2324X SR215X 6 1 62 ZF24 110
H3126 SR230X11 2 57
86 87 50 300 M20 4 45 H2326 SR230X 6 1 65 ZF26 115
H3128 SR250X13 2 60
94 96 50 315 M20 4 53 H2328 SR250X 6 1 70 ZF28 125
H3130 SR270X15 2 65
103 105 60 335 M24 4 63 H2330 SR270X 7 1 76 ZF30 135
4) Fill and drain plugs:
Size: SV505-SV520PT1/8
SV522-SV532PT1/4
5) When wanting a plummer block whose bore at the shaft end side is closed,
add code M1 after the plummer block nominal number.
53
Plummer Blocks SV5
Unit type standard / For bearing with adapter assembly
N1
J1 A1 H2
S
H
J H1
L
d1 140300mm
Shaft Bearing BAS code 2 Nominal number Abutment and fillet dimensions
dia. numbers
mm self-aligning spherical roller mm
d1 main cover ball bearings bearings D H J J1 N1 N L A A1
body nominal nominal
number number
22232BK
140 SV532 V290 290C 23232BK 290 190 470 92 29 50 560 250 170
22234BK
150 SV534 V310 310C 23234BK 310 200 560 92 29 50 660 258 180
22236BK
160 SV536 V320 320C 23236BK 320 200 560 92 29 50 660 258 180
22238BK
170 SV538 V340 340C 23238BK 340 212 580 104 33 54 680 300 190
22240BK
180 SV540 V360 360C 23240BK 360 224 610 130 33 54 740 300 224
22244BK
200 SV544 V400 400C 23244BK 400 250 680 148 36 60 820 330 250
22248BK
220 SV548 V440 440C 23248BK 440 280 740 166 40 66 880 340 280
22252BK
240 SV552 V480 480C 23252BK 480 300 790 180 43 72 940 370 300
22256BK
260 SV556 V500 500C 23256BK 500 315 830 190 43 72 990 390 315
22260BK
280 SV560 V540 540C 23260BK 540 335 890 200 46 78 1 060 410 335
22264BK
300 SV564 V580 580C 23264BK 580 355 930 215 49 84 1 110 440 355
end for shaft end configuration. 3) An adaptor for bearing series 12, series H2 as well as series H3 can be
used.
54
Plummer Blocks SV5
A
g A2
Y
d1 D
x x
Abutment and fillet dimensions Mass Nominal number Approx. Seal shaft
number dia.
mm Approx. kg Adapter setting mm mm
g A2 H1 H2 S washer 1 Y3 d1
nominal
H3132 SR290X16.5 2 71
113 112 60 375 M24 4 76 H2332 SR290X 9 1 83 ZF32 140
H3134 SR310X18 2 75
122 116 65 405 M24 4 89 H2334 SR310X12 1 87 ZF34 150
H3136 SR320X18 2 76
122 116 65 405 M24 4 100 H2336 SR320X10 1 89 ZF36 160
H3138 SR340X19 2 80
130 137 65 425 M27 4 110 H2338 SR340X10 1 94 ZF38 170
H3140 SR360X20 2 84
138 136 85 450 M27 4 130 H2340 SR360X10 1 99 ZF40 180
H3144 SR400X23 2 90
154 151 95 500 M30 4 196 H2344 SR400X10 1 108 ZF44 200
H3148 SR440X25 2 98
170 156 100 560 M33 4 260 H2348 SR440X10 1 118 ZF48 220
H3152 SR480X27 2 105
184 173 105 600 M36 4 318 H2352 SR480X10 1 127 ZF52 240
H3156 SR500X28 2 107
186 185 110 630 M36 4 336 H2356 SR500X10 1 130 ZF56 260
H3160 SR540X31 2 114
202 196 115 670 M39 4 433 H2360 SR540X10 1 160 ZF60 280
H3164 SR580X34 2 122
218 211 120 710 M42 4 507 H2364 SR580X10 1 151 ZF64 300

SV522-SV532PT1/4
55
Plummer Blocks SV2
Unit type, stepped bore type / For cylindrical bore bearing
N N
N1
N1 J1 A1 H2
S
H
J H1
L
d1 25110mm
Shaft dia. Bearing BAS code 2 Nominal number Abutment and fillet dimensions
numbers
mm Self-aligning spherical roller mm
d d2 d3 main cover ball bearings bearings D H J J1 N1 N L A A1
body
1205
25 20 30 SV205 V052 052C 2205 52 45 130 16 20 165 73 46
1206
30 25 35 SV206 V062 062C 2206 62 50 150 16 20 185 80 52
1207
35 30 45 SV207 V072 072C 2207 72 56 150 16 20 185 85 52
1208
40 35 50 SV208 V080 080C 2208 22208C 80 60 170 16 20 205 95 60
1209
45 40 55 SV209 V085 085C 2209 22209C 85 63 170 16 23 205 98 60
1210
50 45 60 SV210 V090 090C 2210 22210C 90 67 170 16 23 205 100 60

55 50 65 SV211 V100 100C 1211 22211B 100 71 210 16 23 255 106 70
2211 22211E

60 55 70 SV212 V110 110C 1212 22212B 110 80 210 21 25 255 112 70
2212 22212E

65 60 75 SV213 V120 120C 1213 22213B 120 85 230 21 25 275 118 80
2213 22213E

70 60 80 SV214 V125 125C 1214 22214B 125 90 230 21 25 280 118 80
2214 22214E

75 65 85 SV215 V130 130C 1215 22215B 130 90 230 21 25 280 118 80
2215 22215E

80 70 90 SV216 V140 140C 1216 22216B 140 100 260 25 30 315 136 90
2216 22216E

85 75 95 SV217 V150 150C 1217 22217B 150 100 260 25 30 315 140 90
2217 22217E

1218 22218B
90 80 100 SV218 V160 160C 2218 23218B 160 112 290 25 30 345 150 100
23218E
1219
95 85 110 SV219 V170 170C 2219 22219B 170 112 290 25 30 345 165 100

100 90 115 SV220 V180 180C 1220 22220B 180 125 320 56 23 32 380 170 110
2220 23220B

110 100 125 SV222 V200 200C 1222 22222B 200 132 350 60 23 32 410 190 120
2222 23222B
56
Plummer Blocks SV2
A
g A2
Y
d2 d d3 D
x x
Abutment and fillet dimensions Mass Nominal number Approx. Seal number shaft
dia.
mm Approx. kg setting mm mm
g A2 H1 H2 S washer 1 nut washer Y3 (d2) (d3) d1
nominal
SR 52X 6 2 17
27 31 22 85 M14 2 2.0 SR 52X 9 1 AN05 AW05 19 ZF 5 ZF 7 25
SR 62X 7 2 18
30 34 22 95 M14 2 2.6 SR 62X10 1 AN06 AW06 20 ZF 6 ZF 8 30
SR 72X 8 2 19
33 37.5 22 106 M14 2 3.1 SR 72X10 1 AN07 AW07 22 ZF 7 ZF10 35
SR 80X 9.5 2 21
37 40.5 25 118 M14 2 4.3 SR 80X 7 2 AN08 AW08 23 ZF 8 ZF11 40
SR 85X10 2 22
39 42.5 25 125 M14 2 4.3 SR 85X 8 2 AN09 AW09 24 ZF 9 ZF12 45
SR 90X 9.5 2 24
39 42.5 25 128 M14 2 4.6 SR 90X 8 2 AN10 AW10 25 ZF10 ZF13 50
42 47 28 140 M14 2 5.5 SR100X10.5 2 AN11 AW11 25 ZF11 ZF15 55

SR100X 8.5 2 27
46 47 30 155 M18 2 6.5 SR110X12 2 AN12 AW12 26 ZF12 ZF16 60

SR110X 9 2 29
49 50 30 165 M18 2 9.5 SR120X13 2 AN13 AW13 28 ZF13 ZF17 65

SR120X 9 2 32
50 50 30 175 M18 2 10 SR125X13 2 AN14 AW14 28 ZF13 ZF18 70

SR125X 9.5 2 32
50 50 30 175 M18 2 10 SR130X12.5 2 AN15 AW15 30 ZF15 ZF19 75

SR130X 9.5 2 33
56 58 32 195 M22 2 14 SR140X15 2 AN16 AW16 32 ZF16 ZF20 80

SR140X11.5 2 36
56 60 32 195 M22 2 15 SR150X14 2 AN17 AW17 34 ZF17 ZF21 85

SR150X10 2 38
SR160X15 2 35
62 65 35 224 M22 2 20 SR160X11 2 AN18 AW18 40 ZF18 ZF22 90
SR160X 9.6 1 46
SR170X15 2 37
62 72.5 35 224 M22 2 20 SR170X 9.5 2 AN19 AW19 43 ZF19 ZF24 95
SR180X18 2 39
70 75 40 243 M20 4 26 SR180X12 2 AN20 AW20 45 ZF20 ZF26 100
SR180X 9.7 1 52
SR200X22 2 42
82 82 45 265 M20 4 30 SR200X14.5 2 AN22 AW22 50 ZF22 ZF28 110
SR200X12.2 1 58
SV222-SV232PT1/4
57
Plummer Blocks SV2
Unit type, stepped bore type / For cylindrical bore bearing
N1
J1 A1 H2
S
H
J H1
L
d1 120320mm
Shaft dia. Bearing BAS code 2 Nominal number Abutment and fillet dimensions
numbers
mm Self-aligning spherical roller mm
d d2 d3 main cover ball bearings bearings D H J J1 N1 N L A A1
body
22224B
120 110 135 SV224 V215 215C 23224B 215 140 350 60 23 32 410 190 120
22226B
130 115 145 SV226 V230 230C 23226B 230 150 380 65 23 32 450 200 130
22228B
140 125 155 SV228 V250 250C 23228B 250 160 420 80 23 32 500 218 150
22230B
150 135 165 SV230 V270 270C 23230B 270 170 450 92 29 42 540 236 160
22232B
160 140 175 SV232 V290 290C 23232B 290 190 470 92 29 50 560 250 170
22234B
170 150 190 SV234 V310 310C 23234B 310 200 560 92 29 50 660 258 180
22236B
180 160 200 SV236 V320 320C 23236B 320 200 560 92 29 50 660 258 180
22238B
190 170 210 SV238 V340 340C 23238B 340 212 580 104 33 54 680 300 190
200 180 230 SV240 V360 360C 22240B 360 224 610 130 33 54 740 300 224
220 200 250 SV244 V400 400C 22244B 400 250 680 148 36 60 820 330 250
240 220 260 SV248 V440 440C 22248B 440 280 740 166 40 66 880 340 280
260 240 280 SV252 V480 480C 22252B 480 300 790 180 43 72 940 370 300
280 260 300 SV256 V500 500C 22256B 500 315 830 190 43 72 990 390 315
300 280 320 SV260 V540 540C 22260B 540 335 890 200 46 78 1 060 410 335
320 300 340 SV264 V580 580C 22264B 580 355 930 215 49 84 1 110 440 355
58
Plummer Blocks SV2
A
g A2
Y
d2 d d3 D
x x
Abutment and fillet dimensions Mass Nominal number Approx. Seal number shaft
dia.
mm Approx. kg setting mm mm
g A2 H1 H2 S washer 1 nut washer Y3 (d2) (d3) d1
nominal
SR215X12 2 53
82 82 45 280 M20 4 36 SR215X 6 1 AN24 AW24 62 ZF24 ZF30 120
SR230X11 2 57
86 87 50 300 M20 4 44 SR230X 6 1 AN26 AW26 65 ZF26 GS33 130
SR250X13 2 60
94 96 50 315 M20 4 52 SR250X 6 1 AN28 AW28 70 ZF28 GS35 140
SR270X15 2 65
103 105 60 335 M24 4 62 SR270X 7 1 AN30 AW30 76 ZF30 GS37 150
SR290X16.5 2 71
113 112 60 375 M24 4 75 SR290X 9 1 AN32 AW32 83 ZF32 GS39 160
SR310X18 2 75
122 116 65 405 M24 4 87 SR310X12 1 AN34 AW34 87 ZF34 ZF42 170
SR320X18 2 76
122 116 65 405 M24 4 98 SR320X10 1 AN36 AW36 89 ZF36 ZF44 180
SR340X19 2 80
130 137 65 425 M27 4 110 SR340X10 1 AN38 AW38 94 ZF38 ZF46 190
138 136 85 450 M27 4 130 SR360X20 2 AN40 AW40 84 ZF40 GS50 200
154 151 95 500 M30 4 196 SR400X23 2 AN44 AL44 90 ZF44 ZF54 220
170 156 100 560 M33 4 260 SR440X25 2 AN48 AL44 98 ZF48 ZF56 240
184 173 105 600 M36 4 318 SR480X27 2 AN52 AL52 105 ZF52 ZF60 260
186 185 110 630 M36 4 336 SR500X28 2 AN56 AL52 107 ZF56 ZF64 280
202 196 115 670 M39 4 433 SR540X31 2 AN60 AL60 114 ZF60 ZF68 300
218 211 120 710 M42 4 507 SR580X34 2 AN64 AL64 122 ZF64 GS72 320

SV222-SV232PT1/4
59
Plummer Blocks
Specialized Plummer Block
960
950
1200
1660
1130
1200
280
2750
1100
Fixed side
960
950
1660
1130
1200
1200
280
2750 1100
Free side
Fixed side: 0S23601GN1Y545ZX1

Number
Free side: 0S23602N1Y545ZX1
Bearing 2401180BK30
Application Tube dryer
RPM 612rpm
Lubricating system Circulating oil
60
Plummer Blocks
490
194
620
380
450
360
765
375
120
1000
Fixed side
520
204 380
450
360
620
765
375
120
1000
Free side
Fixed side: 1S7642GY851ZX1

Number
Free side: 1S7642M1Y851ZX1
Bearing 23176BK+AH3176H
Application Sintering m
RPM 34rpm
Lubricating system Grease lubrication
61
Plummer Blocks
168
63
Fixed side
100
200
244
Free side
125
50
420
Fixed side: 2S22B32GX1

Number
Free Side: 2S22B32
Bearing 2222KC3+H322X
Application Pump flywheel
RPM 1 480rpm
Lubricating system Oil bath
312
162 150
150
Fixed side
200
220
240
340
425
Free side
212
65
610
Fixed side: 0S4483Y892GX1ZX1

Number
Free side: 0S4483Y892ZX1
Bearing TS3-23044BF3C4+ANL44, ALL44

Application ID dryer
RPM 8rpmMAX
Lubricating system Oil bath
62
Plummer Blocks
200
70 20
67
20
D5
PC
190
150
185
260
280
580
Water cooled, fixed side
235
70 20
30
PC
D5
20
280
295
580
150
195
Water cooled, free side
Fixed side: FY3475GY133ZX1

Number
Free side: FY3460M1Y133ZX1
Fixed side: TS3-23034BKC4+H3034
Bearing
Free side: TS2-R3431KC4+H9180
Application CAPL
RPM 90rpm
Lubricating system Grease lubrication
63

Plummer Block

Uploaded by

Copyright:

Available Formats

Plummer Block

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Plummer Block

Uploaded by

Copyright:

Available Formats

For New Technology Network

CAT. NO. 2500/E

NTN Corporation. 1998

Technical Data 332

Split type 3451

Index of Bearing Tables

Unit type 5259

Specialized Plummer Blocks 6063

2. Plummer Block and Rolling Bearing Tolerances 4

3. Plummer Block and Bearing Materials13

4. Strength of Plummer Blocks, and Combination with Bearings15

9. Handling the Plummer Blocks and Bearings 24

Tightening bolt Oil fill plug

Self-aligning rolling bearing

Mounting bolt holes

Plummer block unit Knock ball

Products painted in user-specified colors s

2. Plummer Block and Rolling Bearing Tolerances

2.1 Plummer block tolerances

Table 2.1 Tolerances of plummer blocks Unit: mm

Table 2.2 Tolerances of length of cast iron components Unit: mm

1.5 2.0 3.0 4.0 6.0

Table 2.3 Bore dimensions and tolerances

Table 2.4 (1) Dimensions and tolerances of locating rings

Table 2.4 (2) Dimensions and tolerances of locating rings

2.2 Machining tolerances of mounting bolt seat

L: Basic casting dimension (as cast dimension)

Table 2.6 Tolerances of dimension L after machining of

2.3 Rolling bearing accuracies

Table 2.7 Bearing tolerances

(2) Tolerances of outer rings (JIS class 0) Unit: m

(3) Tolerance and allowable values (JIS class 0)

2.4 Rolling bearing internal clearance

Table 2.8 Radial internal clearance of self-aligning ball bearings

Nominal bore diameter Clearance

(2) Data for tapered bore bearings Unit: m

Nominal bore diameter Clearance

Table 2.9 Radial internal clearance of self-aligning roller bearings

Nominal bore diameter Clearance

(2) Data for tapered bore bearing Unit: m

Nominal bore diameter Clearance

3. Plummer Block and Bearing Materials

3.1 Plummer block materials

Table 3.1 Mechanical properties

(2) Mechanical properties of spheroidal graphite cast iron

Type Symbol Tensile test Impact test

Proof stress Tensile strength Elongation Charpy absorption energy

(3) Mechanical properties of carbon cast steel

Type Symbol Yield point Tensile test

Tensile strength Elongation Reduction in area

Table 3.2 Plummer block accessories materials

Accessory Material used Symbol Applicable JIS standard

3.2 Bearing materials

Table 3.3 Adapter materials

4. Strength of Plummer Blocks, and Combination with Bearings

4.2 Combinations of plummer blocks and bearings

Table 4.2 (1) Plummer blocks and applicable bearings

Table 4.2 (2) Plummer blocks and applicable bearings

SV6 05K22K 05K22K 08CK22K 08CK22K

SV3 0522 0522 08C22 08C56B