ORDER NO.

DSC1102004CE
B26

Digital Camera
Model No. DMC-FS35EB
DMC-FS35EE
DMC-FS35EF
DMC-FS35EG
DMC-FS35EP
DMC-FH25P
DMC-FH25PC
DMC-FH25PR
DMC-FH25PU
DMC-FH25GA
DMC-FH25GC
DMC-FH25GF
DMC-FH25GH
DMC-FH25GK
DMC-FH25GN
DMC-FH25GT
DMC-FH24P
Vol. 1

Panasonic Corporation 2011 Unauthorized copy-

ing and distribution is a violation of law.
Colour [DMC-FH25]
[DMC-FS35] (S)...........Silver Type (except PC/PR/GT)
(S)...........Silver Type (except EF) (K)...........Black Type
(K)...........Black Type (R)...........Red Type (except PR/GT)
(R)...........Red Type (except EE) (A)...........Blue Type (only P/PC/PU/GK/GN)
(A)...........Blue Type (except EF) (V)...........Violet Type (only P/PC/PR/PU/GT)
(V)...........Violet Type (except EE/EF) [DMC-FH24]
(K)...........Black Type

TABLE OF CONTENTS
PAGE PAGE
1 Safety Precautions -----------------------------------------------3 8 Disassembly and Assembly Instructions -------------- 22
1.1. General Guidelines ----------------------------------------3 8.1. Disassembly Flow Chart ------------------------------- 22
1.2. Leakage Current Cold Check ---------------------------3 8.2. PCB Location --------------------------------------------- 22
1.3. Leakage Current Hot Check (See Figure 1.)--------3 8.3. Disassembly Procedure-------------------------------- 23
1.4. How to Discharge the E.Capacitor on Flash 8.4. Lens Disassembly Procedure ------------------------ 28
Top P.C.B. ----------------------------------------------------4 8.5. Assembly Procedure for the Lens ------------------- 32
2 Warning --------------------------------------------------------------5 8.6. Removal of the CCD Unit------------------------------ 38
2.1. Prevention of Electrostatic Discharge (ESD) 8.7. Removal of the Focus Motor-------------------------- 38
to Electrostatically Sensitive (ES) Devices ----------5 8.8. The Application of Grease Method------------------ 38
2.2. How to Recycle the Lithium Ion Battery (U.S. 9 Measurements and Adjustments -------------------------- 39
Only)-----------------------------------------------------------5 9.1. Introduction------------------------------------------------ 39
2.3. Caution for AC Cord(For EB/GC/GH) -----------------6 9.2. Before Disassembling the unit ----------------------- 39
2.4. How to Replace the Lithium Battery -------------------7 9.3. Details of Electrical Adjustment ---------------------- 41
3 Service Navigation------------------------------------------------8 9.4. After Adjustment ----------------------------------------- 45
3.1. Introduction --------------------------------------------------8 10 Maintenance------------------------------------------------------ 46
3.2. General Description About Lead Free Solder 10.1. Cleaning Lens and LCD Panel ----------------------- 46
(PbF) ----------------------------------------------------------8
3.3. Important Notice 1:(Other than U.S.A. and
Canadian Market) ------------------------------------------8
3.4. How to Define the Model Suffix (NTSC or PAL
model)---------------------------------------------------------9
4 Specifications ---------------------------------------------------- 13
5 Location of Controls and Components------------------ 14
6 Service Mode ----------------------------------------------------- 16
6.1. Error Code Memory Function ------------------------- 16
6.2. ICS (Indication of additional Camera Settings
when picture was taken) function -------------------- 18
7 Service Fixture & Tools --------------------------------------- 20
7.1. Service Fixture and Tools ------------------------------ 20
7.2. When Replacing the Main P.C.B. -------------------- 21
7.3. Service Position ------------------------------------------ 21

2
1 Safety Precautions
1.1. General Guidelines 1.3. Leakage Current Hot Check
1. IMPORTANT SAFETY NOTICE (See Figure 1.)
There are special components used in this equipment
1. Plug the AC cord directly into the AC outlet. Do not use
which are important for safety. These parts are marked by
an isolation transformer for this check.
2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F
in the Schematic Diagrams, Circuit Board Layout,
capacitor, between each exposed metallic part on the set
Exploded Views and Replacement Parts List. It is essen-
and a good earth ground, as shown in Figure 1.
tial that these critical parts should be replaced with manu-
3. Use an AC voltmeter, with 1 k/V or more sensitivity, to
facturers specified parts to prevent X-RADIATION,
measure the potential across the resistor.
shock, fire, or other hazards. Do not modify the original
4. Check each exposed metallic part, and measure the volt-
design without permission of manufacturer.
age at each point.
2. An Isolation Transformer should always be used during
5. Reverse the AC plug in the AC outlet and repeat each of
the servicing of AC Adaptor whose chassis is not isolated
the above measurements.
from the AC power line. Use a transformer of adequate
6. The potential at any point should not exceed 0.75 V RMS.
power rating as this protects the technician from acci-
A leakage current tester (Simpson Model 229 or equiva-
dents resulting in personal injury from electrical shocks. It
lent) may be used to make the hot checks, leakage cur-
will also protect AC Adaptor from being damaged by acci-
rent must not exceed 1/2 mA. In case a measurement is
dental shorting that may occur during servicing.
outside of the limits specified, there is a possibility of a
3. When servicing, observe the original lead dress. If a short
shock hazard, and the equipment should be repaired and
circuit is found, replace all parts which have been over-
rechecked before it is returned to the customer.
heated or damaged by the short circuit.
4. After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
5. After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.

1.2. Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the
two prongs on the plug.
2. Measure the resistance value, with an ohmmeter, Figure. 1
between the jumpered AC plug and each exposed metal-
lic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metal-
lic part has a return path to the chassis, the reading
should be between 1 M and 5.2 M. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.

3
1.4. How to Discharge the E.Capacitor on Flash Top P.C.B.
CAUTION:
1. Be sure to discharge the E.capacitor on FLASH TOP P.C.B..
2. Be careful of the high voltage circuit on FLASH TOP P.C.B. when servicing.

[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Install the insulation tube onto the lead part of resistor (ERG5SJ102:1k /5W).
(An equivalent type of resistor may be used.)
3. Place a resistor between both terminals of E.capacitor on the FLASH Top P.C.B. for approx. 5 seconds.
4. After discharging, confirm that the E.capacitor voltage is lower than 10V using a voltmeter.

Fig. F1

4
2 Warning
2.1. Prevention of Electrostatic Discharge (ESD) to Electrostatically
Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Elec-
trostatically Sensitive (ES) Devices.

The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).

1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as alumi-
num foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or compara-
ble conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) suf-
ficient to damage an ES device).

2.2. How to Recycle the Lithium Ion Battery (U.S. Only)

5
2.3. Caution for AC Cord 2.3.2.1. Important
The wires in this mains lead are coloured in accordance with
(For EB/GC/GH) the following code:
2.3.1. Information for Your Safety
IMPORTANT Blue Neutral
Your attention is drawn to the fact that recording of pre- Brown Live
recorded tapes or discs or other published or broadcast
As the colours of the wires in the mains lead of this appliance
material may infringe copyright laws.
may not correspond with the coloured markings identifying the
WARNING
To reduce the risk of fire or shock hazard, do not expose terminals in your plug, proceed as follows:
this equipment to rain or moisture.
CAUTION The wire which is coloured BLUE must be connected to the ter-
To reduce the risk of fire or shock hazard and annoying minal in the plug which is marked with the letter N or coloured
interference, use the recommended accessories only. BLACK.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER The wire which is coloured BROWN must be connected to the
To prevent electric shock, do not remove the cover. No user terminal in the plug which is marked with the letter L or coloured
serviceable parts inside. Refer servicing to qualified service RED.
personnel.
Under no circumstances should either of these wires be con-
2.3.2. Caution for AC Mains Lead nected to the earth terminal of the three pin plug, marked with
For your safety, please read the following text carefully. the letter E or the Earth Symbol.

This appliance is supplied with a moulded three-pin mains plug

for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the 2.3.2.2. Before Use
replacement fuse has a rating of 5 amperes and it is approved Remove the Connector Cover as follows.
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.

If the plug contains a removable fuse cover you must ensure

that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local 2.3.2.3. How to Replace the Fuse
Panasonic Dealer. 1. Remove the Fuse Cover with a screwdriver.

If the fitted moulded plug is unsuitable for the socket outlet in

your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.

If a new plug is to be fitted please observe the wiring code as

shown below.
If in any doubt, please consult a qualified electrician. 2. Replace the fuse and attach the Fuse cover.

6
2.4. How to Replace the Lithium Battery
2.4.1. Replacement Procedure
1. Remove the MAIN P.C.B.. (Refer to Disassembly Procedures.)
2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. B9101 at component side of MAIN
P.C.B.) and remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Type No. ML421 includes electric lead terminals.

NOTE:
This Lithium battery is a critical component.
(Type No.: ML421 Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.

NOTE:
Above caution is applicable for a battery pack which is for DMC-FS35, FH25, FH24 series, as well.

7
3 Service Navigation
3.1. Introduction
This service manual contains technical information, which allow service personnels to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.

3.2. General Description About Lead Free Solder (PbF)

The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30C (86F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used

Service caution for repair work using Lead Free Solder (PbF)
The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of PbF is printed on the P.C.B. using the lead free solder.)
To put lead free solder, it should be well molten and mixed with the original lead free solder.
Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 35030C
(66286F).
Recommended Lead Free Solder (Service Parts Route.)
The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%

3.3. Important Notice 1:(Other than U.S.A. and Canadian Market)

1. The service manual does not contain the following information because of issues servicing to component level without neces-
sary equipment/facilities.
a. Schematic diagram, Block Diagram and P.C.B. layout of MAIN P.C.B. and SUB P.C.B..
b. Parts list for individual parts for MAIN P.C.B. and SUB P.C.B..
When a part replacement is required for repairing MAIN P.C.B. and/or SUB P.C.B., replace as an assembled parts. (MAIN
P.C.B./SUB P.C.B.)
2. The following category is/are recycle module part. please send it/them to Central Repair Center.
MAIN P.C.B. (VEP56126C): Excluding replacement of Lithium Battery
SUB P.C.B. (VEP59094A)

8
3.4. How to Define the Model Suffix (NTSC or PAL model)
There are eight kinds of DMC-FS35, FH25, FH24, regardless of the colours.
a) DMC-FH24P
b) DMC-FH25P/PC
c) DMC-FS35EB/EF/EG/EP
d) DMC-FS35EE
e) DMC-FH25GT
f) DMC-FH25GK
g) DMC-FH25GN
h) DMC-FH25PR/PU/GA/GC/GF/GH
What is the difference is that the INITIAL SETTINGS data which is stored in Flash-ROM mounted on MAIN P.C.B..

3.4.1. Defining methods:

To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.

NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The service software is available at TSN Website. To download, click on Support Information from NWBG/VDBG-AVC.

9
3.4.2. INITIAL SETTINGS:
After replacing the MAIN P.C.B., be sure to perform the initial settings after achieving the adjustment by ordering the following pro-
cedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, be sure to read the following CAUTIONS.

2. PROCEDURES:
Precautions: Read the above "CAUTION 1" and "CAUTION 2", carefully.
Preparation:
- Attach the Battery or AC Adaptor with a DC coupler to the unit.
(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
1. Turn the Power on.
2. Press the [ MODE ] button, and select the [ NORMAL PICTURE ] mode by Cursor buttons, then press the
[ MENU/SET ] button.
3. Turn the Power off.
(If the unit is other than [ NORMAL PICTURE ] mode, it does not display the initial settings menu.)
Step 1. The temporary cancellation of INITIAL SETTINGS:
Set the [ REC ]/[ PLAYBACK ] selector switch to [ REC ] (Camera mark).
While pressing [ UP ] of Cursor button and [ E.ZOOM ] button simultaneously, turn the Power on.
Step 2. The cancellation of INITIAL SETTINGS:
Set the [ REC ]/[ PLAYBACK ] selector switch to [ PLAYBACK ].
Press [ UP ] of Cursor button and [ E.ZOOM ] button simultaneously, then turn the Power off.

The LCD displays the ! mark before the unit powers down.

Step 3. Turn the Power on:

Set the [ REC ]/[ PLAYBACK ] selector switch to [ REC ] (Camera mark), and then turn the Power on.
Step 4. Display the INITIAL SETTING:
While pressing [ MENU/SET ] and [ RIGHT ] of Cursor buttons simultaneously, turn the Power off.
The "INITIAL SETTINGS" menu is displayed.
There are two kinds of INITIAL SETTINGS menu form as follows:

10
 [CASE 1. After replacing MAIN P.C.B.]
When MAIN P.C.B. has just been replaced, all of the model suffix is displayed as follows. (Five pages in total)

[CASE 2. Other than After replacing MAIN P.C.B.]

Step 5. Choose the model suffix in INITIAL SETTINGS: (Refer to CAUTION 1)

[Caution: After replacing MAIN P.C.B.]
The model suffix can been chosen, JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can not be changed.
Therefore, select the area carefully.
Select the area with pressing [ UP ] / [ DOWN ] of Cursor buttons.

11
 Step 6. Chose the model number in INITIAL SETTINGS: (Only for P models.)
This step is necessary only for P.
Only for model suffix with P, there are two kind of model; (DMC-FH25 and DMC-FH24) ,due to difference of sales chan-
nel.Therefore, not only model suffix, but also model number (FH25 or FH24) has to be set up in the INITIAL SETTINGS. (The
FH25 is displayed as default status.)

When the model number is one of the "DMC-FH24P", change the model number with the following procedure:
Press the [E.ZOOM] button in order to change the indication from "FH25" into "FH24".
(Each time one presses the [E.ZOOM] button, model indication is changed from "FH25" to "FH24" (Toggle switch))

Step 7. Set the model suffix in INITIAL SETTINGS:

Press the [ RIGHT ] of Cursor buttons.
The only set area is displayed, and then press the [ RIGHT ] of Cursor buttons after confirmation.
(The unit is powered off automatically.)

Step 8. CONFIRMATION:
Confirm the display of PLEASE SET THE CLOCK in concernd language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the GT or GK model suffix is selected, the display shows PLEASE SET THE CLOCK in Chinese.)

1) As for your reference, major default setting condition is as shown in the following table.
Default setting (After INITIAL SETTINGS)
MODEL VIDEO OUTPUT LANGUAGE DATE REMARKS
a) DMC-FH25P/FH24P NTSC English Month/Date/Year
b) DMC-FS35EG PAL English Date/Month/Year
c) DMC-FH25PU NTSC Spanish Month/Date/Year
d) DMC-FH25GC PAL English Date/Month/Year
e) DMC-FH25GT NTSC Chinese (traditional) Year/Month/Date
f) DMC-FH25GK PAL Chinese (simplified) Year/Month/Date
g) DMC-FS35EF PAL French Date/Month/Year
h) DMC-FS35EB PAL English Date/Month/Year
i) DMC-FS35EE PAL Russian Date/Month/Year
j) DMC-FH25GN PAL English Date/Month/Year
k) DMC-FH25PC NTSC English Month/Date/Year
l) DMC-FH25PR PAL Spanish Date/Month/Year
m) DMC-FH25GH PAL English Date/Month/Year
n) DMC-FS35EP PAL English Date/Month/Year
o) DMC-FH25GF PAL English Date/Month/Year
p) DMC-FH25GA PAL English Date/Month/Year

12
4 Specifications

13
5 Location of Controls and Components
1 Flash 1 2 3
2 Lens
3 Self-timer indicator
AF Assist Lamp

4 LCD monitor 4 8 9 10
5 [MENU/SET] button
6 [DISP.] button
7 [Q.MENU] /Delete /Cancel
button
8 [MODE] button
9 [Rec]/[Playback] selector switch

5 6 7

10 Cursor buttons
: /Exposure compensation
: /Macro Mode
AF Tracking
: /Self-timer
: /Flash setting

11 Strap eyelet 11
Be sure to attach the strap when using
the camera to ensure that you will not 12
drop it.
12 Lens barrel
13 [AV OUT/DIGITAL] socket 13

14 Camera ON/OFF switch

15 Zoom lever
16 Speaker 14 15
Do not cover the speaker with your
fingers.
17 Microphone
18 Shutter button
19 [E.ZOOM] button
20 Tripod receptacle 1617 18 19
21 Card/Battery door
22 DC coupler cover 20 21
When using an AC adaptor, ensure that
the Panasonic DC coupler (optional) and
AC adaptor (optional) are used.

22

14
 Selecting the [Rec] Mode

Slide the [Rec]/[Playback]

selector switch to [
].

Press [MODE].

Press /// to select the

mode.

Press [MENU/SET].

List of [Rec] Modes

} Intelligent Auto Mode

The subjects are recorded using settings automatically selected by the camera.

Normal Picture Mode
The subjects are recorded using your own settings.
My Scene Mode
Pictures are taken using previously registered recording scenes.
Scene Mode
This allows you to take pictures that match the scene being recorded.
 Motion Picture Mode
This mode allows you to record motion pictures with audio.

15
6 Service Mode
6.1. Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly (i.e.,when the unit is powered on by the battery,
the battery is pulled out) The error code is memorized to FLASH-ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
Preparation:
1. Attach the Battery or AC Adaptor with a DC coupler to the unit.
NOTE:
*Since this unit has built-in memory, it can be performed without inserting SD memory card.
Step 1. The temporary cancellation of INITIAL SETTINGS:
Set the [ REC ]/[ PLAYBACK ] selector switch to [ REC ] (Camera mark).
While pressing [ UP ] of Cursor button and [ E.ZOOM ] button simultaneously, turn the Power on.
Step 2. Execute the error code display mode:
Press the [ LEFT ] of Cursor button, [ MENU/SET ] button and [ E.ZOOM ] button simultaneously.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display Error code display Operation history display Normal display .....

Example of Error Code Display

16
 3. Error Code List
The error code consists of 8 bits data and it shows the following information.

17
 Important notice about "Error Code List"
1) About "*" indication:
The third digit from the left is different as follows.
- In case of 0 (example: 18001000)
When the third digit from the left shows "0", this error occurred under the condition of INITIAL SETTINGS has been
completed.
It means that this error is occurred basically at user side.
- In case of 8 (example: 18801000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
2) About "?" indication: ("18*0 0?01" to "18*0 0?50"):
The third digit from the right shows one of the hexadecimal ("0" to "F") character.

4. How to exit from Error Code display mode:

Simply, turn the power off. (Since Error code display mode is executed under the condition of temporary cancellation of "INI-
TIAL SETTINGS", it wake up with normal condition when turn off the power.)
NOTE:
The error code can not be initialized.

6.2. ICS (Indication of additional Camera Settings when picture was taken)
function
1. General description
This unit is equipped with ICS (ICS: Indication of additional Camera Settings when picture was taken) function by playing back
the concerned picture on the LCD display.
(This function is achieved by utilizing "maker note" data stored in Exif data area of recorded picture file.)
To proceed failure diagnosis, use this ICS function together with "displaying the recorded picture with picture information "
function.
NOTE:
The ICS function operates with a picture which is only taken with the same model. (It may not be displayed when the picture
was taken with other model.)
Since Exif data is not available after the picture is edited by PC, the ICS function may not be activated.

2. How to display
The ICS data is displayed by ordering the following procedure:
Preparation:
1. Attach the Battery or AC Adaptor with a DC coupler to the unit.
NOTE:
Since this unit has bult-in memory, it can be performed without inserting SD memory card.
Step 1. The temporary cancellation of "INITIAL SETTINGS":
Set the [ REC ]/[ PLAYBACK ] selector switch to [ REC ] (Camera mark).
While pressing [ UP ] of Cursor button and [ E.ZOOM ] button simultaneously, turn the Power on.
Step 2. Execute the ICS display mode:
Set the [ REC ]/[ PLAYBACK ] selector switch to [ PLAYBACK ].
Select the concerned picture by pressing the [ LEFT ] and [ RIGHT ] of Cursor button.
Press the [ LEFT ] of Cursor button, [ MENU/SET ] button and [ E.ZOOM ] button simultaneously.
Press the [ DISP. ] button, 3 times.
The display condition is changed as shown below when the [ DISP. ] button is pressed.

Code display Code + Picture display (1) Code + Picture display (2) ICS display Code display .....

18
3. How to read

4. How to exit:
Simply, turn the power off. (Since ICS function is executed under the condition of temporary cancellation of
"INITIAL SETTINGS", it wake up with normal condition when turn off the power.)

19
7 Service Fixture & Tools
7.1. Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.

20
7.2. When Replacing the Main P.C.B.
After replacing the MAIN P.C.B., be sure to achieve adjustment.
The adjustment instruction is available at software download on the Support Information from NWBG/VDBG-AVC web-site in
TSN system, together with Maintenance software.

7.3. Service Position

This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No. Parts No. Connection Form
1 RFKZ0581 FP9001 (MAIN) - CCD UNIT 47PIN 0.3FFC
2 RFKZ0416 FP9002 (MAIN) - LENS UNIT 41PIN 0.3FFC
3 RFKZ0416 FP9003 (MAIN) - LCD UNIT 41PIN 0.3FFC
4 RFKZ0418 PP9001 (MAIN) - PS8001 (FLASH TOP) 30PIN B to B
5 RFKZ0553 PS9001 (MAIN) - PP9501 (SUB) 16PIN B to B

CAUTION-1. (When servicing FLASH TOP P.C.B.)

1. Be sure to discharge the E.capacitor on FLASH TOP P.C.B..
Refer to HOW TO DISCHARGE THE E.CAPACITOR ON FLASH TOP P.C.B..
The E.capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH TOP P.C.B..
3. DO NOT allow other parts to touch the high voltage circuit on FLASH TOP P.C.B..

21
8 Disassembly and Assembly Instructions
8.1. Disassembly Flow Chart
This is a disassembling chart.
When assembling, perform this chart conversely.

8.2. PCB Location

22
8.3. Disassembly Procedure 8.3.1. Removal of the Rear Case Unit and
Front Case Unit
No. Item Fig Removal
1 Rear Case Unit (Fig. D1) Card
Front Case Unit Battery
6 Screws (A)
3 Screws (B)
(Fig. D2) 2 Locking tabs
Rear Case Unit
2 Locking tabs
Front Case Unit
2 Sub P.C.B. (Fig. D3) PP9501(Connector)
Sub P.C.B.
3 LCD Unit (Fig. D4) 2 Locking tabs
PCB Spacer
MODE Knob
1 Screw (C)
FP9003(Flex)
(Fig. D5) LCD Unit
4 Top Case Unit (Fig. D6) 3 Screws (D)
Frame Plate
Tripod Fixing Plate
PS8001(Connector)
Top Case Unit
5 Flash Top P.C.B. (Fig. D7) 2 Locking tabs
AF Panel Light
2 Screws (E)
3 Locking tabs
Flash Top P.C.B.
2 Locking tabs
Speaker
Mic Damper
Power Knob Base
Power Knob
EZ Button
Top Ornament Unit
(Fig. D8) NOTE: (When installing)
6 Lens Unit (Fig. D9) DPR Sheet
FP9001(Flex)
FP9002(Flex)
(Fig. D1)
Lens Unit
7 Main P.C.B. (Fig. D10) 1 Screw (F)
1 Locking tab
Main P.C.B.
8 Battery Case (Fig. D11) 1 Locking tab
Battery Out Spring
Battery Case
9 Battery Door Unit (Fig. D12) Battery Door Shaft
Jack Door Battery Door Unit
Jack Door Shaft
Jack Door

23
 8.3.3. Removal of the LCD Unit

(Fig. D2)

8.3.2. Removal of the Sub P.C.B.

(Fig. D4)

(Fig. D3)

24
 8.3.5. Removal of the Flash Top P.C.B.

(Fig. D5)

8.3.4. Removal of the Top Case Unit

(Fig. D7)

(Fig. D6)

25
 8.3.6. Removal of the Lens Unit

(Fig. D9)

8.3.7. Removal of the Main P.C.B.

(Fig. D8)

(Fig. D10)

26
8.3.8. Removal of the Battery Case 8.3.9. Removal of the Battery Door Unit
and Jack Door

(Fig. D12)
NOTE: (When Installing)
Make sure to confirm the following points when installing.
The Screw is tightened enough.
Installing conditions are fine. (No distortion, no abnormal-
space.)
No dust and/or dirt on Lens surfaces.
LCD image is fine. (No dust and dirt on it, and no gradient
images.)

(Fig. D11)

27
8.4. Lens Disassembly Procedure
Precaution:
1. Do not remove the CCD when disassembling or re-
assembling the lens in order to maintain it clean.
When remove it, refer to item "8.6.".
2. Keep dust or dirt away from the lens.
3. To remove dirt or dust from the lens, blow with dry air.
4. Do not touch the lens surface.
5. Apply grease (RFKZ0472) as shown on "THE APPLICA-
TION OF GREASE METHOD" in the figure.
6. Apply a light coat of grease using an object similar to a
toothpick.
7. The drive frame unit and penetration cam frame should
be replaced as a unit.

8.4.1. Removal of the Zoom Motor and

Lens FPC Unit
1. Remove the 3 tapes.
2. Unscrew the 2 screws (A).
3. Remove the zoom motor to the direction of arrow (1).
4. Unscrew the 1 screw (B).
5. Remove the photo sensor.
6. Remove the 13 solders (A).
7. Remove the 3 solders (B).
8. Remove the 5 locks.

28
 9. Remove the 4 solders (C). 2. Remove the master flange unit.
10. Remove the lens FPC unit to the direction of arrow (3).

8.4.2. Removal of the Master Flange Unit

1. Unscrew the 4 screws (C).

29
8.4.3. Removal of the 1st Lens Frame 8.4.4. Removal of the 2nd Lens Frame
Unit/2nd Lens Frame Unit/Both Unit/Both Sides Cam Frame/2nd
Sides Cam Frame/2nd 3rd Direct 3rd Direct Frame/3rd Lens Frame
Frame/3rd Lens Frame Unit Unit
1. Push the both sides cam frame from the lens front side in 1. Turn the 2nd lens frame unit/both sides cam frame/2nd
the direction of arrow, and then remove the unit of 1st 3rd direct frame/3rd lens frame unit in the direction of the
lens frame unit/2nd lens frame unit/both sides cam frame/ arrow (1) fully, and then remove them in the direction of
2nd 3rd direct frame/3rd lens frame unit from the fixed the arrow (2).
frame unit/drive frame unit/penetration cam frame/1st
direct frame unit.

30
8.4.5. Removal of the 2nd 3rd Direct 8.4.7. Removal of the 2nd Lens Frame
Frame Unit
1. Remove the 2nd 3rd direct frame in the direction of the 1. Turn the 2nd lens frame unit in the direction of the arrow
arrow. (1) fully, and then remove it in the direction of the arrow
(2).

8.4.6. Removal of the 3rd Lens Frame

Unit
1. Remove the 3rd lens frame unit in the direction of the
arrow.

31
8.4.8. Removal of the 1st Direct Frame 8.5. Assembly Procedure for the
Unit Lens
1. Remove the 1st direct frame unit in the direction of the
arrow. 8.5.1. Phase alignment of the Penetration
Cam Frame and Drive Frame Unit

8.4.9. Removal of the Drive/Penetration

Frame Unit
1. Remove the drive/penetration frame unit in the direction
of the arrow.

32
8.5.2. Phase alignment of the Drive/Pene- 8.5.3. Phase alignment of the 2nd Lens
tration Frame Unit and Fixed Frame Frame Unit and Both Sides Cam
Unit Frame

33
8.5.4. Phase alignment of the 3rd Lens 8.5.5. Phase alignment of the 2nd 3rd
Frame Unit and 2nd Lens Frame Direct Frame and 2nd Lens Frame
Unit/Both Sides Cam Frame Unit/Both Sides Cam Frame/3rd
Lens Frame Unit

34
8.5.6. Phase alignment of the 2nd Lens
Frame Unit/Both Sides Cam Frame/
2nd 3rd Direct Frame/3rd Lens
Frame Unit and 1st Lens Frame
Unit

35
8.5.7. Phase alignment of the 1st Lens 8.5.8. Phase alignment of the 1st Direct
Frame Unit/2nd Lens Frame Unit/ Frame Unit/1st Lens Frame Unit/
Both Sides Cam Frame/2nd 3rd 2nd Lens Frame Unit/Both Sides
Direct Frame/3rd Lens Frame Unit Cam Frame/2nd 3rd Direct Frame/
and 1st Direct Frame Unit 3rd Lens Frame Unit and Fixed
Frame Unit/Drive Frame Unit/Pene-
tration Cam Frame

36
8.5.9. Install of the Master Flange Unit 8.5.10. Install of the Lens FPC Unit and
Zoom Motor

37
8.6. Removal of the CCD Unit 8.8. The Application of Grease
To prevent the CCD unit from catching the dust and dirt, do Method
not remove the CCD unit except for replacing.
The grease application parts of lens unit are as follows.
Apply grease additionally in the specified position if necessary.
When the grease is applied, use a toothpick and apply thinly.
Focus motor (lead screw)/Fasten groove of nut/Guide pole
- Grease: RFKZ0472
- Amount of application: 2 - 4 mg
Positioning pole
- Grease: RFKZ0472
- Amount of application: 1 - 2 mg

8.7. Removal of the Focus Motor

38
9 Measurements and Adjustments
9.1. Introduction
When servicing this unit, make sure to perform the adjustments necessary based on the part(s) replaced.
Before disassembling the unit, it is recommended to back up the camera data stored in flash-rom as a data file.
IMPORTANT NOTICE (After replacing the MAIN P.C.B.)
After replacing the MAIN P.C.B., it is necessary to use the DIAS software to allow the release of adjustment flag(s).
The Adjustment software DIAS is available at TSN Website. To download, click on Support Information from NWBG/VDBG-
AVC.
*DIAS (DSC Integrated Assist Software)

9.2. Before Disassembling the unit

9.2.1. Initial Setting Release
The cameras specification are initially set in accordance with model suffix (such as EB, EG, GK, GC, and so on.).
Unless the initial setting is not released, an automatic alignment software in the camera is not able to be executed when the align-
ment is carried out.
Note:
The initial setting should be again done after completing the alignment. Otherwise, the camera may not work properly.
Therefore as a warning, the camera display a warning symbol ! on the LCD monitor every time the camera is turned off.
Refer to the procedure described in 3.4.2 INITIAL SETTINGS for details.

[ How to Release the camera initial setting ]

Preparation:
Attach the Battery or AC Adaptor with a DC coupler to the unit.
(Since this unit has built-in memory, it can be performed without inserting SD memory card.)
1. Turn the Power on.
2. Press the [ MODE ] button, and select the [ NORMAL PICTURE ] mode by Cursor buttons, then press the [ MENU/SET ]
button.
3. Turn the Power off. (If the unit is other than [ NORMAL PICTURE ] mode, it does not display the initial settings menu.)

Step 1. Temporary cancellation of INITIAL SETTINGS:

Set the [ REC ]/[ PLAYBACK ] selector switch to [ REC ] (Camera mark).
While pressing [ UP ] of Cursor button and [ E.ZOOM ] button simultaneously, turn the Power on.
Step 2. Cancellation of INITIAL SETTINGS:
Set the [ REC ]/[ PLAYBACK ] selector switch to [ PLAYBACK ].
Press [ UP ] of Cursor button and [ E.ZOOM ] button simultaneously, then turn the Power off.

The LCD displays the ! mark before the unit powers down.

39
9.2.2. Flash-Rom Data Backup
When trouble occurs, it is recommended to backup the Flash-rom data before disassembling the unit.
There are two kinds of Flash-rom data backup methods:
[ ROM_BACKUP (Method of Non-PC backup) ]
1. Insert the SD-card into the camera.
2. Set the camera to Temporary cancellation of the initial settings.
3. Select the SETUP menu.
From the SETUP menu, select ROM BACKUP.
NOTE:
This item is not listed on the customer's SETUP menu.
4. When this ROM_BACKUP item is selected, the following submenus are displayed.

[ DSC Integrated Assist Software (Method of Using PC) ]

Same as TATSUJIN software for previous models.

9.2.3. Light Box

If using VFK1164TDVLB Light Box, remove the lens connection
ring by loosing three hexagon screws.

40
9.3. Details of Electrical Adjustment
9.3.1. How to execute the Electrical Adjustment
It is not necessary to connect the camera to a PC to perform adjustments.
Flag reset operation and Initial setting operation are required when carrying out the alignment, follow the procedure below.

9.3.1.1. Startup Electrical Adjustment mode

1. Release the initial settings.
2. Insert a recordable SD card.
(Without a SD card, the automatic adjustment can not
executed.)
3. Procedure to set the camera into adjustment mode:
a. Turn the Power on.
b. Press the [ MODE ] button, and select the [ NORMAL
PICTURE ] mode by Cursor buttons, then press the
[ MENU/SET ] button.
c. Turn the Power off.
d. Turn the Power on pressing [ MENU/SET ] and
[ E.ZOOM ] button simultaneously.
LCD monitor displays SERVICE MODE. (Refer to
Fig. 3-1)

9.3.1.2. Status Adjustment Flag Setting

Reset (Not yet adjusted) the status flag condition.
1. After pressing the [ DISP. ] button, the LCD monitor dis-
plays the Flag status screen (Refer to Fig.3-2)
2. Select item by pressing the Cursor buttons. (Gray cursor
is moved accordingly.)
3. Press the [ Delete ] button.
NOTE:
The selected item's flag has been changed from
F (green) to 0 (yellow).
*Flag conditions:
F (green)
means that the alignment has been completed and the
status flag condition is set. In this case, the flag condition
should be reset, if you try to carry out the automatic align-
ment.
0 (yellow)
means that the alignment has been not completed and
the status flag condition is reset. In this case, automatic
alignment is available.

In case of setting the status flag into set condition again without completion of the alignment, the status flag should be SET by
using PC, or UNDO by using ROM BACKUP function.

41
9.3.1.3. Execute Adjustment
(In case of OIS Adjustment)
1. Perform step 9.3.1.1. to 9.3.1.2., to reset the OIS flag
status F (Set) to 0 (Reset)
2. Press [ DISP. ] button after Flag reset.
OIS Adjustment screen is displayed on the LCD panel.
(Refer to Fig.3-3)
3. Press the [ Shutter ] button. The adjustment will start
automatically.

4. When the adjustment is completed successfully, adjust-

ment report menu appears with Green OK on the LCD
monitor. (Refer to Fig.3-4)

9.3.1.4. Attention point during Adjustment

1. Step 9.3.1.3. procedure shows OIS adjustment as an
example. To perform the adjustment, refer to the 9.3.2.
Adjustment Specifications table which shows key point
for each adjustment.
2. Do not move the light box, the camera or the chart while
adjusting. If one of these is moved accidentally, start the
adjustment again.
3. Do not press any buttons/keys until the default menu
(Fig.3-5) is displayed on the LCD monitor. Otherwise,
adjustment data may not be stored properly.
4. If the adjustment is interrupted accidentally, the alignment
data may not be properly saved in the Flash-rom.

9.3.1.5. Finalizing the Adjustment

1. Several adjustment flags can be reset (F into 0) at the same time. In this case, when the adjustment has been completed,
the screen will change showing the adjustment for the next item until all reset items are completed.
Also, when the shutter button is pressed, the screen jump to the next adjustment item.
2. To cancel the adjustment mode while in the process of performing the adjustment, follow this procedures.
(1) Press [ RIGHT ] of cursor button.
NOTE:
If adjustment is cancelled with above procedure, adjustment is not completed. Make sure to adjust it later.
Adjustment software DIAS is able to control the status of the adjustment flags.

42
9.3.2. Adjustment Specifications
The following matrix table shows the relation between the replaced part and the Necessary Adjustment.
When a part is replaced, make sure to perform the necessary adjustment(s) in the order indicated.
The table below shows all the information necessary to perform each adjustment.

43
44
9.4. After Adjustment
9.4.1. Initial Setting
Since the initial setting has been released to execute the built-in adjustment software, it should be set up again before shipping the
camera to the customer.
Refer to the procedure described in 3.4.2. INITIAL SETTINGS for details.

[ IMPORTANT ]
1. The initial setting should be done again after completing the alignment. Otherwise, the camera will not work properly.
Therefore as a warning, the camera display a warning symbol ! on the LCD monitor every time the camera is turned off.
2. Confirm that status of all adjustment flag show F. Even if one of the adjustment flag shows 0, initial setting programmed is
never executed.
3. Adjustment software DIAS is able to control the status of the adjustment flags.
The Adjustment software DIAS is available at TSN Website, therefore, access to TSN Website at Support Information
from NWBG/VDBG-AVC.

45
10 Maintenance
10.1. Cleaning Lens and LCD Panel
Do not touch the surface of lens and LCD Panel with your hand.
When cleaning the lens, use air-Blower to blow off the dust.
When cleaning the LCD Panel, dampen the lens cleaning paper with lens cleaner, and the gently wipe the its surface.
Note:
The Lens Cleaning KIT ; VFK1900BK (Only supplied as 10 set/Box) is available as Service Aid.

46
 DSC1102004CE
S1. About Indication of The Schematic Diagram
Service Manual S1.1. Important Safety Notice

COMPONENTS IDENTIFIED WITH THE MARK HAVE THE SPECIAL CHARACTERISTICS

Diagrams and Replacement

FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.

1.Although reference number of the parts is indicated on the P.C.B. drawing and/or

Parts List schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
Digital Camera 3.The voltage being indicated on the schematic diagram is measured in
Model No. "Standard-Playback" mode when there is no specify mode is mentioned.
DMC-FS35EB DMC-FH25P DMC-FH25GF 4.Although the voltage and waveform available on here is measured with standard frame,
DMC-FS35EE DMC-FH25PC DMC-FH25GH it may be differ from actual measurement due to modification of circuit and so on.
DMC-FS35EF DMC-FH25PR DMC-FH25GK 5.The voltage being indicated here may be include observational-error (deviation) due to
DMC-FS35EG DMC-FH25PU DMC-FH25GN internal-resistance and/or reactance of equipment. Therefore, handle the value
DMC-FS35EP DMC-FH25GA DMC-FH25GT indicated on here as reference.
DMC-FH25GC DMC-FH24P 6.Use the parts number indicated on the Replacement Parts List .

Vol. 1 7.Indication on Schematic diagrams:

Colour Circuit name being connected.
[DMC-FS35] [DMC-FH25]
(S)...........Silver Type (except EF) (S)...........Silver Type (except PC/PR/GT)
(K)...........Black Type (K)...........Black Type This signal is connected
(R)...........Red Type (except EE) (R)...........Red Type (except PR/GT) OFTR FEP
to the FEP schematic diagram.
(A)...........Blue Type (except EF) (A)...........Blue Type (only P/PC/PU/GK/GN)
(V)...........Violet Type (except EE/EF) (V)...........Violet Type (only P/PC/PR/PU/GT)
[DMC-FH24]
Name of Signal
(K)...........Black Type

Table of contents
S1. About Indication of The Schematic Diagram............................. S-1 S6. Replacement Parts List........................................................... S-15
S1.1. Important Safety Notice......................................................... S-1
S7. Exploded View........................................................................ S-20
S2. Voltage Chart............................................................................ S-2 S7.1. Frame and Casing Section.................................................. S-20
S2.1. Flash Top P.C.B...................................................................... S-2 S7.2. Packing Parts and Accessories Section (1)......................... S-21
S7.3. Packing Parts and Accessories Section (2)......................... S-22
S3. Block Diagram........................................................................... S-3
S3.1. Overall Block Diagram........................................................... S-3

S4. Schematic Diagram................................................................... S-4

S4.1. Interconnection Diagram........................................................ S-4
S4.2. Flash Top Schematic Diagram............................................... S-5
S4.3. CCD Flex Schematic Diagram............................................... S-6
S4.4. Lens Flex Schematic Diagram............................................... S-7

S5. Print Circuit Board..................................................................... S-8

S5.1. Flash Top P.C.B...................................................................... S-8
S5.2. CCD Flex P.C.B.................................................................... S-12
S5.3. Lens Flex P.C.B.................................................................... S-13

S-1
S2. Voltage Chart
Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.

S2.1. Flash Top P.C.B.

REF No. PIN No. POWER ON

IC8100 1 0
IC8100 2 0
IC8100 3 0
IC8100 4 0
IC8100 5 3.4
IC8100 6 0
IC8100 7 0
IC8100 8 0
IC8100 9 3.1
IC8100 10 3.9

S-2
S3. Block Diagram
S3.1. Overall Block Diagram

(28mm ~ 224mm)
IC3001
CCD SIGNAL
CCD PROCESSOR X6001
1/2.33" 16 MEGA PIX (24MHz)
CDS, AGC,
A/D, TG,
CCD DRIVER

SD
ZOOM OIS UNIT IRIS SHUTTER FOCUS CARD
IC3003
REGULATOR

MICROPHONE
IC9101
SYSTEM IC IC9101
MOTOR DRIVE, SYSTEM IC SPEAKER
OIS DRIVE& MICROPHONE AMP
PRE PROCESS SPEAKER CONTROL
VIDEO OUT

IC7101
GYRO AV OUT / DIGITAL
TERMINAL
SENSOR & AMP

IC8100 IC6001
FLASH VENUS6
IGBT DRIVER
CAMERA PROCESS
J-PEG COMP/EX PANDS
MEDIA I/F
USB I/F
MAIN MICROPROCESSOR
OIS CONTROL
LENS DRIVE
REAR OPERATION UNIT LCD DRIVE

COLOR LCD
PANEL
2.7" PANEL
230k dots
IC9101
SYSTEM IC

X9101 IC1110,1210,1220
(32.768kHz)
REGULATOR
IC6002
SDRAM/512Mbit
NAND FLASH ROM/1Gbit

IC1001
POWER BATTERY
(POWER SUPPLY)
TOP OPERATION UNIT

DMC-FS35/FH25/FH24 OVERALL BLOCK DIAGRAM

S-3
S4. Schematic Diagram
S4.1. Interconnection Diagram

STB CHG DET

UNREG GND
UNREG GND
UNREG GND
UNREG GND
UNREG GND
FLASH TRG

ID BUT DQ
CATHODE
IGBT VCC

SP NEG
SP POS

IA SW
WIDE
NC
FLASH TOP P.C.B. M8001

(COMPONENT SIDE) MICROPHONE

15
14
13
12
11
10
PS8001

9
8
7
6
5
4
3
2
1
: (FOIL SIDE)

16 STB CHG OUT

24 BAT THERMO
25 POWER ON L
26 FRAME GND
SHUTTER 0
SHUTTER 1
MIC GND

UNREG+
UNREG+
UNREG+
UNREG+
A GND
MIC IN

TELE
NC

2 BAT THERMO

4 UNREG GND
ID BAT DQ
UNREG+
P8002

17
18
19
20
21
22
23

27
28
29
30
RL8001 RL8002

3
SPEAKER

BATTERY

16 STB CHG OUT

24 BAT THERMO
25 POWER ON L
26 FRAME GND
SHUTTER 0
SHUTTER 1
FP9001

MIC GND

UNREG+
UNREG+
UNREG+
UNREG+
A GND
MIC IN

TELE
1 CON CHK

NC
SUBSW2 2 CCD THERMO
3
4 SUBSW1
5 SUB
6 MSUBSW
7 MSUB
8 V16
9 V15D
10 V15

17
18
19
20
21
22
23

27
28
29
30
11 V14
12 V13Z
13 V13Y

STB CHG DET

14 V13X

UNREG GND
UNREG GND
UNREG GND
UNREG GND
UNREG GND
FLASH TRG
15 V12Z

ID BAT DQ
CATHODE
IGBT VCC
16 V12Y

SP NEG
SP POS
17 V12X

IA SW
WIDE
18 V12

NC
19 V11
20 V10
21 V9
22 V8
23 V7
24 V6
25 V5
26 V4

15
14
13
12
11
10
27 V3

9
8
7
6
5
4
3
2
1
28 V2A
29 V2B PP9001
30 V1A
31 V1B
33 VH
32 VL FP9003 LCD UNIT
34 CCD GND
35 CCD GND 1 GREST
36 CCD GND 2 SDA/SCEN
37 CCD OUT 3 SCL
38 CCD GND 4 SCEN/SDA
39 CCD GND 5 VSYNC/NA
40 RG 6 HSYNC/NA
41 HL 7 DCLK/NA
42 H3 8 DIN7
43 H1 9 DIN6
44 H2 10 DIN5
45 H4 11 DIN4
46 CCD GND 12 DIN3
47 CON CHK 13 DIN2
14 DIN1
15 DIN0
16 NA/DCLK
17 NA/HSYNC
18 VDD 1.8/VSYNC
19 NA/VCC
20 VDD/VCC
21 VSSA/GND
22 VSS/GND
23 CP1/GND
24 CN1/GND
25 CP2 26 CN2/CP1
27 VDD2/AVDD
28 CP3/AGND
29 CN3/AGND
30 VCL/VCOMH
31 CP4/VCOML
32 CN4/PCD
33 CP5/VCC 1.8
34 CN5/CP8
35 VGH/CP7 36 VGL/CP6

MAIN P.C.B.
37 VCS/CP5
39 VCOM/CP3
38 VCOMH/CP4
40 LED+
SUB P.C.B.
41
(FOIL SIDE)
LED-
(FOIL SIDE)

CCD FP9002
UNIT 1 FZHP LED
2 FZHP ABS
3 FZHP VCC
4 NC
5 YHO+
6 YV+
7 YHO-
8 IRIS-
9 IRIS-
LENS 11 IRIS+
10 IRIS+
UNIT 12 SH+
13 SH+
14 SH-
15 SH-
16 XDR-
17 XDR+
18 XV-
19 XHO+
20 XV+
21 XHO-
22 YDR-
23 YDR+ PS9001 PP9501
24 YV-
25 GND 26 ZM- 16 A3R1V 1 AGND 1 AGND 16 A3R1V
27 ZM- 28 ZM+ 15 UP/DOWN/LEFT/RIGHT 2 OIS GY DO 2 OIS GY DO 15 UP/DOWN/LEFT/RIGHT
29 ZM+ 30 GND 14 XP 3 OIS GY DI 3 OIS GY DI 14 -
31 ZENC2 LED 32 ZENC2 ABS 13 MENU 4 OIS GY SCK 4 OIS GY SCK 13 MENU
33 ZENC VCC 34 ZENC1 LED 12 XN 5 YP 5 - 12 -
35 ZENC1 ABS 36 FMBN 11 MODE 6 OIS GY CS 6 OIS GY CS 11 MODE
37 FMBN 38 FMAP 10 DISPLAY 7 DELETE 7 DELETE 10 DISPLAY
39 FMAP 40 FMBP 9 D GND 8 YN 8 - 9 D GND
41 FMAN

DMC-FS35/FH25/FH24 INTERCONNECTION DIAGRAM

S-4
S4.2. Flash Top Schematic Diagram

T/W_SW i.A.
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,
REPLACE ONLY WITH THE SAME TYPE 2.0A 32V FUSE.
S8004 ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES
2.0A 32V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MME TYPE 2.0A 32V.
F 1 4
K0F111A00541

K0L1CB000003
3 1

S8003
SHUTTER_SW
4 2 2.0A 32V
CL8026
2 3 C8018 F8021
F1G0J1050007 P8002
S8001
6.3V ERBSE2R00U K4ZZ04000057
K0F212A00003 1 UNREG+
5
2 BAT_THERMO
3 ID_BAT_DQ
1 2
4 UNREG_GND

3 4
E 6

C8017
$

CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD, 1 WIDE UNREG+ 30

REPLACE ONLY WITH THE SAME TYPE 1.25A 32V FUSE. C8019 2 IA_SW UNREG+ 29
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES R8037 R8038 $ 3 ID_BUT_DQ UNREG+ 28
1.25A 32V D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MME TYPE 1.25A 32V. (3.4V) 22[18] 22[18] C8014
TL8002 TL8003 4 CATHODE UNREG+ 27 F1G1A1040006
5 NC FRAME_GND 26
LAMP[-] LAMP[+] 10V
D8001 6 UNREG_GND POWER_ON_L 25
B3ADA0000230 OFF
1.25A 32V 7 UNREG_GND BAT_THERMO 24 ON
(HFO803165CP(D6)-S2)
CL8001 8 UNREG_GND TELE 23 6 3 2 1 4
TL8001
D
F8001 9 UNREG_GND NC 22
ERBSE1R25U $[D4ED18R00008]
10 UNREG_GND SHUTTER_1 21
C8015 7 5
"K" RL8001 11 SP_NEG SHUTTER_0 20 M8001 K0D112B00145
L8001 D8002 T8001 To SPK LB8001 L0CBAY000093
TRG SECOND R8005 "R" RL8002 12 SP_POS A_GND 19 J0JCC0000415 S8002
G5F1A0000026 B0ECFR000003 G5D1A0000080 $[D4ED18R00008]
3 510K[22] 13 IGBT_VCC MIC_IN 18
F C8016

2
#S R8006 S

C8022
14 STROBE_TRG MIC_GND 17

$
TRG_G TRG FIRST 510K[22] STB_CHG_DET STB_CHG_OUT
15 16
2 1 ET8004
#S
R8032 C8009 N9ZZ00000333 K1KB30AA0123
D1BD4703A119 [F][22] PS8001
4

1
S F F1J1A106A043

10V
C8003
CL8032 CL8031
F2A2F8800003 CL8004
300V88uF IC8100 CL8006
315V

C0ZBZ0001817

8 7 6 5
9 10
1

C C8006 PGND SW
2

C F1K2E4730005 IGBT_OUT FULL

250V

G [36] GND RADJ

E
4

VC IGBT_IN SAFETY_GND
F1G1H150A557

SLEEVE_GND
15p

6.3V VCC START

1 2 3 4 R8013 TL8007
CL8005 R8003
C8001

$[D4ED18R00008]
ET8003 ERJ2RHD1621X
F1G0J1050007

B1JBLP000030 120[18]
50V
C8007

VMB4278 1620[D]

VA8001
Q8001 R8021
CL8011
47K
R8002 TL8004
100K[18] TOP PLATE

CL8008
VMP9873
ET8005

CL8010

A
Confidential
Until DMC-FS35/FH25/FH24
Flash Top
Schematic Diagram

1 2 3 4 5 6 7 8 9 10

S-5
S4.3. CCD Flex Schematic Diagram

FT3101
F 47 CON_CHK
46 CCD_GND

V12Z

V13X
V13Y
V13Z

V15D

MSUB
V14
V15

V16
H4
45 H4
H2
44 H2
H1
43 H1
H3
42 H3
HL
41 HL
42 41 40 39 38 37 36 35 34 33 RG
40 RG
V12Y

NC
V14
V15
MSUBSW

V13X

V13Y
V13Z

V15D
V16
1 32 39 CCD_GND
V12X
2 V12X NC 31 38 CCD_GND
V12 [42]V12Z [33]MSUB H4
3 V12 [32]MSUBSW H4 30 37 CCD_OUT
V11 [1]V12Y H2
4 V11 H2 29 36 CCD_GND
E

4
V10 SUB

DMS935E10R
5 V10 SUB 28 35 CCD_GND
IC3101 R3107

Q3101
V9 H1

S
6 V9 H1 27 34 CCD_GND
MN34590PLHAV H3 1300
7 PT H3 26 33 VH

G
V8 HL
8 V8 VL

3
HL 25 32
V7 SUBSW1 V1B
9 V7 SUBSW1 24 31 V1B
V6 [12]V4 [22]RG SUBSW2 V1A
10 V6 SUBSW2 23 30 V1A
V5 RG V2B
V2A
V2B
V1A
V1B

GND1
GND2
11 V5
V3

22 29 V2B

VDD
R3101

VO
V2A
47 28 V2A
12 13 14 15 16 17 18 19 20 21 V3
27 V3
V4
26 V4
R3108 V5
25 V5
V6
24 V6
D R3102
22 V7
23 V7
V8
V2A
V2B
V1A
V1B

2200 22 V8
V4
V3

V9
C3101 21 V9
V10
F1H1C105A097 20 V10
V11

16V
19 V11
V12
18 V12
V12X
17 V12X
V12Y
16 V12Y
V12Z
15 V12Z
V13X
14 V13X
V13Y
13 V13Y
V13Z
12 V13Z
C V14
11 V14
V15
10 V15
V15D
9 V15D
V16
8 V16
MSUB
7 MSUB
MSUBSW
6 MSUBSW
SUB
5 SUB
SUBSW1
4 SUBSW1
SUBSW2
3 SUBSW2
TH3101
2 CCD_THERMO
D4CC11030026 1 CON_CHK

B or

Confidential
Until

A
DMC-FS35/FH25/FH24
CCD Flex
Schematic Diagram

1 2 3 4 5 6 7 8 9 10

S-6
S4.4. Lens Flex Schematic Diagram

POSITIVE VOLTAGE LINE

A1
FZHP LED 1
PHOTO
A2 A CO. BARREL ENCODER
FZHP ABS 2 SENSOR
A3
(FULL RETRACT)
FZHP VCC 3

NC 4
B1
YHO+ 5
B2
YV+ 6
F B3
YHO- 7 HALL SENSOR (Y) B OIS UNIT
C1
IRIS- 8

IRIS- 9
DC SOLENOID
IRIS+ 10 (IRIS)
C2
IRIS+ 11
C3 C SHUTTER UNIT
SH+ 12

SH+ 13 DC SOLENOID
(SHUTTER)
E SH- 14
C4
SH- 15
B4
XDR- 16
B5
XDR+ 17 DRIVE COIL (X)
B6
XV- 18
B7
HALL SENSOR (X)
TO MAIN XHO+ 19
(MAIN CN) CIRCUIT B8
20 B OIS UNIT
(FP9002) XV+
B9
XHO- 21
D B10
YDR- 22

YDR+ 23
B11 DRIVE COIL (Y)
B12
YV- 24

GND 25
D1
ZM- 26

ZM- 27 DC MOTOR D ZOOM MOTOR UNIT

ZM+ 28
D2
C ZM+ 29

GND 30
E1
ZENC2 LED 31 PHOTO
E ZOOM ENCODER 2
ZENC2 ABS 32
E2 SENSOR
E3/F1
ZENC VCC 33
F2
ZENC1 LED 34 PHOTO
F ZOOM ENCODER 1
35
F3 SENSOR
ZENC1 ABS
G1
FMBN 36
B
FMBN 37
G2
FMAP 38
COIL STEPPING
FMAP 39
G FOCUS MOTOR UNIT
G3 MOTOR
FMBP 40
G4 COIL
FMAN 41

DMC-FS35/FH25/FH24 LENS FLEX SCHEMATIC DIAGRAM

1 2 3 4 5 6

S-7
S5. Print Circuit Board
S5.1. Flash Top P.C.B.

1/4 DMC-FS35/FH25/FH24
Flash Top P.C.B.
(Component Side)
N

L
CL800

ET8003

10
1
R8003

IC8100
TL8004

R8002
1234

C8007

R8013

VA8001
C8003 F8001 C8001 R8021
CL8005 Q8001 CL8008
K CL8010

R8032
D8002
CL8011
2
8765 CL8032
D8001

C8006
CL8031
1

R8005

R8006
J

(Component Side)
I

S-8
G
 2/4 DMC-FS35/FH25/FH24
Flash Top P.C.B.
(Component Side)

15 10 5 1
CL8006
CL8004

PS8001
ET8005

16 20 25 30

F8021

2 1 2 3 4
L8001
3 TL8001
1 TL8007

P8002

TL8002

S-9
H

F C8022

C8014
LB8001
7 5

C8019

C8018
S8002

4
6 4
S8001

2
3 2 1

1
2
4
00

6
S8
E

S800
4

3
CL8026

4
3
C8017

(Foil Side)

A
DMC-FS35/FH25/FH24
Flash Top P.C.B.
3/4 (Foil Side)

1 2 3 4 5 6 7 8 9 10 11

S-10
 5 M8001
S8002 2 1

4 TL8003
2 1
1 CL8001 4 3
ET8004
T8001
1

C8009
C8016

C8015

1 2
RL8002 RL8001 R8038 R8037

DMC-FS35/FH25/FH24
Flash Top P.C.B.
4/4 (Foil Side)

11 12 13 14 15 16 17 18 19 20 21

S-11
S5.2. CCD Flex P.C.B.

FT3101
(Component Side)
C3101

R3102
R3108 TH3101

Q3101
1 2 3 10 11 5 1

C 12 42

R3107
6 5 4
40
15
IC3101

35
20

R3101
21 33
22 25 32 30

(Foil Side)

DMC-FS35/FH25/FH24
CCD Flex P.C.B.

1 2 3 4 5 6 7 8 9 10

S-12
S5.3. Lens Flex P.C.B.

D ZOOM MOTOR UNIT B OIS UNIT A1 A2 A CO. BARREL ENCODER

(FULL RETRACT)
C4
C3
B9
B8
B7
B6
B5
B4

D2 A3
D1

D
C1
C2
B1
B2
B3

C SHUTTER
UNIT

B10
B11
B12
Pin 1
C E1 F3
E3 F1
F ZOOM
E2 F2 ENCODER 1
E ZOOM
ENCODER 2

Pin 41
B

G2 G4

G1 G3
A
G FOCUS MOTOR
UNIT

DMC-FS35/FH25/FH24 LENS FLEX P.C.B.

1 2 3 4 5 6

S-13
S-14
S6. Replacement Parts List

Note: 1. * Be sure to make your orders of replacement parts according to this list.
2. IMPORTANT SAFETY NOTICE
Components identified with the mark have the special characteristics for safety.
When replacing any of these components, use only the same type.
3. Unless otherwise specified,
All resistors are in OHMS, K=1,000 OHMS. All capacitors are in MICRO-FARADS (uf), P=uuF.
4. The marking (RTL) indicates the retention time is limited for this item. After the discontinuation
of this assembly in production, it will no longer be available.
5. Supply of CD-ROM, in accordance with license protection, is allowable as replacement parts
only for customers who accidentally damaged or lost their own.

E.S.D. standards for Electrostatically Sensitive Devices, refer to PREVENTION OF

ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES
section.
Definition of Parts supplier:
1. Parts marked with [ENERGY] in the remarks column are supplied from Panasonic
Corporation Energy Company.
2. Parts marked with [SPC] in the remarks column are supplied from AVC-CSC-SPC.
Others are supplied from PAVCSG.

S-15
 DMC-FS35EG-S

Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks

## VEP56126C MAIN P.C.B. 1 (RTL) E.S.D.

## VEP59094A SUB P.C.B. 1 (RTL) E.S.D.
## VEP58149A FLASH TOP P.C.B. 1 (RTL) E.S.D.
## VEK0R36 CCD UNIT 1 [SPC] E.S.D.

## VEP58149A FLASH TOP P.C.B. (RTL) E.S.D.

C8001 F1G0J1050007 C.CAPACITOR CH 6.3V 1U 1

C8006 F1K2E4730005 C.CAPACITOR 250V 0.047U 1
C8007 F1G1H150A557 C.CAPACITOR CH 50V 15P 1
C8009 F1J1A106A043 C.CAPACITOR CH 10V 10U 1
C8014 F1G1A1040006 C.CAPACITOR CH 10V 0.1U 1
C8018 F1G0J1050007 C.CAPACITOR CH 6.3V 1U 1

D8002 B0ECFR000003 DIODE 1 E.S.D.

ET8004 N9ZZ00000333 EARTH SPRING 1

 F8001 ERBSE1R25U FUSE 32V 1.25A 1

 F8021 ERBSE2R00U FUSE 32V 2.0A 1

IC8100 C0ZBZ0001817 IC 1 E.S.D.

L8001 G5F1A0000026 CHIP INDUCTOR 1

LB8001 J0JCC0000415 FILTER 1

P8002 K4ZZ04000057 CONNECTOR 4P 1

PS8001 K1KB30AA0123 CONNECTOR 30P 1

Q8001 B1JBLP000030 TRANSISTOR 1 E.S.D.

R8002 ERJ3GEYJ104V M.RESISTOR CH 1/10W 100K 1

R8003 ERJ3GEYJ121V M.RESISTOR CH 1/10W 120 1
R8005 ERJ6GEYJ514V M.RESISTOR CH 1/8W 510K 1
R8006 ERJ6GEYJ514V M.RESISTOR CH 1/8W 510K 1
R8013 ERJ2RHD1621X M.RESISTOR CH 1/16W 1620 1
R8021 ERJ2GEJ473X M.RESISTOR CH 1/16W 47K 1
R8032 D1BD4703A119 RESISTOR 1
R8037 ERJ3GEYJ220V M.RESISTOR CH 1/10W 22 1
R8038 ERJ3GEYJ220V M.RESISTOR CH 1/10W 22 1

S8001 K0F212A00003 SWITCH 1

S8002 K0D112B00145 SWITCH 1
S8003 K0L1CB000003 SWITCH 1
S8004 K0F111A00541 SWITCH 1

T8001 G5D1A0000080 TRANSFORMER 1

## VEK0R36 CCD UNIT [SPC] E.S.D.

C3101 F1H1C105A097 C.CAPACITOR CH 16V 1U 1 [SPC]

Q3101 DMS935E10R SILICON TRANSISTORS 1 [SPC]

R3101 ERJ2GEJ470 M.RESISTOR CH 1/16W 47 1 [SPC]

R3102 ERJ2GEJ222 M.RESISTOR CH 1/10W 2.2K 1 [SPC]
R3107 ERJ2GEJ132 M.RESISTOR CH 1/10W 1.3K 1 [SPC]
R3108 ERJ2GEJ220 M.RESISTOR CH 1/16W 22 1 [SPC]

TH3101 D4CC11030026 NTC THERMISTORS 1 [SPC]

S-16
 DMC-FS35EG-S

Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks

1 VEP56126C MAIN P.C.B. 1 (RTL) E.S.D. 100 VXW1229 LENS UNIT (W/O CCD) 1 [SPC]
2 VEP58149A FLASH TOP P.C.B. 1 (RTL) E.S.D. 102 VEK0R36 CCD UNIT 1 [SPC] E.S.D.
3 VEP59094A SUB P.C.B. 1 (RTL) E.S.D. 103 L6DA8DFC0002 ZOOM MOTOR 1 [SPC]
4 ML-421S/DN BATTERY 1 (B9101) [ENERGY] 104 VEK0P74 LENS FPC UNIT 1 [SPC]
5 VGQ0S76 DPR SHEET 1 104-1 B3NBA0000011 PHOTO SENSOR 1 [SPC]
6 VGQ0V76 DPR SHEET 1 104-2 B3NBA0000011 PHOTO SENSOR 1 [SPC]
7 VMP9869 FRAME PLATE 1 104-3 B3NBA0000011 PHOTO SENSOR 1 [SPC]
8 VYK4N13 FRONT CASE UNIT 1 35EG-S,EP-S,EB-S,EE-S, 105 VDW1958 BOTH SIDES CAM FRAME 1 [SPC]
25PU-S,GC-S,GH-S,GF-S, 106 VDW1962 2ND 3RD DIRECT FRAME 1 [SPC]
GA-S,GK-S,GN-S 107 VXP3556 1ST LENS FRAME UNIT 1 [SPC]
8 VYK4N31 FRONT CASE UNIT 1 35EG-K,EP-K,EF-K,EB-K, 108 VXP3579 1ST DIRECT FRAME UNIT 1 [SPC]
EE-K, 25PC-K,PU-K,PR-K, 109 VXP3349 2ND LENS FRAME UNIT 1 [SPC]
GC-K,GH-K,GF-K,GA-K, 110 VXP3350 3RD LENS FRAME UNIT 1 [SPC]
GT-K,GK-K,GN-K 111 VXQ2071 FIX FRAME UNIT 1 [SPC]
8 VYK4N32 FRONT CASE UNIT 1 35EG-R,EP-R,EF-R,EB-R, 112 VXQ2072 MASTER FLANGE UNIT 1 [SPC]
25PC-R,PU-R,GC-R,GH-R, 112-1 L6HA64NC0020 FOCUS MOTOR UNIT 1 [SPC]
GF-R,GA-R,GK-R,GN-R 112-2 VMB4333 FOCUS SPRING 1 [SPC]
8 VYK4N33 FRONT CASE UNIT 1 35EG-A,EP-A,EB-A,EE-A, 112-3 VXP3358 4TH LENS FRAME UNIT 1 [SPC]
PC-A,PU-A,GK-A,GN-A 113 VXP3560 DRIVE/PENETRAION FRAME UNIT 1 [SPC]
8 VYK4N34 FRONT CASE UNIT 1 35EG-V,EP-V,EB-V, 25PC-V, 114 VZT0938 TAPE A 1 [SPC]
PU-V,PR-V,GT-V 115 VZT0938 TAPE A 1 [SPC]
8 VYK4N50 FRONT CASE UNIT 1 25P-S 116 VZT0939 TAPE B 1 [SPC]
8 VYK4N51 FRONT CASE UNIT 1 25P-K, 24P-K
8 VYK4N52 FRONT CASE UNIT 1 25P-R B1 VHD2081 SCREW 1 (-S)
8 VYK4N53 FRONT CASE UNIT 1 25P-A B1 VHD2082 SCREW 1 (-K/R/A/V)
8 VYK4N54 FRONT CASE UNIT 1 25P-V B2 VHD2081 SCREW 1 (-S)
8-1 VGK3718 LENS RING 1 B2 VHD2082 SCREW 1 (-K/R/A/V)
9 VYK4N35 REAR CASE UNIT 1 (-S) B3 VHD2081 SCREW 1 (-S)
9 VYK4N36 REAR CASE UNIT 1 (-K) B3 VHD2082 SCREW 1 (-K/R/A/V)
9 VYK4N37 REAR CASE UNIT 1 (-R) B4 VHD2194 SCREW 1 (-S)
9 VYK4N38 REAR CASE UNIT 1 (-A) B4 VHD2195 SCREW 1 (-K/R/A/V)
9 VYK4N39 REAR CASE UNIT 1 (-V) B5 VHD2194 SCREW 1 (-S)
9-1 VGU0H57 CURSOR BUTTON 1 B5 VHD2195 SCREW 1 (-K/R/A/V)
9-2 VGU0H58 SET BUTTON 1 B6 VHD2194 SCREW 1 (-S)
10 VYK4N40 BATTERY DOOR UNIT 1 (-S) B6 VHD2195 SCREW 1 (-K/R/A/V)
10 VYK4N41 BATTERY DOOR UNIT 1 (-K) B7 VHD2194 SCREW 1 (-S)
10 VYK4N42 BATTERY DOOR UNIT 1 (-R) B7 VHD2195 SCREW 1 (-K/R/A/V)
10 VYK4N43 BATTERY DOOR UNIT 1 (-A) B8 VHD2194 SCREW 1 (-S)
10 VYK4N44 BATTERY DOOR UNIT 1 (-V) B8 VHD2195 SCREW 1 (-K/R/A/V)
11 B3ADA0000230 AF LED 1 (D8001) E.S.D. B9 VHD2194 SCREW 1 (-S)
 12 F2A2F8800003 E.CAPACITOR 1 (C8003) B9 VHD2195 SCREW 1 (-K/R/A/V)
13 L0AA01A00098 SPEAKER 1 B10 VHD2210 SCREW 1
14 L0CBAY000093 MICROPHONE UNIT 1 (M8001) B11 VHD1909 SCREW 1
15 VEK0R28 FLASH UNIT 1 B12 VHD1909 SCREW 1
16 VGL1290 AF PANEL LIGHT 1 B13 VHD1909 SCREW 1
17 VMB4278 C-EARTH SPRING 1 (ET8003) B14 VHD1998 SCREW 1
18 VMP9873 TOP PLATE 1 (ET8005) B15 VHD1998 SCREW 1
19 VMT2136 MIC DUMPER 1 B16 VHD2004 SCREW 1
20 VMT2137 IRIS DUMPER 1 B17 XQN16+BJ7FN SCREW 1
21 VYK4P46 TOP CASE UNIT 1 35EG,EP,EF,EB,EE B18 XQN16+BJ7FN SCREW 1
21 VYK4P45 TOP CASE UNIT 1 25P,PC,PU,PR,GC,GH,GF, B19 XQN16+BJ7FN SCREW 1
GA,GT,GK,GN B101 VHD1871 SCREW 1 [SPC]
21 VYK5A18 TOP CASE UNIT 1 24P B102 VHD1871 SCREW 1 [SPC]
21-1 VGQ0J75 POWER KNOB BASE 1 B103 VHD2011 SCREW 1 [SPC]
21-2 VGU0H46 POWER KNOB 1 B104 VHD2296 SCREW 1 [SPC]
21-3 VGU0H66 EZ BUTTON 1 B105 VHD2296 SCREW 1 [SPC]
22 VGQ0M78 BATTERY LOCK KNOB 1 B106 VHD2296 SCREW 1 [SPC]
23 VKF4789 JACK DOOR 1 (-S) B107 VHD2296 SCREW 1 [SPC]
23 VKF4836 JACK DOOR 1 (-K) B108 VHD2296 SCREW 1 [SPC]
23 VKF4837 JACK DOOR 1 (-R) B109 VHD2296 SCREW 1 [SPC]
23 VKF4838 JACK DOOR 1 (-A) B110 VHD2296 SCREW 1 [SPC]
23 VKF4839 JACK DOOR 1 (-V) B111 VHD2296 SCREW 1 [SPC]
24 VMB4152 BATTERY LOCK SPRING 1
25 VMB4337 BATTERY OUT SPRING 1
26 VMP9240 TRIPOD 1
27 VMP9868 FRAME 1
28 VMP9872 BATTERY CASE 1
29 VMS7863 BATTERY DOOR SHAFT 1
30 VMS7863 JACK DOOR SHAFT 1
31 VYK5C83 LCD UNIT 1
31-1 VYP9322 LCD PANEL UNIT 1
32 VGQ0R77 PCB SPACER 1
33 VGU0F46 MODE KNOB 1

S-17
 DMC-FS35EG-S

Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks

200 VPF1372-A CAMERA BAG 1 P,PC,PU

 201 DE-A91BA/SX BATTERY CHARGER 1 P,PC,PU
 202 ----- BATTERY 1 P,PC,PU
204 K1HY08YY0019 USB CABLE W/PLUG 1 25P,PC,PU
205 K1HY08YY0020 AV CABLE W/PLUG 1 25P,PC,PU
206 VFC4297-B HAND STRAP 1 P,PC,PU
208 VPF1378 BAG, POLYETHYLENE 1 P,PC,PU
 211 VFF0726-S CD-ROM 1 25P,PC,PU, 24P
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes"
212 VQC8055 O/I SOFTWARE 1 25P,PC, 24P
(ENGLISH/CANADIAN FRENCH)
212 VQC8056 O/I SOFTWARE 1 25PU
(SPANISH/PORTUGUESE)
 213 VQT3D29 BASIC O/I 1 25P, 24P
(ENGLISH/SPANISH)
 213 VQT3D30 BASIC O/I 1 25PC
(ENGLISH/CANADIAN FRENCH)
 213 VQT3D31 BASIC O/I 1 25PU
(SPANISH/PORTUGUESE)
214 VPK4672 PACKING CASE 1 25P-S
214 VPK4677 PACKING CASE 1 25P-K
214 VPK4682 PACKING CASE 1 25P-R
214 VPK4687 PACKING CASE 1 25P-A
214 VPK4692 PACKING CASE 1 25P-V
214 VPK4673 PACKING CASE 1 25PU-S
214 VPK4678 PACKING CASE 1 25PU-K
214 VPK4683 PACKING CASE 1 25PU-R
214 VPK4688 PACKING CASE 1 25PU-A
214 VPK4693 PACKING CASE 1 25PU-V
214 VPK4988 PACKING CASE 1 24P-K
214 VPK4677 PACKING CASE 1 PC-K
Please use the attached
Ref No.221 (UPC LABEL)
214 VPK4682 PACKING CASE 1 PC-R
Please use the attached
Ref No.221 (UPC LABEL)
214 VPK4687 PACKING CASE 1 PC-A
Please use the attached
Ref No.221 (UPC LABEL)
214 VPK4692 PACKING CASE 1 PC-V
Please use the attached
Ref No.221 (UPC LABEL)
215 VPN7163 CUSHION 1 25P,PC,PU, 24P
220 VQL2C67-A OPERATING LABEL 1 25PC
221 VQL2J25 UPC LABEL 1 25PC-K
221 VQL2J27 UPC LABEL 1 25PC-R
221 VQL2J29 UPC LABEL 1 25PC-A
221 VQL2J31 UPC LABEL 1 25PC-V

S-18
 DMC-FS35EG-S

Ref.No. Part No. Part Name & Description Pcs Remarks Ref.No. Part No. Part Name & Description Pcs Remarks
 313 VQT3D45 BASIC O/I 1 25GT
300 VPF1372-A CAMERA BAG 1 EXCEPT P,PC,PU (CHINESE(TRADITIONAL))
 301 DE-A92AA/SX BATTERY CHARGER 1 35EG,EP,EF,EB,EE, 25GN  313 VQT3D46 BASIC O/I 1 25GK
 301 DE-A92DA/SX BATTERY CHARGER 1 25PR (CHINESE(SIMPLIFIED))
 301 DE-A92BA/SX BATTERY CHARGER 1 25GH,GF,GA,GK  313 VQT3D47 BASIC O/I 1 25GN
 301 DE-A92CA/SX BATTERY CHARGER 1 25GT (ENGLISH)
 301 DE-A92BA BATTERY CHARGER 1 25GC [SPC] 314 VPK4674 PACKING CASE 1 35EG-S,EP-S,EB-S,EE-S
 302 ----- BATTERY 1 EXCEPT P,PC,PU 314 VPK4679 PACKING CASE 1 35EG-K,EP-K,EF-K,EB-K,
304 K1HY08YY0019 USB CABLE W/PLUG 1 EXCEPT P,PC,PU EE-K
305 K1HY08YY0020 AV CABLE W/PLUG 1 EXCEPT P,PC,PU 314 VPK4684 PACKING CASE 1 35EG-R,EP-R,EF-R,EB-R
306 VFC4297-B HAND STRAP 1 EXCEPT P,PC,PU 314 VPK4689 PACKING CASE 1 35EG-A,EP-A,EB-A,EE-A
308 VPF1378 BAG, POLYETHYLENE 1 EXCEPT P,PC,PU 314 VPK4694 PACKING CASE 1 35EG-V,EP-V,EB-V
 311 VFF0727-S CD-ROM 1 35EG,EP,EF,EB 314 VPK4680 PACKING CASE 1 25PR-K,GH-K,GA-K,GT-K,
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes" GN-K
 311 VFF0728-S CD-ROM 1 35EE 314 VPK4695 PACKING CASE 1 25PR-V,GT-V
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes" 314 VPK4675 PACKING CASE 1 25GH-S,GA-S,GN-S
 311 VFF0729-S CD-ROM 1 25GH,GF,GA,GT,GN 314 VPK4685 PACKING CASE 1 25GH-R,GA-R,GN-R
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes" 314 VPK4676 PACKING CASE 1 25GF-S
 311 VFF0730-S CD-ROM 1 25GK 314 VPK4681 PACKING CASE 1 25GF-K
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes" 314 VPK4686 PACKING CASE 1 25GF-R
 311 VFF0726-S CD-ROM 1 25PR 314 VPK4697 PACKING CASE 1 25GK-S
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes" 314 VPK4698 PACKING CASE 1 25GK-K
 311 VFF0794-S CD-ROM 1 25GC 314 VPK4699 PACKING CASE 1 25GK-R
(SOFT/INSTRUCTION BOOK) [SPC] See "Notes" 314 VPK4700 PACKING CASE 1 25GK-A
312 VQC8057 O/I SOFTWARE 1 35EG 314 VPK4690 PACKING CASE 1 25GN-A
(GERMAN/FRENCH/ITALIAN/ 314 VPK4918 PACKING CASE 1 25GC-K [SPC]
DUTCH/SPANISH/ 314 VPK4917 PACKING CASE 1 25GC-S [SPC]
PORTUGUESE/TURKISH) 314 VPK4919 PACKING CASE 1 25GC-R [SPC]
312 VQC8058 O/I SOFTWARE 1 35EP 315 VPN7164 CUSHION 1 35EG,EP,EF,EB,EE, 25PR,
(FINNISH/SWEDISH/DANISH/ GC,GH,GF,GA,GT,GK,GN
POLISH/CZECH/HUNGARIAN)  319 K2CT3YY00034 AC CORD W/PLUG 1 35EB, 25GH
312 VQC8059 O/I SOFTWARE 1 35EF  319 K2CT39A00002 AC CORD W/PLUG 1 25GC [SPC]
(FRENCH)  320 K2CQ2YY00082 AC CORD W/PLUG 1 35EG,EP,EF,EE, 25GF,GA
312 VQC8060 O/I SOFTWARE 1 35EB, 25GN  321 K2CJ2YY00052 AC CORD W/PLUG 1 25GN
(ENGLISH)  322 K2CA2YY00129 AC CORD W/PLUG 1 25GT
312 VQC8061 O/I SOFTWARE 1 35EE  322 K2CA2YY00130 AC CORD W/PLUG 1 25GK
(RUSSIAN/UKRAINIAN)  323 K2CJ2YY00053 AC CORD W/PLUG 1 25PR
312 VQC8062 O/I SOFTWARE 1 25GC,GH,GF,GA 325 VQL2C68-1A TAIWAN OPE LABEL 1 25GT
(ENGLISH/
CHINESE(TRADITIONAL)/
ARABIC/PERSIAN)
312 VQC8063 O/I SOFTWARE 1 25GT
(CHINESE(TRADITIONAL))
312 VQC8064 O/I SOFTWARE 1 25GK
(CHINESE(SIMPLIFIED))
312 VQC8056 O/I SOFTWARE 1 25PR
(SPANISH/PORTUGUESE)
 313 VQT3D33 BASIC O/I 1 35EG
(GERMAN/FRENCH)
 313 VQT3D34 BASIC O/I 1 35EG
(ITALIAN/DUTCH)
 313 VQT3D35 BASIC O/I 1 35EG
(SPANISH/PORTUGUESE)
 313 VQT3D36 BASIC O/I 1 35EG
(TURKISH)
 313 VQT3D37 BASIC O/I 1 35EP
(SWEDISH/DANISH)
 313 VQT3D38 BASIC O/I 1 35EP
(POLISH/CZECH)
 313 VQT3D39 BASIC O/I 1 35EP
(HUNGARIAN/FINNISH)
 313 VQT3D40 BASIC O/I 1 35EF
(FRENCH)
 313 VQT3D41 BASIC O/I 1 35EB
(ENGLISH)
 313 VQT3D42 BASIC O/I 1 35EE
(RUSSIAN/UKRAINIAN)
 313 VQT3D32 BASIC O/I 1 25PR
(SPANISH)
 313 VQT3D43 BASIC O/I 1 25GC,GH,GF,GA
(ENGLISH/
CHINESE(TRADITIONAL))
 313 VQT3D44 BASIC O/I 1 25GC,GF
(ARABIC/PERSIAN)
 313 VQT3M09 BASIC O/I 1 25GA
(VIETNAMESE)

S-19
 S7. Exploded View
S7.1. Frame and Casing Section

21
B7

21-3 21-2 9
B8
21-1

18
19 16 9-1
20 B9
14 9-2 26

B14 2

13 B2
B3
11
B15 B10
15 17

12 33
32 3
B17
31-1
B18
25 B16
30 31
5 B19

23
1
7
4
110

106
24 105
22 27 100
109
29 107 6
28
10 108
B101
B102

104
B103
B4
8 113
102
B5 B11
114 104-1
111 104-3
B12
B106
B107 104-2
B13 112 B108 116
B104
B6 B109 115
B110 103
8-1 B111

112-2
B1
112-3
B105 112-1

S-20
S7.2. Packing Parts and Accessories Section (1)

213

211

212

220
(PC only)

208

200

206

215 204

201

202 205

214
Stick the UPC LABEL (Ref. No. 221) for
[PC] model on the original UPC place.
221
(PC only)

S-21
S7.3. Packing Parts and Accessories Section (2)

306 313

304 311

312

325
(GT only)

(DMC-FH25PR)
305
308
323
(DMC-FS35EE/EF/EG/EP
DMC-FH25GA/GF)

320
(DMC-FS35EB
DMC-FH25GC/GH) 300

319

(DMC-FH25GK/GT)

322
315
(DMC-FH25GN) 301

321 302

314

S-22