Scribd
Upload
1K views1 page

Specification For Pressure Transmitter

The document provides specifications for a pressure transmitter including: - It is an electronic smart pressure transmitter intended for use in Zone 1 hazardous areas. - It has a 4-20mA output, 24VDC power supply, weatherproof enclosure, and is accurate to within 0.075% of the span. - Several options are listed including an output meter, mounting accessories, a 2-way manifold, and zero elevation/suppression. - The transmitter is intended to measure pressure on natural gas lines ranging from 1-3 kg/cm2g at temperatures up to 65°C.

Uploaded by

Harish Gunda
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
1K views1 page

Specification For Pressure Transmitter

The document provides specifications for a pressure transmitter including: - It is an electronic smart pressure transmitter intended for use in Zone 1 hazardous areas. - It has a 4-20mA output, 24VDC power supply, weatherproof enclosure, and is accurate to within 0.075% of the span. - Several options are listed including an output meter, mounting accessories, a 2-way manifold, and zero elevation/suppression. - The transmitter is intended to measure pressure on natural gas lines ranging from 1-3 kg/cm2g at temperatures up to 65°C.

Uploaded by

Harish Gunda
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as XLS, PDF, TXT or read online on Scribd
You are on page 1/ 1

DATASHEET FOR SPECIFICATION NUMBER

SOPAN O & M CO. PVT. LTD. PRESSURE TRANSMITTER


403,SIDHARTH COMPLEX
KOTHRUD, PUNE-411029 ENQUIRY NO:
CLIENT: P.O. NO:
JOB NO: VENDOR ACCEPTANCE/DEVIATIONS
UNIT: Flow>Liquid-M3/hr Gas-SCMH Steam-kg/hr Pressure>kg/cm2g Temp>0C Level/Length->mm]
GENERAL MEASURING UNIT

Sr. No. Description Technical Requirement Sr. No. Description Technical Requirement
1 Function Transmit & Indicate 24 Service Pressure
2 Type Electronic Smart P Based 25 Element Diaphrgm
3 Case Mfg. Std. 26 Body Material Carbon Steel
4 Mounting Yoke 27 Element Material SS 316
5 Enclosure weather proof to IS2147 Explosion 28 Process Connection 1/2" NPT
Enclosure Class NEMA 4 & NEMA 7 Process Conn. Location
6 Elec. Area Class Zone-I,Gr.IIA & IIB, T3 29 Diaphragm Seal:-
7 Intrinsically safe Required Type
8 Air Supply Wetted Parts Mtl.
9 Power Supply 24 VDC Other Material
10 Cable entry 1/2" NPT(F) Process Conn.:-
11 Accuracy +0.075% of SPAN Size & Rating
12 Repeatability 0.05% Facing & Finish
TRANSMITTER Capillary Material:-
13 Output 4-20mA DC, Two wire Armour Flexible
14 Trans. power supply 24V DC Armour Flexible Mtl.
CONTROLLER Capillary Length,mm
15 Output Flush/Filling Conn. With plug
16 A/M switch MISCALLANEOUS
No. of positions 30 Over Range Protection 130% of Range
17 Set point Adj. 31 Options
18 Manual Regulator a) Output Meter W.P. Intr Safe (note2)
19 Mode b) Mounting Accessories For 2" pipe mounting
RECORDER c) 2-way Manifold Required
20 Chart d) Zero elevn. & supression Required
21 Chart Drive
22 Moving Parts Matl.
23 Chart speed

Tag. No. Operating Pressure Design Pr. Design Temp. Range Service
Nor. Max. Span Set
2-3 3 19 0-65 * * Natural Gas 3 nos
1-2 2 19 0-65 * * Natural Gas 2 nos

REV. NO. DATE ZONE BY CHECKED APPROVED

REMARK:- * VENDOR TO FURNISH THE DATA


VENDOR TO QUOTE UNIT RATE
PREPD. BY/DATE: HRG 19.1.09 TESTS AS PER APPLICABLE STD.
CHKD. BY/DATE: KSG 19.1.09
APPD. BYDATE:

You might also like