Dry-Type, Air-Core Shunt Reactors

THE PROVEN POWER.

www.trench-group.com
Introduction Shunt Reactors
Trench is a supplier of specialized electrical products and There are two general types of construction used for
a recognized world leader in the design and manufacture shunt reactors. These are referred to as dry type and
of dry type air core reactors for all utility and industrial oil immersed. The oil immersed construction typically
applications. consists of a winding and an iron core which are together
housed in a steel tank that is filled with insulating oil. The
Trench air core reactors range from small kvar units for dry type solution, on the other hand, consists only of the
applications such as capacitor bank inrush limiting or winding itself and support insulators. There is no iron core
distribution system short circuit current reduction, to large or steel tank. The insulation to ground is provided simply by
power reactors for a number of applications, such as shunt the air space around the reactor winding and the support
reactors that may be over 100 Mvar per coil. insulators. The basic dry type shunt reactor configuration is
one of single-phase units arranged with adequate clearance
between phases, connected in wye, with either a solidly-
grounded or ungrounded neutral. If required, the neutral
of shunt reactors connected to transmission lines may be
Main advantages of air-core, grounded through a reactor.

dry-type shunt reactors versus The dimensions of the winding depend on several factors.
oil immersed types As a matter of course, dimensions and weight will
increase with the reactors power (Mvar) rating. To meet
requirements for transportation and installation, the upper
n
 o environmental concern, no oil collection limits for outline dimensions of a single reactor unit are
system required in the range of 4.5 meters (14.5 feet) in both, height and
no fire hazard, no fire deluge system diameter. These dimensions translate into a maximum unit
power rating per phase of approximately 100 Mvar at
e
 ssentially no efforts and ongoing costs for
50 Hz (based on a single coil per phase). Higher ratings are
maintenance possible using multiple coils per phase. In addition to the
less civil work, lower weight basic Mvar rating, other factors such as low loss or voltage
less efforts for transport and handling requirements may also govern the design and dimensions
of the reactor. The winding length of air core shunt reactors
simplicity of insulation to ground (self healing)
is selected to meet the voltage stress imposed by the system
simple protection scheme voltage to which the reactors are connected. Shunt reactors
no risk of bushing failures which are approximately 4 m tall may be connected to
n
 o excessive magnetizing inrush current system voltages up to 110 kV, when configured in wye.
no iron core For higher voltages, two or more coils per phase may be
put in series to keep the winding voltage stresses within
typically lower investment cost acceptable limits.
less expenses for spare units (single phase unit only)
Dry type shunt reactors do not have an iron core or iron
typically shorter lead time
shield. Therefore, the magnetic field is not constrained and
will occupy the space around the reactor. Although the
magnetic field reduces in strength with increased distance
from the reactor, the presence of this field, particularly for
high power reactors, needs to be taken into consideration
for possible effects on metallic components (grounding
grids, beam structures, concrete rebar etc.) in the vicinity
of the reactor.

THE PROVEN POWER. 2

www.trench-group.com
Application of Shunt Reactors
As the name implies, shunt reactors are connected in Tertiary connected shunt reactors
a parallel (shunt) configuration to the power system
to compensate for the capacitive reactive power of
Depending on the customers requirements the reactive
transmission and distribution systems and thereby to keep
power rating of shunt reactors connected to the tertiary
the operating voltages within admissible levels.
winding of a power transformer may vary from a few Mvar
Two main applications of shunt reactors can be identified: up to approximately 100 Mvar per phase. Because of their
a) reactors that are required permanently in service for cost benefits, distribution class reactors in general and
stability reasons (especially on long transmission lines), or tertiary connected shunt reactors in particular, are usually
b) that are needed for voltage control in a meshed system of dry type design. Since the connection voltage at the
and are switched in only during light load conditions, when tertiary is 34.5 kV or less, the voltage rating of the shunt
there is an excess of capacitive reactive power. reactor is usually not a controlling factor in the selection
of the winding length. As a result the reactor may be
Depending on several factors shunt reactors may be designed with an optimum shape for minimum conductor
connected (1) either to the tertiary winding of a power length and thus for minimum cost. Such designs usually
transformer, or (2) directly to the station busbar, or (3) to constitute the most cost effective solution for reactive
transmission line terminations (3), as shown in Fig. 1. power compensation. Fig. 2 shows a distribution class
shunt reactor bank - 20 kV, 45 Mvar 3-phase, 50 Hz.

(3) (3)
(2)

(1)

Fig. 1: Shunt reactor application in power systems

Fig. 2: 20 kV, 45 Mvar 3-phase tertiary shunt reactor

THE PROVEN POWER. 3

www.trench-group.com
Shunt reactors connected to the high
voltage bus or to a high voltage line

The majority of shunt reactors which are connected directly Fig. 3 shows two 132 kV, 20 Mvar 3-phase, 60 Hz direct
to the high voltage bus or transmission line are of oil-filled connected shunt reactor banks. Each phase consists of two
type. However, a number of shunt reactors of dry type stacked sub-coils, each being about 4 m tall. As shown in
design have already been applied at voltages up to 345 kV the figure, if required, the reactors can be elevated off the
and the demand is growing. One factor driving this demand ground using support pedestals, so that live parts are not
increase is the integration of renewable generation such as accessible to station personnel.
wind parks to the grid. The connecting overhead lines or
cables require shunt compensation with ratings for reactive For higher system voltages more than two coils must be
compensation in the range of some tens of Mvars. Usually connected in series. In principle, by connecting several coils
such wind parks are located in environmentally sensitive in series, dry type shunt reactors may be applied at any
areas thereby favoring dry type air core technology. system voltage.

For dry type shunt reactors applied at sub-transmission Fig. 4 shows a shunt reactor bank for 345 kV, 20 Mvar
or transmission voltages the steady state voltage drop 3-phase, 60 Hz, consisting of two series connected reactor
along the surface of the reactor is a decisive design stacks, mounted side by side, resulting in a total of four
parameter. As mentioned earlier, reactor windings which series connected coils per phase.
are approximately 4 m tall may be connected to system
voltages up to 110 kV when connected in wye. For systems
with voltage levels above, two single units, stacked one
above the other and connected in series are required.

Fig. 3: 132 kV, 20 Mvar 3-phase shunt reactor (2 banks) Fig. 4: 345 kV, 20 Mvar 3-phase shunt reactor

THE PROVEN POWER. 4

www.trench-group.com
Wye connected shunt reactors with the
neutral grounded through a neutral reactor

The majority of faults on transmission lines are single- During normal operation, the neutral reactor is practically
phase-to-ground faults caused by flashovers of the air unloaded. In case of a SPAR operation, for less than one or
insulation. Clearing of such faults is achieved by making two seconds the reactor is loaded by typically 15 to 25 %
use of the dielectric recovery of the air. For this purpose the of the system voltage, depending on the parameters of the
affected phase of the line is temporarily isolated by opening line to which the shunt reactor is connected. The short-time
the circuit breaker at both line ends and reclosing the power rating of the neutral reactor is only a few percent of
breakers after a certain dead time. This operation is termed the shunt reactors continuous power rating.
single-phase auto-reclosing (SPAR).
Due to the advantages of dry type over oil type reactors,
Long EHV transmission lines are usually operated with practically all neutral reactors are dry type, for both oil
shunt reactors permanently connected to the lines at their immersed and dry type shunt reactors.
terminal stations, even when the lines are switched-off.
Successful SPAR on such compensated lines is hampered
by a phenomenon called secondary arcing. Instead of the
extinction of the (primary) arc, the arc is further maintained
due to capacitive and inductive coupling with the two
healthy phases. A successful auto-reclosing is achieved only
if this secondary arc extinguishes during the dead time
when the breakers are open. For mitigation of secondary
arcing it is a well proven practice to increase the zero
sequence impedance of the shunt reactor by providing
an additional single-phase reactor between the reactors
neutral and ground.

wye-connected shunt reactor

with directly grounded neutral
X0 / X1 1 Fig. 5: Air core dry type neutral
grounding reactor

Switching of shunt reactors

Switching shunt reactors is one of the most severe duties

for a circuit breaker. As a consequence, when applying
shunt reactors, whether they be dry type or oil immersed,
tertiary type or direct connected, it is extremely important
to pay particular attention to the switching device which
wye-connected shunt reactor is selected and ensure it is capable of handling the task to
with neutral grounded through a reactor which it is being applied. Guidance can be found in IEEE
X0 / X1 > 1 Std. C37.015-2009: IEEE Guide for the Application of Shunt
Reactor Switching.
X1: positive-sequence reactance of the shunt reactor
X0: zero-sequence reactance of the shunt reactor
(including the neutral reactor)

THE PROVEN POWER. 5

www.trench-group.com
Main data of Dry-Type,
Air-Core Shunt Reactors

Placement of
Phase Reactors

In line

In triangle

Table 1: Conceptual data of wye connected air-core, dry-type shunt reactors for 50 Hz systems

U Mvar X-50 Hz L I D H1 H2 H3 C M1 M2 Q
(kV) (3-phase) (ohm) (mH) (A) (mm) (mm) (mm) (mm) (mm) (kg) (kg) 75C
20 5,0 15,9 1155 3100 1100 4200 5200 1600 1900 125
10 50 2,0 6,4 2887 3300 1300 4400 5400 3200 3500 210
60 1,7 5,3 3465 3400 1450 4550 5500 3500 3800 235
20 20,0 63,7 578 3150 1350 4450 5400 1700 2000 110
20 50 8,0 25,5 1444 3350 1400 4500 5500 2900 3200 185
100 4,0 12,8 2887 3500 1900 5000 5800 5000 5600 295
20 54,5 173,3 350 2900 2050 5150 5200 2100 2400 110
33 50 21,8 69,4 875 3100 2100 5200 5600 3200 3500 180
100 10,9 34,7 1750 3200 2300 5500 5700 5100 5700 275
20 238,0 757,8 168 2900 2950 6050 6800 5500 2700 3000 95
69 50 95,3 303,1 419 3000 3000 6100 6850 5700 5000 5600 165
100 47,7 151,6 837 3400 3100 6200 6950 6300 5600 6200 220
20 605,0 1926,0 105 3100 3600 6700 7450 6200 2900 3200 85
110 40 302,5 963,0 210 3200 3650 6750 7500 6400 4200 4600 140
60 201,7 642,0 315 3250 3700 6800 7550 6500 6000 6600 170

U: rated system voltage (kV)

Mvar: reactive power (Mvar) of a bank of three single phase reactors, at rated voltage
X-50 Hz: reactance per phase (ohm)
I: rated phase current (Amps); the reactors are designed to carry continuously 105 % of rated current without exceeding the temperature class
limit
Q: quality factor (X/R) of the shunt reactor, at 75C; the numbers given in the table refer to standard reactor designs for minimum investment
cost; reactors with higher Q-factors are feasible, if required.
D, H1, H2, H3: reactor dimensions, see sketch
C: minimum distance between phase reactors mounted side-by-side, based on a coupling coefficient between reactors of less than 1 %
M1: mass per phase reactor, without support elements
M2: mass per phase reactor, including support elements

THE PROVEN POWER. 6

www.trench-group.com
Appendix Design Details of Trench
Dry-Type, Air-Core Technology
The sketch below illustrates the design concept of a Trench dry-type, air-core reactor.

1. winding

2. winding conductor

3. spider

4. terminal

5. duct stick

6. base insulator

7. mounting bracket

A dry type air core reactor consists of a cylindrical winding The winding is impregnated by epoxy resin resulting (after
(1) made of one or several concentric layers of film/glass curing) in a mechanically strong and compact unit. The
tape insulated aluminum conductor (2). All layers are reactors are mounted on several base insulators (6) and
electrically connected in parallel by welding their top and according mounting brackets (7).
bottom ends to metallic cross arms, commonly referred
to as spiders (3). Each spider carries a terminal (4) for
electrical connection of the reactor. The individual layers
are configured such that radial voltage stress is virtually
nil and the remaining axial voltage stress results in surface
stress values that are less than those on porcelain insulators
and turn-to-turn steady state operating voltages that are
well below the level at which partial discharges can occur.
All layers are radially spaced by several glass fiber sticks
(5) which form air ducts necessary for the cooling of the
winding. Cooling is provided by natural convection of
ambient air, which enters at the bottom end of the winding
and exits at its top end.

THE PROVEN POWER. 7

www.trench-group.com
Trench Factories
Trench Austria GmbH Trench High Voltage Products Ltd.,
Paschinger Strasse 49 Shenyang
Postfach 13 No. 2 Zhengliang Er. Road
A-4060 Linz-Leonding Jing Shen Xi San Street
Austria Dao Yi Economic Development Zone
Phone: +43-732-6793-0 Shenyang 110136 P. R. China
Fax: +43-732-671341 Phone: +86-24-89722688
Fax: +86-24-289737200
Trench Brasil Ltda
Via Expressa de Contagem, 2685 Trench Italia S.r.l.
Contagem, Minas Gerais Strada Curagnata, 37
CEP 32370-485 IT-17014 Bragno
Brazil Cairo, Montenotte (SV)
Phone: +55-31-3391-5959 Italy
Fax: +55-31-3391-1828 Phone; +39-019-5161-111
Fax: +39-019-5161-401
Trench China
MWB (Shanghai) Co., Ltd. Trench Limited
No. 3658, Jiancheng Road Coil Products Division
Minhang, Shanghai 71 Maybrook Drive
P. R. China Scarborough, Ontario
200245 Canada M1V 4B6
Phone: +86-21-54720088 Phone: +1-416-298-8108
Fax: +86-21-54723118 Fax: +1-416-298-2209
Trench France S.A. Trench Limited
16, Rue du Gnral Cassagnou Instrument Transformer Division
B.P. 70 F-68 302 1865 Clements Road
St. Louis, Cedex Pickering, Ontario
France Canada L1W 3R8
Phone : +33-3-89-70-2323 Phone: +1-416-751-8570
Fax : +33-3-89-67-2663 Fax: +1-416-751-6952
Trench Germany GmbH Trench Limited
Nrnberger Strasse 199 Power Line Carrier Division
D-96050 Bamberg 330 Finchdene Square
Germany Scarborough, Ontario
Phone: +49-951-1803-0 Canada M1X 1A5
Fax: +49-951-1803-224 Phone: +1-416-847-5400
Fax: +1-416-291-5581

The Trench Group is your partner of choice for electrical

power transmission and distribution solutions today and
for the development of your new technology solutions
of tomorrow.

THE PROVEN POWER.

www.trench-group.com