ANSI Valves

COMPANY HISTORY
1960
1990 Pipe Hangers
1961 and Brackets
Business Started 1991
1962 from Grey Iron Pot
1963 1992
1964 Self Export, Developped US

1993
and European Market
1965
1994
1966
1967 1995
1968
1996
1969
Steel Pipe Nipples
Malleable Iron Pipe 1997
Red Brass Pipe Nipples
1970 Fittings
1971 1998
1972
1999
1973
Ductile Iron Grooved Fittings
2000
1974 Bronze Fittings, Ball Valves
1975 2001
Malleable Iron Pipeclamp
1976 Fittings 2002
1977
2003
1978
1979 2004
1980 2005
1981
Ductile Iron Pipe 2006
1982 Fittings
1983 2007 Electric Power Fittings
1984 2008
1985
2009
1986
Export, Main Market: 2010
1987 Southeast Asia
1988 Valve Business
2011
Development
1989 Cast Iron Fittings
Extra-heavy
2012 Brass Pipe Nipples
Steel Pipe
2013 Development
AMERICAN VALVES
AWWA C515 Flanged Resilient OS&Y

AWWA Resilient Wedge
Gate Valve (Z41X),
Gate Valve 300PSI, UL/FM Approved
Statement:
Gate valves serve to cut the medium flow in the piping system, widely used in the field of
potable water, water supply and drainage, sewage disposal, irrigation, air conditioning, fire
protection as well as chemical and energy industry.
Features:
1. Material:
Ductile Iron ASTM A536, 65-45-12
Body, bonnet, wedge, handwheel and operating nut are all produced in ductile iron material
which provides guarantee for high strength and good corrosion resistance.
2. Triple O-ring Stem Seals
The lower O-ring isolates the stem thrust collar bearing area from the waterway. The upper two
O-rings can easily be replaced in the line while the valve is under pressure in the open position.
MATERIAL SPECIFICATION
3. Stainless Steel Stem, Brass Thrust Collar and Bronze Wedge Nut
Part No. Part Standard Specication Options
This life-tested MEIDE design has repeatedly proven its superior strength and abrasive
1 Valve Body ASTM A536,65-45-12
resistance.
2 Resilient Wedge Disc ASTM A536,65-45-12+EPDM
4. Fusion Bonded Epoxy Coating
AISI 304, AISI 431, AISI 316,
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior and 3 Stem AISI 420
Al-bronze
Body, Bonnet, Wedge & Operating
exterior surface which provides reliable corrosion resistance. Z41X 4 Bonnet Gasket EPDM NBR
Nut in Ductile Iron
5. Long Service Life with Resilient Seat Cycling Test 1,000 times 5 Bonnet ASTM A536,65-45-12
Triple O-ring Stem Seals
The Valve has been subjected to 1,000 cycles of operation at a maximum rate of 6 cycles of 6 Washer Brass Hpb59-1
operation per minute from fully closed to fully open and from fully open to fully closed positions Stainless Steel Stem and Brass Thrust Collar
under cycled hydrostatic pressure. Bronze Alloy Wedge Nut Connection Ends: Flange to ASME B16.1 7 Yoke ASTM A536,65-45-12
Working Pressure: 300PSI 8 Stem Bushing Brass Hpb59-1

Fusion Bonded Epoxy Coating
200PSI and 250PSI available upon request 9 Gland ASTM A536,65-45-12
10 Stem Nut Brass Hpb59-1 Bronze ZQSn5-5-5
Temperature Range: 0- 80
11 Handwheel ASTM A536,65-45-12 Pressed Steel
Coating: Fusion Bonded Epoxy Coating in accordance with 12 Washer Brass Hpb59-1
ANSI/AWWA C550
13 Gland Nut Carbon Steel Zinc Plated AISI 304, AISI 316
14 Stud Carbon Steel Zinc Plated AISI 304, AISI 316
15 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316
16 Nut Carbon Steel Zinc Plated AISI 304, AISI 316
17 O-Ring EPDM NBR
Note: For special material request other than standard specication, please indicate clearly on the inquiry
or order list.
Z41X Z45X Z45XC-2 Z81X DN Dimensions(mm)
Flanged Resilient OS&Y Flanged Resilient NRS Flanged Resilient NRS Grooved Resilient OS&Y
Gate Valve Inch mm L H1(Close) H2(Open) D D1 C n-L
Gate Valve Gate Valve with Post Flange Gate Valve
Page 11 Page 12 Page 13 2" 50 178 318 370 152 120.7 16 4-19.1
Page 14
2.5" 65 190 343 410 178 139.7 17.5 4-19.1
3" 80 203 386 468 191 152.4 19.1 4-19.1
XZ41X 4" 100 229 436 538 229 190.5 19.1 8-19.1
5" 125 254 516 640 254 215.9 19.1 8-22.2
6" 150 267 576 730 279 241.3 19.1 8-22.2
8" 200 292 749 950 343 298.5 22.2 8-22.2
10" 250 330 904 1158 406 362 23.8 12-25.4
12" 300 356 1030 1335 483 431.8 25.4 12-25.4
CLX XZA SMC

Gear Drive Details for electric drive available upon request.
Z85X Z35XC
Grooved Resilient NRS Mechanical Resilient OS&Y
Gate Valve Gate Valve
Page 15 Page 16
10 11
AMERICAN VALVES
AWWA C515 Flanged Resilient NRS AWWA C515 Flanged Resilient NRS
Gate Valve (Z45X), Gate Valve with Post Flange
300PSI, UL/FM Approved (Z45XC-2), 300PSI
MATERIAL SPECIFICATION MATERIAL SPECIFICATION

Part No. Part Standard Specication Options Part No. Part Standard Specication Options
1 Valve Body ASTM A536,65-45-12 1 Valve Body ASTM A536,65-45-12
2 Resilient Wedge Disc ASTM A536,65-45-12+EPDM 2 Resilient Wedge Disc ASTM A536,65-45-12+EPDM
Z45X AISI 304, AISI 316, AISI 420, Z45XC-2 AISI 304, AISI 316, AISI 420,
3 Stem AISI 431 3 Stem AISI 431
Al-bronze Al-bronze
4 Bonnet Gasket EPDM NBR Connection Ends: Flange to ASME B16.1 4 Bonnet Gasket EPDM NBR
5 Bonnet ASTM A536,65-45-12 5 Bonnet ASTM A536,65-45-12
Working Pressure: 300PSI
Connection Ends: Flange to ASME B16.1 6 O-Ring NBR EPDM 6 O-Ring NBR EPDM
200PSI and 250PSI available upon request
Working Pressure: 300PSI 7 Gland ASTM A536,65-45-12 7 Gland ASTM A536,65-45-12
200PSI and 250PSI available upon request 8 Handwheel ASTM A536,65-45-12 Pressed Steel 8 Post Flange ASTM A536,65-45-12
9 Bolt Carbon Steel Zinc Plated AISI 304, AISI 316 Coating: Fusion Bonded Epoxy Coating in accordance with 9 Square Operating Nut ASTM A536,65-45-12
ANSI/AWWA C550
10 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316 10 Bolt Carbon Steel Zinc Plated AISI 304, AISI 316
Coating: Fusion Bonded Epoxy Coating in accordance with
ANSI/AWWA C550 11 Ring Wiper EPDM NBR 11 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316
12 O-Ring NBR EPDM 12 Nut Carbon Steel Zinc Plated AISI 304, AISI 316
13 Nut Carbon Steel Zinc Plated AISI 304, AISI 316 13 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316
14 Axis Guide Brass Hpb59-1 14 Ring Wiper EPDM NBR
15 Washer Brass Hpb59-1 15 O-Ring NBR EPDM
16 O-Ring NBR EPDM 16 Axis Guide Brass Hpb59-1
17 Nut Carbon Steel Zinc Plated AISI 304, AISI 316 17 Washer Brass Hpb59-1
18 Wedge Nut Brass Hpb59-1 Bronze ZQSn5-5-5 18 O-Ring NBR EPDM
Note: For special material request other than standard specication, please indicate clearly on the inquiry 19 Nut Carbon Steel Zinc Plated AISI 304, AISI 316
or order list. 20 Wedge Nut Brass Hpb59-1 Bronze ZQSn5-5-5
or order list.
DN Dimensions(mm)
DN Dimensions(mm)
Z45XC Inch mm L H(Z45X) H(Z45XC) D D1 C n-L
Inch mm L H D D1 C n-L
2" 50 178 254 278 152 120.7 16 4-19.1
4" 100 229 395 229 190.5 19.1 8-19.1
2.5" 65 190 275 300 178 139.7 17.5 4-19.1
5" 125 254 432 254 215.9 19.1 8-22.2
3" 80 203 301 321 191 152.4 19.1 4-19.1
6" 150 267 475 279 241.3 19.1 8-22.2
4" 100 229 355 375 229 190.5 19.1 8-19.1
8" 200 292 585 343 298.5 22.2 8-22.2
5" 125 254 393 415 254 215.9 19.1 8-22.2
10" 250 330 656 406 362 23.8 12-25.4
6" 150 267 448 455 279 241.3 19.1 8-22.2
12" 300 356 751 483 431.8 25.4 12-25.4
8" 200 292 548 565 343 298.5 22.2 8-22.2
10" 250 330 626 636 406 362 23.8 12-25.4
12" 300 356 722 731 483 431.8 25.4 12-25.4
12 13
AMERICAN VALVES
AWWA C515 Grooved Resilient OS&Y AWWA C515 Grooved Resilient NRS
Gate Valve (Z81X), 300PSI Gate Valve (Z85X), 300PSI

Part No. Part Standard Specication Options Part No. Part Standard Specication Options
1 Valve Body ASTM A536,65-45-12 1 Valve Body ASTM A536,65-45-12
2 Resilient Wedge Disc ASTM A536,65-45-12+EPDM Z85X 2 Resilient Wedge Disc ASTM A536,65-45-12+EPDM
Z81X 3 Stem AISI 420
3 Stem AISI 431
Al-bronze Connection Ends: Groove to AWWA C606 Al-bronze
Connection Ends: Groove to AWWA C606 4 Bonnet Gasket EPDM NBR 4 Bonnet Gasket EPDM NBR
5 Bonnet ASTM A536,65-45-12 5 Bonnet ASTM A536,65-45-12
Working Pressure: 300PSI 200PSI and 250PSI available upon request
200PSI and 250PSI available upon request 6 Washer Brass HPb59-1 6 O-Ring NBR EPDM
7 Yoke ASTM A536,65-45-12
Temperature Range: 0- 80 7 Gland ASTM A536,65-45-12
8 Stem Bushing Brass HPb59-1 Coating: Fusion Bonded Epoxy Coating in accordance with 8 Handwheel ASTM A536,65-45-12 Pressed Steel
Coating: Fusion Bonded Epoxy Coating in accordance with 9 Gland ASTM A536,65-45-12 ANSI/AWWA C550 or painting upon request 9 Bolt Carbon Steel Zinc Plated AISI 304, AISI 316
ANSI/AWWA C550 or painting upon request
10 Stem Nut Brass HPb59-1 Bronze ZQSn5-5-5 10 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316
11 Handwheel ASTM A536,65-45-12 Pressed Steel 11 Ring Wiper EPDM NBR
12 Washer Brass HPb59-1 12 O-Ring NBR EPDM
13 Gland Nut Carbon Steel Zinc Plated AISI 304, AISI 316 13 Nut Carbon Steel Zinc Plated AISI 304, AISI 316
14 Stud Carbon Steel Zinc Plated AISI 304, AISI 316 14 Axis Guide Brass HPb59-1
15 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316 15 Washer Brass HPb59-1
16 Nut Carbon Steel Zinc Plated AISI 304, AISI 316 16 O-Ring NBR EPDM
17 O-Ring EPDM NBR 17 Nut Carbon Steel Zinc Plated AISI 304, AISI 316
Note: For special material request other than standard specication, please indicate clearly on the inquiry 18 Wedge Nut Brass HPb59-1 Bronze ZQSn5-5-5
or order list.
DN Dimensions(mm) or order list.
Inch mm L H1(Close) H2(Open) OD d A B DN Dimensions(mm)
2" 50 178 318 370 60.3 57.15 15.88 7.92 Z55X Inch mm L H OD d A B
2.5" 65 190 343 410 73 69.09 15.88 7.92 2" 50 178 254 60.3 57.15 15.88 7.92
3" 80 203 386 468 88.9 84.94 15.88 7.92 2.5" 65 190 275 73 69.09 15.88 7.92
4" 100 229 436 538 114.3 110.08 15.88 9.52 3" 80 203 301 88.9 84.94 15.88 7.92
5" 125 254 516 640 141.3 137.03 15.88 9.52 4" 100 229 355 114.3 110.08 15.88 9.52
6" 150 267 576 730 168.3 163.96 15.88 9.52 5" 125 254 393 141.3 137.03 15.88 9.52
8" 200 292 749 950 219.1 214.4 19.05 11.13 6" 150 267 448 168.3 163.96 15.88 9.52
10" 250 330 904 1158 273 268.28 19.05 12.7 8" 200 292 548 219.1 214.4 19.05 11.13
12" 300 356 1030 1335 323.9 318.29 19.05 12.7 10" 250 330 626 273 268.28 19.05 12.7
12" 300 356 722 323.9 318.29 19.05 12.7
14 15
AMERICAN VALVES
AWWA C515 Mechanical Resilient NRS Vertical Indicator Post (IP)

Gate Valve (Z35XC), 300PSI Statement:
Vertical indicator post provides a means to operate a buried or
otherwise inaccessible valve and able to indicate the open or shut
position of the valve.
Coating:
Fusion Bonded Epoxy Coating in accordance with ANSI/AWWA C550 MATERIAL SPECIFICATION
Part No. Part Standard Specication
1 Hex Nut Carbon Steel Zinc Plated
2 Hex Bolt Carbon Steel Zinc Plated
3 Socket ASTM A536,65-45-12
4 Cotter Pin AISI 304
5 Base Flange Cast Iron ASTM A126 Class B
6 Hex Bolt Carbon Steel Zinc Plated
7 Hex Nut Carbon Steel Zinc Plated
8 Standpipe Carbon Steel ASTM A53
MATERIAL SPECIFICATION 9 Stem 1" Square Carbon Steel AISI 1045
Part No. Part Standard Specication Options 10 Body Cast Iron ASTM A126 Class B
1 Valve Body ASTM A536,65-45-12 11 Locking Wrench ASTM A536,65-45-12
2 Resilient Wedge Disc ASTM A536,65-45-12+EPDM 12 Target Carrier Nut Cast Aluminum
Z35XC AISI 304, AISI 316, AISI 420,
3 Stem AISI 431 13 Hex Bolt Carbon Steel Zinc Plated
Al-bronze
Connection Ends: Mechanical Joint to ANSI/AWWA C153/A21.53 14 Hex Nut Carbon Steel Zinc Plated
4 Bonnnet Gasket EPDM NBR
Working Pressure: 300PSI 5 Bonnnet ASTM A536,65-45-12 15 Hex Bolt Carbon Steel Zinc Plated
200PSI and 250PSI available upon request 16 Target Cast Aluminum
6 O-Ring NBR EPDM
Temperature Range: 0- 80 7 Gland ASTM A536,65-45-12 17 Window Class Plexiglass
Coating: Fusion Bonded Epoxy Coating in accordance with 8 Square Operating Nut ASTM A536,65-45-12 18 Gasket PTFE
ANSI/AWWA C550 9 Bolt Carbon Steel Zinc Plated AISI 304, AISI 316 19 Operating Nut AISI 304
10 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316 20 Top Section Cast Iron ASTM A126 Class B
11 Ring Wiper EPDM NBR 21 Snap Ring AISI 1066
12 O-Ring NBR EPDM 22 Plug Malleable Iron
13 Nut Carbon Steel Zinc Plated AISI 304, AISI 316 23 Square Nut Carbon Steel Zinc Plated
14 Axis Guide Brass HPb59-1 24 Hex Bolt Carbon Steel Zinc Plated
15 Washer Brass HPb59-1
Field Adjustment:
16 O-Ring NBR EPDM
17 Nut Carbon Steel Zinc Plated AISI 304, AISI 316
1.Remove the Top Section from the top of the Indicator Post assembly;
18 Wedge Nut Brass HPb59-1 Bronze ZQSn5-5-5 2.Cut the required stem length and adjust the Standpipe to match up
to the ground line;
Z35XC-2 Z05XC or order list. 3.Set the "OPEN" and "SHUT" targets for the appropriate valve size;
4.Reattach the Top Section to the top of the Indicator Post assembly.
DN Dimensions(mm)
Inch mm L H D D1 E F C n-L
2" 50 203 278 152 120.6 89 66.3 16 2-19.1
3" 80 229 321 195 157 125.5 103.1 19.1 4-19.1
4" 100 229 375 232 190.5 152.9 124.5 19.1 4-22.2
6" 150 292 455 282 241.3 206.2 177.8 19.1 6-22.2
8" 200 318 565 340 298 260.9 232.4 22.2 6-22.2
10" 250 375 636 397 355.6 313.4 284.4 23.8 8-22.2
12" 300 378 731 454 412.7 366.7 337.8 25.4 8-22.2
16 17
AMERICAN VALVES
MSS SP-67 Resilient Centerline MSS SP-67 Wafer Buttery Valve
Buttery Valve (D71X4, D371X4, XD371X4),

250PSI
Statement:
Resilient centerline buttery valves usually serve to cut off medium ow in the piping system,
widely applied in the field of potable water, water supply and drainage, sewage disposal,
irrigation, air conditioning, re protection as well as chemical and energy industry. The design of
the buttery valves, however, makes it also suitable to serve as adjusting valve.
Features:
1. Material:
Body and lever are all produced in ductile iron material (ASTM A536, 65-45-12) which provides
guarantee for high strength and good corrosion resistance.
Different options of the disc and seat, e.g. disc of DI nickel or nylon 11 coated, different series of Part No. Part Standard Specication Options
stainless steel, Al-bronze, seat in EPDM, NBR or Fluororubber, makes it suitable to be applied 1 Valve Body ASTM A536,65-45-12
under different working conditions. NBR/Fluororubber & Backing;
2 Seat EPDM & Backing EPDM/NBR Vulcanized on Valve Body;
2. Design: Soft Seat in EPDM/NBR;
Universal ange connection to EN 1092 PN6/10/16, ANSI B16.1 CLASS 125/150, GB9113, JIS 3 Disc ASTM A536,65-45-12 AISI 304, AISI 316, AL-Bronze UNC 95400
B2112 10K, AS 2129 Table E, BS 10 Table D/E.
4 Stem AISI 420 AISI 304, AISI 316, AISI 416, AISI 431
Different options of operation including lever handle, gear box, gear box with tamper switch,
5 O-Ring NBR EPDM
electric drive, and pneumatic drive, etc. D71X4
Different options of rubber seat including insert rubber seat, rubber vulcanized on valve body 6 Bushing Nylon 1010 PTFE
and boot rubber seat. Ductile Iron Lever and Body Design Standard: MSS SP-67 7 Lever ASTM A536,65-45-12 Aluminum
3. Coating Stainless Steel Stem Connection Ends: ASME B16.1 Note: For special material request other than standard specication, please indicate clearly on the inquiry
Fusion bonded epoxy coating of valve body and lever provides reliable corrosion resistance. Fusion Bonded Epoxy Coating or order list.
Top Flange Standard: ISO 5211
To achieve higher corrosion resistance, factory is also able to supply Nylon 11 coated disc. Disc: DI, Stainless Steel or Al-bronze Stem drive by keys, parallel or diagonal square or at head
Nylon 11 coating is thermoplastic plant coating approved by USDA with high corrosion
Seat: EPDM/NBR/Fluororubber with backing Working Pressure: 250PSI
resistance and antisepsis which can be applied where there is strict requirement for anti-
corrosion. 175PSI, 200PSI and 300PSI available upon request
ANSI/AWWA C550
D371X4 XD371X4
DN Dimensions(mm)
Inch mm A B C D D1 V 2 N- G L ISO 5211
1.5" 40 138 64.5 33 43.9 98.6 32 12.6 4-15.9 9.45 267 F07
2" 50 140.5 64.5 43 53.9 120.7 32 14 4-19 9.53 267 F07
D71X4 D71XL4 D41X4 D81X4 2.5" 65 153 72 46 65.2 139.7 32 14 4-19 9.53 267 F07
Wafer Buttery Valve Lugged Wafer Buttery Valve Flanged Buttery Valve Grooved Buttery Valve 3" 80 157.5 86 46 79.7 152.4 32 14 4-19 9.53 267 F07
Page 19 Page 20 Page 21 Page 22 4" 100 176 100 52 105 190.5 32 16 8-19 11.14 267 F07
5" 125 191 112 56 130 215.9 32 16 8-22 11.14 267 F07
6" 150 202.5 128 56 156 241.3 32 20 8-22 12.7 267 F07
8" 200 243.5 162 60 206.7 298.5 45 26 8-22 20.6 356 F10
10" 250 273 194 68 253.3 362 45 26 12-25 20.6 356 F10
12" 300 311 223 78 301.9 431.8 45 28 12-25 22.1 490 F10
14" 350 340 267 78 333.9 476.3 45 31.6 12-28.5 22.1 - F12
Details for electric drive available upon request. 16" 400 400 300 102 389.6 539.8 48 33.2 16-28.5 27 - F14
18 19
AMERICAN VALVES
MSS SP-67 Lugged Wafer API 609 Flanged Buttery Valve

Buttery Valve (D71XL4, D371XL4), (D41X4, D341X4),
250PSI 250PSI
NBR/Fluororubber & Backing;
2 Seat EPDM & Backing EPDM/NBR Vulcanized on Valve Body; 1 Valve Body ASTM A536,65-45-12
Soft Seat in EPDM/NBR;
3 Disc ASTM A536,65-45-12 AISI 304, AISI 316, AL-Bronze UNC 95400 2 Seat EPDM NBR
4 Stem AISI 420 AISI 304, AISI 316, AISI 416, AISI 431 D41X4 3 Disc ASTM A536,65-45-12 AISI 304, AISI 316, AL-Bronze UNC 95400
D71XL4
5 O-Ring NBR EPDM
4 Stem AISI 420 AISI 304, AISI 316, AISI 416, AISI 431
Design Standard: MSS SP-67 Design Standard: API 609
6 Bushing Nylon 1010 PTFE
Connection Ends: ASME B16.1 5 O-Ring NBR EPDM
7 Lever ASTM A536,65-45-12 Aluminum Face to Face: ISO 5752 Series 13
Top Flange Standard: ISO 5211 Connection Ends: ASME B16.1 6 Bushing Nylon 1010 PTFE
Stem drive by keys, parallel or diagonal square or at head or order list. 7 Lever ASTM A536,65-45-12 Aluminum
Working Pressure: 250PSI Stem drive by keys, parallel or diagonal square or at head Note: For special material request other than standard specication, please indicate clearly on the inquiry
175PSI, 200PSI and 300PSI available upon request or order list.
Temperature Range: 0- 80 175PSI, 200PSI and 300PSI available upon request
Coating: Fusion Bonded Epoxy Coating in accordance with Temperature Range: 0- 80
ANSI/AWWA C550
Coating: Fusion Bonded Epoxy Coating inaccordance with
ANSI/AWWA C550
DN Dimensions(mm)
Inch mm A B C D D1 V 2 NXM G L ISO 5211
2" 50 140.5 64.5 43 53.9 120.7 32 14 4X5/8" 9.53 267 F07
2.5" 65 153 72 46 65.2 139.7 32 14 4X5/8" 9.53 267 F07
3" 80 157.5 86 46 79.7 152.4 32 14 4X5/8" 9.53 267 F07
4" 100 176 100 52 105 190.5 32 16 8X5/8" 11.14 267 F07
5" 125 191 112 56 130 215.9 32 16 8X3/4" 11.14 267 F07 D341X4
6" 150 202.5 128 56 156 241.3 32 20 8X3/4" 12.7 267 F07
8" 200 243.5 162 60 206.7 298.5 45 26 8X3/4" 20.6 356 F10 DN Dimensions(mm)
ISO
10" 250 273 194 68 253.3 362 45 26 12X7/8" 20.6 356 F10 Inch mm L1 H1 H2 H3 A B C n-1 D E K n-2 F G L
5211
D371XL4 12" 300 311 223 78 301.9 431.8 45 28 12X7/8" 22.1 490 F10 2" 50 108 80 110 32 150 17.5 120.7 4-19 53.9 70 90 4-10 F07 14 9.53 267
14" 350 340 267 78 333.9 476.3 45 31.6 12X1" 22.1 - F12 2.5" 65 112 80 131 32 180 22.3 139.7 4-19 65.2 70 90 4-10 F07 14 9.53 267
3" 80 114 95 134 32 190 22.3 152.4 4-19 79.7 70 90 4-10 F07 14 9.53 267
4" 100 127 113 150 32 230 22.3 190.5 8-19 105 70 90 4-10 F07 16 11.14 267
5" 125 140 114 170 32 255 22.3 215.9 8-22 130 70 90 4-10 F07 16 11.14 267
6" 150 140 139 180 32 280 23.9 241.3 8-22 156 70 90 4-10 F07 20 12.7 267
8" 200 152 175 210 45 345 27 298.5 8-22 206.7 102 125 4-12 F10 26 20.6 356
10" 250 165 203 245 45 405 28.6 362 12-25 253.3 102 125 4-12 F10 26 20.6 356
12" 300 178 242 276 45 485 30.2 431.8 12-25 301.9 102 125 4-12 F10 28 22.1 490
14" 350 190 250 328 45 535 33.4 476.3 12-28.6 333.5 125 150 4-14 F12 31.6 22.1 -
16" 400 216 277 376 51 595 35 539.8 16-28.6 389.6 140 175 4-18 F14 33.15 27 -
18" 450 222 295 407 51 635 38.1 577.9 16-31.8 440.5 140 175 4-18 F14 38 27 -
20" 500 229 330 448 64 700 41.3 635 20-31.8 491.6 140 175 4-18 F14 41.15 27 -
24" 600 267 420 518 70 815 46.1 749.3 20-35 592.5 165 210 4-22 F16 50.65 - -
28" 700 292 450 560 66 927 71.3 863.6 28-35 695 254 300 8-18 F25 63.5 - -
32" 800 318 501 620 66 1060 81 977.9 28-41 794.7 254 300 8-18 F25 63.5 - -
20 21
AMERICAN VALVES
MSS SP-67 Grooved Buttery Valve Buttery Valve Performance Data

(D81X4, D381X4, XD381X4), Cv = Flow Coefcient
Formulas for Cv Values: Cv=Q/(P)0.5
250PSI Q = Flow Rate (gal/min)
P = Pressure Drop Across Valve (1bf/in2)
Kv=Cv/1.156
1 Valve Body ASTM -A536,65-45-12
2 Disc ASTM A536,65-45-12+EPDM or NBR
3 O-Ring NBR EPDM

D81X4 4 Stem AISI 431 AISI 304, AISI 316, AISI 416
Design Standard: MSS SP-67 5 O-Ring NBR EPDM
Connection Ends: Groove to AWWA C606 Flow Rate Q (gal/min)
6 Stem AISI 431 AISI 304, AISI 316, AISI 416
7 Lever ASTM A536,65-45-12 Aluminum Inch 2.5'' 5'' 6'' 10'' 12''
Stem drive by keys, parallel or diagonal square or at head DN
2'' 3'' 4'' 8''
Note: For special material request other than standard specication, please indicate clearly on the inquiry mm 50 65 80 100 125 150 200 250 300
Working Pressure: 250PSI or order list.
175PSI, 200PSI and 300PSI available upon request Inch 2.06 2.50 3.06 4.06 5.04 6.06 8.06 9.90 11.81
Pipe Diameter
Temperature Range: 0- 80 mm 52.40 63.50 77.80 103.00 128.00 154.00 204.80 251.35 299.95
Coating: Fusion Bonded Epoxy Coating in accordance with Flow Cv 284.55 417.87 512.16 897.67 1200.59 1737.86 3073.50 4140.73 5896.80
Coefcient
ANSI/AWWA C550 or painting upon request (Fully Open) Kv 246.15 361.48 443.04 776.53 1038.57 1503.34 2658.74 3581.95 5101.04
D381X4 XD381X4
DN Dimensions(mm)
ISO
Inch mm L1 L2 L3 B C D E K N-1 H1 H2 H3 2 G
5211
2" 50 81 15.9 7.9 57.15 60.3 50.3 70 90 4-10 65 89 32 14 9.53 F07
2.5" 65 97 15.9 7.9 69.09 73 60.8 70 90 4-10 71 102 32 14 9.53 F07
3" 80 97 15.9 7.9 84.94 88.9 76 70 90 4-10 81 109 32 14 9.53 F07
4" 100 116 15.9 9.5 110.08 114.3 98.5 70 90 4-10 95 128 32 16 11.14 F07
5" 125 148 15.9 9.5 137.03 141.3 122.4 70 90 4-10 111 141 32 16 11.14 F07
6" 150 148 15.9 9.5 163.96 168.3 148 70 90 4-10 133 153 32 20 12.7 F07
8" 200 133 19.1 11.1 214.4 219.1 199 102 125 4-12 164 184 45 26 20.6 F10
10" 250 159 19.1 12.7 268.28 273 252 102 125 4-12 196 216 45 31.6 22.1 F10
12" 300 165 19.1 12.7 318.29 323.9 300.5 102 125 4-12 226 254 45 33.1 27 F10
Note: Valve must not be installed with disc in full open position. Disc must be partly closed so that no part is protruding beyond end of valve body.
22 23
AMERICAN VALVES
AWWA Check Valve AWWA C508 Swing Check Valve

(H44X2), 300PSI, FM Approved
Statement:
Check valves serve to prevent the backflow of medium in the piping system for
protection of important equipments, widely used in the eld of potable water, water
supply and drainage, sewage disposal, irrigation, air conditioning, re protection as
well as chemical and energy industry.
Features:
1. Material: Ductile Iron ASTM A536, 65-45-12
Valve body, bonnet, disc are all produced in ductile iron material which provides
guarantee for high strength and good corrosion resistance.
2. Fusion Bonded Epoxy Coating
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior
and exterior surface which provides reliable corrosion resistance. Part No. Part Standard Specication Options
3. Small Hydraulic Friction Loss with Reasonable Structure Design
H44X2 2 Bonnet ASTM A536,65-45-12
Body & Bonnet: Ductile Iron
3 Eye Bolt Carbon Steel Zinc Plated
Disc: D.I.+EPDM or D.I. + Bronze
4 O-Ring NBR EPDM
or Stainless Steel Sealing
5 Hinge Pin AISI 304
Bronze or Stainless Steel Seat Connection Ends: Flange to ASME B16.1
6 Hinge Bushing Brass ASTM B36
Fusion Bonded Epoxy Coating Working Pressure: 300PSI AISI 304, AISI 316 Pressed Fit
7 Seat Ring Bronze ASTM B62 (Pressed Fit)
200PSI and 250PSI available upon request or Threaded
8 Disc Seat Bolt AISI 304
9 Retainer Washer Bronze ASTM B62
Coating: Fusion Bonded Epoxy Coating in accordance with AISI 304, AISI 316,
10 Disc Sealing Ring EPDM
ANSI/AWWA C550 Bronze ASTM B62
11 Disc ASTM A536,65-45-12
12 Clapper Arm ASTM A536,65-45-12
13 Stud Bushing Brass ASTM B36
14 O-Ring NBR EPDM
H44X2 H44X H44XW H84X 15 Nut AISI 304 AISI 316
Swing Check Valve Swing Check Valve Swing Check Valve with Weight & Lever Grooved Resilient Swing Check Valve
Page 25 Page 26 Page 27 Page 28 or order list.
DN Dimensions(mm)
Inch mm L D D1 b n-d H
2" 50 203 152 120.5 16 4-19.1 133
2.5" 65 254 178 139.5 17.5 4-19.1 150
3" 80 278 191 152.5 19 4-19.1 243
4" 100 330 229 190.5 24 8-19.1 284
6" 150 406 279 241.5 25.5 8-22.2 290
8" 200 495 343 298.5 28.5 8-22.2 330
H44J HC41X DH77X
10" 250 622 406 362 30.5 12-25.4 350
Rubber Disc Swing Check Valve Silent Check Valve Double Door Wafer Check Valve
Page 29 Page 30 Page 31 12" 300 660 483 432 32 12-25.4 376
24 25
AMERICAN VALVES
AWWA C508 Swing Check Valve AWWA C508 Swing Check Valve
(H44X/H44T), with Weight & Lever (H44XW),
300PSI 200PSI
1 Valve Body Cast Iron A126 CL B ASTM A536, 65-45-12
AISI 304, AISI 316 Pressed Fit
2 Seat Ring Bronze ASTM B62 (Pressed Fit)
or Threaded
MATERIAL SPECIFICATION 3 Disc ASTM A536,65-45-12
AISI 304, AISI 316,
H44X Part No. Part Standard Specication Options H44XW 4 Disc Sealing Ring EPDM
Bronze ASTM B62
1 Valve Body ASTM A536,65-45-12 5 Bolt AISI 304 AISI 316
Connection Ends: Flange to ASME B16.1
AISI 304, AISI 316 Pressed Fit 6 Clapper Arm ASTM A536,65-45-12
Connection Ends: Flange to ASME B16.1 2 Seat Ring Brass HPb59-1 (Pressed Fit)
or Threaded Working Pressure: 200PSI 7 Bonnet Gasket EPDM
Working Pressure: 300PSI 3 Disc ASTM A536,65-45-12 250PSI and 300PSI available upon request 8 Bonnet Cast Iron A126 CL B ASTM A536, 65-45-12
4 Clapper Arm ASTM A536,65-45-12 Temperature Range: 0- 80 9 Bolt Carbon Steel Zinc Plated AISI 316
Temperature Range: Rubber Seal: 0- 80, AISI 304, AISI 316, 10 Weight Cast Iron A126 CL B ASTM A536, 65-45-12
5 Disc Sealing Ring EPDM Coating: Fusion Bonded Epoxy Coating in accordance with
Metal Seal: -10- 350 Bronze ASTM B62 ANSI/AWWA C550 11 Lever Carbon Steel Zinc Plated
Coating: Fusion Bonded Epoxy Coating in accordance with 6 Hinge Pin Stainless Steel 13Cr 12 Nut Brass ASTM B36
ANSI/AWWA C550 or painting upon request 7 Bonnet Gasket EPDM Graphite+Steel 13 O-Ring NBR EPDM
8 Bonnet ASTM A536,65-45-12 14 Hinge Bushing Brass ASTM B36
15 Hinge Pin AISI 304 AISI 316
9 Plug Malleable Iron Galvanized
10 Eye Bolt Carbon Steel Zinc Plated or order list.
or order list. DN Dimensions(mm)
DN Dimensions(mm) 2" 50 203 152 120.5 16.5 4-19.1 145
Inch mm L D D1 b n-d H 2.5" 65 216 178 139.5 19 4-19.1 157
2" 50 203 152 120.5 16 4-19.1 146 3" 80 241 191 152.5 19 4-19.1 173
2.5" 65 216 178 139.5 17.5 4-19.1 155 4" 100 292 229 190.5 24 8-19.1 176
3" 80 241 191 152.5 19 4-19.1 173 6" 150 356 279 241.5 25.5 8-22.2 238
4" 100 292 229 190.5 24 8-19.1 180 8" 200 495 343 298.5 28.5 8-22.2 273
5" 125 330 254 216 24 8-22.2 212 10" 250 622 406 362 30.5 12-25.4 329
6" 150 356 279 241.5 25.5 8-22.2 260 12" 300 698 483 432 32 12-25.4 358
8" 200 495 343 298.5 28.5 8-22.2 290 14" 350 787 533 476 35 12-28.5 470
10" 250 622 406 362 30.5 12-25.4 339 16" 400 914 597 540 36.5 16-28.5 535
12" 300 698 483 432 32 12-25.4 376
26 27
AMERICAN VALVES
Grooved Resilient AWWA C508 Rubber Disc

Swing Check Valve (H84X), Swing Check Valve (H44J),
300PSI 300PSI
1 Valve Body ASTM A536,65-45-12 MATERIAL SPECIFICATION
2 Hinge Pin AISI 420 Part No. Part Standard Specication Options
H84X H44J 1 Valve Body ASTM A536,65-45-12
3 Spring AISI 304 AISI 316
Connection Ends: Groove to AWWA C606 4 Eye Bolt Carbon Steel Zinc Plated 2 Bolt Carbon Steel Zinc Plated AISI 304, AISI 316
Working Pressure: 300PSI 5 Disc ASTM A536,65-45-12 AISI 304 3 Washer Carbon Steel Zinc Plated AISI 304, AISI 316
6 Disc Sealing Ring EPDM 200PSI and 250PSI available upon request 4 Disc Carbon Steel+EPDM Carbon Steel+NBR
7 Seat Ring ASTM B62 C83600 (Pressed Fit)
AISI 304, AISI 316 Pressed Fit Temperature Range: 0- 80 5 Bonnet ASTM A536,65-45-12
Coating: Fusion Bonded Epoxy Coating in accordance with or Threaded
Coating: Fusion Bonded Epoxy Coating in accordance with 6 Bonnet Gasket EPDM
ANSI/AWWA C550 or painting upon request 8 Plug Malleable Iron Galvanized Bronze ASTM B584
ANSI/AWWA C550
7 Plug Malleable Iron Galvanized Bronze ASTM B584
10 Plug Malleable Iron Galvanized Bronze ASTM B584 Note: For special material request other than standard specication, please indicate clearly on the inquiry
or order list.
DN Dimensions(mm)
12 Bolt AISI 304 AISI 316 Inch mm L D D1 b n-d
13 Washer AISI 304 AISI 316 2" 50 203 152 120.5 16 4-19.1
14 Nut AISI 304 AISI 316 2.5" 65 216 178 139.5 17.5 4-19.1
3" 80 241 191 152.5 19 4-19.1
4" 100 292 229 190.5 24 8-19.1
or order list.
5" 125 330 254 216 24 8-22.2
DN Dimensions(mm)
6" 150 356 279 241.5 25.5 8-22.2
Inch mm L D1 D2 B C
8" 200 495 343 298.5 28.5 8-22.2
2" 50 171 57.15 60.3 7.93 15.88
10" 250 622 406 362 30.5 12-25.4
2.5" 65 184 69.09 73 7.93 15.88
12" 300 698 483 432 32 12-25.4
3" 80 197 84.94 88.9 7.93 15.88
4" 100 210 110.08 114.3 9.53 15.88
5" 125 248 137.03 141.3 9.53 15.88
6" 150 324 163.96 168.3 9.53 15.88
8" 200 371 214.4 219.1 11.13 19.05
10" 250 457 268.28 273 12.7 19.05
12" 300 535 318.29 323.9 12.7 19.05
28 29
AMERICAN VALVES
MSS SP-126 Silent API 594 Double Door Wafer

Check Valve (HC41X), Check Valve (DH77X),
300PSI 300PSI

Part No. Part Standard Specication Options DH77X Part No. Part Standard Specication Options
HC41X 1 Valve Body ASTM A536,65-45-12
2 Stem AISI 420 AISI 304, AISI 316, AISI 431 Connection Ends: ASME B16.1 AISI 304, AISI 316,
Connection Ends: Flange to ASME B16.1 2 Disc ASTM A536,65-45-12
3 Hinge Bushing ASTM B62 AL-Bronze UNC 95400
Working Pressure: 300PSI 3 Stem AISI 420 AISI 304, AISI 316, AISI 416
4 Spring AISI 304 AISI 316 200PSI and 250PSI available upon request
200PSI and 250PSI available upon request 4 Spring AISI 304 AISI 316
5 Nut AISI 304 AISI 316
Temperature Range: 0- 80 5 Rubber Seat EPDM NBR
Temperature Range: 0- 80 6 Disc ASTM A536,65-45-12 Bronze Plated
Coating: Fusion Bonded Epoxy Coating in accordance with Note: For special material request other than standard specication, please indicate clearly on the inquiry
Coating: Fusion Bonded Epoxy Coating in accordance with 7 O-Ring EPDM NBR
ANSI/AWWA C550 or order list.
ANSI/AWWA C550 or painting upon request 8 Hinge Bushing ASTM B62
9 Seat ASTM A536,65-45-12 Bronze Plated
DN Dimensions(mm)
10 O-Ring NBR EPDM
Inch mm L D D1 D2
11 Screw Carbon Steel Zinc Plated AISI 304, AISI 316
2" 50 54 102 64 46
or order list. 2.5" 65 54 121 78 60
3" 80 57 134 94 70
DN Dimensions(mm) 4" 100 64 162 117 84
Inch mm L D D1 C n-L 5" 125 70 192 145 115
2" 50 120 152 120.5 16 4-19.1 6" 150 76 218 170 134
2.5" 65 135 178 139.5 17.5 4-19.1 8" 200 95 273 224 184
3" 80 155 191 152.5 19 4-19.1 10" 250 108 328 265 220
4" 100 165 229 190.5 24 8-19.1 12" 300 143 408 310 260
5" 125 190 254 216 24 8-22.2 14" 350 184 449 360 302
6" 150 210 279 241.5 25.5 8-22.2 16" 400 191 512 410 350
8" 200 260 343 298.5 28.5 8-22.2
10" 250 285 406 362 30.5 12-25.4
12" 300 315 483 432 32 12-25.4
30 31
AMERICAN VALVES
American Standard Y-Type Strainer

(V4), 300PSI, UL Listed
Y-Type Strainer
Statement:
Installed before relief valves, atmospheric valves, hydraulic control valves as well as
other equipments, strainers serve to filter out the impurities in the flow medium for
protection of valves and equipments in the piping system.
Features:
1. Material: Ductile Iron ASTM A536, 65-45-12
Valve body and cover are produced in ductile iron material which provides guarantee
for high strength and good corrosion resistance.
2. Different Options of Screen Mesh Specication
Different options of screen mesh specification available as per different service
conditions.
3. Fusion Bonded Epoxy Coating MATERIAL SPECIFICATION
V4
Fusion bonded epoxy coating in accordance with ANSI/AWWA C550 for both interior
Ductile Iron Body & Bonnet Part No. Part Standard Specication Options
and exterior surface which provides reliable corrosion resistance.
Stainless Steel Screen 1 Valve Body ASTM A536 65-45-12
AISI 304, AISI 316
Fusion Bonded Epoxy Coating 2 Screen AISI 304 (Perforated)
(Perforated, Knitted, Double Screen)
Gasket: EPDM or Graphite + Acanthopore Plate
Connection Ends: Flange to ASME B16.1 3 Gasket EPDM Graphite + Acanthopore Plate
Working Pressure: 300PSI 4 Bonnet ASTM A536 65-45-12
200PSI and 250PSI available upon request 5 Plug Malleable Iron Galvanized Bronze ASTM B584
Temperature Range: 0- 80 rubber gasket, 6 Bolt Carbon Steel Zinc Plated AISI 304, AISI 316
-10- 350 graphite gasket 7 Flat Washer Carbon Steel Zinc Plated AISI 304, AISI 316
ANSI/AWWA C550 STANDARD SCREEN
DN Hole Dia. Free Flow Area(%)
Sieve No.
Inch mm mm %
2"~2.5" 50~65 25 4 48
3"~4" 80~100 19 5 59
5" 125 14 6 63
V4 V8 6"~12" 150~300 13 6.3 64

Y-Type Strainer Grooved Y-Type Strainer Note: For special material request other than standard specication, please indicate clearly on the inquiry
Page 33 Page 34 or order list.
DN Dimensions(mm)
2" 50 200 152 120.5 16 4-19.1 155
2.5" 65 254 178 139.5 17.5 4-19.1 165
3" 80 257 191 152.5 19 4-19.1 180
4" 100 308 229 190.5 24 8-19.1 229
5" 125 397 254 216 24 8-22.2 285
6" 150 470 279 241.5 25.5 8-22.2 311
8" 200 549 343 298.5 28.5 8-22.2 394
10" 250 654 406 362 30.5 12-25.4 487
12" 300 759 483 432 32 12-25.4 547
32 33
AMERICAN VALVES
Grooved End Y-Type Strainer

Hydraulic Control Valves,
Cap Plug (Brass H62)
(V8), 300PSI
Class 125/150
Up Bonnet (ASTM A536,65-45-12)
Up Gland (ASTM A536,65-45-12)

Statement Diaphragm (EPDM)
Connection Ends: Groove to AWWA C606 The hydraulic control valve was initially originated in Holand, Bottom Gland (ASTM A536,65-45-12)
Bushing (Brass H62)
Israel and Denmark, used for agricultural irrigation. Later the
Working Pressure: 300PSI product was introduced into the United Sates, Canada and Asian Middle Bonnet (ASTM A536,65-45-12)
200PSI and 250PSI available upon request countries. It was from the 1990s when the product first entered
Stem (AISI 304)
Temperature Range: 0- 80 China, and ever since its entrance it gets rapidly developped and
widely applied in different industrie aside from irrigation.
Coating: Fusion Bonded Epoxy Coating in accordance with Bolt (AISI 304)
ANSI/AWWA C550 or painting upon request The hydraulic control valve produced by Jinan Meide is new style Spring ( Stainless Steel 4Cr13)
that absorbed the essence of other well-known brands which Main Disc (ASTM A536,65-45-12)
makes it better in energy saving, consumption reducing and Main Gasket (EPDM)
accurate adjusting achieving. The MECH brand hydraulic control Gland of Main Disc (ASTM A536,65-45-12)
valves have been widely used in China, Europe and South East Seat (AISI 304)
MATERIAL SPECIFICATION Asian countries in pipe system of irrigation, water supplying, re
protection and air conditioning which has medium of water under
Part No. Part Standard Specication Options Valve Body (ASTM A536,65-45-12)
80 or other medium with similar physical and chemical property
as water.
2 Screen AISI 304 AISI 316
3 Rigid Coupling ASTM A536,65-45-12 Specications
4 Cap ASTM A536,65-45-12 Basic Valve: Y-Type Direct-ow
Temperature Range: 0- 80 Water Head Loss (psi)
STANDARD SCREEN
Testing Standard: API 598
DN Hole Dia. Free Flow Area(%)
Sieve No.
Inch mm mm % Flow Diagram of Basic Valve
2"~2.5" 50~65 25 4 48
3"~4" 80~100 18 5 53
5" 125 13 6 58
6"~12" 150~300 12 6.3 56
or order list.
DN Dimensions(mm)
Inch mm L OD d A B DN50
DN65
2" 50 247.5 60.3 57.15 15.88 7.92
Flow Rate (gpm)

2.5" 65 273 73 69.09 15.88 7.92
3" 80 298.5 88.9 84.94 15.88 7.92 DN80
4" 100 362 114.3 110.08 15.88 9.52

DN100
5" 125 419 141.3 137.03 15.88 9.52
6" 150 470 168.3 163.96 15.88 9.52 DN125
8" 200 609.5 219.1 214.4 19.05 11.13 DN150
10" 250 686 273 268.28 19.05 12.7
12" 300 762 323.9 318.29 19.05 12.7 DN200
DN250
Mportant notes: DN300

DN350
1.The products listed in this catalogue are intended to be DN400
assembled only in pipelines of same or lower pressure DN450
DN500
ratings and properly installed. In case of special request, DN600
please contact with factory for support and conrm.
2.It can happen that the catalogue might not be updated
while product design improved. In this case, design of the
product should be as conrmed when order placed.
3.Jinan Meide Casting Co., Ltd. reserves the right for
50 65 100 125 150 250 350 450 500
construe of the information provided in this catalogue DN 80 200 300 400
Kv 41 53 105 175 285 402 730 1160 1400 1770 3010 3225 3395
34 35
AMERICAN VALVES
SK710X Electromagnetic 1. Statement 4. Typical installation illustration

SK710X Electromagnetic Control Valve is a diaphragm type of hydraulic control valve driven by the
Control Valve hydraulic pressure within the piping system. This type of valve is widely applied in the eld of piping system
optimization, pressure division, water reservoir (tank) backup, change of industrial valves, etc., with its
closing and opening remotely controlled by electric signal.
2. Operational principle
SK710X Electromagnetic Control Valve is controlled by solenoid valve and equipped with normally open (or
normally closed) two positions two ways or two positions three ways solenoid pilot valve, needle valve, mini
strainer and ball valve, etc.
When the normally open solenoid valve is applied, the main valve in most cases will be in open position.
When there is pressure coming from the ow direction, Pressure P1 enters the upper cavity room of the
valve through the guide tube and then comes to the low pressure area through the normally open solenoid
valve. In this way the upper cavity room is not able to form conned space and the disc of the main valve
will be opened at the pressure of P1. When the normally open solenoid valve is closed, pressure P1 will
be accumulated inside the upper cavity which will gradually push the membrane to close the disc and the
valve.
For normally closed solenoid valve, the main valve will be in most cases closed and operation principle
same as stated above. The application of the solenoid valve depends on the working environment.
In case the water inside the piping system are highly corrosive or with high deposits, user can choose also
to control the valve with medium from outside. It's up to the option of the client, depending on different
working conditions.
5. Common problems and proposed solutions
3.Property and advantages
Driven by pressure of pipe system, work automatically without any power-generating. It saves installation Common Problems Proposed Solutions
and repairing space. Pressurize in front of the valve but valve can't be opened when Check if needle valve or ball valve in front of the basic valve is
Controlled by solenoid valve, save energy and wiring costs, can be used for large range of pressure and choose condition of normally open and no power. opened. If not, please open it.
voltage.
Check condition of wiring, make sure action in place and for the
Series of mode of execution can be changed to hand control, normally closed solenoid valve control or The basic valve can't be closed when choose normally open and solenoid valve and sealing is good condition for the solenoid valve.
normally open solenoid valve control, etc. shut down the power. Check if there's sundries blocked inside the basic valve. Wash the
mini strainer before basic valve and make sure it's unblocked.
Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure
uctuation, and the diaphragm with support is well protected.
Pressure in front and the valve can't close complete with leakage
Check if any damage or blocks on the sealing surface of basic valve.
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow. when choose condition of normally close and no power.
Long pitch orientation design for stem move, stable and no gap resistance.
No water after valve, valve is not open when choose condition of Check if solenoid valve is in good working condition. Check if needle
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at
normally close and electried. valve or ball valve is open in front of the valve.
against stem, it can balance the tolerance from machining and sealing surface. Good connection without
leakage.
Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology
and strict quality control system, testing reports and testing bars can be supplied with order. Records and
testing bars maintained for one year in the factory.
Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rust-
resisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve.
All the characteristics in accordance with ANSI/AWWA C550 and other international specications like
WRAS, NSF61.
36 37
AMERICAN VALVES
SK720X Pressure 1.Statement 4.Typical installation illustration

SK720X Pressure Reducing Valve is a diaphragm type of hydraulic control valve driven by the hydraulic
Reducing Valve pressure within the piping system. The function of the valve is to reduce the high pressure to the pre-set
low pressure, and despite the uctuation of medium ow or pressure before the valve the pressure after the
valve will always remain stable and maintain the set pressure range.
2.Operational principle
SK720X Pressure Reducing Valve is controlled by pressure reducing pilot valve and equipped with pressure
reducing pilot valve, needle valve, mini strainer and ball valve, etc.
Under normal conditions, water ow comes continuously from the inlet opening to the upper cavity room
(2) of the basic valve through the needle valve (1); When the pressure before the pilot valve (3) is lower
than its pre-set value, the pilot valve will remain at full open position and the upper cavity room of the basic
valve is not able to get accumulating pressure. Under this condition, the disc of the basic valve will be
open at the water pressure from the inlet opening to allow water ow. The pressure reducing pilot valve
closes gradually when the pressure after pilot valve exceeds its pre-set value. Pressure gets accumulated
within the upper cavity room and membrane drives the disc down to close the valve till the pressure after
the pilot valve gradually reduces to its pre-set value. The pilot valve opens again when the pressure after
the valve becomes lower than the pre-set value, and the basic valve will then open with the release of the
accumulated pressure in the upper cavity room.
The throttle orice (5) that connects the lower cavity to the outlet serves to keep the reaction of the valve 5.Basic Parameters 6.Notes for installation and debugging
gentle and stable. The ball valve (4) controls the outlet water ow rate from the upper cavity room and thus
All the Pressure Reducing Valves have been finished initial
to stabilize the action of the basic valve. The ball valve can be adjusted with different working conditions. In Working Pressure
Pressure Symbol Unit debugging tests before delivery. Further dubugging test is also
case of emergency, the ball valve can also be closed manually for cutting off of the basic valve. 175PSI 250PSI 300PSI suggested during using according to different working conditions.
3.Property and advantages Max. Inlet pressure P1max 1.0 1.6 2.5 After the pipe system becomes stable, please loose the adjusting
Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy screw on the top of pilot valve to the top-most position.
Min. Inlet pressure P1min P2max + 0.2
conservation and environment protection. Tighten adjusting screw of pilot valve in clockwise slowly. When
Controlled by the pilot valve, lower energy consumption, achieve accurate pressure reducing results, have Max. Outlet pressure P2max 0.8 1.0 1.6 outlet pressure increase to the set pressure please fasten the
function of stabilizing pressure after the valve. Min. Outlet pressure P2min MPa 0.05 locknut under the adjusting screw.
Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure Characteristics of ow
P2Q 10%
If go beyond the set pressure during adjusting, please repeat the
uctuation, and the diaphragm with support is well protected. deviation above steps. Remember, pressure can be only adjusting from low
Pressure characteristic
Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to deviation
P2p 5% level to high level and pay attention to make the adjusting slowly.
keep stability of pressure after the valve, avoid any vibration and noise. Min. pressure deviation Pmin 0.2
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of
cavitation.
Long pitch orientation design for stem move, stable and no gap resistance. 7.Common problems and proposed solutions
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at
Common Problems Proposed Solutions
leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure.
a.Check if any sundries on the sealing surface of basic valve or pilot valve.
Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology b.Check if any damage on the sealing surface of basic valve or pilot valve.
and strict quality control system, testing reports and testing bars can be supplied with order. Records and Outlet pressure is similar with inlet pressure, no pressure reduction. c.Check if any damage or fatigue on spring of basic valve or pilot valve.
testing bars maintained for one year in the factory. d.Check if any damage or fatigue on diaphragm of basic valve or pilot valve.
e.Check if any corrosion or blocking on stem of basic valve or pilot valve.
resisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. a.Close the needle valve before the basic valve and open 1/4 turns slowly. Open the big hex
All the characteristics in accordance with ANSI/AWWA C550 and other international specications like screw on the top of bonnet, release air. Adjust the needle valve on inlet conduit slowly
Strong vibration and noise.
until no vibration.
WRAS, NSF61.
b.Calculate the ow again and collect proper size of valve or add throttling set.
a.Check if pressure is uctuating strongly at inlet. Try to keep it within small range.
Pressure after the valve is not stable. b.Check if required ow is too different than actual ow, recalculate ow and choose new
valve with proper size.
38 39
AMERICAN VALVES
SK730X Pressure 1.Statement 4.Typical installation illustration

SK730X Pressure Relief & Sustaining Valve is a diaphragm type of hydraulic control valve driven by the
Relief & Sustaining Valve hydraulic pressure within the piping system. One prominent feature of the valve is, it can serve as pressure
relief valve and sustaining valve at the same time. As pressure relief valve, it releases the high pressure
before the valve out of the piping system for protection of the pipes and the equipments when the pressure
exceeds its pre-set value; As pressure sustaining valve, it maintains the water pressure above certain set
value for guarantee of water supply to upstream area
SK730X Pressure Relief & Sustaining Valve is controlled by pressure relief/sustaining pilot valve and
equipped with pressure relief/sustaining pilot valve, needle valve, mini strainer and ball valve, etc.
As Pressure relief valve, the valve is connected with branch pipe and directed to lower pressure area or
drainage ditch. In normal working conditions, water ow enters the upper cavity room (2) through needle
valve (1). When the pressure before the pilot valve (3) is lower than its pre-set value A, the pilot valve will
remain closed and the water that enters the upper cavity room drives the membrane down and closes the
disc and the basic valve. The pilot valve opens when the pressure before the valve exceeds its pre-set For Pressure Relief For Pressure Sustaining
value and the pressure accumulated in the upper cavity room gets released. Under the pressure from the
inlet opening, the disc of the basic valve opens. In this way the pressure within the piping system will be
maintained under the pre-set value A.
As pressure sustaining valve, the valve is connected in series with the main pipe and serves to maintain 5.Basic Parameters 6.Notes for installation and debugging
the pressure before valve above the set value B. Under normal conditions, water ow comes continuously All the Pressure Relief & Sustaining Valves have been nished initial
from the inlet opening to the upper cavity room (2) of the basic valve through the needle valve (1); When debugging tests before delivery and the set-pressure is 0.6MPa.
Working Pressure
the pressure before the pilot valve (3) is lower than its pre-set value, the pilot valve will remain closed and Further debugging test is also suggested during using according to
Pressure Symbol Unit
the water that enters the upper cavity room drives the membrane down and closes the disc and the basic different working conditions.
175PSI 250PSI 300PSI
valve for accumulation of pressure till equals to the set value B. The pilot valve opens when the pressure After the pipe system becomes stable, please loose the lock nut
before the valve exceeds its pre-set value and the pressure accumulated in the upper cavity room gets under adjusting screw, open the ball valve or needle valve (1)
released. Under the pressure from the inlet opening, the disc of the basic valve opens to allow water ow. Set Pressure 0.83 1.33 1.7
slightly, when pressurize, adjust the adjust screw on pressure
In this way the pressure within the piping system will be maintained under the pre-set value B. Ps relief pilot valve and fasten the lock nut when it achieves pressure
Set Pressure Ps0.5: 0.014 MPa;
required. Pay attention that when adjust pressure relief pilot valve,
3.Property and advantages Difference Ps0.5: 3%Ps
clockwise is for increasing pressure and anti-clockwise is for
Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy MPa reducing pressure.
conservation and environment protection. Open/Close
Ps0.3: 0.06MPa;
Pressure Pb
Ps0.3: 20%Ps
Controlled by pilot valve, lower energy consumption, achieve accurate pressure relief and pressure Difference
holding results, reliable and safe.
Discharge
Dual cavity design, with functions of fully opening and fully closing. Slow shut causes no pressure pressure
Pd 1.2Ps
Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to
keep stability of pressure after the valve, avoid any vibration and noise. 7.Common problems and proposed solutions
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of Common Problems Proposed Solutions
cavitation.
a.Check if any sundries on the sealing surface of basic valve or pilot valve.
Long pitch orientation design for stem move, stable and no gap resistance. b.Check if any damage on the sealing surface of basic valve or pilot valve.
The pressure of pipe system is lower than set-pressure, the valve dose not close.
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at c.Check if any damage or fatigue on spring of basic valve or pilot valve.
d.Check if any damage or fatigue on diaphragm of basic valve or pilot valve.
leakage.
a.Check if ball valve (4) is closed, if yes, please open it.
Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology b.Check if any blocks in basic valve or on stem of pilot valve, if yes, please remove the block
and strict quality control system, testing reports and testing bars can be supplied with order. Records and The pressure of pipe system is higher than set-pressure, the valve dose not open.
or change new stem.
testing bars maintained for one year in the factory. c.Check if lock nut and adjust screw were adjusted wrongly, please try to repeat all the actions.
WRAS, NSF61.
40 41
AMERICAN VALVES
SK750X Remote Float 1.Statement 4.Typical installation illustration

SK750X Remote Float Control Valve is a diaphragm type of hydraulic control valve driven by the hydraulic
Control Valve pressure within the piping system, designed with adjustable parallel oat. The valve is capable to maintain
the water surface at set position despite the uctuation of ow rate and widely applied where there is water
reservoir or water box for injection of water.
SK750X Remote Float Control Valve is controlled by angle valve, oat and ball lever, and equipped with
needle valve, mini strainer and ball valve, etc.
Under normal conditions, water ow comes continuously from the inlet opening to the upper cavity room
(2) of the basic valve through the needle valve (1); When the oat is not reaching the set position, the angle
valve 4 remains open. The water that enters the upper cavity room of the basic valve discharges into the
water tank and no accumulation within. Under this condition, the disc of the basic valve remains open at the
water pressure from the inlet opening to allow water supply to the water tank. With the raising of the water
surface, the oat (6) gradually raises and closes the angle valve (4). Pressure gets accumulated within the
upper cavity room and drives the membrane down to close disc and the basic valve gradually. When the
water surface reaches the set position, the angle valve close completely and so with the basic valve and the
water supply stops. When water position declines, the pressure within the upper cavity room gets released
through the angle valve and the basic valve opens to continue with water supply.
Needle valve (1) serves to control the closing speed of the valve to prevent formation of water hammer; In
case the oat is not working, ball valve (3) can close the basic valve for emergency cut-off.
Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy
conservation and environment protection.
Controlled by angle valve and oat, lower energy consumption, achieve accurate level limit, slowly shut
and avoid close valve water hammer.
Separate angle control, including separate angle valve, ball lever and oat, can be installed separately
with basic valve, suitable for limited installation and repairing space, avoid inuence to level measuring by
the wave beside inlet water.
Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to 5.Technical Parameter
keep stability of pressure after the valve, avoid any vibration and noise. Accuracy of Surface Control: 25mm
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of 6.Common problems and proposed solutions
cavitation.
Long pitch orientation design for stem move, stable and no gap resistance. Common Problems Proposed Solutions
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at a.Check if any sundries on the sealing surface of basic valve or pilot valve.
against stem, it can balance the tolerance from machining and sealing surface. Good connection without b.Check if any damage on the sealing surface of basic valve or pilot valve.
c.Check if block on lever of controlling angle valve.
leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Basic valve does not close when water
d.Check if ball lever has been corrosive and oat missing.
meets specified level and continue to
Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology e.Check if any damage for diaphragm.
supply water.
and strict quality control system, testing reports and testing bars can be supplied with order. Records and During the checking, please close ball valve (3), if the basic valve was closed, please just disregard method of a, b and e and only check
sealing surface of angle valve and ball lever. If the basic valve does not close when close ball valve (3), please cut off the water supply and
testing bars maintained for one year in the factory. check sealing surface of basic valve, diaphragm and stem. If any damaged parts, please change new one.
resisting material, fusion bonded epoxy coating both for interior and exterior surface of the basic valve. Level adjusting is not accurate and oat
a.Check if the oat was installed close to water outlet. If yes, please move it to far away from the water outlet. Or you can use barrel to avoid
All the characteristics in accordance with ANSI/AWWA C550 and other international specications like the affection of the wave.
jumps strongly.
b.Check the location of oat and make sure the top-most position which oat can catch is the set-level of the water box.
WRAS, NSF61.
To make sure water won't exceed set-level double insurances is recommended. That's to assemble two position two-way solenoid valve
Reasonable suggestion
before the controlling angle valve to make sure that the valve can be closed in case of emergency.
42 43
AMERICAN VALVES
1.Statement 4.Typical installation illustration

SK760X Slow Shut SK760X Slow Shut Control Valve (Pump Control Valve) is a diaphragm type of hydraulic control valve
driven by the hydraulic pressure within the piping system, widely applied in the pump outlet for prevention
Control Valve of medium back-ow, pressure uctuation and water hammer formation. Under normal working conditions,
pressure before the valve is higher than pressure after, and the valve remains fully open. When pressure
(Pump Control Valve) after valve exceeds pressure before valve, the valve is capable to be closed rapidly to prevent backow of
water and protect the pump and piping system. The design of the valve incorporates the function of slow-
opening, quick closing, slow closing and water hammer absorption, no large pressure uctuation within the
system.
SK760X Slow Shut Control Valve (Pump Control Valve) is composed of needle valve (or ball valve), mini
strainer and ball valve, etc.
Before the pump starts, there is no pressure before the valve, and disc (5) is closed under the pressure
from the spring. With the start of the pump, the pressure before the valve increases gradually. At the same
time, the pressure water enters the lower cavity room (2) through the needle valve (1) (or ball valve). The
two combined force opens the disc of the basic valve rapidly to allow water supply. When the pump stops
(as planned or out of accident), pressure before the valve suddenly declines. Pressure after valve exceeds
that before the valve. As a result, the higher pressure ows back to the upper cavity room through the
needle valve (4) (or ball valve) and gets accumulated to drive the membrane down to close the valve disc
(5). The pressure within the lower cavity room (2) discharges to the lower pressure area before the basic
valve through needle valve (1) (or ball valve) , which slows down the closing process to prevent formation
of water hammer.
The opening and closing speed of the valve can be controlled by adjustment of the needle valve (1) & (4) (or
ball valve). The valve is designed with dual disc, especially good for working in complicated piping system
and working conditions where there is tremendous pressure and water back-ow.
3.Property and advantages 5.Technical Parameter

Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy Working Pressure
conservation and environment protection. Pressure Symbol Unit
175PSI 250PSI 300PSI
uctuation, and the diaphragm with support is well protected. Min Closing Pressure Pg MPa 0.05
Stable when open and close, the speed of opening and closing can be adjusted according to working Slow-shut Time t s 260
conditions to avoid pressure uctuation and water hammer. It can achieve real silence. Note: Slow-shut time can be adjusted as per request
Dual disc, customer can choose design of main disc + second disc. Main disc will fall freely with its weight
when pump stop working, then 90% of inlet of basic valve will be will closed, the water will not cause 6.Common problems and proposed solutions
pump reversing. The second disc will close the 10% left slowly by the pressure of controlling cavity then
huge energy of water hammer will be eliminated. Common Problems Proposed Solutions
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of a.Check if there's gas in the upper cavity room. Loose the hex brass nut on the top of bonnet to
Strong vibration and noise when start-up discharge gas.
cavitation. the pump. b.Adjust the needle valve or ball valve (1) at inlet to proper opening speed.
Long pitch orientation design for stem move, stable and no gap resistance. c.Recalculate the ow and choose new valve with proper size or add throttling set.
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at Strong vibration and noise when stop a.Adjust needle valve or ball valve (4) to proper closing speed.
against stem, it can balance the tolerance from machining and sealing surface. Good connection without the pump. b.Consider to choose design of dual discs.
leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure.
Ductile iron castings with nodularity higher than 90%, foundry in house with advanced melting technology a.Check if there's sundries on the sealing surface of main disc or second disc.
and strict quality control system, testing reports and testing bars can be supplied with order. Records and b.Check if damage on sealing surface of main disc or second disc.
Valve does not work and cause pump's
c.Check if stem corroded or blocked.
testing bars maintained for one year in the factory. reversing.
d.Check if damage on diaphragm.
Good corrosion resistance, with stainless steel, copper alloy, rubber made from DuPont and other rust- If any damaged parts found, please change new one.
WRAS, NSF61.
44 45
AMERICAN VALVES
SK780X Pressure Differential 1.Statement 4.Typical installation illustration

SK780X Pressure Differential By-pass Balancing Valve is a diaphragm type of hydraulic control valve driven
By-pass Balancing Valve by the hydraulic pressure within the piping system, widely applied in HVAC system for guarantee of ow
stability in the air conditioning, refrigeration and heating system and pump working. The valve prevents the
effect on the other pipe branches when there is uctuation on one branch by balancing of pressure in the
radiant and distribution water manifold, thus to protect the efcient and safe working of the refrigeration set
or heating set.
SK780X Pressure Differential By-pass Balancing Valve is composed of pressure balancing pilot valve,
needle valve (or ball valve), mini strainer and ball valve, etc.
SK780X Pressure Differential By-pass Balancing Valve is installed between radiant and distribution water
manifold (water supply and water return). Water ow enters continuously from water supply duct to the
valve inlet and then to the upper cavity room (2) through needle valve (1) (or ball valve). Pilot valve (3) is
connected to the water supply duct and return duct by guide tube (4) and (5) to sensing of the pressure
difference and adjustment of the opening position of the pilot valve accordingly. When the pressure
difference is large, pilot valve opens broadly, the pressure inside upper cavity room (2) declines and the
basic valve opens broadly. As result the water ow between the supply and return duct increase and the
entire system gets balanced. When the pressure difference is small, pilot valve (3) turns to close at the
pressure of the spring, the pressure inside upper cavity room (2) increase and the basic valve turns to
close. As result the water ow between the supply and return duct decreases and the entire system also
gets balanced.
Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy
conservation and environment protection.
Antenna type of conduit, See No.4 and 5 conduit, connect with water knockout drum and water collector
(supplying pipe and return pipe), can achieve accurate and reliable adjusting.
Have internal orice, connect bottom cavity and outlet of the basic valve, make sure stability of reaction to 5.Notes for installation and debugging
keep stability of pressure after the valve, avoid any vibration and noise. The valve has been finished initial debugging tests before delivery. Further
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of debugging test is also suggested during using according to different set-conditions.
cavitation. Over review pressure meter of water knockout drum and water collector, adjust pilot
Long pitch orientation design for stem move, stable and no gap resistance. valve (3) according to set-difference of pressure. Clockwise is for increasing the
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at pressure difference and anti-clockwise is for reducing pressure difference when set
against stem, it can balance the tolerance from machining and sealing surface. Good connection without adjusting screw on the top of pilot valve. When adjusting is done, fasten the lock nut.
leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. Then you'll got set-difference for the pressure no matter how the pressure of pipe
system changes.
and strict quality control system, testing reports and testing bars can be supplied with order. Records and Adjust needle valve (ball valve) can achieve different movement speed for the
testing bars maintained for one year in the factory. basic valve. Normally, it has been adjusted well before delivery. No further adjusting
suggested if no special notice.
All the characteristics in accordance with ANSI/AWWA C550 and other international specications like 6.Common problems and proposed solutions
WRAS, NSF61. Common Problems Proposed Solutions
a.Check if any sundries on the sealing surface of
basic valve or pilot valve.
Pressure difference is smaller
b.Check if any damage on the sealing surface of
than set-value and does not
basic valve or pilot valve.
reach the set-difference.
c.Check if needle valve (ball valve) (1) was closed
or almost closed. If yes, please open it.
Pressure difference is bigger a.Check if ball valve (6) at outlet was closed. If yes,
than set-value and does not please open it.
reach the set-difference. b.Check if there's any block for pilot valve.
46 47
AMERICAN VALVES
SK790X Deluge 1.Statement 4.Typical installation illustration

SK790X Deluge Alarm Valve is a diaphragm type of hydraulic control valve driven by the hydraulic pressure
Alarm Valve within the piping system, functioning as ow control and alarming device in the sprinkler and pre-action
system, i.e. to start the sprinkler system for quenching of the re and send out re alarm through the re
bell when there is re detected.
SK790X Deluge Alarm Valve is equipped with solenoid, anti-reset controller, mini strainer, ball valve and
pressure gauge, etc..
For deluge valve there is set condition and work condition. When the valve is under set condition, ball
valve (3) is open, ball valve (7), solenoid (8) and remote ball valve (9) are closed, the anti-reset controller
is connected, and pressure gauge (1) and pressure gauge (6) shows the same value. When ball valve (11)
is open, pressure gauge (10) shows 0. When ball valve (12) and (14) are open, (13) & (15) closed, there is
no hydraulic pressure for pressure switch (17) , and alarm (18) does not work. Under set condition, you can
operate as following if you want to test the pressure switch alarm device (17) and water motor alarm (18):
close ball valve (14) and open (15), and then close (15) and open (14) after testing.
In case there is fire detected, the following 3 methods will set the deluge valve into work condition
5.Notes for installation and debugging
immediately, A: Opening solenoid valve (8) B: Opening ball valve (7) C: Opening remote ball valve (9). Any
of the above 3 methods can get the pressure within the control room of the basic valve released rapidly to Please check if pressure switch and alarm bell are in good condition before
open the valve and set it into working condition. At this time the sealing ball of anti-reset controller makes installation. Make sure water can not leak to system from water supplying
controller in a shutdown state, water will pass through the main valve, ball valve (12), (4), pressure switch system or there's equipment to discharge the leaked water.
(17), re bell (18), the pressure switch bell sends out signal alarms. After re ghting, close ball valve (7), Please adjust all the ball valves to make sure the basic valve be in set
solenoid valve (8), remote valve (9), press the anti-reset controller handle till the pressure gauge (6) and condition.
pressure gauge (1) shows the same value. The deluge alarm valves returns to set condition. Make sure anti-reset controller is in good condition and seal well before
Ball valve (2), (5) & (11) are normally open unless need to change the pressure gauge. installation. If there's water with pressure in front of the valve, please closed
ball valve (7), (9) and electromagnetic valve when it's in empty state behind
3.Property and advantages the basic valve, press the anti-reset controller, when up cavity of basic valve
Driven by pressure of pipe system, work automatically with energy of pipe system to achieve energy is full of water please check if there's any leakage behind the valve. If no
conservation and environment protection. leakage, it said anti-reset controller is in good condition.
uctuation, and the diaphragm with support is well protected. 6.Common problems and proposed solutions
Triple insurance, there're three opening types used for different situation of ring. Anyone can make the Common Problems Proposed Solutions
valve into working condition.
a.Check if any sundries or damage on the sealing
Anti-reset controller, hydraulic pressure type, compact design, tight sealing, operating by hand to make Press anti-reset controller surface of basic valve or anti-reset controller.
sure all the parts including basic valve, ball valves and conduits are all in good condition after out-re. after fire-out, there's still b.Check if any damage on diaphragm.
water coming out behind the c.Check if controlling valve (7), (8) and (9) were
Channel with straight-ow, slight friction loss, no eddy ow and turbulent ow, cut down the damage of valve. closed completely. Close them or replace with
cavitation. new ones.
Long pitch orientation design for stem move, stable and no gap resistance.
Balanced automatically, big gap design on connection of disc and stem, disc is free on the vertical at When open controlling valve a.Check if controlling valve (7), (8) and (9) were
(7), (8) and (9) no water opened. Close them or replace with new ones.
against stem, it can balance the tolerance from machining and sealing surface. Good connection without comes out from the basic b.Check if there's block on stem of basic valve,
leakage. Achieve functions of both reducing dynamic pressure and reducing static pressure. valve. repair it.
and strict quality control system, testing reports and testing bars can be supplied with order. Records and
testing bars maintained for one year in the factory.
WRAS, NSF61.
48 49
AMERICAN VALVES
Ordering Guide of Hydraulic Control Valve Roll Groove Dimensions

Piping system (two words) Size in mm (three digitals) Main property(three digitals) Other property(two digitals) Material
of basic valve (one letter) Material of pilot valve (one letter) Pressure in bars (two digitals)
Basic valve (Dual-chamber diaphragm) SK700X No other special requirements 00 Ductile Iron Q
Water supply piping system: WW
Basic valve (Single-chamber diaphragm) SK400X Special closing and opening speed 03 Carbon Steel C
Drinking water piping system: WD
Basic valve (Piston type) SK800X Non-retuning 06 Stainless Steel P
Aggressive water piping system: WA
Electromagnetic control valve SK710X With high sensitive pilot valve 09
Air conditioning water piping system: WC
Pressure reducing valve SK720X With electromagnetic valve 12
Heating piping system: WH
Pressure relief & sustaining valve SK730X With electromagnetic valve and non-return 15
Al-bronze T
Remote oat control valve SK750X With overpressure protection pilot valve 18
Stainless steel P Roll Grooving Machine

Slow shut control valve With dual-disc 21
050 (Pump control valve) SK760X Cracking pressure lower than 0.05MPa 24
Pipe OD
065 Pressure differential by-pass balancing valve With throttle opening 27 Nominal Gasket seat Groove Dia C Min.
10 Groove Width B Groove Depth MaxAllow Flare
080 SK780X With indication of position 30 Size A Allow wall
16 Basic Tolerence 0.76/0.03 Basic Tolerence D(ref) Dia F
... With exhaust unit 33 mm/in 0.76/0.03 thickness T
Deluge alarm valve SK790X 25 mm/in mm/in mm/in mm/in mm/in mm/in mm/in
mm/in mm/in
700 With Double liquid level control 36
With ushing function in up chamber 39 25 33.7 +0.41 -0.68 15.88 7.14 30.23 -0.38 1.60 34.5 1.8
Other special requirement 99 1 1.327 +0.016 -0.026 0.625 0.281 1.190 -0.015 0.063 1.358 0.071
32 42.4 +0.50 -0.60 15.88 7.14 38.99 -0.38 1.60 43.3 1.8
Examples: 1 1.669 +0.020 -0.023 0.625 0.281 1.535 -0.015 0.063 1.705 0.071
DN80, PN16, Dual-chamber diaphragm type remote oat control valve for water supply piping system, with electromagnetic valve controlling, Ductile iron basic valve 40 48.3 +0.44 -0.52 15.88 7.14 45.09 -0.38 1.60 49.4 1.8
body, brass pilot valve: WW-080-SK750X-12-QT-16 1 1.900 +0.017 -0.020 0.625 0.281 1.779 -0.015 0.063 1.945 0.071
DN200, PN10, Dual-Chamber diaphragm type slow control valve for drinking water piping system, specially used for the pool water (under 0.05MPa), Stainless steel 50 60.3 +0.61 -0.61 15.88 8.74 57.15 -0.38 1.60 62.2 1.8
basic valve body, Stainless steel pilot valve: WD-200-SK760X-24-PP-10 2 2.375 +0.024 -0.024 0.625 0.344 2.250 -0.015 0.063 2.449 0.071
65 73.0 +0.74 -0.74 15.88 8.74 69.09 -0.46 1.98 75.2 2.3
2 2.875 +0.029 -0.029 0.625 0.344 2.720 -0.018 0.078 2.961 0.091
65 76.1 +0.76 -0.76 15.88 8.74 72.26 -0.46 1.99 77.7 2.3
Notes for Installation of Hydraulic Control Valve 2 3.000 +0.030 -0.030 0.625 0.344 2.845 -0.018 0.078 3.059 0.091
80 88.9 +0.89 -0.79 15.88 8.74 84.94 -0.46 1.98 90.6 2.3
Check the uniformity of name plate, quality guarantee card and marking on valve products. 3 3.500 +0.035 -0.031 0.625 0.344 3.344 -0.018 0.078 3.567 0.091
Clean the pipes and make sure no rocks, welding slags and other sundries. 100 108.0 +1.07 -0.79 15.88 8.74 103.73 -0.51 2.11 109.7 2.3
Horizontal installation is the best choice, and other installing direction can also be chosen and 4 4.250 +0.042 -0.031 0.625 0.344 4.084 -0.020 0.083 4.319 0.091
work properly. 100 114.3 +1.14 -0.79 15.88 8.74 110.08 -0.51 2.11 116.2 2.3
Strainer is suggested to be installed before the basic valve, besides, maintenance gate valves 4 4.500 +0.045 -0.031 0.625 0.344 4.334 -0.020 0.083 4.575 0.091
were also suggested to be installed before and after the basic valve. 125 133.0 +1.32 -0.79 15.88 8.74 129.13 -0.51 2.11 134.9 2.9
5 5.250 +0.052 -0.031 0.625 0.344 5.084 -0.020 0.083 5.311 0.114
Make sure the direction of ow is same as arrow on basic valve.
125 139.7 +1.40 -0.79 15.88 8.74 135.48 -0.51 2.11 141.7 2.9
The protection plugs on the both ends are suggested to be removed just before installation to 5 5.500 +0.055 -0.031 0.625 0.344 5.334 -0.020 0.083 5.579 0.114
avoid sundries coming inside.
125 141.3 +1.42 -0.79 15.88 8.74 137.03 -0.56 2.13 143.5 2.9
Check the connection of conduits to make sure no broken, damage and loosing after installation. 5 5.563 +0.056 -0.031 0.625 0.344 5.395 -0.022 0.084 5.650 0.114
Check the repairing ball valve to make sure they're open after installation. 150 159.0 +1.60 -0.79 15.88 8.74 154.50 -0.56 2.16 161.0 2.9
6 6.250 +0.063 -0.031 0.625 0.344 6.083 -0.022 0.085 6.339 0.114
150 165.1 +1.60 -0.79 15.88 8.74 160.8 -0.56 2.16 167.1 2.9
6 6.500 +0.063 -0.031 0.625 0.344 6.330 -0.022 0.085 6.579 0.114
150 168.3 +1.60 -0.79 15.88 8.74 163.96 -0.56 2.16 170.7 2.9
For English Speaking Service 6 6.625 +0.063 -0.031 0.625 0.344 6.455 -0.022 0.085 6.720 0.114
200A 216.3 +1.60 -0.79 19.05 11.91 211.60 -0.64 2.35 219.8 2.9
R&D Center: Sales Department: Exporting Sales Department: Ms. Sunny Guo 8 8.516 +0.063 -0.031 0.750 0.469 8.331 -0.025 0.093 8.653 0.114
Chief Engineer: Ms. Xiaobei Huang Exporting Sales Department: Ms. Zhaoxia Su Tel: 0086-531-87885036 200 219.1 +1.60 -0.79 19.05 11.91 214.40 -0.64 2.34 221.5 2.9
8 8.625 +0.063 -0.031 0.750 0.469 8.441 -0.025 0.092 8.720 0.114
Tel: 0086-531-87746667 Tel: 0086-531-87879384 Fax: 0086-531-87879387
250A 267.4 +1.60 -0.79 19.05 11.91 262.60 -0.69 2.40 270.9 3.6
E-mail: [email protected] Fax: 0086-531-87879387 E-mail: [email protected] 10 10.528 +0.063 -0.031 0.750 0.469 10.339 -0.027 0.095 10.665 0.142
E-mail: [email protected] 250 273.0 +1.60 -0.79 19.05 11.91 268.28 -0.69 2.39 275.4 3.6
10 10.750 +0.063 -0.031 0.750 0.469 10.562 -0.027 0.094 10.842 0.142
300A 318.5 +1.60 -0.79 19.05 11.91 312.90 -0.76 2.77 322.0 4.0
12 12.539 +0.063 -0.031 0.750 0.469 12.319 -0.030 0.109 12.677 0.158
300 323.9 +1.60 -0.79 19.05 11.91 318.29 -0.76 2.77 326.2 4.0
12 12.750 +0.063 -0.031 0.750 0.469 12.531 -0.030 0.109 12.842 0.158
350 377.0 +1.60 -0.79 23.83 11.91 371.44 -0.76 2.77 379.5 4.5
14 14.842 +0.063 -0.031 0.938 0.469 14.623 -0.030 0.109 14.941 0.177
400 426.0 +1.60 -0.79 23.83 11.91 420.46 -0.76 2.77 428.5 4.5
16 16.772 +0.063 -0.031 0.938 0.469 16.553 -0.030 0.109 16.870 0.177
500 529.0 +1.60 -0.79 25.40 11.91 523.46 -0.76 2.77 533.0 5.0
20 20.827 +0.063 -0.031 1.000 0.469 20.608 -0.030 0.109 20.984 0.197
50 51
AMERICAN VALVES
Class 125 Flange and Bolting Dimensions Class 125 Flange and Bolting Dimensions
Flanges Hub Bolt Holes Bolting [NOTE (6)] Flanges Hub Blind Flanges Bolt Holes Bolting
Length
NPS Thickness, Diameter Thickness of Hub Diameter Length
Diameter Length, Diameter of Diameter Diameter Wall Diameter Length
Diameter, Min.,Q of Bolt Nubmer Length NPS Diameter of Flange, Diameter and Diameter of Bolt of Bolt
Min., Min., Bolt Holes of Bolts of Port, thickness, Number of Bolts of Bolts
O [Notes(1) Circle of Bolts of Bolts of Flange, Min., Min., Threads, of Bolt Holes Stud With
X Y [Notes(3)-(5)] [Note(3)] I V of Bolts [Notes(7) [Notes(7)
and(2)] [note(3)] O Q X Min., Circle [Notes(5) Two Nuts
[Note(3)] [Note(4)] anf(8)] and(8)]
[Note(1)] Y and(6)] [Note(7)]
4 230 19.0 135 33 191 3/4 8 5/8 64 [Note(2)]
5 255 19.0 164 37 216 3/4 8 5/8 64 1 110 11.1 49 18 25 9.6 79 5/8 4 1/2 45
6 280 19.0 192 40 241 3/4 8 5/8 64 11/4 115 12.7 59 21 32 11.1 89 5/8 4 1/2 51
8 345 19.0 246 45 299 3/4 8 5/8 64 11/2 125 14.3 65 22 38 12.7 98 5/8 4 1/2 51
10 405 22.2 303 49 368 3/4 12 5/8 70 2 150 15.9 78 25 51 14.3 121 3/4 4 5/8 57
12 485 25.4 357 56 432 3/4 12 5/8 76 21/2 180 17.5 91 29 64 15.9 140 3/4 4 5/8 64
14 535 28.6 391 57 476 7/8 12 3/4 89 3 190 19.0 108 30 76 17.5 152 3/4 4 5/8 64
16 595 28.6 445 64 540 7/8 16 3/4 89 31/2 215 20.6 122 32 89 19.0 178 3/4 8 5/8 70
18 635 31.8 498 68 578 7/8 16 3/4 95 4 230 23.8 135 33 102 22.2 191 3/4 8 5/8 76
20 700 31.8 552 78 635 7/8 20 3/4 95 5 255 23.8 164 37 127 22.2 216 7/8 8 3/4 76
24 815 34.9 560 83 749 7/8 20 3/4 102 6 280 25.4 192 40 152 23.8 241 7/8 8 3/4 83
30 985 38.1 914 1 28 7/8 114 8 345 28.6 246 45 203 27.0 299 7/8 8 3/4 89
36 1170 41.3 1085 1 32 7/8 121 10 405 30.2 303 49 254 28.6 362 1 12 7/8 95
42 1345 44.5 1257 1 1/8 36 1 133 12 485 31.8 357 56 305 20.6 432 1 12 7/8 95
48 1510 50.8 1422 1 1/8 44 1 146 14 535 32.4 391 57 356 22.2 476 1 1/8 12 1 108
54 1685 57.2 1594 1 1/8 44 1 159 16 595 36.5 445 64 406 25.4 540 1 1/8 16 1 114
60 1855 57.2 1759 1 1/4 52 1 1/8 159 18 635 39.7 499 68 457 27.0 578 1 1/4 16 1 1/8 121
72 2195 63.5 2095 1 1/4 60 1 1/8 172 20 700 42.9 553 73 508 28.6 635 1 1/4 20 1 1/8 127
84 2535 69.9 2425 1 3/8 64 1 1/4 191 24 815 47.6 660 83 610 31.8 749 1 3/8 20 1 1/4 140
96 2875 76.2 2756 1 3/8 68 1 1/4 203 30 985 54.0 762 36.6 914 1 3/8 28 1 1/4 159
36 1170 60.3 914 41.3 1086 1 5/8 32 1 1/2 178 222
General note: Dimensions are in millimeters 42 1345 66.7 1066 46.0 1257 1 5/8 36 1 1/2 191 235
Notes: 48 1510 69.9 1219 50.8 1422 1 5/8 44 1 1/2 197 242
(1) For facing, see para.7.2(a). 54(9) 1685 76.2 1594 2 44 1 3/8 216 267
60(9) 1855 79.4 1759 2 52 1 3/8 222 273
(2) Threaded companion anges should not be thinner than the Class 125 thickness on NPS 24 and smaller.
Other types of angs may have thickenesses as given above. 72(9) 2195 88.9 2096 2 60 1 3/8 241 292
84(9) 2535 98.4 2426 2 1/4 64 2 267 324
(3) The ange diameter, bolt circle, and number of bolts are the same in Class 25 as in Class 125.
96(9) 2875 108.0 2756 2 1/2 68 2 1/4 292 356
Bolt hole diameters of Class 25 shall not be modied when mated with Class 125 anges or with steel anges.
General Note: Dimensions are in millimeters.
(4) For spot facing, see para 7.7.
Notes:
(5) For ange bolt holes, see para.7.6. (1) For facing see para.7.2.(a)
(6) For bolts and nuts, see para.8.1. (2) For thread of threaded anges, see paras.7.5.1 and 7.5.2.
(3) All blind ange NPS 12 and larger must be dished with inside radius equal to the port diameter.
(4) For wall thickness tolerance, see para.7.1.
(5) For ange bolt holes, see para.7.6.
(6) For spot facing, see para.7.7.
(7) For bolts and nuts, see para.8.1.1.
(8) Bolt lengths to be compensated for when bolting steel to gray iron anges.
(9) NPS 54 through 96 are included for convenience. Pressure-temperature ratings are the user's responsibility.
52 53
Note:
54

ANSI Valves

Uploaded by

Copyright:

Available Formats

ANSI Valves

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

ANSI Valves

Uploaded by

Copyright:

Available Formats

What is the company history of the business?

What is the company history of the business?

What are the main features and specifications of American Valves gate valves?

What are the main features and specifications of American Valves gate valves?

COMPANY HISTORY

1964 Self Export, Developped US

AWWA C515 Flanged Resilient OS&Y

Working Pressure: 300PSI 8 Stem Bushing Brass Hpb59-1

CLX XZA SMC

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

AWWA C515 Mechanical Resilient NRS Vertical Indicator Post (IP)

MSS SP-67 Resilient Centerline MSS SP-67 Wafer Buttery Valve

Buttery Valve (D71X4, D371X4, XD371X4),

MSS SP-67 Lugged Wafer API 609 Flanged Buttery Valve

MSS SP-67 Grooved Buttery Valve Buttery Valve Performance Data

Part No. Part Standard Specication Options

1 Valve Body ASTM -A536,65-45-12

2 Disc ASTM A536,65-45-12+EPDM or NBR

3 O-Ring NBR EPDM

AWWA Check Valve AWWA C508 Swing Check Valve

Grooved Resilient AWWA C508 Rubber Disc

Part No. Part Standard Specication Options

1 Valve Body ASTM A536,65-45-12 MATERIAL SPECIFICATION

MSS SP-126 Silent API 594 Double Door Wafer

MATERIAL SPECIFICATION MATERIAL SPECIFICATION

American Standard Y-Type Strainer

V4 V8 6"~12" 150~300 13 6.3 64

Grooved End Y-Type Strainer

Up Gland (ASTM A536,65-45-12)

Flow Rate (gpm)

4" 100 362 114.3 110.08 15.88 9.52

Mportant notes: DN300

SK710X Electromagnetic 1. Statement 4. Typical installation illustration

SK720X Pressure 1.Statement 4.Typical installation illustration

SK730X Pressure 1.Statement 4.Typical installation illustration

SK750X Remote Float 1.Statement 4.Typical installation illustration

1.Statement 4.Typical installation illustration

3.Property and advantages 5.Technical Parameter

SK780X Pressure Differential 1.Statement 4.Typical installation illustration

SK790X Deluge 1.Statement 4.Typical installation illustration

Ordering Guide of Hydraulic Control Valve Roll Groove Dimensions

You might also like