F2ce9687a B C

CURSOR TIER 3
SERIES
Industrial application
C87
C87 ENT X - CURSOR 87 TE X
Technical and Repair manual

This publication provides unit and relevant component repair
data, specifications, instructions and methodologies.
This publication has been drawn up for qualified and

specialised personnel.
Before performing any operation check that the part relevant

to the unit on which you must work is available along with all
safety devices for accident-prevention, such as, goggles,
helmet, gloves, shoes, etc. and hoisting and transporting
equipment.
Operations are to be performed by following the indications

included here, using the special equipment indicated and
assuring proper repair, compliance with schedule and
operators safety requirements.
Each repair must aim to restore operating efficiency and safety

in compliance with the FPT provisions.
FPT cannot be held liable for modifications, alterations or other

interventions non authorised by FPT on the vehicle and if the
unit is warranted the above mentioned interventions will cause
its expiration.
FPT is not liable for repairing interventions.
FPT will provide further details required to carry out the

interventions and all the instructions that are not included on
this publication.
Data included in this publication may not be up-to-date

therefore subject to Manufacturers modifications that can be
added at any time for technical or commercial purposes and
also to meet new law regulations in other Countries.
If issues on this publication differ from what is actually noticed

on the unit, please get in touch with the FPT network before
starting any intervention.
It is forbidden to copy this text or any of its parts and all

illustrations included.
Produced by:
Publication edited by
FIAT Powerrtrain Technologies
Mkt. Advertising & Promotion
Viale dellIndustria, 15/17 B.U. TECHNICAL PUBLISHING
20010 Pregnana Milanese Iveco Technical Publications
Milano (Italy) Lungo Stura Lazio, 15/19
Print P2D32C006E - 3rd Ed. 05.2010 10156 Turin - Italy
F2C CURSOR ENGINES 1
F2C CURSOR ENGINES
Cursor F2C Part 1
Cursor engines application G-Drive Part 2
Print P2D32C006E Base - May 2010

2 F2C CURSOR ENGINES
Base - May 2010 Print P2D32C006E

F2C CURSOR ENGINES INTRODUCTION 1
Introduction
Page
PREFACE TO USERS GUIDELINE MANUAL . . 3
SYMBOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Service operations . . . . . . . . . . . . . . . . . . . . . . 3
GENERAL WARNINGS . . . . . . . . . . . . . . . . . . . 5
GENERAL WARNINGS
ON THE ELECTRIC SYSTEM . . . . . . . . . . . . . 7
- Bonding and screening . . . . . . . . . . . . . . . . . . . 8
CONVERSIONS BETWEEN THE MAIN UNITS

OF MEASUREMENT OF THE INTERNATIONAL
SYSTEM AND MOST USED DERIVED
QUANTITIES . . . . . . . . . . . . . . . . . . . . . . . . . 9
KEY OF LECTURE OF THE HEADINGS

AND FOOTNOTES . . . . . . . . . . . . . . . . . . . 10

2 INTRODUCTION F2C CURSOR ENGINES

PREFACE TO USERS GUIDELINE MANUAL

Manuals for repairs are split into Parts and Sections, each one of which is marked by a numeral; the contents of these sections
are indicated in the general table of contents.
The sections dealing with things mechanic introduce the specifications, tightening torque values, tool lists, assembly
detaching/reattaching operations, bench overhauling operations, diagnosis procedures and maintenance schedules.
The sections (or parts) of the electric/electronic system include the descriptions of the electric network and the assemblys
electronic systems, wiring diagrams, electric features of components, component coding and the diagnosis procedures for the
control units peculiar to the electric system.
Section 1 describes the engine illustrating its features and working in general.
Section 2 describes the type of fuel feed.
Section 3 relates to the specific duty and is divided in four separate parts:
1. Mechanical part, related to the engine overhaul, limited to those components with different characteristics based on the
relating specific duty.
2. Electrical part, concerning wiring harness, electrical and electronic equipment with different characteristics based on the relating
specific duty.
3. Maintenance planning and specific overhaul.
4. Troubleshooting part dedicated to the operators who, being entitled to provide technical assistance, shall have simple and
direct instructions to identify the cause of the major inconveniences.
Sections 4 and 5 illustrate the overhaul operations of the engine overhaul on stand and the necessary equipment to execute
such operations.
The appendix contains a list of the general safety regulations to be respected by all installation and maintenance engineers in
order to prevent serious accidents taking place.
The manual uses proper symbols in its descriptions; the purpose of these symbols is to classify contained information. In particular,
there have been defined a set of symbols to classify warnings and a set for assistance operations.
SYMBOLS - Warnings
Danger for persons

Missing or incomplete observance of these prescriptions can cause serious danger for persons safety.
Danger of serious damage for the assembly

Failure to comply, both fully or in part, with such prescriptions will involve serious damage to the assembly and may
sometimes cause the warranty to become null and void.
General danger
! It includes the dangers of above described signals.
Environment protection
Moreover, it describes the correct actions to be taken to ensure that the assembly is used in such a way so as to protect
the environment as much as possible.
NOTE It indicates an additional explanation for a piece of information.

Service operations
Example
1 1 = housing for connecting rod small end bush

Tighten to torque
Tighten to torque + angular value

2 2 = housing for connecting rod bearings

Removal
Intake
Disconnection
Refitting
Exhaust
Connection
Removal
Operation
Disassembly
Fitting in place
Assembly Compression ratio
Tolerance
Tighten to torque
Weight difference
Tighten to torque + angle value Rolling torque

Press or caulk Rotation
Regulation Angle
Adjustment Angular value
Warning
! Preload
Note
Visual inspection
Number of revolutions
Fitting position check
Measurement
Value to find Temperature
Check
Equipment Pressure
bar
Oversized
Surface for machining
Higher than.
Machine finish
Maximum, peak
Undersized
Interference
Less than.
Strained assembly
Minimum
Selection
Thickness
Classes
Clearance
Oversizing
Lubrication Temperature < 0 C
Damp Cold
Grease Winter
Temperature > 0 C
Sealant
Hot
Adhesive
Summer
Air bleeding

GENERAL WARNINGS
Warnings shown cannot be representative of all danger situations possibly occurring. Therefore, it is suggested to
! contact immediate superiors where a danger situation occurs which is not described.
Use both specific and general-purpose toolings according to the prescriptions contained in respective use and
maintenance handbooks. Check use state and suitability of tools not subjected to regular check.
The manual handling of loads must be assessed in advance because it also depends, besides weight, on its size and
on the path.
Handling by mechanical means must be with hoisters proper as for weight as well as for shape and volume. Hoisters,
ropes and hooks used must contain clear indications on maximum carrying capacity acceptable. The use of said means
is compulsorily permitted to authorised personnel only. Stay duly clear of the load, and, anyhow, never under it.
In disassembling operations, always observe provided prescriptions; prevent mechanical parts being taken out from
accidentally striking workshop personnel.
Workshop jobs performed in pairs must always be performed in maximum safety; avoid operations which could be
dangerous for the co-operator because of lack of visibility or of his/her not correct position.
Keep personnel not authorised to operations clear of working area.
You shall get familiar with the operating and safety instructions for the assembly prior to operating on the latter. Strictly
follow all the safety indications found on the assembly.
Do not leave the running assembly unattended when making repairs.
When carrying out work on the assembly lifted off the ground, verify that the assembly is firmly placed on its supporting
stands, and that the manual/automatic safety devices have been actuated in the event that the assembly is to be lifted
by means of a hoist.
When you have to operate on assemblies powered by natural gas, follow the instructions contained in the document,
as well as all the specific safety standards provided for.
Only remove radiator cap when the engine is cold by cautiously unscrewing it in order to let system residual pressure
out.
Inflammable fuel and all inflammable fluids and liquids must be handled with care, according to what contained on
harmful materials 12-point cards. Refuelling must be performed outdoors with the engine off, avoiding lit cigarettes,
free flames or sparks in order to prevent sudden fires/bursts. Adequately store inflammable, corrosive and polluting
fluids and liquids according to what provided by regulations in force. Compulsorily avoid to use food containers to
store harmful liquids. Avoid to drill or bore pressurised containers, and throw cloths impregnated with inflammable
substances into suitable containers.
Worn out, damaged or consumable parts must be replaced by original spares.
During workshop activity, always keep the work place clean; timely clear or clean floors from accidental liquid or oil
spots. Electric sockets and electric equipment necessary to perform repair interventions must meet safety rules.

Put on, where required by the intervention, garments and protections provided in accident prevention rules; contact
with moving parts can cause serious injuries. Use suitable, preferably tight-fitted garments, and avoid to use jewels,
scarves, etc.
Do not leave the engine in motion at workshop locations not provided with a pipe to scavenge exhaust gas outside.
Avoid to breathe fumes coming from heating or from paint welding because they can cause damages to health; operate
outdoors or in suitably ventilated areas. Put on proper inspirator if paint powder is present.
Avoid contact with hot water or steam coming from the engine, radiator and pipings because they could cause serious
burns. Avoid direct contact with liquids and fluids present in vehicle systems; where an accidental contact has occurred,
refer to 12-point cards for provisions to make.
Clean the assemblies and carefully verify that they are intact prior to overhauling. Tidy up detached or disassembled
parts with their securing elements (screws, nuts, etc.) into special containers.
Check for the integrity of the parts which prevent screws from being unscrewed: broken washers, dowels, clips, etc.
Self-locking nuts with an insert made of nylon must always be replaced.
Avoid contact of rubber parts with diesel oil, petrol or other not compatible substances.
Before washing under pressure mechanical parts, protect electric connectors, and central units, if present.
Tightening screws and nuts must always be according to prescriptions; FPT commercial and assistance network is
available to give all clarifications necessary to perform repair interventions not provided in this document.
Before welding:
- Disconnect all electronic central units, take power cable off battery positive terminal (connect it to chassis
bonding) and detach connectors.
- Remove paint by using proper solvents or paint removers and clean relevant surfices with soap and water.
- Await about 15 minutes before welding.
- Equip with suitable fire resistant protections to protect hoses or other components where fluids or other
materials flow which may catch fire easily on welding.
Should the vehicle be subjected to temperatures exceeding 80C (dryer ovens), disassemble drive electronic central
units.
The disposal of all liquids and fluids must be performed with full observance of specific rules in force.

GENERAL WARNINGS ON THE ELECTRIC SYSTEM
If an intervention has to be made on the electric/electronic system, disconnect batteries from the system; in this case,
! always disconnect, as a first one, the chassis bonding cable from batteries negative terminal.
Before connecting the batteries to the system, make sure that the system is well isolated.
Disconnect the external recharging apparatus from the public utility network before taking apparatus pins off battery
terminals.
Do not cause sparks to be generated in checking if the circuit is energised.
Do not use a test lamp in checking circuit continuity, but only use proper control apparatuses.
Make sure that the electronic devices wiring harnesses (length, lead type, location, strapping, connection to screening
braiding, bonding, etc.) comply with FPT system and are carefully recovered after repair or maintenance interventions.
Measurements in drive electronic central units, plugged connections and electric connections to components can only
be made on proper testing lines with special plugs and plug bushes. Never use improper means like wires, screwdrivers,
clips and the like in order to avoid the danger of causing a short circuit, as well as of damaging plugged connections,
which would later cause contact problems.
To start up the engine, do not use fast chargers. Start up must only be performed with either separate batteries or
special truck.
A wrong polarisation of supply voltage in drive electronic central units (for instance, a wrong polarisation of batteries)
can cause them to be destroyed.
Disconnect the batteries from the system during their recharging with an external apparatus.
On connecting, only screw up connector (temperature sensors, pressure sensors etc.) nuts at prescribed tightening
torque.
Before disconnecting the junction connector from an electronic central unit, isolate the system.
Do not directly supply electronic central units servo components at nominal vehicle voltage.
Cables must be arranged such as to result to be parallel to reference plane, i.e. as close as possible to chassis/body
structure.
Once the intervention on the electric system has been completed, recover connectors and wiring harnesses according
to original arrangement.
NOTE Connectors present must be seen from cable side. Connectors views contained in the manual are representative of
cable side.

Bonding and screening

Negative leads connected to a system bonded point must be both as short and possible and star-connected to each other,
trying then to have their centering tidily and properly made (Figure 1, re. M).
Further, following warnings are to be compulsorily observed for electronic components:
- Electronic central units must be connected to system bonding when they are provided with a metallic shell.
- Electronic central units negative cables must be connected both to a system bonding point such as the dashboard opening
bonding (avoiding serial or chain connections), and to battery negative terminal.
- Analog bonding (sensors), although not connected to battery negative system/terminal bonding, must have optimal isolation.
Consequently, particularly considered must be parasitic resistances in lugs: oxidising, clinching defects, etc.
- Screened circuits braiding must only electrically contact the end towards the central unit entered by the signal (Figure 2).
- If junction connectors are present, unscreened section d, near them, must be as short as possible (Figure 2).
- Cables must be arranged such as to result to be parallel to reference plane, i.e. as close as possible to chassis/body structure.
Figure 1
1. NEGATIVE CABLES STAR CONNECTION TO SYSTEM BONDING M
Figure 2
88039
2. SCREENING THROUGH METALLIC BRAIDING OF A CABLE TO AN ELECTRONIC COMPONENT C. CONNECTOR

d. DISTANCE ! 0

CONVERSIONS BETWEEN THE MAIN UNITS OF MEASUREMENT OF THE

INTERNATIONAL SYSTEM AND MOST USED DERIVED QUANTITIES
Power
1 kW = 1.36 metric HP
1 kW = 1.34 HP
1 metric HP = 0.736 kW
1 metric HP = 0.986 HP
1 HP = 0.746 kW
1 HP = 1.014 metric HP
Torque
1 Nm = 0.1019 kgm
1 kgm = 9.81 Nm
Revolutions per time unit
1 rad/s = 1 rpm x 0.1046
1 rpm = 1 rad/s x 9.5602
Pressure
1 bar = 1.02 kg/cm2
1 kg/cm2 = 0.981 bar
1 bar = 105 Pa
Where accuracy is not particularly needed:
- Nm unit is for the sake of simplicity converted into kgm according to ratio 10:1
1 kgm = 10 Nm;
- bar unit is for the sake of simplicity converted into kg/cm2 according to ratio 1:1
1 kg/cm2 = 1 bar.
Temperature
0 C = 32 F
1 C = (1 x 1.8 + 32) F

KEY OF LECTURE OF THE HEADINGS AND FOOTNOTES
Type of Section Page

vehicle title number
Language Basic edition referred to When month - year

Printout
Publication month - year editorial update is present (revi) to
number
phase closing the basic edition

Part 1
F2C CURSOR ENGINES
Section
General specifications 1
Fuel 2
Industrial application 3
Overhaul and technical specifications 4
Tools 5
Safety prescriptions Appendix


UPDATING
Section Description Page Date of revision


F2C CURSOR ENGINES SECTION 1 - GENERAL SPECIFICATIONS 1
SECTION 1
General Specifications
Page
MAPPING BETWEEN TECHNICAL

AND COMMERCIAL CODING . . . . . . . . . . . . 3
VIEWS OF THE ENGINE . . . . . . . . . . . . . . . . . . . . 5
LUBRICATION DIAGRAM . . . . . . . . . . . . . . . . . . . 8
- Oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
- Overpressure valve . . . . . . . . . . . . . . . . . . . . . 9
- Oil pressure control valve . . . . . . . . . . . . . . . . 10
- Heat exchanger . . . . . . . . . . . . . . . . . . . . . . . . 10
ENGINE OIL FILTER . . . . . . . . . . . . . . . . . . . . . . . . 11
- Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 11
- Lock torques . . . . . . . . . . . . . . . . . . . . . . . . . . 11
- Installation rule . . . . . . . . . . . . . . . . . . . . . . . . . 11
- Filter by-pass valve . . . . . . . . . . . . . . . . . . . . . . 11
- Replacing oil filter cartridge . . . . . . . . . . . . . . . 12
- Oil fume recycle (Blow-by) . . . . . . . . . . . . . . . 13
COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
- Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
- Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
- Water pump . . . . . . . . . . . . . . . . . . . . . . . . . . 16
- Thermostat . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
TURBOCHARGING . . . . . . . . . . . . . . . . . . . . . . . . 17
EGR EXHAUST GAS RECYCLE SYSTEM . . . . . . . . 18
INTERNAL EGR OPERATING ON SUCTION
VALVES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Print P2D32C006 E Base - May 2010

2 SECTION 1 - GENERAL SPECIFICATIONS F2C CURSOR ENGINES
Base - May 2010 Print P2D32C006 E

MAPPING BETWEEN TECHNICAL AND COMMERCIAL CODING
Technical Code Commercial Code

F2CE9687A*E001
F2CE9687B*E001 C87 ENT X
F2CE9687C*E001


VIEWS OF THE ENGINE
Figure 1
144838
LEFT-HAND SIDE VIEW

Figure 2
144839
RIGHT-HAND SIDE VIEW

Figure 3
144840
FRONT HAND SIDE VIEW

Figure 4
144841
REAR HAND SIDE VIEW

Figure 5
144842
TOP VIEW

LUBRICATION DIAGRAM
Figure 6
Dropping oil
Pressure oil
114244

Oil pump Overpressure valve

Figure 7 Figure 9
114245 117716
The oil pump (1) cannot be overhauled. On finding any MAIN DATA TO CHECK THE OVERPRESSURE
damage, replace the oil pump assembly. VALVE SPRING
See under the relevant heading for replacing the gear (2) of
the crankshaft.
Figure 8
112327
OIL PUMP CROSS-SECTION

1. Overpressure valve Start of opening pressure 10.1 0.7 bars.
Oil pressure control valve Figure 11

Figure 10
168 9
308 15
63
51
36.4
73542 88819
The oil pressure control valve is located on the left-hand side MAIN DATA TO CHECK THE OIL PRESSURE
of the crankcase. CONTROL VALVE SPRING
Start of opening pressure 5 bars.
Heat exchanger
Figure 12
114246
1. Exchanger seal - 2. Internal heat exchanger element - 3. Cover - 4. Oil filter - 5. Oil filter seal

ENGINE OIL FILTER

Figure 13
114247
1. Closure cap - 2. Cartridge - 3. Spring - 4. Support O-ring - 5. Tank O-ring - 6. Washer - 7. Washer - 8. Support -
9. Plug M14x1.5 - 10. Plug M38x1.5 - 11. By-pass valve 3.4 bars.
Characteristics Filter by-pass valve

1. Max working pressure: 13 bars Figure 14
2. Working temperature: - 30 C + 120 C
3. By-pass valve opening value: 3,4 0,3 bar
Lock torques
Cap (part 1): 60 5 Nm
Plug (part 9): 30 5 Nm
Plug (part 10): 90 5 Nm
Installation rule
Use threadlock for plug (part 10).
73545
Valve opens quickly at 3,4 0,3 bar pressure.

Replacing oil filter cartridge Figure 17

Dismantling
Figure 15
115878
Move the upper part of the casing thread close to the first
lower thread of the support (the cartridge cover element
should be in contact with the oil outlet duct on the support).
115876 Proceed with tightening the cartridge-casing assembly (1) on
the support (4).
Remove the plug (2).
During this stage both the seal (3) for the oil outlet
Undo the filter casing (1) by a couple of turns and wait for
duct-cartridge element and the casing-support seal (2) will
a few minutes.
gradually be involved.
In this way the remaining oil in the casing starts firstly to drip
Tighten the filter casing to a torque of 65 Nm.
and then to flow smoothly out.
Completely undo the casing and then replace the cartridge.
Figure 18
Refitting
Figure 16
115877
Insert the cartridge in the casing aligning the centering tabs

(2) on the upper plate (1) with the seats.
The cartridge should be pushed into the container until the
action of the attachment system at the bottom of the casing
is overcome. 115879
At the same time, the tabs on the upper plate should slide Tighten the protective cap (1) on the filter casing.
into the housings.

Oil fume recycle (Blow-by)

Part of gas produced by combustion during engine operation leaks through piston elastic ring openings into sump, mixing with
oil fumes in sump.
This mixture, conveyed upward, is partially separated from oil by a device located in timing cover upper part and introduced in
air intake circuit.
The device mainly consists of a rotary filter secured on propeller shaft and by a front cover housing normally closed valves
controlling mixture flow.
Figure 19
Gas with oil contents greater than 10 g/h

Gas with oil contents approx. 0,2 g/h
Condensed oil returning to oil sump
114248

COOLING
Description
The engine cooling system is of the closed-circuit, forced circulation type.
It consists mainly of the following components:
- expansion tank, not supplied (by IVECO);
- a heat exchanger to cool down lubrication oil;
- a water pump with centrifugal system incorporated in the cylinder block;
- fan, not supplied;
- a 2-way thermostat controlling the coolant circulation.
Operation
The water pump is actuated by the crankshaft through a poli-V belt and sends coolant to the cylinder block, especially to the
cylinder head (bigger quantity). When the coolant temperature reaches and overcomes the operating temperature, the
thermostat is opened and from here the coolant flows into the radiator and is cooled down by the fan.
The pressure inside the system, due to temperature change, is adequately controlled through the expansion vessel.

Figure 20
Water flowing out of the thermostat
Water circulating in the engine
Water flowing into the pump
114249

Water pump Figure 23

Figure 21
TO THE HEATER
TO RADIATOR
TO EXPANSION TANK
FROM THE HEAD
45358
Water leaving the thermostat
144832 Check the thermostat works properly; replace it if in doubt.
CROSS-SECTION OF THE WATER PUMP Temperature of start of travel 85 C 1.5 C.

Minimum travel 9.5 mm at 95 C.
The water pump comprises: impeller, shaft with bearing, front
seal, drive pulley.
NOTE Check that the pump body has no cracks or water

leakage; if it does, replace the entire water pump.
Thermostat
View of thermostat operation
Figure 22
TO THE HEATER
TO BY-PASS FROM THE HEAD
45357
Water circulating in the engine

TURBOCHARGING
The turbocharging system consists of:
- air filter;
- Wastegate turbocharger.
Figure 24
Exhaust gas
Compressed air (hot)
Inlet air
Intake compressed air
114251

EGR EXHAUST GAS RECYCLE SYSTEM

The exhaust gas can be partially recycled to cylinders to reduce maximum temperature values of combustion that produce nitro-
gen oxides (NOx).
The exhaust gas recycle system (EGR) reduces combustion temperature and therefore is an efficient NOx emission control
system.
INTERNAL EGR OPERATING ON SUCTION VALVES

The specific design of suction cams of the internal EGR system allows part of exhaust gas to be recycled to engine cylinders.
This type of EGR, called internal EGR, is not equipped with any electronic control, the system is always active. Its configuration
requires no additional parts such as control valves, pipelines or heat exchangers therefore engine profile remains unchanged.
Besides main lobe, suction cam has an additional lobe (3) as to configuration without EGR. During concerned cylinder exhaust
phase, this lobe allows a shaft advanced opening of intake valve (*). In this way, part of the exhaust gas is trapped in the suction
duct and later, during cylinder suction phase, this gas is recycled to cylinder inlet for combustion phase.
Figure 25
Y : Valve lift in mm
X: Crankshaft adjustment
in degrees
Valve tolerance = 0 mm
Valve tolerance = 0,4 mm
114026
1. Exhaust cams - 2. Suction cams - 3. EGR lobe - S. Exhaust ducts - A. Intake ducts

F2C CURSOR ENGINES SECTION 2 - FUEL 1
SECTION 2
Fuel
Page
SUPPLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
FUEL SUPPLY DIAGRAM . . . . . . . . . . . . . . . . . . . . 4
MECHANICAL SUPPLY PUMP . . . . . . . . . . . . . . . 5
- Normal operating conditions . . . . . . . . . . . . . . 5
- Overpressure condition at outlet . . . . . . . . . . . 5
- Drain conditions . . . . . . . . . . . . . . . . . . . . . . . 5
CP3 HIGH-PRESSURE PUMP . . . . . . . . . . . . . . . . . 6
HIGH-PRESSURE PUMP - INSIDE STRUCTURE . . 7
- Operating principle . . . . . . . . . . . . . . . . . . . . . 8
- Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
RAIL (PRESSURE ACCUMULATOR) . . . . . . . . . . . 10
- Electroinjector . . . . . . . . . . . . . . . . . . . . . . . . . 10

2 SECTION 2 - FUEL F2C CURSOR ENGINES

SUPPLY
The Common Rail supply system is equipped with a special pump that maintains fuel at constant high pressure regardless
from phase and cylinder under injection and accumulated in an common duct shared by all electric injectors.
Therefore, fuel at injection pressure, calculated by ECU, is always available at electric injection inlet.
When the solenoid valve of an injector is energized by ECU, in related cylinder the injection of fuel taken directly from the
rail takes place.
Figure 1
Return
circuit
Supply
circuit
144843

FUEL SUPPLY DIAGRAM

Figure 2
High pressure
Low pressure
144820
1. High-pressure pump - 2. Fuel filter - 3.Tank - 4. Fuel pre-filter - 5.ECU - 6. Electric injectors - 7.Common Rail -
8. Pressure sensor
After high-pressure pipeline installation, during the following 20 hours of work, frequently check engine oil level.
!
(IT MUST NOT INCREASE).

MECHANICAL SUPPLY PUMP Drain conditions

Gear pump, fitted on the rear side of the high pressure pump
and used to supply it. Figure 5
It is controlled by high pressure pump shaft.
Normal operating conditions

Figure 3
72594
The by-pass valve (2) cuts in when, with engine off, the fuel
system shall be filled through the priming pump. In this
72592
situation the by-pass valve (1) stays closed whereas by-pass
valve (2) opens due to inlet pressure, and fuel is drained out
A Fuel inlet from tank, B fuel outlet to filter, 1-2 by-pass valves through B.
in close position
NOTE The mechanical supply pump cannot be replaced

individually, therefore it cannot be removed from
the high pressure pump.
Overpressure condition at outlet
Figure 4
72593
The by-pass valve (1) cuts in when overpressure is generated

at outlet B. The existing pressure, overcoming valve spring (1)
elastic strength, makes inlet and outlet communicating
through duct (2).

CP3 HIGH-PRESSURE PUMP

Pump with 3 radial pistons controlled by the timing gear,
without needing any setting. On the rear side of the high
pressure pump is fitted the mechanical supply pump
controlled by the high pressure pump shaft.
The following work must be carried out on the feed pump / high-pressure pump assembly:
- replacing the drive gear;
- replacing the pressure regulator.
Figure 6
72595
1. Fuel outlet fitting to rail - 2. High-pressure pump - 3. Pressure regulator - 4. Control gear - 5. Fuel inlet fitting from filter -
6. Fuel outlet fitting to filter support - 7. Fuel inlet fitting from control unit heat exchanger - 8. Fuel outlet fitting from supply
pump to filter - 9. Mechanical supply pump

HIGH-PRESSURE PUMP - INSIDE STRUCTURE

Figure 7
sec. B-B
sec. C-C
70498
1. Cylinder 2. Three-lobe element 3. Cap intake valve 4. Ball delivery valve 5. Piston 6. Pump shaft
7. Low-pressure fuel inlet 8. Pumping elements supplying fuel ducts
Every pumping unit is composed of: translated in a circular movement along a wider radius, with
the resulting alternate actuation of the three pumping
- a piston (5) actuated by a three-lobe element (2) floating
elements;
on the pump shaft (6). The element (2), being floating
on a misaligned part of the shaft (6), when the shaft - cap intake valve (3);
rotates, does not rotate therewith but is only
- ball delivery valve (4).

Operating principle
Figure 8
Sec. B B
Sec. D D
72597
1. Fuel outlet fitting to rail - 2. Delivery valve to rail - 3. Pumping element - 4. Pump shaft - 5. Pumping element supply duct -
6. Pressure regulator supply duct - 7. Pressure regulator
Pumping element (3) is oriented to pump shaft (4) cam. the PWM signal received from ECU. During pumping
During intake, the pumping element is supplied through element compression stage, fuel reaches the pressure
supply duct (5). The fuel amount to be sent to the pumping required to open the delivery valve to common rail (2) and
element is set by the pressure regulator (7). The pressure to feed it through outlet (1).
regulator meters fuel flow to pumping element according to

Figure 9 Figure 10
72598 72601
Sec. C C Sec. A A
1. Pumping element inlet - 2. Pump lubrication ducts - 1. Fuel outlet duct - 2. Fuel outlet duct - 3. Fuel outlet
3. Pumping element inlet - 4. Main pumping element from pump with high pressure pipe fitting for common rail
supply duct - 5. Pressure regulator - 6. Pumping element
inlet - 7. Regulator exhaust duct - 8. 5 bar pressure relief
valve - 9. Fuel drain from regulator inlet
Figure 9 shows low pressure fuel paths inside the path and Figure 10 shows high pressure fuel flow through pumping
highlights: main pumping element supply duct (4), pumping element outlet ducts.
element supply ducts (1 3 6), pump lubrication ducts (2),
pressure regulator (5), 5 bar pressure relief valve (8) and fuel
drain duct (7).
Pump shaft is lubricated by fuel through delivery and return
ducts (2).
Pressure regulator (5) establishes the fuel amount to send to
pumping elements; excess fuel is drained out through duct
(9).
5 bar pressure relief valve acts as fuel exhaust manifold and
keeps 5 bar constant pressure at regulator inlet.

Operation RAIL (PRESSURE ACCUMULATOR)

The cylinder is filled through the cap intake valve only if the
supply pressure is suitable to open the delivery valves set on Figure 11
the pumping elements (about 2 bars).
The amount of fuel supplying the high-pressure pump is
metered by the pressure regulator, placed on the
low-pressure system; the pressure regulator is controlled by
the EDC7 control unit through a PWM signal.
When fuel is sent to a pumping element, the related piston
is moving downwards (suction stroke). When the piston
stroke is reversed, the intake valve closes and the remaining
fuel in the pumping element chamber, not being able to come
out, is compressed above the supply pressure value existing
in the rail. 144833
The thereby-generated pressure makes the exhaust valve

open and the compressed fuel reaches the high-pressure 1. Rail - 2. Fuel return - 3.Pipelines to injectors - 4. Fuel
circuit. supply to high pressure pump - 5. Pressure sensor -
6. Overpressure valve
The pumping element compresses the fuel till the top dead
center (delivery stroke) is reached. Afterwards, the pressure The rail volume is of reduced sizes to allow a quick
decreases till the exhaust valve is closed. pressurisation at startup, at idle and in case of high flow-rates.
The pumping element piston goes back towards the bottom It anyway has enough volume as to minimise use of plenum
dead center and the remaining fuel is decompressed. chambers caused by injectors openings and closings and by
the high-pressure pump operation. This function is further
When the pumping element chamber pressure becomes less enabled by a calibrated hole being set downstream of the
than the supply pressure, the intake valve is again opened and high-pressure pump.
the cycle is repeated.
A fuel pressure sensor (5) is screwed to the rail. The signal
The delivery valves must always be free in their movements, sent by this sensor to the electronic control unit is a
free from impurities and oxidation. feed-back information, depending on which the rail pressure
The rail delivery pressure is modulated by the electronic value is checked and, if necessary, corrected.
control unit, through the pressure regulator solenoid valve.
The pump is lubricated and cooled by the fuel.
The radialjet pump disconnection reconnection time on
the engine is highly reduced in comparison with traditional Electroinjector
injection pumps, because it does not require setting.
Figure 12
If the pipe between fuel filter and high-pressure pump is to
be removed-refitted, be sure that hands and components are
absolutely clean.
114255
1. Fuel return hole - 2. Fuel supply

F2C CURSOR ENGINES SECTION 3 - INDUSTRIAL APPLICATION 1
SECTION 3
Industrial application
Page
CLEARANCE DATA . . . . . . . . . . . . . . . . . . . . . . . 3
PART ONE -
MECHANICAL COMPONENTS . . . . . . . . . . . 5
ENGINE DISASSEMBLY ON BENCH . . . . . . . . . . 7
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
- High pressure pump installation . . . . . . . . . . . 15
ENGINE FLYWHEEL . . . . . . . . . . . . . . . . . . . . . . . 15
- Engine flywheel installation . . . . . . . . . . . . . . . 15
- Camshaft installation . . . . . . . . . . . . . . . . . . . . 16
TIMING CAMSHAFT AND FLYWHEEL USING

TOOL 99395223 . . . . . . . . . . . . . . . . . . . . . . . . 17
- Timing camshaft . . . . . . . . . . . . . . . . . . . . . . . 17
- Timing flywheel . . . . . . . . . . . . . . . . . . . . . . . . 19
TIMING CAMSHAFT AND FLYWHEEL

WITHOUT TOOL 99395223 . . . . . . . . . . . . . . 19
- Timing camshaft . . . . . . . . . . . . . . . . . . . . . . . 19
- Timing flywheel . . . . . . . . . . . . . . . . . . . . . . . . 22
- Intake and exhaust rocker arm clearance

adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
ENGINE ASSEMBLY COMPLETION . . . . . . . . . . . 25
PART TWO -
ELECTRICAL EQUIPMENT . . . . . . . . . . . . . . . 27
COMPONENTS ON THE ENGINE F2C . . . . . . . . 29
ENGINE CABLE . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
EDC 7 UC31 CONTROL UNIT PIN-OUT . . . . . . 31
EDC 7 UC31 ELECTRONIC CONTROL UNIT . . 32
EDC CONTROL UNIT PIN-OUT . . . . . . . . . . . . . 33
- Electric injector connector A . . . . . . . . . . . . 33
- Sensor connector C . . . . . . . . . . . . . . . . . . . 34
- Electroinjectors . . . . . . . . . . . . . . . . . . . . . . . . 35
- Engine coolant temperature sensor . . . . . . . . 36
- Fuel temperature sensor . . . . . . . . . . . . . . . . . 37

2 SECTION 3 - INDUSTRIAL APPLICATION F2C CURSOR ENGINES
Page
- High pressure pump (pressure regulator) . . . . 38
- Flywheel pulse transmitter . . . . . . . . . . . . . . . 39
- Distribution pulse transmitter . . . . . . . . . . . . . 40
- Oil temperature/pressure sensor

(42030 /47032) . . . . . . . . . . . . . . . . . . . . . . . 41
- Air pressure/temperature sensor (85156) . . . 42
- Fuel pressure sensor on rail . . . . . . . . . . . . . . 43
- Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
- Starting motor . . . . . . . . . . . . . . . . . . . . . . . . 45
EDC SYSTEM FUNCTIONS . . . . . . . . . . . . . . . . . 46
PART THREE - TROUBLESHOOTING . . . . . . . . 49
PREFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
DIAGNOSTIC EQUIPMENT . . . . . . . . . . . . . . . . . 52
- PT-01 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
- PT - BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
FAULT CODES . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
PART FOUR -
MAINTENANCE PLANNING . . . . . . . . . . . . . 57
MAINTENANCE PLANNING . . . . . . . . . . . . . . . . 59
- Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
- Planning of controls and periodical

intervention . . . . . . . . . . . . . . . . . . . . . . . . . . 59
OFF-PLANE OPERATIONS . . . . . . . . . . . . . . . . . . 61
MAINTENANCE PROCEDURES . . . . . . . . . . . . . 62
- Checks and controls . . . . . . . . . . . . . . . . . . . . 62

CLEARANCE DATA
F2CE9687
Type
A*E B*E C*E
Cycle 4-stroke Diesel engine

Fuel feed Turbocharged
Injection Direct
No. of cylinders 6 in line

Bore mm 117
Stroke mm 135
+ + + Total displacement cm3 8710
Compression ratio 1: 15.9 0.8
Maximum kW 260 230 200

power (CV) 354 313 272
rpm 2100 2100 2100
Max. torque Nm 1500 1400 1300

(kgm)
rpm 1400 1400 1400
Loadless
engine
idling rpm -
Loadless engine
peak rpm -
Intercooler
SUPERCHARGING Direct injection
HX40
Turbocharger type
LUBRICATION
Oil pressure Forced by gear pump, relief valve single action

bar (warm engine) oil filter
- idling bar -
- peak rpm bar -
COOLING Liquid
Water pump control Through belt
Thermostat
- start of opening C 85
NOTE Data, features and performances are valid only if the setter fully complies with all the installation prescriptions provided
by FPT.
Furthermore, the users assembled by the setter shall always be in conformance to couple, power and number of turns
based on which the engine has been designed.


PART ONE -
MECHANICAL COMPONENTS


ENGINE DISASSEMBLY ON BENCH Figure 3
NOTE Before installing engine on rotary stand 99322230,

remove parts that might interfere with the
installation of brackets 99361042.
Therefore, remove heat exchanger and oil line as
shown below.
Figure 1
114007
If air conditioner compressor is installed, cut belt (2) as it must

not be reused.
Use specific tool (1) and operate in the arrow direction to
remove water pump and alternator control belt (5).
Remove screws and separate pulleys (3) and (6) with damping
flywheel (4).
114017
Under heat exchanger (2) place a container for engine coolant

drain.
Unlock retaining screws and remove heat exchanger assembly
(2).
Remove oil outlet line (1).
Install engine on rotary stand 99322230.
Drain sump oil in specific container. Figure 4
Figure 2
114008
Remove parts below:
114016
- alternator (1);
Unlock retaining screws (2) and remove head cover (1) to - belt tensioner (2);
reach injector and rail wiring. - if present, air conditioner compressor (3);
Remove wiring from all components shown in Electric - water pump (6);
equipment section.
- flanged pipe (4);
- fixed belt tensioner (5);
- thermostat assembly (7).

Figure 5 Figure 7
114551 114012
Apply extractor 99340051 (2) and remove seal (1). Remove parts below:
Unlock screws and remove front cover (3). - fuel filter (3);
- oil level rod (2);
- intake manifold (1).
Figure 8
Figure 6
114013
Disconnect line (1) from high pressure pump support and

remove ECU (2) with support below.
Figure 9
114010
Remove parts below:
- oil filter (1);
- oil inlet line (2);
- turbocompressor (4) and exhaust manifold (3). 114015
On opposite engine side, remove start-up motor. Remove screws (1) and blow-by box (2).

Figure 10 Figure 12
114014
114018
Disconnect fuel lines (2), unlock retaining screws and remove
Unlock screws (2) and remove cover (1). Remove centrifugal high pressure pump (1). Remove fuel filter support (3)
filter (3) below. complete with pipeline.
Figure 13
Figure 11
114020
Unlock screws (1) and remove thrust plate (2).

Use specific spanner to unlock screws (4) and remove relay
gear (5).
Remove high pressure pump mount flange (3).
Figure 14
114019
Use specific spanner to unlock screws (2) and remove gear (3)
complete with tune wheel.
Unlock nut (4) and remove control gear (5) of high pressure
pump.
Remove rpm sensor (1).
NOTE In case removal of gear (5) is difficult, release high

pressure pump screws with light beater strokes on 114009
control shaft and remove gear (5). Use specific tool lock engine flywheel (2) rotation, unlock
retaining screws (1) and remove engine flywheel.

Figure 15 Figure 18
45257 114022
Apply extractor 99340054 (2) and remove seal (1). Unlock screws (1) and remove flywheel box (2).
Figure 19
Figure 16
114023
114029 Remove screws (2) and double gear (3).

Remove retaining screw (5) and connecting rod (4).
Unlock screws (1) and remove engine oil sump (3) complete
with spacer (2) and seal. Remove oil pump (1).
Figure 17 Figure 20
114024
114031b - Unlock rocker arm shaft retaining screws (4).

Unlock screws and remove suction rose (1). - Disconnect fuel pipelines (1) from injector rail, fuel supply
line (2) of high pressure pump to rail and return line (3).

Figure 21 Figure 24
114025
Apply tool 99360558 (1) to rocker arm shaft (2) and remove
shaft, remove crosspieces (3) from cylinder head.
117690
Figure 22 Clean the surface of the parts to be joined removing impurities

and oil residuals. Apply silicon LOCTITE 275 (1) to the cover
(2) as shown in the picture.
The diameter of the sealing string must be 1.5 0.5/0.2.
Fit the front cover within 10 minutes after applying

the sealer.
114027
Remove retaining brackets (3) and remove injectors (4).

Remove retaining screws (1) and remove rail (2).
ASSEMBLY
Figure 23
Figure 25
114257
45266
Remove camshaft and remove cylinder head retaining screws. Install front cover (1) and lock retaining screw at required
torque.
Use metallic ropes to lift cylinder head (1) and remove seal (2).

Figure 26 Figure 29
114258 45267
Secure seal (1), install special tool 99346260 (2), lock nut (3) - Pre-lock by torque wrench (1):
to secure seal (1). 1st phase: 50 Nm (5 kgm);
2nd phase: 100 Nm (10 kgm).
Figure 27 Figure 30
42566 45268
Check that pistons 1-6 are exactly at T.D.C. - Angle locking by means of tool 99395216 (1):
Place seal (2) on cylinder block. 3rd phase: 90 angle
Install cylinder head (1) and lock screws as shown in figures 4th phase: 75 angle.
below.
Figure 31
Removed screws must not be used again. Employ
new screws only.

Figure 28
145833
Install oil pump (1), double gear (3) complete with connecting
114259
rod (4) and lock screws (2) in two phases:
pre-lock 30 Nm
Cylinder head retaining screw locking sequence diagram. 90 angle lock

Figure 32
114260
5. Fit pipes on injectors and head locking fittings by hand.

The previously removed pipes ca no longer be refit
and must be replaced. 6. Lock fittings on rail (A, C) at required torque .
7. Lock fittings on injectors and head (B, C) at required
torque.
Lubricate the injector fastening O-Rings using the
following lubricants: PDE SILIKONFETT 22, NLG
12, PDE LUBRICOMET GR 220 NLG12. TYPE DESCRIPTION LOCK TORQUE
A M18 x 1.5 40 2 Nm
1. Install rail on cylinder head and lock retaining screws by B M14 x 1.5 35 2 Nm
hand.
C M16 x 1.5 40 2 Nm
2. Install injectors in correct position and lock to required
torque.
Check that the injectors (2) are equidistant from the

! springs (1). Distance X which separates them
should always be the same. After fitting the high-pressure pipelines, during the
! following 20 hours of work, frequently check engine
3. Install pipes on rail and lock fittings by hand. oil level (IT MUST NOT INCREASE).
4. Lock rail to cylinder head retaining screws at required
torque.

Figure 33 Figure 35
114261
Clean surfaces to be coupled to remove dirt and oil residuals.

Apply LOCTITE 275 (2) silicone on gear casing (1) as shown 114263
in the figure.
The sealant seam diameter must be 1.5 0.5/0.2 mm. Clean surfaces to be coupled to remove dirt and oil residuals.
Apply LOCTITE 275 silicone on gear casing (1) as shown in
the figure.
Install gear casing within 10 min. from sealant The sealant seam diameter must be 1.5 0.5/0.2 mm.
! application.
Install gear casing within 10 min. from sealant

! application.
Figure 34
Figure 36
114264
114262
Apply gage 99395221 (1) to check and adjust position of
high-pressure pump connection flange (2).
Use torque wrench to lock screws (1) at required torque.
Fix flange screws (2) at required torque.

High pressure pump installation Figure 38

Figure 37
45258
114272
Secure seal (1), install special tool 99346260 (2), lock nut (3)
Install high-pressure pump (1) on flange (2). to secure seal.
Engine flywheel installation

ENGINE FLYWHEEL
NOTE If toothing on engine flywheel for engine start-up is NOTE Crankshaft has a reference pin that must match with
very damaged, change crown wheel. related housing on engine flywheel.
Refit crown wheel after heating up at approx.
200C.
Figure 39
114265
DETAIL OF PISTON POSITION STAMPING ON ENGINE FLYWHEEL

A. Hole on flywheel with a notch corresponding to pistons 3-4 TDC - B. Hole on flywheel with a notch, corresponding to
piston 1-6 TDC - C. Hole on flywheel with a notch corresponding to pistons 2-5 TDC - D. Hole on flywheel with 2 notches,
position corresponding to 54.

Figure 40 This condition is obtained when:

1. the opening with one reference (5) for the engine
flywheel (4) is visible from the inspection window;
2. tool 99360612 (1), through housing (2) of engine rpm
sensor, inserts in hole (3) drilled on engine flywheel (4).
Otherwise, adjust engine flywheel orientation (4).
Remove too 99360612 (1).
145832
Position flywheel (1) on crankshaft, lubricate screws (2)

threading with engine oil and lock them.
Stop rotation using specific tool.
Lock screws (2) in three phases.
1st phase: pre-lock with torque wrench (3) at 100 Nm torque
(10 kgm).
Figure 41 Figure 43
49036
2nd phase: 60 angle locking using tool 99395216 (1).
Camshaft installation
Figure 42
114267
Install camshaft (3) and orient it with references ()

positioned as in the figure.
Clean the matching surfaces of the plate (1) to remove
impurities and oil residues.
Apply silicon LOCTITE 275 (6) on the plate (1) as shown in
the picture.
NOTE Take care NOT to get sealant on the inner groove

(5).
The diameter of the sealant bead should be 1.5 - 0.5/0.2 mm.

Fit the plate (1) within 10 mins of applying the sealant with the
72436
gasket (2) and tighten the bolts (4) to the recommended
Position crankshaft with pistons 1 and 6 at TDC. torque.

Figure 44 TIMING CAMSHAFT AND FLYWHEEL

USING TOOL 99395223
Timing camshaft
Figure 46
114269
Apply gage 99395222 (1), check and adjust position of

connecting rod (3) for relay gear, lock screw (2) at required
torque.
115064
Rotate the crankshaft with the tool 99360341 (3, Figure 53)
so that the opening marked with two references (5) is visible
from the lower inspection window in the flywheel cover
casing.
In this condition, insert the tool 99360612 (1) via the housing
(2) for the engine rpm sensor in the opening (3) in the engine
flywheel (4).
Figure 45 Figure 47
114270 116052
Refit relay gear (2) and lock screws (1) using six-splined Fit the tool 99395223 (1) at the front of the camshaft.
spanner at required torque.
NOTE The relay gear (2) bushing can be replaced when

worn out. After securing bushing, grind it to reach
dia. 58.010 0.10 mm.

Figure 48 Figure 50
116053 116055
Install crosspieces (1) on valve rod.

Rotate the tool (1) 99395223 in order to insert the pin (3) in
the opening (2, Figure 47) in the head. Fasten the tool (1)
99395223 using two M8x1.25 bolts (2). NOTE Before refitting rocker arm shaft assembly, check
that all adjustment screws have been fully unlocked.
Figure 49 Figure 51
114025
117691
Apply tool 99360558 (1) to rocker arm shaft (2) and install
Fit the camshaft drive gear (1) so that the fastening openings shaft on cylinder head.
in the shaft are aligned with the slots (2) in the drive gear. Lock retaining screws at required torque.
Position the gear (1) taking care to position the spokes (4) as
illustrated. This operation is necessary in order to be able to
fit the flywheel correctly which can only be fitted in one
position in relation to the gear.
Tighten the fixing bolts (3).

Timing flywheel TIMING CAMSHAFT AND FLYWHEEL

WITHOUT TOOL 99395223
Figure 52
Timing camshaft
Figure 53
145834
Fit the high pressure pump gear (5) tightening the nut (4) to
torque.
Use the flat washer (PN 17095914) in conjunction with the
nut (4) replacing the one supplied with the Bosch CP3 pump.
Fit the flywheel (6) so that the toothe marked with the arrow
() is in line with the sensor housing (2).
To check that the position is correct, insert tool (1) 99360613
in the timing sensor (2) housing.
Proceed with tightening the bolts (3). 114279
Remove the tools 99395223, 99360612 and 99360613. Secure special tool 99360341 (3) to gear casing.
NOTE The arrow indicated engine rotation direction.

Use tool above to rotate engine flywheel (1) in
engine rotation direction to bring cylinder 1 piston
approx. to TDC in blast phase.
This condition is reached when hole with notch (4),
following hole with two notches (5) drilled on
engine flywheel (1), is visible through manhole (2).
Figure 54
71774
The exact position of piston no.1 at TDC is obtained when,

in conditions described above, tool 99360612 (1), through
engine rpm sensor housing (2), inserts in hole (3) drilled on
engine flywheel (4).
Otherwise, rotate engine flywheel (4) to adjust its orientation.

Figure 55 Figure 57
114276
Install crosspieces (1) on valve rod.
NOTE Before refitting rocker arm shaft assembly, check

that all adjustment screws have been fully unlocked.
Figure 58
115063
Rotate the camshaft so that the openings at the rear of the

engine are arranged in the configuration illustrated in the
diagram.
Figure 56
114025
Apply tool 99360558 (1) to rocker arm shaft (2) and install
shaft on cylinder head.
Lock retaining screws at required torque.
Remove tool 99360612 (1, Figure 54).
Figure 59
117691
Install gear (1) controlling camshaft so that fastening holes on

shaft coincide with slots (2) on control gear.
NOTE Position the gear (1) taking care to position the

spokes (4) as illustrated.
This operation is necessary in order to be able to fit
the flywheel correctly which can only be fitted in one
position in relation to the gear.
117693
Clean the surface of the parts to be joined removing impurities

and oil residuals. Apply silicon LOCTITE 275 (1) on the front
Lock retaining screws (3). cover (2) as shown in the picture. The diameter of the sealing
string must be 1.5 0.5/0.2 mm.

Figure 60 Figure 62
115064
Rotate crankshaft to check conditions below: 115064

1) hole identified with two notches (5) is visible through Camshaft is timed if conditions below are found at cam lift
manhole; values 4.70 0.05:
2) fixture 99360612 (1) through housing (2) of engine rpm 1) hole identified with two notches (5) is visible through
sensor inserts in hole (3) on engine flywheel (4). manhole;
2) fixture 99360612 (1) through housing (2) of engine rpm
sensor inserts in hole (3) on engine flywheel (4).
NOTE To recover the clearances, rotate the crankshaft in
a clockwise direction until the opening with the two
references is passed and then rotate in the opposite
direction to produce the conditions described
above.
Figure 63
Figure 61
106535
Position the dial gauge with a magnetic base (1) with the 114281
(flat-based) rod positioned on the roller (2) for the rocker
arms which controls the exhaust valve for cylinder no. 3 and
apply a pre-loading of 6 mm. In case conditions shown in Figure 62 and shown at paras 1
and 2 are not found, operate as follows:
NOTE During the measurement the rod for the dial gauge 1) release screws (2) securing gear (1) of camshaft to as to
should always be perpendicular to the engine axis make control gear and camshaft independent;
and NOT to the surface of the head. 2) conveniently operate on engine flywheel so as to obtain
Using tool 99360341 (3, Figure 53), rotate crankshaft conditions indicated at paras 1 and 2, Figure 62,
clockwise till dial gage arrow reaches minimum value (max considering that cam lift value must remain unchanged;
cam lift), after which it no longer varies. 3) lock screws (2) and repeat control as already described;
Zero set dial gage. 4) lock screws (2) at required torque.
Rotate engine flywheel anticlockwise till dial gage reads
camshaft cam lift value = 4.70 0.05 mm.

Timing flywheel Figure 65

Figure 64
114275
NOTE Pipes previously removed ca no longer be refit.

Change them.
Install fuel supply pipeline (1) from high pressure pump to rail.
Lock nuts at 35 Nm torque.
After high-pressure pipe installation, during the

! following 20 hours of work, frequently check engine
oil level (IT MUST NOT INCREASE).
Figure 66
145835
Install gear (5) of high pressure pump and lock nut (4) at
required torque.
NOTE When refitting, use the flat washer (PN 17095914)

in conjunction with the nut (4) replacing the one
supplied with BOSCH pump CP3.
Rotate crankshaft and bring cylinder n.1 piston to compression

phase at TDC: Rotate flywheel opposite to regular rotation 114285
direction by 1/4 of rev. Install centrifugal filter (1) on tune wheel and lock screws (2)
Rotate flywheel again in regular rotation direction till hole at required torque.
identified by double notch (3, Figure 64, second box) shows
through inspection hole under flywheel cover box. Figure 67
Insert tool 99360612 (1, Figure 64, second box) in flywheel
sensor housing (2, Figure 64, second box).
Fit the flywheel (6) so that the tooth marked with the arrow
() is in line with the sensor housing (2, Figure 64, first box).
Insert tool 99360613 (1, Figure 64, first box) through phase
sensor housing (2, Figure 64, first box) on tooth machined on
tune wheel.
In case tool (1, Figure 64, first box) is difficult to insert, unlock
screws (3, Figure 64, first box) and orient tune wheel (6) to
properly match the tooth (1, Figure 64, first box).
114286
Lock screws (3, Figure 64, first box).
Install timing cover (1) and lock retaining screws (2) at
required torque.

Intake and exhaust rocker arm clearance Figure 69

adjustment
Figure 68
114287 114288
Install blow-by body (1) with related seal and lock screws (2)
Adjustment of clearance between rocker arms and at required torque.
intake/exhaust valve control crosspieces must be performed
with utmost care. Bring to blast phase cylinder to be adjusted; Install cover (3) and lock screws (4) at required torque.
the valves of this cylinder are closed while the symmetric
cylinder valves are balanced. Symmetric cylinders are 1-6; 2-5
and 3-4.
In order to perform these operations correctly, refer to Figure 70
procedure and table below.
- Use a polygonal spanner to release lock nut (1) of rocker
arm adjustment screw (2).
- Insert filler gage (3) having same value of operating
clearance shown in Characteristic and data tables.
- Use special spanner to lock/unlock adjustment screw.
- Check that filler gage (3) slides with a low friction.
- Lock nut (1) retaining the adjustment screw.
IGNITION ORDER 1-4-2-6-3-5

START AND BALANCE ADJUST
ROTATION VALVES OF CLEARANCE OF
CLOCKWISE CYLINDER No. VALVES
CYLINDER No.
1 and 6 at TDC 6 1
120 3 4
120 5 2
120 1 6
120 4 3
120 2 5
117692
NOTE In order to correctly carry out adjustments above, Clean the surface of the parts to be joined removing impurities
it is mandatory to perform the sequence indicated and oil residuals. Apply silicon LOCTITE 406 within the check
in the table, checking exact positioning at each phase valve (2) housing (1) and on the Blow-by (3) as shown in the
by means of pin 99360612. picture.

Figure 71 Figure 72
114016
Install cylinder head cover (1) and lock screws (2) at required
115880 torque following order shown in Figure 73 diagram.
Fit the head internal electric wire (injectors+pressure sensor)

passing it through the opening (5, Figure 69) and securing it Figure 73
using bands as illustrated in the diagram ().
17 14 13 1 4 5 8
18 9
19 10
20 11
16 15 12 2 3 6 7
Figure 74
117695
Rotate the engine

Before assembling the suction rose, it is necessary to seal the contact area (1) between basement, flywheel casing and front cover
with LOCTITE, following the herein instructions. Clean the surfaces of the parts to be joined removing impurities and oil residuals.
Apply silicon LOCTITE 275 (1) as shown in the picture. The diameter of the sealing string must be 1.5 0.5/0.2 mm.

Figure 75 ENGINE ASSEMBLY COMPLETION

Complete engine assembly fitting or connecting parts below:
- complete fuel filter support and pipelines;
- EDC ecu;
- intake manifold with pre-heating resistor;
- heat exchanger;
- exhaust manifold;
- turbocharger and related water and oil;
- pulley and damper flywheel assy (install fixed guide pulley
5, Figure 4, before assy);
- thermostat assy;
- belt tensioner, water pump, alternator;
- oil level rod;
- start-up motor;
114031b
Install suction rose (1). - oil filter;
- electric connections and sensors (See diagram on page
30).
Figure 76
NOTE Fittings of pipelines, cooling water and turbocharger

lube oil must be locked at:
- 35 5Nm, water pipeline fittings;
- 55 5Nm, oil pipeline female fitting;
- 20-25 Nm, oil pipeline make fitting.
Figure 77
114029
Fit seal on oil sump (3), fit spacer (2) and install sump on engine
block locking screws (1) at required torque.
114291
Use specific equipment (2) to install belt (1) on belt tensioner,

in direction shown by arrow.
NOTE Belt tensioner is automatic, therefore no further

adjustments are required after installation.


PART TWO -
ELECTRICAL EQUIPMENT


COMPONENTS ON THE ENGINE F2C
Figure 78
114294
A. Fuel temperature sensor - B. Engine rpm sensor on camshaft - C. Starter motor - D. EDC 7 control unit -
E. Conditioner compressor - F. Pressure/temperature transmitter - G. Temperature/air pressure sensor -
H. Alternator - I. Resistance for engine warming - L. Connector on engine block for connection with electro-injectors -
M. Water temperature sensor - N. Engine speed on flywheel sensor - O. Fuel adjustment valve on high pressure pump

ENGINE CABLE
Figure 79
119974
Sensor code FUNCTION

78247 Fuel injector
85157 Fuel pressure sensor on rail
85153 Engine coolant temperature sensor
85156 Air pressure and temperature sensor
42030 Engine oil pressure sensor
47032 Engine oil temperature sensor
78013 Solenoid valve to adjust pressure
47042 Fuel temperature sensor
48035 Driving shaft sensor
48042 Camshaft sensor
ST Cable routing inside head

EDC 7 UC31 CONTROL UNIT PIN-OUT

Figure 80
119977

EDC 7 UC31 ELECTRONIC CONTROL UNIT
Figure 81
C A
102373
A. Electro-injector connector - B. Chassis connector - C. Sensor connector

EDC CONTROL UNIT PIN-OUT

Electric injector connector A
Figure 82
12 16
6 11
1 5 102374
Colour legend
B black
R red
U blue
W white
P purple
G green
N brown
Y yellow
O orange
E grey
K pink
Pin Function
1 Solenoid valve for electronic cylinder 5 injection
7 -
8 -
9 -
10 -

Sensor connector C
Figure 83
6 8 16 9 15 22
4
Colour legend 5
B black
R red
U blue
W white
P purple
G green
N brown
Y yellow
O orange 1 3 23 30 36 29 102375
E grey
K pink
Pin Function
18 -
9 Engine speed sensor (timing)
10 Engine speed sensor (timing)
11 -
12 Pressure sensor on rail
15 Coolant temperature sensor
16 -
17 -
19 Engine speed sensor (flywheel)
20 -
21 -
22 -
23 Engine speed sensor (flywheel)
24 Engine oil pressure/temperature sensor
25 Air pressure/temperature sensor supply
26 Coolant temperature sensor
27 Engine oil temperature/pressure sensor
29 -
30 -
31 -
33 Air pressure signal from air pressure/temperature sensor
34 Air temperature signal from air pressure/temperature sensor
36 Air temperature signal from air pressure/temperature sensor

Electroinjectors
Figure 84
114255
It is a N.O. solenoid valve.

They are connected to the EDC ECU on connector A.
The resistance of each injector coil is 0.56 - 0.57 Ohm.
The electroinjector can be considered as consisting of 2 parts:
- actuator - atomizer including pressure rod, needle and nozzle;
- control solenoid valve including coil and pilot valve.
The solenoid valve controls atomizer needle lift.
INJECTION START
When coil is energized, lock pin moves upward.
The control volume fuel flows to return duct causing control volume pressure drop.
At the same time, fuel pressure in pressure chamber causes needle uplift and therefore fuel injection in cylinder.
END OF INJECTION
When coil is de-energized, lock pin returns to lock position to look for a force balance such to return to needle close position and
stop injection.

Engine coolant temperature sensor

This N.T.C. type sensor located on the water outlet sump on the engine head left measures coolant temperature for the various
operating logics with a hot or cold engine and identifies injection enrichment requirements for a cold engine or fuel reduction
requirements for a hot engine.
It is connected to electronic center pins 15/26.
Figure 85
104266
Description Cable colour

To EDC center pin 15 (Sensor connector C) K
To EDC center pin 26 (Sensor connector C) Y

Fuel temperature sensor

Specifications
Supplier BOSCH
Max. tightening torque 35 Nm
Figure 86
104267

To pin 18 of EDC control unit (Sensor connector C) O/B
To pin 35 of EDC control unit (Sensor connector C) W/R

High pressure pump (pressure regulator) Figure 87

Pump with 3 radial pistons commanded by timing gear,
requiring no tuning, with rotor supply pump applied on rear
end.
A. Fuel drain outlet fitting to filter support
B. Fuel inlet fitting from ECU heat exchanger
C. Fuel inlet fitting from fuel filter
D. Fuel outlet fitting from supply pump to filter
E. Fuel outlet fitting to rail x
1. High-pressure pump
2. Supply pump
3. Pressure regulator (NO solenoid valve modulated by
ECU with PWM signal).
Pressure regulator
Located at high-pressure pump inlet, on low pressure system,
it modulates the amount of fuel for high-pressure pump supply
based on commands received from ECU.
It mainly consists of parts below:
- trapezoidal-section lock pin;
- valve control pin;
- pre-load valve;
- coils.
A
When no control signal is present, the pressure regulator is
normally open, therefore the high pressure pump is in max 1
delivery condition. B
C
The ECU modulates a PWM control signal to extend or
3
reduce section of fuel supply line to high-pressure pump.
The component cannot be replaced as an individual part, 2
therefore it cannot be removed. D
The quantity of high-pressure supply fuel is metered by a

proportional valve positioned on low-pressure system and it E
is managed by the ECDC 7 ECU.
The delivery pressure to rail is modulated between 250 and
1400 bars by ECU operating on pressure regulator solenoid
valve. 000912t
It is a NO solenoid valve.
Its resistance is 3,2 .
It is connected to ECU pins C5 - C7.

Flywheel pulse transmitter

Specifications
Supplier BOSCH
Max. tightening torque 8 2 Nm
Figure 88
104269

To EDC center pin 19 (Sensor connector C) B
To EDC center pin 23 (Sensor connector C) W

Distribution pulse transmitter

Features
Vendor BOSCH
Torque 8 2 Nm
Resistance 880 920
This induction type sensor located on the camshaft generates signals obtained from the magnetic flow lines that close through
the 6 plus 1 phase teeth of a sound wheel mounted on the shaft.
The electronic center uses the signal generated by this sensor as an injection step signal.
This sensors air gap is NOT ADJUSTABLE.
Figure 89
104269

To EDC center pin 9 (Sensor connector C) W
To EDC center pin 10 (Sensor connector C) R

Oil temperature/pressure sensor (42030 / Figure 90

47032)
This component is identical to the air pressure/temperature
sensor and replaced single sensors 47032 / 42030.
It is fitted onto the engine oil filter, in a horizontal position.
It measures the engine oil temperature and pressure.
The measured signal is sent to the EDC control unit which
controls, in turn, the indicator instrument on the dashboard
(low pressure warning lights / gauge).
Pin (EDC) 24/C - 32/C Power supply
Pin (EDC) 27/C Pressure
Pin (EDC) 28/C Temperature
The engine oil temperature is used only by the EDC control
unit.
50324
Sensor external view
Ref. Description Control unit pin Figure 91
1 Ground 24C
2 Temp. Sign. 28C
3 +5 32C
4 Press. Sign. 27C
50323
Linking connector
Figure 92
50344
Wiring diagram

Air pressure/temperature sensor (85156). Figure 93

This component incorporates a temperature sensor and a
pressure sensor.
IIt replaces the temperature sensors (85155) and pressure
sensors (85154) available in the preceding systems.
It is fitted onto the intake manifold and measures the
maximum supplied air flow rate used to accurately calculate
the amount of fuel to be injected at every cycle.
The sensor is powered with 5 V.
The output voltage is proportional to the pressure or
temperature measured by the sensor.
Pin (EDC) 25/C - 33/C Power supply
Pin (EDC) 36/C Temperature
Pin (EDC) 34/C Pressure
114266
Sensor external view
Figure 94
114273
Linking connector
Figure 95
Ref. Description Control unit pin
1 Ground 25C
2 Temp. Sign. 36C
3 +5 33C
4 Press. Sign. 34C
50344
Wiring diagram

Fuel pressure sensor on rail

Installed on one rail end, it measures actual fuel pressure in order to determine injection pressure.
The injection pressure value is used for pressure check and to determine the injection electric command duration.
It is supplied with 5 volts.
It is connected to ECU on pins 12C - 13C - 14C.
Figure 96
114620
Pin
Ref. Description
ecu
1 ECU pin 12C
2 Ground 13C
3 Supply Pressure 14C

Alternator
Supplier MITSUBISHI
Technical features 24V - 90A
Figure 97 Figure 99
144837 116715
Figure 98 Figure 100
144836 116716
Pin Description
S + 30
L Battery recharge light
B- Negative
B+ Positive
IG + 15

Starting motor
Specifications
Supplier DENSO
Type 2280005641
Electrical system 24 Volt
Nominal output 4.5 Kw
Figure 101
114283

EDC SYSTEM FUNCTIONS

The EDC 7 UC31 electronic center manages the following main functions:
Fuel injection
Accessory functions such as cruise control, speed limiter, PTO and the like
Self-diagnosis
Recovery
It also enables:
Interfacing with other electronic systems (if any) available on the vehicle
Diagnosis
Fuel dosing
Fuel dosing is calculated based on:
- accelerator position
- engine rpm
- quantity of air admitted.
The result can be corrected based on:
- water temperature
or to prevent:
- noise
- fumes
- overloads
- overheating
Pressure can be adjusted in case of:

- engine brake actuation
- external device actuation (e.g. speed reducer, cruise control)
- serious defects involving load reduction or engine stop.
After determining the mass of air introduced by measuring its volume and temperature, the center calculates the corresponding
mass of fuel to be injected into the cylinder involved, with account also taken of gas oil temperature.
Delivery correction based on water temperature
When cold, the engine encounters greater operating resistance, mechanical friction is high, oil is till very viscous and operating plays
are not optimized yet.
Fuel injected also tends to condense on cold metal surfaces.
Fuel dosing with a cold engine is therefore greater than when hot.
Delivery correction to prevent noise, fumes or overloads
Behaviors that could lead to the defects under review are well known, so the designer has added specific instructions to the center
to prevent them.
De-rating
In the event of engine overheating, decreasing delivery proportionally to the temperature reached by the coolant changes injection.

Injection lead electronic control

Injection lead, or the start of fuel delivery expressed in degrees, can differ from one injection to the next, even from one cylinder
to another and is calculated similarly to delivery according to engine load, namely, accelerator position, engine rpm and air admitted.
Lead is corrected as required:
- during acceleration
- according to water temperature
and to obtain:
- reduced emissions, noise abatement and no overload
- better vehicle acceleration
High injection lead is set at start, based on water temperature.
Delivery start feedback is given by injection electro valve impedance variation.
Engine start
Cylinder 1 step and recognition signal synchronization (flywheel and drive shaft sensors) takes place at first engine turns. Accelerator
pedal signal is ignored at start. Star delivery is set exclusively based on water temperature, via a specific map. The center enables
the accelerator pedal, when it detects flywheel acceleration and rpm such as to consider the engine as started and no longer drawn
by the starter motor.
Run Up
When the ignition key is inserted, the center transfers data stored at previous engine stop to the main memory (Cf. After run),
and diagnoses the system.
After Run
At each engine stop with the ignition key, the center still remains fed by the main relay for a few seconds, to enable the
microprocessor to transfer some data from the main volatile memory to an non-volatile, cancelable and rewritable (Eeprom)
memory to make tem available for the next start (Cf. Run Up).
These data essentially consists of:
- miscellaneous settings, such as engine idling and the like
- settings of some components
- breakdown memory
The process lasts for some seconds, typically from 2 to 7 according to the amount of data to be stored, after which the ECU sends
a command to the main relay and makes it disconnect from the battery.
This procedure must never be interrupted, by cutting the engine off from the battery cutout or disconnecting the latter before
10 seconds at least after engine cutout.
In this case, system operation is guaranteed until the fifth improper engine cutout, after which an error is stored in the breakdown
memory and the engine operates at lower performance at next start while the EDC warning light stays on.
Repeated procedure interruptions could in fact lead to center damage.
Cut-off
It refers to the supply cut-off function during deceleration.
Cylinder Balancing
Individual cylinder balancing contributes to increasing comfort and operability.
This function enables individual personalized fuel delivery control and delivery start for each cylinder, even differently between each
cylinder, to compensate for injector hydraulic tolerances.
The flow (rating feature) differences between the various injectors cannot be evaluated directly by the control unit. This information
is provided by the entry of the codes for every single injector, by means of the diagnosis instrument.
NOTE Not present on agricultural versions.
Synchronization search
The center can anyhow recognize the cylinder to inject fuel into even in the absence of a signal from the camshaft sensor.
If this occurs when the engine is already started, combustion sequence is already acquired, so the center continues with the
sequence it is already synchronized on; if it occurs with the engine stopped, the center only actuates one electro valve. Injection
occurs onside that cylinder within 2 shaft revs at the utmost so the center is only required to synchronize on the firing sequence
and start the engine.


PART THREE - TROUBLESHOOTING


PREFACE Every time there is a breakdown claim and this breakdown is

actually detected, it is necessary to proceed inquiring the
A successful troubleshooting is carried out with the electronic unit in one of the ways indicated and then proceed
competence acquired by years of experience and attending with the diagnostic research making trials and tests in order to
training courses. have a picture of the working conditions and identify the root
causes of the anomaly.
When the user complains for bad efficiency or working
anomaly, his indications must be kept into proper In case the electronic device is not providing any indication, it
consideration using them to acquire any useful information to will be necessary to proceed relying on the experience,
focus the intervention. adopting traditional diagnosis procedures.
Using FPT processing instruments, it is also possible to
establish a bi-directional connection with the central unit, by
which not only to decoding the failure codes but also input an
enquiry relying on memory files, in order to achieve any further
necessary information to identify the origin of the anomaly. NOTE Any kind of operation on the electronic center unit
must be executed by qualified personnel, duly
authorized by FPT.
Any unauthorized tamper will involve decay of

after-sales service in warranty.

DIAGNOSTIC EQUIPMENT
PT-01
PT-01 tester should be used with a Laptop but can be also used singly.
Figure 102
117696
1. Connector with 19-pin diagnosis socket - 2. LED signalling communication between the in-strument -
control unit and correct power supply - 3. USB indicator light - 4. Serial port indicator light - 5. Power supply connector
(power only to update SW with serial port).
Using PT-01 with portable tester it is possibile to execute troubleshooting and test the electronic module of engines.
Main functions:
- ECU ID reading;
- Failure memory reading;
- Flight recorder reading;
- Parameters reading;
- Failure memory cleaning;
- Active diagnosis: actuators activation/testing
Operation without a personal computer
When the connection between the instrument and the diagnosis socket has been establish, the instrument displays the available
applications.
Select the application on the numerical keyboard (0 9) and confirm with .

PT - BOX
PT - BOX is a test tool to be connected to a Personal Computer .
Figure 103
120995
1. Data flow lamps (blinking) - 2. Ignition indicator - 3. USB indicator - 4. Operation indicator -
5. Serial port indicator - 6. Error indicator - 7. CAN line indicator -
8. Line K indicator for automatic management
With the PT-BOX you can perform:

- Basic testing: central unit ID reading, failure memory reading, parameter reading, failure memory clearing and Flight Recorder
memory reading;
- Active testing: main component testing (actuators, contactors, etc..);
- Flight Recorder reading;
- ECU acknowledgement of replaced electronic components;
- 2nd level and PTO programming;
- Parameter acquisition during operation tests.

FAULT CODES
Failure code Failure description
Vehicle 1 ((Sensors / Consistency tests)
1.1.2 ACCELERATOR PEDAL
1.1.9 PLAUSIBILITY +15
1.1.A PLAUSIBILITY +50
Vehicle 2 (Indicator lamps / Relais / Actuators)
1.2.3 EDC LAMP
1.2.5 MAIN RELAY DEFECT
1.2.6 BATTERY VOLTAGE
1.2.8 MAIN RELAY - SHORT CIRCUIT TO BATTERY
1.2.9 AIR-CONDITIONER COMPRESSOR RELAY
1.2.B THERMOSTARTER RELAY 1 (HEATER)
1.2.E MANAGEMENT SYSTEM PRE/POST-HEATING (ACTIVE)
2.2.5 INTERRUPTED AFTER-RUN
2.2.8 MAIN RELAY - SHORT CIRCUIT TO GROUND
Engine 1 (Temperature and pressure sensors)
1.3.1 COOLANT TEMPERATURE SENSOR
1.3.2 COOLANT TEMPERATURE SENSOR (TEST)
1.3.3 AIR TEMPERATURE SENSOR BOOST AIR
1.3.4 BOOST PRESSURE SENSOR
1.3.5 FUEL TEMPERATURE SENSOR
1.3.6 RAIL PRESSURE SENSOR OR SIGNAL ERROR
1.3.7 DBV VALVE MANAGEMENT (BOOST PRESSURE)
1.3.8 OIL PRESSURE SENSOR
1.3.A OIL TEMPERATURE SENSOR
2.3.2 COOLANT TEMPERATURE SENSOR ABSOLUTE TEST
2.3.6 RAIL PRESSURE SENSOR OFFSET
2.3.8 OIL LOW PRESSURE
2.3.A OIL TEMPERATURE ABOVE NORMAL
Engine 2 (Speed sensors/actuators)
1.4.1 CRANKSHAFT SPEED
1.4.2 ENGINE WORKING ONLY WITH CAMSHAFT SENSOR
1.4.3 CAMSHAFT SENSOR
1.4.4 FAULT BETWEEN FLYWHEEL SENSOR AND CAMSHAFT
Damage information
1.4.D ENGINE OVERSPEED
1.5.B HIGH PRESSURE TEST (DEACTIVATES RAIL PRESS.MONITORING)
1.9.D INDICATES TORQUE LIMITATION DUE TO PERFORMANCE LIMITER
4.9.E INDICATES THE TORQUE LIMITATION DUE TO ENGINE PROTECTION
6.9.E INDICATES TORQUE LIMITATION DUE TO FUEL QUANTITY LIMITATION


Fuel metering
1.5.1 HIGH PRESSURE SYSTEM
1.5.2 FAULT ON THE FUEL PRESSURE CONTROL OF THE RAIL (POSITIVE DEVIATION)
1.5.3 FAULT ON THE FUEL PRESSURE CONTROL OF THE RAIL (NEGATIVE DEVIATION)
1.5.4 RAIL PRESSURE ERROR: TOO LOW
1.5.5 RAIL PRESSURE ERROR: TOO HIGH
1.5.7 ERROR ON THE RAIL PRESSURE (EXCESSIVE DUTY CYCLE)
1.5.9 PRESSURE MPROP REGULATOR ERROR
2.5.9 PRESSURE MPROP REGULATOR ERROR (SHORT CIRCUIT TO POSITIVE)
3.5.9 SHORT CIRCUIT TO GROUND OF METERING UNIT OUTPUT
Injectors 1
1.6.1 INJECTOR CYLINDER 1 / SHORT CIRCUIT
1.6.7 INJECTOR CYLINDER 1 / OPEN CIRCUIT
1.6.A INJECTOR CYLINDER 4 / OPEN CIRCUIT
1.6.B INJECTOR CYLINDER 5 / OPEN CIRCUIT
1.6.C INJECTOR CYLINDER 6 / OPEN CIRCUIT
1.6.E THE MINIMUM NUMBER OF INJECTIONS WAS NOT REACHED: STOP THE ENGINE
Injectors 2
1.7.1 BENCH 1 CC
1.7.3 BENCH 2 CC
1.7.C BENCH 1 INJECTORS CHECK (INTERNAL ECU)
2.7.C BENCH 2 INJECTORS CHECK (INTERNAL ECU)
Boosting system and turbine speed
1.9.E TORQUE REDUCTION DUE TO SMOKE LIMITATION
Interfaces 1 (CAN-Bus)
1.B.1 ERROR ON CAN CONTROLLER A
1.B.3 ERROR ON CAN CONTROLLER C
1.B.4 TIMEOUT CAN MESSAGE BC2EDC1
1.B.5 TIMEOUT CAN MESSAGE VM2EDC
1.B.D TIMEOUT CAN MESSAGE CCVS
2.B.4 TIMEOUT CAN MESSAGE BC2EDC2
Interfaces 2 (CAN line timeout messages)
1.C.6 ERROR MESSAGE CAN TSC1-PE


1.C.8 ERROR MESSAGE CAN TSC1-VE
1.C.9 ERROR MESSAGE CAN TF
2.C.6 TIMEOUT OF CAN MESSAGE TSC1-PE PASSIVE
3.C.8 TIMEOUT OF CAN MESSAGE TSC1-VE PASSIVE
ECU 1 (internal checks)
1.D.1 ECU OVERRUN MONITORING ERROR
1.D.6 ECU INTERNAL ERROR (TPU)
1.D.7 INTERNAL ECU ERROR (VARIANT AREA)
3.D.3 ERRORE INTERNO CENTRALINA
ECU 2 (Power supply / Immobilizer / Runaway / Sensor power supply)
1.E.1 ECU: SHORT CIRCUIT OR OPEN CIRCUIT
1.E.3 ERROR FOR ECU INTERNAL MONITORING
1.E.4 ERROR FOR ECU INTERNAL MONITORING
1.E.5 SENSORS POWER SUPPLY FAULT (12V)
1.E.6 SENSOR POWER SUPPLY 1
1.E.9 ECU OVERRUN MONITORING ERROR
1.E.A ECU OVERRUN MONITORING ERROR
1.E.B ATMOSPHERIC PRESSURE SENSOR
2.E.1 SHORT CIRCUIT TO BATT OR GROUND, NO LOAD, EXCESS.TEMP. FOR LOW SIDE POWER STAGE

PART FOUR -
MAINTENANCE PLANNING


Recovery
To ensure optimised working conditions, in the following pages we are providing instructions for the overhaul control
interventions, checks and setting operations that must be performed on the engine at due planned dates.
The frequency of the maintenance operations is just an indication since the use of the engine is the main characteristic to
determine and evaluate replacements and checks.
It is not only allowed but recommended that the staff in charge of the maintenance should also carry out the necessary
maintenance and controlling operations even if not being included in the ones listed here below but that may be suggested by
common sense and by the specific conditions in which the engine is run.
Planning of controls and periodical intervention
Every Every Every Every

Type of operation 150 hours 300 hours 600 hours 1200 hours
Engine
Engine oil topping up
Change engine oil
Change engine oil filters
Change of blow-by filter
Replacing fuel filter
Adjustment of valve clearance
Change miscellaneous drive belts
Chassis and mechanical assemblies
Change fuel pre-filter (if available)
NOTE The maintenance operations are valid only if the setter fully complies with all the installation prescriptions provided
by Iveco Motors.

NOTE The engine lubrication intervals apply with the use of Diesel fuel with sulphur content of less than 0.5%.
If using diesel with a percentage of sulphur above 0.5%, the oil-change frequency has to be halved.
Use engine oil: ACEA E3 - 96
NOTE Diesel fuel for low temperatures. Standard EN590 defines different classes of Diesel fuels, identifying the characteristics
of those most suitable for use in low ambient temperatures.
Compliance with the regulations regarding the distribution of fuels suitable for the climatic and geographic conditions
of the various countries is entirely up to the oil companies.
- The engine oil and filters must be changed every 12 months in case of very low annual use or less than 600 hours.
- Premature clogging of the air cleaner is generally due to the operating conditions. The filter should therefore be
renewed whenever clogging is signalled by the sensor regardless of the prescribed time interval, which should in
any case be respected in the absence of any specific indications.
The time intervals given in this plan are merely approximate as they refer to using the engines in an industrial
environment with average use in relation to displacement.

OFF-PLANE OPERATIONS
Every year Before winter

and possibly when a maintenance operation is carried out
Check the antifreeze percentage in the engine cooling water
Every two year

Change engine coolant
NOTE Early air filter clogging is usually due to environmental conditions. For this reason, the filter should be changed if clogging
is signalled by the related sensor, regardless of the prescriptions that shall be observed if no specific indications have
been provided.

MAINTENANCE PROCEDURES Top up via the tappet cover cap (2). When filling, remove the
Checks and controls dipstick (1) to facilitate the flow of oil.
Engine oil level check
The check must be executed when the engine is
disconnected and possibly cool.
The engine oil is highly polluting and harmful.
The check can be made using the specially provided flexible
rod (1). In case of contact with the skin, rinse well with water
and detergent.
Figure 104 (Demonstration)
Adequately protect the skin and the eyes, operate
in full compliance with safety regulations.
Disposal must be carried out properly, and in full
compliance with the law and regulations in force.
Lubricating system check

The check must be executed both when the engine
disconnected and when it is running.
Verify the presence of any oil leakage or blow-by from the

head, from the engine pan of from the heat exchanger.
145841

Draw off the rod from its slot and check that the level is In case of contact with the skin, rinse well with water
within the etched tags of minimum and maximum level. and detergent.
Whether it should be difficult to make the evaluation, Adequately protect the skin and the eyes, operate
proceed cleaning the rod using a clean cloth with no rag in full compliance with safety regulations.
grinding and put it back in its slot. Draw it off again and check
the level. Disposal must be carried out properly, and in full
In case the level results being close to the tag showing
minimum level, provide filling lubrication of the engines
components.
145842

Engine oil change - Check the level through the dipsick until when the filling
is next to the maximum level notch indicated on the dip-
Figure 106 sick.
Engine oil filter change

Figure 107
119975
We recommend to carry out the oil drainage when the

motor is hot.
Warning: We recommend to wear proper protec-
tions because of high motor service temperature. 119976
The motor oil reaches very high temperature: you

must always wear protection gloves. Drain the oil as described in the section Changing the engine
oil.
- Place a proper container for the oil collecting under the
pan connected with the drain plug (3).
- Unscrew the plug (3) and then take out the control dip- NOTE Warning: the oil filter contains inside a quantity of
sick (1) and the inserting plug (2) to ease the downflow oil of about 1 kg.
of the lubrication oil.
Place properly a container for the liquid.
Warning: avoid the contact of skin with the motor
oil: in case of contact wash the skin with running
water.
The oil motor is very pollutant and harmful.
The motor oil is very pollutant: it must be disposed
In case of contact with the skin, wash with much of according to the rules.
water and detergent.
Protect properly skin and eyes: operate according to
safety rules.
Dispose of the residual properly following the rules.
NOTE Before refitting the new cartridge, wet seal using
engine oil.
- After draining completely, screw on the plug (3) under Screw the oil filter (1) by hand until it touches the support,
the sump and tighten it to the prescribed torque. then tighten of a turn to the required torque.
- Add the specified quantity of recommended engine oil Refit the plug under the sump, tightening it to the required
through the filler (2) of the tappets cover. torque.
Add the required amount of recommended engine oil
through the filler.
Complete the operation as described in the section
NOTE Use only the recommended oil or oil having the re- Changing the engine oil.
quested features for the corrrect motor function-
ing.
In case of topping up, dont mix oils having different
features.
If you dont comply with theses rules, the service
warranty is no more valid.

Changing the Blow-by filter Fuel filter change
Figure 108 Figure 110
145886
114018
Unlock screws (2) and remove cover (1). Remove the

centrifugal filter (3) underneath and replace it. During this operation dont smoke and dont use free
flames.
Avoid to breathe the vapors coming from filter.
Figure 109
After filters replacement the supply equipment
! deaeration must be carried out.
Unscrew the fuel filter cartridge (2).

Before fitting the new cartridge, wet seal with fuel oil or
engine oil.
Lock the new one by hand and carefully check that rubber
seal and contact surface are clean and in perfect conditions.
Lock cartridge by hand till contact with support and then lock
it for of a rev. at prescribed tightening torque.
When replacing the filter cartridge (2) do NOT fill

! it.
This operation is banned to avoid impurities
entering into the circuit, which would damage the
injector/pump system components.
Bleed air from the fuel as described below.
Fuel bleeding
Loosen the bleed screw (1) connecting the drainage by a
117692
transparent flexible hose to a suitable container.
at required torque.
Install cover (3) and lock screws (4) at required torque.

Figure 111 Use appropriate equipment (5) on the belt tensioner (6)
in the direction shown by the arrow and extract the belt
(4) from the pulleys of the alternator (1), of the coolant
pump (2) and from the idler pulleys (3).
- Replace the worn belt with a new one.
- Place the belt on the pulleys and the guide rollers.
- Place the automatic tightener in order to key the belt in
the functioning position.
- Further adjustments are not required.
145887 Replacing coolant

Only proceed with the engine stopped and at a low
With the hand pump (2) of the fuel pre-filter (1) pump until
temperature, so as to avoid the risk of burning.
fuel completely free of air bubbles flows from the bleed
screw. - Provide suitable containers to ensure that no coolant is
dispersed into the environment.
After the operation, tighten the bleed screw.
- Loosen the seal elements, remove the sleeves
Start the engine and allow it to run at minimum for a few
connecting the engine circuit to the heat exchanger and
minutes to expel any remaining air.
wait until it has emptied completely. When empty, repair
the circuit making sure that the sleeves are perfectly
Valve lash check a adjustment sealed.
For correct operation, follow instructions contained in
related chapter in section 3 Industrial Application. - Fill up the circuit.
- Refill the engine and the heat exchanger until complete
top up.
Check of water pump/alternator control belt condition
- With the filler cap open, start the engine and keep it
Figure 112 idling for nearly one minute. This phase facilitates the
cooling liquid air bleed.
- Stop the engine and top up again.
145888
Visually check that belt (4) is not worn out or broken; change
it as described below, if required.
NOTE To be able to work on the engine belt you first

need to remove the protective casing (if
applicable) by unscrewing the screws.


F2C CURSOR ENGINES SECTION 4 - OVERHAUL AND TECHNICAL SPECIFICATIONS 1
SECTION 4
Overhaul and technical specifications
Page
GENERAL CHARACTERISTICS . . . . . . . . . . . . . 3
ASSEMBLY CLEARANCE DATA . . . . . . . . . . . . 5
ENGINE OVERHAUL . . . . . . . . . . . . . . . . . . . . . 11
ENGINE REMOVAL AT THE BENCH . . . . . . . . 11
REPAIR OPERATIONS . . . . . . . . . . . . . . . . . . . . 12
CYLINDER BLOCK . . . . . . . . . . . . . . . . . . . . . . . 12
- Checks and measurements . . . . . . . . . . . . . . . 12
CYLINDER LINERS . . . . . . . . . . . . . . . . . . . . . . . 13
- Replacing cylinder liners . . . . . . . . . . . . . . . . . 15
CRANKSHAFT . . . . . . . . . . . . . . . . . . . . . . . . . . 16
- Measuring main journals and crank pins . . . . . 17
PRELIMINARY MEASUREMENT OF MAIN AND BIG

END BEARING SHELL SELECTION DATA . 18
- Selecting the main and big end bearing shells . 19
- Replacing the timing control gear and the

oil pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
- Checking main journal installation clearance . . 25
- Checking crankshaft end float . . . . . . . . . . . . . 26
PISTON-CONNECTING ROD ASSEMBLY . . . . 27
- Removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
- Conditions for correct gudgeon pin-piston

coupling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
- Piston rings . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

2 SECTION 4 - OVERHAUL AND TECHNICAL SPECIFICATIONS F2C CURSOR ENGINES
Page
Page
CONNECTING ROD . . . . . . . . . . . . . . . . . . . . . 30
TIMING GEAR . . . . . . . . . . . . . . . . . . . . . . . . . . 39
- Mounting the connecting rod - piston assembly 32
- Camshaft drive . . . . . . . . . . . . . . . . . . . . . . . . . 39
- Mounting the piston rings . . . . . . . . . . . . . . . . 32
- Intermediate gear pin . . . . . . . . . . . . . . . . . . . . 39
- Fitting the connecting rod-piston assembly into the
piston liners . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 - Idler gear . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
- Twin idler gear . . . . . . . . . . . . . . . . . . . . . . . . . 39

- Piston protrusion check . . . . . . . . . . . . . . . . . . 33
- Replacing the bushings . . . . . . . . . . . . . . . . . . . 39
- Checking assembly clearance of big end pins . . 34
- Camshaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
CYLINDER HEAD . . . . . . . . . . . . . . . . . . . . . . . . 34
- Checking cam lift and pin alignment . . . . . . . . . 40
- Dismounting the valves . . . . . . . . . . . . . . . . . . 34
- Bushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
- Checking the planarity of the head on the
cylinder block . . . . . . . . . . . . . . . . . . . . . . . . . . 34 - Use beater 99360505 to change bushings . . . . 42
VALVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 VALVE SPRINGS . . . . . . . . . . . . . . . . . . . . . . . . . 42
- Removing deposits and checking the valves . . . 35 - Fitting the valves and oil seal ring . . . . . . . . . . . 42
VALVE GUIDES . . . . . . . . . . . . . . . . . . . . . . . . . . 35 ROCKER SHAFT . . . . . . . . . . . . . . . . . . . . . . . . . 43
- Replacing of valve guides . . . . . . . . . . . . . . . . . 36 - Shaft . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
- Replacing - Reaming the valve seats . . . . . . . . . 36 - Rocker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
REPLACING INJECTOR HOLDER CASES . . . . . 36 TIGHTENING TORQUES . . . . . . . . . . . . . . . . . 44

GENERAL CHARACTERISTICS
Type F2CE9687
Cycle 4-stroke Diesel engine

Fuel feed Turbocharged
Injection Direct
No. of cylinders 6 in line

Bore mm 117
Stroke mm 135
+ + +.. = Total displacement cm3 8710

Type F2CE9687
A
VALVE TIMING
opens before T.D.C. A 17
closes after B.D.C. B 31

B
opens before B.D.C. D 48
closes after T.D.C. C 9

D
For timing check
mm -
X
X mm -
Running
mm 0.35 to 0.45
X
mm 0.55 to 0.65
Bosch Common Rail with CRIN2 injectors and high pressure

FEED
pump CP3.3
Nozzle type DLLA 137
Injection order 1-4-2-6-3-5
bar
Injection pressure bar
1800
Injector calibration bar

ASSEMBLY CLEARANCE DATA
Type F2CE9687
CYLINDER BLOCK AND

mm
CRANKMECHANISM COMPONENTS
1
Bores for cylinder liners:
upper 130.500 to 130.525
1
lower 129.510 to 129.535
Cylinder liners:
external diameter:
upper 130.461 to 130.486
L 2
lower 129.475 to 129.500
2 226,15
length L
226.15
Cylinder liners -
crankcase bores
upper 0.014 to 0.064
lower 0.010 to 0.060
External diameter 2 -
Cylinder sleeve
3
inside diameter 3A* 117.000 to 117.012
X
inside diameter 3B* 117.010 to 117.022
Protrusion X 0.035 to 0.065

* Selection class
Pistons:
1 measuring dimension X 15
X external diameter 1A 116.894 to 116.906
external diameter 1B 116.904 to 116.916
2 pin bore 2 52.010 to 52.016
Piston - cylinder sleeve
A* 0.094 to 0.118
B* 0.094 to 0.118
* Selection class
Piston diameter 1 -
X
Pistons protrusion X 0.873 to 1.117
3 Gudgeon pin 3 51.994 to 52.000
Gudgeon pin - pin housing 0.010 to 0.022

F2CE9687
Type
mm
X1 3,120 3,140
X1
X2 3.120 to 3.140
X3 Piston ring grooves X2 2.550 to 2.570
X3 4.020 to 4.040
Piston rings:
trapezoidal
p seal S1 3.000
S1 lune seal S2 2.470 to 2.500
S2
S3 milled
ill d scraper ring
i
with slits and internal
spring S3 3.970 to 3.990
1 -
Piston rings - grooves 2 0.050 to 0.100
3 0.030 to 0.070
Piston rings -
X1 Piston ring end gap
in cylinder liners
X2
X1 0.3 to 0.4
X3
X2 0.60 to 0.75
X3 0.35 to 0.65
Small end bush housing

1 1 55.700 to 55.730
Big end bearing

housing 2 85.987 to 86.013
2
1 85.987 to 85.996
Selection classes { 2
3
85.997 to 86.005
86.006 to 86.013
4 Small end bush diameter
outside 4 55.780 to 55.820
3
inside 3 52.015 to 52.030
Big end bearing shell S
S Red 1.994 to 2.002
Green 2.002 to 2.010
Yellow D 2.010 to 2.018
Small end bush - housing 0.05 to 0.08
Piston pin - bush 0.015 to 0.036
Big end bearing 0.127 - 0.254 - 0.508

Connecting rod weight
g
A
A 3450 to 3470
Class B 3471 to 3490
C 3491 to 3510
D Fitted in production only and not supplied as spares

F2CE9687
Type
mm
X
Measuring dimension X 125
Max. connecting rod

axis misalignment
tolerance 0.08
Main journals 1
- nominal 92.970 to 93.000
- class 1 92.970 to 92.980
- class 2 92.980 to 92.990
1 2 - class 3 92.990 to 93.000
Crankpins 2
- nominal 81.915 to 81.945
- class 1 81.915 to 81.925
- class 2 81.925 to 81.935
- class 3 81.935 to 81.945
S1 S 2 Main bearing shells S1
Red 2.968 to 2.978
Green 2.978 to 2.988
Yellow* 2.988 to 2.998
Big end bearing shells S2
Red 1.994 to 2.002
Green 2.002 to 2.010
Yellow* 2.010 to 2.018
Main bearing housings 3
- nominal 99.000 to 99.030
3 - class 1 99.000 to 99.009
- class 2 99.010 to 99.019
- class 3 99.020 to 99.030
Bearing shells -
0.050 to 0.090
main journals
Bearing shells -
0.040 to 0.080
big ends
Main bearing shells 0.127 - 2.254 - 0.508
Big end bearing shells 0.127 - 2.254 - 0.508
Main journal,
thrust bearing X1 39.96 to 40.04
X1
Main bearing housing,

X2
X3
Thrust washer
halves X3 3.38 to 3.43
Crankshaft end float 0.10 to 0.30
1 2 Alignment 1-2 -
Ovalization 1-2 0.04
Taper 1-2 -
* Fitted in production only and not supplied as spares

Type F2CE9687
CYLINDER HEAD - VALVE TRAIN mm

1
Valve guide housings

in cylinder head
1 12.9800 to 12.997
Valve guide 2 8.023 to 8.038

3 13.012 to 13.025
3
Valve guides - housings

0.015 to 0.045
in the cylinder heads
Valve guide 0.2 - 0.4
4 Valves:
4 7 970 to 7.985
7.970 7 985
60 30 7 30
4 7.970
9 0 to 7.985
98
+15
+15
45 -0
-0

Valve stem and its guide 0.040 to 0.070
Valve seat in
head
1
41.985 to 42.020
1 1 40.985 to 41.020
Outside diameter of valve
2 seat; angle of valve seat
in cylinder head:
00
-0,5
0 5
2 42.060 to 42.075
60 - 30
0
-0,5
2 41.060
41 060 to
t 41.075
41 075
45 - 30
X 0.5 to 0.8
Recessing of valve
X X 1.6 to 1.9
Between valve
seat and head 0.040 to 0.090

Table 1
F2CE9687
Type
mm
Valve spring height:
A B
free height H 70.77 71.34
under a load of:
H H1 N 460 23 H1A {
H 2 N 460 22 H1B 51
N 740 33 H2A {
3 4 42
N 731,4 H2B
2 39
Injector protrusion X 1.2 to 1.5

X
Camshaft bushing housing

in the cylinder head:
17 69.000 to 69.030

2
Camshaft bearing
journals:
17 64.924 to 64.080
1 3
Outer diameter of
camshaft bushings:
69.090 to 69.130
Inner diameter of
camshaft bushings: 65.080 to 65.116
Bushings and housings

0.060 to 0.130
in the cylinder head
Bushings and bearing
journals 0.100 to 0.192
Cam lift:
H 7.4034
8.2108
1
Rocker shaft 1 31.964 to 31.980

F2CE9687
Type
mm
Bushing housing in
rocker arms
32.025 to 32.041
32.025 to 32.041
Between bushings and

housings
0.045 to 0.077
0.045 to 0.077
TURBOCHARGER
Type HX40
End float 0.025 to 0.127
Radial play 0.330 to 0.508

ENGINE OVERHAUL Figure 3

ENGINE REMOVAL AT THE BENCH
The following instructions are prescribed on the
understanding that the engine has previously been placed on
the rotating bench and that removal of all specific
components of the equipment have been already removed
as well. (See Section 3 of the manual herein).
The section illustrates therefore all the most important
engine overhaul procedures.
Figure 1
114615
Use adequate hexagonal spanner, unlock screws (1 and 3)

and remove stiffening plate (2) as well as main journals (4).
NOTE Note down the assembly position of the top and

bottom main bearing shells since, if reusing them, they
will need to be fitted in the position found upon
removal.
Figure 4
115881
Rotate the block (1) to the vertical position.
114035
Figure 2
Using tool 99360500 (1), remove the crankshaft (2).
Figure 5
115882 47571
Remove the main bearing shells (1), unscrew the screws and
Untighten screws (2) fixing the connecting rod cap (3) and take out the oil nozzles (2).
remove it. Remove the connecting rod-piston (1) assembly Remove the cylinder liners as described under the relevant
from the upper side. subheading on page 15.
Repeat these operations for the other pistons. After disassembling the engine, thoroughly clean
disassembled parts and check their integrity.
Keep the big end bearing shells in their respective
Instructions for main checks and measures are given
housings and/or note down their assembly position
in the following pages, in order to determine
since, if reusing them, they will need to be fitted in
whether the parts can be re-used.
the position found upon removal.

REPAIR OPERATIONS Figure 8

CYLINDER BLOCK
Checks and measurements
225036
34994
A = Selection class 117 117.012 mm
B = Selection class 117.010 117.022 mm
Internal diameter of the cylinder liners is checked for X = Selection class marking area
ovalization, taper and wear, using a bore dial (1) centesimal
gauge 99395687 (2) previously reset to ring gauge (3), In case of maximum wear >0.150 mm or maximum
diameter 117 mm. ovalization >0.100 mm compared to the values indicated in
the figure, the liners must be replaced as they cannot be
ground, lapped or trued.
NOTE If dia.117 mm ring gage is not available, use a NOTE Cylinder liners are equipped with spare parts with
micrometer. A selection class.
Figure 7 Figure 9
114035 114037
1 = 1st measuring A = 130.500 to 130.525 mm

2 = 2nd measuring B = 129.510 to 129.535 mm
3 = 3rd measuring C = 130.461 to 130.486
D = 129.475 to 129.500 mm
Carry out measurings on each cylinder liner at three different
The figure shows the outer diameters of the cylinder liners
levels and on two (A-B) surfaces, to one another
and the relative seat inner diameters.
perpendicular, as shown in Figure.
The cylinder liners can be extracted and installed several
times in different seats, if necessary.

CYLINDER LINERS
Figure 10
114038
CYLINDER BLOCK ASSEMBLY WITH CHROME-PLATED CYLINDER LINERS
Figure 11
145836
CYLINDER LINERS MAIN DATA
Selection class A mm 117.000 to 117.012

B mm 117.010 to 117.022

Figure 12
DETAIL A
145837
Figure 13
DETAIL B
145838

Replacing cylinder liners Figure 16

Removal
Figure 14
77812
Check cylinder barrel protrusion with tool 99360334

(1-2-3-4) and tighten screw (1) to 170 Nm.
47577
With dial gauge 99395603 (5) placed on base 99370415 (6)
measure the cylinder barrel protrusion compared to the
Place details 99360706 (1 and 2) and plate 99360724 (4) as cylinder head supporting plane, it must be 0,035 to 0,065 mm
shown in the figure, by making sure that the plate (4) is (Figure 17); otherwise replace the adjusting ring (1,
properly placed on the cylinder liners. Figure 15) fitted with spare parts having different thickness.
Tighten the screw nut (1) and remove the cylinder liner (3)
from the block.
Figure 17
Fitting and checking protrusion
Figure 15
114041
CYLINDER LINER PROTRUSION
16798
Always replace water sealing rings (3, 4 and 5).

Install the adjustment ring (1) on the cylinder liner (2);
lubricate lower part of liner and install it in the cylinder unit
using the proper tool.
NOTE The adjustment ring (1) is supplied as spare parts

in the following thicknesses: 0.08 mm - 0.10 mm - 35012
0.12 mm. When the installation is completed, block the cylinder liners
(1) to the block (2) with studs 99360703 (3).

CRANKSHAFT
Figure 19
Upper main journal half bearing
Lower main journal half bearings

144835
MAIN DATA FOR THE CRANK SHAFT PINS AND THE HALF BEARINGS
Check the condition of the journals and the big end pins; there must no be signs of scoring, ovalization or excessive wear.
The data given refer to the normal diameter of the pins.
Figure 20 Figure 21
114043 114044
X. Detail of main journals connections Y. Detail of crank pins connections

Measuring main journals and crank pins Figure 23

Before grinding the crank pins using a micrometer (1),
measure the main journals and the crank pins (2) and decide,
on the basis of the undersizing of the bearings, the final
diameter to which the pins are to be ground.
Figure 22
47536
MEASURING CRANK PINS

During grinding, pay attention to journal and crank pins values
47535
specified in figures 19 and 20.
MEASURING THE MAIN JOURNALS
NOTE It is advisable to enter the values found in a table NOTE All journals and crank pins must also be ground to
(Figure 24). the same undersizing class, in order to avoid any
alteration to shaft balance.
Figure 24
Fill in this table with the measurements of the main journals and the crank pins.
MAIN JOURNALS
MIN.
MAX.
MIN.
MAX.
CRANK PINS 114045

PRELIMINARY MEASUREMENT OF MAIN AND BIG END BEARING SHELL SELECTION DATA
For each of the journals of the crankshaft, it is necessary to carry out the following operations:
MAIN JOURNALS: CRANKPINS:

- Determine the class of diameter of the seat in the - Determine the class of diameter of the seat in the
crankcase. connecting rod.
- Determine the class of diameter of the main journal. - Determine the class of diameter of the crankpin.
- Select the class of the bearing shells to mount. - Select the class of the bearing shells to mount.
DEFINING THE CLASS OF DIAMETER OF THE SEATS FOR BEARING SHELLS ON THE CRANKCASE
On the front of the crankcase, two sets of numbers are marked in the position shown (Figure 25 at top).
- The first set of digits (four) is the coupling number of the crankcase with its base (Figure 25 at bottom).
- The following seven digits, taken singly, are the class of diameter of each of the seats referred to (Figure 25 at bottom).
- Each of these digits may be 1, 2 or 3.
Figure 25
CLASS MAIN BEARING HOUSING

NOMINAL DIAMETER
99.000 to 89.009
99.010 to 99.019
99.020 to 99.030
114046

Selecting the main and big end bearing shells

NOTE To obtain the required assembly clearances, the main and big end bearing shells need to be selected as described
hereunder.
This operation makes it possible to identify the most suitable bearing shells for each of the journals (the bearing shells, if necessary,
can have different classes from one journal to another).
Depending on the thickness, the bearing shells are selected The following tables give the specifications of the main and
in classes of tolerance marked by a coloured sign (red-green big end bearing shells available as spares in the standard sizes
red/black green/black). (STD) and in the permissible oversizes (+0.127, +0.254,
+0.508).
Figure 26
STD +0.127
red 1.994 to 2.002
red/black 2.057 to 2.065
green 2.002 to 2.010
green/black 2.065 to 2.073
yellow* 2.010 to 2.018
yellow/black* 2.073 to 2.081
STD +0.127
red 2.968 to 2.978
red/black 3.031 to 3.041
green 2.978 to 2.988
green/black 3.041 to 3.051
yellow* 2.988 to 2.998
yellow/black* 3.051 to 3061

DEFINING THE CLASS OF DIAMETER OF THE MAIN JOURNALS AND CRANKPINS (Journals with nominal diameter)
Main journals and crankpins: determining the class of diameter of the journals.
Three sets of numbers are marked on the crankshaft in the position shown by the arrow (Figure 27 at top):
- The first number, of five digits, is the part number of the shaft.
- Under this number, on the left, a set of six digits refers to the crankpins and is preceded by a single digit showing the status
of the journals (1 = STD, 2 = -0.127), the other six digits, taken singly, give the class of diameter of each of the crankpins
they refer to (Figure 27 at top).
- The set of seven digits, on the right, refers to the main journals and is preceded by a single digit: the single digit shows the
status of the journals (1 = STD, 2 = -0.127), the other seven digits, taken singly, give the class of diameter of each of the
main journals they refer to (Figure 27 at bottom).
Figure 27
CRANKPIN
CLASS
NOMINAL DIAMETER
81.915 to 81.925
81.925 to 81.935
81.935 to 81.945
CLASS MAIN JOURNALS

NOMINAL DIAMETER
92.970 to 92.980
92.980 to 92.990
92.990 to 93.000

Selection of main half-bearings (nominal diameter pins)
After detecting, for each journal, the necessary data on block and crankshaft, select the type of half-bearings to be used, in
compliance with the following table:
Figure 28
STD.
114048
1 2 3
green green yellow
1
green yellow yellow
red green green
2
green green yellow
red red green
3
red green green
114055

Selection of main half-bearings (rectified pins)

If the journals have been rectified, the procedure described cannot be applied.
In this case, make sure that the new diameter of the journals is as specified on the table and install the only half-bearing type
required for this undersizing.
Figure 29
red/black =
mm 3.031 to 3.041
green/black =
mm 3.041 to 3.051
-0.127
green/black =
mm 3.0513 to 3.061
1 2 3
92.843 green/black green/black yellow/black
1
92.853 green/black yellow/black yellow/black
92.853 red/black green/black green/black

2
92.863 red/black red/black green/black

3

SELECTING THE BIG END BEARING SHELLS Figure 30

(JOURNALS WITH NOMINAL DIAMETER)
There are 4 references on the connecting rod casing in the
positions illustrated:
1. Coloured mark for identifying the weight
2. Coloured mark for identifying the diameter grade
3. Positioning stud visible from the front of the engine
4. Progressive number for identifying the connecting rod
NOTE The identification colours of the marks are given in

the table on page 31.
The number, indicating the class of diameter of the bearing

shell seat may be 1, 2 o 3.
Determine the type of big end bearing to fit on each journal
by following the indications in the table (Figure 31).
47557
Figure 31
STD.
1 2 3
Class yellow blue
green
green green yellow

1
green yellow yellow
red green green
2
green green yellow
red red green
3
red green green

Selection of connecting rod half-bearings (rectified pins)

If pins have been rectified, the procedure described must be applied.
In this case, (for each undersizing) determine the tolerance field the new big end pins belong to, and install the half-bearings
identified according to the relative table.
Figure 32
red/black =
mm 2.057 to 2.065
green/black =
mm 2.065 to 2.073 -0.127
green/black =
mm 2.073 to 2.081
1 2 3
1
81.799 green/black yellow/black yellow/black

2
81.809 red/black red/black green/black

3

Replacing the timing control gear and the oil Figure 35

pump
Check that the teeth of the gears are not damaged or worn,
otherwise remove them using the appropriate extractor.
Figure 33
114034
Using the hoist and hook 99360500 (1) mount the driving
shaft (2).
144834
NOTE Before fitting the gear, spread Loctite type 603 on

approx. 5 mm wide band on crankshaft, at 30 mm
from contact surface.
After fitting the gear (1) on the crankshaft (2), heat it for
~15 minutes in an oven at temperature not higher than
180C.
Let them cool down after the installation.
Checking main journal installation clearance
Figure 34 Figure 36
114049 114050
Fit the oil jets (2) aligning the dowel with the opening (3) in Place bearing halves (1) on main journals (2).
the crankcase.
Check the installation clearance between the main journals
Position the half-bearings (1) and the thrust washers on the and the relative bearings as follows.
main journal supports as illustrated in Figure 19.

Figure 37 Figure 38
145839 114615
- Position the main journal caps (4) and fit the

strengthening plate (2) following the procedure
- Clean accurately the parts and remove any trace of oil; described:
- Fit caps (1), including the half bearings (2) on the relevant - Tighten the inner bolts and then the outer bolts by hand
supports. starting from main journal 7 and continuing until main
journal 1.
- Tightening the bolts using torque wrench always starting
from main journal 7 and continuing until main journal
1:
1st stage: 140 Nm
2nd stage 60+60
Checking crankshaft end float
Figure 39
47588
End float is checked by placing a magnetic dial gauge (1) on

the crankshaft (2), as shown in the figure.
If the value obtained is higher than specified, replace the rear
thrust half-bearings and repeat this check.

PISTON-CONNECTING ROD ASSEMBLY

Figure 40
47580
PISTON CONNECTING ROD ASSEMBLY

1. Connecting rod body - 2. Half bearings - 3. Connecting rod cap - 4. Cap fastening screws - 5. Split ring - 6. Scraper ring
with spiral spring - 7. Bevel cut sealing ring - 8. Trapezoidal sealing ring - 9. Piston pin - 10. Piston
Make sure the piston does show any trace of seizing, scoring, Pistons are equipped with three elastic rings: a sealing ring, a
cracking; replace as necessary. trapezoidal ring and a scraper ring.
Pistons are grouped into classes A and B for diameter.
Removal
Figure 41 Figure 42
126311 126312
Removal of the piston split rings (2) using the pliers 99360184 Remove the piston pin split rings (2) using the round tipped
(1). pliers (1).
Figure 43 Figure 44
49026 32618
Remove the piston pin (1). Measuring the gudgeon pin diameter (1) with a micrometer
(2).
If removal is difficult use the appropriate beater.
Conditions for correct gudgeon pin-piston

coupling
Figure 45
49026
Lubricate the pin (1) and the relevant housing on the piston
hubs with engine oil; piston must be inserted with a slight
finger pressure and it should not come out by gravity.

Figure 46
114053
MAIN DATA OF PISTON, SNAP RINGS AND PIN

X = 0,6 0,15 Figure 49
The dimension is measured on a of 113 mm
Piston rings
Figure 47
3513
The sealing ring (2) of the 1 cavity is trapezoidal. Clearance

X between the sealing ring and its housing is measured by
placing the piston (1) with its ring in the cylinder barrel (3),
so that the sealing ring is half-projected out of the cylinder
16552 barrel.
Check the thickness of the piston ring (2) using a micrometer
(1). Figure 50
Figure 48
36134
Check the opening between the ends of the sealing rings (1),
using a thickness gauge (2), entered in the cylinder barrel (3).
16552
Check the clearance between the sealing rings (2) and the If the distance between ends is lower or higher than the value
relative piston housings (1) using a thikness gauge (3). required, replace split rings.

CONNECTING ROD
When fitting the connecting rods, check that all of them are of same weight class and from the same supplier. The
connecting rod/cap is of torn type; before assembly verify that the connecting rod is not damaged. Each connecting
rod can assembled with the relative cap only. If the cap is assembled on the reverse side, the connecting rod must be
rejected.
Figure 51
114054
MAIN DATA - BUSH, CONNECTING ROD, PIN AND HALF-BEARINGS

* Values to be obtained after installing the bush
1 Between the connecting rod bush and the connecting rod profile there must be a distance > 0.4 mm.
2 On the external breaking line, gap area allowed must be < 5 mm2.
3 No cracks are allowed in the threaded area.

Figure 52
115884
1. Coloured mark for identifying weight - 2. Coloured mark for identifying diameter grade - 3. Positioning stud visible from
the front of the engine - 4. Progressive number for identifying connecting rod
WEIGHT DIAMETER
85.987-85.996 Yellow
GRADE A 3450 g - 3470 g 85.997-86.005 Green
Yellow
86.006-86.013 Blue
85.987-85.996 Yellow
GRADE B 3471 g - 3490 g 85.997-86.005 Green
Green
86.006-86.013 Blue
85.987-85.996 Yellow
GRADE C 3491 g - 3510 g 85.997-86.005 Green
Blue
86.006-86.013 Blue

Mounting the connecting rod - piston assembly

Carry out the steps for removal described on pages 27 and
28 in reverse order.
Figure 53
117694
NOTE The connecting rod screws can be reused as long

as the diameter of the thread is not less than 11.4
mm.
Mounting the piston rings

Figure 54
49029
To fit the piston rings (1) on the piston (2) use the pliers
99360184 (3).
The rings need to be mounted with the word TOP (4)
facing upwards. Direct the ring openings so they are
staggered 120 apart.

Fitting the connecting rod-piston assembly Figure 56

into the piston liners
Figure 55
115885
47593
Fit the half-bearings (1), selected as described on pages 19
to 24, both on the connecting rod and on the stand. - all pistons belong to the same class, A or B;
- ideogram stamped on the piston crown is placed toward
the engine flywheel, or the cavity, on the piston cover,
If the cap (1) is fitted upsidedown, the connecting
corresponds to the position of the oil spray nozzles.
rod should be discarded.
NOTE As spares, class A pistons are provided and can be Piston protrusion check
fitted also to cylinder barrels belonging to class B. Once assembly is complete, check piston protrusion from
cylinder barrels: it must be 0.873 to 1.177 mm.
Fit the connecting rod-piston assemblies (1) into the piston
liners (2) using band 99360605 (1, Figure 56). Check the
following:
- the openings of the split rings are offset by 120;
Figure 57
1 Connecting rod-piston assembly
2 Marking area on the piston crown of ideogram

specifying the assembly position and the
selection class
3 Connecting rod marking area (see Figure 52).
61831

Checking assembly clearance of big end pins Figure 59
To check the clearance proceed as follows:

connect the connecting rods to the relative main journals,
place a length of calibrated wire on the latter.
Figure 58
47583
Install and fix tool 99360264 (2) with bracket (4); tighten by
lever (1) until cotters are removed (3); remove the tool (2)
and the upper plate (5), the spring (6) and the lower plate (7).
Repeat the operation on all the valves.
115886 Turn the cylinder head upside down and remove the valves
Install the connecting rod caps (1) with half-bearings; tighten (8).
the connecting rod cap fixing screws (2) to 50 Nm (5 kgm)
torque. By tool 99395216 (3), tighten the screws further at
90 angle.
Remove the caps and check the clearance by comparing the
width of the calibrated wire with the scale calibration on the
envelope containing the wire.
CYLINDER HEAD Checking the planarity of the head on the

Before dismounting cylinder head, check cylinder head for cylinder block
hydraulic seal by proper tooling; in case of leaks not caused
by cup plugs or threaded plugs, replace cylinder head. Figure 60 (Demonstration)
NOTE In case of plugs dismounting/replacement, on

mounting, apply sealant Loctite 270 on plugs.
36159
Dismounting the valves The planarity (1) is checked using a ruler (2) and a thikness
gauge (3). If deformations exist, surface the head using proper
NOTE Before dismounting cylinder head valves, number surface grinder; the maximum amount of material to be
them in view of their remounting in the position removed is 0.2 mm.
observed on dismounting should they not have to
be overhauled or replaced.
Intake valves are different form exhaust valves in
that they have a notch placed at valve head centre. NOTE After leveling, make sure that valve sinking and
injector protrusion are as described in the relative
paragraph.

VALVE Figure 62
Removing deposits and checking the valves
Figure 61
92841
MAIN DATA - VALVES AND VALVE GUIDES

48625
* Values to be obtained after installing the valve guides
Remove carbon deposits using the metal brush supplied.
Check that the valves show no signs of seizure or cracking. Check, by means of a micrometer, that valve stem diameters
Check the diameter of the valve stem using a micrometer are as specified; if necessary, grind the valves seat with a
(see Figure 62) and replace if necessary. grinder, removing the minimum quantity of material.
VALVE GUIDES
Figure 63
47509
INSTALLATION DIAGRAM FOR VALVE GUIDES AND VALVES
* Values to be obtained after installing the guide valves

Replacing of valve guides REPLACING INJECTOR HOLDER CASES

Remove valve guides by means of tool 99360288. Removal
Install by means of tool 99360288 equipped with part
99360294, which determines the exact installation position Figure 65
of valve guides into the cylinder heads; if they are not
available, install the valve guides in the cylinder head so that
they project out by mm 16.3 to 16.7 (Figure 63).
After installing the valve guides, smooth their holes with
sleeker 99390310.
Replacing - Reaming the valve seats

To replace the valve seats, remove them using the
appropriate tool.
Figure 64
41032 115887
Ream the valve seats (2) on cylinder head using tool (1). To replace the injector case (2), act as follows:
- thread the case (2) with tool 99390804 (1).
Carry out operations described in the following figs. by
fixing tools to the cylinder head by means of braket A.
NOTE Valve seats must be reamed whenever valves or
valve guides are replaced or ground.
After reaming the valve seats, use tool 99370415, to make

sure that the valve position, with respect to the cylinder head
surface, is the following:
- -0.5 to -0.8 mm (recessing) of exhaust valves;
- -1.6 to 1.9 mm (recessing) of discharge valves.

Figure 66 Figure 68
115889
- Lubricate sealing rings (3) and fit them to the case (4);
fix tool 99360554 (2) to the cylinder head by means of
115888
bracket A, install the new case, tighten the screw (1),
upsetting the case lower part.
- fasten extractor 99342149 (2) to case (3), by tightening
the nut (1), and pull out the case from cylinder head.
Figure 69
Figure 67
45633
115890
- Remove any residue (1), with tool 99390772 (2), from
the cylinder head groove. - Adjust the casing hole (3) with borer 99394043 (1) and
guide bushing 99394045 (2).
Figure 70 Figure 72
115891 114056
- Through miller 99394044 (1) and bushing 99394045 (2), INSTALLATION DIAGRAM FOR
ream the injector seat in the case (3), check the injector INJECTOR CASE
protrusion from the cylinder head plane which must be
1.2 to 1.5 mm.
Checking protrusion of injectors

Figure 71
47585
Using dial gauge (1), check the protrusion of the injector (2)
which must be 1.2 to 1.5 mm.

TIMING GEAR Idler gear

Camshaft drive
Figure 73 Figure 75
114210 114211
TIMING CONTROL COMPONENT PARTS

1. Camshaft - 2. Bushing - 3. Pin - 4. Articulated rod -
5. Camshaft control gear - 6. Idler gear - 7. Twin idler gear
- 8. Drive shaft driving gear.
Intermediate gear pin Twin idler gear
Figure 74 Figure 76
86926 114212
Rated assembling play between idler gear bushings and pins: Replacing the bushings
0.040 0.080 mm.
Bushings (1, Figures 75-76) can be replaced when they are
worn. Put up the bushing, then grind it so as to bring it to a
dimension of 65.010 0.10 mm.
NOTE Bushing fitting in gears (2, Figures 75-76) must be

performed in arrow direction, placing them as
shown in figures.

Camshaft
Checking cam lift and pin alignment
Figure 77
47506
Place the camshaft (4) on the tailstock (1) and check cam lift (3) using a centesimal gauge (2); values are shown in table on page 9.
Figure 78
47507
When the camshaft (4) is on the tailstock (1), check alignment of supporting pin (3) using a centesimal gauge (2); it must not exceed
0.030 mm.
If misalignment exceeds this value, replace the shaft.
Figure 79
1
47505
In order to check installation clearance, measure bush inner diameter and camshaft pin (1) diameter; the real clearance is obtained
by their difference.
If clearance exceeds 0.150 mm, replace bushes and, if necessary, the camshaft.

Figure 80
114213
MAIN DATA - CAMSHAFT AND TOLERANCES

The surfaces of shaft supporting pin and cams must be extremely smooth; if you see any sign of seizing or scoring, replace the
shaft and the relative bushes.
TOLERANCES TOLERANCE CHARACTERISTIC SYMBOL

ORIENTATION Perpendicularity
POSITION Concentricity or coaxial alignment
OSCILLATION Circular oscillation
IMPORTANCE CLASS ASSIGNED TO PRODUCT CHARACTERISTICS SYMBOL
CRITICAL
IMPORTANT
SECONDARY
Bushes
Figure 81
114214
MAIN DATA - CAMSHAFT BUSHES AND RELATIVE BLOCK SEATS
* Bush inner diameter after installation
The bush surfaces must not show any sign of seizing or Measure the bush inner diameters with a baremeter and replace
scoring; if they do replace them. them, if the value measured exceeds the tolerance value.
To take down and fit back the bushes, use the proper tool
99360487.
Use beater 99360505 to change bushings Fitting the valves and oil seal ring
Removal
Figure 84
Figure 82
114280
Use tool 99360505 (3) fitted as shown in fig. to remove

bushings (2).
Accurately position beater during removal phase.
Fitting
For fitting, reverse operations performed for
removal, with care to make lube hole (1), drilled on
bushing, coincide with corresponding hole in housing.
87051
Lubricate the valve stem and insert the valves in the
respective valve guides; fit the lower caps (1). Use tool
VALVE SPRINGS 99360292 to fit the oil seal (2) on the valve guides (3) of the
exhaust valves; then, to fit the valves, proceed as follows.
Figure 83
Valve closed
NOTE Should valves not have been overhauled or
replaced, remount them according to numbering
performed on dismounting.
Intake valves are different form exhaust valves in
that they have a notch placed at valve head centre.
Valve open
Figure 85
114215
MAIN DATA TO CONTROL EXHAUST AND

DISCHARGE VALVE SPRING
86290
- fit springs (6) and the upper plate (5);

- apply tool 99360264 (2) and block it with bracket (4);
tighten the lever (1) until cotters are installed (3),
remove tool (2).

ROCKER SHAFT
Figure 86
114216
The camshaft eccentric elements control the 12 valve rocker arms directly. Valve control rocker arms are fitted directly on rocker
arm shaft. Rocker arms slide directly on cam profiles by rollers. The other end operates on a crosspiece laid directly on the two
valve rods. A pad is placed between rocker arm adjustment screw and crosspiece. Two lube ducts are machined inside rocker
a rms. Rocker arms shaft runs through the cylinder head; it must be removed to reach all units below.
Shaft
Figure 87
114217
MAIN DATA OF THE ROCKER ARM SHAFT

Check that the surface of the shaft shows no scoring or signs of seizure; if it does, replace it.
Rocker
Figure 88
114219
DISCHARGE VALVE ROCKER

Figure 89
114218
EXHAUST VALVES ROCKER

The bush surfaces must not show any trace of scoring of excessive wear; otherwise, replace bushes or the whole rocker.

TIGHTENING TORQUES
PART TORQUE
Nm kgm
Pipe union for piston cooling nozzle M12x1.5 35 2 3.5 0.2
Heat exchanger retaining screws 63 7 6.3 0.7
Plug 125 15 12.5 1.5
Spacer and oil sump fastening screws
M10x1.5x45 41.5 3.5 4.1 0.3
Gearcase fastening screws to cylinder block:
M10x1.25 41.5 3.5 4.1 0.3
M12x1.75 63 7 6.3 0.7
M8x1.25 23.5 1.5 2.3 1.5
Cylinder head fastening screw
First stage pre-tightening 50 5
Second stage pre-tightening 100 10
Third stage angle closing 90
Fourth stage angle closing 75
Rocker arm shaft fastening screw M12x1.75x130 104.5 10.5 10.4 1
Locknut for rocker arm adjusting screw 39 5 3.9 5
Electroinjector retaining bracket screws
M10x1.5x40 39 43 3.9 4.3
Shoulder plate fastening screws to head 23.5 3.5 2.3 0.3
Engine support bracket fastening screws to cylinder head 74 8 7.4 0.8
Gear fastening screws to camshaft
First stage pre-tightening 25 2.5
Second stage pre-tightening 45
Phonic wheel fastening screws to distribution gear 8.5 1.5 0.8 0.1
Exhaust pipe fastening screws
pre-tightening 32.5 7.5 3.2 0.7
tightening 47.5 2.5 4.7 0.2
Connecting rod cap fastening screws: M12x1.25x69
Engine flywheel fastening screws M18x1.5x72
Flywheel pulley fastening screws to crankshaft
Main journal retaining screws M16x2x168
Second stage pre-tightening 60 + 60
Lubricate with oil MOLYKOTE before assembly
Lubricate with graphitized oil before assembly

PART TORQUE
Nm kgm
Damper flywheel fastening screws 115 15 11.5 1.5
Idler gear pin fastening screws
Second stage angle closing 90
Idle gear link rod fastening screw 24.5 2.5 2.4 0.2
Oil pump fastening screw 24.5 2.5 2.4 0.2
Oil pump suction rose fastening screw 24.5 2.5 2.4 0.2
Front cover fastening screw to cylinder block 19 3 1.9 0.3
Control unit fastening screw to cylinder block 19 3 1.9 0.3
Fuel filter support fastening screw to cylinder head 24.5 2.5 2.4 0.2
Screw securing the engine support to the wheelcase
Second stage angle closing 60
Turbo-compressor fastening screws and nuts
pre-tightening 35 5 3.5 0.5
tightening 46 2 4.6 0.2
Water pump fastening screw to cylinder block 24.5 2.5 2.4 0.2
Pulley fastening screw to hub 55 5 5.5 0.5
Rocker arm cover fastening screws 8.5 1.5 0.8 0.1
Thermostat box fastening screws to cylinder head 24.5 2.5 2.4 0.2
Automatic tightener fastening screws to cylinder block 45 5 4.5 0.5
Fixed tightener fastening screws to cylinder block 105 5 10.5 0.5
Fan support fastening screws to cylinder block 24.5 2.5 2.4 0.2
Starter fastening screws 44 4 4 0.4
Air heater on cylinder head 30 3 5 0.5
Hydraulic power steering pump gear fastening nut 105 5 10.5 0.5
Air conditioner compressor fastening screw to support 24.5 2.5 2.4 2.5
Alternator support superior fastening screw 71.5 4.5 7.1 0.4
Alternator bracket fastening screw to cylinder block 24.5 2.5 2.4 0.2
Water pipe unions 35 3.5
Water temperature sensor 32.5 2.5 3.2 0.2
Lubricate with oil MOLYKOTE before assembly
Lubricate with graphitized oil before assembly

PART TORQUE
Nm kgm
Flywheel rev sensor fastening screw 84 0.8 0.2
Camshaft rev sensor fastening screw 84 0.8 0.4
P.D.E solenoid connector fastening screw 1.62 0.3 0.1 0.3
Overboost pressure sensor fastening screw 82 0.8 0.2
Absolute pressure sensor fastening screw 22.5 2.5 2.2 0.2
P.W.M. control valve fastening screw/nut 82 0.8 0.2
Fuel/coolant temperature sensor 35 3.5
Coolant temperature indicator 23.5 2.5 2.3 0.2
Filter clogging sensor 10 1
Oil temperature switch 25 1 2.5 0.1
Oil pressure sensor 25 1 2.5 0.1
Electric wire fastening screw 82 0.8 0.2
Gear fastening screws to camshaft M14x2x50
First stage pre-tightening 40
Gear fastening screws to camshaft M14x2x50
150 184 15 18.4
Heater fastening screw M8 x 60 24.5 2.5 2.5 0.2
M8 x 90 24.5 2.5 2.5 0.2
Gear fastening screws to camshaft M10 x 1.25 x 20
46.5 52 4.65 5.2
Gear fastening screws to camshaft
46.5 52 4.65 5.2
Alternator positive retaining nut M8x1.25 12.5 2.5 1.3 0.3
Starter terminal nut 30 M10x1.5 21 3.4 2.1 0.3
Starter terminal nut 50 M5x0.8 3.6 1 0.4 0.1

F2C CURSOR ENGINES SECTION 5 - TOOLS 1
SECTION 5
Tools
Page
TOOLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
EQUIPMENT MODIFIED FOR ADAPTATION TO

CURSOR 9 ENGINE . . . . . . . . . . . . . . . . . . . 11

2 SECTION 5 - TOOLS F2C CURSOR ENGINES

TOOLS
TOOL NO. DESCRIPTION
99322230 Rotary telescopic stand
99331043 Adapter connectors 38 pin to 30 pin

(Part of 99368554)
99340051 Extractor for crankshaft front gasket
99340054 Extractor for crankshaft rear gasket
99342149 Extractor for injector-holder
99346245 Tool to install the crankshaft front gasket

TOOLS
99346260 Tool to install the crankshaft back gasket
Pliers for assembling and disassembling piston split rings

99360184 (105-106 mm)
99360264 Tool for assembly and disassembly engine valves
99360288 Box wrench for block junction bolts to the underblock
99360292 Box wrench for block junction bolts to the underblock
99360294 Tool to fit back valve guide

(to be used with 99360288)

TOOLS
Compression tool for checking the protrusion of cylinder liners

99360334
Cylinder liner compression plate

99360335 (to be used with 99360334)
Tool for rotating flywheel

99360341
99360500 Tool to lift crankshaft
99360505 Beater for tree removal and replacement bushings distribution
99360558 Tool for lifting and carrying shaft rockers

TOOLS
99360585 Swing hoist for engine disassembly assembly
Belt to insert piston in cylinder liner (60 - 125 mm)

99360605
99360612 Tool for positioning engine P.M.S.
99360613 Tool for timing of phonic wheel on timing gear
99360703 Tool to stop cylinder liners
99360706 Tool to extract cylinder liners

TOOLS
99360724 Ring (115 mm) (to be used with 99360706)
Rotary engine stand mounting bracket 99322230

99361042
99365054 Tool for injector holder heading
Series 8 keys to insert 14x18 (13-17-18-19-21-22-24-27-30 mm)

99368542
PT - Plus
99327210
30 to 19 pin adapter (component 99368554)

99368555

TOOLS
Adapter (5 m) for connection to PT01 testers diagnostic socket

99368556 30-pin (component 99368554)
Adapter (80 cm) for connection to PT01 testers diagnostic socket

99368558 30 poles Denox 2 (part of 99368554)
99370415 Base supporting the dial gauge for checking cylinder liner
protrusion (to be used with 99395603)
99389833 14x18 plug wrench (20-120 Nm)
Torque screwdriver for calibrating the injector solenoid valve

99389834 connector check nut
99390310 Valve guide sleeker

TOOLS
99390772 Tool for removing injector holding case deposits
99390804 Tool for threading injector holding cases to be extracted
Reamer to rectify injector holder lower side

99394043 (to be used with 99394014)
Reamer to rectify injector holder lower side

99394044 (to be used with 99394015)
Bushing (used with 99394043 and 99394044)

99394045
Measuring pair for angular tightening with 1/2

99395216 and 3/4 square couplings

TOOLS
Gauge for determining distance between tree distribution and high

99395221 pressure pump
Gauge for determining distance between camshaft and gear for

99395222 reference
99395223 Gauge for camshaft phasing
99395603 Dial gauge (0 - 5 mm)

EQUIPMENT MODIFIED FOR ADAPTATION TO CURSOR 9 ENGINE




F2C CURSOR ENGINES APPENDIX 1
Appendix
Page
SAFETY PRESCRIPTIONS . . . . . . . . . . . . . . . . . 3

2 APPENDIX F2C CURSOR ENGINES

F2C CURSOR ENGINES APPENDIX 3
SAFETY PRESCRIPTIONS - Do not execute any intervention if not provided with

Standard safety prescriptions necessary instructions.
Particular attention shall be drawn on some precautions that - Do not use any tool or equipment for any different
must be followed absolutely in a standard working area and operation from the ones theyve been designed and
whose non fulfillment will make any other measure useless provided for: serious injury may occur.
or not sufficient to ensure safety to the personnel in-charge
of maintenance. - In case of test or calibration operations requiring engine
Be informed and inform personnel as well of the laws in force running, ensure that the area is sufficiently aerated or
regulating safety, providing information documentation utilize specific vacuum equipment to eliminate exhaust
available for consultation. gas. Danger: poisoning and death.
- Keep working areas as clean as possible, ensuring
adequate aeration. During maintenance
- Ensure that working areas are provided with emergency
boxes, that must be clearly visible and always provided - Never open filler cap of cooling circuit when the engine
with adequate sanitary equipment. is hot. Operating pressure would provoke high
temperature with serious danger and risk of burn. Wait
- Provide for adequate fire extinguishing means, properly unit the temperature decreases under 50C.
indicated and always having free access. Their efficiency
must be checked on regular basis and the personnel - Never top up an overheated engine with cooler and
must be trained on intervention methods and priorities. utilize only appropriate liquids.
- Organize and displace specific exit points to evacuate - Always operate when the engine is turned off: whether
the areas in case of emergency, providing for adequate particular circumstances require maintenance
indications of the emergency exit lines. intervention on running engine, be aware of all risks
- Smoking in working areas subject to fire danger must be involved with such operation.
strictly prohibited. - Be equipped with adequate and safe containers for
- Provide Warnings throughout adequate boards signaling drainage operation of engine liquids and exhaust oil.
danger, prohibitions and indications to ensure easy
comprehension of the instructions even in case of - Keep the engine clean from oil tangles, diesel fuel and or
emergency. chemical solvents.
- Use of solvents or detergents during maintenance may
Prevention of injury originate toxic vapors. Always keep working areas
aerated. Whenever necessary wear safety mask.
- Do not wear unsuitable cloths for work, with fluttering
ends, nor jewels such as rings and chains when working - Do not leave rags impregnated with flammable
close to engines and equipment in motion. substances close to the engine.
- Wear safety gloves and goggles when performing the - Upon engine start after maintenance, undertake proper
following operations: preventing actions to stop air suction in case of runaway
- filling inhibitors or anti-frost speed rate.
- lubrication oil topping or replacement - Do not utilize fast screw-tightening tools.
- utilization of compressed air or liquids under pressure
(pressure allowed: 2 bar) - Never disconnect batteries when the engine is running.
- Wear safety helmet when working close to hanging - Disconnect batteries before any intervention on the
loads or equipment working at head height level. electrical system.
- Always wear safety shoes when and cloths adhering to - Disconnect batteries from system aboard to load them
the body, better if provided with elastics at the ends. with the battery loader.
- Use protection cream for hands. - After every intervention, verify that battery clamp
polarity is correct and that the clamps are tight and safe
- Change wet cloths as soon as possible from accidental short circuit and oxidation.
- In presence of current tension exceeding 48-60 V verify - Do not disconnect and connect electrical connections
efficiency of earth and mass electrical connections. in presence of electrical feed.
Ensure that hands and feet are dry and execute working
operations utilizing isolating foot-boards. Do not carry - Before proceeding with pipelines disassembly
out working operations if not trained for. (pneumatic, hydraulic, fuel pipes) verify presence of liquid
or air under pressure. Take all necessary precautions
- Do not smoke nor light up flames close to batteries and bleeding and draining residual pressure or closing dump
to any fuel material. valves. Always wear adequate safety mask or goggles.
- Put the dirty rags with oil, diesel fuel or solvents in Non fulfillment of these prescriptions may cause serious
anti-fire specially provided containers. injury and poisoning.

4 APPENDIX F2C CURSOR ENGINES
- Avoid incorrect tightening or out of couple. Danger: Respect of the Environment

incorrect tightening may seriously damage engines
components, affecting engines duration. - Respect of the Environment shall be of primary
importance: all necessary precautions to ensure
- Avoid priming from fuel tanks made out of copper alloys personnels safety and health shall be adopted.
and/or with ducts not being provided with filters.
- Be informed and inform the personnel as well of laws in
- Do not modify cable wires: their length shall not be force regulating use and exhaust of liquids and engine
changed. exhaust oil. Provide for adequate board indications and
- Do not connect any user to the engine electrical organize specific training courses to ensure that
equipment unless specifically approved by Iveco. personnel is fully aware of such law prescriptions and of
basic preventive safety measures.
- Do not modify fuel systems or hydraulic system unless
Iveco specific approval has been released. Any - Collect exhaust oils in adequate specially provided
unauthorized modification will compromise warranty containers with hermetic sealing ensuring that storage is
assistance and furthermore may affect engine correct made in specific, properly identified areas that shall be
working and duration. aerated, far from heat sources and not exposed to fire
danger.
For engines equipped with electronic gearbox:
- Handle the batteries with care, storing them in aerated
- Do not execute electric arc welding without having environment and within anti-acid containers. Warning:
priory removed electronic gearbox. battery exhalation represent serious danger of
- Remove electronic gearbox in case of any intervention intoxication and environment contamination.
requiring heating over 80C temperature.
- Do not paint the components and the electronic
connections.
- Do not vary or alter any data filed in the electronic
gearbox driving the engine. Any manipulation or
alteration of electronic components shall totally
compromise engine assistance warranty and
furthermore may affect engine correct working and
duration.

CURSOR ENGINES G-DRIVE 1
Part 2
G-DRIVE CURSOR ENGINES
Section
General specifications 1
G-Drive Application 2
PREFACE TO USERS GUIDELINE MANUAL
Section 1 describes engines F2C in their characteristics and ge-

neral operation.
Section 2 is specific of use.

2 CURSOR ENGINES G-DRIVE
NOTE Part no. 2 is characterized by describing a particular industrial/agricultural application: G-Drive motors.
These engines are marketed as an assembly that is also equipped with the air/coolant and possibly air/air (intercooler)
cooling device.
The description of this application gives the differences with the industrial application (given in the preceding Parts) and
reference must be made to it for all repair and maintenance work.

CURSOR ENGINES G-DRIVE 3
UPDATING
Section Description Page Date of revision

4 CURSOR ENGINES G-DRIVE

CURSOR ENGINES G-DRIVE SECTION 1 - GENERAL SPECIFICATIONS 1
SECTION 1
General specifications
Page
CORRESPONDENCE BETWEEN TECHNICAL

CODE AND COMMERCIAL CODE . . . . . . . . . 3
LUBRIFICATION . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
COOLING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
- Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
- Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
FUEL FEED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
TURBOCHARGING . . . . . . . . . . . . . . . . . . . . . . . . 7

2 SECTION 1 - GENERAL SPECIFICATIONS CURSOR ENGINES G-DRIVE

CORRESPONDENCE BETWEEN TECHNICAL CODE AND COMMERCIAL CODE
Technical Code Commercial Code

F2CE9685A*E001 CURSOR 87TE X

LUBRIFICATION
Engine lubrication is obtained with a gear pump driven by the crankshaft via gears.
A heat exchanger governs the temperature of the lubricating oil.
The oil filter, signalling sensors and safety valves are installed in the intercooler.
114244
Dropping oil
Pressure oil
LUBRICATION DIAGRAM

COOLING
Description
The engine cooling system is of the closed-circuit, forced circulation type.
It consists mainly of the following components:
- expansion tank,
- a heat exchanger to cool down lubrication oil;
- a water pump with centrifugal system incorporated in the cylinder block;
- fan;
- a 2-way thermostat controlling the coolant circulation.
Operation
The water pump is actuated by the crankshaft through a poli-V belt and sends coolant to the cylinder block, especially to the cylinder
head (bigger quantity). When the coolant temperature reaches and overcomes the operating temperature, the thermostat is
opened and from here the coolant flows into the radiator and is cooled down by the fan.
Figure 2
Water flowing out of the thermostat

Water circulating in the engine Water
flowing into the pump
119978
COOLING SYSTEM DIAGRAM

FUEL FEED
The Common Rail supply system is equipped with a special pump that maintains fuel at constant high pressure regardless from
phase and cylinder under injection and accumulated in an common duct shared by all electric injectors.
Therefore, fuel at injection pressure, calculated by ECU, is always available at electric injection inlet.
When the solenoid valve of an injector is energized by ECU, in related cylinder the injection of fuel taken directly from the
rail takes place.
Figure 3
Return
circuit
Supply
circuit
145840

TURBOCHARGING
The turbocharging system consists of:
- air filter;
- Turbocharger.
Figure 4
Exhaust
Inlet
Engine exhaust gas
Intake air
119980
SUPERCHARGING SYSTEM DIAGRAM


CURSOR ENGINES G-DRIVE SECTION 2 - G-DRIVE APPLICATION 1
SECTION 2
G-Drive application
Page
GENERAL CHARACTERISTICS . . . . . . . . . . . . . . . 3
ASSEMBLY CLEARANCE DATA . . . . . . . . . . . . . . 5
ENGINE CONNECTION AND DISCONNECTION

FROM THE RADIATOR . . . . . . . . . . . . . . . . . . 11
- Recovery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
- Inspection and/or maintenance interventions . 15
OPERATIONS OUTSIDE THE PLAN . . . . . . . . . . 16
MAINTENANCE PROCEDURES . . . . . . . . . . . . . . 17
- Checks and controls . . . . . . . . . . . . . . . . . . . . 17
PRINCIPLE ELECTRICAL DIAGRAM . . . . . . . . . . . 24
- Key to components . . . . . . . . . . . . . . . . . . . . . 25
- Function symbols for the control panel . . . . . . 25
ENGINE INTERFACE BOX . . . . . . . . . . . . . . . . . . 26
- Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
- Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
EDC 7 UC31 ELECTRONIC CONTROL UNIT . . 30
- EDC control unit PIN-OUT . . . . . . . . . . . . . . 31

2 SECTION 2 - G-DRIVE APPLICATION CURSOR ENGINES G-DRIVE

GENERAL CHARACTERISTICS
Type F2CE9685A*E001
Cycle Diesel 4 strokes

Feeding Turbocharged
Injection Direct
N. of cylinders 6 on-line

Diameter mm 117
Stroke mm 135
+ + +.. = Total displacement cm3 8710
Compression ratio 1:15.9 0.8
USA market
Maximum power
(prime) kW 251
Maximum power
(standby) kW 276
rpm 1800
SUPERCHARGING With intercooler
Turbocharger type HX 55
LUBRICATION Forced by gear pump, relief valve single action

oil filter
bar Oil pressure
(warm engine)
- idling bar -
- peak rpm bar -
COOLING Liquid
Water pump control Through belt
Thermostat
- start of opening C 85 1.5
NOTE Data, features and performances are valid only if the setter fully complies with all the installation prescriptions
provided by FPT.
Furthermore, the users assembled by the setter shall always be in conformance to couple, power and number of
turns based on which the engine has been designed.

Type F2C
A
VALVE TIMING
opens before T.D.C. A 17
closes after B.D.C. B 31

B
opens before B.D.C. D 48
closes after T.D.C. C 9

D
For timing check
mm -
X
X mm -
Running
mm 0.35 to 0.45
X
mm 0.55 to 0.65
Bosch Common Rail with CRIN2 injectors and high pressure

FEED
pump CP3.3
Nozzle type DLLA 137
Injection order 1-4-2-6-3-5
bar
Injection pressure bar
1800
Injector calibration bar

ASSEMBLY CLEARANCE DATA
Type F2C
CYLINDER BLOCK AND mm

CRANKMECHANISM COMPONENTS
1
Bores for cylinder liners:
upper 130.500 to 130.525
1
lower 129.510 to 129.535
Cylinder liners:
external diameter:
upper 130.461 to 130.486
L 2
lower 129.475 to 129.500
2 226,15
length L
226.15
Cylinder liners -
crankcase bores
upper 0.014 to 0.064
lower 0.010 to 0.060
External diameter 2 -
Cylinder sleeve
3
inside diameter 3A* 117.000 to 117.012
X
inside diameter 3B* 117.010 to 117.022
Protrusion X 0.035 to 0.065

* Selection class
Pistons:
1 measuring dimension X 15
X external diameter 1A 116.894 to 116.906
external diameter 1B 116.904 to 116.916
2
pin bore 2 52.010 to 52.016
Piston - cylinder sleeve
A* 0.094 to 0.118
B* 0.094 to 0.118
* Selection class
Piston diameter 1 -
X
Pistons protrusion X 0.873 to 1.117
3 Gudgeon pin 3 51.994 to 52.000
Gudgeon pin - pin housing 0.010 to 0.022

F2C
Type
mm
X1 3,120 3,140
X1
X2 3.120 to 3.140
X3 Piston ring grooves X2 2.550 to 2.570
X3 4.020 to 4.040
Piston rings:
trapezoidal
p seal S1 33.000
000
S 1 lune seal S2 2.470 to 2.500
S2
S3 milled
ill d scraper ring
i
with slits and internal
spring S3 3.970 to 3.990
1 -
Piston rings - grooves 2 0.050 to 0.100
3 0.030 to 0.070
Piston rings -
X1 Piston ring end gap
in cylinder liners
X2
X1 0.3 to 0.4
X3
X2 0.60 to 0.75
X3 0.35 to 0.65
Small end bush housing

1 1 55.700 to 55.730
Big end bearing

housing 2 85.987 to 86.013
2
1 85.987 to 85.996
Selection classes { 23 85.997 to 86.005
86.006 to 86.013
4 Small end bush diameter
outside 4 55.780 to 55.820
3
inside 3 52.015 to 52.030
Big end bearing shell S
S Red 1.994 to 2.002
Green 2.002 to 2.010
Yellow D 2.010 to 2.018
Small end bush - housing 0.05 to 0.08
Piston pin - bush 0.015 to 0.036
Big end bearing 0.127 - 0.254 - 0.508

Connecting rod weight
g
A
A 3450 to 3470
Class B 3471 to 3490
C 3491 to 3510
D Fitted in production only and not supplied as spares

F2C
Type
mm
X
Measuring dimension X 125
Max. connecting rod

axis misalignment
0.08
tolerance
Main journals 1
- nominal 92.970 to 93.000
- class 1 92.970 to 92.980
- class 2 92.980 to 92.990
1 2 - class 3 92.990 to 93.000
Crankpins 2
- nominal 81.915 to 81.945
- class 1 81.915 to 81.925
- class 2 81.925 to 81.935
- class 3 81.935 to 81.945
S1 S 2 Main bearing shells S1
Red 2.968 to 2.978
Green 2.978 to 2.988
Yellow* 2.988 to 2.998
Big end bearing shells S2
Red 1.994 to 2.002
Green 2.002 to 2.010
Yellow* 2.010 to 2.018
Main bearing housings 3
- nominal 99.000 to 99.030
3 - class 1 99.000 to 99.009
- class 2 99.010 to 99.019
- class 3 99.020 to 99.030
Bearing shells -
0.050 to 0.090
main journals
Bearing shells -
0.040 to 0.080
big ends
Main bearing shells 0.127 - 2.254 - 0.508
Big end bearing shells 0.127 - 2.254 - 0.508
Main journal,
X1
Main bearing housing,

X2
X3 Thrust washer
halves X3 3.38 to 3.43
Crankshaft end float 0.10 to 0.30
1 2 Alignment 1-2 -
Ovalization 1-2 0.04
Taper 1-2 -

Type F2C
CYLINDER HEAD - VALVE TRAIN mm

1
Valve guide housings

in cylinder head
1 12.9800 to 12.997
Valve guide 2 8.023 to 8.038

3 13.012 to 13.025
3
Valve guides - housings

0.015 to 0.045
in the cylinder heads
Valve guide 0.2 - 0.4
4 Valves:
4 7 970 to 7.985
7.970 7 985
60 30 7 30
4 7.970 to 7.985
+15
+15
45 -0
-0

Valve stem and its guide 0.040 to 0.070
Valve seat in
head
1 41.985 to 42.020
1 1 40.985 to 41.020
Outside diameter of valve
2 seat; angle of valve seat
in cylinder head:
0
-0,5
0 5
2 42.060 to 42.075
60 - 30
0
-0,5
2 41.060
41 060 to
t 41.075
41 075
45 - 30
X 0.5 to 0.8
Recessing of valve
X X 1.6 to 1.9
Between valve
seat and head 0.040 to 0.090

Table 2
F2C
Type
mm
Valve spring height:
A B
free height H 70.77 -
under a load of:
H H1 N 460 23 H1A {
H 2 N 460 22 H1B 51
N 740 33 H2A {
731 4 42
N 731,4 H2B 39
Injector protrusion X 1.2 to 1.5

X
Camshaft bushing housing

in the cylinder head:
17 69.000 to 69.030

2
Camshaft bearing
journals:
17 64.924 to 64.940
1 3
Outer diameter of
camshaft bushings:
69.090 to 69.130
Inner diameter of
camshaft bushings: 65.080 to 65.116
Bushings and housings

0.060 to 0.130
in the cylinder head
Bushings and bearing
journals 0.14 to 0.192
Cam lift:
H 7.5138
8.2108
1
Rocker shaft 1 31.964 to 31.980

F2C
Type
mm
Bushing housing in
rocker arms
32.025 to 32.041
32.025 to 32.041
Between bushings and

housings
0.045 to 0.077
0.045 to 0.077
TURBOCHARGER
Type HX55
End float -
Radial play -

ENGINE CONNECTION AND DISCONNECTION FROM THE RADIATOR

Figure 1
119971
Refitting
Removal
For the connection operation repeat the described
operations for the disconnection on the contrary
Prepare a suitable container near the pipe coupling (12) to and apply the following instructions:
recover the coolant. Detach and remove the pipe couplings - to control the engine elastic supports and to
(12) and (7) operating the clamps. replace them in case of deterioration ;
Detach and remove from the engine and from the radiator the
pipes (5) and (11) operating on their collars. - to control that the exhaust pipes are not
Remove the protection grilles (10) and the guard (8) of the deteriorated or are going to deteriorate; in this
fan operating on their fasteners. case you shall replace them;
Unscrew the engine side retaining nut of the fabric (6) so as - to clamp the screws and/or nuts to the
to release it. described couple;
Suitably lock the radiator group (9), the detach it from the
basement operating on the fasteners on both sides. - to fill the cooling system with cooling liquid;
Detach the air filter from the engine (1) operating from collar - to carry out bleeding operation from the fuel
(4) and the support (16) operating on the fasteners (15) after supply system as described in the suited
detaching the oil vapour hose (3) and the pipe coupling (4) paragraph.
from the turbocharger
Remove the screws which fasten the engine supports to the - to control engine oil level;
basement and detach the engine. - to carry out the tests and controls as described
To access the engine belt, it is necessary to remove the in the suited chapter.
protection guard (13), unscrewing the screws (14).




Recovery
To ensure optimised working conditions, in the following pages we are providing instructions for the overhaul control interventions,
checks and setting operations that must be performed on the engine at due planned dates.
The frequency of the maintenance operations is just an indication since the use of the engine is the main characteristic to determine
and evaluate replacements and checks.
It is not only allowed but recommended that the staff in charge of the maintenance should also carry out the necessary maintenance
and controlling operations even if not being included in the ones listed here below but that may be suggested by common sense
and by the specific conditions in which the engine is run.
Inspection and/or maintenance interventions
Intervention type Frequency (hours)

Engine
Engine visual inspection Daily
Check for water in the filter and prefilter Daily
Engine oil change Every 600 hours
Engine oil filter change Every 600 hours
Fuel prefilter change Every 300 hours
Fuel filter change Every 300 hours
Changing the Blow-by filter Every 600 hours
Check condition of water pump/alternator control belt Every 1200 hours
Check-up of EDC system by diagnostics tool -
Check valve lash and adjust, if required Every 1200 hours
Dry air filter change and container cleaning -
NOTE The maintenance operations are valid only if the setter fully complies with all the installation prescriptions provided by
FPT.
NOTE Low temperature diesel EN 590 specifications distinguish different classes of diesel fuel, identifying the characteristics
of those best suited to low temperatures. It is entirely up to the Oil companies to comply with these regulations, which
foresee that fuels suited to the climactic and geographic conditions of the various Countries be distributed.

OPERATIONS OUTSIDE THE PLAN

Daily checks
It is a good habit to execute, before engine start, a series of simple checks that might represent a valid warranty to avoid
inconveniences, even serious, during engine running. Such checks are usually up to the operators and to the vehicles drivers.
- Level controls and checks of any eventual leakage from the fuel, cooling and lubricating circuits.
- Notify the maintenance if any inconvenience is detected of if any filling is necessary.
After engine start and while engine is running, proceed with the following checks and controls:
- check presence of any eventual leakage from the fuel, cooling and lubricating circuits.
- Verify absence of noise or unusual rattle during engine working.
- Verify, using the vehicle devices, the prescribed pressure temperature and other parameters.
- Visual check of fumes (colour of exhaust emissions)
- Visual check of coolant in the expansion tank
NOTE Early air filter clogging is usually due to environmental conditions. For this reason, the filter should be changed if clogging
is signalled by the related sensor, regardless of the prescriptions that shall be observed if no specific indications have been
provided.
Every year Before winter

Check the antifreeze percentage in the engine cooling water
Every two year

Change engine coolant

MAINTENANCE PROCEDURES Top up via the tappet cover cap (2). When filling, remove the
Checks and controls dipstick (1) to facilitate the flow of oil.
Engine oil level check
The check must be executed when the engine is disconnected
and possibly cool.
The check can be made using the specially provided flexible
rod (1). In case of contact with the skin, rinse well with water
and detergent.
Adequately protect the skin and the eyes, operate in
full compliance with safety regulations.
Check of fuel system

The check operation consists in examining the fuel pipelines
running from the tank to the pre-filter (if provided in the
specific equipment), to the filter, to the injection pump and to
the injectors.
145841 Cooling system check

Draw off the rod from its slot and check that the level is within
the etched tags of minimum and maximum level. Check the pipes from the engine to radiator, and from the
Whether it should be difficult to make the evaluation, proceed expansion tank and vice versa; check for any leaks and inspect
cleaning the rod using a clean cloth with no rag grinding and the pipes, in particular near the connection clamps.
put it back in its slot. Draw it off again and check the level.
Verify that the radiator is clean, the correct working of the fan
In case the level results being close to the tag showing flywheels, the presence of any leakage from the connectors,
minimum level, provide filling lubrication of the engines from the manifold and from the radiating unit.
components.
Always be sure to add an oil with the same characteristics than
that contained in the cup. Are not allowed mixing which would
not provide proper lubrication of internal engine parts.
Due to the high temperatures achieved by the
system, do not operate immediately after the engines
disconnection, but wait for the time deemed
necessary for the cooling.
Protect the eyes and the skin from any eventual high
pressure jet of cooling liquid.
The density of the cooling liquid must be checked any how

every year before winter season and be replaced in any case
every two year.
In case of new filling, proceed bleeding system,

through the bleeds on the engine.
If bleeding of the system is not carried out, serious

inconvenience might be caused to the engine due
to the presence of air pockets in the engines head.
145842

Lubricating system check The drain screw (1) for draining off any water that may be
The check must be executed both when the engine contained in the fuel is located on the fuel filter support (2).
disconnected and when it is running. Place a container underneath the filter and slightly loosen the
screw. Drain the water eventually contained in the filters
Verify the presence of any oil leakage or blow-by from the bottom.
head, from the engine pan of from the heat exchanger.
Lock the screw (1) as soon as fuel starts bleeding.

In case of contact with the skin, rinse well with water Figure 5
and detergent.
Adequately protect the skin and the eyes, operate in
full compliance with safety regulations.
Check for water in the fuel filter and prefilter
The components of the system can be damaged

very quickly in presence of water or impurity within
the fuel.
Take prompt action on the filter to drain off the

145884
water in the fuel circuit.
Unhook the electrical connection (2) from the pre-filter (1)

and place a container under the pre-filter.
Drain off the water from the fuel pre-filter (1) using the drain
Figure 4
(3) located beneath it.
During this process take care the fuel does not damage the
sensor.
145883

Engine oil change - Check the level through the dipsick until when the filling
is next to the maximum level notch indicated on the dip-
Figure 6 sick.
Engine oil filter change

Figure 7
119975
We recommend to carry out the oil drainage when the motor

is hot.
Warning: We recommend to wear proper protec-
tions because of high motor service temperature. 119976
The motor oil reaches very high temperature: you

must always wear protection gloves. Drain the oil as described in the section Changing the engine
oil.
- Place a proper container for the oil collecting under the Remove the oil filter (1).
pan connected with the drain plug (3).
- Unscrew the plug (3) and then take out the control dip- NOTE Warning: the oil filter contains inside a quantity of
sick (1) and the inserting plug (2) to ease the downflow oil of about 1 kg.
of the lubrication oil.
Place properly a container for the liquid.
Warning: avoid the contact of skin with the motor
oil: in case of contact wash the skin with running
water.
The oil motor is very pollutant and harmful.
The motor oil is very pollutant: it must be disposed
In case of contact with the skin, wash with much water of according to the rules.
and detergent.
Protect properly skin and eyes: operate according to
safety rules.
Dispose of the residual properly following the rules.
NOTE Before refitting the new cartridge, wet seal using
engine oil.
Lock oil filter (1) by hand till contact to support and then lock
- After draining completely, screw on the plug (3) under
by of a rev. at prescribed tightening torque; pour oil in
the sump and tighten it to the prescribed torque.
engine ad described in Engine oil change chapter.
- Add the specified quantity of recommended engine oil
through the filler (2) of the tappets cover.
NOTE Use only the recommended oil or oil having the re-
quested features for the corrrect motor function-
ing.
In case of topping up, dont mix oils having different
features.
If you dont comply with theses rules, the service
warranty is no more valid.

Replace fuel tank prefilter Fuel filter change

Figure 8 Figure 9
1145886
145885
Disconnect electric connector (4). Unlock prefilter (1) and

change it. Before refitting a new cartridge, wet seal with fuel During this operation dont smoke and dont use free
oil or engine oil. Lock cartridge by hand till in contact with flames.
support, then lock it by of a rev. at predefined tightening
torque. Avoid to breathe the vapors coming from filter.
At change, filter cartridge must not be prefilled to After filters replacement the supply equipment
prevent circulating dirt that could damage ! deaeration must be carried out.
Unscrew the fuel filter cartridge (2).
Before fitting the new cartridge, wet seal with fuel or engine
oil.
Lock the new one by hand and carefully check that rubber seal
and contact surface are clean and in perfect conditions.
To bleed, pump with the hand pump (3) on the pre-filter (1) Lock cartridge by hand till contact with support and then lock
until fuel free of air flows from the loosened bleed screw (2). it for of a rev. at prescribed tightening torque.
Apply a transparent tube to the bleed screw (2) to facilitate
the operation and above all to avoid that the bled fuel
dangerously fouls the engine.
After operation, tighten the bleed screw (2).
When replacing the filter cartridge (2) do NOT fill it.
Start the engine and allow it to run for a few minutes to expel
any remaining air.
!
This operation is banned to avoid impurities entering
into the circuit, which would damage the
Fuel bleeding
Loosen the bleed screw (1) connecting the drainage by a
transparent flexible hose to a suitable container.

Figure 10 Figure 12
145887
With the hand pump (2) of the fuel pre-filter (1) pump until
fuel completely free of air bubbles flows from the bleed screw.
After the operation, tighten the bleed screw.
Start the engine and allow it to run at minimum for a few
minutes to expel any remaining air.
Changing the Blow-by filter
Figure 11 117692
at required torque.
Install cover (3) and lock screws (4) at required torque.
114018
Unlock screws (2) and remove cover (1). Remove the

centrifugal filter (3) underneath and replace it.

Check of water pump/alternator control belt condition Cleaning the air filter
Figure 14
Figure 13
130193
145888
Visually check that belt (4) is not worn out or broken; change Only proceed with the engine stopped.
it as described below, if required. - Remove the filter cover (3) after first unscrewing the
locking handle (2).
- Remove the external cartridge (1). During this operation,
take care to ensure that no dust get into the sleeve.
NOTE To be able to work on the engine belt you first need - Check that there is no dirt. If there is, clean the filter
to remove the protective casing (if applicable) by element as indicated below.
unscrewing the screws. - Blow dry compressed air through the filter element, from
the inside outward (maximum pressure 200 kPa). Do not
Use appropriate equipment (5) on the belt tensioner (6) in use detergents; do not use diesel.
the direction shown by the arrow and extract the belt (4) from - Never use tools to beat the filter element, and check its
the pulleys of the alternator (1), of the coolant pump (2) and condition before replacing it.
from the idler pulleys (3).
- Replace the filter if any breakages or tears are found.
Replace the worn belt with a new one.
- Check that the gasket at its base is in good condition.
Place the belt on the pulleys and the guide rollers.
- Reassemble by repeating the above operations in reverse
Place the automatic tightener in order to key the belt in the order.
functioning position.
Further adjustments are not required.
NOTE Take care to ensure that the parts are reassembled

Valve lash check a adjustment correctly. Imperfect assembly might result in
unfiltered air being sucked into the engine, causing
For correct operation, follow instructions contained in related serious damage.
chapter in section 3 Industrial Application.
Air filter replacement

Refer to the instructions provided for air filter cleaning.

Change coolant
Only proceed with the engine stopped and at a low

temperature, so as to avoid the risk of burning.
- Provide suitable containers to ensure that no coolant is
dispersed into the environment.
- Loosen the seal elements, remove the sleeves connecting
the engine circuit to the heat exchanger and wait until it
has emptied completely. When empty, repair the circuit
making sure that the sleeves are perfectly sealed.
- Fill up the circuit.
- Refill the engine and the heat exchanger until complete
top up.
- With the filler cap open, start the engine and keep it idling
for nearly one minute. This phase facilitates the cooling
liquid air bleed.
- Stop the engine and top up again.

PRINCIPLE ELECTRICAL DIAGRAM

Figure 15
119624

Key to components
BAT Starter battery 12V
M Starter motor
G Battery charger alternator
RFC Fuel filter heating resistor
TRFC Fuel filter heating thermostat
TPAC Water in the fuel filter transmitter
TBLA Low engine water level transmitter
TPO Engine oil pressure switch
TBPO Low engine oil level pressure switch
TTA Engine water temperature transmitter
TCE No fuel transmitter (option)
TBLC Float for fuel level
TS Engine water heater thermostat
EDC Engine electronic control unit
TATA High engine water temperature thermostat
SI Control panel - engine interface box
Function symbols for the control panel
ENGINE WATER TEMPERATURE THERMOMETER
LOW ENGINE OIL PRESSURE VISUAL WARNING
ENGINE OIL PRESSURE GAUGE
STARTING THE ENGINE (+50)
NO BATTERY CHARGING VISUAL WARNING
LOW ENGINE WATER LEVEL VISUAL WARNING
CAPTIVE KEY POSITIVE (+15)
WATER IN THE FUEL FILTER VISUAL WARNING
HIGH ENGINE WATER TEMPERATURE VISUAL WARNING
CAN LINE
CONTROL PANEL POWER SUPPLY
ENGINE PRE-HEATING
FUEL LEVEL VISUAL WARNING
NO FUEL VISUAL WARNING (OPTION)

ENGINE INTERFACE BOX

Description
Figure 16
107437
LIST OF COMPONENTS
K1. Power relay with key inserted (+15) - K2. Starting phase signal relay - K3. Starting relay - K4. Relay for pre-heating
resistance enabling - JP1. Jumper to select frequency (jumper on 1-2= 60Hz - jumper on 2-3= 50Hz) - JP2. Jumper for
operating mode selection (bond on 1-2= diagnosis - bond on 2-3= normal operation) - JP3. Jumper to select cold start signal
connection (1-2= connected - 2-3= disconnected) - JP4. Jumper to select heat. function for cold starting (1-2= connected -
2-3= disconnected) - JP5. Jumper for Can Line selection (1-2= Can Line connected - 2-3= Can Line not connected) -
JP6. Not used - JP8. Not used - BP1. Switch for blink-code signal request - LD1. LED signalling blink/code -
F1. 10A fuse for starting engine - F2. 3A fuse for diagnostics - F3. 20A protection fuse for pre-heating resistance -
F4. 30A fuse for electronic control unit - F5. 10A fuse for control panel - F6. 5A fuse for cut-in +15 ON ECU - F7. 20A
protection fuse for fuel filter heater - F8. Not used - F9. Not used - J1. Connector for power connections - J2. Connector
for interface with engine control unit - J3. Connector for interface with control panel - J7. Connector for interface with
control panel - J9. Connector for interface with control panel.

Connectors
Figure 17
107439
107438
107437
CONNECTOR J1 on engine control panel interface box for power supply (GECURSOR300E/350E/400E)
1 To terminal 50 of starter motor
2 Supply from F3 for fuel filter heating resistance
3 Battery negative
4 Direct positive to battery
5 Spare
6 Spare

CONNECTOR J2 on engine control panel interface box for EDC ECU connections
1 +15 from ignition key
2 12 jumper
3 Negative signal from oil low pressure pressure switch
4 Signal from water temperature sensor
5 Negative signal from water high temperature pressure switch
6 Signal from fuel zero level transmitter
7 Fuel low level signal
8 Supply of water presence in fuel sensor
9 Signal from water presence in fuel sensor
10 Ground of water presence in fuel sensor
11 Jumper with 37
12 Jumper with 2
13 Positive +30
14 Positive +30
17 Supply of water low level sensor
18 Signal from water low level sensor
19 Ground of water low level sensor
20 No recharge from alternator signal
22 Ground for diagnosis lamp
23 Positive signal for diagnosis lamp
25 Torque limiting resistance
27 Line K - diagnosis EDC
29 Negative signal from EDC system diagnostic switch
31 Signal from oil pressure sensor
32 Negative signal from water heater thermostat
33 Ground
37 Jumper with 11
40 Positive signal for excitation of contactor of fuel filter heater
41 Positive +30
42 Positive +30
46 Ground
47 Ground
48 Positive for cold start lamp
49 Positive for excitation of pre-heating contactor
50 Pre-heating contactor ground
53 Negative signal from EDC system diagnostic switch
54 Engine revs signal from EDC control unit
55 Line CAN L
56 Line CAN H
NOTA Pins 1 and 2 of EDC ECU are connected to battery negative

CONNECTOR J3 inside the engine interface box for signals to control panel
1 Free
2 From the engine water temperature transmitter for signal to thermometer on control panel
3 From the low engine oil pressure switch for visual warning on control panel
4 From engine oil pressure switch for signal to pressure gauge on control panel
5 Free
6 To the key switch (+50) on control panel
7 From the alternator for battery charging visual indicator on control panel
8 From the low engine water level transmitter for visual warning on control panel
9 +15
10 From the water in fuel filter transmitter for visual warning on control panel
11 Free
12 Free
CONNECTOR J7 inside the engine interface box for signals to control panel
1 From the engine coolant high temp. thermostat for visual signal on control panel
2 CAN line L to the control panel
3 Positive to power control panel
4 Negative to power control panel
5 CAN line H to the control panel
6 From the engine water heater thermostat to the control panel
7 From the fuel level transmitter for visual warning on control panel
8 From the no fuel transmitter (opt)
CONNECTOR J9 inside the engine interface box

1 Cold start signal (option) if jumper JP3 set on 1-2
2 Cold start signal (option) if jumper JP3 set on 1-2
3 Cold start heater relay (option) if jumper JP4 set on 1-2
4 Cold start heater relay (option) if jumper JP4 set on 1-2
5 Free
6 Free
7 Free
8 Free
9 Free
10 Free

EDC 7 UC31 ELECTRONIC CONTROL UNIT
Figure 18
C A
102373
A. Electro-injector connector - B. Chassis connector - C. Sensor connector

EDC control unit PIN-OUT

Chassis connector B
Figure 19
71 89 72 54 6 11
1
7
12
102376
53 35 18 36 17
ECU
Cable Function
Pin
2 7151 Positive +30
3 7151 Positive +30
5 0150 Ground
6 0150 Ground
8 7151 Positive +30
9 7151 Positive +30
10 0150 Ground
11 0150 Ground
12 8885 Positive for excitation of pre-heating contactor
13 0000 Ground
21 - Jumper with 74
22 5535 Positive signal for diagnosis lamp
29 0000 Ground
30 0535 Ground for diagnosis lamp
33 5584 Engine revs signal from EDC control unit
34 6109 Line CAN L
35 6108 Line CAN H
36 Positive signal for excitation of contactor of fuel filter heater
40 7731 +15 from ignition key
56 5553 Positive for cold start lamp
62 0021 Torque limiting resistance
66 5120 Torque limiting resistance
74 - Jumper with 21
75 0094 Pre-heating contactor ground
85 0156 Negative signal from EDC system diagnostic switch
89 2298 Line K - diagnosis EDC


F2ce9687a B C

Uploaded by

Document Informationclick to expand document informationDATOS TÉCNICOS Y REPARACIÓN DE IVECO

Document Informationclick to expand document information

Copyright:

Available Formats

F2ce9687a B C

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

F2ce9687a B C

Uploaded by

Copyright:

Available Formats

CURSOR TIER 3

Technical and Repair manual

This publication has been drawn up for qualified and

Before performing any operation check that the part relevant

Operations are to be performed by following the indications

Each repair must aim to restore operating efficiency and safety

FPT cannot be held liable for modifications, alterations or other

FPT is not liable for repairing interventions.

FPT will provide further details required to carry out the

Data included in this publication may not be up-to-date

If issues on this publication differ from what is actually noticed

It is forbidden to copy this text or any of its parts and all

F2C CURSOR ENGINES

Cursor F2C Part 1

Cursor engines application G-Drive Part 2

Print P2D32C006E Base - May 2010

Base - May 2010 Print P2D32C006E

PREFACE TO USERS GUIDELINE MANUAL . . 3

- Bonding and screening . . . . . . . . . . . . . . . . . . . 8

CONVERSIONS BETWEEN THE MAIN UNITS

KEY OF LECTURE OF THE HEADINGS

Print P2D32C006E Base - May 2010

Base - May 2010 Print P2D32C006E

PREFACE TO USERS GUIDELINE MANUAL

Danger for persons

Danger of serious damage for the assembly

NOTE It indicates an additional explanation for a piece of information.

1 1 = housing for connecting rod small end bush

Print P2D32C006E Base - May 2010

Tighten to torque + angle value Rolling torque

Press or caulk Rotation

Base - May 2010 Print P2D32C006E

Print P2D32C006E Base - May 2010

Base - May 2010 Print P2D32C006E

GENERAL WARNINGS ON THE ELECTRIC SYSTEM

Print P2D32C006E Base - May 2010

Bonding and screening

Further, following warnings are to be compulsorily observed for electronic components:

1. NEGATIVE CABLES STAR CONNECTION TO SYSTEM BONDING M

2. SCREENING THROUGH METALLIC BRAIDING OF A CABLE TO AN ELECTRONIC COMPONENT C. CONNECTOR

Base - May 2010 Print P2D32C006E

CONVERSIONS BETWEEN THE MAIN UNITS OF MEASUREMENT OF THE

Print P2D32C006E Base - May 2010

KEY OF LECTURE OF THE HEADINGS AND FOOTNOTES

Type of Section Page

Language Basic edition referred to When month - year

Base - May 2010 Print P2D32C006E

Overhaul and technical specifications 4

Safety prescriptions Appendix

Print P2D32C006E Base - May 2010

Base - May 2010 Print P2D32C006E

Section Description Page Date of revision

Print P2D32C006E Base - May 2010

Base - May 2010 Print P2D32C006E

MAPPING BETWEEN TECHNICAL

Print P2D32C006 E Base - May 2010

Base - May 2010 Print P2D32C006 E