TA-202:MANUFACTURING PROCESSES

1
* BE KEEN OBSERVER

EXAMPLES OF SOME SCIENTISTS

2
 SIR ISSAC NEWTON

KEEN OBSERVATIONS HAD LED TO BIG INVENTIONS

WHY IT FELL DOWNWARD?

WHY DID IT NOT GO UP?

THEORY OF GRAVITATION

3
DR. C. V. RAMAN

OBSERVING THE WAVES IN SEA

WHILE GOING ABROAD

WHY THE WATER OF

SEA LOOKS BLUE IN
COLOUR?

LED TO THE INVENTION OF

RAMAN EFFECTS

NOBLE PRI ZE
WINNER
4
IS IT NECESSARY FOR THE TOOL TO BE
HARDER THAN WORKPIECE
?

HOW A ROPE CAN

WEAR THE PULLEY ?

WORN OUT PULLEY

BY A ROPE

5
INTRODUCTION

6
 ENGINEERING MATERIALS

METALS AND ALLOYS PLASTICS AND COMPOSITES CERAMICS

GETTING MORE POPULARITY

DEFINITE ADVANTAGES OVER
OTHERS

HOW TO
MACHINE
THEM

?
SOLUTION

ADVANCED MACHINING PROCESSES

Prof. V.K.Jain, Mechanical Engineering

7
Department, I.I.T. Kanpur
 PRESENT DAY DEMAND TRENDS IN INDUSTRIES
(AEROSPACE , MISSILES , AUTOMOBILES, NUCLEAR REACTORS, ETC.)

ENGG. MATERIALS HAVING MUCH ULTRA HIGH STRENGTH , HARDNESS

SUPERIOR VERY HIGH TEMPTURE RESISTANCE
PROPERTIES DIFFICULT TO MACHINE BY
CONVENVENTIONAL MACHINING
METHODS

WORK PIECE MATERIAL HARDNESS >> TOOL MATERIAL HARDNESS

HOW TO SOLVE THE PROBLEM

?
ADVANCED MACHINING PROCESSES
WORKPIECE HARDNESS DOES NOT MATTER IN AMPs

Prof. V.K.Jain, Mechanical Engineering

8
Department, I.I.T. Kanpur
 LIMITATIONS OF CONVENTIONAL MACHINING METHODS
(WORKPIECE HARDNESS, SURFACE ROUGHNESS, 3-D PARTS,
COMPLEX GEOMETRIES)
INCREASED WORKPIECE HARDNESS DECREASED ECONOMIC
WHY DO YOU CUTTING SPEED LOWER PRODUCTIVITY
NEED ADVANCED
MACHINING
PROCESSES RAPID IMPROVEMENTS IN THE PROPERTIES OF MATERIALS
(WORKPIECEHARDNESS, STRENGTH, ETC.)
(AMPs)

METALS & NON METALS : STAINLESS STEEL , HIGH STRENGTH

? TEMPERATURE RESISTANT (HSRT) SUPER ALLOYS: STELLITE, ETC.

TOOL MATERIAL HARDNESS >> WORKPIECE HARDNESS

REQUIRES MUCH SUPERIOR QUALITY OF TOOL

MATERIALS

Prof. V.K.Jain, Mechanical Engineering

9
Department, I.I.T. Kanpur
 WHY DO YOU
NEED ADVANCED
MACHINING
PROCESSES
(AMPs) PRODUCT REQUIREMENTS

COMPLEX SHAPES
? MACHINING IN INACCESSIBLE AREAS

LOW TOLERANCES (SAY, 10 m)

BETTER SURFACE INTEGRITY (NO SURFACE DEFECTS,

ETC.)

HIGH SURFACE FINISH (NANO LEVEL Ra VALUE =>nm)

MINIATURIZATION OF PRODUCTS (EXAMPLES: LANDLINE

PHONE & MOBILE, OLD COMPUTERS & LAP TOP, ETC.)

HIGH MRR

10
Prof. V.K.Jain, Mechanical Engineering Department, I.I.T. Kanpur
 HIGH PRODUCTION RATE WHILE PROCESSING DIFFICULT TO-
MACHINE MATERIALS
LOW COST OF PRODUCTION
PRECISION AND ULTRAPRECISION MACHINING
(NANO-METER MACHINING)

WHY DO YOU
NEED ADVANCED
MACHINING
PROCESSES
REQUIRES MATERIAL REMOVAL IN THE FORM OF ATOMS AND / OR
MOLECULES
?

ADVANCED MACHINING PROCESSES

(AMPs)
Prof. V.K.Jain, Mechanical Engineering Department, I.I.T. Kanpur 11
 WHY DO YOU
NEED ADVANCED
MACHINING
PROCESSES ?

some examples

Prof. V.K.Jain, Mechanical Engineering

12
Department, I.I.T. Kanpur
 Fabrication

Building of machines, structures, or process equipment by cutting,

shaping and assembling components made from raw materials.

Fabrication
IGNORING MESO AND NANO FABRICATION
Meso / Macro
fabrication Micro fabrication
Process of fabrication of
Process of fabrication of
miniature structures / features
structures that are measurable
of
and observable.
m sizes

Visible by naked eye Need microscopic equipments

Dimensions >= 1mm 999 nm <=Dimensions <= 999 m

13
 CLASSIFICATION BASED ON THE KIND OF ENERGY USED : MACHANICAL,
THERMOELECTRIC, ELECTROCHEMICAL & CHEMICAL, BIOCHEMICAL

ELECTROCHEMICAL &
MECHANICAL THERMOELECTRIC
CHEMICAL

MACHINING
PLASMA ARC MACHINING (PAM) ELECTROCHEMICAL MACHINING
ABRASIVE JET MACHINING (AJM)
(ECM)

ULTRASONIC MACHINING (USM) LASER BEAM MACHINING (LBM) CHEMICAL MACHINING (CHM)

WATER JET MACHINING ELECTRON BEAM

BIOCHEMICAL MACHINING (BM)
(WJM) MACHINING (EBM )

ABRASIVE WATER JET MACHINING ELECTRIC DISCHARRGE MACHINING (

(A WJM) EDM)

FINISHING
ABRASIVE FLOW FINISHING (AFM) ION BEAM MACHINING(IBM)

MAGNETIC ABRASIVE FINISHING

(MAF)

MAGNETORHEOLOGICAL
FINISHING (MRF) Prof. V.K.Jain, Mechanical Engineering
14
Department, I.I.T. Kanpur
MACHINING OF COMPLEX SHAPED WORKPIECES?
ELECTROCHEMICAL MACHINING

HOLE NORMAL TO THE WALL Contoured Hole Drilled In Inconel Using ECM
Turbine Blade with cooling Holes

MALE

FEMALE

PRECISION WIRE EDM 15 EDM

Prof. V.K.Jain, Mechanical Engineering Department, I.I.T. TAPER 3-D CUTTING USING TRAVELING WIRE-
Kanpur
 PATTERN OF HOLES DRILLED BY EBM
HOLE =0.006 mm (6 m);
PART OF A HELICOPTER HOLE=0.09 mm HOLES DENSITY = 4000/cm2 HOLES DENSITY = 200,000 / cm2 ;
TURBINE HOLES DRILLED WORKPIECE- S.S.;
BY EBM THICKNESS = 0.12 mm; TIME= 2s / HOLE
THICK = 0.2 MM; TIME = 10 S/HOLE

AFF MEDIA ACTS AS A SELF-DEFORMABLE STONE

Prof. V.K.Jain, Mechanical Engineering

16
Department, I.I.T. Kanpur
 PERFORMANCE IS INDEPENDENT OF STRENGTH

BARRIER.

SOME
PERFORMANCE DEPENDS ON THERMAL, ELECTRICAL,
IMPORTANT
MAGNETIC OR / AND CHEMICAL PROPERTIES OF
CHARACTERISTICS
OF AMPs WORKPIECE MATERIALS.

&
USE DIFFERENT KINDS OF ENERGY IN DIRECT FORM.
MACHINE
TOOLS IN GENERAL, LOW MRR BUT BETTER QUALITY

PRODUCTS.

COMPARATIVELY HIGH INITIAL INVESTEMENT COST

OF MACHINE TOOLS AND HIGH OPERATING COST .

Prof. V.K.Jain, Mechanical Engineering

17
Department, I.I.T. Kanpur
ADVANCED MACHINING PROCESSES

CAN WATER CUT THE METALS ?

YES. BUT HOW?

Prof. V.K.Jain, Mechanical Engineering

18
Department, I.I.T. Kanpur
 WATER JET MACHINING (WJM), ABRASIVE WATER JET
MACHINING (AWJM) , ABRASIVE JET MACHINING (AJM)

HOW DOES IT WORK? K.E. of WATER AND / OR ABRASIVE PARTICLES MAKES IT TO HAPPEN.

VELOCITY OF THE ABRASIVE WATER JET AS HIGH AS 900 m/s.

Prof. V.K.Jain, Mechanical Engineering

19
Department, I.I.T. Kanpur
ELETRIC DISCHARGE MACHINING

LAZERANKO

WORN OUT MARKS

Prof. V.K.Jain, Mechanical Engineering

20
Department, I.I.T. Kanpur
LASER BEAM MACHINING (LBM)

Prof. V.K.Jain, Mechanical Engineering

21
Department, I.I.T. Kanpur
LASER BEAM MACHINING (LBM)

Prof. V.K.Jain, Mechanical Engineering

22
Department, I.I.T. Kanpur
ULTRASONIC MACHINING

Prof. V.K.Jain, Mechanical Engineering

23
Department, I.I.T. Kanpur
PLASMA ARC MACHINING (PAM)

Prof. V.K.Jain, Mechanical Engineering

24
Department, I.I.T. Kanpur
 OVERVIEW OF
ADVANCED MACHINING
PROCESSES

25
ELECTROCHEMICAL
MACHINING (ECM)

26
 ELECTRICHEMICAL MACHINING (ECM)

ECM PROCESS IS ALSO KNOWN AS A

CONTACTLESS ELECTROCHEMICAL FORMING PROCESS
ELECTROCHEMICAL ENERGY DETACHES METAL FROM ANODE ATOM BY ATOM

27
 ELECTROCHEMICAL REACTIONS
TYPES OF ELECTROLYTES USED IN ECM

ACIDIC ALKALINE NEUTRAL

2 H2 O + 2e H2 + 2OH
2Fe 2e 2Fe++
Fe++ + 2OH Fe(OH)2
2Fe + 4 H2 O Fe(OH)3 + H2 + O2

Fe(OH)2 , Fe(OH)3 INSOLUBLE IN WATER

POSITIVE IONS CONVERT AS HYDROXIDES (FERROUS OR

FERRIC HYDROXIDE IN CASE OF IRON AS ANODE/ WORK
MATERIAL)
IEG < 1 mm, VOLTAGE 8-20
28
NO ELECTROLYTE IS BEING CONSUMED IN THE PROCESS
 WORKING PRINCIPLE OF ECM

FARADAY S LAWS OF ELECTROLYSIS

m itE

MASS OF DISSOLVED METAL GRAM CHEMICAL EQUIVALENT = A / Z

CURENT TIME
AATOMIC MASS OF ANODE, Z VALENCY OF DISSOLUTION OF ANODE

29
 MATERIAL REMOVAL IN ECM

MATERIAL REMOVAL (m) IN ECM FOLLOWS FARADAYS LAWS

OF ELECTROLYSIS:
ItE .(1)
m=
F
MATERIAL RAMOVAL RATE (MRR) CAN BE OBTAINED AS
.
m IE .(1a)
= m=
t F
Where, m is amount of material removed in grams, I is current flowing
through the IEG in Amperes, t Is time of current flow (or ECM), E
Is gram chemical equivalent of anode material, F is Faradays
.

constant (Coulombs or A.s) or constant of proportionality . and m is material removal
rate in g/s. 30
 MATERIAL REMOVAL IN ECM
MRR CAN BE OBTAINED AS

a va a Aa ( ya ) IE
= =
t (t ) F

WHERE, a = DENSITY OF ANODE, Va = VOLUME OF MATERIAL

REMOVED FROM THE ANODE IN TIME t, Aa = X- SECTIONAL AREA ON THE
ANODE FROM WHICH MATERIAL IS BEING REMOVED IN TIME t, ya IS THE
THICKNNESS OF MATERIAL REMOVED IN TIME t. V IS OVER POTENTIAL, k=
ELECTROLYTES ELECTRICAL CONDUCTIVITY

Prof. V.K.Jain, Mech. Engg. Deptt., I.I.T.

31
Kanpur
 MATERIAL REMOVAL IN ECM

FROM ABOVE EQUATION, WE CAN WRITE

( ya ) IE
MRRl = =
(t ) F a Aa

JE
MRRl = .(2)
F a
J=I/Aa=V/R=V/(l/A)
(J = CURRENT DENSITY = I/Aa)
=(1/k)

ABOVE EQUATION CAN BE WRITTEN AS J=((V- V)/A) (kA/y)

=Resistance

V V kAa E
MRRl =
Anode density

Aa y F a
32
Prof. V.K.Jain, Mech. Engg. Deptt., I.I.T.
Kanpur
THERMAL MICROMACHINING PROCESSES

ELECTRIC DISCHARGE MICROMACHINIG

BEAM MICROMACHINING

1. LASER BEAM MICROMACHINING

2. ELECTRON BEAM MICROMACHINING
3.ION BEAM MICROMACHINING
(NOT A THERMAL PROCESS)

33
 BEAM TECHNOLOGY
IBM LBM
EBM

IEG = A FEW HUNDRED m

CRATER

100 M ICRONS

CRATER

Dr. V.K.Jain, I.I.T. Kanpur;[email protected] 34

SHORT PULSE LASER MACHINING
ELECTRIC DISCHARGE
MACHINING (EDM)

35
 ELECTRIC DISCHARGE MACHINING
(EDM)

SPARKS CREATED DELIBERATELY

HEAT IN A LOCALIZED AREA
IEG = A FEW HUNDRED m

CRATER
MELTING AND /
OR VAPORIZATION
100 M ICRONS

CRATER

36
ELECTRIC DISCHARGE MACHINING : HOW SPARKING TAKES PLACE?

Asperity

PULSED D.C.
SOURCE

Ion

PULSED
D.C.
SOURCE

Prof. V.K.Jain, Mechanical Engineering 37

Department, I.I.T. Kanpur
 EDM: WORKING PRINCIPLE

BREAK DOWN OF DIELECTRIC (AT PRE DETERMINED ELECTRIC FIELD)

OF DIELECTRIC (USUALLY KEROSENE OR WATER) TAKES PLACE
BETWEEN TWO ELECTRODES (TOOL & WORKPIECE).

DIELECTRIC IONIZATION MOLECULES (ELECTRONS FROM CATHODE

COLLIDE THE MOLECULES ) SPLIT INTO IONS, AND ELECTRONS.

IONS MOVE TOWARDS CATHODE AND ELECTRONS MOVE TOWARDS

ANODE

ELECTRONS HIT THE CATHODE AND IONS HIT ANODE

DUE TO THEIR K.E., THEY PRODUCE HEAT ON CATHODE (LESS) AND

ANODE (MORE)

THIS HEAT MELTS AND EVEN VAPORIZES A SMALL PART OF CATHODE

AND ANODE.

Prof. V.K.Jain, Mechanical Engineering

38
Department, I.I.T. Kanpur
ELECTRIC DISCHARGE MACHINING (EDM) : MACHINE ELEMENTS

Servo system
Control gap

IEG

Ionized
fluid

DC
Pulse
Generator

REPLICA OF THE TOOL WORKPIECE

Prof. V.K.Jain, Mechanical Engineering
39
Department, I.I.T. Kanpur
 ELECTRIC DISCHARGE MACHINING (EDM)
POLARITY IN EDM

VOLTAGE / CURRENT
PULSES IN EDM
1 s

Ignition
delay

40
(SOURCE: Advanced Machining Processes by V.K.Jain, Allied Publishers, New Delhi)
ELECTRON BEAM MACHINING (EBM)

Prof. V.K.Jain, Mechanical Engineering

41
Department, I.I.T. Kanpur
 FOCUSSED ION BEAM MACHNING (IBM)

SPUTTERING OFF: KNOCKING OUT ATOMS FROM THE WORK-PIECE SURFACE BY THE KINETIC
MOMENTUM TRANSFER FROM INCIDENT ION TO THE TARGET ATOMS

REMOVAL OF ATOMS WILL OCCUR WHEN THE ACTUAL ENERGY TRANSFERRED EXCEEDS THE
USUAL BINDING ENERGY.

FIG. SCHEMATIC ILLUSTRATION

AT SUFFICIENTLY HIGH ENERGY, THE CASCADING EVENTS WILL PENETRATE MORE DEEPLY INTO THE
SOLID, SEVERAL ATOMS OR MOLECULES WILL BE EJECTED OUT AND THE BOMBARDING ION WILL
BECOME IMPLANTED DEEP WITHIN THE MATERIAL.

Prof. V.K.Jain, Mechanical Engineering

42
Department, I.I.T. Kanpur
MECHANICAL MICROMACHINING PROCESSES

ULTRASONIC MICROMACHINIG

ABRASIVE JET MICROMACHINING

1. WATERJET MICROMACHINING
2. ABRASIVE WATER JET MICROMACHINING

43
 PRINCIPLE OF MECHANICAL MICROMACHINING MECHANISM
ABRASIVE WATR JET MACHINING
ULTRASONIC MACHINING

ABRASIVE JET
MACHINING

AWJM, AJM, USM

Mechanism of material Mechanism of material
removal in ductile material removal in brittle
material

FORCES ACTING ON EACH PARTICLE AND

PARTICLE SIZE
WILL DEC IDE THE SCALE OF MATERIAL
REMOVED : MACRO, MICRO, NANO

Dr. V.K.Jain, I.I.T. Kanpur;[email protected] 44

ABRASIVE WATER JET MICRO-MACHINING (AWJM)

1. Low feed rate

2. Medium feed rate

3. High feed rate 45

APPLICATIONS OF ABRASIVE WATER JET CUTTING
(AWJC)

Granite cutting

(COURTESY : IITM CHENNAI)

46
 Material Removal Processes

Micro/nano machining Micro/nano finishing

Traditional machining processes Traditional finishing processes

Advanced machining processes Advanced finishing processes

47
 Micro-manufacturing
A set of processes used to fabricate features,
components, or systems with dimensions most
conveniently described in micrometers

48
MICROMACHINING : AN OVERVIEW

49
 Why miniaturization?

Minimizing energy and materials use in manufacturing

Reduction of power budget

Faster devices
Increased selectivity and sensitivity

Improved accuracy and reliability

Cost / performance advantages

Integration with electronics, simplifying systems

50
51
 Methods of Micro-manufacturing

Material Material Forming /

Joining Casting
deposition Removal shaping

Traditional
Electro chemical Rolling Welding
material
spark deposition
removal
processes
Forging Brazing
Electro discharge
deposition Advanced
material Extrusion &
Soldering
removal drawing
Chemical vapor processes
deposition Sheet metal
Physical vapor
deposition

Rapid prototype /
rapid tooling

LIGA

MICROFABRICATION IS GOING TO WITNESS AN

EXCELLENCE IN R & D AT A REMARKABLE RATE
 -MACHINING METHODS

Traditional Advanced

-turning Mechanical Thermal Chemical

-milling -AJM -EDM ECMM

-drilling -USM -EBM PCMM

-grinding -AWJM -LBM

AFM, MAF, M-
RAFF, MPF
-PAM

HYBRID

-ECSM -ECG -EDG ELID, etc

 MICRO MACHINING
Micro Machining

Removal of material at micro level

1.Macro components but material removal is at micro/nano level
2.Micro/nano components and material removal is at micro/nano level (Ex.
MEMS, NEMS)

Unfortunately , the present

day notion is

LEG OF A HOUSE FLY

Machining of highly miniature

components with miniature features.
Literally it should NOT be so
MORE CORRECT DEFINITION IS material removal is at micro/nano level
54
SIZE : 2mm x 2mm WITH NO CONSTRAINT ON THE SIZE OF THE COMPONENT
SOME MICROMACHINED PARTS

LASER-CUT STENTLIKE PATTERN IN MINIATURE

STAINLESS- STEEL TUBE WITH 1.25-mm OD.

LASER-DRILLED HOLE (DIA. 15 m)

PATTERN IN POLYURETHANE TUBE

55
ELECTRO DISCHARGE
MICROMACHINING
(EDMM)

56
 EXAMPLES OF EDMM

30-micron shafts and 50-micron Holes as small as 6.5 microns in diameter

57
holes produced by micro-EDM. and an aspect ratio of 7.5
 EXAMPLES OF EDMM

MICROFLUIDICS MIXER
PIN OVER
MOULDING
JIG (655
HOLES)

0.52 mm DIA
EXTRUSION DIE

MICRO
GEARS(DIA 0.52
LADDER WITH 100 m mm)
GAP BETWEEN TEETH

58
LASER BEAM MICROMACHINING
(LBMM)

59
 BASIC PRINCIPLES OF LASER

LIGHT AMPLIFICATION BY STIMULATED EMISSION OF RADIATION.

LIGHT ENERGY OF A PARTICULAR FREQUENCY CAN BE USED TO

STIMULATE THE ELECTRONS IN AN ATOM TO EMIT ADDITIONAL LIGHT
WITH EXACTLY THE SAME CHARACTERISTICS AS THE ORIGINAL
STIMULATING LIGHT SOURCE.

PHOTON ENERGY IS PROPORTIONAL TO FREQUENCY BUT INVERSELY

PROPORTIONAL TO WAVELENGTH.

THE PHOTON STIMULATES THE ATOM, CAUSING IT TO EMIT AN

ADDITIONAL PHOTON WITH IDENTICAL CHARACTERISTICS TO THE
STIMULATING PHOTON.

60
 PROPERTIES OF LASER BEAM

MONOCHROMATIC SINGLE WAVELENGTH.

COHERENT SAME PHASE RELATIONSHIP.

DIRECTIONAL LOW DIVERGENCE, BEAM SPREADS VERY LITTLE.

INTENSE HIGH DENSITY OF USABLE PHOTONS.

TWO TYPES OF LASERS: CONTINUOUS WAVE AND PULSED LASERS

LONG PULSED LASES AND SHORT PULSED LASERS

61
 TYPES OF LASERS

TIME SCALES:

Millisecond 1*10-3 second

Micro second 1*10-6 second
Nano second 1*10-9 second
Pico second 1*10-12 second
Femto second 1*10-15 second

62
 LONG PULSE LASER MACHINING

ANIMATION

DEMERITS OF LONG
PULSE LASER

63
 SHORT PULSE LASER MACHINING

MERITS OF SHORT
PULSE LASER

64
APPLICATIONS OF LBM

MICRO CUTTING IN A TUNGSTEN PIN USING

511nm ND LASER

MICRO FLUIDIC DEVICE IN SILICON SHOWING

LASER DRILLED VIA HOLE AND CONNECTING
CHANNEL

65
LASERS AND THEIR CONFIGURATION

MICRO MACHINED LETTERS ON A SINGLE HUMAN HAIR

NOTE THE CLARITY OF THE LETTERS IN THE CLOSE-UP VIEW

66
ELECTRON BEAM MICROMACHINING
(EBMM)

67
 BASICS OF EBM

IT WORKS IN MUCH THE SAME WAY AS A CATHODE RAY TUBE IN A

TELEVISION.

CATHODE SECTION(GENERATES BEAM)

ANODE SECTION(ACCELERATES THE BEAM)

LENS SYSTEM CONVERGES AND DEFLECTS THE BEAM TO

THE DESIRED POSITION

ELECTRON-BEAM
MACHINING PROCESS

68
WHY VACCUM IS REQUIRED?

ELECTRON-BEAM IN A
VACUUM

ELECTRON BEAM IN
AMBIENT AIR

69
PATTERN OF HOLES DRILLED BY EBM

HOLE=0.09 mm
HOLES DENSITY = 4000/cm2
WORKPIECE- S.S.
THICK = 0.2 mm
TIME = 10 S/HOLE

HOLE =0.006 mm (6 m)
HOLES DENSITY = 200,000 / cm2
THICKNESS = 0.12 mm
TIME= 2s / HOLE

70
ELECTRO CHEMICAL
MICROMACHINING
(ECMM)

71
 ELECTRO CHEMICAL MACHINING (ECM)

Fe + 2H2O Fe(OH)2 + H2

4Fe(OH)2 + 2H2O + O2 4Fe(OH)3

72
 APPLICATIONS OF ECMM

MICRO-HOLES PRODUCED ON A
Ti6Al4V CYLINDER USING JET-EMM

PRODUCTION OF HIGH ACCURACY HOLES

CU STRUCTURE (SMALL PRISM, 5 m BY

10 m BY 12 m) MACHINED INTO THE
CU SHEET OF AN ELECTRONIC CIRCUIT
BOARD

3D MICRO-MACHINING
73
 APPLICATIONS OF ECMM

Titanium surface microstructure

by through-mask EMM

LONG-RANGE ACCURACY AND

REPRODUCIBILITY OF 30 m CAVITIES

SMOOTH SURFACE AND SHARP BORDERS THAT

ARE ACHIEVED UNDER OPTIMIZED DISSOLUTION
CONDITIONS

74
 ELECTRO CHEMICAL DEBURRING (ECD)
Adaptation of ECM to remove burrs or round sharp corners on holes in metal
parts produced by conventional through-hole drilling.

75
ION BEAM MICROMACHINING
(IBMM)

76
 MECHANISM OF ION BEAM MACHINING
SPUTTERING OFF: KNOCKING OUT ATOMS FROM THE WORK-PIECE
SURFACE BY THE KINETIC MOMENTUM TRANSFER FROM INCIDENT
ION TO THE TARGET ATOMS
REMOVAL OF ATOMS WILL OCCUR WHEN THE ACTUAL ENERGY
TRANSFERRED EXCEEDS THE USUAL BINDING ENERGY.

FIG.SCHEMATIC ILLUSTRATION OF THE MECHANISM OF MATERIAL REMOVAL IN IBM

AT SUFFICIENTLY HIGH ENERGY, THE CASCADING EVENTS WILL

PENETRATE MORE DEEPLY INTO THE SOLID, SEVERAL ATOMS OR
MOLECULES WILL BE EJECTED OUT AND THE BOMBARDING ION
WILL BECOME IMPLANTED DEEP WITHIN THE MATERIAL.
77
Coil 700 nm pitch, 80 nm line width,
diamond like amorphous carbon,
Fabricated by FIB induced deposition

(a) Radial DLC free-space-wiring grown into eight

directions from the center. (b) Radial DLC free-
space-wiring grown into 16 directions from the
center.

T. Morita et al, J. Vac. Sci. Technol. B 21 (2003)

Micro wine glass with 2.75 m external

diameter and 12 m height.

Shinji Matsui et al, J. Vac. Sci. Technol. B 18(2000) 3181 78

 TYPICAL MATERIAL REMOVAL RATE IN ION
BEAM MACHINING
TABLE1: REMOVAL RATES BY IBM (SPENCER AND SCHMIDIT,1972 [1])
DATA : ARGON ION BEAM 60 TO 700 FROM NORMAL
PRESSURE = 3X10-4 TORR
VOLTAGE = 6 KV
CURRENT = 100 A
CURRENT DENSITY = 1 MACM-2 OVER 1 CM DIAMETER AREA
MATERIAL REMOVAL (MILLING) RATE, (M HR-1)
QUARTZ 2
GARNET 1
CERAMIC 1
GLASS 1
GOLD 2
SILVER 3
PHOTO RESIST MATERIAL (KTFR) 1
PERMALLOY 1
DIAMOND 1

79
NANOFINISHING PROCESSES: AN OVERVIEW

80
 Micro / nano finishing

Traditional Advanced
Grinding AFM

MAF
Lapping
MRF
Honing CMP

MRAFF

ELID
SHAPE AND SIZE CONSTRAINTS MFP
WITH EACH OF THESE
TRADITIONAL FINISHING PROCESSES
CMMRF

81
 MAF AFM MRAFF
FLEXIBLE MAGNETIC Ft
Magnetic Electromagnet pole
ABRASIVE BRUSH
lines of Fn
force
Workpiece N

Fmn
S
N S
Abrasive Media
Chip Abrasive
Fc Workpiece

Workpiece Workpiece
fixture
Fn Workpiece Motion
Ft surface CIP Chain

MRF CMP MFP

Spindle
Drive
Shaft

Magnetic
Fluid &
Abrasives

Ceramic balls

Float Al Base
NS N S N S
Steel yoke
S NS NS N
82
Magnets
 OVERVIEW OF
ADVANCED ABRASIVE FINISHING
PROCESSES

83
WHY ADVANCED ABRASIVE FINISHING
PROCESSES?

Complex Geometrical Shapes.

Labor Intensive Nature of Traditional Finishing Operations.
Difficulties in Controlling Abrading Forces.
Nano-meter (10-9 m) Surface Finish Requirements.

84
ADVANCED ABRASIVE FINISHING PROCESSES

MAF Magnetic Abrasive Finishing

AFF Abrasive Flow Finishing
MRAFF Magnetorheological Abrasive Flow Finishing
MRF Magneto Rheological Finishing
CMP Chemo Mechanical Polishing
MFP Magnetic Float Polishing

IN ALL THESE PROCESSES NORMAL FORCE IS RESPONSIBLE FOR PENETRATION OF ABRASIVE

INTO WORKPIECE AND SHEAR FORCE TO REMOVE THE MATERIAL IN THE FORM OF MICROCHIP

85
86
 SCHEMATIC VIEW OF MAF WORKING PRINCIPLE

WORKING GAP FILLED WITH MAPs FORMS FMAB

MULTIPOINT CUTTING TOOL

Magnetic
Rotating equipotential lines Magnetic
magnetic pole lines of
force
Flexible Magnetic Workpiece MAPs formed
Abrasive Brush FMAB N Fmn
Finished Surface N Abrasive
Micro
Fc
Chip

Workpiece Workpiece
S
S

Feed

SALIENT FEATURES
Ra = AS GOOD AS 8 nm 87
 MAGNETIC ABRASIVE FINISHING (MAF)
(DST SPONSORED PROJECT)

EXPERIMENTAL SET-UP
DIGITAL PHOTOGRAPH OF FLEXIBLE
MAGNETIC ABRASIVE BRUSH (FMAB)

ROUND ELECTROMAGNET

FMAB
FERROMAGNETIC
WORKPIECE

DESIGNED AND FABRICATED AT IITK

88
 EXPERIMENTAL RESULTS OF MAF
Surface Profilometer Results
DC-MAF

I=0.88 A, Before MAF

G= 500
N=11
(No. of cycles) After MAF

Before MAF

I=0.75 A,
G=600
N=9
After MAF
I=0.75 A,
G =800
N= 9 After MAF
89
BEST SURFACE ROUGHNESS ACHIEVED WAS 40nm
MICRO DEBURRING APPLICATION OF MAF

(a) (b)
Drilled hole edge (a) before, (b) after deburring

90
ABRASIVE FLOW FINISHING
(AFF)

91
 ABRASIVE FLOW MACHINING (AFM)
Two vertically opposed cylinders extrude abrasive laden medium
back & forth through passage formed by the workpiece &
tooling
Medium : Visco-elastic Polymer with Fine Abrasive
special rheological properties Particles

Abrasive Flow Machining (AFM) at IIT K

(DST SPONSORED PROJECT)

Deburring of
turbine impeller

92
Fig: Abrasive flow finishing setup for knee joint finishing

Piston
Silly Putty (viscoelastic) + SiC
(abrasive)
Workpiece held in fixture

Thermostat for temp control

 KEY FEATURES OF AFM

VERSATILITY FINISH COMPLEX SURFACES OF VARIOUS SIZES.

0.1 m to 0.05 m Ra.

SURFACE FINISH -
FORCE : 0.0009N -- 0.002N Per Particle
DEPTH OF PENETRATION : 5nm -- 30nm

LIMITATIONS:

VISCOELASTIC POLYMERIC MEDIUM COSTLY AND LACK OF

AVAILABILITY.
MEDIUM RHEOLOGICAL PROPERTIES VARY IN
UNCONTROLLED MANNER DURING PROCESS.
LACK OF DETERMINISM.

94
 AFM MEDIA ACTS AS A
SELF-DEFORMABLE STONE

95
MAGNETORHEOLOGICAL
FINISHING
(MRF)

96
 MRF- Mechanism of material removal
CI particles form a chain-like columnar structure, with the
application of magnetic field and they are aligned along the lines of
magnetic force.
The magnetic force between iron particles provides bonding strength
to it.
When these chains have relative motion
with respect to the workpiece surface
the asperities on the surface are abraded
due to shearing / plastic deformation at
the tips.

Source: www. qedmrf.com

 MAGNETORHEOLOGICAL FINISHING (MRF)
Fluid is extruded onto a rotating wheel in a thin ribbon that
contacts the optical / WORKPIECE surface.
Electromagnet below the polishing wheel exerts a strong local
Magnetic field gradient.
Precisely controlled zone of magnetized fluid becomes the
Polishing tool.

MR-fluids are suspension of

ferromagnetic particles in water/oil
that reversibly stiffens under the
influence of magnetic field.

Stiffness of the fluid Magnetic

Field Strength.
98
 Apparatus and tooling for freeform surface

(1- CNC milling M/c head, 2- MR finishing

tool, 3- MR polishing fluid, 4- fixture for knee
joint implant (Ti6Al4V), 5- knee joint implant)

99
 Finishing of freeform surface
Knee joint implants consist of metal femoral and tibial components with a
plastic polyethylene insert sandwiched between to restore joint function.
Surface roughness of knee joint implant has a significant effect on the
force at the connection and reaction of tissues in the joint area and
behaviour of germs in bone tissue (Mathia et al., 2011).
Wear by abrasion is one of the main causes for failures of knee joints
because over time, the continuous movement between the metal and plastic
can cause the polyethylene to crack, pit and delaminate.
It may also cause
microscopic particles to
break off which in turn
attack the bodys
immune system.

Components of knee joint implants (Courtesy: Aesculap Implant Systems, LLC,

100
www.soactivesofast.com).
MRF EXPERIEMTNAL SETUP AT IIT - K
(BY B. TECH. STUDENTS PROJECT)

MR FLUID WORKPIECE / LENS

101
 EXPERIMENTAL RESULTS OF MRF

53 nm (RMS)
Before
20 mins 30 mins
finishing

40 mins
50 mins

11 nm (RMS)

102
THANK YOU

103
IBM EBM LBM

SHORT PULSE LASER MACHINING

Ref.: Cmxr lasers industry,
www.cmxr.com/industrial/handbook/
 MECHANISM OF MATERIAL REMOVAL IN MECHANICAL MICROMACHINING

ABRASIVE WATR JET MACHINING ULTRASONIC MACHINING

ABRASIVE JET MACHINING

AWJM, AJM, USM

Mechanism of material Mechanism of material removal in
removal in ductile material brittle material

FORCES ACTING ON EACH PARTICLE AND PARTICLE SIZE

WILL DEC IDE THE SCALE OF MATERIAL REMOVED :
MACRO, MICRO, NANO

105
 MAF AFM MRAFF
FLEXIBLE MAGNETIC
Magnetic
ABRASIVE BRUSH
lines of
force
N
Workpiece

S
Fmn
Abrasive Media
Chip Abrasive
Fc Workpiece

Workpiece

Fn
Ft

MRF CMP MFP

Spindle
Drive
Shaft

Magnetic
Fluid &
Abrasives

Ceramic balls

Float Al Base
ABRASIVE
NS N S N S
Steel yoke
S NS NS N
Dr. V.K.Jain, I.I.T. Kanpur;[email protected] 106
Magnets
ADVANCED MACHINING PROCESSES

Prof. V.K.Jain, Mechanical Engineering

107
Department, I.I.T. Kanpur
 QUESTIONS BANK

Questions bank for introduction to AMPs

Q.1 Name the important factors that should be considered during the selection of an Advanced Machining Process for a
given job.
Q.2 Classify the different types of Advanced Machining Processes based on different criteria.
Q.3 What do you understand by the term Micromachining? Classify the different types of micromachining methods. Also
write down the ranges of macro, meso, micro, and Nano machining.
Q.4 What do you understand by hybrid process? List out the names of hybrid processes and the advantages of a hybrid
process over its constituent processes.
Q.5 Classify the advanced machining processes based on electrical properties of materials.
Q.6 what is the mechanism of material removal in Laser beam machining?
Q.7 Differentiate between chemical and electrochemical machining processes.
Q.8 Write the element of EBM.
Q.9 what do you understand by a finishing process?
Q.10 what are the constraints that limit the performance of different kinds of AMPs
Q.11 what do you understand by the word unconventional in unconventional machining processes ? Is it justified to use
this word in the context of the present day medium and large scale engineering industries?
Q.12 Classify the advanced machining processes on the basis of type of the energy employed.
Q.13 What are the advanced machining processes which can be used for magnetic material?

Prof. V.K.Jain, Mechanical Engineering

108
Department, I.I.T. Kanpur
 BASICS OF EDMM

IN EDM MATERIAL IS REMOVED BY THE THERMAL EROSIVE ACTION OF ELECTRICAL

DISCHARGES (SPARKS) PROVIDED BY THE OF A PULSE GENERATOR.

THE SAME PRINCIPLE OF

EDM IS APPLIED TO REMOVE
MTERIAL AT MICRON LEVEL
FOR MICROMACHINING.

IN MICRO-EDM, THE KEY IS

TO LIMIT THE ENERGY IN THE
DISCHARGE (SPARK)

109
 PROCESS CHARACTERSTICS

PROPERTY VALUE
MECHANISM OF MATERIAL REMOVAL MELTING, VAPORIZATION

MEDIUM VACUUM

TOOL BEAM OF ELECTRON MOVING AT VERY HIGH SPEED

MAX. MRR 10 mm3/min (MAY BE IN SPECIAL CONDITIONS)

SPECIFIC POWER CONSUMPTION 450 W/mm3-min

CRITICAL PARAMETERS ACCELERATING VOLTAGE, BEAM CURRENT, BEAM DIA.,

WORK SPEED, MELTING TEMPERATURE

MATERIALS APPLICATION ALL MATERIALS (CONDUCTIN & NON-CONDUCTING

BOTH)
SHAPE APPLICATION DRILLING FINE HOLES, CUTTING CONTOURS IN SHEETS,
CUTTING NARROW SLOTS
LIMITATIONS VERY HIGH SPECIFIC ENERGY CONSUMPTION,
NECESSITY OF VACUUM, EXPENSIVE MACHINE

110
E-BEAM WELDING

SUS >> SULPHUR STEEL

111
 Micro / nano finishing

traditional Advanced
Grinding AFM

Lapping MAF

Honing MRF

CMP

MRAFF

ELID

MFP

112