F2300 Digital Control Incise Machine System Manual

FangLing Digital Control

Incise Machine System Manual

(Model : F2300)

ShangHai JiaoYi NC Equipment Co., Ltd.

1
F2300 Digital Control Incise Machine System Manual

2
 F2300 Digital Control Incise Machine System Manual

REVISION HISTORY

Version Date Description

V2.3-Pre-Spec.01 2009.12.01 New manual creation
V2.3-Spec.02 2011.06.18 Update Chapter 11

3
F2300 Digital Control Incise Machine System Manual

4
 F2300 Digital Control Incise Machine System Manual

User Guide
Read This Manual

This manual is used to the digital control incise machine system (F2300) produced by

Shanghai JiaoYi NC Equipment Co., Ltd.

Read and understand this instructional manual, the cutting machine manuals, and your

employers safety practices. Note: This product is not designed to be field serviceable. Please

return back to an authorized repair center for any required service.

Shanghai JiaoYi NC Equipment Co., Ltd. after-sale service center:

Address: Room 201, NO.609, Rd. Ziri, Zizhu Technology Park, MinHang, ShangHai, China

Tel: 021-34290910 34290970

Fax: 021-34290970

E-mail: [email protected]

Website: www.flcnc.com

Work Condition

Working Temperature, -10-60. Relative Humidity, 0-85%.

Operation Voltage, DC 24V.

The controller should be installed in a cab which can provide protection from powder.

The controller would be better used in the situation without high voltage radiation.

Maintenance

KEEP HANDS CLEAR of dangerous moving machinery. All control action, including

manual action, can be executed using the front panel keys or remote interface.

5
 F2300 Digital Control Incise Machine System Manual

Loose fitting clothing or ties may become entangled in the machinery. These items should

not be worn while operating the machine.

This controller should only be operated by trained service person.

Do not open the controller unless obtaining the authorization.

Do not let any acid or alkalescent substance to corrode the controller.

High Voltages

Electric shock can kill. Be sure this equipment is safely installed in accordance with enclosed

procedures and specifications.

Avoid contact with electrical wires and cabling while power is on.

Only trained person can operate this controller.

6
 F2300 Digital Control Incise Machine System Manual

Catalog
FANGLING DIGITAL CONTROL INCISE MACHINE SYSTEM MANUAL................................... 1

USER GUIDE...........................................................................................................................................5

READ THIS MANUAL..............................................................................................................................5

WORK CONDITION..................................................................................................................................5
MAINTENANCE....................................................................................................................................... 5
HIGH VOLTAGES..................................................................................................................................... 6

CHAPTER 1 SUMMARIZE.................................................................................................................1

1.1 BRIEF INTRODUCTION...............................................................................................................1

1.2 CHARACTERISTICS OF SYSTEM.............................................................................................. 1
1.3 TECHNICAL STANDARD............................................................................................................ 3
1.4 SYSTEM INTERFACE...................................................................................................................3
1.5 HARDWARE CONFIGURATION................................................................................................. 3

CHAPTER 2 SYSTEM BOARD AND MAIN INTERFACE............................................................ 4

2.1 INTRODUCTION OF OPERATING BOARD...............................................................................4

2.2 POWER ON PROCESS AND MAIN INTERFACE...................................................................... 4
2.3 FUNCTION INDEX OF MAIN INTERFACE.............................................................................................7

CHAPTER 3 CUTTING FUNCTION................................................................................................. 9

3.1 CUTTING OPERATION INDEX.......................................................................................................... 11

3.2 SPEED REGULATION....................................................................................................................... 12
3.3 FORWARD........................................................................................................................................12
3.4 BACKWARD.....................................................................................................................................12
3.5 EDGE CUTTING / OFFSET CUTTING / RETURN................................................................................13
3.6 BACK TO REFERENCE FUNCTION................................................................................................... 14
3.7 OXYGEN GAS PREHEAT TIME REGULATION................................................................................... 15
3.8 PERFORATION POINT SELECTION....................................................................................................16
3.9 DYNAMIC AMPLIFICATION..............................................................................................................17
3.10 CUTTING EXIT.............................................................................................................................. 17

CHAPTER4 PART OPTIONS............................................................................................................. 19

4.1 XY MIRROR.................................................................................................................................... 19
4.2 ANGLE ADJUSTMENT...................................................................................................................... 20
4.3 ARRAY............................................................................................................................................ 21
4.4 ZOOM IN/OUT................................................................................................................................. 25
4.5 SELECT ROW/NUMBER.................................................................................................................... 26
4.5.1 Select row.............................................................................................................. 27
4.5.2 select number........................................................................................................29
4.5.3 operation after select row/number.....................................................................29
4.6 RESTORE.........................................................................................................................................30
7
 F2300 Digital Control Incise Machine System Manual

CHAPTER 5 MANUAL FUNCTION................................................................................................31

5.1 FIXED MOVING FUNCTION............................................................................................................. 31

5.2 CONTINUOUS MOVING FUNCTION..................................................................................................32
5.3 FIXED-LENGTH MOVING................................................................................................................. 32
5.4 BREAKPOINT RECOVERY................................................................................................................ 32

CHAPTER 6 FILE OPERATION....................................................................................................34

6.1 FILES IN THE HARD DISK............................................................................................................... 34

6.2 FILES IN THE U DISK......................................................................................................................35
6.3 SEARCH FILE.................................................................................................................................. 37
6.4 EDIT CODE..................................................................................................................................... 37
6.5 NEW CODE..................................................................................................................................... 38
6.6 COMPILE CODE...............................................................................................................................38

CHAPTER 7 PARAMETER SETTING........................................................................................... 39

7.1 COMMON PARAMETERS.................................................................................................................. 39

7.2 FLAME PARAMETERS......................................................................................................................40
7.3 PLASMA PARAMETERS.................................................................................................................... 42
7.4 POWDER PARAMETERS................................................................................................................... 43
7.5 SYSTEM PARAMETERS.................................................................................................................... 44
7.6 PARAMETER IMPORT....................................................................................................................... 46
7.7 PARAMETER EXPORT.......................................................................................................................47
7.8 SAVE PARAMETERS......................................................................................................................... 47

CHAPTER 8 DIAGNOSIS FUNCTION...........................................................................................49

8.1 DIAGNOSIS INTERFACE INDEX........................................................................................................ 50

8.2 INPUT DIAGNOSIS........................................................................................................................... 50
8.3 OUTPUT DIAGNOSIS........................................................................................................................ 50
8.4 KEY-PRESS DIAGNOSIS................................................................................................................... 51
8.5 SYSTEM SELF-CHECK......................................................................................................................52
8.6 DATE AND TIME...............................................................................................................................53
8.7 SYSTEM DEFINITION.......................................................................................................................54
8.7.1 Parameter backup and restore.......................................................................... 54
8.7.2 Input definition.......................................................................................................55
8.7.3 Output definition................................................................................................... 55
8.7.4 Coordinate definition............................................................................................56

CHAPTER 9 GRAPH...................................................................................................................... 58

9.1 CHOOSE GRAPH..............................................................................................................................58

9.2 FILM/HOLE SIZE.............................................................................................................................59

CHAPTER 10 PORT EXPLANATION............................................................................................ 61

10.1 INPUT PORT...................................................................................................................................61

10.1.1 Input Wiring Instructions................................................................................... 63
10.1.2 Remote Input...................................................................................................... 64

8
 F2300 Digital Control Incise Machine System Manual

10.1.3 Input Configuration.............................................................................................65

10.2 OUTPUT PORT...............................................................................................................................66
10.2.1 Output Wiring Instructions................................................................................ 67
10.2.2 Output configuration.......................................................................................... 72
10.3 MOTOR PORT................................................................................................................................73
10.3.1 Typical wiring diagram of the electrical motor interfaces............................ 74
10.3.2 Coordinate Mapping.......................................................................................... 78

CHAPTER11 INSTALLATION AND DEBUGGING......................................................................79

11.1 HORIZONTAL / VERTICAL PULSES NUMBER SETTING.................................................................... 79

CHAPTER12 THE USE OF BIOS...................................................................................................80

12.1 SYSTEM UPGRADE........................................................................................................................ 81

12.2 WELCOME INTERFACE UPGRADING.............................................................................................. 81
12.3 MOVEMENT CONTROL UPGRADE.................................................................................................. 81
12.4 MOVEMENT BACKUP....................................................................................................................81
12.5 SYSTEM RESET............................................................................................................................. 81

APPENDIX 1 GM CODE RAPID CONSULT............................................................................. 82

9
F2300 Digital Control Incise Machine System Manual

10
 F2300 Digital Control Incise Machine System Manual

CHAPTER 1 SUMMARIZE

1.1 BRIEF INTRODUCTION

The digital controller F2300 is a new production, which is integrated many merits of the
same productions at home and aboard. The controller can control the motion of two axis, which is
apt to the application of flame or plasma cutting. This controller is very light and handy and it is
very easy to operate. The controller provides menu or illustration for all the operations for the
convenience of users. All key switches are human oriented designed, and they are very convenient
and comfortable.
The controller chooses high speed DSP and ARM as its core to assure the cutting process to
be more stable. The motion control algorithm is optimized so that the machine can move more
stale and reliable, and it can save the life of the motor and the mechanical parts.
The controller use the LCD graphic display, supporting the TTL interface and VGA interface,
and the max resolution is 800*600. The controller has two kind of configuration shown as follows:

Fig 1.1 F2300A Fig1.2 F2300B

1.2 CHARACTERISTICS OF SYSTEM

1 10.4 inches 800*600 dots color LCD.

2 Chinese/English file system and menu, and the menu can be switched only by one key.
3 45 categories different graphics (including grid pattern), chip part and hole part are
alternative.
1
 F2300 Digital Control Incise Machine System Manual

4 Support the EIA code (G code) ESSI Code and various FastCAMFreeNestSmartNest
IBE softwares.
5) compact keyboard design and easy to input files.
6 Graphics have some operations such as Proportion, Rotate, Mirror.
7 Graphics can be arrayed in matrix, interaction, stacked modes.
8 Steel plate can be adjusted according any steel side.
9 Coordinate system can be customized to support the two-dimensional coordinates of all
eight kinds.
10 All input and output port type and the number can be customized (normally open or
normally closed)
11) Self-diagnostic function, to diagnose the key status and all the IO status, facilitate
inspection and debug
12 Provide a front USB interface for copying files.
13 system can be upgraded by USB interface easily, and we provide lifetime free upgrade
service.
14) all functions and techniques can upgrade online and dont worry about the after sale
service.
15 Import and export files by single or all files.
16) Display time, week and clock.
17) Parameters backup and online upgrade.
18) Support the Flame, Plasma, Dusting draw and Demonstration four kinds of mode.
19) Including various types of processing parameters to meet the needs of different
processes.
20) Flame and Plasma are separated in the control IO ports.
21) Support THC, two level preheat, three level pierce in flame mode.
22) Plasma arc feedback, positioning feedback, automatically shut down the arc at the
corner.
23) Support edge cutting. It can save the preheat time for the thick steel plate.
24 Movement speed can be real-time acceleration, deceleration.
25 According to plate thickness, the cutting speed is automatically restricted by a speed limit
in the corner, effectively preventing over burn.
26select row and column manually.
27 Dynamic/static illustration of the process, graphics zoom in / out, dynamically tracking
cut-off point under zooming state.
28DSP as core can control the machine move in high speed accurately, stability and in low
noise.
29Starting speed and acceleration can be set by your convenience.
30Automatically memorize the working situation and the last cutting point when power off.
31 "Cutting offset" function can avoid waste the steel plate when the nesting of the plate is
calculated wrong.
32set up different administration authority and the corresponding password to safeguard the
interests of managers.
33 Long-distance remote control can control the machine to move forward ,backward, left,
right and cutting start, stop and so on (optional configuration).

2
 F2300 Digital Control Incise Machine System Manual

1.3 TECHNICAL STANDARD

1 Control Axis2
2 Control accuracy +/-0.001mm
3 Coordinate range+/- 99999.999mm
4 Max pulses : 200kHz Max speed15000 mm/m
5 Max lines of code10000lines
6 Max size of single code file1M
7 Time resolution 10ms
8 Working Voltage DC 24V in put
9 Working Temperature-10-60. Relative Humidity, 0-95%.

1.4 SYSTEM INTERFACE

1) 15 pins interface of 2 axis of motor drive.

2) 25 pins interface of 16 channels optical couple output portsmax back flow current 300mA.
3) 25 pins interface of 16 channels optical couple input portsmax output current 300mA.
4) USB interface on the front panel.
5) Extend IO input/output ports, PWM input ports, analog input ports.

1.5 HARDWARE CONFIGURATION

1) Monitor: 10.4 inch 800*600, high definition 16 million colors and high brightness LCD.
2) Memory: 64M SDRAM
3) Memory available for user: 256M or 1G electronic hard disk
4) System master frequency: 400MHz
5) USB: USB 1.1 front interface
6) Keyboard: electronic PCB foil keyboard( one machine) or standard industrial
keyboard(split type machine)
7) Chassis: full-steel structure completely shielded which defends electromagnetic radiation,
interference and static electricity.

3
 F2300 Digital Control Incise Machine System Manual

CHAPTER 2 SYSTEM BOARD AND MAIN INTERFACE

2.1 INTRODUCTION OF OPERATING BOARD

Fig 2.1 board and keys

F1-F8 Function key in different interface

S/PgUP page-up key of code interface or Torch up in other interface
S/PgDn page-down key of code interface or Torch down in other interface
F/HOME Accelerate or skip to the head of code line
F/END Decelerate or skip to the tail of code line
1-9 during the cutting process, change the cutting speed to ratio of the speed limit
you have set, for example press 1, change the cutting speed to 10% of the
speed limit you have set, press 2, change the cutting speed to 20% of the
speed limit you have set

2.2 POWER ON PROCESS AND MAIN INTERFACE

When power just on, the system will go for the process of self scan

4
 F2300 Digital Control Incise Machine System Manual

Fig 2.2 system self scan

In the starting process, there is 3 seconds to countdown, before the countdown is over, if
pressing F2, it will enter the bios starting interface shown as Fig2.3 (please take the reference
of the appendix 2 to run bios). If pressing any other key, it will jump over the countdown and
directly enter the welcome interface. If pressing no key, it will countdown to 0 and then enter the
welcome interface shown as Fig2.4.

F1 - (System software update)

F2 - (Welcome picture update)
F3 - (Motion update)
F4 - (System backup)
F5 - (System recovery)
F6 - (Start system)

Fig 2.3 bios interface

5
 F2300 Digital Control Incise Machine System Manual

Fig 2.4 bios interface

In the welcome interface, press any key to enter the main interface automatically shown as Fig2.5:

Fig 2.5 the main interface

6
 F2300 Digital Control Incise Machine System Manual

In the main interface, press F1-F8for the following functions

F1ShapeLib: pressing F1 to enter the Shape Library including 45 common shape, and most
of them have plate size and hole size.
F2Files: You can load local files, U disk files or edit, import, export and delete codes.
F3PartOption: make actions of mirroring, rotation, plate adjusting, plate arraying, selecting
row and hole or code edition etc.
F4Setups: setting all parameters.
F5 Diagnose: including input ports diagnosis, output ports diagnosis, keyboard diagnosis,
system self check, date setting and system self defines.
F6ZoomIn: Zoom in the shape in full screen.
F7ManualMove: Manually move the machine.
F8Zero: Clear the coordinate of X and Y before starting cut or after cutting over.
XCutSpeed: Setting the cutting speed.
YManualSpeed: Setting the manual moving speed.
Z Kerf: Setting the kerfs compensate value.
F Manual: Setting the mode of manual movement including keepMov(keep movement),
StepMov(step movement), ContiMov(continue movement). The selected mode is black
background.
GStepDis: Setting the distance of the fixed-length.
MSelecting the cutting mode including Flame Cu(flame cutting), Plasma C(plasma cutting),
Demo run.

2.3 Function index of main interface

7
 F2300 Digital Control Incise Machine System Manual

Main
Interface

F1 F2 F3 F4 F5 F6 F7 F8
ShapeLib Files Part Setups Diagnose Zoom In Manual Zero
Option Move

F1 F1
F1 F1 F1
Input keep
Disk File Mirror common
Diagnose moving

F2 F2
F2 F2 F2
Output continue
U Disk Angle Flame
Diagnose moving

F3 F3
F3 F3 F3
Open step
Search Array Plasma
Output moving

F4
F4 F4 F4 F4
Close
Edit File Scale Powder Speed-Down
Output

F5 F5
F5
F5 Select F5 Speed
Keyboard
Del File line and System accelarati
Diagnose
pierce on

F6 F6
F6
Import System
Copy to U
Parameters Self-check

F7
F7 F7 F7 F7
Export
Preview Revert Date time Recovery
Parameters

F8
F8 F8 F8 F8
System
OK OK OK Save
Definition

F1 F2
Parameter Parameter F3 F4 F5 F6
Definition Encryption Decryption Language F8 Update
Recovery Backup

F1
Input

F2
Output

F3
Coordinate

F8
Save

8
 F2300 Digital Control Incise Machine System Manual

CHAPTER 3 CUTTING FUNCTION

In the main interface, press the SPACEto enter the cutting interface, shown as follows:

Fig 3.1 cutting function interface

Show the current workpiece's cutting path, including the slotted value.
Show the G-code being processed, shows the current and next line.
Show the current cutting speed, during processing, you can press the keyboard's number keys
1 - 9 to achieve quick speed regulation. For example, press the number3, the speed
is automatically adjusted to 30%; press the number 8 the speed is automatically adjusted to
80%.
X shows the absolute coordinate of the torch in X direction.
Y shows the absolute coordinate of the torch in Y direction.
In the cutting interface:
Press X: Modify the current maximum cutting speed.
Press Y: Modify the current maximum speed manual shift car.
Press F: Change the current manual method.
Press G: Modify the current fixed-length fixed long-distance move.
START(F9): Start cutting.
STOP(F10): Parking, the system can suspend all ongoing actions.
F1:The torch move back along the cutting path(I / O port closed)
9
 F2300 Digital Control Incise Machine System Manual

F2: The torch forward along the path (I / O port closed).

F3: Return to the starting point of cutting torch, i.e. the starting point of the current work
piece.
F4: Decrease the cutting speed, each decrease of 1% click rate.
F5: Increase the cutting speed, each 1% increase in click rate.
F6 : Reduce the preheat time, skip the remaining preheat time, and the system
automatically records preheat time.
F7: Increase the preheat time once 15 seconds.
F8 : When the system is suspended, for selecting perforation point; when the system
begins to move, for the dynamic amplification.
four direction keys (Up, down, left and right): When the gun through, manually move the
torch.

10
 F2300 Digital Control Incise Machine System Manual

3.1 Cutting Operation Index

Cutting
Interface

F1
Backward

F2 Forward

F3 Back to
reference

F4 Speed
Down

F5 Speed
Up

F6 Preheat
Down

F7 Preheat
Up

F8 Jump to
pierce

Automatic operation index

11
 F2300 Digital Control Incise Machine System Manual

3.2 Speed Regulation

3.2.1 Normal Speed Regulation

In automatic operation, or when the system is suspended, in the cutting interface the system
can regulate speed.
The operation panel, press F5 or PRE, increasing at a rate per click rate of 1%.Hold
the F5 or PRE, then the rate will continuously increase to 100%.Increased to 100%, the
speed is "common parameters" in the "cutting speed."
The operation panel, press F4 or NEXT, each click rate of speed reduced by 1%.Hold
the F4 or NEXT, then the rate will be continuously reduced to1%. Reduced to a very slow
speed when running in order to ensure the accuracy requirements, the system may auto-adjust the
speed based on the size of "horizontal pulses" and "vertical pulses", actual speed may not be the
"cutting speed" of 1% is greater than 1%.
3.2.2 Quick Speed Regulation
In automatic operation, or when the system is suspended, in the cutting interface the system
can carry out quick speed regulation.
In the cutting interface, on the operation panel, press the number keys 1 - 9, the speed
will quickly adjust to the corresponding percentage figures 10 times, for example press 3 ,
adjust to 30% of the speed limit you have set, press 8, adjust to 80% of the speed limit you
have set.

3.3 Forward

In the automatic function interface, press keyF1the machine start to move without real
cutting. The process does not include any ignition, perforation and any other I/O working. The
machine just moves the torch according to the graphic figure.
The function can be used to check the trail and code before you start the real cutting process,
or can also be used when the process needs through the gun. Press the red STOP key to stop the
null cutting process if you want.

3.4 Backward

During the running process, if you want to go backward according to the origin trail to
(maybe the iron board was not cut through), you can follow the following direction:
First, press STOP key to set the machine at pause status.
In the automatic function interface, press key F3 (Back) to make the machine go
backward along with the original trail. When the torch reaches the position you need, press
STOP key to stop it. You may press key F2 to go forward if the machine just went back too
much.
Notice: Go backward or forward function can be used repeatedly to make the machine reach
an ideal position.
When the torch reaches the position you need, press START key again, if the current
cutting code is G01, G02 or G03, system will automatically perforate before performing these
12
 F2300 Digital Control Incise Machine System Manual

procedures, and then continue the current program, if the current row is not G01, G02 or G03, the
system will directly continue the current line program.

3.5 Edge Cutting / Offset Cutting / Return

When the torch is not on the actual path of the current work piece, it will prompt as follows:

Fig. 3.2 edge perforation

There are two reasons led to this situation:
(1) When the common parameter "edge perforation" selects "Yes" and the next processing
line G-code is M07, the system will be automatically suspended. At this time, the torch can be
manually moved to any edge of the plate, press the "start" button, the system will prompt as above
(2) When the processing is paused, due to mechanical failure or other reasons, it needs to
move the torch out of the actual path of the workpiece, the above prompt will appear.
If press G, the system cutting returns back to the paused point, continue to cut it. This
feature is particularly useful for thick steel plate, it can reduce the preheat time and increase
cutting efficiency. This function is the commonly-used edge perforation function.
If pressX, the system considers current point is the paused point, it will continue cutting
it. That is, the system offsets the cutting point. When the cutting machine paused or a power
outage, if the cutting tip or steel plate with the pan has been offset, or the user would like to think
that is offset cutting, you can press this button.
If pressY, The system only return to the paused point quickly, and then break off. During
the cutting process, if discovery cutting torch malfunction, or other issues, need to move the
13
 F2300 Digital Control Incise Machine System Manual

cutting tip out of cutting region to overhaul. After the maintenance, this key can be pressed. Then
return to the paused point, press the "start" button, the system automatically continues to cutting.

3.6 Back to Reference Function

Pause in the processing, if press the F3, then the system will prompt:

Fig. 3.3 return reference prompt

Press the Enter key, the system will automatically return to the starting point of the work
piece, and then the system automatically switches to processing the main interface, and waits for
further user action.

14
 F2300 Digital Control Incise Machine System Manual

Fig. 3.4 main process interface

During the return process, the user can press the "Stop" button to stop the operation, and can
continue to return operation after pressing of F3. Number of back to reference and stop has no
limit.

3.7 Oxygen Gas Preheat Time Regulation

In the preheat process, press the START (F9) key to skip the process of preheat and
perforation delay, and immediately open the perforation signal then begin to cut.
In the preheat process, press the stop (F10) key to stop preheat, waiting for the F9 key is
pressed again.
In the preheat process, press the F6 key then the preheat time will be reduced to the current
preheat time spent, and skip the process of preheat and perforation delay, and open the perforation
signal then begin to cut..
For example: the original system sets the preheat time of 60 seconds after null cutting, when
preheat needed, the interface will count down, under normal circumstances, till 0, the system
begins the next step of cutting, but if the system has the remaining 10 seconds of countdown time,
press F6, then the system immediately stops preheat to begin the next step of cutting, and records
the preheat time of 50 seconds, the system automatically thinks that users need preheat time of 50
seconds, the next preheat after the null cutting when the preheat time becomes 50 seconds.
In the preheat process, each press the F7 key, preheat time increases by 15 seconds, and the
preheat time maintains the increased value.
15
 F2300 Digital Control Incise Machine System Manual

For example: The original system sets the preheat time of 60 seconds after the null cutting,
during the system countdown, each press F7, on the interface the countdown increases by 15
seconds, and the next time you need to preheat, the initial preheat time be 75 seconds.

3.8 Perforation Point Selection

Before you start cutting or cutting is paused, the function key prompt F8 is "select new
pierce", then press F8, the system will prompt:

Fig. 3.5 select new pierce

If you press ESC, the system will then return the cutting interface. If you press ENTER, the
system will again prompt:

16
 F2300 Digital Control Incise Machine System Manual

Fig. 3.6 pierce prompt

pierce point can be input manually at this time. You can also press ESC to exit without
manual input perforation point, and then press the left and right arrow keys to select the
perforation point.

3.9 Dynamic Amplification

After the start of cutting, the F8 in the cutting interface will become "dynamic amplification",
then press the F8 key, full-screen amplify the processing graphic , and dynamically tracking.

Press the F8 key continuously, the system will progressively amplify graphic.
Press ESC to exit the amplified display, back to the cutting interface.

3.10 Cutting Exit

When the cutting operation does not get finished, and the cutting machine also being in the
pause condition, if press Esc , the system will query whether quit the cutting operation. If
pressing Enter, the system will exit, and if pressing Escthe system will not exit, get into the
automatically interface and go on with the cutting operation at the current place.
17
F2300 Digital Control Incise Machine System Manual

Fig. 3.7 Quit of cutting

18
 F2300 Digital Control Incise Machine System Manual

CHAPTER4 PART OPTIONS

Before starting cutting, you can use F3 PartOption in the main interface. Press F3 to enter part
options menu

Fig 4.1 Part options

4.1 XY mirror

Press F1, the system will prompt:

Press F1 to mirror along the horizontal axis(X axis)

Press F2 to mirror along the vertical axis(Y axis)

19
 F2300 Digital Control Incise Machine System Manual

Press ESC to exit mirror operation

4.2 Angle adjustment

Press F2, the system will prompt:

Press F1 to adjust steel plate

Press F2 to enter angle directly
Press ESC to exit angle adjusting

4.2.1 Steel plate adjustment

After entering steel plate adjustment menu, the system will prompt:

Here, you can manually move the cutting tip to the edge of one side or a corner of the plate.
When the cutting tip moved to a good position, press X key to set the current point as the
starting point of correction.
And then manually move along the cutting tip, as long as moving to the edges of the side.
After ensuring the two points far enough and two points at the same side of the plate in the same
line and press Y. The system will automatically calculate the current offset angle of plate, and
then automatically rotate graphics.

Before adjusting After adjusting

After adjusting, the system will ask whether to return to the start point, if press [ENTER],the
system will back to the start point of the operation, if press [ESC], the system will do nothing but
20
 F2300 Digital Control Incise Machine System Manual

go back to the graphic interface.

Fig 4.2 Return to the start point after adjusting

4.2.2 Enter angle
When the angle of the current work piece is known, you can enter the angle:

Enter angle
After manually enter the angle, press [ENTER] to make sure, the graphic will be rotate with the
corresponding angle. Positive angle means rotate in counterclockwise, while negative means
clockwise. Press [ESC] to exit angle adjusting.

4.3 Array

In the part options menu, press [F3], the system will prompt as Fig 4.3, there are three ways to
arrange, arrange in matrix, staggered arrange, arrange in stack.

21
 F2300 Digital Control Incise Machine System Manual

Fig 4.3 chooses arrange method

Press [F1] to carry on arranging in matrix:

Fig 4.4 arrange in matrix

22
 F2300 Digital Control Incise Machine System Manual

The result is shown in fig 4.5

Fig 4.5 result of arranging in matrix

Press [F2] to enter staggered arrangement:

Fig 4.6 staggered arrange

23
 F2300 Digital Control Incise Machine System Manual

The result is shown in figure 4.7:

Fig 4.7 result of staggered arrangement

Press [F3] to enter arrangement in stack:

Fig 4.8 arrange in Nest

24
 F2300 Digital Control Incise Machine System Manual

The result is shown in figure 4.9:

Fig 4.9 result of arrangement in nest

4.4 Zoom in/out

In the part options menu, press [F4] (zoom in/out),the system prompt as figure 4.10:

25
 F2300 Digital Control Incise Machine System Manual

Fig 4.10 set scale

After entering the scale, press [Enter], then the system will automatically zoom in or zoom out the
graphic when the parameter is checked to be correct.

4.5 Select row/number

In part options menu, press [F5]to enter selecting row/number, the system will prompt:

26
 F2300 Digital Control Incise Machine System Manual

Fig 4.11 select Line/Pierce

4.5.1 Select row

Press [F1] to select the number of row to start cutting with, the system prompts:

27
 F2300 Digital Control Incise Machine System Manual

Fig 4.12 prompt to select row

Here , you can directly enter the row number or press ENTER to enter the interface and press
orto select row.

Fig 4.13 select row

28
 F2300 Digital Control Incise Machine System Manual

After selecting row, press F8 to confirm.

4.5.2 select number

The operation is similar to the choosing row operation.

4.5.3 operation after select row/number

After selecting row or number, press F8 continuously to exit to the main interface. Press SPACE to
enter the cutting interface, there are two kind of operation:
1 move from current position to the new position and then cutting
Press F1 in the cutting interface, the system will directly run to the position of the
selected row or number without cutting, then pause and wait for the next operation.

Press START in the cutting interface, the system will prompt:

Fig 4.14 operation after selecting row/number

Press Y , the system will also directly move to the selected row and number, then pause
and wait for the next operation.
29
 F2300 Digital Control Incise Machine System Manual

2 Cutting from the current position

After the prompt of Fig 4.14, press X, then the system will start cutting from current
position.

4.6 Restore

If you want to cancel all of operations with graphics including mirror, rotation, adjust, scale
and array, press [F7] in the part options menu, the system automatically revert to original state of
the graphics.

30
 F2300 Digital Control Incise Machine System Manual

CHAPTER 5 MANUAL FUNCTION

In the automatic interface, press F7(Manual) to enter manual function interface, shown as
Fig 5.1:

Fig 5.1 manual function interface

The speed in the manual status is controlled by the manual moving parameters. During the
process of fixed moving function, you can adjust speed by acceleration or deceleration key. In the
manual interface, press numeric key, the cutting speed changes to ratio which is 10 times of the
corresponding figure of the speed limit you have set, for example press 3, change the cutting
speed to 30% of the speed limit you have set, press 8, change the cutting speed to 80% of the
speed limit you have set.

5.1 Fixed Moving Function

When you enter into the manual interface, the default option is continuous moving function.
Press key F1 to go for the fixed moving function. At this moment, the system will move
toward the specified direction if any directory key is pressed, and when the directory key is
released, the system will stop.

31
 F2300 Digital Control Incise Machine System Manual

5.2 Continuous Moving Function

When in the manual interface, press F2 to enter the continuous-moving function interface. At
this moment, the system will move toward the specified direction if any directory key is pressed
and then released, and when the directory key or stop key is pressed the system will stop.

5.3 Fixed-length moving

In the manual interface, press F3 to enter the interface of fixed-length moving,. The system
prompts to input the fixed length:

Fig 5.2 Input the fixed length

After inputting the fixed length, press ENTER. Press any direction key and then release, the
system will move the fixed length toward the direction, in the process of moving, when any
direction key or stop key is pressed, the system will stop moving.

5.4 Breakpoint Recovery

To guarantee that the breakpoint could work correctly, you need to satisfy the following
conditions:
1. When the system is paused, the system will automatically regard the paused point as the current
breakpoint and remember it.
32
 F2300 Digital Control Incise Machine System Manual

2. When the system is in the process of incising, the breakpoint signal is connected with the urgent
alarm input, when power is off, the system will regard the power-off point as the breakpoint and
remember it.
When you need to process after the breakpoint, after the system powers on, dont move the
torch, press F7 in the main interface to enter the manual function interface, then press F7 to
recover the breakpoint. After recovering it, if the torch hadnt been moved and is on the position
when the power is off, press START keyboard, the system will process directly.
After the breakpoint is recovered, if the position is off from the original one, you could move
the torch to the original point manually, or realizing it through choosing rows or numbers. (Please
refer to chapter 4.5 Row and number Selection). The method is : choose stopping incising, move
the torch to the original point manually, choose the nearest row through choosing the row
selection(or number selection), press START, then the system will show in Fig 5.3:

Fig 5.3 restore breakpoint

Press G, the system will start incising from point which is after moving, and after
returning to the position before the torch moves, it will process according to the normal
curve.
Press X, regarding the position after moving as the position before moving, and then
process.
Press Y, move from the position after moving to the position before moving, then wait
for the next operation.

33
 F2300 Digital Control Incise Machine System Manual

Chapter 6 File Operation

The system supports cutting code which has txt and CNC postfix. And the maximum capacity
is 1M, the largest number of rows is 10000 lines. You can edit, compile, delete, export internal
document, also you can import the file in the U disk into system.
In the main interface, press keyF2(code) to enter local machine code interface, shown as
follows:

Fig 6.1 code interface

6.1 Files in the Hard Disk

In the file manage interface, press F1 to enter the hardware file list, as shown in Fig 6.1 the
system only lists the folder, TXT file and CNC file.
Press F4, if the current position of the cursor is txt file or cnc file, you could edit them.
Please refer to chapter 6.5 on how to edit files.
Press F5, if the current position of the cursor is txt file or cnc file, you could delete them.
Press F6, if the current position of the cursor is txt file or cnc file, you could copy the
current file to the flash disk when it is connected to the USB interface.
Press F7, if the current position of the cursor is txt file or cnc file, you could preview the

34
 F2300 Digital Control Incise Machine System Manual

current graphic.

Fig 6.2 Graphic preview

Press F8, if the current position of the cursor is txt file or cnc file, you could import the
current file to the system, after importing, the system will return to the main interface.

6.2 Files in the U Disk

In the code interface, press keyF2to go for U Disk interface.

In the U Disk interface, choose the corresponding cutting code, press F6, the system will
save this code into the internal documents.
Notices: When you open a file on U disk , you must save it as the local machine code before
you start cutting. When saved the U disk documents, file name automatically memory, shown as
Fig 6.3:

35
 F2300 Digital Control Incise Machine System Manual

Fig 6.3 save U disk files

When input file name, if you do not want to change the file name, you can be directly press
Enter to save; or modify the file name and then press Enter to save. If the same named file
has already exited, the system prompts:

Fig 6.4 Replacement documents

If you want to replace the internal documents, press Enter key, if you want to change the
file name, press Esc, change the file name and then save.

36
 F2300 Digital Control Incise Machine System Manual

6.3 Search File

In the file manage interface, press keyF3to search a file. You can input all or part of the file
name, then press Enter, and the system will list all the files that include the input word or file
name.

Fig 6.5 search file

6.4 Edit Code

In the local machine code interface, move the cursor to the file that you want to edit, then
press F4to enter the edit interface.
When enter the characters, some keys are reuse keys. Press these keys directly, enter the low
Character on the button is active . If press both Shift and reuse keys, then upper character on
the button is actived.
When editing the code, press F2 can insert a new line after the current line, and press
F3 to delete the current line. Press F + Home key, the cursor automatically moved to the
first character of the current editing line, press the F-End, the cursor automatically moved to
last character of the current line.
Each edit line supports 128 characters maximum.
When you open a file on U disk or new a code file, you must save it as the local machine
code before you start cutting. Otherwise, you cannot make use of the breakpoint recovery function
or power off protection function.
After edit the code , press F8to save the code.

37
 F2300 Digital Control Incise Machine System Manual

6.5 New Code

In the editing code interface (reference 6.4 edit code ), you can press keyF4to create an
new file to input your own code, shown as Fig 6.5.

Fig 6.6 new code

6.6 Compile Code

After create a new code or edit the code, if you want to know the code is valid or not , in the
edit interface, press F1 ,you can compile code to check whether the code is correct.

38
 F2300 Digital Control Incise Machine System Manual

Chapter 7 Parameter Setting

In the main interface, you can get the parameter interface by pressing keyF3(Para). The
parameter function interface is showed in Fig 7.1

Fig7.1 Parameter Interface

You can set five kinds of parameter in the parameter interface:
1) Common parameters: cutting speed, manual move speed, G00 move speed, the size of kerf
gap, corner speed, cutting type, edge cut enable, hold preheat.
2) Flame parameters: all the parameters used in oxygen gas cutting
3) Plasma parameters: all the parameters used in plasma cutting
4) Maring parameters: ignition, perforation cycle parameters, dry dusting offset
5) System parameters: you can set system pulses, maximum speed limit, motor parameters and
soft limit parameters.

7.1 Common parameters

It is the favorites parameters in Fig7.1.

Cutting Speed: the maximum cutting speed, unit is mm/m.

39
 F2300 Digital Control Incise Machine System Manual

Manual Move Speed: the moving speed of cutting torch in manual, unit is mm/m.
G00 Move Speed: the cutting torch speed when G00 is executed or the cutting torch go

back to the reference or some other occasion, unit is mm/m.

Kerf: According to the cutting gap width, users set Kerf Gap compensation(the value should

be half of the cutting gap ) to ensure the dimensional precision, the system will generate a
new path automatically to make compensation to work piece. Before cutting a work piece,
you can modify kerf gap value, once begin to cut, you are not permitted to modify the value.
Corner speed: Plate thickness affect the cutting tips ac/dc rate when it moving. The angle

between the end of a cut-point lines tangential direction and the direction of the tangent line
of the beginning of next cutting point, and the thickness of plate determines cutting tip speed
at the transition.
If the normal cutting speed is V, angle is , plate thickness is h, then cutting tip speed in at
the time of intersection is Vx
h
Vx V
50
Notice: The unit is mm. The max thickness of plate is 100 mm, if more than 100mm also
are considered to be 100mm
Cutting Type: There are two cutting types : Oxygen fuel gas and Plasma parameters. You

can press or to switch with them.

7.2 Flame Parameters

The oxygen fuel parameters, in Fig 7.2, control time delay in IO operation, and whether use
high adjustment.

40
 F2300 Digital Control Incise Machine System Manual

Fig7.2 Flame Parameters

Ignition Time: the time delay of opening ignition I/O.
Low Preheat Time: The preheating time before perforating the steel plate. Enter any
positive number ,unit is s. During the low pressure preheating process, you can prolong
the preheating time by pressing stop key, then the preheating time will delay until you
press the start key to start to high pressure preheat delay.
High Preheat Time: Like Low Preheat Time except open different IO.
Pierce 1 time: Perforation time with low pressure fuel gas. Enter any positive
number ,unit is s.
Pierce 2 time: Perforation time with middle pressure fuel gas. Enter any positive
number ,unit is s.
Pierce 3 time: Perforation time with high pressure fuel gas. Enter any positive
number ,unit is s.
Exhaust Time: The delay of turned off oxygen gas to open the exhaust. Enter any
positive number ,unit is s.
Torch Up Time: When oxygen gas is turned off, the time for the torch to lift up. Enter
any positive number ,unit is s.
Torch Down Time: When oxygen gas is turned off , the time for the torch to put down.
Enter any positive number ,unit is s.
Pierce Up Time: Time for the torch to lift up during perforating. The difference
between Torch Up Time and Pierce Up Time is that: Torch Up Time means the time
that the torch needs to lift up when it needs to move to another place after the current

41
 F2300 Digital Control Incise Machine System Manual

cutting is over; while the Pierce Up Time means the time that the torch needs to lift up
after preheating in the fixed cycle of perforation.
Pierce Down Time: Time for the torch to put down in the perforation. The difference
between Torch Down Time and Pierce Down Time is that: Torch Down Time means
the time that the torch needs to put down before preheating; while the Pierce Down
Time means the time that the torch needs to put down after finishing Torch Up Time
and opening cutting oxygen in the fixed cycle of perforation.
THC Adjustment: According to the user device configuration, choose whether or not
to use high adjustment box.

7.3 Plasma Parameters

As shown in the fig 7.3, these are Plasma Parameters, which are related with the precision of
transmission shaft of the machine.

Fig 7.3 plasma parameters

Arc timeBefore the arc starting, the system time to wait. At this point, all output I /O
are turned off. Enter any positive number ,unit is s.
Pierce time: Perforation time. Enter any positive number ,unit is s.
Torch Up Time: When arc press is turned off, the time for the torch to lift up. Enter
any positive number, unit is s.
Arcing Check Time: Enter any positive number, unit is s. If not detected any feedback
signal of success arc starting within the detection time, the system prompts an error
42
 F2300 Digital Control Incise Machine System Manual

message and terminates the current work of cutting, according memory breakpoints to
withdraw from the program.
Position check Time: Enter any positive number, unit is s. Delay time of the success of
position check.
Position up Time: Enter any positive number, unit is s. Before positioning check, the
time for the torch to lift up.
Close arc: In setting the rate of X%, open the output port, close the arc press signal, to
prevent the steel melting under low-speed cutting tip due to temperature is too high.
Distance to close arc: in the minimum distance of the cutting line of the initial
segment or end segment, close the arc voltage increases.
Lose arc delay: detect the delay time of the feedback of the broken arc, if theres still
no arc voltage input, the situation is considered to be broken arc. This parameter can
effectively avoid the arc broken alert because of the sensitivity of the broken arc
detection in the cutting methods with lead, this guarantees the continuousness of the
cutting and avoid the interrupt of frequent alert .
Watch arc enable: Real-time detection of arc voltage signal in cutting process.

If setting "yes", in the cutting process, the system detects he real-time arc voltage
feedback signal. If do not detect the signal, the system terminates the current work of
cutting, according memory breakpoints to withdraw from the program.
If installing a "No", then in the cutting process does not detect arc voltage feedback
signal.

7.4 Powder Parameters

As shown in the Fig 7.4, these are Powder Parameters, which are related with the precision of
transmission shaft of the machine.

43
 F2300 Digital Control Incise Machine System Manual

Fig 7.4 powder parameters

Dust Ignition Time: Enter any positive number, unit is s.
Dust Preheat Time: Enter any positive number, unit is s.
Raise Dust Open/ Close Time: The time of raise dusting port relatively to the powder
port. Enter any positive number, unit is s.
Dust Up Time: The time for the torch to lift up.
Dust Down Time: The time for the torch to put down.
Dust Horizontal Offset: The horizontal displacement of powder gun relative to the
cutting tip.
Dust Vertical Offset: The Vertical displacement of powder gun relative to the cutting
tip.

7.5 System parameters

The system parameters, as showed in Fig 7.5, are related with the precision of transmission
shaft of the machine.

44
 F2300 Digital Control Incise Machine System Manual

Fig 7.5 System Parameters

Horizontal Axis Pulse: The number of pulse that system needs to generate when the
machine move1mm towards X axis, maintaining 3 digits at most after decimal point.
Vertical Axis Pulse: The number of pulse that system needs to generate when the
machine move 1mm towards Y axis , maintaining 3 digits at most after decimal point.
Max Cutting Speed: the maximum cutting speed, unit is mm./m.
Max G00 speed: the allowable maximum speed when cutting tips idling.
Small Arc Limit: Maximum speed at cutting a small arc.
Small arc definition:
0 mmpm< cutting speed <2000mmpm small arc=5mm

2000 mmpm< cutting speed <4000mmpm small arc =10mm

4000 mmpm< cutting speed <6000mmpm small arc =15mm

6000 mmpm< cutting speed <8000mmpm small arc =20mm

8000 mmpm< cutting speed <10000mmpm small arc =25mm

10000mmpm< cutting speed <12000mmpm small arc =30mm

12000mmpm< cutting speed <15000mmpm small arc =35mm
Flame adjust time: the whole time for the system accelerates from its start speed to the
expected cutting speed.
Plasma adjust time: when plasma cutting , from the time the motor starts to the time

45
 F2300 Digital Control Incise Machine System Manual

when the motor is up to the cutting speed.

Emergency STOP Time: When encounter Emergency Stop input, the time for dropped
from the current speed to zero.
Start Speed: the systems speed when it began to start. Generally do not have to start
from 0 , motor will allow a start speed.
Max Coordinate: The maximum positive coordinate which the machine can reach
horizontally. Its unit is mm(millimeter). If current coordinate exceeds the value, the
system will stop running.
Min Coordinate: The minimum negative coordinate which the machine can reach
horizontally. Its unit is mm(millimeter). If current coordinate is less than the value, the
system will stop running

7.6 Parameter import

In the parameter configuration interface, press F6 to import the parameters. The

parameters should satisfy two conditions:
1. The parameters exported from the incising machine control system( refer to 7.7 Parameter
Export) should satisfy the specified format. The file format is F2300.DAT
2. The file should be stored under the root folder of flash disk which is connected to the USB
interface.
When the above condition is satisfied, in the Fig 7.6, press Enter to confirm, and then you
could import the backup parameters to the system.

Fig 7.6 Parameter import

46
 F2300 Digital Control Incise Machine System Manual

7.7 Parameter export

After the parameter configuration is over, press F7 in the parameter configuration

interface to export the parameters, you should connect the flash disk to the USB interface
before exporting.
In the interface shown in Fig 7.7, after pressing Enter, the parameters will automatically
be saved in the root folder of flash disk, the file name is F2300.DAT

Fig 7.7 Parameter export

7.8 Save parameters

After parameter modification, press F8 to save, shown in Figure 7.8

47
 F2300 Digital Control Incise Machine System Manual

Fig 7.8 System Parameters

Note when any parameter has been modified you must take preservation operation to keep
modification valid, or the system will take the original parameters.

48
 F2300 Digital Control Incise Machine System Manual

Chapter 8 Diagnosis Function

Fig8.1 Diagnostic interface

You can be diagnosing the I/O and keyboard in the interface.

49
 F2300 Digital Control Incise Machine System Manual

8.1 Diagnosis interface index

F5
System Diagnosis

F1
Input Diagnosis

F2 Output
Diagnosis

F5
Keyboard
Diagnosis

F6
System Self-test

F7
Date time

F8
System Definition

F1
F2Parameters F3 F4 F5 F6
Parameters
Backup Definition Encryption Decrption Language
Reset

8.2 Input Diagnosis

The system will read current IO information when press F1 (Refresh) to refresh the
interface, and display all IOs status. On means the input is effective, and Off means the input
is ineffective.

8.3 output Diagnosis

In diagnosis interface ,press F2to enter output diagnosis interfaceshown as Fig8.2

50
 F2300 Digital Control Incise Machine System Manual

Fig 8.2 Output diagnosis

Press,,,, you can move the cursor to the corresponding output port, pressF3
to open the corresponding output port, pressF4 to close the corresponding output. represents
the valid output, represents the invalid output.

8.4 Key-press Diagnosis

In the diagnostic interface, a key value will be displayed behind KEY:, whenever the key is
pressed.

51
 F2300 Digital Control Incise Machine System Manual

Fig 8.3 Keyboard Diagnosis

8.5 System self-check

In the system diagnosis interface, press F6 to enter the system self-check interface.

52
 F2300 Digital Control Incise Machine System Manual

Fig 8.4 System self-check

If the self-check is OK, the system will show:

Fig 8.5 Self-check pass

If the self-test is down, there will be the following alarm type:
DSP Dual ram is error
ARM Dual RAM is error
When coming across these situations, please power off, reboot after about half minutes. If the
situation happened on the machine which has been working for long time, please open the chassis
and clean up the dust.

8.6 date and time

Press F7 in the system diagnosis interface to set the date and time

53
 F2300 Digital Control Incise Machine System Manual

Fig 8.6 System time

Move the cursor to the corresponding date, time or week, press to adjust the
time

8.7 System Definition

In the system diagnosis interface, press F8 to enter the system custom definition interface, in
the interface, you could set the input IO, output IO or system coordinate, also reset or backup the
parameters and one key switch between English or Chinese.

8.7.1 Parameter backup and restore

Parameter Backup: The process of parameter backup is, in the main interface press
F5(System Diagnosis), F8( System Definition), F2(Parameter Backup). The system will need code,
after inputting the code 1396, press Enter, the system will import the default parameters. In the
following process, if the parameters is modified or some of them is broken, reset the parameters.
Warning: after adjusting the equipment, please backup the parameters.
Parameter Reset: The process of reset the parameters is, press F5(System Diagnosis) in the
main interface, F8(System Definition), F1(Parameter Reset).
Warning: After resetting successfully, please restart the system.

54
 F2300 Digital Control Incise Machine System Manual

8.7.2 Input definition

The controller could change the IO definition, including changing the order of IO number, the
type of IO( normally open or closed) according to the users need. In the system custom definition
interface, press F3 to enter the definition interface, press F1 to enter the input definition interface.
As shown in fig 8.7.

Fig 8.7 input definition

In the interface press , move the cursor to the position that
needs changing, press PageUpPageDownto change the number of the Input, press
Enterto change the type of the input.
If the external type of input is normally closed, please set the IO type to , if the type is
normally open, please set the IO type to .

8.7.3 Output definition

The controller could change the IO definition, including changing the order of IO number, the
type of IO( normally open or closed) according to the users need. In the system custom definition
interface, press F3 to enter the definition interface, press F1 to enter the input definition interface.
As shown in fig 8.8.

55
 F2300 Digital Control Incise Machine System Manual

Fig 8.8 output definition

In the interface press , move the cursor to the position that

needs changing, press PageUpPageDownto change the number of the Output, press
Enterto change the type of the Output.
The output type is open drain transistor output type.
type means that if the output signal is effective, the transistor is on. type means that is
the output signal is effective, the transistor is off.

8.7.4 Coordinate definition

The system could provide IO definition for the user. As shown in Fig 8.9

56
 F2300 Digital Control Incise Machine System Manual

Fig 8.9 Coordinate Definition

In the interface, press Enter repeatedly to change among 8 type of coordinates. Press F8 to
save.

57
 F2300 Digital Control Incise Machine System Manual

Chapter 9 Graph

In the main interface, pressF1(ShapeLib) to enter graph interfaceshown as follows:

Fig 9.1 first page of graph

You can press to choose different graph.

9.1 Choose Graph

In home interface of graph, move the cursor to the required graph, press F8 to confirm,
shown as Fig 9.2:

58
 F2300 Digital Control Incise Machine System Manual

Fig 9.2 Chip size interface

You can press to modify sizes, after modification , press F8
to confirmed.
Press any key to return to graphics processing interface as shown in Fig3.3.

9.2 Film/Hole Size

In Fig 9.2 interface, you can press F2to choose hole size, shown as Fig 9.3:

59
 F2300 Digital Control Incise Machine System Manual

Fig 9.3 hole size

Modify sizes like modify chip sizes.
After modification , press F8 to confirmed.
Press any key to return to graphics processing interface as shown in Fig3.3.
Note:
The following graphics dont have hole sizes:
Straight line groove, Bevel groove, Straight line kerf, Vertical kerf, Hole-in- Rotundity,
Rectangle window, Hole-in-Rectangle, Four-holes in Rotundity, Holes in flange, Four-holes in rec,
Four-holes in Filleted corner rec, Five-holes in rec, "Five-holes in Filleted corner rec, Curved
trapezoid, Curved polygon, Testing Shape, Grid Shape.

60
 F2300 Digital Control Incise Machine System Manual

Chapter 10 Port Explanation

10.1 Input port

+3.3V +24V

To
CPU

External
input
signal
3.3VG
24VG
System

Fig10.1 input port circuit

Input signal is a mechanical contact switch, normally open type, it is effective when it is

connected to 24VGand it is ineffective when it is float or connected to 24V

16 input ports totally

Input signal definition

Pin number Signal name remark

1 X+ limit X+ stop inputfloat it if not use, this is horizontal

14 X- limit X- stop inputfloat it if not use, this is horizontal

2 Y+ limit Y+ stop inputfloat it if not use, this is vertical

15 Y- limit Y- stop inputfloat it if not use, this is vertical

3 Emergency stop Emergency stop input, float if not use

4 Arcing

successfully

61
 F2300 Digital Control Incise Machine System Manual

5 Positioning

successfully

6 Plasma collision

7 Move left/C Remote control input

8 Move right/D Remote control input

62
 F2300 Digital Control Incise Machine System Manual

10.1.1 Input Wiring Instructions

Right limit 1
Right limit input
Left limit input
Left limit 14

Front limit 2 Front limit input

Back limit 15
Back limit input

Emergency Stop 3
Emergency
stop input
ignition 16
Arcing
Arcing
4 successfully
successfully
feedback
Cutting oxygen 17

Positioning
Positioning successfull
5
successfully y feedback
Torch up 18

Plasma collision 6
Plasma collision feedback
Torch down 19

Move left 7

NC 20 1.For Plasma cutting

2.Accessed when CNC positioning is
Move right 8
needed. And positioning successfully
NC 21 input should be configured as
normally open type. Or it can be not
Move ahead 9 accessed when using height adjusting
device to positioning.
NC 22 3.When plasma collision detection is
needed, accessed to plasma collision
Move backward 10 feedback.
Caution: All inputs can be
NC 23 normally closed or normally
open, and all inputs are
NC 11
normally open in defualt.
+24V 24

+24V 12

24VG 25 com
connecting to 24VG of the
24VG 13
system or connecting to the 24VG
of the external 24V switching
power supply.

Fig 10.2 External input terminal

63
 F2300 Digital Control Incise Machine System Manual

10.1.2 Remote Input

The system supports two external remote control input, one for line input type, the other for
8421 encoded input type.
Line Input Type
The pin 7, 8,9,10 of input port represents left, right, forward, backward, when inputting
valid signal , the machine can move toward the corresponding direction, when the input signal is
invalid, the machine stop moving.
When the input signal of pin 16 is valid, the system will ignite the torch , the ignition time
is the setting value in system parameters, please take the reference of part of "ignition time " in
"7.2 oxygen gas parameters " .
When the input signal of pin 17 is valid, the system will turn on or off the
cutting oxygen. When the cutting oxygen is on, the system cut off the oxygen, when
the cutting oxygen is off, open the cutting oxygen system.
When the input signal of pin 18 is valid, the system will raise the cutting torch, when the
signal invalid, the torch stops.
When the input signal of pin 19 is valid, the torch goes down, when the signal invalid, the
cutting torch stops.
The external switches of line input are designed by the user..
8421 code input

Input pin 9, 10, 7, 8 is the A, B, C, D bits of the 8421 code. Functions are shown in Table

10.2

Table 10.2 function of 8421 code input

Decimal 8421 code(DCBA) Function

0 0000 No Input

1 0001 Turn on or off the cutting oxygen

2 0010 Go back according to the original track

3 0011 Move forward according to the original track

4 0100 Left lateral movement

5 0101 Ignite Input

6 0110 Start

7 0111 Slow down

8 1000 Accelerate

9 1001 Move for the negative direction vertically

64
 F2300 Digital Control Incise Machine System Manual

10 1010 Move forward vertically

11 1011 Pause

12 1100 cutting torch

13 1101 raise the cutting torch

14 1110 Move toward right horizontally

15 1111 Start

8421-type remote control input is designed by the user, the user can also use the company's
wireless remote control module.

10.1.3 Input Configuration

The number and type of input port can be reconfigured. For example, the right input port can
be Pin 1, also can be configured to Pin 7, input type can be normally open type, can also
be normally close type. Configuration methods are shown in Fig 10.3.
Press F5 (Diagnosis), F8 (SystemDef), F3 (Define), enter the password"1396"and press ENTER.
in turn on the main Interface

Fig10.3 Input Port Configuration

65
 F2300 Digital Control Incise Machine System Manual

In the input configuration interface, move the cursor to numbers of the serial number, Press

the PgUp or PgDn to change the input port number, which also change the pin number of

25-pin input terminal. Move the cursor to place, you can press ENTER to change

the input type. is for the normally open type of the input , when invalid , it is for the signal

of turning off, when effective, it is for the signal of closure. is the normally closed type

of input , when invalid ,it is the signal of closure, when effective ,it is the signal of turning off.

10.2 Output Port

+3.3V +24V

External
Relay

To
CPU

24VG
3.3VG
System

Fig10.4 output port circuit

Output voltage is 24VDClow level is effective

Maximum output current I max 300mA

16 output ports totallu

Output signal definition

25Chip interface Pin No.(Main Signal Remark

connector)

3 Ignite

1 Low pressure preheat

17 High pressure preheat

4 Low pressure cutting

66
 F2300 Digital Control Incise Machine System Manual

oxygen

5 Medium pressure cutting

oxygen

14 High pressure cutting

oxygen

2 Torch up

15 Torch down

6 Exhaust

8 Enable high adjusting

box

19 Plasma locating

16 Plasma arc starting

18 Corner low-speed output

Or automatic / manual

07 Spray dust

20 Raise dust

21 Dusting Preheat

9102223 Not used

11,12,24 +24V +24V/3Aoutput

13,25 24VG +24Vground

10.2.1 Output Wiring Instructions

10.2.1.1 oxygen gas typical connection

67
 F2300 Digital Control Incise Machine System Manual

+24V(common)
Control of perheat
oxygen and fuel Control of
Low pressure gas (low active) gas and
preheat 1
preheat
Control of cutting
High pressure oxygen(low active) oxygen
cutting oxygen 14
Torch up control(low active) valve
Torch up 2

Torch down 15
Torch down control(low active)

Ignite Ignition enable(low active)

3
Plasma arc
starting 16
Low pressure
4
cutting oxygen
High pressure 17
preheat
Mid-pressure
5
preheat
Low rate at 18
corner
Exhaust control(low active)
exhaust 6

Plasma
19
positioning
Spray powder 7

Raise powder 20 Capacitor height adjusting

Enable height 8
enable(low active)
adjusting
Powder preheating 21

unused 9

unused 22

unused 10

unused 23
Caution: All outputs can be
high active or low active,
+24V 11 system default is low active .
+24V 24

+24V 12
COM
24VG 25 connecting to system supply
24VG. Or connecting to the +24V
24VG 13 side of external 24V switching
power supply.

Fig10.5 oxygen gas typical connection

68
 F2300 Digital Control Incise Machine System Manual

10.2.1.2 Three level perforation circuit

+24V(common)
Control of perheat
oxygen and fuel Control of
Low pressure gas(low active) gas and
preheat 1
preheat
Level three
High pressure perforation(low active) oxygen
cutting oxygen 14
Torch up control(low active) valve
Torch up 2

Torch down 15
Torch down control(low active)

Ignite Ignition control(low active)

3
Plasma arc
starting 16
Low pressure Level one perforation(low active)
4
cutting oxygen
High pressure High pressure preheat(low active)
17
preheat
Mid-pressure Level two perforation(low active)
5
preheat
Low rate at 18
corner
Exhaust control(low active)
exhaust 6

Plasma
19
positioning
Spray powder 7

Raise powder 20 Capacitor height adjusting

Enable height 8
enable(low active)
adjusting
Powder preheating 21

unused 9

unused 22

unused 10

unused 23
Caution: All outputs can be
high active or low active,
+24V 11 system default is low active.
+24V 24

+24V 12
COM
24VG 25 connecting to system supply
24VG.Or connecting to the +24V
24VG 13 side of external 24V switching
power supply.

Fig 10.6 three level perforation circuit

69
 F2300 Digital Control Incise Machine System Manual

10.2.1.3 Typical circuit of using powder

+24V
Low pressure
preheat 1
High pressure
cutting oxygen 14

Torch up 2

Torch down 15

Ignite Ignition control(effective low)

3
Plasma arc
starting 16
Low pressure
4
cutting oxygen
High pressure 17
perheat
Mid-pressure
5
preheat
Low rate at 18
corner
exhaust 6

Plasma
19
positioning
Spray powder control(low active)
Spray powder 7

Raise powder 20
Raise or stir powder control(low active)

Enable height 8
adjusting
Powder preheat (low active)
Powder preheating 21

unused 9

unused 22

unused 10

unused 23
Caution: All outputs can be
effective high or effective low,
+24V 11 system default is effective low .
+24V 24

+24V 12
COM
24VG 25 connecting to system supply
24VG,Or connecting to the +24V
24VG 13 side of external 24V switching
power supply.

Fig 10.7 powder typical circuit

70
 F2300 Digital Control Incise Machine System Manual

10.2. 1.4 typical circuit of using plasma cutting

+24V(common)

Low pressure
preheat 1

High pressure 14
cutting oxygen Torch up control(Low
Torch up 2 active)
Torch down control(Low
Torch down 15 active)
Ignite 3 Connect to high
Plasma adjusting devices Low
16
Low pressure arc starting input or active
cutting oxygen 4 arc starting delay
High pressure 17
preheat
Medium Connect to high
pressure cutting 5 adjusting devices
oxygen corner low speed or
Corner low speeed 18 (Low active)
automatic / manual
Exhaust 6
Connect to the locating
Plasma locating input of lifting device
19 Low active
when CNC locating is
Spray dust 7 needed
Raise dust 20

Enable high 8
adjusting box
21
Dusting preheat
Not used 9

Not used 22

Not used 10 Note:All outputs

Not used are low active or
23
high active, the
+24V 11
system takes low
+24V 24 active as default.
+24V 12
COM
24VG 25 Connecting to the systems
+24V supplyalso external
24VG 13 24VSwitch supply +24V port
allowed

Fig 10.8 Typical wiring diagram of the plasma

Instruction
Height-adjusting device wiring with corner low-speed
When the height-adjusting device takes corner low-speed input control signal, the
system's "corner low speed" output signal is used to control the height-adjusting device's corner
low-speed input. The system takes an open-colletor transistor output, with the default active low
signal. When the height-adjusting device is not of appropriate type, it needs to be converted by the
delay.

71
 F2300 Digital Control Incise Machine System Manual

Height-adjusting device wiring with automatic / manual

When the height-adjusting device takes automatic / manual control function instead of corner
low-speed input, the system needs to use the "corner low-speed" output to control the
height-adjusting device's automatic / manual signal. When the height-adjusting device is not of
appropriate type, it needs to be converted by the delay. Meanwhile, it needs to change the type of
corner low speed from normally-open to normally-closed in the output configuration interface
(Section 10.2.2), i.e from "" to "".
Using height-adjusting device locating
When using the locating function of the height-adjusting device, the locating of numerical
control should be closed. The approach is to change the input type of successful locating from
normally-open to normally-closed in the input configuration interface(Section 10.1.3), i.e from "
" to "". There are two types of locating:
The first: locating controlled by the plasma arc starting. CNC emits the plasma arc
starting, the height-adjusting device starts arc after locating, and sends arc starting success back to
CNC after starting arc successfully. Such devices available in the market include AngTai,
HongYuDa, HaiSi and other brands. Such devices can connect the "plasma arc starting" output of
CNC system to the " starting arc with locating" input of the height-adjusting devices, and at the
same time in the plasma parameters (refer to section 7.4 of plasma parameters) set the arc
detecting time to the value that allows for completing the testing and starting arc.
The second: finish position from the decline of the cutting torch . Before issuing the
command of starting arc, first issue the command of declinging the height adjust device, then issue
the command of starting arc.These kind of height adjust devices could be SiDaTe, HongYuDa in
markets. When using these kind of heigh adjust device, transfer to the interface of plasma
parameters(refer to section 7.4 of plasma parameters),set the plasma detecting time to the same as
the time of location of cutting touch.
Using CNC system locating
When using the location function of digital controll system, first entering the input
configuration interface, set the input type of successful location from normally closed to normally
open type, ie, from "" to "". At the same time, return the signal of successful location to the
input of the successful location of the digital controller.

10.2.2 Output configuration

The number and type of the output could be configured, for example, the igniting output
number could be 3,also it could be configured to 07, the output type could be normally open or
normally closed. The detailed methods are shown in figure 10.9.
Press F5(Diagnosis) in the main interface, F8(Systemdef), F3 (Define), enter the password
"1396" and press ENTER, F2(output).

72
 F2300 Digital Control Incise Machine System Manual

Fig 10.9 Output Configuration

In the output configuration interface, move the cursor to numbers of the serial number, Press
the PgUp or PgDn to change the input port number, that also changes the pin number of 25-pin
input terminal. Move the cursor to place, you can press ENTER to change the input type. "
" is for the normally open type of the input , when invalid , it is for the signal of turning off,
when effective, it is for the signal of closure. "" is the normally closed type of input , when
invalid ,it is the signal of closure, when effective ,it is the signal of turning off.

10.3 Motor Port

XDIR+
XDIR-
XDIR/XPWM- Y+ XCP+
X XCP-
XPWM+ Signal Y-
YDIR+
YDIR/YPWM- Shaping Photoele- Different- YDIR-
ctric ial output YCP+
YPWM+
isolation YCP-

System

73
 F2300 Digital Control Incise Machine System Manual

Fig10.10 motor port schematic diagram

Signal definition table
Number of the signal Remarks

15 pin interface

1 XDIR+ Positive at the horizontal axis

9 XDIR- Negative at the horizontal axis

2 XCP+ Positive pulse at the horizontal axis

10 XCP- Negative pulse at the horizontal axis

3 YDIR+ Positive at the vertical axis

11 YDIR- Negative at the vertical axis

4 YCP+ Positive pulse at the vertical axis

12 YCP- Negative pulse at the vertical axis

5 ZCP Positive pulse at the perpendicular axis

13 ZCP Negative pulse at the perpendicular axis

6 ZDIR Positive at the perpendicular axis

14 ZDIR Negative at the perpendicular axis

7 +5V +5V/500mA Power output

15,8 5VG 5V Power Ground

10.3.1 Typical wiring diagram of the electrical motor interfaces

10.3.1.1 connection methods for differential stepper driver

74
 F2300 Digital Control Incise Machine System Manual

Power input
XDIR+ 1 DIR+
XDIR- 9 DIR-

XCP+ 2 PUL+

XCP- 10 PUL-
YDIR+ 3

YDIR- 11 ENA+
ENA-
YCP+ 4

12
YCP- Stepper Drives
5

13

6 Power
input
14 DIR+
+5V 7 DIR-
5VG 15
PUL+
5VG 8
PUL-
Offline
switch
ENA+
ENA-

Stepper Drives

Fig 10.11 connection methods for differential stepper driver

75
 F2300 Digital Control Incise Machine System Manual

10.3.1.2 Com -anode connection methods for stepper driver

Power
+V input
XDIR+ 1

XDIR- 9 DIR

XCP+ 2 PUL

XCP- 10 Free
YDIR+ 3

YDIR- 11

YCP+ 4

12
YCP- Stepper drives
5

13

6
Power
input
14 +V
+5V 7 DIR
5VG 15
PUL
5VG 8
Offline
switch
Free

Stepper drives

Figure 10.12 com-anode connection methods for stepper driver

76
 F2300 Digital Control Incise Machine System Manual

10.3.1.3 Connection methods of Servo driver of Panasonic Company

Power
input
XDIR+ 1 5 SING1
XDIR- 9 6 SIGN2

XCP+ 2 3 PULS1

XCP- 10 4 PULS2
YDIR+ 3

YDIR- 11

YCP+ 4

YCP-
12 Panasonic
A5/A4
5

13

6
Power
input
14
5 SING1
+5V 7 6 SIGN2
5VG 15
3 PULS1
5VG 8
4 PULS2

Panasonic
A5/A4

Figure 10.13 Connection methods of Servo driver of Panasonic Company

77
 F2300 Digital Control Incise Machine System Manual

10.3.2 Coordinate Mapping

In order to change the map coordinates of the system, you need to go to

the define interface. The process is to Press F5(Diagnosis) in the main interface, F8(Systemdef),
F3 (Define), enter the password "1396" and press ENTER, then press F3 (Axes). As shown in
Figure 10.14.

Fig 10.14 Coordinate Mapping

Continuously pressEnterkey, the direction of the arrow outside coordinates definition
will change , the maximum coordinate mapping is eight. After adjusting the direction of the
coordinates mapping, press F8 to Save.

78
 F2300 Digital Control Incise Machine System Manual

Chapter11 Installation and Debugging

11.1 Horizontal / vertical pulses number setting

Horizontal / vertical pulses number setting

Its easy to set the horizontal(vertical) pulses number. Before drawing a line , assume one
value of horizontal pulses XPls and one value of vertical pulses YPls, set these two parameters and
then save the settings. Enter the manual interface, choose fixed moving function. Assume the fixed
distance is Amm. Move A mm horizontally, and the actual length of the line is B mm (which is
generally not equal to A), then we can calculate the horizontal pulses number. The equation is

A
XPls
B . After calculating , replace the outcome with the assumptive Xpls(take three decimal
places at most). Similarly, move C mm vertically, the actual length is D mm, then the vertical

C
YPls
pulses number is D.
requirement of pulses number
The maximum frequency of output pulses from the system is 200 KHz. It is not possible to
work properly according to the order if the pulse frequency is higher than 200KHz. Assume the
pulse number is x, the highest speed is Mv (mm/min), then (Mv*x/60) should be less than 200000.
For example, the pulse number is x=2000, the highest speed is
Mv=12000(mm/min).Because of Mv*x/60=12000*2000/60=400000>200000, the speed of
12000(mm/min) is not reachable. If we set x to be 1000, then Mv*x/60 = 12000*1000/60 =
200000, this time it can just to reach the operating speed of 12,000. While in principle the number
of pulses can be set to a large value, in fact it should follow these two settings. Because the
frequency is too high, some drives cant work very well, the motor will be out of synchronism. On
the other hand, the performance of anti-jamming is of foreign interference is poor, and the external
interference is strong.

79
 F2300 Digital Control Incise Machine System Manual

Chapter12 The use of BIOS

When the system powers on, it will display as shown in Fig 12.1.

Fig 12.1 power on

When press DEL before the system counts down to 0, the system will enter the BIOS. If other
keys are pressed, the system will enter in before counting down to 0.

F1 - (System software update)

F2 - (Welcome picture update)
F3 - (Motion update)
F4 - (System backup)
F5 - (System recovery)
F6 - (Start system)

Fig 12.2 BIOS interface

80
 F2300 Digital Control Incise Machine System Manual

12.1 System upgrade

After entering BIOS, press F1 to upgrade the system, it should satisfy the following
conditions:
Flash Disk is connected to the system.
There should be the UserApp.exe upgrade file in the root folder of the flash disk.
Pressed F1 to upgrade when the conditions are satisfied, when completing the upgrading, press F6
to reboot.

12.2 Welcome interface upgrading

After entering BIOS, press F2 to upgrade the welcome interface completely, it should satisfy
the following conditions:
Flash Disk is connected to the system.
There should be the STARTBMP.BIN upgrade file in the root folder of the flash disk.
Pressed F6 to upgrade when the conditions are satisfied, when completing the upgrading, press F6
to reboot.

12.3 Movement control upgrade

After entering BIOS, press F2 to upgrade the welcome interface completely, it should satisfy the
following conditions:
Flash Disk is connected to the system.
There should be the MOTION.DSP upgrade file in the root folder of the flash disk.
Pressed F3 to upgrade when the conditions are satisfied, when completing the upgrading, press F6
to reboot.

12.4 Movement Backup

after entering BIOS, press F4 to backup.

12.5 System Reset

After entering BIOS, press F5 to return to the original system that has been backup.

81
 F2300 Digital Control Incise Machine System Manual

Appendix 1 GM code rapid consult

Serial number order function

1 G99 rotationproportionmirror image
2 G92 reference coordinate
3 G91 Relative coordinate system
4 G90 Absolute coordinate system
5 G20 English unit
6 G21 Metric unit
7 G41 Left kerf gap compensation
8 G42 Right kerf gap compensation
9 G40 Cancel kerf gap compensation
10 G00 Quickly move
11 G01 Liner cutting
12 G02 Clockwise arc cutting
13 G03 Anticlockwise arc cutting
14 G04 Program delay
15 M07 Start cutting cycle
16 M08 Stop cutting cycle
17 M02 Program end
14 G04 Program delay
15 M07 Start cutting cycle
16 M08 Stop cutting cycle
17 M02 Program end

82