M54HC151

M74HC151

8 CHANNEL MULTIPLEXER

. HIGH SPEED

. tPD = 15 ns (TYP.) AT VCC = 5 V

LOW POWER DISSIPATION

. ICC = 4 A (MAX.) AT TA = 25 C
HIGH NOISE IMMUNITY

. VNIH = VNIL = 28 % VCC (MIN.)

OUTPUT DRIVE CAPABILITY B1R F1R

. 10 LSTTL LOADS
SYMMETRICAL OUTPUT IMPEDANCE
(Plastic Package) (Ceramic Package)

. IOH = IOL = 4 mA (MIN.)

BALANCED PROPAGATION DELAYS

. tPLH = tPHL
WIDE OPERATING VOLTAGE RANGE M1R C1R

. VCC (OPR) = 2 V TO 6 V
PIN AND FUNCTION COMPATIBLE
WITH 54/74LS151
(Micro Package)
ORDER CODES :
M54HC151F1R
(Chip Carrier)

M74HC151M1R
M74HC151B1R M74HC151C1R
DESCRIPTION
The M54/74HC151 is a high speed CMOS 8 CHAN-
NEL MULTIPLEXER fabricated in silicon gate PIN CONNECTIONS (top view)
C2MOS technology. It has the same high speed per-
formance of LSTTL combined with true CMOS low
power consumption. It provides, in one package, the
ability to select one bit of data from up to eight
sources. The HC151 can be used as a universal
function generator to generate any logic function of
four variables. Outputs Y and W are complementary
selection depends on the address inputs A, B and
C. The strobe input must be taken low to enable this
device, when the strobe is high W output is forced
high and consequently Y output goes low. All inputs
are equipped with protection circuits against static
discharge and transient excess voltage.

INPUT AND OUTPUT EQUIVALENT CIRCUIT

NC =
No Internal
Connection

February 1993 1/11

M54/M74HC151

TRUTH TABLE
INPUTS OUTPUTS
SELECT STROBE
Y W
C B A S
X X X H L H
L L L L D0 D0
L L H L D1 D1
L H L L D2 D2
L H H L D3 D3
H L L L D4 D4
H L H L D5 D5
H H L L D6 D6
H H H L D7 D7

PIN DESCRIPTION IEC LOGIC SYMBOL

PIN No SYMBOL NAME AND FUNCTION
4, 3, 2, 1, D0 to D7 Multiplexer Inputs
15, 14, 13,
12
5 y Multiplexer Output
6 w Complementary
Multiplexer Output
7 STROBE Strobe Input
11, 10, 9 A, B, C Select Inputs
8 GND Ground (0V)
16 VCC Positive Supply Voltage

2/11
 M54/M74HC151

LOGIC DIAGRAM

ABSOLUTE MAXIMUM RATINGS

Symbol Parameter Value Unit
VCC Supply Voltage -0.5 to +7 V
VI DC Input Voltage -0.5 to VCC + 0.5 V
VO DC Output Voltage -0.5 to VCC + 0.5 V
IIK DC Input Diode Current 20 mA
IOK DC Output Diode Current 20 mA
IO DC Output Source Sink Current Per Output Pin 25 mA
ICC or IGND DC VCC or Ground Current 50 mA
PD Power Dissipation 500 (*) mW
o
Tstg Storage Temperature -65 to +150 C
o
TL Lead Temperature (10 sec) 300 C
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these condition isnotimplied.
(*) 500 mW: 65 oC derate to 300 mW by 10mW/oC: 65 oC to 85 oC

3/11
M54/M74HC151

RECOMMENDED OPERATING CONDITIONS

Symbol Parameter Value Unit
VCC Supply Voltage 2 to 6 V
VI Input Voltage 0 to VCC V
VO Output Voltage 0 to VCC V
o
Top Operating Temperature: M54HC Series -55 to +125 C
o
M74HC Series -40 to +85 C
tr, tf Input Rise and Fall Time VCC = 2 V 0 to 1000 ns
VCC = 4.5 V 0 to 500
VCC = 6 V 0 to 400

DC SPECIFICATIONS

Test Conditions Value

Symbol Parameter TA = 25 oC -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
VIH High Level Input 2.0 1.5 1.5 1.5
Voltage 4.5 3.15 3.15 3.15 V
6.0 4.2 4.2 4.2
V IL Low Level Input 2.0 0.5 0.5 0.5
Voltage 4.5 1.35 1.35 1.35 V
6.0 1.8 1.8 1.8
V OH High Level 2.0 1.9 2.0 1.9 1.9
VI =
Output Voltage 4.5 IO=-20 A 4.4 4.5 4.4 4.4
VIH
V
6.0 or 5.9 6.0 5.9 5.9
4.5 V IL IO=-4.0 mA 4.18 4.31 4.13 4.10
6.0 IO=-5.2 mA 5.68 5.8 5.63 5.60
VOL Low Level Output 2.0 0.0 0.1 0.1 0.1
VI =
Voltage 4.5 IO= 20 A 0.0 0.1 0.1 0.1
VIH
V
6.0 or 0.0 0.1 0.1 0.1
4.5 V IL IO= 4.0 mA 0.17 0.26 0.33 0.40
6.0 IO= 5.2 mA 0.18 0.26 0.33 0.40
II Input Leakage VI = VCC or GND 0.1 1 1 A
6.0
Current
ICC Quiescent Supply 6.0 VI = VCC or GND 4 40 80 A
Current

4/11
 M54/M74HC151

AC ELECTRICAL CHARACTERISTICS (C L = 50 pF, Input t r = tf = 6 ns)

Test Conditions Value
o
Symbol Parameter TA = 25 C -40 to 85 oC -55 to 125 oC Unit
VCC
54HC and 74HC 74HC 54HC
(V)
Min. Typ. Max. Min. Max. Min. Max.
tTLH Output Transition 2.0 30 75 95 110
tTHL Time 4.5 8 15 19 22 ns
6.0 7 13 16 19
tPLH Propagation 2.0 56 130 165 190
tPHL Delay Time 4.5 16 26 33 38 ns
(D - W)
6.0 14 22 28 32
tPLH Propagation 2.0 56 130 165 190
tPHL Delay Time 4.5 16 26 33 38 ns
(D - Y)
6.0 14 22 28 32
tPLH Propagation 2.0 30 85 105 125
tPHL Delay Time 4.5 10 17 21 25 ns
(STROBE - W)
6.0 9 14 18 21
tPLH Propagation 2.0 30 85 105 125
tPHL Delay Time 4.5 10 17 21 25 ns
(STROBE - Y)
6.0 9 14 18 21
tPLH Propagation 2.0 72 160 200 235
tPHL Delay Time 4.5 20 32 40 47 ns
(A, B, C - W)
6.0 17 27 34 40
tPLH Propagation 2.0 72 160 200 235
tPHL Delay Time 4.5 20 32 40 47 ns
(A, B, C - Y)
6.0 17 27 34 40
CIN Input Capacitance 5 10 10 10 pF
CPD (*) Power Dissipation 63
pF
Capacitance
(*) CPD is defined as the value of the ICs internal equivalent capacitance which is calculated from the operating current consumption without load.
(Refer to Test Circuit). Average operting current can be obtained by the following equation. ICC(opr) = CPD VCC fIN + ICC

TEST CIRCUIT ICC (Opr.)

* INPUT WAVEFORM IS THE SAME AS THAT IN CASE OF SWITCHING CHARACTERISTICS TEST.

5/11
M54/M74HC151

SWITCHING CHARACTERISTICS TEST WAVEFORM

6/11
 M54/M74HC151

Plastic DIP16 (0.25) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

a1 0.51 0.020

B 0.77 1.65 0.030 0.065

b 0.5 0.020

b1 0.25 0.010

D 20 0.787

E 8.5 0.335

e 2.54 0.100

e3 17.78 0.700

F 7.1 0.280

I 5.1 0.201

L 3.3 0.130

Z 1.27 0.050

P001C

7/11
M54/M74HC151

Ceramic DIP16/1 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 20 0.787

B 7 0.276

D 3.3 0.130

E 0.38 0.015

e3 17.78 0.700

F 2.29 2.79 0.090 0.110

G 0.4 0.55 0.016 0.022

H 1.17 1.52 0.046 0.060

L 0.22 0.31 0.009 0.012

M 0.51 1.27 0.020 0.050

N 10.3 0.406

P 7.8 8.05 0.307 0.317

Q 5.08 0.200

P053D

8/11
 M54/M74HC151

SO16 (Narrow) MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.
A 1.75 0.068
a1 0.1 0.2 0.004 0.007
a2 1.65 0.064
b 0.35 0.46 0.013 0.018
b1 0.19 0.25 0.007 0.010
C 0.5 0.019
c1 45 (typ.)
D 9.8 10 0.385 0.393
E 5.8 6.2 0.228 0.244
e 1.27 0.050
e3 8.89 0.350
F 3.8 4.0 0.149 0.157
G 4.6 5.3 0.181 0.208
L 0.5 1.27 0.019 0.050
M 0.62 0.024
S 8 (max.)

P013H

9/11
M54/M74HC151

PLCC20 MECHANICAL DATA

mm inch
DIM.
MIN. TYP. MAX. MIN. TYP. MAX.

A 9.78 10.03 0.385 0.395

B 8.89 9.04 0.350 0.356

D 4.2 4.57 0.165 0.180

d1 2.54 0.100

d2 0.56 0.022

E 7.37 8.38 0.290 0.330

e 1.27 0.050

e3 5.08 0.200

F 0.38 0.015

G 0.101 0.004

M 1.27 0.050

M1 1.14 0.045

P027A

10/11
 M54/M74HC151

Information furnished is believed to be accurate and reliable. However, SGS-THOMSON Microelectronics assumes no responsability for the
consequences of use of such information nor for any infringement of patents or other rights of third parties which may results from its use. No
license is granted by implication or otherwise under any patent or patent rights of SGS-THOMSON Microelectronics. Specifications mentioned
in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied.
SGS-THOMSON Microelectronics products are not authorized for use ascritical components in life support devices or systems without express
written approval of SGS-THOMSON Microelectonics.

1994 SGS-THOMSON Microelectronics - All Rights Reserved

SGS-THOMSON Microelectronics GROUP OF COMPANIES

Australia - Brazil - France - Germany - Hong Kong - Italy - Japan - Korea - Malaysia - Malta - Morocco - The Netherlands -
Singapore - Spain - Sweden - Switzerland - Taiwan - Thailand - United Kingdom - U.S.A

11/11