Installation Manual - S200 Landing Door System

ThyssenKrupp Elevator (China)
Technical Information for Elevator Products
(Version ab )
Installation Manual S200 Landing Door System

(R000000251)
Edited by Alex Jin 2012-10-22

Checked by Franck Han 2012-10-22
Standardized by WangJianHong 2012-10-22
Approved by GengXueYi 2012-10-23
ThyssenKrupp Elevators (Manufacturing China) Engineering Center

Installation Manual S200 Landing
Door System
Installation Manual
Version: ab No.: R000000251

Installation Manual No.: R000000251
Warning
The elevator installation personnel should be those who have been trained by Labor and Social
Security Bureau and got the operation certificates. Before installation, please read this installation
manual carefully. All the installation personnel of elevator components should comply with relevant
specifications. Maximum guarantee of elevator performance and passengers safety will be provided
by installation personnel strictly abiding by this manual. ThyssenKrupp Elevator will not be liable for
any loss caused by your operation without compliance with the requirements of this manual and by
your modification or refit of the elevator.
All rights of this manual belong to ThyssenKrupp Elevator. No one can in any forms or by any means
use, copy or distribute any part of the manual for any other purposes without prior written permission
from ThyssenKrupp Elevator. ThyssenKrupp Elevator has the right to change the contents of the
written material without asking for suggestions or prior notification. If have any questions about the
manual, please contact ThyssenKrupp Elevator promptly.

Table of Contents
Chapter I General drawing for S200 landing door system ................................................................. 2

Chapter II Installation of S200 landing door system .......................................................................... 6
2.1 General................................................................................................................................................6
2.2 Safety specifications..........................................................................................................................6
2.3 Preparation of installation tools........................................................................................................7
2.4 Main parameters of S200 landing door system.............................................................................8
2.5 Preparation before S200 landing door installation......................................................................10
2.6 Installation of S200 landing door sill..............................................................................................13
2.7 Installation of landing door hanging components........................................................................22
2.8 Installation of landing door board and slider................................................................................27
Chapter III Maintenance Precautions ............................................................................................... 33
3.1 Wipe the guide rail of the landing door during each time of maintenance, check wear extent
of the door pulley and replacement should be made immediately if it exceeds 1.5mm........33
3.2 Check tension degree of the steel wire rope during each time of maintenance
as shown in figure 3-1.....................................................................................................................33
3.3 Degree of tightness of standard parts should be checked during each
time of maintenance........................................................................................................................33
3.4 Smoothness of the landing door lock actions should be checked during each time of
maintenance.....................................................................................................................................33
3.5 Correct application method of the triangle key............................................................................33
Chapter IV Consumables of S200 Landing Door ............................................................................. 35
Chapter V Appendix ......................................................................................................................... 37
Installation checklist of landing door...........................................................................................................37
5.1 Overall installation confirmation of parts of landing door...........................................................37
5.2 Installation confirmation of landing door on each floor...............................................................38
Chapter I General Drawing for S200 Landing Door System
Figure 1-1 S200 landing door system (center-opening double-leaf)
ThyssenKrupp Elevator (China) 2

Figure 1-2 S200 landing door system (side-opening double-leaf)

Upper installation Landing door hanging

support components
Hanger door bolt kit
Door jamb and lintel

Link
Landing door board
Upright side
installation support
Door slider components
Door jamb upright
Lower installation support

Landing door apron
Landing door sill
Figure 1-3 Structure diagram of S200 landing door system (center-opening double-leaf)

Landing door hanging

components
Upper installation support
Hanger door bolt kit
Door jamb upright

components
Door closing side upright

installation support Upright installation
support
Landing door board
Door slider
components
Landing door sill
Landing door apron
Lower installation
support
Figure 1-4 Structure diagram of S200 landing door system (side-opening double-leaf)

Chapter II Installation of S200 Landing Door System

2.1 General
This manual applies to the installation of S200 landing door system.
The installation method described in the manual is the general installation method of our company
at present and relatively detailed explanation of relevant specific requirements of installation has
been provided in the manual. When the situation of elevator hoist-way is different from the elevator
installation hoist-way arrangement drawing, please consult with our relevant technicians
immediately and apply special installation method.
Installation has a very close relation with clients. In order to carry out the work and improve
efficiency successfully, installation personnel should keep good communication with clients. And
they should try their best to get the strong support of clients to the installation.
2.2 Safety specifications

2.2.1 Explanation of safety identifications
The signs below are used as safety identifications in the manual
Danger sign
When you see this sign, you must be careful because grave danger of personal injury may occur.
Please obey the explanations of this sign.
Electric shock risk sign
When you see this sign, you must be careful because grave danger of personal injury caused by
electric shock may occur.
Warning sign
When you see this sign, you must be careful. Personal injury or property loss may occur if you
dont comply with the explanations of the sign. Please obey the warning sign.
Caution sign

You should pay attention to this sign because important operation directions are included in the
explanations of this sign. Damage to the elevator and its failure may be caused if don't obey the
explanations.
Check sign
Attention should be paid to this sign because the explanations of this sign include the information
of check order. You must carry out strictly in any situations, or personal injury or property loss may
be caused.
2.2.2 Safety measures applied in emergency situations
Emergency unlock
Only professional personnel who know elevator safety specifications very well and
have been trained can open the landing door and car door manually.
2.3 Preparation of installation tools

Tools of S200 landing door system are mainly as following.
Name: wrench Name: circlip pliers Name: leveling rod

Specification: 13~24mm Specification: 175m Specification: 500mm
Name: plumb Name: socket wrench Name: hex wrench

Specification: steel 1kg Specification: 13/16/18/24 Specification: 10/13/16
Name: feeler gauge Name: cross screw driver

(attraction-type)
Specification: 100A21 Specification: 75~200mm

2.4 Main parameters of S200 landing door system
Figure 2-1 Main parameters of S200 landing door system (center-opening double-leaf)

Figure 2-2 Main parameters of S200 landing door system (side-opening double-leaf)

Table 2-2 Main parameters of S200 landing door system (center-opening double-leaf)
Clear door opening width

(mm) 700 800 900 1000 1100 1200 1300
C(mm) 1500 1700 1900 2100 2300 2500 2700
A(mm) 300 350 267 300 300 275 300
S (number of sill support
channel) 3 3 4 4 4 5 5
T (total number of upper
and lower support) 5 5 6 6 8 9 9
Table 2-3 Main parameters of S200 landing door system (side-opening double-leaf)
Clear door opening width

(mm) 700 800 900 1000 1100 1200 1300
C(mm) 1150 1300 1450 1600 1750 1900 2050
A(mm) 330 380 287 320 353.333 290 315
E(mm) 370 420 470 520 579 620 670
S (number of sill support
channels) 3 3 4 4 4 5 5
T (total number of upper
and lower supports) 5 5 6 6 8 9 9
2.5 Preparation before S200 landing door installation

2.5.1 Determine the elevation line of sill surface
Designate the elevation of each floor according to the installation manual of preparation before
installation as figure 2-3 shows
Distance between elevation
((provided by owner)
line and decoration
completion line
Elevation line The distance is different

(provided by owner) with the change of each
floor levelness and
decoration thickness
Decoration
completion line
(provided by owner)
Figure 2-3 Schematic drawing of floor elevation line
Based on the elevation line, draw the sill support channel expansion bolt installation line and landing
door header support expansion bolt installation line on the front side wall of hoist-way of hole preserved
entrance as shown in figure 2-4.

Landing door
header support
expansion bolt
installation line
Clear door opening height + 255

Clear door opening height
Elevation line
(provided by owner)
Decoration
completion line
(provided by owner)
Sill surface
Sill support channel

expansion bolt
installation line
Figure 2-4 Schematic drawing of expansion bolt installation lines of floor sill support channel and
landing door header support
2.5.2 Expansion bolt installation for landing door installation

Attention: Expansion bolt installation lines of landing door header support and
landing door sill support channel must be installed on the concrete wall
structure or weld the landing door header support and landing door sill support
channel with built-in ring beam directly.
Drill the hole of expansion bolt according to the expansion bolt installation lines of sill support channel
and landing door upper installation support and the fixed position of expansion bolt for specific landing
door installation as shown in figure 2-5. The specification of fixed expansion bolts on landing door lower
and upper installation support is M12100 and bolt hole is 16mm. The specification of fixed expansion
bolt on upright installation support is M665 and bolt hole is 10mm.

M12100 expansion bolt Clear door opening width + 250

Landing door upper
Clear door opening width installation support
M665 expansion bolt
Clear door opening

height + 255
Upright installation
support
Sill surface
Decoration
completion surface
M12100 expansion Landing door lower

bolt installation support
Figure 2-5 Drawing of fixed expansion bolt positions of

center-opening double-leaf landing door system
Table 2-4 Dimensions of fixed expansion bolts of

center-opening double-leaf S200 landing door system
Clear door
opening
700 800 900 1000 1100 1200 1300
width
(mm)
E(mm) (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2
A(mm) 300 350 267 300 300 275 300
Number of
2 2 3 3 3 4 4
A

Landing door upper

M12100 expansion bolt
Clear door opening height + 255

M665 expansion bolt
Upright installation
support
Decoration completion
surface of sill surface
Door closing side upright

M12100 expansion bolt Landing door lower

Figure 2-6 Drawing of fixed expansion bolt positions of

side-opening double-leaf landing door system
Table 2-5 Dimensions of fixed expansion bolts

of side-opening double-leaf S200 landing door system
Clear door
opening
700 800 900 1000 1100 1200 1300
width
(mm)
B(mm) (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2 (CH-300)/2
A(mm) 330 380 287 320 353 290 315
Number of
2 2 3 3 3 4 4
A
2.6 Installation of S200 landing door sill

2.6.1 Fix the landing door lower installation support
Fix the lower installation support according to 2.5.2 lower installation support expansion bolt position.
The center-opening double-leaf landing door is made as the example and the installation of side-
opening double-leaf landing door can be carried out with referring to the installation of center-opening
double-leaf landing door as shown in figure 2-7.

Decoration
completion surface
of sill surface
Landing door lower

Door opening centerline
Figure 2-7 Drawing of floor sill support channel installation
2.6.2 Connect landing door sill with sill carrier as figure 2-8 and 2-9 show.
Hex bolt M816 (center-opening
Sill double-leaf)
Hex bolt M1020 (side-opening

double-leaf)
Sill support
channel
Hex flange nut M8 (center-

opening double-leaf)
Hex flange nut M10 (side-opening

double-leaf)
Figure 2-8 Drawing of connecting sill with sill carrier
6 bolts in total
Figure 2-9 Drawing of connecting sill with sill carrier

2.6.3 Install sill carrier on landing door lower installation support as shown in figure 2-10
Sill and sill carrier
Landing door lower

Sill carrier groove slider

(including hex bolt
M12X30)
Hex nut M12, spring washer

12, flat washer 12
Figure 2-10 Sill carrier is installed on landing door lower installation support
2.6.4 Correct sill

a) Adjust the levelness of one end of sill according to elevation offered by owner at first,
namely put one end of 1/600 leveling rod on the sill surface and the other end on the
decoration completion surface (provided by owner) and then measure the levelness in the
longitudinal direction. Levelness is required 1/600. Lock the bolt of landing door lower
installation support on the segment firmly as figure 2-10 shows.
b) Then put the leveling rod in the middle of sill in horizontal direction, adjust the height of
other end of support and make the whole sill level. The levelness of entire sill is required
1/600. Lock other bolts of landing door lower installation support firmly as shown in figure
2-11.
Bolts of landing door
lower installation Sill door opening
width line
support
Lofting plumb
line of door
opening width
Figure 2-11 Drawing of fixing landing 2-12 Alignment of center of sill door opening width line
door lower installation support and center of door opening width lofting plumb line
c) Adjust the left and right direction to make the center of sill door opening width and center
of door opening width lofting plumb lines which lie at each end of sill surface coincident as
figure 2-12 shows. Lock sill carrier groove slider bolts that connect sill support channel
and sill carrier firmly.
d) Adjust the distances between sill surface and the center of door opening lofting plumb
lines at two ends both to be 30 0+2 mm as shown in figure 2-13. Lock the bolts that
connected sill with sill carrier firmly.

Door opening
width lofting
Elevation plumb line Door opening width
offered by lofting plumb line
owner Door opening width
lofting plumb line
Decoration
completion surface Sill surface
Sill surface
Figure 2-13 Positions of sill and lofting plumb line
e) After adjusting, lock all fixed bolts firmly again and weld two points at the upper and lower
position between the big flat washer and support of expansion bolt. The overlap surface of
two supports needs to be welded also. Then weld the overlap part of sill carrier and lower
installation support. After welding finished, remove weld slag and brush rust-proofing paint
(paint no.: RAL7046) as shown in figure 2-14.
Sill carrier Sill
Landing door lower

Figure 2-14 Schematic drawing of welding sill support channel
2.6.5 Install landing door apron as figure 2-15 shows.

Cross recessed
countersunk head
Bolt M510
U-nut M5
Figure 2-15 Drawing of landing door apron installation

2.6.6 Install landing door jamb

Install the landing door jamb as figure 2-16 and 2-17.show.
Door lintel
Hexagon
socket head
bolt M8X16
Internal serrated
Right upright lock washer 8
Hexagon
socket head
Left bolt M8X16
Internal
upright
serrated lock
washer 8
Sill carrier
Figure 2-16 Schematic drawing of landing door jamb (center-opening double-leaf) installation

Door
Door
closing link
Light
barrier
Hexagon socket
head bolt M8X20 Link
Cross recessed
pan head tapping
Internal serrated
screw
ST3.5X9.5 lock washer 8 Door closing
upright
Flat washer 4
Upright
Hex bolt
M10X20
Hex flange Sill carrier

nut M10
Figure 2-17 Schematic drawing of landing door jamb (side-opening double-leaf) installation
2.6.7 Fix landing door jamb with wall as shown in figure 2-18.

M665
expansion
Hex bolt M616,
bolt
nut M6, flat
washer 6
Figure 2-18 Schematic drawing of installing landing door jamb

(center-opening double-leaf) with wall
2.6.8 Connect integrated pressure plate and link with bolts. Dont press the link with integrated
pressure plate tightly at first and keep 2~3mm clearance as figure 2-19 shows.
Integrated Link
pressure plate
Hexagon socket
head cap bolt
M816
Figure 2-19 Schematic drawing of installing integrated pressure plate with link

2.6.9 Check landing door triangular lock, hexagon socket head cap bolt M510 and big nut M20 of
triangular lock and fasten them. Then install the landing door device because if you install
landing door device first, you cant fasten it. See figure 2-20.
Hexagon socket
head bolt M510
Triangular lock
releasing rod support
Internal serrated lock
Triangular lock spring washer 5
Flat washer 5
Triangular lock big nut
Triangular lock shaft sleeve
Triangular lock core
Right side opening and

Right side opening
center-opening double-leaf
Figure 2-20 Schematic drawing of landing door triangular lock installation
2.6.10 Adjust landing door jamb

When installation is finished, the error of diagonals of door jamb A and B is 1.0mm and error of
upright front and back verticality C and D is not more than 2.0mm as figure 2-21 shows.
Figure 2-21 Schematic drawing of adjusting landing door jamb

2.7 Installation of landing door hanging components

At this time, adjusting the door guide rail levelness and straightness on the landing door hanging
components is the key element of installation quality. Ensuring that the door guide rail is parallel to sill is
the key element of landing door well operating. Therefore the adjustment must be accurate.
2.7.1 Install landing door upper installation support
Fix landing door upper installation support based on 2.5.2 landing door upper installation support
expansion bolt position as figure 2-22 shows.
Clear door opening

height + 255
Figure 2-22 Schematic drawing of installing landing door upper installation support
2.7.2 Install landing door hanging components

Hoist landing door hanging components into hoist-way and connect the components with upper
installation support as shown in figure 2-23.
Hex bolt
M820
Figure 2-23 Drawing of landing door hanging components installation
2.7.3 Install landing door hanging components with door jamb

a) Hang integrated guide rail groove of landing door hanging components on the door
jamb integrated pressure plate as figure 2-24 shows.

Guide rail groove of

Integrated landing door hanging
pressure plate components
Integrated
pressure plate
Figure 2-24 Drawing of installing landing door hanging
components with door jamb integrated pressure plate
b) Fix landing door hanging components with door jamb as figure 2-25 and 2-26 show.
Fasten bolt
with hex
wrench
Internal Hex bolt

serrated lock M816
washer 8
Figure 2-25 Drawing of installing landing door hanging components with door jamb
(center-opening double-leaf)

Hex bolt
M816
Internal
serrated lock
washer 8
Special hex thin

bolt M8 25
Figure 2-26 Drawing of installing landing door hanging components with door jamb
(side-opening double-leaf)
2.7.4 Adjust landing door hanging components

a) When landing door hanging components installation is finished, see figure 2-27.

Landing door upper

Landing door
hanging components
Door jamb
Sill
Door opening
width plumb line
Landing door lower

installation support Door opening
width plumb line
Figure 2-27 Drawing of landing door hanging components installation

(center-opening double-leaf)

b) Adjust the left and right direction of landing door hanging components and make the
center of door opening width and door opening width lofting plumb lines which at each end
of landing door hanging components align with each other as figure 2-28 shows.
Door opening width lines at

two ends of landing door
hanging components
Door opening
width lofting
plumb line
Figure 2-28 Drawing of connecting landing door Figure 2-29 Drawing of connecting landing door
hanging components with door jamb hanging components with door jamb
c) Adjust the distance between landing door hanging components guide rail and the center
of door opening width lofting plumb lines at two ends. The distance of center-opening
double-leaf landing door is A = 66.8 1mm and the distance of side-opening double-leaf
landing door is A = 66 1mm as figure 2-29 shows.
d) Adjust the distance between the bottom surface of landing door hanging components
guide rail and sill surface which is B = C = (clear door opening height + 60) 1mm as
shown in figure 2-30.
Figure 2-30 Drawing II of connecting landing door device with door jamb

2.8 Installation of landing door board and slider

2.8.1 For installation of landing door board and slider, refer to figure 2-31.
Special cup head

square neck bolt
M8 x 20

Hanger door bolts
Hex flange
nut M8
Square washer
Hex flange nut

M10
Hex bolt
M8 x 20
Standard spring
washer 8
Big flat washer
Door slider
Figure 2-31 Installation of landing door board and slider
2.8.2 Adjust landing door board

a) Leftward and rightward adjustment: position of the door board can be adjusted by
loosening four M8 flange hex nuts of the hanger door bolt kit as shown in figure 2-32.

Leftward and rightward adjustment
Figure 2-32 Leftward and rightward adjustment of landing door board
b) upward and downward and clearance adjustment: position of the door board can be
adjusted by loosening four M10 flange hex nuts of the hanger door bolt kit as shown in
figure 2-33.
Clearance adjustment between

door board and door pocket
Upward and downward
adjustment
Horizontal adjustment
Figure 2-33 Upward and downward adjustment of landing door board
c) Refer to figure 2-34 for door board requirement after adjustment.

Landing
door board
Door
pocket
Door board eccentricity Door board inclination

< 1mm < 1mm
Figure 2-34 Adjustment requirements for landing door board
2.8.3 Adjust eccentric wheel

Usually, clearance between the pulley and guide rail has been adjusted before delivery of the
pulley. If the clearance is found to be too large or too small during operations, it can be adjusted
by regulating the lower pulley (eccentric wheel).Correct adjustment: adjust the clearance
between the lower pulley (eccentric wheel) and the guide rail to be within 0.20.5mm, and then
lock M10 bolts. See figure M10.
Guide rail
The lower pulley

(eccentric wheel)
Figure 2-35 Adjustment of the eccentric wheel
2.8.4 Adjust verticality of door hanging board

After door board installation on the spot, if the door hanging board is found to be out of plumb, door
hanging board adjustment washers can be used appropriately to adjust verticality of the door
hanging board. See figure 2-36

Door hanging board

adjustment washers
Figure 2-36 Adjustment of the eccentric wheel
2.8.5 Adjust landing door lock

a) Loosen two M8 nuts on the limit rubber support and move the support gently to adjust the
center of the revolution axis to be 100mm away from the edge of the door hanging
board.Lock the nut as shown in figure 2-37.
Landing door lock
point
Resolution axis Door holder installation support
Nut M8
Figure 2-37 Adjustment diagram of landing door lock
b) Loosen two M6 (A, B) nuts on the limit rubber and rotate slowly the limit rubber screw M6
(A) to ensure that the engagement between the lock point and the contact switch support
is not less than 7mm when the door lock is closed completely, then lock nut M6 (A).Adjust
limit rubber screw M6 (B) and leave enough space to ensure that the lock point can be
release when the door is opened, then lock M6 (B) as shown in figure 2-38.

Door holder Cup head square neck

Contact switch Contact switch installation support bolt M6 x 16
Limit rubber M6 (A)
Limit rubber M6 (B)

Nut M6
Figure 2-38 Adjustment diagram of landing door lock (two)
c) Loosen two M6 nuts on the door holder fixing plate and move the fixing plate gently to
ensure that the center line of the two door holders is 145mm away from the edge of the
door hanging board.Lock the nut as shown in figure 2-39.
Door holder installation support
Door holder Nut M6

Nut M6 installation support
Door holder
Door hanging board
Door hanging
board
Figure 2-39 Adjustment diagram of landing door lock (three)
2.8.6 Position of landing door in closed state

Figure 2-40 Position of two side-opening landing doors in closed state.

Door closing
upright
Aluminum sill Landing door board
Landing
door board
Figure 2-40 Position of two side-opening landing Figure 2-40 Position of two side-opening landing
doors in closed state (figure one) doors in closed state (figure two)
Figure 2-41 Position of two center-opening landing doors in closed state.
Car landing door in closed state

Car

DoorDoor
widthWidth
Figure 2-41 Position diagram of two center-opening landing doors in closed state
Figure 2-42 Position of two center-opening landing doors in open state.
Car landing door in open state

Car
Door width
Figure 2-42 Position diagram of two center-opening landing doors in open state

Chapter III Maintenance Precautions

3.1 Wipe the guide rail of the landing door during each time of maintenance, check
wear extent of the door pulley and replacement should be made immediately if it
exceeds 1.5mm.
3.2 Check tension degree of the steel wire rope during each time of maintenance as
shown in figure 3-1.
Attention: When the compression length of the steel tensioning spring is checked to
exceed 171mm, first loosen two hex flange nuts M8, and then adjust the tensioning spring to be
171mm in length.
Steel wire rope Steel wire rope

Steel wire fixing plate tensioning plate
Tensioning
Tensioning bolt
spring
Steel wire rope wheel
Hex flange nut M8
Figure 3-1 Schematic diagram of steel wire rope tension adjustment
3.3 Degree of tightness of standard parts should be checked during each time of
maintenance.
3.4 Smoothness of the landing door lock actions should be checked during each time
of maintenance.
3.5 Correct application method of the triangle key.
Attention: Unlocking of the triangle lock of the landing door should comply with
the following procedures.
3.5.1 After opening the landing door, first determine the position of the car to prevent missing
your foot and causing falling accidents in case that the car is not in this floor;
3.5.2 Open the lighting at the landing doorway, clear all kinds of sundries and note that there
should be irrelevant personnel around;
3.5.3 Insert the triangle key into the unlocking hole and determine the unlocking direction;
3.5.4 The operating personnel should stand to keep the body center and then unlock slowly in the
unlocking direction;
3.5.5 After unlocking, push open the landing door to a seam of about 100mm, then take back the
triangle key and observe conditions in the well. Special attention should be paid that at the

moment the landing door cannot be pushed too open;
3.5.6 After completion of unlocking, the operating personnel should confirm that the landing door
has been locked securely.

Chapter IV Consumables of S200 Landing Door
Steel wire rope
Interlock switch
Door holder
Door hanging wheel
Door contact
Eccentric
wheel
Door slider
assembly
Figure 4-1 Schematic diagram of consumables of S200 landing door

Table 4-1 Table of consumables

Name Usage Remarks
Door hanging wheel 48 Landing door
Door slider assembly Landing door
Auxiliary contact of
Door contact AZ05(06)
landing door
Door opening type and door
Steel wire rope Landing door
width should be indicated
Eccentric wheel Landing door
Door holder Landing door
Main contact of landing
Interlock switch (socket/plug)
door

Chapter V Appendix
Installation checklist of landing door
Contract unit: Project name:
Contract No.: Factory order No.:
Elevator model: Elevator No.:
GAD No.: Installation date:
5.1 Overall installation confirmation of parts of landing door
Serial Actual
Requirements Solutions
No. conditions
1 Expansion bolts are fixed and locked
It is required that the site welding positions be welded
2
and painted after welding slag being removed

removal
38
Protective film
Connecting parts
Right
Project manager
door board 3-6mm
Door pocket
Clearance with landing

Left
2mm
Longitudinal verticality
2mm
Horizontal verticality
Signature:
5.2 Installation confirmation of landing door on each floor
lock roller and car sill 8-10mm
Date:
Distance between door
board and sill 3-6mm
Clearance between door
Landing door
and door pocket 3-6mm

No.: R000000251
Clearance between door board

boards 2mm
Clearance between two door
Inspector
1/600
Longitudinal verticality
1/600
Horizontal verticality
8-10mm
Distance from car gateway
Signature:
2mm
Deviation from car center
Date:
Landing door sill
Difference value
Right

0~2mm
width is 30mm
Leader of installation team

vertical line of door
Clearance with lofting
Left
Installation Manual
1-2mm
Height over the ground
1/600
levelness
requirements
Signature:
Standard
Floor
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
1
2
3
4
5
6
7
8
9
Date:

Installation Manual - S200 Landing Door System

Uploaded by

Copyright:

Available Formats

Installation Manual - S200 Landing Door System

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Installation Manual - S200 Landing Door System

Uploaded by

Copyright:

Available Formats

ThyssenKrupp Elevator (China)

Technical Information for Elevator Products

Installation Manual S200 Landing Door System

Edited by Alex Jin 2012-10-22

ThyssenKrupp Elevators (Manufacturing China) Engineering Center

ThyssenKrupp Elevator (China)

ThyssenKrupp Elevator (China)

Chapter I General drawing for S200 landing door system ................................................................. 2

Installation Manual No.: R000000251

Chapter I General Drawing for S200 Landing Door System

Figure 1-1 S200 landing door system (center-opening double-leaf)

ThyssenKrupp Elevator (China) 2

Figure 1-2 S200 landing door system (side-opening double-leaf)

ThyssenKrupp Elevator (China) 3

Upper installation Landing door hanging

Hanger door bolt kit

Door jamb and lintel

Landing door board

Door slider components

Door jamb upright

Lower installation support

Landing door sill

ThyssenKrupp Elevator (China) 4

Landing door hanging

Upper installation support

Hanger door bolt kit

Door jamb upright

Door closing side upright

Landing door board

Landing door sill

Landing door apron

ThyssenKrupp Elevator (China) 5

Chapter II Installation of S200 Landing Door System

2.2 Safety specifications

The signs below are used as safety identifications in the manual

Electric shock risk sign

ThyssenKrupp Elevator (China) 6

2.2.2 Safety measures applied in emergency situations

2.3 Preparation of installation tools

Name: wrench Name: circlip pliers Name: leveling rod

Name: plumb Name: socket wrench Name: hex wrench

Name: feeler gauge Name: cross screw driver

ThyssenKrupp Elevator (China) 7

2.4 Main parameters of S200 landing door system

ThyssenKrupp Elevator (China) 8

ThyssenKrupp Elevator (China) 9

Clear door opening width

Clear door opening width

2.5 Preparation before S200 landing door installation

Elevation line The distance is different

Figure 2-3 Schematic drawing of floor elevation line

ThyssenKrupp Elevator (China) 10

Clear door opening height + 255

Sill support channel

2.5.2 Expansion bolt installation for landing door installation

ThyssenKrupp Elevator (China) 11

M12100 expansion bolt Clear door opening width + 250

M665 expansion bolt