Catalogue

NESCO ELECTRICAL PRODUCTS
C A TA L O G U E
Portable Appliance Testing Equipment

Appliance Test Tags
Test Instruments
Workplace Safety Products
Automation & Control Products
Overhead and Underground Products
w w w. n e s c o . c o m . a u
NESCO
Electrical Products
TAKE A LOOK AT WHAT WE OFFER
Customer Service
Product Solutions & Systems
Research & Development

Product Training
Technical Support
Distribution
Australia Wide
Distribution Network
Local Representation
Marketing
Full Colour Product Catalogue
WEB Support
Full Colour PDF Product Sheets
Fax Friendly Documents
Product After Sales Backup & Service
Calibration Services
C ontents
www.nesco.com.au
TNT Series Testers

High precision testing and speed
Simple one button testing
Large graphic display
Pass/Fail indication plus actual test results displayed
Fast and easy to use
Recording of results and communication via
pocket PC (refer to pages 6 & 8)
Catalogue No. TNT NEW
Virtual Demo Available www.nesco.com.au
TNT Portable Appliance Tester

TNT+ Portable Appliance Tester
+ RCD Tester + Appliance Power Tester
Included Accessories
Carry bag, TNT XL-IEC fly lead, TNT EL-earth test lead,
Factory calibration certificate, Instruction manual. Catalogue No. TNT+
Optional Accessories
PDA & Software ( refer to next page) Australian made to comply with the requirements of AS/NZ3760:2001
Specifications common to TNT and TNT+

Tests Performed Measuring Range Test Voltage/Current Pass Level
Portable Appliance Tester
Earth Bond Test 0.0 to 15 200mA <1
Insulation Test 0.0 to 10M 250/500V Selectable >1M
Polarity Test Pass / Fail
Mains Supply Test
A-N-E LEDs
Communication and recording via Pocket PC (see pages 5 & 7)
Specifications TNT+ Only
RCD Tester
Trip Current 2 - 500mA 5mA steps
Trip Time 0 - 2500ms 0001s
Current Ramp Trip Test 2 - 500mA 2mA steps
Battery Backed Display 20 seconds after trip
Load Tester
Leakage Current 0.0 to 1999.9mA set fail limit 5mA
Load Current 0.0 to 10A (Res)
Voltage 0 - 300VAC
Power Factor 0.000 to 1.000
Apparent Power 0 - 2999VA
Power 1 - 2999 W
2
TNT Series Options and Accessories
Specifications
Part No. Description
TNT Portable Appliance Tester, with Carry Bag
TNT+ Portable Appliance Tester with RCD Test +

Power Measurement Catalogue No. TNT ES-500
Common options for above
TNT ES-500 Earth Strap, 500mm long
TNT 3PADP 3 Phase Adaptor lead for TNT or TNT+
TNT EL Earth Lead with Croc Clip
TNT XL Extension Lead Adaptor (IEC - 3 Pin Plug)
TNT CAL Calibration Certificate for TNT
TNT+ CAL Calibration Certificate for TNT+
TNT ISOT Isolation Transformer, Fused with handle Catalogue No. TNT ISOT
socket and lead
TNT-TTP Thermal transfer printer for printing test tags on site

(requires WinPATS LITE and Laptop or PC)
TNT-PDAPACK H2210 Pocket PC, WinPATS CE, TNT-BCS Scanner, TNT-

CMPC Comm Adaptor, TNT-PDASC Serial Cable C/W
Protective Holster
Catalogue No. TNT-TTP
Software and Communications
WinPATS CE Testing and Recording Software for PocketPC (PDA)
WinPATS Lite Testing and Recording Software for Desktop/

Laptop PC
TNT-CMPDA Interface Connector for TNT/TNT+ and PDA

(serial cable required)
TNT-CMPC Interface Connector for TNT/TNT+ and PC

(serial cable required)
1021-USB Barcode Scanner for USB port used with LAPTOP PC

Catalogue No. H2210
PPT2800 Industrial PDA with in-built Barcode Scanner
Industrial PocketPC device (weatherproof, impact
resistant with Laser Scanner built in
Catalogue No. TNT-BCS
For complete specification see our website www.nesco.com.au

3
www.nesco.com.au
MARTINDALE MicroPAT+
Features
Rugged design
Test results are stored in the built-in memory and by using the
optional software package test results can be downloaded
to a personal computer
RS-232 interface for barcode input and data output
Performs
Earth continuity test 0 to 19.99
100mA, 10A, 25A test current
Insulation test 0 to 19.9M
500V DC test voltage
Run test 240V mains / AC supply
Earth leakage test 0 -6mA AC
Flash test 0 - 30mA AC
1.5kV A.C. - Class I
3kV A.C. - Class II
Catalogue No. MicroPAT+
Mains lead 1.7 mtr, earth continuity lead 1.5 mtr c/w heavy
duty crocodile clip, flash test gun, instruction manual,
extension lead adaptor.
1021+ Barcode scanner
WinPATS Lite Windows recording software (see page 6) Catalogue No. 1021 SER
TESTING AND INSPECTION INTERVALS TABLE 4 NOTES:

1 The actual sub-environment in which the equipment is located determines the row for the environment
to be used in Table 4. e.g. A computer in a non-hostile environment in an office within a factory would
attract a test/inspection action in accordance with Row 3.
2 Regulatory authorities, other Standards, workplace safety requirements or manufacturers

instructions may specify intervals appropriate to particular industries or specific types of
equipment.
3 RCDs in transportable equipment shall be regarded as portable RCDs
4 The following Standards refer only to the inspection and testing method of Clause 2.3 of this Standard,
but not to the intervals of testing in Table 4 above. Refer to the appropriate
Standards for specific test intervals:
AS 1674.2 Safety in welding and allied processes - Electrical
AS/NZS 3001Electrical installations Re-locatable premises (including caravans and tents) and their site installations
AS/NZS 3002Electrical installations Shows and carnivals
AS/NZS 3003Electrical installations Patient treatment areas of hospitals and medical and dental practices
and dialysing locations
AS/NZS 3004Electrical installations Marinas and pleasure craft at low voltage
AS/NZS 3012Electrical installations Construction and demolition sites
AS/NZS 4249Electrical safety practices Film, video and television sites
EXTRACT FROM AS/NZS 3760:2003

STANDARDS AUSTRALIA / STANDARDS NEW ZEALAND
4
TABLE 4
Testing and inspection intervals for electrical equipment
(CAUTION: This page must be read in conjunction with the Standard as a whole, and particularly Clause 2.1)
Specifications
Interval between inspection and tests
Class of equipment Residual Current Devices (RCDs)
Operating Cord
Class I
Class II Push-button time and push - sets and
Type of environment and/or (protectively (double test - by user button test power
equipment earthed) insulated) Portable Fixed Portable Fixed boards
(a) (b) (c) (d) (e) (f) (g) (h)
1 Factories, workshops, places 6 12 Daily, or 6 12 12 6
of work or repair, mths mths before every mths mths mths mths
manufacturing, assembly, use, whichever
maintenance or fabrication is the longer
2 Environment where the 12 12 3 6 12 12 12
equipment or supply flexible mths mths mths mths mths mths mths
cord is subject to flexing in
normal use OR is open to
abuse OR is in a hostile
environment
3 Environment where the 5 yrs 5 yrs 3 6 2 yrs 2 yrs 5 yrs
equipment or supply cord is mths mths
NOT subject to flexing in
normal use and is NOT open
to abuse and is NOT in a
hostile environment
4 Residential type areas of: 2 yrs 2 yrs 6 2 yrs 2 yrs 2 yrs
hotels, residential institutions, mths 6
motels, boarding houses, mths
halls, hostels accommodation
houses, and the like
5 Equipment used for 6 12 3 N/A 12 N/A 12
commercial cleaning mths mths mths mths mths
6 Hire equipment:
Inspection Prior to hire Including N/A N/A Prior to
push-button hire
test by hirer
prior to hire
Test and tag 3 mths N/A 3 mths 12 mths 3mths
7 Repaired, serviced and After repair or service which could affect electrical safety, or on reintroduction
second-hand equipment to service.
EXTRACT FROM AS/NZS 3760:2003

STANDARDS AUSTRALIA / STANDARDS NEW ZEALAND

5
www.nesco.com.au
WAVECOM WinPATS CE / WinPATS lite

NESCO brings to you and your company a new level of convenience
and portability in mobile data collection. In conjunction with Wavecom
Instruments we have combined many compact computing technologies
to provide you with revolutionary methods of improving productivity
and profitability.
The TNT T and TNT+ introduced a new level of simplicity and

functionality to the field of appliance testing and now with the
latest G2 (second generation) testers these units can be interfaced
with both a standard PC using WinPATS lite & with a PDA (PocketPC)
using WinPATS CE.
If the PDA (Pocket PC) is also fitted with a barcode scanner, the entire
testing process can be virtually completely automated with no operator
data input required.
Simple steps are
1. Scan in barcode and appliance details
2. Plug appliance into to test, scan OK on the PDA and let

the tester do the rest.
3. The test results are stored into the Pocket PC.
Once the days/weeks work is done synchronise the pocket PC

with WinPATS lite on your desk top or laptop and the database
is then automatically entered and updated. All you need to do
then is print your reports.
WinPATS CE E controls the TNT / TNT+ and stores the results obtained
and with the functionality of a PocketPC, all other relevant data can
be entered directly into the application rather than manual notes
Catalogue No. WinPATS CE
having to be used for entry later into a database.
WinPATS lite is the main database which provides the full record
keeping and reporting functions and can be updated either manually,
from WinPATS CE (via a PocketPC with appropriate synchronisation
software) or from any data storage type PAT unit such as the MicroPAT+.
Complete packages including PDAs can be supplied, please contact

NESCO sales for details.
Catalogue No. WinPATS Lite
6
AS/NZS 3760
and AS/NZS 3012 which provide guidelines for testing and should be
taken as minimum requirements for this work as these documents are
generally referred to in the relevant legislation in each of the states.
Overview Of Systems
The TNT, TNT+ and the MicroPat+ can be used as stand alone testers
or they can be part of powerful intergrated systems. These are flexible
and scaleable packages utilising modern technologies to provide
efficient and error free data entry and testing. With systems to suit
virtually every business, no matter how large or small.
1021 SER Barcode Scanner

The introduction of barcode scanners are making the task even easier
by allowing an appliance ID number to be allocated to a single item
and a barcode label or tag applied to assist with fast and accurate
data input.
Using barcodes and integrating the safety testing process with an

ongoing asset management regime assists in giving the customers
traceability on their plant and equipment. This code gives reference to
the item when downloaded to the Software program by assigning an
Portable appliance ID to the item it gives provision to trace this item through
Appliances MicroPAT+ site and location within site.
Bar Code Tags

1021 SER
Micro PAT+
This unit performs insulation and continuity tests along with a run
test, leakage test and finally a flash test. This unit performs class I,
Extension class II tests as well as extension leads and can be downloaded to
Leads a PC. This unit differs from the TNT series in that the results from up
to 1000 tests can be stored in memory for download at a later date.
This is particularly useful if the customer is constantly moving around
a site testing equipment.
Appliance Failed Faulty Appliance Test Tags
FAST
Appliance Passed
PC
TT TM TA
Appliance Test Tags
WinPATS is designed for use with the Micro PAT+ . This allows the
user to capture test results from these units and assign sites, locations
within sites, asset numbers if needed as well as giving the provision
of managing and reporting on individual appliances regarding test
history fault levels and specifications. There is also the provision for
Printer reporting and certificate issue through this software.
7
www.nesco.com.au
TNT
The TNT is capable of testing insulation, earth bond and displaying the
actual test result. Polarity and mains supply connections are indicated
Portable by l.e.d.s. This unit is capable of testing class I, class II, appliances and
Appliances
also comes with an adaptor for extension leads. The unit gives an
actual test result as well as a pass/fail indication on screen and has
the facility to communicate with a PC.
TNT TNT+
The TNT+ performs the same functions as the TNT but with the added
Extension Leads advantages of being able to test and record RCD trip current and time,
as well as load testing incorporating leakage current, load current,
voltage, power factor and power in watts. As with the TNT this unit
also provides the capability of downloading test results to a PC.
Appliance
Failed
RCDs TNT+
FAST
Appliance
Passed
TT TM TA
Portable Isolation Appliance Test Tags
RCDs Transformer
TNT ISOT Socket Bar Code
Scanner
PC in Office Office Printer
Communication
Option 1
PDA
WinPATS
Lite
1021 USB
Communication
Option 2
Laptop Test Tag Printer
WinPATS
Lite
8
A p p l i a n ce Test Tag s
EELB FAST MP
Electrical Equipment Log Book Faulty appliance safety tag NESCO Marking Pen
100 Pages Pack of 50 suits all NESCO Tags.
Writes on most surfaces.
Catalogue No. EELB
Catalogue No. FAST Catalogue No. MP
RCDLB RCDTT TTCW

NEW
RCD Log Book RCD tag Construction Wiiring Tags
100 Pages NEW Pack of 100 Used to identify temporary
wiring on construction sites.
Catalogue No. TTCW-100 pack of 100

Catalogue No. RCDLB Catalogue No. RCDTT TTCW-1000 roll of 1000
Custom Test Tags - see pages 11 & 12 for custom sheets

All Nesco test tags may be customised to suit individual companies uses.
TA/TN-custom
Include company logo, phone and fax numbers, e-mail and web addresses.
Box layout can be changed. Talk with our sales staff for other options.
Catalogue No. TA/TN-custom
TM-custom
Box layout can be changed. Sequential inspection numbers can be requested.
Talk with our sales staff for other options.
Catalogue No. TM-custom
TT/TTN-custom
Box layout can be changed up to three colour printing available.
Sequential inspection numbers can be requested. Talk with our sales
staff for other options.
Catalogue No. TT/TTN-custom

9
www.nesco.com.au
Ap p lian ce Test Tag s
TA/TN-series
The leading test tag for industrial and construction areas. This is an industrial
quality tag complete with marking pen and security clips. OWNER
COMPLETE WHERE APPLICABLE
NEXT TEST DUE
/ /
CAUTION
AUSTRALIAN MADE
c COPYRIGHT ALL RIGHTS RESERVED RED JAN MARCH
GREEN APR JUNE PLANT NUMBER TEST DATE
DURACK PTY. LTD.
REDG. DES. NO. 110703 BLUE JUL SEPT
/ /
NSW ONLY
TA-1 Red Jan-March TN-1 Red Jan/Sep
YELLOW OCT DEC
SIGNATURE LICENCE
OWNER NEXT TEST DUE
PLEASE INFORM YOUR ELECTRICAL SERVICES IF THIS APPLIANCE IS DEFECTIVE IN ANY WAY
/ /
CAUTION
AUSTRALIAN MADE
PLANT NUMBER TEST DATE
TA-2 Green April-June TN-2 Blue Feb/Jul

GREEN APR JUNE
DURACK PTY. LTD.
REDG. DES. NO. 110703 BLUE
YELLOW
JUL
OCT
SEPT
DEC
/ /
SIGNATURE LICENCE
OWNER NEXT TEST DUE
TA-3 Blue July -Sept TN-3 Orange Mar/Nov / /
CAUTION
AUSTRALIAN MADE
DURACK PTY. LTD.
REDG. DES. NO. 110703 BLUE
YELLOW
JUL
OCT
SEPT
DEC
/ /
SIGNATURE LICENCE
TA-4 Yellow Oct-Dec TN-4 Green Apr/Aug OWNER

NEXT TEST DUE
/ /
CAUTION
AUSTRALIAN MADE
DURACK PTY. LTD.
/ /
TA-5 Orange 6 Monthly Jan-June TN-5 White May/Dec
BLUE JUL SEPT
REDG. DES. NO. 110703
YELLOW OCT DEC
SIGNATURE LICENCE
TA-6 White 6 Monthly July-Dec TN-6 Yellow Jun/Oct

TA-7 Black Yearly TN-R Rainbow 17 each of above colours Catalogue No. TA/TN-series
TA-8 Burgundy 5 Yearly TN0B Black (no legend)
TA-R Rainbow 25 each of red, green, blue, yellow
TM-series
OWNER OWNER OWNER OWNER
Heavy Duty tag using the highest quality adhesive. Suitable for use in all L I C N o. L I C N o. L I C N o. L I C N o.
environments. Also available as a barcode tag. TESTING COMPANY TESTING COMPANY TESTING COMPANY TESTING COMPANY
Mitay Ser vices Pty. Ltd.

Mitay Ser vices Pty. Ltd. Ltd. Ser vices Pty. Ltd.
Mitay Ser vices Pty. Mitay
c All Rights Reser vedc All Rights Reser vedc All Rights Reser ved c All Rights Reser ved
CAUTION CAUTION CAUTION CAUTION

TM-1 Red Jan-March TM-6 White 6 Monthly July-Dec ENSURE TEST IS CURRENT
Insp.
No.
ENSURE TEST IS CURRENT
Insp.
No.
BEFORE OPERATING BEFORE OPERATING BEFORE OPERATING BEFORE OPERATING
Insp.
No.
Insp.
No.
RED JAN MARCHRED JAN MARCH RED JAN MARCH RED JAN MARCH
GREEN APR JUNE
GREEN APR JUNE GREEN APR JUNE GREEN APR JUNE
TM-2 Green April-June TM-7 Black Yearly NEXT TEST DUE

YELLOW
BLUE JUL
OCT
SEPT BLUE
DEC
YELLOW
NEXT TEST DUE

JUL
OCT
SEPT
DEC YELLOW
BLUE
NEXT TEST DUE

JUL
OCT
SEPT
DEC YELLOW
BLUE
NEXT TEST DUE

JUL
OCT
SEPT
DEC
/ / / / / / / /
TM-3 Blue July -Sept TM-8 Burgundy 5 Yearly T E S T D AT E
/ /
T E S T D AT E
/ /
T E S T D AT E
/ /
T E S T D AT E
/ /
P L A N T N o. P L A N T N o. P L A N T N o. P L A N T N o.
TM-4 Yellow Oct-Dec TM-R Rainbow 25 each of red, green,

TM-5 Orange 6 Monthly Jan-June blue, yellow Catalogue No. TM-series
TT/TTN-series / /
Test Date
/
Next Test Due
/
Licence No. / / Plant No. / /

Next Test Due Test Date
Supplied in packs of 100 with marking pen. Suitable for indoor and office use. service contact:
Licence No. / /
Plant No.
For
/ /
Next Test Due Test Date
Also available as a barcode tag. 1234567 / / / Plant /
Licence No.N o . No.
Insp.
service contact: For
Test Date Next Test Due
TT-1 Red Jan-March TTN-1 Red Jan/Sep NSW ONLY CAUTION

Ensure test is current
1234567 Licence No.N o .
Insp.
Plant No.
Before operating
For service contact:
TT-2 Green April-June TTN-2 Blue Feb/Jul NESCO (07) 3274 2466
CAUTION
BY DURACK P/L
1234567 No.
For serviceI ncontact:
sp.
Before operating
TT-3 Blue July -Sept TTN-3 Orange Mar/Nov NESCO (07) 3274 2466
CAUTION
BY DURACK P/L 1234567 No.
Insp.
Before operating
TT-4 Yellow Oct-Dec TTN-4 Green Apr/Aug NESCO (07) 3274 2466 BY DURACK P/L
CAU TION
Before operating
TT-5 Orange 6 Monthly Jan-June TTN-5 White May/Dec NESCO (07) 3274 2466 BY DURACK P/L
TT-6 White 6 Monthly July-Dec TTN-6 Yellow Jun/Oct

TT-7 Black Yearly TTN-R Rainbow 17 each of above colours
TT-8 Burgundy 5 Yearly TT0B Black (no legend)
TT-R Rainbow 25 each of red,
green, blue, yellow Catalogue No. TT/TTN-series
TT-OF Optical Fibre Tag

Used to identify cable source and destination
Pack of 100
Catalogue No. TT-OF
10
Test Tag Customisation Sheet
TT-Series
Please re-write clearly any text you require:
Number of
Phone packs required
Mobile (Min 5 packs per colour)
Fax Red ( )
Address Green ( )
Blue ( )
Yellow ( )
Licence No. Orange ( )
Other text White ( )
Black ( )
Burgundy ( )
(Logo to be supplied on business card, letterhead or
suitable electronic file. Photocopies cannot be used.)
TM-Series
Number of
Fax Red ( )
Address Green ( )
Blue ( )
Yellow ( )
Black ( )
Burgundy ( )
TM-Series
Number of
Fax Red ( )
Address Green ( )
Blue ( )
Yellow ( )
Black ( )
Burgundy ( )
11
www.nesco.com.au
Ap p lian ce Test Tag s
Test Tag Customisation Sheet NSW

TT-Series
Number of
Fax Red ( )
Address Green ( )
Blue ( )
Yellow ( )
Black ( )
Burgundy ( )
TM-Series
Number of
Fax Red ( )
Address Green ( )
Blue ( )
Yellow ( )
Black ( )
Burgundy ( )
TM-Series
Number of
Fax Red ( )
Address Green ( )
Blue ( )
Yellow ( )
Black ( )
Burgundy ( )
12
Te s t I n st r u m en t s C alib rati on
Calibration
Calibration of test eqipment is the only means of establishing and proving that measurements obtained using that
equipment are correct. This does not mean that un-calibrated test equipment is inaccurate but without any proof
of an instruments accuracy, there is no way to confirm that readings taken are in fact correct.
The process of having equipment calibrated is primarily to confirm that the equipment concerned is accurate
within the manufacturers specifications and establishes taceability to known standsards by using commensurately
higher spcification equipment to test against, all of which of course has its own calibration to confirm its status.
Traceability is established only with correct certification and effectively compares individual items against national
and international standards.
NESCO is able to offer traceable calibration certificates with virtually all instruments sold, please consult with
our sales department for additional information.
SEW Insulation Tester Checker

The ITC8 can be used to check the calibration of resistance ranges
of insulation testers and multimeters.
Optional
The ITC8 can also be ordered complete with a NATA traceable
calibration certificate Catalogue No.ITC8CERT
Specifications
Measuring Range Catalogue No. ITC8
0.5,
1
, 2
, 20
, 200
, 1k
, 10k
, 20k
, 100k
, 1M
, 2M
, 10M
Accuracy
+/- 0.05 & +/- 2% (0.5 to 2)

& (20 to 10M)

Transmille Electrical Instrument Test Box

Provides the quick, cost efficient solution for the requirement to regularly
check test instruments.
Checks Insulation Testers

3 Insulation resistor values 1M, 9.9M, 99M (1% Accuracy)
Led indication of test voltage output at 100V, 250V, 500V, 1000V
3 Continuity resistor values 0.5 ,2 ,10 (1% +/-20m Accuracy)
AC Line voltage output for testing voltage measurement
Checks RCD Testers

Functional check of RCD testers via dedicated 10A socket
3 Selectable ranges: 10mA @ 150ms, 30mA @ 150ms, 150mA @30ms
Indicators for Ready Tripped - Overcurrent
Checks Loop Testers

Functional check of Loop testers via 10A socket
Supply loop impedance
Supply loop impedance + 1 offset (5% Accuracy)
Dimensions 28cm x 22cm x 9cm
Calibration certificate available on request. Catalogue No. 2080

13
www.nesco.com.au
Tes t Ins trum e n t s Test In st r u m en t s
MARTINDALE 250/500/1000V
Digital Insulation Tester
Large 4,000 count backlit digital display with analogue bar graph.
Measures insulation resistance, AV/DC voltage, continuity and resistance
of electrical circuits.
Automatic zero adjust removes the resistance of the test leads.
Output test voltage is displayed during testing.
For higher accuracy testing polarisation index and dielectric absorption
ratio functions are provided.
Batteries, test leads, instruction manual, carry case
Specifications
Function Measuring Range
M 250V
500V
1000V
AC/DC V 600V
Resistance 0.1 2,000M
Continuity 0.01 40
Catalogue No. IN2103
SEW 250/500/1000 Volt Analogue Insulation Tester

High powered, high quality analogue insulation tester
3 Low resistance range
Live Circuit warning beeper & indication.
Automatic safety discharge once the test is completed.
Displays AC voltage measurement of mains supply. 5 YEAR
Included Accessories WARRANTY
TL-24 test leads, 1 x 0.25A 250V fuse, instruction manual,

8 x AA batteries, carry strap.
Specifications
Function Measuring Range Scale
M 1000V 0-400M
500V 0-200M
250V 0-100M
ACV 0-600V -
Resistance 0-3 -
0-500 -
Catalogue No. 1832IN
14
In su lat io n Te sters
KAISE 500/1000V Analogue Insulation Tester

High accuracy testing
Timer switch enables continuous measurement, up to 3 minutes
Live line detection
Displays AC measurement of mains supply
Dust proof & water resistant case
TL-5 test leads, 6 x AA batteries, instruction manual, carry strap.
Specifications
M 500V, 1000V 100M & 200M
ACV 0-600V -
Resistance 0-50 -
Continuity Buzzer sounds less than 20 - Catalogue No. SK-3015
Metrohm 5kV Analogue Insulation Tester

Can be operated from internal rechargeable batteries or from an external AC supply
Housed in a rugged moulded plastic case
Detachable lid protects the front panel and provides storage for test leads
Battery Indication
DFK0075/A test leads, mains power supply lead, internal 12v NiCad Pack,
instruction manual
Specifications
M 500V, 1KV, 2.5KV, 5KV 100k to 100G
ACV 1000V AC - Catalogue No. E3511

15
www.nesco.com.au
I n s ula tion Tes t e r s Test In st r u m en t s
AEMC 5KV Digital / Analogue Insulation Tester

Programmable test run times and Pl ratio times
Selectable smooth function enables digital filtering to stabilize readings
Direct measurement and display of capacitance and leakage current.
Display resistance, test voltage and run time
Large dual backlit display with time, voltage and measurements shown.
Auto power-down when not in use
Designed to protection class 61010-1 1000V Cat III
Rugged weatherproof field case.
Accessory bag, test leads c/w 5kV rated hippo clips, rechargeable battery, power cord and user manual.
Model 5060 also includes Data View Lite software and cables for downloading
Specifications
Models 5050 5060
Test Voltage 500V 20k to 2000G

1000V 40K to 4000G
2500V 100K to 10,000G
5000V 200K to 10,000G
Voltage (selectable) 50 to 1000V / 10V increments 1000 to 5000V / 100V increments
Voltage Test/ Safety Check 0 to 1000V AC/DC
Power Source AC or DC with 8 x NiMH

rechargeable `batteries
Storage of readings over time 4kB memory 128kB memory
Storage of test results 20 Readings 128kB memory with RS-232
PC Application Software No Yes (included)
Report Generation Yes
Catalogue No. 5050

16
Electromate Voltage & Continuity Probe Tester
AC/DC voltage indication up to 600V
Continuity test audible & visual
Voltage display fully operational even without batteries
Internal basic load can be used for RCD tripping
Single pole test for phase detection
2 x AAA batteries
Designed to
Specifications Protection Class
IEC 61010-1
600V
Display 10 Leds Category III
Voltage 12 .690V AC/DC
Single pole 100690V AC Catalogue No. 7090
Electromate Basic DMM

Digital multimeter in a handy compact housing
Temperature measurements up to 1000C using thermocouple
K-type sensor (supplied with wire probe type-K sensor
for measurements up to 250C)
Holster, wire temp probe, 9V battery
Specifications
Voltage 500V AC/DC
Current 200mA DC
Resistance 2M
Temperature -40C to 1000C
Continuity Buzzer Catalogue No. 7241
SANWA Pocket DMM

Loaded with functions . Auto power off.
Case holder, instruction manual
Specifications
Voltage 500V AC/DC
Resistance 40M
Capacitance 200F
Frequency 99.99kHz
Continuity Buzzer sounds at less than 60 Catalogue No. PM3
17
www.nesco.com.au
M ultim e te rs Test In st r u m en t s
SANWA Analogue Multimeter

When the meter is not in use the test leads
& the front is protected by a hard cover.
Null (zero centre) meter in DC V
Drop and shock resistant meter.
TL-21 test leads, carry strap, instruction manual,
2 x AA batteries
cover closed
Specifications
DCV 1000V
ACV 750V
DCA 0.25A
Resistance 200M
Capacitance 10F
Catalogue No. YX-360TRF
SANWA DMM with Holster Designed to

Protection Class
A rugged DMM that feels good to use IEC 61010-1
Large LCD with a curved bar graph 600V

Category III
Auto power off
TL-21 test leads, holster, instruction manual
Catalogue No.CC1 Electromate carry case
Specifications
ACV 750V
DCV 1000V
Current 12A AC/DC
Resistance 2M
Continuity Buzzer sounds less than 20
Diode open voltage 3V
Catalogue No. CD721
18
NEW
SANWA DMM with Hard Case Protection
Versatile digital multimeter
Unique clip on hard front protective cover.
Designed to
Included Accessories Protection Class
IEC 61010-1
Instruction manual
600V
Optional Accessories Category III
Specifications
DCV 500V
ACV 600V
Resistance 40M
Capacitance 100F
Frequency 100kHz
Current 400mA AC/DC
Continuity Buzzer sounds 10 - 80
Duty 10 90%
Diode Test Open voltage approx.1.5VDC Catalogue No. CD800A
SANWA Industrial DMM

Versatile measurement range with great accuracy
Auto power off
Alarm warning for incorrect insertion of leads into the current
terminals if the meter is set on the wrong function
Holster, TL-82 test leads, K-type thermocouple, instruction manual
Test Leads, Carry Cases & Accessories (page 37 & 38)
Specifications
Voltage 1000 AC/DCV
Current 10A AC/DC
Resistance 40M
Continuity Buzzer sounds between 5 and Designed to
120 Protection Class
IEC 61010-1
Capacitance 3000F
600V
Frequency 1MHz Category III
Temperature -20 to 300C

-4 to 572F
Catalogue No. RD700
Diode Test Open voltage approx.3V TRMS MODEL Catalogue No. RD701
19
www.nesco.com.au
M ultim e te rs Test In st r u m en t s
Designed to
Protection Class
SANWA High Standard DMM PC Series IEC 61010-1
600V
Included Accessories Category III
Instruction manual, holster, TL-82 test leads, (PC510 only K-type thermocouple)
With (KB-RS2) cable and (PC Link/PC or PC Link Plus) software, measuring
data is transferred to PC through RS232 port for data logging.
SANWA PC500 High Accuracy DMM

SANWA PC510 High Accuracy TRMS DMM Catalogue No. PC500
(Temperature Measurement)
Designed to
Protection Class
IEC 61010-1
SANWA PC5000 4 Digit TRMS DMM Advanced Features
600V
Category III
Specifications
Function PC500 PC510 PC5000
TRMS -
Max/Min recording -
Voltage AC - -
(AC+DC)
Current (AC +DC) - -
Temperature - -50C to 1000C -

Catalogue No. PC510
Basic accuracy 0.08% 0.08% 0.03%
Display 5000 counts 5000 counts 50,000 counts
Voltage 1000V AC/DC 1000V AC/DC 1000V AC/DC
Current 10A AC/DC 10A AC/DC 10A AC/DC Designed to

Protection Class
IEC 61010-1
Resistance 50M 50M 50M
600V
Capacitance 9999F 9999F 9999F Category III
Frequency 5Hz to 125kHz 5Hz to 125kHz 5Hz to 200kHz
Continuity Buzzer operates operates operates 20120

20120 20120
%4 to 20mA - - 4mA(%) to 20mA(100%)
Logic Frequency - - 5Hz to 2MHz
Indicates included functions Catalogue No. PC5000
PC-LINK
Sanwa management software
KB-RS2
Downloading cable
Catalogue No. PC-LINK Catalogue No. KB-RS2

20
C lam p Meters
MULTI Leakage Clamp Meter

Wide range of digital current measurements (0.01A 300A AC)
40mm CT enables both leakage current and line current measurements
Compact size only 162mm long
Auto power off
Data hold
Carrying case, instruction manual, 2 x LR44
Specifications
Function Measuring Range Resolution
A AC 30/300mA 0.01mA AC
30/300A 0.01A AC Catalogue No. 140
MULTI Mini Digital AC/DC Clamp Meter

Wide range of digital current measurements (0.01A 200A AC/DC)
30mm CT
Suitable for low current measurement in both AC and DC
Ultra compact size only 146mm long
Carrying case, instruction manual, 2 x LR44
Specifications
A AC 20 A AC 10mA
200A AC 100mA
A DC 20 A DC 10mA
200A DC 100mA Catalogue No. 240
SEW 1000A AC/DC Clamp Meter

Very versatile digital meter
Auto ranging voltage, current and resistance functions.
Data hold
400mm conductor size
TL-3A test leads, carrying case, instruction manual, 1 x 9V battery
Specifications
ACA 400/1000A
DCA 400/1000A
ACV 400/600V
DCV 400/600V
2000
Buzzer Sounds less than 100 Catalogue No. 3800CL
21
www.nesco.com.au
Cl a m p M e te r s Test In st r u m en t s
SEW
W 300A AC Analogue Clamp Meter
Low cost clamp meter
Only one scale in the display window at a time to avoid reading errors.
38mm conductor size
TL-3A test leads, carrying case, instruction manual, 1 x AA battery
Specifications
ACA 6/15/60/150/300A
ACV 300/600V
DCV 75V
2000
Catalogue No. ST-375
SANWA 400A Clamp Meters Catalogue No. DCM400 & DCM400AD
Professional clamp meters
25mm conductor size

Data hold, range hold
DCA on DCM 400AD
TL-82 test leads soft carry case,
instruction manual, 2 x AAA batteries
SANWA 600A AC Clamp Meters

Great value
30mm conductor size

Data hold
TL-82 test leads (DCM60L only) soft carry case, Catalogue No. DCM60 & DCM60L
instruction manual, 2 x AAA batteries
Specifications
Function DCM400 DCM400AD DCM60 DCM60L
Current
ACA 40/400A 40/400A 20/200/600A 200/600A
Voltage
DCA - 40/400A - -
ACV 400/600V 400/600V - 600V
Frequency
(A) 20-4k 10kHz - - -
(V) 4k/40k/400k/1MHz - - -
Resistance
400 400 - 200
22
SANWA 2000A AC/DC Clamp Meter

55mm conductor size
TL-82 test leads carry case, instruction manual, 2 x AAA batteries
Specifications
AC/DCA 40/400/2000A
AC/DCV 400m/4/40/400/600V
Frequency 100/1k/10k/100k/1000kHz
Resistance 400/4k/40k/400k/4000k/40M Catalogue No. DCM2000AD
MULTI Large Jaw 3000A Clamp Meter

Huge CT 108mm jaw opening
Measures TRMS AC current and leakage current
Data hold and filter function
Auto power off
Instruction manual, carry case, 2 x AAA batteries
Specifications
AC current 0.1mA to 3000A Catalogue No. MCL-1100D
Electromate DMM / Open Jaw

Current Measurement NEW
Features two LCD displays
Auto power off
Data hold for each display
Duty cycle and diode test
AC current display always functional
Blister packaged, TL-3A test leads, 2 x AA batteries
Specifications
Current 200A AC
Voltage 600V AC/DC
Resistance 0.1 to 40M
Capacitance 1pF to 200F
Frequency 0.001Hz to 9.999MHz
Catalogue No.DT2001
23
www.nesco.com.au
Sp e c ia l P urp o s e
Meters & Accessories Test In st r u m en t s
SEW RCD Tester Measures Tripping Time

Accurate digital readout of disconnection time.
Measures line to earth voltage
Select testing at 0 or 180
Main supply correct polarity indication by LEDs
Indicates % error from input voltage fluctuation
Instruction manual, TL-EL 3 pin test lead, shoulder belt, 8 x AA batteries
TL-30 test leads
Specifications
Fault Test Current 3-500mA
Catalogue No. 1812EL
Electromate RCD Tripper

Low cost
Wiring check by LEDs
Test current range 10 35mA
The RCD tripper is designed to trip RCDs of 30mA rating or less

while giving mains supply check by way of LED indicators.
Catalogue No. S-1602
24
SEW Loop Impedance Tester
The complete electrical network can be analysed by scrolling through the results.
Bad contacts, old wiring or bad earth paths are quickly identified.
User manual, TL-30 and TL-EL 3-pin test lead, shoulder belt, 8 x AA batteries
Specifications
Loop Impedance L-E, L-N 0.03 to 2000
Test currents in each loop 11.76A at 230V
Voltage L-N, L-E 50 to 230V
Earth resistance 0.01 to 2000
Neutral, Line Resistance 0.01 to 2000
PSC Current L-N, L-E 6kA at 230V
Catalogue No. 1826NA
HT ITALIA SPEEDTEST RCD and Loop Impedance Tester

Multifunction instrument that checks manually or automatically tripping times
and currents of general and selective RCDs type A and AC, also total earth
resistance, line and fault impedance with calculation of prospective short
circuit current and phase sequence indication.
Innovative Loop Impedance Test Function

A feature of this unit is a selectable 15mA test available, to test fault loop
impedance without tripping any RCD installed upstream.
Innovative Automatic RCD Test Function

Simply by connecting to the circuit in auto mode and waiting at the
distribution boardto reset the RCD the HT2018 will perform six tests
checking the RCDs performance curve across , 1x and 5x its rating
at 0 and 180. Measured results are stored and also evaluated at pass/fail
against the standards.
Instruction manual, factory calibration certificate and test leads.
HTE-LINK downloading software c/w interface cable.
Catalogue No. HT 2018
Specifications
See RCD & Loop Impedance functions in the HT2019 specification table page 29..

25
www.nesco.com.au
AEMC Digital Earth Resistance Tester

Measures Earth Resistance 0.01 to 1999
Test current of up to 10mA
2 or 3 terminal measurement
4 terminal measurement soil resistivity
Auto-ranging selects the optimum range
Backlit display
Power supply Model 4620 8 x C batteries
Power supply Model 4630 AC powered and rechargeable NiMH batteries
Rugged dust and rainproof case
Instruction manual
Catalogue No. 4620
Earth resistance and earth resistivity test kits - refer Nesco for details.
SEW Digital Earth Resistance Tester

Test current of 2mA
Manual ranging 20,200,2000 scales
Power supply 8 x AA batteries
Red, Yellow , Green test leads, auxiliary earth spikes,
measurement probe, instruction manual
Catalogue No. 4120 ER
HT ITALIA GEOTEST Earth Resistance Tester

Test current up to 10mA
4 terminal measurement soil resistivity
Stores results
Carry case, instruction manual,
calibration certificate, 4 rods, 4 cables
EUROLINK 2000 downloading software and interface cable
Catalogue No. HT2016

26
HT ITALIA Power Quality Analysers
The HT ITALIA range of Power Quality Analysers are designed to test, measure, record and analyse single / three
phase systems (with or without neutral).
The instruments will display in real time the values of all fundamental electrical quantities and the trend waveforms
of voltages and currents. Software provided with these units enlarges the potentialities of the instruments.
From simply recording maximum demands of installations and equipment to recording voltage anomalies every
10ms HT ITALIA can accommodate these requirements in their range.
Simple to use, selection of type of measurement is made by rotating a switch and pressing selection keys.
HT2020E
ENERGY TESTER designed to carry out a complete analysis of the power supply.
HT9032
Power Quality Analyser incorporates the same features as the HT2020E combined with powerful tools for
investigating anomalies and disturbance.
GSC57
Total integration of a unique range of functions in one test unit.
Incorporating the features of the HT9032 with advanced Installation Test Functions and with the addition
of accessories Environmental Testing.
Specifications
Function HT2020E HT9032 GSC57
Voltages
Currents
Phase and Total Active Power
Phase and Total Reactive Power
Phase and Total Apparent Power Catalogue No.HT2020E
Phase and Total Power Factor
Frequency
Harmonics (from the 2nd to the 49th
for Voltage and Current)
Analysis of Voltage Anomalies
Harmonic Analysis
Phase Rotation
Leakage Current to Earth
Earth Resistance & Ground Resistivity
Catalogue No.HT9032
Insulation Resistance
Continuity (Test current up to 10A)
RCD Tripping Time & Current
Line & Loop Impedance
Calculation of Prospective Short
Circuit Current
Environmental Testing (with
accessories temperature,
humidity, air speed, luminosity) Catalogue No.GSC57
27
www.nesco.com.au
Meters & Accessories Te st In st r u m en t s
Installation Tester
Installation Testing is the overall term for the complete The HT2019 Combitestt distributed by NESCO Electrical
range of electrical tests which should be carried out Products provides an economical alternative to a range
on all new electrical installations and also on of separate pieces of test equipment providing the
existing installations which have had additions entire gamut of tests in a single, handheld instrument.
or alterations carried out. Low Resistance testing with >200mA test current,
insulation resistance tests (with test voltages from 50V
Most electrical workers are more than familiar with up to 1000V), multi-function RCD Testing, high current
the most common tests routinely carried out such as; Loop Impedance tests, and <15mA Loop Impedance tests
Insulation Testing & Low Resistance (Continuity), ) apart plus Phase Rotation make the HT2019 the answer.
from these there are also several other tests which are
now part of almost every electricians list of must do Not only does the HT2019 provide a complete testing
tests before signing off a job, Fault Loop Impedance, package but all results may be saved to an internal
RCD Test and on 3 Phase installations, Phase Rotation. memory and can then be transferred to a PC with an
optional download pack which includes software to
The adoption of new standards has made the enable fast and professional presentation of test reports
previously little known Fault Loop Impedance test a for customers. This also removes any doubts about the
virtual prerequisite (even though AS3000 does not call final results, which may be raised when using a manual,
this a mandatory test) and RCD Testing is equally as hand written system as the results are directly
important with these devices being commonplace. transferred from the tester to PC.
With the advent of such new requirements, many

electrical workers and companies have had to
re-assess their test equipment as they either had to
purchase several new testers or look at the alternative
of a single multi-function tester to do everything
required which is where the concept of the
Installation Tester was generated.
ContinuityTest Insulation Resistance
RCD AC Type
RCD Type A
Fault Loop Impedance
15mA Fault Loop

Impedance Feature
Phase Rotation
RS232 Output
Catalogue No. HT2019

28
HT ITALIA COMBITEST Multifunction Instrument
Measurement of Low Resistance, Insulation Resistan
Line and Fault Loop Impedance measurement with
Current calculation and Phase Sequence.
You can store the test results inside instrument m

instrument display and transfer them to a serial p
management software you will be able to create
3-pin plug lead, instruction manual, factory ca
and test leads, test probe and carry bag.
Catalogue No. HT-Link management softwa
Specifications
Voltage
Insulation Resistance (Test Voltages
Continuity (Test current 200mA) M
Frequency Hz
Line Impedance (phase phase, phase neu 01
20 199. 0.1
Fault Loop Impedance (phase - earth) 0.01 19.99 0.01
20 199.9 0.1
200 1999 1
Fault Loop Impedance (15mA test current, without RCD tripping) 1 1999 1
RCD Tripping Time (Type AC)
Rated Current 0 999ms 1ms
2 x Rated current 0 200ms 1ms
5 x Rated current 0 160ms 1ms
RCD Tripping Current (Type AC) 0.1mA
Phase Sequence Indication

29
www.nesco.com.au
SEW Fused Low Voltage Test Lamps

Low voltage test lamps are the simplest and most reliable instruments
for low voltage mains testing and proving for dead.
Lamps, carry case, instruction manual, fused lead, screw on alligator clip
Specifications
ACV 240/415V
Lamps 2 x 15W 220V
Fuse 0.5A / 660V
Catalogue No.STL-5
SEW Phase/Motor Rotation Tester

Checks open phase via lamps
Checks phase rotation via lamps
Checks motor rotation via lamps
Motor rotation can be determined on a de-energised

motor by connecting the test leads, hand turning the
rotor shaft and pressing the test button.
Carry case, instruction manual, test leads, 1 x 9V battery
(for motor rotation function)
Catalogue No. ST-860
SEW Phase Rotation Meter

Checks phase rotation via rotating disc
Lamps indicate weather a phase is open and which
phase at a glance.
Robust construction, sealed against dust.
Safety design, no exposed metal parts.
Carry case, instruction manual, test leads
Catalogue No. ST-855PR
30
TECPEL Digital Lightmeter
Simple one hand operation
Range from 20 to 200,000 Lux
Resolution 0.01Lux
Backlit display
Max/ Data hold function
Instruction manual, carry case, 4 x AAA batteries Catalogue No. DLM-530
Electromate Non Contact Infra Red Thermometer With Laser Pointer

Check for hot joints in electrical installations, moving
objects or where actual contact is not practical or desirable.
In-built laser sighting

Selectable C / F measurement
Automatic data hold and auto power off
Backlit LCD
Specifications
Temperature range 20C to 450C (-4F to 842F)
Power supply 9 volt battery
Included Accessories Catalogue No. DT-8811

Blister packaged
Ireland Mini Thermometers

Temperature range 50C to +250C
Resolution 0.1C / 1C
Data hold
LCD display
Catalogue No. 6201 Needle Point Catalogue No. 6202 Surface Probe

31
www.nesco.com.au
TECPEL Dual Input Temperature Meter

0.1 C or 1.0 C resolution selectable
Dual thermocouple input
Differential temperature measurement
Maximum and reading hold function
Measurement range 50 to 1300C (-58 to 2000F)
Sensor K-type thermocouple
Instruction manual, holster, 2 x TPK-01 bead probes, 1 x 9V battery
Refer to accessories page 38 for optional temperature probes.
Catalogue No. DTM-307
Martindale Microwave Leakage Detector

Microwave leakage detector with an audible warning device
and visual LEDs for detecting exposure levels.
The unit is supplied in an outer case, which contains a beaker and

a thermometer. This allows measurement of the microwave power
output by measuring the temperature rise in a known volume of
water after a fixed period of time.
Specifications
Power supply 9V battery
Self test function
Indicators
Green LED battery O.K.
Yellow LED 1mW.cmsq
Red LED and audible tone microwave
leakage above safety levels
Hard carry case, instruction manual, thermometer,
beaker, and detector Catalogue No. TEK500
32
SEW High Voltage Proximity Detector
The tester works by proximity; it senses that radiated field which
surrounds live conductors.
Visual and audible alert
Eight voltage detection settings -
240/2k/3.3k/6k/11k/22k/33k/66k/132k/275kV AC
Complete with sunrise fitting for hot sticks Catalogue No. 270HP
High impact plastic casing
Battery supply 3 x D batteries
Continuous self test function
Low battery indication
Also available Catalogue No. 270HP-SB (tester complete with 1.2 metre safety stick and carry bag)
MEET Non Contact Audible/ Visual Voltage Tester

Self test function
Non-contact volt tester 70-600V AC
Continuity tester 0 2M
DC polarity tester 1.5 -36V DC
Microwave leakage detection >5MW/cm
Included Accessories Catalogue No. MS-148E

Blister packaged, 2 x LR44 batteries
MEET Non Contact Test Pencil

Convenient easy to use test pencil

Contact volt tester 70 600V AC
Continuity tester 0 50 M
DC polarity tester 1.5 -36V DC
Microwave leakage detection >5MW/cm sq
IP 44 rated Catalogue No. MS-18
2 x 1.5V LR41 batteries
MEET Non Contact Audible/ Visual/Vibrating Voltage Tester

Unique tester is easy to hear with a cricket chirp audible alert
for the presence of voltage as well as vibration and visual indication.

Microwave leakage detection >5MW/cm
Included Accessories Catalogue No.MS-47VH
Blister packaged, 4 x LR44 batteries
MEET Non Contact Adjustable Sensitivity

Wide range of voltage detection
Self test function
4 x LR44 batteries
Catalogue No.MS-47NS-3
33
www.nesco.com.au
SEW Tone Tracer Kit

Designed for use mainly on data / communication systems
Identify and trace wires or cables in a group
Volume / sensitivity control
Continuity and polarity tester
Three colour LED display
Amplifier probe
Is designed to identify and trace wires within a group
without damaging the insulation.
Catalogue No. 180CB
Tone generator
Provides a tone and also serves as a continuity and polarity tester.
As well as tone a three-coloured LED displays results.
Instruction manual, alligator clip test leads, RJ11 test plug,
2 x 9V batteries, carry case.
C-Scope Underground Cable Locator / Tracer with Depth Indicator

High performance cable avoidance tool providing the ultimate information
about underground services before you dig.
Depth mode function displays the depth of the applied signal
when using the signal generator.
Fingertip controls, lightweight and rugged locator
Soft carry bag, detector, signal generator, instruction manual
Specifications
Detector
LCD display shows signal strength, battery condition, and signal depth
Speaker for audible detection
Power supply 8 x AAA batteries
Moisture and dust resistant IP65
Signal Generator Catalogue No. CS CAT-XD

Pulse / continuous switch
Power supply 4 x D batteries
34
C ab le Lo cati on &
Tr ad in g Eq u ipment
Martindale Elite Fuse Finder Kit

For tracing 240V circuits only
Transmitter, receiver, hard carry case, TL-83 test leads, 3-pin test lead
Specifications
Transmitter
Power supply from mains
Automatic and manual modes of detection for faster identification
Earth leakage from transmitter is nil
Receiver
Sensitivity adjustment via potentiometer
Response Audible and visual 6 segment bar graph
9V battery supply
Catalogue No. FD650
Pathfinder Circuit Tracer

Locate, trace and isolate circuits quickly and easily.
No distance limitation, track the circuit upstream from the transmitter.
Traces live or de-energised circuits (using an external power supply e.g. battery)
Operates on a wide range of voltages.
Transmitter, detector, carry bag, 3 pin test lead, 9V battery supply (for detector).
Specifications
Transmitter
Operating Voltage 9-600V AC/DC
Fuse protected
Detector
Sensitivity settings 2,10,20,100%
Detector response Visual 10 red LEDs
Audible chirp
9V battery power supply

Catalogue No. PF620
35
www.nesco.com.au
W i r ing Te s ter s Te st In st r u m en t s
AEMC Cable Length Meter & Fault Locator Alphanumeric TDR

Fault Mapper CA7024 measures the length of electrical and communication
cables up to 2000m.
Indicates the distance to a fault up to 2000m in the cable (open or short)

given access to only one end of a two or more conductor cable.
Built in tone generator for tracing and locating cables (optional Tone
Receiver Model TRO2 is required for detection).
Soft carry case, BNC pigtail cable with alligator clips, user manual,
4 x AA batteries.
Catalogue No. CA7024
Tone Receiver TRO2
AEMC Telephone/ Coaxial/ Parallel Cable Tester Graphical TDR

Fault Mapper Pro Model CA7026 identifies and locates faults and the distance
to them on power & communication cables up to 3500m given access to one
end of a two or more conductor cable.
Cable under test is displayed as an oscilloscope-like trace.
Built in tone generator for tracing and locating cables (optional Tone Receiver
Model TRO2 is required for detection).
Soft carry case, BCN pigtail cable with alligator clips, user manual,
4 x AA batteries. Catalogue No. CA7026
Tone Receiver Tro2
AEMC - LAN Cable Tester

Wire Mapper Pro Model CA7028 is a structured cable mapping and Catalogue No.TRO2
troubleshooting tester. It detects open circuits pairs, shorts, crossed wires,
crossed pairs, reversed pairs, split pairs and shield faults.
In the event of opens and shorts TDR technology is used to indicate if the
fault is at the near end or the remote end or if it is somewhere in between.
It will then indicate the distance to the fault up to 150m.
Service check function to detect telephone, 10BaseT, 100Mbit+ and token ring.
Cable length can be measured also the unit generates a tone into all
4 pairs under test that can be used for circuit tracing (optional Tone
Receiver Model TRO2 is required for detection).
Included Accessories Catalogue No. CA7028

Soft carry case, remote ID (#1), two patch cords, user manual,
4 x AA batteries.
Tone Receiver Tro2
Wire Mapper Pro Remote Ids (#2 to 5)
Wire Mapper Pro Remote Ids (#6 to 9)
Remote Unit
36
Electromate 1000V Fused Test Leads
Suits most multimeters
Short safety tips
500mA, 50kA fuses
Type A
1000V CATIII Catalogue No. 131301
Electromate 1000V Fused Test Leads

Suits most multimeters
Shuttered spike tips
500mA, 50kA fuses
Type A
Electromate Croc Clips To Suit 131301

or 131347 Fused Test Leads
One red, one black
Type A
Electromate Test Lead Set Suits

Catalogue No. TL-30
1826NA / 1813EL Meters
Electromate Generic Multimeter Leads

Suits most multimeters Catalogue No. TL-3A
Blister packed

SK-3015/ 1800IN Catalogue No. TL-5

1800IN, 1851IN, DMM etc. Catalogue No. TL-6
SANWA Test Lead Set Suits

Catalogue No. TL-82
RD700 & PC500/510/5000
Electromate 3 Pin Test Lead Set Suits

1826NA, 1813EL
Catalogue No. TL-EL
37
www.nesco.com.au
Test Leads, Carry

Cases & Accessories Te st In st r u m en t s
Electromate Vinyl Carry Case

Soft padded protection for most multimeters Catalogue No. CC1
Earth Wire Reel

Portable cable reel
Supplied with 2 alligator clips and earth spike Catalogue No. EWR-50F
Complete with 50 meters of flexible 1.5mm2 30/0.25 V90 trailing lead
CTWR
ALVEY Circuit Test Wire Reel
Handy test wire reel fitted with a large stud for meter test lead
connection (no cable or clip supplied)
Catalogue No. CTWR
NESCO Temperature Adaptor for DMM

Suits K type thermocouple Catalogue No. TA-100
Suits RD700, PC 510
NESCO Bead Temperature Probe Catalogue No. TP-01A

Type K 20 to 200C, air only
NESCO Sheath Temperature Probe

Type K 50 to 800C, pointed tip
Catalogue No. TPK-03S
NESCO Surface Temperature Probe

Type K 50 to 800C
Catalogue No. TPK-04
NESCO Air Temperature Probe

Catalogue No. TPK-05
Type K 50 to 800C
38
Wo r k p l a c e S af et y Pr o d u ct s
NESCO Rubber Safety Mats

Note: Other configurations in relation to size and voltage are available.
Please consult sales office for details. All rubber safety matting are
tested and tagged.
Part No Description
MATRUBBER Rubber Safety Floor Matting - Black
1000mm x 1000mm x 6mm thick
650 Volt AC
Tagged and Tested to AS2978-1995
C/W Protective Carry Bag
OHLMAT Overhead Linesmans Matting Yellow
1000mm long x 350mm drop
650 Volt AC
Tested to AS4202-1994
Catalogue No. MATRUBBER
ELECTROMATE Low Voltage Switchboard Rescue Kit

Features
Complies with Department of Mines and Energy specifications
Only high quality components used
High visibility container - bright yellow
Clearly labelled
Easy to store and transport
If used, the fire blanket and burns dressing must be replaced with
new items after a rescue has been effected.
All components are available as replacement parts.
Kit comprises of:

Part No Description
SBRBAG Rescue kit carry case
SBRT Weatherproof torch and batteries Catalogue No. SBRKIT
SBRFB Fire Blanket
SBRBD Multi trauma dressing
SBRSIGN Isolation tag
SBRCROOK 1000V rescue crook
RG1000360-11 1000V insulating gloves
All components available as separate items
Designed for the rescue of workers in live situations. Essential for all
personnel working in potentially dangerous locations. The type of
equipment you cant afford not to have, but hope you never need.

39
www.nesco.com.au
Wo r kp lace Saf et y Pr o d u ct s
NESCO Personal Protection Equipment Kit

A convenient kit to assist with safe work practices and hazards of a general nature.
Kit comprises of:

Carry Bag
1 x Pair reusable ear plugs
1 x First aid kit
1 x Lockout Tag Out of Service
1 x Pair safety glasses with lanyard
1 x Pair leather riggers gloves
1 x 4.25g SPF30+ lip balm applicator
1 x 500ml Hand cleaner
1 x Pair of ear muffs
1 x Sterile Burns treatment Dressing
1 x Lockout Tag Do Not Operate
1 x Voltage proximity tester
4 x Respiratory P1 Dust Masks
1 x 500ml pump action bottle of SPF30+ sunscreen
Catalogue No. PPEKIT
The PPE Kit provides some of the basic personal protective equipment that
can assist where hazards of a general nature may be present. Risk assessments
should be carried out to determine the level of risk and control measures and
or appropriate protective equipment required for each task. Also ensure that
the equipment provided is a proper and comfortable fit.
MOXHAM Roof Works Kit

Fall arrest kits designed for roof workers.
Part No Description
RWKIT Kit components can be selected to suit specific
applications
Please contact sales for further information
Catalogue No. RWKIT
40
NESCO Workplace First Aid Kits
Government Workplace Health & Safety Advisory Standard for First
Aid in the Workplace.
Contents of a First Aid Kit where the risk of injury or illness is MODERATE
Generally suitable for small construction sites, manufacturing and light

industry for 1 to 29 persons.
Catalogue No. SGFAKGPM
Metal Carry Case
Dimensions 380 x 130 x 165mm
Wall Mounted Version in a metal box Catalogue No. SGFAKGWM

NESCO Car & Travel First Aid Kits

Handy personal first Aid Kit basic items.
Catalogue No. SGFAKGB
Extension Lead Safety Clips

The OSC (Orange Safety Clip) is an Australian designed and manufactured
clip for holding extension leads up off the floor. It can be attached to
timer by nails or screws, metal by screws or by cable ties to other items.
Pack of 6
The SCC (scaffold cable carrier) is designed to support extension leads on

48mm scaffold pipe.
Catalogue No. OSC
Each clip will support 7 leads in three different sizes. 3 x 1.5mm,
3 x 1.0mm and 1 x 0.75mm. If someone accidentally snags the
cable, it will be released from the clip rather than dragging the
clip off its mounting.
Catalogue No. SCC

41
www.nesco.com.au
Harnesses
Part No Description
Harnesses
Elite Full Body harness with multiple attachement
points: ie rear buttock strap, extended dorsal,
side and front D-rings. Suitable for linesman,
riggers, tower workers & E.W.P work.
480S General Purpose harness, with adjustable leg and
sholder straps, dorsal D-ring, breathable triangular
back. Standard type harness for poletop work.
Can be worn comfortabley all day.
Pole Straps
136 Webbing pole strap and double action snap
hooks with 15mm opening and 90 degree twist
1.8 meter length.
148 As above complete with length adjustment,
by adjuster hook and toggle. 2.4meter length.
Lanyards
176WSA Two No 35 (15mm gap) hooks, 35mm webbing,
c/w shock absorber 1.8 meter length
176SA Two No 35 (15mm gap) hooks, 12mm rope,
c/w shock absorber 1.8 meter length
Catalogue No. Elite
Electrical Safety Sticker Kit

Convenient range of labels for switchboards and control cabinets.
Signs are manufactured from a durable, weather and chemical

resistant synthetic material, which is U.V. stable.
Kit includes
16 x DANGER 240 VOLTS (74mm x 105mm)
8 x DANGER 415 VOLTS (74mm x 105mm)
2 x DANGER HIGH VOLTAGE (148mm x 105mm)
2 x LIVE WIRES (148mm x 105mm)
1 x SWITCHROOM (104mm x 210mm)
1 x DANGER ELECTRICAL EQUIPMENT
Complete customisation of labels is available on request.

Catalogue No. ESAKIT
42
NESCO Safety Signs
4 convenient sizes to choose from see table below
Water, chemical & U.V. resistant
Prompt delivery
Choose from our standard range or customise your own.
Size Measurement
A 400mm x 280mm
B 195mm x 280mm
C 195mm x 135mm
D 135mm x 92.5mm
Note: To order quote A, B, C or D after the part number relevant to the sign
Many other styles available upon request

43
www.nesco.com.au
Safety Lockout Tags

Do not operate & out of service lockout tags are used to protect workers
from potential danger.
All tags are laminated.
Standard Dimensions are 140mm x 75mm
Standard styles are listed below (standard pack size is 5)
Customised Lockout tags which can include an ID photo are available upon request
Lockout/Tagout Video Training Program

Training Package for Employee Safety
10 minute video effectively conveys the importance of Lockout/Tagout
in the workplace
Demonstrates the 7 steps to properly apply, and 5 steps to re-energize
from, Lockout/Tagout
Provides instructions for maintaining Lockout/Tagout during shift changes
Shows how to apply, remove and maintain lockout devices
Also suitable for employee-refresher training sessions
Includes video, 10 Lockout/Tagout Procedure Employee Reference
Cards, instructors guide and employee quiz
Additional Employee Reference Cards also available (No.499PR)
Catalogue No. 499V

Master Lock Description
Model #
499V Complete Training Program w/video and 10 Employee
Reference Cards
499PR 10 Lockout/Tagout Procedure Employee Reference

Cards
44
Rotating Electrical Plug Lockouts
Outward/Inward Rotation Allows for Easier Application & Storage
Surrounds the electrical plug; protects against accidental reconnection
Unique, patent-pending rotating design allows for easier installation
in confined space applications
Each size roatates into istself to fit effectively into safety lockout application
Red lockout colour identifies the safety lockout application
Complete with high-visability permanent safety labels
Tough, lightweight, dielectric Xenoy thermoplastic bodies
withstand chemicals; perform effectively in extreme conditions
[temperature range -50F (-46C) to +350F (117C)]

Catalogue No. 487
Model #
487 2-1/4 dia. x 6x3-1/4 with cord dia. up to 3/4
488 3dia. x 6 with cord dia. up to 3/4
Catalogue No. 488
Pneumatic Lockout
Prevents Access to Compressed Air
Isolates equipment from compressed air sources
Device is applied to the male fitting, and accommodates most 1/4, 3/8 and
1/2 fittings

Model #
465 Pneumatic Lockout (1 ea.)
Catalogue No. 465

45
www.nesco.com.au
Lock Outs
Part No Description
Safety Lockout HASP
420 1 Diameter Jaws
421 1-1/2 Diameter Jaws
Circuit Breaker Lockouts

Catalogue No. 420 & 421
UCL-1 Miniture circuit breaker lockout
UCL-2 Moulded case circuit breaker lockout
UCL-2-EL Moulded Case, Earth Leakage Circuit, Breaker Lockout
UCL-5 Moulded case circuit breaker lockout
Fuse Holder Lockout
UFL-2 Fuse holder lockout

Catalogue No. UCL-1, UCL-2 & UCL-2-EL
Adjustable Cord Lockout
MFL-1 Multi funciton cable lockout device
Lockout Padlocks
LOPL Brass baodied lockout padlock 1-1/2 shackle clearance
Lightweight Safety Padlock
410 RED Keyed different (vertical shackle clearance 1-1/2)

Non-conductive Xenoy lock body 1-3/4 tall Catalogue No. UCL-5 & UFL-2
Customise on site with permanent write on lables
High security, reserved for safety cylinder - up to
1000,000 key changes
Key retaining - ensures that padlocks are not left
unlocked
411 RED Keyed different (vertical shackle clearance 1-1/2)

Non- conductive Xenoy lock body 3 tall
Customise on site with permanent write on labels
High security, reserved for safety cylinder - up to
100,000 key changes
Key retaining - ensures that padlocks are not left Catalogue No. MFL-1
unlocked.
Steel Body Padlock
3LF RED Keyed different (vertical shackle clearance 1-1/2)

Reinforced laminated steel construction
1,400 key changes
Catalogue No. LOPL
Catalogue No.410 & 411 Catalogue No. 3LF

Plastic Bodied Laminated Steel
46
Personal Lockout Kit
Carry bag
1 x UCL-2 Moulded case circuit breaker lockout
1 x MFL-1 Multi funciton lockout
1 x padlock
1 x lockout hasp
Voltage proximity test screwdriver
2 x UCL-1 Miniture circuit breaker lockouts
Danger tags
Cable ties
Marking pen
Catalogue No. LOK
Rotating Gate Valve Lockouts

Outward/Inward Roataion Allows for Easier Installation & Storage
Surrounds the valve operating handle to protect against
accidental valve opening
Unique, patent-pending rotating design allows for easier installation
in confined space applications
Each size rotates into itself to fit efcectively into safety tool boxes
Each size nests within the next larger size to save space in storage
Up to 4 workers can apply their personal safety locks
Red lock colour identifies the safety lockout application
Complete with high-visibility permanent safety labels that can be
written-on to identify the responsible person, then erased for the next job
Tough, lightweight, dielectric Xenoy* thermoplastic bodies withstand
chemicals; perform effectively in extreme conditions [temperature
range -50F (-46C) to +350F (177C)
Catalogue No. 481

Master Lock Measurement
Model #
480 fits 1 to 3 dia. valve handles
482 fits 4 to 6.5 dia. valve handles
485 1 set of Nos. 480-484 Catalogue No. 485
* Xenoy is a registered trademark of General Electric Corporation.
47
www.nesco.com.au
Ball Valve Lockouts

Fit All Major Brand Ball Valve Handles & Applications
Single-piece design is easy to apply and assures the best fit every time
Forms a triangular wedge to the pipe so that the handle cant be turned open**
Two sizes fit the majority of applications
Master Lock Measurement For Valve

Model # Diameters of:
476 Tough Nylon Ball Valve Lockout Device 1/4 to 1
477 Heavy Steel Ball Valve Lockout Device 1-1/4 to 3 Catalogue No.476
Catalogue No.477
Universal Ball Valve Lockout Device

Locks Out Almost Any Quarter Turn Valve
Designed to lock out virtually any size and shape ball valve
Device clamps over valve handle; lockout arm ratchets to abut and lock
against pipe at any angle**
Accommodates both standard and odd-shaped handles up to 1-1/4 thick
and 1-5/8 wide
Add on the separate lockout arm (No. 479) to lock handles in throttled
position and to lock out 3-, 4- and 5-way valves
Master Lock Measurement For Valve Catalogue No.478 & 479

Model # Diameters of:
478 Universal Ball Valve Lockout Device 1-1/4 thick x
1-5/8 wide
479 Adaptor Arm for 3-, 4- and 5-way valves 1-1/4 thick x
1-5/8 wide
** When properly applied. Complete the lockout with a Master Lock safety padlock.
48
Circuit Breaker Switch Padlock
Provides the flexibility to effectively lock out breaker switches
Flexible steel cable shackle allows padlock to properly lock all types of
circuit breaker lockout devices
Flexi-cable allows the lock body to be moved out of the way, and panel
door to be closed properly
Fits the tight space constraints within circuit breaker shutoff boxes
Numerous key changes are available to minimize the possibility of
unwanted key duplication
Master Lock Model # Description

7C5RED 1-1/8 wide steel body; 4-pin cylinder;
5 flexible steel cable
Catalogue No. 7C5RED
Group Lock Box

Captured key storage device, for effective lockout of large equipment
Effective alternative to requiring each authorized lockout team member to

place one of their personal safety locks at every lockout point in the system
The Group Lock Box allows for each lockout point to be secured with just
one designated lock. The accompanying keys are then captured by placing
them in the Group Lock Box. Each authorized employee locks just one
personal safety lock onto the box. the captured keys cannot be removed,
nor the equipment re-energized, until all workers have removed their locks
from the box.
Up to 13 workers can apply their personal safety locks
Heavy duty steel construction
Red lockout colour identifies the safety lockout application
Catalogue No. 498A
Trilingual label clearly communicates to all workers
Master Lock Model # Description Length Width

498A 6 9-1/4 3-3/4
Accessories for Low Voltage Insulating Gloves

Accessories
Part Number Description
EOVC-9 Cowhide Overglove size 9
EOVC-10 Cowhide Overglove size 10 Catalogue No. EOVC
EOVC-11 Cowhide Overglove size 11
EOLK Cotton knitted liner
EOLS Seamless liner
EOBS Single Compartment Canvas Bag
EOBT Triple Compartment Canvas Bag
Catalogue No. EOBS

49
www.nesco.com.au
Low Voltage Insulating Gloves

The range of rubber gloves provides electrical workers with superior electrical protection and maximum comfort.
Specifications
Composition: Natural rubber specifically formulated to ensure high dielectric properties.
Glove Markings: Each glove is marked with the following

1. Name of manufacturer
2. Year & month of manufacture
3. Working potential
4. Size
5. Batch number
6. IEC 903Class & Type or AS2225 Standards Mark and License No 901
Australian Standard AS-2225

RG00650360-9 650 Volt Working 5000 Volt tested 360 long insulating glove size 9
RG1000360-10 1000 Volt Working 10000 Volt tested 360 long insulating glove size10
RG3300360-11 3300 Volt Working 15000 Volt tested 360 long insulating glove size 11 Note: All gloves are
batch tested at the
time of manufacture to
RG4000360-10 4000 Volt Working 20000 Volt tested 360 long insulating glove size 10 either AS2225 or IEC903.
International Standard IEC903

Insulating Glove Accessories - See page 49

50
A u t o m a t i o n Pr o d u ct s Remote Control
Remote Control Typical Applications
General Description
The Nesco and Electromate remote control product ranges are basic
wireless switching systems used to operate almost anything.
Lights, gates, security systems, pumps, in fact any device that can be
switched on or off through an electrical circuit can be switched remotely.
Through walls, across paddocks, over car parks, use it where running a
switch wire is impractical or impossible.
With over one million units sold world wide, these systems are well
proven, economical and reliable.
System Requirements Security Monitoring

All systems comprise of two main components, a transmitter (Tx), which
transmits a coded radio signal, and a receiver (Rx), which receives the
coded signal and switches an output. The output is usually a relay that
becomes the actual switch in the circuit.
Most transmitters are battery powered, hand held units with 1, 2, 4 or 8

pushbuttons while the receivers are hard wired and permanently mounted
printed circuit cards and generally located in close proximity to the load
being switched.
Also available are a range of accessories such as antenna, low voltage

power supplies, enclosures and mounting bases.
The most basic system must consist of at least one transmitter and one
receiver. The actual components selected will be determined by the
Pump Control
application. Always consult with a Nesco sales consultant if in doubt with
your selected application.
Application Notes
All distances are quoted as line of sight. Although these units will operate
out of sight of each other, they are more effective and reliable when in
visual contact. Receivers must not be mounted near equipment that emits
radio interference, machinery such as variable frequency controllers, DC
motors and controllers, transformers, magnets etc. When using in an
industrial application, always chose a clean circuit to wire the receiver
into. Do not leave transmitters near equipment containing induction coils
such as stereo speakers as this will de-tune the transmitter.
Never use this type of remote control switching device on life endangering
equipment such as overhead cranes, hoists and conveyor belts. There is Industrial Monitoring & Control
specialist equipment designed for these applications.
Garden Lighting
51
www.nesco.com.au
Remote Control A u t o m at io n Pr o d u ct s
NESCO FM Series
First generation remote equipment. Operates on 27MHz with a 12 way
digital decoding footprint. Coding system is user-operated dipswitches on
both the transmitter and receiver. To enable a transmitter to talk to a
receiver the dipswitches in the transmitter must be in identical positions
to the dip switches on the receiver. At least one third of the dipswitches
should be in the on position.
A 27MHz antenna is generally required for successful switching, however FMT PET
in ideal conditions or over short distances a piece of building wire 500mm
long may be sufficient. Maximum transmission time of all fixed
transmitters is 5 minutes.
Transmitters
FMT 302
Specifications
FMT PET Single Channel

6 volt battery powered (included)
Built in antenna & push button 100m range* FMT 301
FMT 301 One, Two or Four Channel
FMT 302 9 volt battery Powered (included)
FMT 304 Built in antenna & push button 200m range*
FMT 312E Single Channel

12 volt DC power required
Switching device required FMT 304
Antenna required
3km operating distance*
Programmable output (requires some user programming) FMT 312E
* Maximum distance in ideal conditions
Receivers
Specifications
FMR 212T Available for 11 to 28v AC/DC power supply

Single channel, *5 amp 240volt relay output non continuous
FMR202 11 to 28V AC/DC power required

2 channels, *5 amp 240volt relay output, non continuous
FMR 204 Available for 12 or 24v AC/DC power supply

4 channels, *5amp 240-volt relay output, non continuous
FMR 240 240 volt AC power required

1 channel, 10 amp 240 volt relay output
All receivers supplied as cards only
*A slave relay must be used when controlling (loads) rated at 240V.
52
NESCO Gigalink Series
The Gigalink is the second-generation remote control, offering more
power, smaller units and increased options. Although the increase in
power will not increase the operating distance, it will make the system
more reliable in poor reception areas. The transmitters are physically
smaller and designed for easy use. The receivers offer more user
programmable options.
Transmitters GLT-2701 GLT-2702
Single & multi channel available

LED indication of operation
9 Volt battery powered
Standard 27.195MHz frequency, others available on request
Built in antenna
Over 4 billion security combinations
Operating distance up to 150 metres nominal
GLT-2704
Specifications
GLT-2701 Single channel
GLT-2708
GLT-2702 Two channel
GLT-2704 Four channel
GLT-2708 Eight channel
GLT-2712E Single channel
12V DC power required
Switching device and antenna required
3km operating distance
GLT-2712E
Receivers
Specifications
GLR 2701 1028 Volt AC/DC power required
Single channel, *5amp 240-volt relay output non continuous
Programmable output modes
GLR 2702 10-28 Volt AC/DC power required
Two channels, *5 amp 240-volt relay output non continuous
GLR 2704 12 or 24 Volt AC/DC power supply required
4 channels, *5 amp 240volt relay output non continuous
GLR 240 240-Volt AC power supply required
One channel, 10-amp 240-volt relay output
GLR 2708R 12 or 24 Volt AC/DC power required
8 channel, *5 amp 240 volt relay output non continuous
All Gigalink receivers supplied as cards only
*A slave relay must be used when controlling loads rated at 240V.

53
www.nesco.com.au
Remote Control A u t o m at io n Pr o d u ct s
Gigalink Output Modes

The output modes on the Gigalink range of remote controls are user
selectable. The GLR 2701 and GLR 240 have seven different modes to
select from. A series of 4 dipswitches in the centre of the card allow
the user to select from momentary, latching, delayed off, pulsing and
flip flop modes.
The GLR 2702 and GLR 2704 have two dipswitches allowing the user
to select momentary, latching or flip flop modes for all channels.
Full instructions on programming are included with every Gigalink

receiver purchased.
Accessories
Catalogue No. C160
Specifications
Part Number Description Catalogue No. QM150
C 160 This enclosure is the perfect size to install any of the

Enclosure receiver cards except the GLR2708 Series.The lid is
hinged for easy use, and a rubber insert around the
door makes it weatherproof.
QM 150 This item makes mounting a receiver card in the C160
Quickmount enclosure a breeze. Simply screw the quickmount in
the enclosure and the receiver card clips into it. No
need to mess around with stand off studs.
A full range of accessories are available for the Nesco and Gigalink
remote controls
Antenna
Specifications
ANT 27S 30cm Long, supplied with mounting socket, requires
a ground plane.
ANT 27M 1.2m Long, supplied with 2m of coax and a universal
mounting base. Does not require a ground plane
ANT 27L 2m Long, marine grade antenna supplied with 2m of
coax and universal mounting base. Does not require
a ground plane
Mounting the antenna for maximum reception is important, follow the
diagrams for recommended mounting positions.
Catalogue No. ANT-27M
Antenna Installation
Very poor Poor OK Good
54
Remote Control Systems
NESCO manufactures and assembles customised REMOTE CONTROL SYSTEMS
for special applications.
Gigalink Kit
This kit contains a GLT2701 transmitter c/w 9V battery and GLR240 receiver
mounted in a C160 IP55 P.V.C. enclosure. It has an operating distance line of site
up to 50 meters without a fixed antenna and up to 150 meters with an antenna.
The kit has been designed for rapid and easy installation and useful for a variety
of applications such as operating pool pumps, outside lighting, warning sirens
and bells. Catalogue No. GLRK-240
School Bell System

This system uses a fixed transmitter and receiver mounted in two IP55 P.V.C. enclosures supplied with two antennas. The
transmitter can be wired to the existing school bell control circuit with any number of receivers installed in remote
buildings coded to and controlled by the single transmitter. Providing a low cost alternative to conventional wiring.
Although designed for the operation of school bells the same kit can be used to switch any electrical components
up to a 3km.
240Vac
Antenna
Connection
Block
A
240V
Antenna N
N/C To your
FMR240 control
FMT312E Antenna 10A/240V N/O
PSU1202 circuit
Transmitter
Regulator Shield Switching
12Vdc voltage
C
Cable and Connections by others
A N
+ -
Earth
Cable and Connections by others
Advance Control System

Some applications require modifications to our standard transmitters and receivers to allow for extra features.
Such as multi channel, high-low, stadium floodlight control etc.
Contact NESCO for assistance with special applications.
55
www.nesco.com.au
Fl o a t S w itc h e s A u t o m at io n Pr o d u ct s
ATMI Float Switches

Float switches are designed to control fluid level by switching a set of
contacts when the level either rises or falls. Each individual application
will determine the model of float switch required.
To simplify the application criteria, Nesco has reduced the possibilities

to only two models.
The AT 920 series is designed for applications like sump pumps, water storage
tanks and clean dams. They do not operate effecively in fluids which are fast
flowing, turbulent, or have large amounts of suspended solids.
The MR 76 series is designed for industrial applications. It can be used in

fluids containing a large percentage of suspended solids. They are also very
good in acidic or alkaline situations such as sewerage or industrial waste.
All float switches supplied by Nesco Conwell have a double throw

mechanism. This means they can be used for either filling or emptying
purposes. Both models are available in 5, 10 and 20 metre cable lengths.
AT 920VR* Ball Float

Specifications
Suitable for water with limited suspended solids
Suitable for fluids with limited turbulence
Suitable for drinking water, sump pumps
No lead or mercury
Biconical shape
Uses limit switch operated by a ball race
Switch rating 20A resistive 250V
8A Inductive 250V
Maximum operating temperature 85C
Dimensions 135mm x 7mm
*insert cable length 5, 10 or 20
Catalogue No. 920VR

MR 76VR*
Specifications
Industrial quality
Suitable for turbulent fluids
Suitable for acidic liquids (sewerage)
Suitable for liquids with a high level of suspended solids
Mercury switch for accuracy
Bi-conical shape to prevent solids from sticking
5 water proof compartments
(will still operate with 2 compartments damaged)
Switch rating 10A resistive 250V
5A Inductive 250V
Maximum operating temperature 70C
Dimensions 170mm x 80mm
* insert cable length 5, 10 or 20
Catalogue No. MR 76VR
56
Timers
ANLY Multi Range Timer

AH5N
Features
1 second to 600 hours time range
Programmable by dip switches
24/240V AC/DC operating voltage
One timed and one user selectable set of contacts
Supplied with Base
Surface mounting kit available [Y50]
Specifications
Name Description
Full time range 1s,10s,1m, 10m, 1h, 10h, 60h, 600h
Rated voltage 24 to 240 volts AC/DC
Contact rating 5 Amps AC resistive
Reset time 0.2 seconds
Power consumed 2VA
Mounting base PF083A
Surface mounting kit Y50 & P3G-08
Size 48mm x 48mm x 84mm

Catalogue No. AH5N
AH3-RA
Features
Multiple time ranges programmable by dip switches
Time ranges from 1 second to 10 minutes
Supplied with Base
Specifications
Name Description
Full time range 1s,10s,1m, 10m
Power consumed 2VA
Mounting base PFO83A
Size 58mm x 40mm x 57.5mm

Catalogue No. AH3-RA
57
www.nesco.com.au
Timers A u t o m at io n Pr o d u ct s
ANLY Multi Range Timer

AH3-RC
Features
Time ranges from 6 seconds to 60 minutes
Supplied with Base
Specifications
Name Description
Full time range 6s, 60s, 6m, 60m
Power consumed 2VA
Size 58mm x 40mm x 57.5mm

Catalogue No. AH3-RC
AH3-RE
Features
Time ranges from 3 minutes to 30 hours
Supplied with Base
Specifications
Name Description
Full time range 3m, 30m, 3h, 30h
Power consumed 2VA
Size 58mm x 40mm x 57.5mm Catalogue No. AH3-RE
58
Off Delay Timer AH5F
Features
True off delay timer
Times out after power is removed
One set of change over contacts
Specifications
Name Description
Rated Voltage 240 Volts AC
Time Range 60 seconds or 30 minutes
Contact 1 change over
Contact rating 5 amps
Size 48mm X 48mm X 84mm
Catalogue No. AH5F
Base PF085A
Star Delta Transition Timer TRD-N

Features
Adjustable run time up to 30 seconds
Star to delta change time 0.1 second
Available in either 240 or 415V AC
Two indicating lamps for timer status
Specifications
Name Description
Time range 0-30 seconds
Rated voltage 240 to 415 volts AC
Contact rating 5 Amps resistive
Change over time 0.1 seconds
Base 8PFA
Size 61mm x 49mm x 70mm Catalogue No. TRD-N
Floatless Level Controller AFR-1

Features
For use where float switches are impractical
Suitable for filling and emptying
Uses 8 volts AC through probes
APS-3 probe holder available
Specifications
Name Description
Rated voltage 240 volts AC
Operating voltage 8 volts AC
Operating resistance 4K
Response time 80 milli-seconds max
Contact rating 5 amps resistive
Base 8PFA
Size 61mm x 49mm x 70mm Catalogue No. AFR-1
59
www.nesco.com.au
ANLY Twin Timer

ATDV-NA
Features
Asymmetrical cyclic timing
Time ranges from 1 second to 10 minutes
110 & 240 Volt AC operation
On & off times independently adjustable
ATDV-NC
Features
Time ranges from 6 seconds to 60 minutes
Catalogue No. ATDV-NA
ATDV-NE
Features
Time ranges from 3 minutes to 30 hours
Specifications
Name Description
ATDV
Full time range 1s,10s,1m, 10m
Rated voltage 110/240V AC
Power consumed 2VA
Mounting base 8PFA
Catalogue No. ATDV-NC
ATDV-NC
Full time range 6s, 60s, 6m, 60m
Power consumed 2VA
Mounting base 8PFA
ATDV-NE
Full time range 3m, 30m, 3h, 30h
Power consumed 2VA
Mounting base 8PFA Catalogue No. ATDV-NE
60
ANLY 3-Phase Sequence Voltage Relay ASM-170-415
Characteristic
Only operational with correct power source voltage and phase sequence.
Suitable for main power source and motor starter circuit to prevent
damage from insufficient phases or phase reversal.
3-Phase, 3-Wire or 1-Wire

11P
Red LED (ON), Green LED (POWER)
Specifications
Operating Voltage 415V AC
Allowable operating 85~110% of rated operating voltage
voltage range
Rated frequency 50/60 Hz
Contact rating 250VAC 5A resistive load
Reset time 300~600mS
Power Consumption Approx. 2VA
Life Mechanical: 5,000,000 times
Electrical: 100,000 times
Ambient temperature -10 ~ +50C
Ambient humidity Max 85% RH
Catalogue No. ASM-170-415
Base 11 Pin PF113A
Size 80.5 x 35 x 73.3
ANLY AC Line Voltage Relay AVR

Characteristic
3-Phase voltage and fault detector
Can dectect abnormal condition to prevent damages to the equipment
Auto shut-off while detecting excessive or insuffiecient voltage, range from
5% to 20% variable
Out-of-phase detection while the motor operating
Can be set up to detect excessive or insufficient voltage only
Delay and Reset time - 0~10sec adjustable tripping delay
Specifications
Operating Voltage AC(V) 415
Allowable operating 5% ~ 20% of rated operating voltage
voltage range
Detecting method detect from supply voltage
Reset time AVR 172: 0~10sec adjustable
Contact rating 250VAC 5A (resistive load)
Power consumption Approx. 3VA
Life Mechanical: 5,000,000 times Catalogue No. AVR 172-IIT
Electrical: 100,000 times
Ambient temperature -10 ~ +50C
Ambient humidity Max 85% RH
61
www.nesco.com.au
ANLY Multi-function Digital Timer H5CLR

Characteristic
Eleven field-selectable output modes accommodate a wide variety
of applications
7-segment-display for clear display and effective monitoring
All parameters set by scroll through menus accessed from the front panel
Field-selectable time ranges form 0.001 second to 9999 hours
Precision control possible to 0.001 second
Four levels of key protection provided
Available on Count Up or Count Down model
Specifications
Operating Voltage AC/DC(V): 12~48 or 100~240
Allowable operating 85~110% of rated operating voltage
voltage range
Contact rating 250VAC 5A (resistive load)
Reset time Max 0.1S
Catalogue No. H5CLR
ANLY PID Temperature Controller AT01

Features
Easy to use Panel lock protection function
PID funciton selectable Sensor malfunction detection function
Heating or cooling control selectable
Specifications
Model Sensor Input Control Output Dimensions
AT-501-PR Pt 100 Relay 5A 250VAC 48mm x 48mm
AT-701-PR Pt 100 Relay 5A 250VAC 72mm x 72mm
AT-501-KR K Thermocouple Relay 5A 250VAC 48mm x 48mm
AT-701-KR K Thermocouple Relay 5A 250VAC 72mm x 72mm
Specifications
Name Description
Alarm output 250VAC 5A
Control method PID, PI, P, ON/OFF
Catalogue No. AT-501
Setting Digital setting using front panel keys
Indicator 7 segment display and LED
Operating voltage AC(V): 90~260
Power consumption Approx. 3VA
Measuring accuracy Within 0.3% of present value or 2C
whichever is greater
Proportional band (P) Up to maximum allowable setting by sensor
input type
Integral time (I) 0~1999sec (1 second units)
Derivative time (D) 0~1999sec (1 second units)
Control period 0~65sec (1 second units)
Sampling period 250ms Catalogue No. AT-701
62
To g g le Switches
Mounting Bases
Accessories
8PFA 8 pin base Din rail or surface mounting hold Catalogue No. 8PFA & PF083A
down clips raised center section
PF083A 8 pin base Din rail or surface mounting raised
center section
PF085A 8 pin base Din rail or surface mounting
recessed center section
P3G-08 8 pin socket reverse pin for surface mounting
Catalogue No. PF085A & P3G-08
recessed center section
APS-3 Probe holder for use wih AFR-1 Holds 3
probes threaded to 6mm
Catalogue No. APS-3
ELECTROMATE Metal Toggle Switches

Specifications
Part No. Description Terminals Pin
ETS-101QC ON/OFF SPST QC Terminals 2
ETS-101SC ON/OFF SPST Screw Terminals 2
ETS-102QC ON/ON SPDT QC Terminals 3
ETS-102SC ON/ON SPDT Screw Terminals 6
ETS-103QC ON/OFF/ON SPDT QC Terminals 3
Catalogue No. ETS-1000
ETS-103SC ON/OFF/ON SPDT Screw Terminals 3
ETS-123QC MOM ON/OFF/MOM ON SPDT QC Terminals 3
ETS-123SC MOM ON/OFF/MOM ON SPDT Screw Terminals 3
ETS-111QC OFF/MOM ON SPST QC Terminals 3
ETS-111SC OFF/MOM ON SPST Screw Terminals 3
ETS-112QC OFF/MOM ON SPDT QC Terminals 3
ETS-112SC OFF/MOM ON SPDT Screw Terminals 3
ETS-201QC ON/OFF DPST QC Terminals 4
ETS-201SC ON/OFF DPST Screw Terminals 4
2-3 Pin
ETS-202QC ON/ON DPDT QC Terminals 6
ETS-202SC ON/ON DPDT Screw Terminals 6
ETS-203QC ON/OFF/ON DPDT QC Terminals 6
ETS-203SC ON/OFF/ON DPDT Screw Terminals 6
ETS-223QC MOM ON/OFF/MOM ON DPDT QC Terminals 6
ETS-223SC MOM ON/OFF/MOM ON DPDT Screw Terminals 6
ETS-212QC ON/MOM ON DPDT QC Terminals 6
ETS-212SC ON/MOM ON DPDT Screw Terminals 6
ETS-213QC MOM ON/OFF/ON DPDT QC Terminals 6
ETS-213SC MOM ON/OFF/ON DPDT Screw Terminals 6 4-6 Pin
63
www.nesco.com.au
Swi tc he s C o n t r o l Pr o d u ct s
ELECTROMATE ROCKER SWITCHES

RS and IRS
Specifications
Name Description
Rating AC 125V 20A; AC 250V 15A: DC 12V 20A
Contact R; 35M max
Insulation R; DC 500V 100M min
Dielectric Strength AC 1500V, 1 minute

RS-2101-1A
Operating temperature -30C 80C On-Off, 15 Amp 240V, DPST 4Pin
Electrical life 10,000 cycles
RS-101-1A RS-103-3B RS-2101-1C

On-Off, 15 Amp 240V, SPST 2Pin On-Off-On, 15 Amp 240V, SPST 3Pin On-Off, 15 Amp 240V, DPDT 4Pin
RS-101-1B RS-201-1A RS-2102-2C

On-Off, 15 Amp 240V, SPST 2Pin On-Off, 15 Amp 240V, DPST 4Pin On-On, 15 Amp 240V, DPDT 6Pin
RS-101-7C RS-201-2A IRS-1

On-Off, 6 Amp 240V, SPST 2Pin On-Off, 15 Amp 240V, DPST 4Pin On-Off, 10 Amp 240V, SPST 3Pin
RS-103-3A RS-203-1A IRS-1-2C

On-Off-On, 15 Amp 240V, SPDT 3Pin On-Off-On, 15 Amp 240V, DPDT 6Pin On-Off, 10 Amp 240V, SPST 3Pin
64
C o n t r ol Pr o d u ct s Switches
IRS-101-A IRS-201-1A
On-Off, 10 Amp 240V, SPST 3Pin On-Off, 15 Amp 240V, DPST 4Pin
IRS-101-1B IRS-201-2A
IRS-101-2B IRS-203-1A
On-Off, 15 Amp 240V, SPST 3Pin On-Off-On, 15 Amp 240V, DPDT 6Pin
IRS-101-3B IRS-2101-2C
IRS-101E-1C IRS-101E-1O
On-Off, 15 Amp 240V, SPST 3Pin On-Off, 10 Amp 240V, SPST 3Pin
65
www.nesco.com.au
Swi tc he s C o n t r o l Pr o d u ct s
MRS and MIRS

Specifications
Name Description MIRS-101-2
Rating AC125V 6A; AC 250V 3A On-Off, 6 Amp 240V, SPST 2Pin
AC125V 10A; AC 250V 6A (A)
Contact R; 35M max
Operating temperature -30C80C
MRS-101
On-Off, 6 Amp 240V, SPST 2Pin
MWS-01
MRS-201-3 MRS-101-2 MOM(On)-On, 10 Amp 240V,
On-Off, 6 Amp 240V, DPST 4Pin On-Off, 6 Amp 240V, SPST 2Pin SPDT 3Pin
PBS
Specifications
Name Description
Rating AC125V 3A; AC 250V 1A
Contact R; 20M max PBS-11A
On-Off, 1 Amp 240V
Electrical Life 50,000 cycles
EIL10R EIL10G EIL10A

Red in colour Green in colour Amber in colour
PBS-12A
Indicator lamp 4.8mm terminal 16AMP 240V On-Off, 1 Amp 240V
EIL12R EIL12G EIL12A

Red in colour Green in colour Amber in colour
Indicator lamp 6.3mm terminal 16AMP 240V
EFH01
Fuse holder 10AMP 240V 6 x 30mm
Specifications
6 x 30mm
20M (max)
DC500V100M
AC2000V/minute
66
VASS Common Plug-In Take Off Boxes
Single Phase
When ordering single phase take off boxes specify phase A, B or C.
Specifications
Rating Order Code
HRC Fuse
20A S1/20/HRC
32A S1/32/HRC
Catalogue No. SI/32/HRC
(HRC Fuse Links available if required)
Cord Clamp S/CC - To grip flexible cables. Fits all Take Off Boxes.
Circuit Breaker
10A S1/10/CB
16A S1/16/CB
20A S1/20/CB
25A S1/25/CB
32A S1/32/CB
Earth Leakage
10A S1/10/ELCB
16A S1/16/ELCB
20A S1/20/ELCB
25A S1/25/ELCB
Catalogue No. SI/20/CB
32A S1/32/ELCB
Fitted with Earth leakage Circuit Breaker
A C
N B
N (Neutral), A, B, or C Phases, E (Earth)
Catalogue No. SI/20/ELCB
67
www.nesco.com.au
C o n t r o l Pr o d u ct s
VASS Common Plug-In Take Off Boxes

Three Phase & Neutral (Black Rating Plate)
Specifications
Rating Order Code
HRC Fuse
20A S4/20/HRC
32A S4/32/HRC
63A S4/63/HRC
100A S4/100/HRC
200A S4/200/HRC
(HRC Fuse Links available if required)

200A HRC Fused Take Off or 200A Combination Fuse Switch (CFS)
Circuit Breaker
Catalogue No. S4/63/HRC
10A S4/10/CB
16A S4/16/CB
20A S4/20/CB
25A S4/25/CB
32A S4/32/CB
40A S4/40/CB
50A S4/50/CB
63A S4/63/CB
100A S4/100/CB
125A S4/125/CB
160A S4/160/CB
200A S4/200/CB
Earth Leakage Catalogue No. S4/20/CB

10A S4/10/ELCB
16A S4/16/ELCB
20A S4/20/ELCB
25A S4/25/ELCB
32A S4/32/ELCB
40A S4/40/ELCB
50A S4/50/ELCB
63A S4/63/ELCB
80A S4/80/ELCB
100A S4/100/ELCB
Fitted with Earth leakage Circuit Breaker
Catalogue No. S4/32/ELCB

68
CRITEC Surge Protection
The CRITEC range of surge protection products is widely recognised in Australia as providing a premium level of
protection. All the listed products are designed for use on the Australian 240V single phase or 415V three phase AC
power system, and provide both hard wired and point of use plug-in protection. They all feature excellent transient
clamping, and feature safe disconnection mechanisms at their end of life, with a visual indication given in this
circumstance.
Hard Wired Solutions

The hard wired protection products come packaged as convenient Din-rail mountable protectors, matching the style of
common circuit breakers. They are economically priced, and are available in three surge ratings: 10kA, 40kA, and 100kA
(8/20us surge impulse). The required surge rating for a particular application depends on where the protector is to be
installed. The 10kA protector should only be installed at sub-panels within a building. The 40kA protector is suitable for
point of entry installation for buildings in a relatively low lightning activity area or a low-lying building in a built up
area. It may also be used in a sub-panel for high lightning areas. Buildings in high lightning areas, or that are in exposed
locations, should have 100kA protectors installed at their point of entry main panels. Also, the higher the surge rating,
the longer the likely lifetime of the product, with the 100kA surge rating being a wise choice where long life is an
important consideration.
If the protectors are being installed in the panel where the Neutral to Earth link is, then one protector should be
provided from each phase conductor to neutral (i.e. one protector is required for single phase, and three protectors are
required for three phase). If they are being installed in a panel without the N-E link (e.g. a sub-panel), then an extra
protector should be provided from N-E.
With the exception of the high energy 100kA product, the protectors feature replaceable modules. This allows a failed
protector to be replaced without disturbing the wiring. In addition, the DSD1401SR275 product features alarm contacts.
These provide a changeover contact set, that allows remote monitoring of the protector status.
Specifications
Part number Surge Recommended Location Alarm Replacement

Rating Contacts Module
DSD11001S275 100kA Main Panel, high lightning area, or exposed site No Not available
DSD1401S275 40kA Main Panel, lower lightning area, or unexposed No DSD1401S275M

site, or sub panel in high lightning area
DSD1401SR275 40kA Main Panel, lower lightning area, or unexposed Yes DSD1401SR275M
site, or sub panel in high lightning area
DSD1101S275 10kA Sub-panel No DSD1101S275M
Common specifications
Module Width: 17.5mm
Terminals: up to 35 mm2 (solid), 25 mm2 (stranded)
Maximum Continuous Operating Voltage: 275Vac
Catalogue No. DSD11001S275 DSD1401S275 DSD1101S275
DSD1401S275M DSD1101S275M
69
www.nesco.com.au
CRITEC
Plug-in Protection
These Power Line Filters are used to provide the final stage of surge protection to electrical and electronic equipment
that connects via an AC power plug. The effectiveness of this simple-to-install protection is assured by virtue of it being
installed close to the equipment to be protected. The product is not the cheapest available, but it does offer excellent
surge ratings combined with series filtering.
The product provides a very solid 20kA surge rating in each of the three modes possible at an outlet (L-N, L-E, and N-E).
The protection in each of these modes uses MOVs in combination with robust thermal disconnects to provide increased
safety of the product.
In addition to the regular shunt protection that is used to divert the surge current to earth, this protector features series
filtering. This filtering further reduces the transient voltage getting through to the equipment, but also slows down the
rate of rise of that voltage, further protecting the equipment.
User convenience is built into this product, with LEDs indicating correct product operation, and mounting flanges
allowing wall mounting if required.
Where the equipment being protected has a telephone connection, it is very important that transient protection is
provided for both the AC power connection and the telephone connection. The PLFA2 RJ11 products provides this
combined protection. The telephone circuitry is approved and complies with ACA requirements. The telephone circuitry
is protected to the same rugged 20kA level as the AC power circuit. As well as a rugged gas arrester, the circuitry
features a solid state thyristor to provide instantaneous clamping of telephone line surges to low values, and
automatically resetting solid state fuses in series with each wire to provide overcurrent protection.
Specifications
AC Protection
Model : PRF A2
Nominal voltage: 240 Vac
Catalogue No. PLF A2
Maximum Continuous Operating Voltage: 275 VAC
Maximum Line Current: 10 A
Surge rating: 20 kA 8/20us in each of L-N, L-E, and N-E modes
Aggregate surge material: 80 kA
Dimensions: 275 mm x 100 mm x 72 mm
Weight: approx. 1.5 kg
Connection: Power cord, 2 m
AC Protection plus Telephone Line Protection

Model : PLF A2 RJ11
AC Protection as above
Telephone Protection: 20 kA 8/20us (L+L)-E Catalogue No. PLF A2 RJ11
Max. Telephone Line Current: 160 mA
Connection: 2 x RJ11 sockets
Dimensions: 320 mm x 100 mm x 72 mm
70
ERITECH SYSTEM 2000
Item Description Rod length Rod Pack U/M Unit Weight
Diameter Size Weight Units
CAR0510 AIR TERMINAL,CU,10x500mm - 711080 500 10 1 EA 0.48 KG
CAR0315 AIR TERMINAL, CU,15x300mm 300 15 1 EA 0.35 KG
CAR2015 AIR TERMINAL,CU,15x2000mm - 711010 2000 15 1 EA 3 KG
CMPR AIR TERMINAL,CU,15x500mm, MULTIPLE POINT 500 15 1 EA 1.02 KG
Catalogue No. CMPR

Catalogue No. CAR-AAR
Franklin Rods Bases and Brackets

Item Description Suit Rod Pack U/M Unit Weight
Diameter Size Weight Units
ATBC10 BASE,AIR TERMINAL,CU,10MM - 711150 10 1 EA 0.5 KG
ATBC15 BASE,AIR TERMINAL,CU,15MM - 711160 15 1 EA 0.5 KG

COPPER
RSC115 BASE,AIR TERMINAL,CU,15MM, RIDGE - 15 1 EA 1.07 KG

711170
TTRC16 COUPLER,AIR TERM,CU,15MM, THREAD ROD/ 15 1 EA 0.23 KG

TAPE
CBR015 BRACKET,AIR TERM,GM,15MM, PAIR - 711190 15 set 2 EA 0.9 KG
Catalogue No. ATBC Catalogue No. RSC Catalogue No. TTRC Catalogue No. CBR
71
www.nesco.com.au
ERITECH SYSTEM 2000

Copper Downconductors
Item Description Width Thickness Roll U/M Unit Weight
Weight Units
TC-EC-2530-50 TAPE,CU,25X3MM,ANNEALED, 25 3 50 MT 34 KG
50M ROLL
TC-ECT-253 TAPE,CU,25X3MM,TINNED, 30M ROLL 25 3 30 MT 21 KG
Catalogue No. TC-EC & TC-ECT
Downconductors Fixings
Item Description Suit Tape Pack U/M Unit Weight
Size Size Weight Units
DCC253 CLIP,TAPE,CU,25X3MM,DCC - 711220 25 x 3 50 EA 0.06 KG
DCA253 CLIP,TAPE,AL,25X3MM,DCC - 711730 25 x 3 50 EA 0.03 KG
PDC253BN CLIPS,TAPE,PL,25X3MM,DC, BROWN - 711280 25 x 3 50 EA 0.01 KG
PDC253GY CLIPS,TAPE,PL,25X3MM,DC, GREY - 711290 25 x 3 50 EA 0.01 KG
Catalogue No. DDC-DCA Catalogue No. PDC
72
Downconductors Fixing Clamps
Item Description Suit Tape Pack U/M Unit Weight
Size Size Weight Units
STC253 CLAMP,TAPE,CU,25X3MM, SQUARE - 711410 25 x 3 5 EA 0.2 KG
STA253 CLAMP,TAPE,AL,25X3MM, SQUARE - 711400 25 x 3 5 EA 0.1 KG
OBC268 CLAMP,TAPE,CU,26X8MM, OBLONG - 711440 26 x 8 2 EA 0.29 KG
OBA268 CLAMP,TAPE,AL,26X8MM, OBLONG - 711440 26 x 8 2 EA 0.29 KG
PCT400 CLAMP,TAPE,CU,26X12MM, PLATE - 711450 26 x 12 1 EA 0.6 KG
BIM700 CONNECTOR,TAPE,CU/AL, 25X3MM, BIMETALLIC 25 x 3 5 EA 0.19 KG
BBBC B-BOND,CU,26MM - 710260 26 25 EA 0.12 KG
Catalogue No. BIM

Catalogue No. STC-STA
Catalogue No. PCT Catalogue No. BBC Catalogue No. OBC-OBA
Catalogue No. LPC122

Smooth Weave Sysmtem
Catalogue No. LPC2855F5M Catalogue No. LPC305 Catalogue No. LPC30958

73
www.nesco.com.au
ERITECH SYSTEM 2000

Smooth Weave System Components
Item Description Rod Rod Pack U/M Unit Weight
length Dia. Size Weight Units
LPC411 AIR TERMINAL,CU,5/8X18IN 18 5/8 1 EA 1.6 LB
LPC413 AIR TERMINAL,CU,5/8X36IN 36 5/8 1 EA 3.3 LB
LPC30958 BASE,AIR TERMINAL,BR,5/8IN, ADHESIVE 5/8 1 EA 1 LB
LPC2855F5M ADAPTOR,AIR TERMINAL,CU, 5/8IN,F/M, 5/8 1 EA 7 OZ

SWIVEL
LPC30558 BASE,AIR TERMINAL,BR,5/8IN, UNIVERSAL 5/8 1 EA 12 OZ
LPP899R ADHESIVE CEMENT, RUBBER, FOR AIR 1 EA 1 GAL

TERMINAL BASE
LPC122 250FT CABLE,SMOOTHWEAVE, 1/0 250ft FT 55 LB

AWG,250FT
LPC122L 250FT CABLE, SMOOTHWEAVE, TINNED 1/ 250ft FT 55 LB

0 AWG,250FT
Notes: LPC122 compliant with AS1768-1991 table 4.4. Suitable for use as a main current carrying conductor, for air
terminations and downconductors.
LPC516 CLAMP,CABLE,SMOOTHWEAVE 1 EA 2 OZ
PARALLEL,BRONZE
LPC595 SPLICER,CABLE, 4 WAY, SMOOTHWEAVE 1 EA 9 OZ
LPC804 CLAMP,CABLE,CU, SMOOTHWEAVE 100 EA OZ

C122,2 HOLE
LPC810 CLIP, CABLE, CU, 35mm, ADHESIVE 1 EA OZ
Catalogue No. LPC595 Catalogue No. LPC810 Catalogue No. LPC804 Catalogue No. LPC516
74
O v e r h e a d a nd Un d er g r o u n d
Cable Jointing Pits & Lids

The range of plastic cable jointing pits are used in conjunction with concrete or steel covers to house, protect and give
ready access to power and communications cables at underground jointing locations. They offer many advantages over
traditional fibre reinforced cement pits and a much greater life expectancy. The pits are light in weight and can be easily
transported and stored. Installation is easy with no special tools being required. The design embodies special ribbing for
on site strength and stability. The pits are extendable.
Specifications
Part No Description Length Width Depth
P1 P1 Pit 419 155 350

P1Lide Lid Electrical 470 195
P1Lidc Lid Communication
PIT1LST* Lid Steel Tamperproof 470 190
PIT1LSL* Lid Steel Lockable
P2 P2 Pit 553 180 514

PIT2LST* Lid Steel Tamperproof 612 245 Catalogue No. P1, P2, P3, P4
P3 P3 Pit 663 243 570

P4 P4 Pit 584 281 760

J5 J5 Pit 650 330 650

J5S J5 Split Pit
J5Lide Lid Electrical 645 395
J5Lidc Lid Communication
PIT5LSL* Lid Steel Lockable Split Pit
Riser 5 Riser for J5 650 330 200
J6 J6 Pit 1240 440 670

J6Lide x 2 Lid Electrical 650 500
J6Lidc x 2 Lid Communication
PIT6LST* x 2 Lid Steel Tamperproof 655 500
PIT6LSL* x 2 Lid Steel Lockable
PIT6LST*1 Lid Steel Tamperproof 1310 500
PIT6LSL*1 Lid Steel Lockable
J7 J7 Pit 875 440 1130

Catalogue No. J7
75
www.nesco.com.au
O v e r h ead an d Un d er g r o u n d
Specifications
Part No Description Length Width Depth
J8 J8 Pit 1240 440 8895

J9 J9 Pit 1915 440 895

J6Lide x 3 Lid Electrical 650 500 Catalogue No. J6
PIT6LST* x 3 Lid Steel Tamperproof 648
R430 R430Pit 430Dia 430Dia 600

R430Lid R430Lide 390Dia 390Dia
Pit 450 Pit 450 450 450 510

Pit 450CL Lid Concrete 550 550
Pit450SL Lid Steel 545 545
PIT450SLHDL Lid Steel Lockable H/D
PIT450SLLDL Lid Steel Lockable L/D
Riser450 Riser for 450 450 450 300
Pit 600 Pit 600 600 600 660

Pit600CL Lid Concrete Plain 695 695
Pit600CLE Lid Concrete Electrical
Pit600SL Lid Steel
PIT600SLHDL Lid Steel Lockable H/D
PIT600SLLDL Lid Steel Lockable L/D
Riser600 Riser for 600 600 600 300
JTEEBAR Teebar For J6, J8 & J9
PIT7TBAR Teebar for J7
Accessories
MPK500 Lid lifter Catalogue No. MPK500

Note: * is replaced by an e for electrical or c for communication
or t for Telstra Lids available.
Catalogue No. EMARKER Catalogue No. TMARKER Catalogue No. DANGER SIGN
76
Underground Residential Distribution
The all weather polyethylene construction requires no painting or maintenance, as protection against
corrosion/moisture is not an issue.
The strong but light base and turret allow easy transport and installation. The turret is easily and simply
secured to the base with D head stainless steel screws. The panels are resilient and easily drilled.
The standard colour is green. (however beige* is available)
Accessories
Part No Description
URDQ1 Complete Short Turret Assembly - includes Turret, Base, Blank Type X panel & 4 D Head bolts
URDQ2 Complete Tall Turret Assembly - includes Turret, Base, Blank type X panel & 4 D Head bolts
URDQ1-3F Complete Short Turret Assembly - includes Turret, Base, 3 Fuse panel fitted with 3 fuse holders
& 1 neutral link & 4 D Head bolts
URDQ2-6F Complete Tall Turret Assembly - includes Turret, Base, 6 Fuse panel fitted with 6 fuse holders
& neutral link & 4 D Head bolts
*For beige add b after above P/N
Individual Components & Accessories

Specifications
Part No Height Width Depth Wt-kg
Turrets
UTSMALL 315 235 300 1.9
UTTALL 550 230 295 2.9
Matching Base
UTBASE 350 550 510 3.6
Accessories
Part No Description
Bolts
DHB10M Stainless Steel D Head bolt M10 x 30mm length
Panels
CTC280 Blank Type X switchboard panel 280 h x 205 w
CTC495 Blank Type X switchboard panel 495 h x 205 w
3F-MPS-AS-SQ 3 fuse panel fitted with 3 x fuse holders & neutral link
6F-MPM-AS-SQ 6 fuse panel fitted with 6 x fuse holders & neutral link
Shrouds
ISP-BK-LG-5mm Termination shroud Black fire retardant PVC
150mm long x 90mm O.D.
ISP-BK-SM-5mm Termination Shroud Black fire retardant PVC Catalogue No. 3F-MPS
90mm long x 66 mm O.D.
D-Head
Bolt Spanners
DSC-M10 D Head Drill Socket attachment
3F-MPS T-handle spanner 780mm length suits all D Head bolts
77
www.nesco.com.au
Underground Industrial/ Commercial Pillars

Pillars and base are fire retardant and UV stabilised.
Pillars are marked Danger Electricity
Available pillar colours green / beige
Accessories
Part No Description
FPBNF1V Fibreglass pillar vented
Pillar Dimensions 760H x 450W x 33D
FPBNF1V1D Fibreglass pillar vented single door
FPBNF1V2D Fibreglass pillar vented two door
FPBNF2V1D Fibreglass pillar vented single door
Pillar dimensions 1300H x 450W x 330D
FPBNF2V2D Fibreglass pillar vented two door
GSFPNF1 Type X S/Panel Blank/Frame Assembly (to suit FPBNF1 series)
700H x 410W x 10mm
GSFPNF2 Type X S/Panel Blank/Frame Assembly (to suit FPBNF2 series)
1200H x 410W x 10mm
CBNF1 Lightweight concrete base to suit FPB series
310H x 565W x 335D colour neutral
PSFB2 Security bolts & washers 4 per pillar G304 stainless steel
SLP1 Locking plate to suit padlock 1 per pillar G304 stainless steel
SLB1 Locking bolt for SLP1 1 per pillar G304 stainless steel
Pillars and base are fire retardant and UV stabilised.

Pillars are marked Danger Electricity
Available pillar colours green / beige
Accessories
Part No Description
FPB3CD1D Fibreglass pillar single door
FPB3CD2D Fibreglass pillar two door
GSFP3 Type X S/Panel Blank/Frame Assembly
1100H x 625W x 10mm
CB3 Lightweight concrete base
400H x 960W x 500D colour neutral
PSFB2 Security bolts & washers 4 per pillar G304 stainless steel
Other sizes and configurations available upon request
78
Earthing Rods & Accessories
Part No Description
Domestic Non-Extendable Earth Rods
CUP1314WC Copper domestic earth rod 13mm diameter

1.4m length complete with earth clip 10 pcs/pack
CUP1318WC Copper domestic earth rod 13mm diameter

1.8m length complete with earth clip 10 pcs/pack
Extendable Earth Rods & Accessories
CR 1518 Tapered copper earth rod 15mm diameter x 1.8 length
CR 1524 Tapered copper earth rod 15mm diameter x 2.4 length
CR 1530 Tapered copper earth rod 15mm diameter 3.0m length
BC15 Coupling
TP15 Driving point normal driving
TPS-15 Driving point hard driving
DHT15 Driving Head
Non Extendable Heavy Duty
CR1918 Copper rod 19mm diameter x 1.8m length

incorporates driving head and point


Note: The above is a rationalisation of the entire earth rod range. For other
configurations please consult sales office.
Airport Earthing Terminal
AIR1918 Copper rod 19mm diameter x 1.8 length complete

with earthing terminal
Type AET Electrodes provide for the earthing of

airport tarmac areas where any generation of static
electricity could be hazardous, i.e. aircraft refuelling,
servicing and cargo loading areas. The heavy duty
capping has a ribbed design affording a fast, and
positive earthing connection by means of earth lead
connector clips.
Material: Solid steel core overlaid with copper

cladding; heavy bronze cap.
Installation Procedure: Drive electrode into ground

to required depth. Remove protuding portion of rod
above cap and finish flush. Catalogue No. AIR1918
79
www.nesco.com.au
ECA
Part No Rod Dia. Cable Range Weight (kg)
ECA 1508 13 - 15 16 - 50mm2 0.160

2
ECA 1514 13 - 15 *35 - 150mm 0.145
ECA 1514C 13 - 15 *35 - 150mm2 0.150
A versatile double saddle clamp made of copper alloy

Catalogue No. ECA 1514
with stainless stell U-bolt and nuts.
*Smaller cables within the range 16 - 35mm2 can be
accommodated in Cat. No. ECA 1514 and ECA 1514C by
inverting clamp casting.
ECR
ECR5 13 - 15 10 - 50mm2 0.115
A single screw earth clamp. Both componenets made

from brass.
ECP Catalogue No. ECR 5
ECP 1309 12 - 13 16 - 50mm2 0.112

2
ECP 1509 14 - 15 16 - 50mm 0.125
ECP 1914 17 - 19 16 - 120mm2 0.200
Cast in copper alloy with stainless steel U-bolt, nuts and

spring washers.
ECH
ECH 1914 15 - 19 50 - 120mm2 0.350
Type ECH 1914 takes two cables at right angles to rod. Catalogue No. ECP 1514
Castings are in copper alloy. U-bolt, nuts and spring
washers are stainless steel.
ECX
ECX 1909 13 - 19 16 - 50mm2 0.300
ECX 1514 13 - 15 35 - 120mm2 0.300
ECX 1914 13 - 19 35 - 120mm2 0.320
Type ECX clamps take cables either at right angles or

parallel to rod. Castings are in copper alloy. U-bolt, nuts
and spring washers are in stainless steel.
Catalogue No. ECX 1914
ECF
ECF 13 13 Two holes 0.226
11.5mm dia.
ECF 15 15 0.225
on 30mm
ECF 19 19 centres 0.224
Type ECF clamps are designed to connect an earth rod to

an earthing strap which is drilled to match U-bolt.
Casting is copper alloy. U-bolt, nuts and spring washers
are stainless steel.
Catalogue No. ECF 13
80
Compression Earth Clamps
Made from high conductivity copper. Used where copper earth wire
is looped so as not to cut the earth wire, ensuring continuity of the
Earthing System. Suits a vast range of conductors and earth rods,
12mm to 15mm dia. inclusive.
6 Profile Earthing Connector

For Cable - Cable or Rod Cable Connection.
Specifications
Part No Rod Dia. Cable Size Die
CO/16 12 to 15mm 16 sq mm Profile 6
CO/25 12 to 15mm 25 sq mm
CO/35 12 to 15mm 35 sq mm U-997
CO/50 12 to 15mm 50 sq mm or
CO/70 12 to 15mm 70 sq mm DU1315
CO/95 12 to 15mm 95 sq mm Profile C
CO/120 12 to 15mm 120 sq mm
C Profile Earthing Connector

For Rod to Cable Connection.
Specifications
Part No Rod Dia. Cable Size Die
C35/70 12mm 25 sq mm U-O/DUOT
C70/95 12 to 15mm 50 - 70 - 95 U-997/
sq mm DU1315
Earth Rod is compressed with hexagonal die prior to connection of clamp
to avoid radial turning of clamp after earth connection is completed.
Hexagonal Die Dimensions

12mm Diameter rod - use 38 - 130 (13mm A/F) Hex Compression Die
15mm Diameter rod - use 38 - 142 (14.2mm A/F) Hex Compression Die
For Cable to Cable Connection.

Specifications
Part No Cable Run Cable Tap Die Size
C35/70 70 sq mm 35 sq mm U-O
50 sq mm 50 sq mm or
70 sq mm 50 sq mm DUOT
C70/95 70 sq mm 70 sq mm UO997
95 sq mm 70 sq mm or
95 sq mm 95 sq mm DU-1315
E Profile Earthing Connector

For Cable to Cable Connection.
Specifications
Part No Cable Run Cable Tap Die Size
E50/70 50 sq mm 50 sq mm
70 sq mm 50 sq mm U-O
70 sq mm 70 sq mm
81
www.nesco.com.au
Earth Rod Connection Boxes

Catalogue No. PIT-03
Part No Description
ERB1 Aluminium Alloy casting 76mm high x 120mm wide x
120mm depth features a hinged lid
PIT-03 Plastic 245 high x 190 wide x 145mm depth Withstands

5 tonnes Lockable lid
Catalogue No. ERB1
Earth Enhancing Compound
Part No Description
Earthit 20kg bag Mixture of Bentonite, Gypsum and Sodium Sulphate
Features stable high conductivity providing long term low

ground resistance. High expansion, low shrink characteristics,
Non-toxic, Non-corrosive.
Apply as a dry mix or as a pourable slurry
Material Safety Data sheets are available upon request

1 bag mixes 0.03m3
Catalogue No. Earthit
Earth Mats
Part No Description
EMAT Galvanised mild steel 1525mm x 915mm
Catalogue No. EMAT
Earth Bond
Part No Description
C70 For Commercial earthing installations - The earthing bond
system provides an earth connection to the steel reinforcement,
offering a virtually indestructible, stable and low resistance
path to earth
Bonding cable - 70mm
3 sec current rating - 10kA
Lug dia - 10mm
Terminal thread - M10
Thread depth - 20mm
Catalogue No. C70
82
Copper Tape
Part No Description
TCEC253050 Tape, copper - 25 x 3mm (50m roll)
TCEC2530100 Tape, copper - 25 x 3mm (100m roll)
CET-50 Tape, copper - 50mm x 0.5 - available per meter
Flexible Copper Braids

The flexible copper braids are made from numbers of flat tinned braids.
Ferrules are pressed on the ends to form flat connection plates to bolt
onto bus-bars or terminals. (12mm hole std)
Profile 6
Part No Current Rating No of Braids
FCB1-100/300 100 Amps 1
FCB1-200/300 200 Amps 2
FCB1-275/300 275 Amps 3
FCB1-350/300 350 Amps 4
FCB1-425/300 425 Amps 5
FCB1-500/300 500 Amps 6
Note: Standard length is 300mm. Other lengths are available upon request.
FBCB1 prefix denotes a single hole. For 2-hole use prefix FCB2
Catalogue No. FCB1
Transformer Braid & Adaptor Plates

Catalogue No. RCB3-670S
Part No Description
RCB3-670S 670 amp 315mm in length
AP670 Adaptor plates to suit the above 170mm x 100mm
Catalogue No. AP670
83
www.nesco.com.au
Cadweld Exothermic Welding

The Cadweld Process makes it possible to produce copper/copper,
copper to aluminium, copper/steel and aluminium/aluminium
electrical molecular bonds with no external energy or heat source.
Information Required for Orderin

1. Connection type
2. Conductor material, size & stranding
3. Ground Rod size
4. Lug catalog number
5. Pipe, nominal size, vertical or horizontal
6. Rebar, nominal size
Four Simple Steps

Step 1 Prepare conductor ends with a wire brush for welding.
Place cable ends into open mould.
Step 2 Close handle to lock mould halves together. Drop metal

disk into crucible ensuring it is correctly seated, covering
tap hole.
Step 3 Deposit weld metal into crucible. Tap bottom of container

to release starting material. Spread a little material on
top of mould.
Step 4 Close the cover and ignite with flint gun. Open the mould
after 10 seconds, when meal has solidified.
Cable Grips & Accessories

Range of hand woven wire cable grips is designed for hauling power
cable, telephone, fiber optic cable, coaxial cable and winching rope
through conduit, trenches and overhead poles. High quality galvanized
steel wire is used in weaving the individual grips.
84
Closed Tubular Single Eye and Double Eye
These are for light to medium hauling of communication and power cable.
Specifications
Part No Suit cable Max S.W.L. Max
Single & Double O.D. Length in kN Tensile
in mm in mm Load in Kg
TCG-0612 & DCG-0612 6-12mm 300 6.48 1984
TCG-0916 & DCG-0916 9-16mm 350 8.89 2720
TCG-1422 & DCG-1422 14-22mm 400 13.33 4080
TCG-2032 & DCG-2032 20-32mm 550 16.59 5080
TCG-3240 & DCG-3240 32-40mm 700 13.33 4080
TCG-4055 & DCG-4055 40-55mm 850 19.91 6096
TCG-5575 & DCG-5575 55-75mm 950 29.87 9144
TCG-7595 & DCG-7595 75-95mm 1000 40.77 12480
TCG-95114 & DCG-95114 95-114mm 1200 61.15 18720
TCG-114126 & DCG-114126 114-126mm 1300 81.54 24960

Catalogue No. TCG
Lace Up - Double Eye

Generally used to support electricity cable in vertical or sloping position and
is also ideally suited for use in manholes where the longitudinal movement
of cable caused by road vibration needs to be checked.
Specifications
Part No Suit cable Max S.W.L. Max
O.D. Length in kN Tensile
in mm in mm Load in Kg
LCG-0612 6-12mm 300 6.48 1984
LCG-0916 9-16mm 350 8.89 2720
LCG-1422 14-22mm 400 13.33 4080
LCG-2032 20-32mm 550 16.59 5080
LCG-3240 32-40mm 700 19.91 6096
LCG-4055 40-55mm 850 29.87 9144
LCG-5575 55-75mm 950 40.77 12480
LCG-7595 75-95mm 1000 61.15 18720 Catalogue No. LCG

LCG-95114 95-114mm 1200 81.54 24960
LCG-114126 114-126mm 1300 125.64 38460

85
www.nesco.com.au
Swivels
The swivels have been manufactured with sealed bearings and are
precision machined from high-grade steel. They have been NATA
certified for a 3:1 safety factor.
Part No Description
SWI-16 6kN Swivel Clevis to Clevis
A range of fuses from 0.6kN to 62kN are available for the SWI-16 through to SWI-60.
The tolerances on the fuses have been rated at 10%. By removing the high tensile
bolt from the center, and replacing it with the fuse of your choice, you can convert
the swivels into a Breakaway Fused Swivel.
Catalogue No. SWI
Cable Support Rollers

Features
Aluminium cast rollers
Semi high tensile steel 18mm axle
Axle supported in sealed roller bearing
Specifications
Part No Height Width Depth Wt-kg
C1 190 280 400 5
C2 320 280 330 5
C3 320 250 155 5.5
86
Fiberglass Duct/Conduit Rod Tigerod
The fiberglass rod is supplied with detachable pulling eyes. TIGEROD
is detachable and comes in 4mm, 6mm, and 8mm rod. All methods of tracing
conduit from the ground will work with TIGEROD.
All rod has a 1mm sheath of yellow HPDE to render it more noticeable and to
protect the fiberglass from wear. The tigerod dispensing units come with a hand
brake and are strong and durable. The pay-off mechanism on the dispenser has
a double set of rollers to reduce wear on the sheath and rod. The rod is supplied
with the dispenser units. They are short enough to be stored in the back of panel
vans and other small, enclosed vehicles.
The rod comes standard with a 1mm copper tracer wire. Simply energize the rod
with your transmitter and locate your pipe with the aid of a receiver.
Pull rating up to 6.5kN at 2:1 safety factor.
Part No Rod O. D. Length

TDUS-4080 6mm 80 Meters

Catalogue No.TDUS-8200
Catalogue No.TDUS-6125
Electricians Mini Coil

Extremely versatile for electrical, telephone and computer network installations
in commercial situations. Outperforming steel and nylon fish tapes, the 3mm
mini-coil comes complete with end fittings and a lightweight-dispensing reel.
Part No Rod O. D. Length

Catalogue No. TDUS-4080
Catalogue No. TDUS-3060

87
www.nesco.com.au
SICAME Insulated Line Systems

Mains Connection Boxes
Single and three phase environmental base and cover for the protection
on consumer mains. Each unit contains the HSC series (House Service
Connector) providing a full sealed bi-metallic connection of copper
consumer mains to Al or Cu services.
Features
Fully insulated and waterproof.
Plug in HSCs providing bi-metal connection of service
cables and consumer mains.
Base is suitable for rear entry of consumer mains.
Eliminates UV degradation of PVC consumer mains.
Heavy duty polymide UV stabilised construction.
IP66 rated.
Clear markings.
All connections made with 13mm across flats hexagon headed spanner.
Cover allows for easy exit of bonding tail HSC435/1
Specifications
Part No Description
MCB1/2H Single Phase Mains Connection Box with 2 x HSC435 connectors
MCB3/4H Three Phase Mains Connection Box with 4 x HSC435 connectors
MCB1 Single Phase Mains Connection Boxes without HSC435 connectors

Catalogue No. MCB1/2H
MCB3 Three Phase Mains Connection Boxes without HSC435 Connectors
Underground Multi-Tap Connectors

Multi position piercing connector for underground connection
of two and four service connections.
Features
Flexible joints providing the ultimate barrier to moisture ingression.
Insulation piercing on all positions. No stripping necessary.
Nickel plated interior body.
Ideal for pillar-box or underground pit.
Totally insulated and waterproof. Catalogue No. MUCI SERIES
Use RPS spanner see page 14
TTD Series
Part No No of Connections Cable Range Bolt Head Size AVAILABLE
MUCI2/650 2 6-50mm 13
QUEENSLAND
MUCI3/650 3 6-50mm 13 ONLY
MUCI4/650 4 6-50mm 13
88
House Service Connectors
House side connection - Stripped copper consumer mains
Service side connection - Aluminium or copper insulated service

connection made with insulation piercing technology thus stripping
of insulation is not required
Features
Shear heads on both connections.
Fully insulated, waterproof and bi-metallic.
Easily fits into Mains Boxes. Catalogue No. HSC435/1
Optional model available with insulated bonding tail and lug.
Specifications
Part No Consumer Mains House side only Service Side Tap Copper Earth Tail Bolt Head Size
side mm strip length Range mm
HSC435 4-35 10mm 6-35 No 13mm A/F
HSC435/1 4-35 10mm 6-35 16mm 13mmA/F
Overhead Pole/ House Fuse

100-amp single pole pigtail stick operated service fuse for house or pole mounting.
Features
Range of brackets to suit all installations including replacement.
Insulation piercing connections on line and load sides.
Insulated top mounting M8 shear head bolts.
Takes up to 100 amp BS style cartridge (57mm x 22mm).
U.V. Stabilised polymeric body.
Gangable to three phase.
Specifications
Part No Description
PF100 Pole fuse up to 100 amp
PFBKT1 Pole bracket - single phase
PFBKT3 Pole Bracket - three phase
PFAB1 Adapter bracket to fit PF100 to swan neck pin
AVAILABLE
QUEENSLAND
ONLY
Catalogue No. PF100
89
www.nesco.com.au

Insulated Piercing Connectors
For joining insulated mains cable to insulated service cables.
TTD Series
Mains - Insulated copper or Aluminium Tap - Insulated Copper or Aluminium
Features
Easy and safe to fit on energised cable. Shear heads on all bolts.
No live metal parts are accessible and Tightening bolts are potential free.
there is no need to strip the insulation.
Simultaneous piercing on main and tap. End cap for protection of tap
Completely waterproof. Use RPS spanner see page 14
Withstands 6kV in water.
For joining bare mains cable to insulated service cables.
NTD Series
Mains - Bare Copper or Aluminium Tap - Insulated Copper or Aluminium
TTD Series
Part No Mains Cable mm2 Branch Cable mm2 No of bolts
TTD051FAX 16-95 1.5-10 1
TTD101FAX 6-54 4-35 1
TTD151FAX 25-95 6-35 1
TTD201FAX 35-95 25-95 1
TTD231FAX 25-95 10-50 1
TTD241FAX 50-150 6-35 1
TTD251FAX 50-150 35-95 1
TTD301FAX 35-95 35-95 2
TTD341FAX 50-150 6-35 2
TTD351FAX 50-150 35-95 2
Catalogue No. TTD
TTD401FAX 50-185 50-150 2
TTD431FAX 70-240 16-95 2
TTD451FAX 70-240 50-185 2
NTD Series
Part No Bare Cable Type Bare Conductor mm Insulated Cable
NTD101F Cu 7-54 6-35
NTD151F Cu 35-95 6-35
NTD241F Cu 50-150 6-35
NTD301FA Cu 7-95 35-95
NTD351F Cu 50-150 35-95
NTD401F Cu 50-150 50-150
NTD101AF Alu 7-54 6-35
NTD151AF Alu 35-95 6-35
NTD241AF Alu 50-150 6-35 Catalogue No. NTD
NTD301AF Alu 7-95 35-95
NTD351AFA Alu 50-150 35-95
NTD401AF Alu 50-150 50-150 AVAILABLE
NTD431AF Alu 95-240 35-95

QUEENSLAND
NTD451AF Alu 95-240 95-150 ONLY
Use RPS spanner see page ?
90
CCW and CAW Series
For joining bare mains cable to insulated service cables.
CCW Series
Bare copper to insulated PVC or XLPE copper

or aluminium service cable.
CAW Series
Bare aluminium to insulated PVC or XLPE copper

or aluminium service cable.
Features
Aluminium cast rollers
Piercing on all tap connectors
Conforms to Australian Standard AS4396
Catalogue No. CAW235 Catalogue No. CAW35
Disconnection of service by easy removal
of the connecctor from the mains
Bi-metallic tap section
Simple M8 socket operation
Two tap (CAW235) available
Specifications
Part No Mains Range O.D. mm Tap Range Shear
Heads
CAW235 7/1.75 to 19/3.75 A1 5-19 2 x 6-35mm2 A1/Cu Yes
CAW35 7/1.75 to 19/3.75 A1 5-19 1 x 6-35mm2 A1/Cu Yes
CCW35 7/1.00 to 19/3.00 Cu 3-14 1 x 6-35mm2 A1/Cu Yes

Catalogue No. CCW35
Suspension Clamps
Features
Suitable for angles up to 30 degrees
Hinged aluminium alloy body with stainless steel fasteners
Reinforced hanging eye to stop wear through vibration
Specifications
Part No Cable Size mm
2 Core 3 Core 4 Core
SC435 50 35,50 25,35
SC450 50
SC470 95 70 AVAILABLE
SC495 95
QUEENSLAND
ONLY
SC4150 150
91
www.nesco.com.au

Strain Clamps for Service, ABC Mains & Sub Mains
Part No Cable Size mm Features

PC63F27A 2 x 6 to 4 x 35 Wedge action
Range taking - one clamp suits a range

of cable sizes 2, 3, or 4 core cables
Suitable for everyday loadings
Suits closed or open eye pole supports
Simple to install Catalogue No. PC63F27A

BCST-2025-3PA 2 x 25 Bolted action
Can be used as a suspension

fitting by rotating blocks
Simple to install
BCST-4035-3PA 4 x 25 and Bolted action

4 x 35 Catalogue No. BCST-2025-3PA
Can be used as a suspension
fitting by rotating blocks
Simple to install
PA10/1 4x25-50 and Bolted action for full tension

2 x 25-50
Removable clevis pin
Aluminium strap Catalogue No. BCST-4035-3PA
17mm across flat nuts suit

ratchet spanner
PA11/1 4 x 50-95 and 2 x Bolted action for full tension

50-95
Aluminium strap

ratchet spanner
PA122 4 x 95 -150 Bolted action for full tension
Aluminium strap

ratchet spanner
Catalogue No. PA11/1
AVAILABLE
QUEENSLAND
ONLY
92
Installation Accessories
Part No Description Features
6707BC Running Sheave Sheave can be used for all sizes of mains cable
for LV ABC and including 4 x 95 & 4 x 150mm cable on
bare conductor intermediate, angle or end poles.
Cast aluminium construction.
Can be mounted vertically or can be suspended.
Working Load 1134kg (2500lbs).
Safe and easy to adjust and use.
BR50-S Ratchet Buckle For the attachment of Sheave support bracket.

& Strap
Safe working load 21.6kN.
Webbing fixed at spool. Plate hook sewn to strap
and used for hooking onto attachment point.
Strap length 1200mm.
RPS13/17-6H Ratchet Spanner 13mm across flats and 17mm across flats in one
260mm length spanner.
RPS13/17-6HSH
Ratchet Spanner Reversible ratchet.
200mm length
Suits all sizes of insulation piercing connectors for
cables 1.5mm2 up to 240mm2, most strain clamps
and suspension clamps.
6 point hex (double sided).
Comfortable grip.
Well balanced, lightweight.
CS050 For 50mm2 Cable Stripping tool removes the tough

LV ABC polyethylene insulation of low voltage aerial
CS095
bundled cable.
For 95mm2
CS150
LV ABC Quick, safe and easy
For 150mmc
LV ABC
12870 Service Cable Conductor range 2 x 16 to 4 x 35mm

Comealongs
Maximum working load 200kg.
Failing load 1250 kg
PP1514 Insulated cable Reusable

test point
CIE100 Core separation Suitable for LVABC up to and

tool including 4 x 95mm
PMR87 Core separation Suitable for LV ABC up to and

wedge including 4 x 95mm
CES3 Cable end seal Each cap contains a compound

16-25mm providing complete waterproofing
and ensures cap retention on cable
CES4 Cable end seal

35-50mm
CES5 Cable end seal AVAILABLE

70-95mm
CES7 Cable end seal QUEENSLAND

120-150mm ONLY
93
www.nesco.com.au

Preinsulated Compression Sleeves
Features
Limited and full tension 24 to 150mm2
Suits common 12 tonne-crimping tool.
Specifications
Part No Mains Cable Size mm Die A/F mm
MJPT25CG 25 25 17.3
MJPT35-25CG 35 25 17.3
MJPT35CG 35 35 17.3
MJPT50-25CG 50 25 17.3
MJPT50-35CG 50 35 17.3
MJPT50CG 50 50 17.3
MJPT70-35CG 70 35 17.3
MJPT70-50CG 70 50 17.3
MJPT70CG 70 70 17.3
MJPT95CG 95 95 17.3
MJPT95CG 95 95 21.5
MJPT120CG 120 120 21.5
Catalogue No. MJPT SERIES
MJPT150CG 150 150 21.5
Preinsulated Bi-Metal Lugs

Specifications
Part No Cable Size mm Length Die A/F
CPTAU16 16 87 14.0
CPTAU25 25 87 14.0
CPTAU35 35 92 17.3
CPTAU50 50 92 17.3
CPTAU70 50 92 17.3
CPTAU70-21 50 115 21.5
CPTAU95 95 92 17.3
CPTAU95-21 95 115 21.5
CPTAU150 150 115 21.5 Catalogue No. CPTAU SERIES
AVAILABLE
QUEENSLAND
ONLY
94
Photo Electric Outdoor Lighting Controls
Built in time delay prevents false cycling caused by lightning flashes
or stray headlights.
Specifications
Housing: UV stabilized high-impact polypropylene
Photocell: I inch cadmium sulfide light sensitive
Turn-On: 1 to 3 foot candles
Turn-on/Turn-off Ratio:
Switch type: Single pole, single throw. Contact position at night normally closed.
Temperature Range: -40degree to 170degree F.
Power consumption: 1.1 watts average at 120 VAC.
Rated life: 5,000 operations minimum at rated load.
Voltage: 208-277
Rating: 1800VA
Specifications
Part No Description
P68275LA30 Photoelectric cell
M2AF Base to suit conforms to NEMA standards

Wood pole, cross arm or wall mounting
including all weather locking type receptacle.
Helical Fittings Deadends for Aerial Service Cable

Features
Specifically designed for weathering, corrosion and vibration performance,
tensile load and high temperature conditions.
Easy to install, economical and neat appearance.
Application
For terminating insulated aluminium or aerial copper service cables direct
to house j hook without the need for separate insulator installation.
There are no span limits in normal urban usage.
Twisted Conductors
Conductor
Area (sq mm) Construction Core Part No. Standard Pack Colour Code
6 2, 3 & 4 GSG-160-DI-19
10 red
10 2 GSG-160-DI-19
10 2, 3 & 4 GSG-180-DI-19
10 white
16 2 GSG-180-DI-19
16 3&4 GSG-220-DI-20 10 yellow
95
www.nesco.com.au
Power Line Aviation Markers - for Conductors up to 25mm

Two piece sphere clamps together around the conductor.
Intended for use in accordance with Standards Australia requirements.
Installation: On de-energised lines by hand installation or live line tools.
Part No Description
PAM30* 30cm Diameter
PAM60* 60cm Diameter
*Please indicate the colour required by adding the relevant suffix to the
catalogue number.
Standard Colours
W = White
Y = Yellow
R = Red
O = Orange
Fittings for Aluminium Based Conductors (AAC, AAAC & ACSR)

Deadends & Splices
Rated Holding Strengths:
On aluminium conductors of homogenous
stranding, the UTS of the deadend is equal
to that of the conductor.
On ACSR conductors, the holding strength of the

deadend is equal to 100% of the strength of the
Aluminium strands plus 10% of the strength of the steel core.
They are designed to terminate primary, secondary and neutral wire conductors.
AAC/AAAC ACSR Cond. Dia. (mm) Part No. Standard Pack Colour Code
7/1.75 - 5.25 AFG-053 50 purple
7/2.25 - 6.75 AFG-068 50 brown
7/2.50 - 7.50 AFG-075 40 blue
7/3.00 - 9.00 AFG-090-CL 40 red
7/3.75 - 11.25 AFG-113-CL 25 black
7/4.50 - 13.50 AFG-135-CL 15 green
7/4.75 - 14.30 AFG-143-CL 10 blue
19/3.25 - 16.30 AFG-163-CL 10 orange
13/3.75 - 18.80 AFG-188-CL 15 black
37/3.00 - 21.00 AFG-210-CL 10 red
19/4.75 - 23.80 AFG-240-LT-CL 10 blue
96
Fittings for Galvanised Conductors
Rated Holding Strengths: The UTS of the steel fitting approximates that of their equivalent conductors.
Typical Australian Conductor Standard

Strands Dia. (mm) Part No. Pack Colour Code
1/2.50 2.50 GFG-025-CL 50 blue
1/3.15 3.15 50
GFG--031-CL red
1/3.24 3.24
7/1.25 3.75 GFG-038-CL 50 green
3/2.00 4.25 GFG-043-CL 50 yellow
7/1.60 4.80 GFG-048-CL 50 black
3/2.75 5.50 GFG-055-CL 75 white
7/2.00 6.00 GFG-060-CL 50 yellow
7/2.75 8.25 GFG-083-CL 20 white
7/3.25 9.75 20
GFG-100-CL yellow/orange
19/2.00 10.00
7/3.75 11.25 GFG-113-CL 15 black
7/4.00 12.00 GFG-120 15 black
19/2.75 13.75 GFG-138 10 white
19/3.25 16.25 GFG-163 10 orange
Splice for Galvanised Steel Conductors

Features
Easily applied Used for joining and repair
No special tooling required Long life
Same material as conductor
Conductor Stranding Conductor O.D. (mm) Part No. Standard Pack Colour Code
3/2.00 4.31 GFS-043 30 yellow
7/1.60 4.80 GFS-048 30 black
3/2.75 5.93 GFS-055 30 white
7/2.00 6.00 GFS-060 50 yellow
7/2.75 8.25 GFS-083 40 white
7/3.25 9.75 orange

GFS-100 25
19.2.00 10.00 yellow
7/3.75 11.30 GFS-113 20 black
7/4.00 12.00 GFS-120 15 black
19/2.75 13.80 GFS-138 10 white
19/3.75 16.30 GFS-163 10 orange
97
www.nesco.com.au
Splice for Aluminium & ACSR Conductors

When used with ACSR conductor this preformed conductor splice will hold a minimum tension amounting to the full
strengthof the aluminium strands plus 10% of the steel core strength.
Conductivity will be up to 75% that of the unspliced conductor:
Easily applied Used for joining and repair

No special tooling required Long life
Same material as conductor
Conductor Conductor Standard

Stranding O.D. (mm) Part No. Part No. ASCR Pack Colour Code
7/1.75 5.25 AFS-053 70 purple
3/4/1.75 5.25 AFS-053 70 purple
7/2.25 6.75 AFS-068 50 brown
7/2.50 7.50 AFS-075 35 blue
6/1/2.50 7.50 AFS-075 35 blue
3/4/2.50 7.50 AFS-075 35 blue
7/3.00 9.00 AFS-090 20 red
6/1/3.00 9.00 AFS-090 20 red
4/3/3.00 9.00 AFS-909-AW 20 red
7/3.75 11.25 AFS-113 25 black
6/1/3.75 11.25 FTS-113 10 black
4/3/6.75 11.25 AFS-113-AW 15 black
7/4.50 13.50 AFS-135 15 green
7/4.75 14.30 AFS-143 13 blue
6/4.75+7/1.60 14.30 FTS-143 13 blue
19/3.25 169.25 AFS-163 10 orange
30/7/2.5 17.50 FTS-175 15 blue
19/3.75 18.75 AFS-188 5 black
37/3.00 21.00 AFS-210 5 red
30/7/3.00 21.00 FTS-210 5 red
19/4.75 23.75 AFS-240 5 blue
98
Fittings for Agricultural Net Support Systems
Steel Line Splice
Specially designed splices give optimum strength while making them easy
to work with, as no special tools are required.
Specifications
Part No Conductor O.D. mm Colour Code Box Quantity
SLS0600S 6.10mm Yellow 50
SLS0735S 7.50mm Blue 30
Insulators & Line Hardware

Dimensions
Min Failing
Part No A B C D E Thread Pin Load
Low Voltage - Porcelain

SHLV1 54 57 39 17 R17 N/A N/A 9kN
SHLV2 76 80 54 17 R12 N/A N/A 20kN
PLV 91 82 52 N/A R11 Patt B B/100/3.5 7kN
Note:
Dimensions & Performance characteristics in accordance with AS3608, 1989.
Threads in accordance with AS2947.3, 1989.
Dimensions
Part No Voltage Creepage A B C D E Thread Pin Min F.L
High Voltage - Porcelain

P11 11kV 180 106 140 76 R13 R16 Patt A A/130/7 7kN
P22 22kV 420 168 228 113 R13 R16 Patt C C150/11 11kN
P33 33kV 534 194 279 113 R13 R16 Patt C C/200/11 11kN
Note:
Dimensions and Performance characteristics in accordance with AS2947, 1989.
Thread and Insulator Pin in accordance with AS1154, Part 2, 1985.
Catalogue No. PLV Catalogue No. SHLV Catalogue No. ???

99
www.nesco.com.au
Guy Strain Insulators - Porcelain

Dimensions
Part No A B C D E F G H I J K Min F.L
GY2 73 41 44 73 44 146 22 51 22 37 37 71kN
GY3 115 57 67 115 57 216 38 51 38 63 62 222kN
GY4 115 57 67 115 57 280 38 51 38 95 95 222kN
Note:
Dimensions and Performance characteristics in accordance with AS1137, Part 4 1981 AS3609, 1989.
Disc Insulators - Porcelain & Glass

Specifications
Part No Description Material Total Creepage Min F.L. Std Pack
D70S Ball & Socket 16mm Porcelain 295 70kN 6
D70C Tongue & Clevis Porcelain 295 70kN 6
D70SG Ball & Socket 16mm Glass 295 70kN 6
D70CG Tongue & Clevis Glass 295 70kN 6
Note:
Dimensions in accordance with AS2947, 1989.
Synthetic (Composite) - Distribution Strain Insulators

Specifications
Part No Nominal Voltage kV Number of Sheds Length mm Tensile Rating kN
1515-OH 11 4 315 70
2515-OH 22 6 440 70
3515-OH 33 10 525 70
10 0
Bus-Bar Insulators
Material
Stand off insulators are moulded from, recognised flame resistant fibreglass
reinforced polyester compound. They feature shatter resistance and height
tolerance closer than commonly available in porcelain insulators. Moisture
and heat resistance of insulators is higher than conventional plastic insulators.
Cantilever Strength
One end of the insulator is bolted to a flat plate and a force is applied to the
insert on the other end in a direction parallel to the end at a distance from the SM51
plate equal to the insulators height.
SM76
NOTE: the voltage rating is only meant to be a guide for indoor service. Insulators SM35
mounted within a suitable electrical cabinet are considered indoors even though
the cabinet is outdoors. An insulator will withstand its rated voltage continuously
but industry standards or other specifications may require a different spacing
from conductors of ground for a particular voltage. Wet or dirty conditions may
require derating an insulator.
Styles
Specifications SM35 SM51 SM76
Tensile Strength (lbs) 600 1000 1500
Torque Strength (ft lbs) 10 20 40
Voltage withstand 10 15 25
Screw (mm) 8 8 10
Weight 55 90 240
Insulator Pins
Shank Stem
Diameter Length Thread Thread
Length Length
Min
Part No Failure A B C J
Load
B100 3.5kN 16 140 50 98 B
A130 7 20 165 80 128 A
C1507 7 20 165 80 148 C
C15011 11 24 165 80 148 C
C20011 11 24 165 80 198 C
C3007 7 24 165 80 298 C
101
www.nesco.com.au
Line Hardware Eyebolts

All eyebolts are forged and then hot dipped galvanised to AS1650.
Supplied with nut.
Part No. and Diameter

Length mm 16mm O.D. 20mm O.D.
150 EB16X150
200 EB16X200
250 EB16X250
300 EB16X300 EB20X300
350 EB16X350 EB20X350
400 EB16X400 EB20X400
450 EB16X450 EB20X450
500 EB16X500 EB20X500
2000 EB20X2000
Catalogue No. EB
Eyebolts with Earth Tag

Specifications
Length mm Part No Diameter 16mm
250 EB16250T
350 EB16350T
450 EB16450T
650 EB16650T
Note: Supplied with 2 nuts and 2 washers

Catalogue No. EB C/W Earth Tag
Open Eyebolts / Hook Bolts

Part No. and Diameter
Length mm 16mm O.D. 20mm O.D.
250 OEB16X250
350 OEB16X350 OEB20X350
450 OEB16X450
Catalogue No. OEB
10 2
Service Hooks / J Hooks JHOOKCE
Specifications
Part No Description
CSH150 M12 x 150 Coach Screw (J Hook) JHOOKTTH
JHOOKCE M12 x 150 Coach Screw (Closed Eye Design)
JHOOKT M12 x 150 Coach Screw (J Hook) with Earth Tag
JHOOKTTH M12 x 150 J Hook with thread & 2 nuts & Earth Tag JHOOKT
LPIN M12 x 150 fitted with split pin & washer
IPSNG M12 x 150 Swan neck with Patt B thread
COMB M12 x 150 combination J hook fuse pin CSH150
Hook Bracket
Possible applications
Intermediate, angle or strain poles:
- banded to concrete poles with strainless steel strap
- bolted timber poles
Temporarily attached to concrete or timber pole with strap and ratchet
buckle assembly to support running sheave.
Conforms to the requirements for hook bracelets in AS 3766 - mechanical

fittings for low voltage aerial bundled cables.
Specifications
Part No Description
IBHB12 Hook Bracket 16mm O.D. 12kN Failing Load Catalogue No. IBHB
IBHB24 Hook Bracket 20mm O.D. 24kN Failing Load
Eye Nuts
Specifications
Part No Description
ENQ16 M16 Thread Catalogue No. ENQ

ENQ20 M20 thread
Crossarm Braces
Specifications
Part No Description
650T 650 x 40 x 6 Galvanised steel Crossarm Brace
1000T 1000 x 40 x 6 Galvanised steel Crossarm Brace

103
www.nesco.com.au
Gain Blocks
For mounting crossarms
Specifications
Part No Description
GB100 100 mm diameter Cast aluminium alloy
Pole Steps
Specifications
Part No Description
PLST M16 x 250 Drive in Pole Step
Galvanised Forged Bolts

Specifications
Part No Description
XOX (dia) (len) Available in 12, 16 & 20 mm diameter in various lengths.
Coachscrews
Specifications
Part No Description
CS (dia) (len) Available in 12 & 16mm diameter in various length
Washers & Nuts

Specifications
Part No Description
W12000FG M12 Galvanised Round
W16SQUARE 50 x 50 x 3 18mm hole Galvanised Square
W20SQU 50 x 50 x 3 22mm hole Galvanised Square
W20SQUARE 75 x 75 x 6 22mm hole Galvanised Square
N12 12mm nut
N16 16mm nut
N20 20mm nut
10 4
Shackle Straps
Specifications
Part No Description
STRAP190 Straight shackle strap 190 x 40mm
STRAP235 Offset shackle strap 235 x 40mm
SHSTRAP2 U Strap 130 x 80 x 6mm 1 x 18, 2 x 14mm holes
Aluminium Pole Caps

Specifications
Part No Description
AD301 Aluminium Pole Cap 300mm in diameter
Uniseal Jointing Compounds

For Aluminium and Copper Jointing
Electropars jointing compounds are formulated to improve jointing conductivity and
inhibit oxidation and corrosion between jointing contact areas. Jointing compound
should always be applied to the contact surfaces of all aluminium, aluminium to
copper and copper to copper connections prior to compression or bolting.
EP Uniseal (Grey, 350gm tube)

EP Uniseal consists of a lithium based 180C stable grease and zinc particles.
The base grease prevents water and contaminants interfering with the connection
and prevents the formation of surface oxides. The zinc particles work to break down
existing oxide on the conducting surfaces when those surfaces are brought together
under pressure. EP Uniseal is ideal for aluminium to aluminium and aluminium to
copper and copper to copper compression or bolted joints.
Quick Reference Chart

EP Uniseal is suitable for
Bolted Joints: Aluminium
Bolted Joints: Copper
Non Tension Compression Fittings
Use with solid Aluminium Conductors

Catalogue No. UNISEAL

105
www.nesco.com.au
Scratch Brushes
The use of a suitable scratch brush to remove any existing oxide film, dirt
or grease from the conductor is essential to ensure a sound electrical connection.
Specifications
Part No Description
ORB-1 White Scratch Brush for use on Aluminium
ORB-2 Black Scratch Brush for use on Copper
Split Bolt Clamps

Manufactured to E.S.A.A. specification from hard drawn brass. Accommodates
two maximum conductors specified in the table below. Electro tinned finish
can be supplied when specified.
Width
Part No. Max Conductor Size of Slot Std Pack
Electro Area Area
Natural Brass Tinned mm mm
B22Brass B22T 16 5.10 5.30 100
B24Brass B24T 35 7.65 8.30 50
B25Brass B25T 70 10.70 10.90 25
B26Brass B26T 95 12.46 12.90 20
B28Brass B28T 185 15.75 18.50 5
Aluminium to Aluminium Bolted Conectors

Aluminium Parallel Clamp Type APC
For combinations of aluminium and S.C.A. conductors. a heavy-duty aluminium clamp which uses stainless steel U-bolts
to provide high contact pressure over a wide conductor range. Tapered bell mouths and modified V-groove minimise
cold flow and prevent conductor strands from splaying.
Conductor Range
Run Tap
Weight
Part No. Stranding Overall Dia. Stranding Overall Dia. Each kg
APC 112 19/3.75 to 61/3.25 18.8 to 29.3 7/3.75 to 37/3.00 11.3 to 21.0 0.936
APC 1122 19/3.75 to 61/3.25 18.8 to 29.3 19.3.75 to 61/3.25 18.8 to 29.3 1.22
Catalogue No. APC

10 6
TO Series Clamps
These connectors are made form virgin ingot aluminium and are for equal and unequal conductors of aluminium.
Steel-cored aluminium and copper. Clamps are available with aluminium, stainless steel and galvanised steel hardware.
All clamps are supplied with FJ joining compound and sealed in plastic bags. When ordering clmaps with hardware,
use A for aluminum; SS for stainless steel and GS for galvanised steel.
Conductors
Part No. Run and Tap Diameter Length mm Weight kg
TO-4/12 7/1.35 to 7/3.75 4mm to 12mm 35 .1
TO-7/19 7/2.50 to 19/3.75 7mm to 19mm 51 .237
TOD-4/12 7/1.35 to 7/3.75 4mm to 12mm 70 .2
TOD-7/19
.475
TOD-7/19 SP 7/2.50 to 19.3.75 7mm to 19mm 95
.5
TODSC-7/19
TOT-7/19 7/2.50 to 19/3.75 7mm to 19mm 143 .8
Catalogue No. TO SERIES Catalogue No. TOD SERIES
Aluminium Line Clamps Type AL & ALD

A universal line tap for equal and unequal combinations of aluminium and ACSR conductors. Castings are high strength
aluminium alloy, hardware stainless steel. Prefilled with joint compound.
Conductor Range
Run Tap
Weight
Part No. Stranding Overall Dia. Stranding Overall Dia. Fig. Lmm Each kg
AL43 7/1.70 to 7/3.75 5.10 to 11.3 7/1.70 to 7/3.75 5.10 to 11.3 1 35 0.085
ALD58 7/1.75 to 7/4.50 5.25 to 13.5 7/1.75 to 7/4.50 5.25 to 13.5 2 70 0.142
ALD75 7/2.5 to 19/3.75 7.5 to 19.0 7/2.5 to 19/3.75 7.5 to 19.0 3 95 0.330
107
www.nesco.com.au
Aluminium to Copper Bolted Connectors

CTC Series - Consumer Tee Connectors
These connectors allow for multiple consumer connection to be made
where a number of split bolt clamps can be connected to the tinned copper
conductor compressed into main aluminium connector body. Connector
is cast in virgin ingot aluminium alloy. Available with aluminium, stainless
steel or galvanised steel hardware and supplied with FJ jointing compound.
Run Conductor Range

Copper Weight
Part No. Conductor Minimum Maximum kg
CTC-1-250 7/2.75 7/2.25 19/3.75 225
2CTC-1-250 7/2.75 7/2.25 19/3.75 350

Catalogue No. CTC SERIES
Aluminium to Copper Bi-Metal

PGI SERIES
Material is forged aluminium clamp friction welded copper insert for making
copper connections. The clamps have serrated transverse grooves for maximum
conductor contact and use galvanised steel bolts with Belville washers to prevent
thermal ratcheting under cyclic loads.
Conductor Range Dimensions
Aluminium Run Copper Tap

No & size
Part No. Area mm2 Overall Dia. Area mm2 Overall Dia. Length of Bolts
PGI 16072 16-70 5.1-11.7 6-50 3.0-9.0 40 2xM8
PGI 251502 25-150 6.3-15.7 10-95 4.1-12.5 48 2xM8
PGI 351853 35-185 7.5-17.5 35-185 7.5-17.4 95 3xM10
Catalogue No. PGI SERIES
Copper to Copper Bolted Connectors

Parrallel Groove Clamp
PG2595 M10 Single Bolt PG Clamp for joining Copper
Conductors 25-95sq mm to a 6mm flat surface
CPG-70-150 M12 Double Bolt PG Clamp for joining Copper
Conductors 70-150sq mm, 7mm, 1kg
CPG-120-240 M12 Double Bolt PG Clamp for joining Copper
Conductors 120-240sq mm, 72mm, 1.2kg
Catalogue No. PG2595
10 8
Copper to Copper Bolted Connectors
Type CBC
A heavy-duty bonding clamp that accepts a wide range of copper cables. Castings are high-strength copper alloy.
Hardware is stainless steel. Neoprene washers capture bolts, aiding installation.
Type CBC-X
A three-piece bonding clamp. the central spacer separates run and tap cables. Provides high contact pressure and
confines the cable strands. Castings are high copper alloy. hardware is stainless steel.
Type CPG - Two Bolt Clamp

Type PG - Single Bolt Clamp
Suitable for tap or parallel connections. Castings are high-strength copper alloy. Stainless steel bolts are captured for
single spanner instrallation.
Conductor Range
Run Tap
Weight
Part No. Area mm2 Overall Dia. Area mm2 Overall Dia. Each kg
CBC3 70 to 95 10.70 to 12.60 4 to 95 2.5 to 12.60 0.23
CBC4 120 to 150 14.21 to 15.75 16 to 150 5.10 to 15.75 0.425
CBC3X 25 to 95 6.42 to 12.60 16 to 95 5.1 to 112.60 0.27
Conductor Range
Weight
Part No. Area mm2 Overall Dia. Length Bolt Size No. of Bolts Each kg
CPG 2595 25 to 95 6.42 to 12.60 60 M10 2 .350
PG 2595 25 to 95 6.42 to 12.60 30 M10 1 .180
NOTE: The above range is for tap connections. When used for parallel connections the range
is 10mm2 to 95mm2 (4.05 to 12.60mm)
Catalogue No. CBC Catalogue No. PG2595
109
www.nesco.com.au
Rising Mains Connectors

Tee Off Connectors
Used in multi-level buildings where tee-off from main conductor is connected
to the main switchboard on each floor. For both Aluminium and Copper Mains
to Aluminium and Copper Tee. Made from High Strength Aluminium and
Gunmetal, fitted with stainless steel hardware. Belleville Washers fitted when
cast in Aluminium.
Please nominate Aluminium or Gunmetal when oredering by adding

an A or G to the end of Catalogue Number.
Tee off Copper or

Aluminium Main Aluminium
Part No. Minimum Maximum Minimum Maximum
RMC 55 19/1.53 37/2.03 7/1.35 19/1.53
35sq mm 120sq mm 10sq mm 35sq mm
7.65mm Dia. 14.21mm Dia. 4.05mm Dia. 7.65mm Dia.
RMC 86 37/2.25 61/2.25 7/1.35 19/2.14
RMC 104 61/2.52 61/2.85 7/1.35 19/2.14
Catalogue No. RMC SERIES
Bolted Connectors for Copper Cables

Versaclamp Type RV
A three piece multi-purpose Clamp providing parallel and T-connections over
a wide range of cable sizes. Casting are copper alloy. Hardware is stainless steel.
Cable Range
Main Tap
Area OD Area OD
Part No. Min Max Min Max Min Max Min Max
RV3 50 95 8.90 12.60 50 95 8.90 12.60
RV4 120 240 14.21 20.25 16 35 5.10 7.65
RV5 120 300 14.21 22.68 35 95 7.65 12.60
RV6 120 240 14.21 20.25 120 240 14.21 20.25
Catalogue No. RV SERIES
RV8 300 800 22.68 37.05 35 150 7.65 15.75
for tin plated connectors, add P to catalogue number: eg. RV4-P
Dimensions
Part No. Fig. B H J W
RV3 1 46 58 10 48
RV4 1 38 58 8 50
RV5 1 45 58 10 48
RV6 2 54 70 10 57
RV8 1 49 77 10 65
11 0
Distribution & Transmission Switchgear Dropout Fuses
Expulsion Type C
Standard Base Units & Accessories
Rated
Rated Rates Arc
Type Breaking Creepage to
Part No Voltage Current Bill kV. Shortening
Designation Capacity Earth mm.
(U) k V. (in) AMP Rod
kA. (sym)
72297/12 XS108 12 100 8/6 125 300 YES
72298/15 XS128 12/24 100 8/6 150 475 YES

72299/27 XS236 24/36 100 6/4 170 600 YES
Accessories
Part No Description
69196 Mounting Bracket - Standard Z
69196/3 Mounting Bracket - ZWA
69195 Mounting Bracket - NEMA
69194 Mounting Bracket - Direct to Pole
70584 Earth Support Kit. - Top M10 x 150mm Lg Stainless Steel.
69341/2 Earth support Kit. - Top M10 x 200mm Lg Steel HDG
69894/2 Earth Support Kit. - Bottom M10 x 120mm Lg Steel HDG
70450 Earthing Stirrup Kit. - Bottom
69961 Spark Gap Assembly
72906/12 Fuse Holder - 12/24kV 8/6kA 100A 366mm Lg.
(with ARC Shortening Rod)
72906/24 Fuse Holder - 24/36kV 6/4kA 100A 458mm Lg.
(with ARC Shortening Rod)
70410 Disconnect Blade - 12/24kV 300A 383mm Lg
71846/12 Replacement 12kV Fuse Holder for Older RE Style Dropouts
71846/24 Replacement 24kV Fuse Holder for Older RE Style Dropouts
Disconnector (Isolator)
Rocking Insulator Disconnector
3 Phase Open Airbreak Switch Type PR3
Accessories
Part No Description
69118 PR3 12kV 630 amp with Flicker Arcing Horns
Requires 21636 Crossarm Kit plus Operating Kit
69119 PR3 24kV 630 Amp with Flicker Arcing Horns
69120 PR3 36kV 630 Amp with Flicker Arcing Horns
Catalogue No. PR3
111
www.nesco.com.au
Distribution & Transmission Switchgear Dropout Fuses

Expulsion Type C
Isolators and Fused Isolators Standard Base Units & Accessories

Rated Rated Rated Rated Rated Clearance
Part No Type Short-Time voltage Current (Ie) Making Breaking to Earth
Current 1s (Ue) V AMP Capacity I/Ie Capacity I/Ie mm.
NZ4284 LVI 20kA 480 630 1 1 32

SEQEB
NZ4298 LVI 36kA 480 800 1 1 32
NZ4296 LVI 36kA 480 1600 32

SECV
NZ4286 LVFI 20kA 480 400 1 1 32

SECV
NZ4286 LVFI 20kA 480 630 1 1 32

SEQEB
NZ4211A LVFI 36kA 480 800 1 1 32
Accessories
Part No Description
69298/1 Compression Bolt Kit Qty. Reqd/Sw. = 2 or 4

M12 x 30 Bolt + Nut + Fl. & Sp. Washer S/S
69297/1 U Bolt Kit M8 S/S, Qty. Reqd./Sw. = 2 or 4

Clamp Range = 8 min. - 22 max.
69297/2 U Bolt Kit M8 S/S, Qty. Reqd./Sw. = 2 or 4

Clamp Range = 8 min. - 16.5 max
69293/1 Two Bolt Clamp M8 x 65 S/S, Qty. Reqd./Sw. = 2 or 4

Clamp Range = 3 min - 22 max.
69293/2 Two Bolt Clamp M10 x 65 S/S, Qty Reqd./Sw. = 2 or 4

Clamp Range =3 min. - 22 max.
71235 Single Bolt Cable Clamp Qty Reqd./Sw. = 2

Clamp Range = 5.1 min. - 22.7 max.
Disconnector Type UHSB (Unitised) with Pump Type Handle

Standard Base Units & Accessories
Crossarm Load Breaking Pole Mid Rated
Part No. Timber Steel Flicker Duogap Top Mtg Pole Voltage Normal BIL kV
Blade Mtg (U) kV
70209/1 12 630A 125
70209/15 12/24 630A 150
70209/16 12/24 630A 150
11 2
Fuselinks AK1 Expulsion fuselinks
Certificate of conformance to AS 1033.1 - 1990 Class AK1 @ 12kV & 24kV in
NGK STANGER C type Dropouts. Also suitable for use up to 36kV in single
& Dual Vented Dropout Units.
Specifications
AMPS Type K Speed AMPS Type K Speed
Description & Part No Description & Part No
1 ZXC705-01BK37 20 ZXC705-20BK37
2 ZXC705-02BK37 25 ZXC705-25BK37
3 ZXC705-03BK37 31 ZXC705-31BK37
5&6 ZXC705-06BK37 40 ZXC705-40BK37
8 ZXC705-08BK37 50 ZXC705-50BK37
10 ZXC705-10BK37 63 ZXC705-63BK37
12 ZXC705-12BK37 80 ZXC705-80BK37
16 ZXC705-16BK37 100 ZXC705-100BK37
AMPS Dual Range Surgeproof & Part No
3/10 (C) ZXC705-310BK37
6/20 (F) ZXC705-620BK37
10/30 (J) ZXC705-1030BK37
Where AK1 performance is not required use ZM instead of AK1 Fuselinks.

Catalogue No. ZXC705 Series
For Dual Range SURGEPROOF ratings with AK1 performance use:

3/10 (C) Dual Range SURGEPROOF instead of standard 3K Fuselink
6/20 (F) Dual Range SURGEPROOF instead of standard 6K Fuselink
10/30 (J) Dual Range SURGEPROOF instead of standard 10K Fuselink.
Application & Time-Current Data available on request.
Note: Flexible Head Adaptors Part No69231/1 (for 1-32 Amp Fuselinks) or 69231/2
(for 40-100 Amp Fuselinks) must be used with older style Top-Latched Dropouts Units.
Single Phase Hook Stick Operated Isolators (Disconnectors)

Single Insulator - Type MVI Standard Base Units & Accessories
Rated Rated Rates Creepage
Short Voltage Current to Earth
Part No current 1s (U) k V. (in) AMP Bill kV. mm.
70416 20kA 12/24 630 125 300
70414 20kA 24 630 150 475
70423/1 20kA 24/36 630 170 600
The above Part Numbers do not include Mounting Brackets and Clamps -
Refer to accessories table below.
70416NSW 20kA 12/24 630 125 300
70414NSW 20kA 24 630 150 475
The above Part Numbers include mounting bracket for underhung or 60
degree, c/w Flicker Horns & Earth Support - but no C- clamps - Refer to
accessories table over page.
113
www.nesco.com.au
Fuse Switch Disconnectors & House Service Units for LV ABC

Protection and Isolation
at transformer low voltage supply
at consumer feeder
at a change in cable conductor cross section
at a change from overhead to underground
short circuit protection
Sectionising
connection and disconnection of network sections
connection of overhead to underground
Single Phase
Part No Description Features
FSD100 100 amp IPC Terminal for 6-95mm2 AL/Cu cable

415V Fuse Accepts standard round fuse 22.2 x 57 BS1362 and can be operated using a pig tail
Switch type standard extractor stick
Disconnector Corrosion proof and weather resistant
FSD160 160 amp IPC Terminal for 6-95mm2 AL/Cu cable

415V Fuse Accepts DIN (NH) size 00 fuse links AS2005.21.1 and can be operated using
Switch a standard hook stick
FSD401 400amp Tunnel connector 2 x 50 - 185 mm2 Al/Cu cable

415V Fuse Accepts DIN (NH) size 1 & 2 fuse links and can be operated using a standard
Switch hook stick
FSD631 630 amp Terminal Palms suit lugs with M12

415V Fuse Accepts DIN (NH) size 2 or 3 fuselinks (630A max) and can be operated using a
Switch standard hook stick
Three Phase
FSD160-3 160 amp Assembled as 3 Phase Gang Operated Disconnector
415V Fuse IPC terminal for 6-95mm2 Al/Cu Cable
Switch Hinged lid accepts DIN (NH) size 00 fuse links AS 2005.21.1 and can be operated
Disconnector using a standard hook stick
Corrosion proof and water resistant
FSD250 250 amp Assembled as 3 phase Gang Operated Disconnector

415V Fuse IPC Terminals 95-150mm2/Tunnel Terminals 95-150mm2 or terminal palms available
Switch Hinged lid accepts DIN (NH) size 1 & 2 fuse links and can be operated using a
Disconnector standard hook stick
FSD400 400amp Assembled as 3 Phase Gang Operated Disconnector

415V Fuse IPC terminal 95-150mm2/ Tunnel Terminals 95-150mm2 or terminal palms available
Switch Hinged lid accepts DIN (NH) size 1 & 2 fuse links and can be operated using a
Disconnector standard hook stick
11 4
HSFEKIT House Service Fuse Extractor Kit - The Extractor
Features
For The extraction of House Service Fuses
Also used for disconnecting dropout fuses, isolators & fuse
switch disconnectors.
Can be used to attach the HP-275 proximity tester (page no ??)
The kit consists of 3 x 1.8 metre fibreglass Sticks
1 x 1.2 metre fibreglass sticks with sunrise fitting
1 x fuse extractor head
1 x 4 pocket yellow carry bag
Head section is rated at 100kV per 300mm and complies with IEC 855
Australian made
Catalogue No. HSFEKIT
Hot Sticks can be used for many applications on overhead powerlines and
a wide variety of specialised fittings and tools are available to suit the
sunrise head attachment.
Accessories
Part No Description
P10044 Disconnect hook for attachment to sunrise fitting
Other accessories available upon request
Catalogue No. P10044
Protective Cable Cover Tiger Tails

Work safely, prevent disasters and accidents caused by electric shocks by
covering high voltage electric wires with the DB Torapoli Pipe (tiger tails).
Features
The highly visible stripe design of yellow and black is recognisable
as a caution sign.
Its resistant against all types of weather.
Polyethylene ensures complete electric insulation. Catalogue No. TORAEA
Special shape and special-processed joint assure the permanent connection.
Any desired length can be achieved.
Easily coupled together
Accessories
Part No Description
TORAEA Tiger Tail Yellow & Black, 2.5 meter in length
35mm in diameter, Tested to 15kV
115
www.nesco.com.au
Telescopic Hot Sticks

Mainly used for the removal of Pole Service Fuses and Dropout fuses.
Features and Benefits

The triangular shape allows ease of use.
Rated at 100kV per foot.
The fluorescent tip section is highly visible and has a foam core.
Strong aluminium alloy head incorporates corona discharge and
includes a captive Belleville washer to hold universal attachments securely.
Ordering Information
Specifications
Part No Extended Length Retracted Length Weight Storage Case
(Nominal Meters) (Nominal Meters) Part No
HV-208 2.43 0.67 1.40 C-208
HV-212 3.80 1.48 1.66 C-30
HV-312 3.80 1.00 1.52 C-10

Catalogue No. HV-***
HV-216 5.00 1.53 2.26 C-30
HV-220 6.43 1.58 2.92 C-30
HV-225 7.80 1.63 3.68 C-40
HV-230 9.21 1.68 4.55 C-40
HV-235 10.06 1.72 5.50 C-40
HV-240 12.00 1.75 6.50 C-40 Catalogue No. 5455-10PTU
Accessories
Accessories
Part No Description
5455-10PTU Pig Tail Pole Fuse Extractor Head for use with
telescopic sticks
P10044 Disconnect hook for attachment to sunrise fitting
Catalogue No. P10044
11 6
Barrier Fencing Mesh
Re-usable, high durability barrier fencing Mesh.
UV resistant, high visibility.
Manufactured in different weights to suit applications.
Mesh is easy to erect and provides far greater levels of protection

than barrier tape
Features
Manufactured from polypropylene
UV stabilised Catalogue No. BMO
Bagged for protection/storage
Specifications
Colour Size Weight Part Number
Orange 1mtr x 50mtrs 8kg BMO1X50M
Green 1mtr x 50mtrs 8kg BMG1X50M
Note: Other colours available upon request
Underground Warning Tape

The most economical way of warning excavators of buried services below
ground. Our tapes can be printed with any text in any language, any colour
and any size, manufactured to your specifications. Standard texts are
available ex-stock.
Features
Material - High quality linear low density polyethylene.
Lead free pigments with virgin grade film.
Excellent chemical resistance.
Elongation - Machine direction 350% min - Transverse direction 300% min
Tensile Strength - Machine direction 20N/mm2 - Transverse direction
20N/mm (nominal)
Manufactured in accordance with AS/NZS 2648.1 1995 and AS/NZS 4275

Part O 1995.
Various thicknesses of polyethylene available.
Specifications
Text Colour Size Part Number
DANGER-BURIED ELECTRIC CABLE BELOW orange 150mm x 0.1mm x 500m UGWTE150500
DANGER-BURIED COMMUNICATION CABLE BELOW white 150mm x 0.1mm x 500m UGWTC150500
Other Texts available include Gas, Irrigation, Sewer, Water, Diesel & Fibre Optic.
Note: Other dimensions available upon request

117
NESCO
Electrical Products NESCO OVERVIEW
Brisbane Head Office
NESCO is an Importer, Exporter and Manufacturer

distributing throughout Australia and are now
recognised as one of Australias leading distributors
of electrical products.
NESCO specialise in Test and Measurement, Portable
Appliance Testing products, Domestic and Industrial
Heating, Overhead and Underground Power
Distribution products, Busway for industrial
applications and Industrial Automation Products.
NESCOs head office is in Brisbane with further
warehousing and representation in Townsville,
Rockhampton, Newcastle, Sydney, Melbourne,
Adelaide and Perth. This Coverage allows us to
service our customer base right throughout Australia
and is the main reason that NESCO is the choice of
many of the worlds Electrical Manufacturers when
seeking quality distribution in Australia.
NESCO Our marketing and distribution is primarily

Electrical Products directed through the wholesale distribution chains
Townsville with whom we have developed and maintain close
working relationships, providing both product
knowledge support and suitable product for their
end user customers.
In house training by our individual Product Managers
NESCO is available in our modern well equipped training room.
Electrical Products This facility is also available for private use by customers
New South Wales of Nesco.
NESCO is dedicated to the pursuit of the highest levels
of customer service and satisfaction, providing products
which meet the customers needs with knowledge and
back-up facilities to match.
NESCO
Electrical Products
Victoria
NESCO
Electrical Products
Western Australia
E & EO. All specifications are subject to change without

notice. Whilst every care has been taken in preparation,
we cannot be held responsible for typographical errors.
Queensland Sydney & NSW
Brisbane Head Office NESCO Electrical Products
NESCO Electrical Products Address 2/1-3 Whyalla Place, Prestons NSW, 2170
Address 54 Standish Street, Salisbury, QLD, 4107 Phone +61 2 9826 8088
Phone +61 7 3274 2466 FAX +61 2 9826 8188
FAX +61 7 3274 2970 E-mail [email protected]
E-mail [email protected]
Victoria
Townsville NESCO Electrical Products
NESCO Electrical Products Address 20 Laser Drive, Rowville, VIC, 3178
Address 47 Leyland Street, Garbutt, QLD, 4814 Phone +61 3 9294 1020
Phone +61 7 4762 7588 FAX +61 3 9294 1030
FAX +61 7 4775 6057 E-mail [email protected]
South Australia
Rockhampton NESCO Electrical Products
NESCO Electrical Products Phone 0427 167 919
Phone 0418 799 535 E-mail [email protected]
Western Australia
Northern NSW NESCO Electrical Products
Ross Joice Agencies Address 1-207 Banks St, Welshpool, WA, 6106
Address 109 Broadmeadow Rd, Phone +61 8 9229 8999
Broadmeadow, NSW, 2292 FAX +61 8 9355 1433
Phone +61 2 4961 4433 E-mail [email protected]
FAX +61 2 4961 2498

Catalogue

Uploaded by

Copyright:

Available Formats

Catalogue

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Catalogue

Uploaded by

Copyright:

Available Formats

NESCO ELECTRICAL PRODUCTS

Portable Appliance Testing Equipment

Research & Development

Product After Sales Backup & Service

TNT Series Testers

TNT Portable Appliance Tester

Specifications common to TNT and TNT+

TNT Portable Appliance Tester, with Carry Bag

TNT+ Portable Appliance Tester with RCD Test +

Common options for above

TNT ES-500 Earth Strap, 500mm long

TNT 3PADP 3 Phase Adaptor lead for TNT or TNT+

TNT EL Earth Lead with Croc Clip

TNT XL Extension Lead Adaptor (IEC - 3 Pin Plug)

TNT CAL Calibration Certificate for TNT

TNT+ CAL Calibration Certificate for TNT+

TNT-TTP Thermal transfer printer for printing test tags on site

TNT-PDAPACK H2210 Pocket PC, WinPATS CE, TNT-BCS Scanner, TNT-

WinPATS CE Testing and Recording Software for PocketPC (PDA)

WinPATS Lite Testing and Recording Software for Desktop/

TNT-CMPDA Interface Connector for TNT/TNT+ and PDA

TNT-CMPC Interface Connector for TNT/TNT+ and PC

1021-USB Barcode Scanner for USB port used with LAPTOP PC

Catalogue No. TNT-BCS

For complete specification see our website www.nesco.com.au

TESTING AND INSPECTION INTERVALS TABLE 4 NOTES:

2 Regulatory authorities, other Standards, workplace safety requirements or manufacturers

Standards for specific test intervals:

AS 1674.2 Safety in welding and allied processes - Electrical

AS/NZS 3002Electrical installations Shows and carnivals

AS/NZS 3004Electrical installations Marinas and pleasure craft at low voltage

AS/NZS 3012Electrical installations Construction and demolition sites

AS/NZS 4249Electrical safety practices Film, video and television sites

EXTRACT FROM AS/NZS 3760:2003

EXTRACT FROM AS/NZS 3760:2003

For complete specification see our website www.nesco.com.au

WAVECOM WinPATS CE / WinPATS lite

The TNT T and TNT+ introduced a new level of simplicity and

Simple steps are

1. Scan in barcode and appliance details

2. Plug appliance into to test, scan OK on the PDA and let

3. The test results are stored into the Pocket PC.

Once the days/weeks work is done synchronise the pocket PC

Complete packages including PDAs can be supplied, please contact

1021 SER Barcode Scanner

Using barcodes and integrating the safety testing process with an

Bar Code Tags

Appliance Failed Faulty Appliance Test Tags

PC in Office Office Printer

Laptop Test Tag Printer

Catalogue No. FAST Catalogue No. MP

RCDLB RCDTT TTCW

Catalogue No. TTCW-100 pack of 100

Custom Test Tags - see pages 11 & 12 for custom sheets

Catalogue No. TT/TTN-custom

Ap p lian ce Test Tag s

TA-2 Green April-June TN-2 Blue Feb/Jul

TA-3 Blue July -Sept TN-3 Orange Mar/Nov / /

TA-4 Yellow Oct-Dec TN-4 Green Apr/Aug OWNER

TA-6 White 6 Monthly July-Dec TN-6 Yellow Jun/Oct