4.

Attempt any two parts of the following : (102=20) Printed Pages4 EEC403
(a) Sketch the neat diagram of CRO. What is the utility of (Following Paper ID and Roll No. to be filled in your Answer Book)
delay line and trigger circuit. Which part of CRT is known PAPER ID : 0323 Roll No.
as electrostatic focusing system ? How the intensity to be
controlled ? What is normal pressure of CRT ? B. Tech.
(SEM. IV) THEORY EXAMINATION 2011-12
(b) Find out the fy/fx of the following Lissajous pattern.
ELECTRONIC INSTRUMENTATION AND
Assuming that 2 signal having frequencies fy and fx MEASUREMENTS
respectively applied on Y-Y and X-X deflection plates.
Time : 3 Hours Total Marks : 100
Note : (1) Attempt all questions.
(i) (ii)
(2) Assume the missing data if any.
(3) Marks are indicated at the end of each section.
(iii) (iv) 1. Attempt any four parts of the following : (54=20)
(a) What do you mean by instrumentation system ? Also
explain the functional block diagram of a measurement.
(v)
(b) Define fundamental and derived units. Derive the
relationship between electromagnetic system and
electrostatic system of the light velocity.
(c) Sketch circuit to show how ac voltmeter and ammeter (c) Energy stored in a parallel plate capacitor per unit volume
should be calibrated using standard instruments. Explain. (energy density) is given by w = kavbdc
permittivity of medium, d distance between plates
5. Attempt any two parts of the following : (102=20) v voltage between plates, k constant.
(a) Sketch a circuit to show how a potentiometer should be (d) Explain the limiting error in terms of true value. Two
used for calibrating a dc ammeter. Briefly explain. capacitors C1 = 150 2.4 F, C2 = 120 1.5 F connected
in parallel, what is the limiting error of the resultant
(b) Sketch the basic construction of a pen type galvanometer capacitance C ?
strip chart recorder. Briefly explain the instrument (e) Describe the principle of operation, advantages,
operation. disadvantages and application of PMMC.
(f) A PMMC instrument with FSD of 100 A and a coil
(c) Explain the basic principle of sweep generator. Also draw resistance of 1 k is to be converted into a voltmeter.
the block diagram of vertical amplifier. Determine the required multiplier resistance if the
voltmeter is to measure 50 V at full scale. Also calculate
the applied voltage when instrument indicates 0.8, 0.5 and
0.2 of FSD.
EEC403/PUR-40807(Re) 4 475 EEC403/PUR-40807(Re) 1 [Turn Over
2. Attempt any two parts of the following : (102=20) (d) Explain the sources of error in a Wheatstone bridge used
(a) Describe the emitter follower voltmeter. The simple to measure very low resistance. Discuss the range of
emitter follower voltmeter has VCC = 20 V, Rs + Rm = 9.3 k, resistance measurement with a Wheatstone bridge.
(e) A 4-terminal resistor with a nominal resistance of 0.025
Im = 1 mA at full scale and transistor hFE = 100.
is to be measured on a Kelvin Bridge as shown in figure.
(i) Calculate the meter current when E = 10 V. A 0.01 standard resistor is available. Determine the
(ii) Determine the voltmeter input resistance with and required ratio of R/P and r/p.
without the transistor. i1
i1
R
(b) Discuss the procedure for using the electronic voltmeter G
P 10
for ac measurement.

i2

+
i2
(c) Calculate the resistance scale marking at 25% and 75%
Four terminal p r Four terminal
of full scale for the series ohmmeter in given figure. resistor I I resistor
100 k
A Q S
I + i1 E
1 k
Eg (f) An op-amp voltmeter shown in figure, is required to
RX V Electronic
100 Voltmeter measure a maximum input of 20 mV. The op-amp input
1.5 V
current is 0.2 A and the meter circuit has Im = 100 A
10
FSD and Rm = 10 k. Determine suitable resistance value
for R3 and R4.
3. Attempt any four parts of the following : (54=20)
IB +VCC
(a) Describe the various methods of measurement of medium +
E
resistance.
(b) Describe the operation and phasor diagram of Schering VEE I4 R4 Vout
Bridge. IB
(c) Explain the converging balance equation of AC Bridge

R3
when impedances in its phase magnitude form.

EEC403/PUR-40807(Re) 2 EEC403/PUR-40807(Re) 3 [Turn Over