CA3260, CA3260A

Data Sheet December 10, 2009 FN1266.7

4MHz, BiMOS Operational Amplifier with Features

MOSFET Input/CMOS Output MOSFET Input Stage provides
CA3260A and CA3260 are integrated circuit operational - Very High ZI = 1.5T (1.5 x 1012) (Typ)
amplifiers that combine the advantage of both CMOS and - Very Low II . . . . . . . . . . . . 5pA (Typ) at 15V Operation
bipolar transistors on a monolithic chip. The CA3260 series . . . . . . . . . . . . . . . . . . . . . . 2pA (Typ) at 5V Operation
circuits are dual versions of the popular CA3160 series.
Ideal for Single Supply Applications
Gate protected P-Channel MOSFET (PMOS) transistors are
Common Mode Input Voltage Range Includes
used in the input circuit to provide very high input
Negative Supply Rail; Input Terminals Can be Swung 0.5V
impedance, very low input current, and exceptional speed
Below Negative Supply Rail
performance. The use of PMOS field effect transistors in the
input stage results in common mode input voltage capability CMOS Output Stage Permits Signal Swing to Either
down to 0.5V below the negative supply terminal, an (Or Both) Supply Rails
important attribute in single supply applications. Pb-Free Available (RoHS Compliant)
A complementary symmetry MOS (CMOS) transistor pair,
capable of swinging the output voltage to within 10mV of
Applications
either supply voltage terminal (at very high values of load Ground Referenced Single Supply Amplifiers
impedance), is employed as the output circuit.
Fast Sample-Hold Amplifiers
The CA3260 Series circuits operate at supply voltages Long Duration Timers/Monostables
ranging from 4V to 16V, or 2V to 8V when using split
supplies. The CA3260A offers superior input characteristics Ideal Interface with Digital CMOS
over those of the CA3260. High Input Impedance Wideband Amplifiers
Voltage Followers (e.g. Follower for Single Supply D/A
Ordering Information Converter)

PART PART TEMP. PKG.

Voltage Regulators (Permits Control of Output Voltage
NUMBER MARKING RANGE (C) PACKAGE DWG. # Down to 0V)

CA3260E CA3260E -55 to +125 8 Ld PDIP E8.3 Wien Bridge Oscillators

CA3260EZ CA3260EZ -55 to +125 8 Ld PDIP* E8.3 Voltage Controlled Oscillators

(Note) (Pb-free)
Photo Diode Sensor Amplifiers
CA3260AE CA3260AE -55 to +125 8 Ld PDIP E8.3

CA3260AEZ 3260AEZ -55 to +125 8 Ld PDIP* E8.3

Pinout
(Note) (Pb-free) CA3260, CA3260A
(8 LD PDIP)
*Pb-free PDIPs can be used for through hole wave solder
TOP VIEW
processing only. They are not intended for use in Reflow solder
processing applications.
NOTE: These Intersil Pb-free plastic packaged products employ
special Pb-free material sets, molding compounds/die attach OUTPUT (A) 1 8 V+
materials, and 100% matte tin plate plus anneal (e3 termination A
finish, which is RoHS compliant and compatible with both SnPb and INV. INPUT (A) 2 7 OUTPUT (B)
- +
Pb-free soldering operations). Intersil Pb-free products are MSL B
classified at Pb-free peak reflow temperatures that meet or exceed NON INV. INPUT (A) 3 6 INV. INPUT (B)
the Pb-free requirements of IPC/JEDEC J STD-020.
+ -
V- 4 5 NON INV. INPUT (B)

1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 1998, 2005, 2006, 2009. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
 CA3260, CA3260A

Absolute Maximum Ratings Thermal Information

DC Supply Voltage (V+ to V-) . . . . . . . . . . . . . . . . . . . . . . . . . . 16V Thermal Resistance (Typical, Note 2) JA (C/W) JC (C/W)
DC Input Voltage . . . . . . . . . . . . . . . . . . . . . . (V+ +8V) to (V- -0.5V) PDIP Package* . . . . . . . . . . . . . . . . . . 100 N/A
Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8V Maximum Junction Temperature (Plastic Package) . . . . . . . +150C
Input Terminal Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1mA Maximum Storage Temperature Range . . . . . . . . . -65C to +150C
Output Short Circuit Duration (Note 1). . . . . . . . . . . . . . . . Indefinite Pb-Free Reflow Profile. . . . . . . . . . . . . . . . . . . . . . . . .see link below
http://www.intersil.com/pbfree/Pb-FreeReflow.asp
Operating Conditions *Pb-free PDIPs can be used for through hole wave solder
Temperature Range . . . . . . . . . . . . . . . . . . . . . . . . -55C to +125C processing only. They are not intended for use in Reflow solder
processing applications.

CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and
result in failures not covered by warranty.

NOTES:
1. Short circuit may be applied to ground or to either supply.
2. JA is measured with the component mounted on an evaluation PC board in free air.

Electrical Specifications TA = +25C, Typical Values Intended Only for Design Guidance.
TYPICAL VALUES
PARAMETER SYMBOL TEST CONDITIONS CA3260A CA3260 UNITS
Input Resistance RI VS = 7.5V 1.5 1.5 T
Input Capacitance CI f = 1MHz, VS = 7.5V 4.3 4.3 pF
Unity Gain Crossover Frequency fT VS = 7.5V 4 4 MHz
Slew Rate SR VS = 7.5V 10 10 V/s
Transient Response Rise Time tr CL = 25pF, RL = 2k, AV = +1, 0.09 0.09 s
VS = 7.5V
Overshoot OS 10 10 %
Settling Time (to <0.1%, VIN = 4VP-P) tS CL = 25pF, RL = 2k, AV = +1, 1.8 1.8 s
VS = 7.5V
Input Offset Voltage VIO V+ = 5V, V- = 0V 2 6 mV
Input Offset Current IIO V+ = 5V, V- = 0V 0.1 0.1 pA
Input Current II V+ = 5V, V- = 0V 2 2 pA
Common Mode Rejection Ratio CMRR V+ = 5V, V- = 0V 70 60 dB
Large Signal Voltage Gain AOL VO = 4VP-P, RL = 20k, 100 100 kV/V
V+ = 5V, V- = 0V
100 100 dB
Common Mode Input Voltage Range VICR V+ = 5V, V- = 0V 0 to 2.5 0 to 2.5 V
Supply Current I+ VO = 5V, RL = , V+ = 5V, V- = 0V 1 1 mA
VO = 2.5V, RL = , V+ = 5V, V- = 0V 1.2 1.2 mA
Power Supply Rejection Ratio PSRR VIO/V+, V+ = 5V, V- = 0V 200 200 V/V

Electrical Specifications For Each Amplifier at TA = +25C, V+ = 15V, V- = 0V, Unless Otherwise Specified.
CA3260A CA3260
TEST
PARAMETER SYMBOL CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
Input Offset Voltage |VIO| VS = 7.5V - 2 5 - 6 15 mV
Input Offset Current |IIO| VS = 7.5V - 0.5 20 - 0.5 30 pA
Input Current II VS = 7.5V - 5 30 - 5 50 pA
Large Signal Voltage Gain AOL VO = 10VP-P, 50 320 - 50 320 - kV/V
RL = 10k
94 110 - 94 110 - dB
Common Mode Rejection Ratio CMRR 80 95 - 70 90 - dB

2 FN1266.7
December 10, 2009
 CA3260, CA3260A

Electrical Specifications For Each Amplifier at TA = +25C, V+ = 15V, V- = 0V, Unless Otherwise Specified. (Continued)
CA3260A CA3260
TEST
PARAMETER SYMBOL CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
Common Mode Input Voltage VlCR 0 -0.5 to 10 0 -0.5 to 10 V
Range 12 12
Power Supply Rejection Ratio PSRR VIO/V+ - 32 150 - 32 320 V/V
V+ = 17.5V
Maximum Output Voltage VOM+ RL = 10k 11 13.3 - 11 13.3 - V
VOM- - 0.002 0.01 - 0.002 0.01 V
VOM+ RL = 14.99 15 - 14.99 15 - V
VOM- - 0 0.01 - 0 0.01 V
Maximum Output Current IOM+ Source VO = 0V 12 22 45 12 22 45 mA
IOM- Sink VO = 15V 12 20 45 12 20 45 mA
Total Supply Current I+ RL =
VO (Amplifier A) = 7.5V - 9 15.5 - 9 15.5 mA
VO (Amplifier B) = 7.5V
VO (Amplifier A) = 0V - 1.2 3 - 1.2 3 mA
VO (Amplifier B) = 0V
VO (Amplifier A) = 0V - 5 8.5 - 5 8.5 mA
VO (Amplifier B) = 7.5V
Input Offset Voltage VIO/T - 6 - - 8 - V/C
Temperature Drift
Crosstalk f = 1kHz - 120 - - 120 - dB

Schematic Diagram
8 V+

AMPLIFIER A AMPLIFIER B

Q6 Q7 Q21 Q20
Q11
Q10 Q25
Q9 Q23
D2 D3 D6 D7 Q24

D1 D4 D5 D8
R5 R12
2K 2k
Q1 Q2 Q8 Q22 Q16
Q12 C1 C2 Q15 Q26
R4 30pF 30pF R11
Q14 Q13 R3 1k 1k R10 Q27 Q28
1k Q5 Q19 1k

R6 R7 Q3 Q4 Q18 Q17 R14 R13

200k 300k 300 200k
R1 R2 R9 R8
1k 1k 1k 1k

3 2 1 7 6 5 4

3 FN1266.7
December 10, 2009
 CA3260, CA3260A

Dual-In-Line Plastic Packages (PDIP)

N
E8.3 (JEDEC MS-001-BA ISSUE D)
8 LEAD DUAL-IN-LINE PLASTIC PACKAGE
E1
INDEX INCHES MILLIMETERS
AREA 1 2 3 N/2
SYMBOL MIN MAX MIN MAX NOTES
-B-
A - 0.210 - 5.33 4
-A-
D E A1 0.015 - 0.39 - 4
BASE A2 0.115 0.195 2.93 4.95 -
PLANE A2
-C- A
SEATING
B 0.014 0.022 0.356 0.558 -
PLANE L C B1 0.045 0.070 1.15 1.77 8, 10
L
D1 A1 eA C 0.008 0.014 0.204 0.355 -
D1
B1 e D 0.355 0.400 9.01 10.16 5
eC C
B
eB D1 0.005 - 0.13 - 5
0.010 (0.25) M C A B S
E 0.300 0.325 7.62 8.25 6
NOTES: E1 0.240 0.280 6.10 7.11 5
1. Controlling Dimensions: INCH. In case of conflict between
e 0.100 BSC 2.54 BSC -
English and Metric dimensions, the inch dimensions control.
2. Dimensioning and tolerancing per ANSI Y14.5M-1982. eA 0.300 BSC 7.62 BSC 6
3. Symbols are defined in the MO Series Symbol List in Section eB - 0.430 - 10.92 7
2.2 of Publication No. 95. L 0.115 0.150 2.93 3.81 4
4. Dimensions A, A1 and L are measured with the package seated
N 8 8 9
in JEDEC seating plane gauge GS-3.
5. D, D1, and E1 dimensions do not include mold flash or Rev. 0 12/93
protrusions. Mold flash or protrusions shall not exceed 0.010
inch (0.25mm).
6. E and eA are measured with the leads constrained to be
perpendicular to datum -C- .
7. eB and eC are measured at the lead tips with the leads
unconstrained. eC must be zero or greater.
8. B1 maximum dimensions do not include dambar protrusions.
Dambar protrusions shall not exceed 0.010 inch (0.25mm).
9. N is the maximum number of terminal positions.
10. Corner leads (1, N, N/2 and N/2 + 1) for E8.3, E16.3, E18.3,
E28.3, E42.6 will have a B1 dimension of 0.030 - 0.045 inch
(0.76 - 1.14mm).

All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporations quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.

For information regarding Intersil Corporation and its products, see www.intersil.com

4 FN1266.7
December 10, 2009