1 - 201 - Steam and Water Drums

Steam drum
In the early designs the drums were riveted or solid forged from a single
ingot, but for modern boilers the drum is generally fabricated from steel
plate of differing thicknesses and welded. The materials used are
governed by classification society rules. Test pieces must be provided.
The cylindrical drum is normally constructed from four plates.
Two dished End plates, a thick wall tube plate (thicker to accommodate
the holes drilled in it without increased stress) and completed with a
thinner wrapper plate.
Construction takes the form of rigidly clamping the descaled,
bent wrapper and tube plates together. In addition test pieces cut from
the original material are attached to the construction in such away that
the longitudinal weld extends either sided of the join. These pieces are
later removed and shaped test shapes cut out from specified areas
including across the weld.
The longitudinal weld is critical (taking twice the
circumferential stress) and is normally carried out by specialized
automatic machinery using submerged arc techniques.
The dished end pieces are accurately aligned and welded.
On completion the construction is cleaned and non-destructive
testing- such as x-ray photography, carried out. Final machining is
carried out and any stub pieces and doublers attached. The now
complete drum is heat treated at 600 to 650'C.
The final process is hydraulic testing to classification
requirements. Natural circulation within a boiler is due to the differing
specific gravities of the water at the differing temperatures, the steam
drum provides a reservoir of cool water to give the gravitational head
necessary for natural circulation. Cool water entering the steam drum
via the feed lines provides the motive effect for the circulation
distributing it to the downcomers.
Also the space within the drum provides for the separation of
the steam and water emulsions formed in the water walls and the
generating tubes. Water droplets entrained with the separated steam are
removed by separating components fitted in the drum as well as the

perforated baffle plates fitted at the water line.
The space above the water line provides for a reserve steam
space needed to maintain plant stability during manoeuvring conditions.
Also fitted are the chemical injection distributing pipe and the
scuming plate.
The smaller the drum is made, the less thickness of material
that is required. However, the limitation to how small is that sufficient
space must be allowed for the separation of water from the steam before
passing out to the superheater space otherwise dryers must be used.
Also, due to the smaller reserve of water, larger fluctuations in water level
occur during manoeuvring.
SAFETY VALVE CONFIGURATION
Figure 1
The internal fittings in the steam drum help distribute the water evenly
throughout the drum, separate the generated steam from the water and
remove moisture from the steam before it leaves the boiler (refer to Figure
2).
1. Lower baffle plates or apron plates Separate the incoming

feedwater and generated steam and direct the steam to the
separators.
2. Primary separators (cyclone separators) separate most of the water
from the steam by giving it a cyclone or rotary motion so that the
water particles are expelled from the steam by the centrifugal
forces. These separators are vertically mounted in the steam drum
so that the steam rises out the top and the water falls back into
the steam drum.
3. Secondary separators (chevron dryers) remove additional moisture
from the steam by changing the direction of steam flow several
times. The steam passes on but the moisture cannot make the
direction change with the steam. These separators are mounted
above the primary separators and direct steam to the dry box
which collects the steam at the top of the steam drum, directing it
to the steam outlet piping to the superheater.
4. Feedwater leaves the economizer and enters the boiler through the
internal feed pipe and becomes "boiler water." Perforations along
the side of the feed pipe allow water to be distributed evenly
throughout the steam drum (refer to Figure 2)
STEAM DRUM INTERNALS
Figure 2
5. Since suspended solids may accumulate on the surface of the

water in the steam drum, there must be means of removing them.
The surface blow pipe is used to remove these light suspended
solids from the surface of the water and to reduce the total
dissolved solid content of the boiler water. Suspended solids
usually consist of oil, salt contaminants, or excessive treatment
chemicals which can cause foaming on the water surface.
Dissolved solids usually consist of salt contaminants and
treatment chemicals that are in solution.
Water drum
Distributes feed water from the downcomers to the headers and
generating tubes. Provides a space for accumulating precipitates and
allows them to be blown down.
Water drum size is limited to that required to receive the
generating tubes, for modern radiant heat boilers with only a single bank
of screen tubes and no generating tubes between the drums, the water
drum has been replaced by a header and the downcomers fed straight to
the waterwall headers. With system blow down is done at the steam
drum. Too small a water drum can cause problems of maintaining ideal
water level and little steam reserve

1 - 201 - Steam and Water Drums

Uploaded by

Copyright:

Available Formats

1 - 201 - Steam and Water Drums

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

1 - 201 - Steam and Water Drums

Uploaded by

Copyright:

Available Formats

Steam drum

removed by separating components fitted in the drum as well as the

1. Lower baffle plates or apron plates Separate the incoming

STEAM DRUM INTERNALS

5. Since suspended solids may accumulate on the surface of the

You might also like