Rucksack Backpack Instructions Pattern

featuring fabrics from:
E ADS
HR
Rucksack
Sew
rlu s
e
d
W an
T he
Togethe
g
r
n
TH O NE T
R
Coyote
Thank you for choosing to sew along with us!

We always have a great time Sewing Together at Hawthorne
Threads and were so glad youve decided to join the fun. For us
its a wonderful way for our staff to connect with the fabric and,
for some, to learn a lifelong skill while on the job. We endeavor
to choose projects suitable for many skill levels so grab a friend
or family member and get ready to sew together!
--WHAT YOULL NEED-A
Fabrics of your choice
SCISSORS
RULER
PINS
IRON+BOARD
(Were using
Coyote)
TOOLS
C
D
Thread
Y A R D A G E
N E E D E D
From pre-washed fabrics:
Fusible
fleece
Lightweight
woven fusible
interfacing
Fusible
Peltex
Two 1
strap slides
Four
buttons
FABRIC A 1 yard
FABRIC B yard
FABRIC C 1 yard
FABRIC D 1 yard
7 zipper
(or cut to size)
INTERFACING 1 yard
FLEECE yard
PELTEX yard
--DIMENSIONS-3
2
2
28
15
29
SHELL
cut: 2 fabric A
+ 2 interfacing
LINING
cut 1 fabric C
28
29
BASE
SUPPORT
4
12
POCKET
cut: 1 fabric B
1 fabric D
BASE
cut 1 fabric D
F
R
O
N
T
29
cut 3
from
Peltex
10
10
BASE
SUPPORT
COVER
cut 1
fabric B
S
T
R
A
P
S
T
R
A
P
cut 2 fabric D
S
H
O
U
L
D
E
R
44
S
T
R
A
P
cut 2 fabric D
+ 2 interfacing
12 x 2
12
7
HANDLE
cut: 1 fabric D
1 fusible fleece
FINISHED PIECE
B
A
C
K
4
2
cut: 2 fabric D
2 fusible fleece
STRAP STAY
cut 4 fabric D
Cut pieces from fabric, fusible interfacing, fleece, and Peltex.

You should have:
2 exterior shell pieces

+ interfacing
1 lining piece
1 pocket exterior
1 pocket lining
1 base piece
2 front straps
2 back straps
+ interfacing
2 shoulder straps
+ fusible fleece
1 handle piece
+ fusible fleece
4 strap stays
3 Peltex base support pieces
1 base support cover
Iron on interfacing and
fusible fleece to exterior,
straps, and handle.
Trim ends from
fusible fleece pieces:
from each end of handle

1 from top end, 2 from bottom
end of both shoulder straps
Prep front and back straps:

Press front and back straps in on each side so
that edges meet in the middle, right side out.
Straps should be 1 wide.
Fold one
end of each
back strap onto
itself at interfacing
edge 12 from end
+ press.
Edgestitch the sandwiched

section of the strap together
from edge of fabric.
Sew a buttonhole centered
from the end of the sandwiched strap.
Prep shoulder straps, strap stays, and handle piece:

First turn one side in legthwise (skip this on the strap stays.)
Then, fold into thirds + press, covering the raw edge and
centering the turned edge on top.
Using a wide zigzag stitch, sew down the
center securing the turned edge at the back.
Slide a strap slide over the bottom
end of the shoulder strap (the one
with 2 of fleece trimmed.)
Fold the edge over and create
a loop by pinning it back onto the
strap + sew down.
On the top edge of the pocket exterior
piece, find center point + mark.
Use
Trim
Measure 3 out from either
seams.
zipper if
side of center + mark.
needed!
Center zipper about
Using zipper foot,
Sew shell pieces
below these marks + pin.
baste on zipper,
together at side seam,
then sew pocket
right sides together.
exterior to pocket
Press
lining, right sides
seam
together.
open.
Turn + press flat so that zipper sticks up from the top edge.
Topstitch pocket hem and from edge.
Align bottom edges

of pocket and shell.
Mark where top
edge of the zipper
teeth fall on shell.
Flip pocket up and

align the corners
of the zipper tape
to the placement
marks. Pin + sew.
Flip pocket back over, again lining it up with the
bottom edge of shell.
Press flat + baste
together along bottom
edge just inside seam
allowance at
Place the shell right-side-up on your workspace.

Along both the top and
bottom edges, measure
3 and then 10 out
from either side of the
side seam + mark.
F
R
O
N
T
B
A
3 C
K
10
Find your prepared front

straps and position them
vertically, centered over
the lefthand placement
marks. Pin down securely.
F
R
O
N
T
B
A
C
K
Make sure the free end of the zipper is folding downward

toward the pocket hem, so that the teeth just about meet.
Next, position back
straps vertically,
centered over righthand
placement marks + pin.
F
R
O
N
T
B
A
C
K
Edgestitch
down from
strap edges,
enclosing the end of the
zipper under the strap.
Edgestitch down like you

did the front straps, but this
time, when you reach where
the strap is folded and
sewn, continue past the raw
edge about then stop.
With the needle still in the fabric,
turn and sew perpendicularly
across strap and
continue sewing
a box stitch over
the section
where the strap
is doubled up.
Continue down
opposite side of
the strap to
complete.
Use
hand wheel
when sewing
over zipper!
Mark 1 and 8 up from top of pocket on either side

of the front straps.
F
R
O
N
T
Turn all of the

strap stay ends
under + press.
Position parallel
to pocket hem
with turned
edges on either
side of the straps
and centered
over the
placement
marks, pin.
B
A
C
K
Sew down turned

edges with box
stitches, the stays
should bubble up a
bit from the shell.
7
Position shell
right-side-up,
measure +
mark 3 up
from bottom.
Sew on buttons 2 below

the top stays and 4 below
the bottom stays, centered
on top of the front straps.
Layer base
piece onto shell
right-side-down
with its bottom
edge aligned
with the
placement
marks.
Sew down
from edge.
Fold piece over at this seam + press flat.

Bottom edges of shell, pocket, and base should all be aligned. Baste together all
bottom edges.
Trim the bulk from the
seam allowance at
bottom edge of shell
Edgestitch along folded edge to secure.
and pocket, keeping
base piece in tact.

14
Again, begin with shell right-side-up.

Measure and mark strap and handle
placement up from top edge of base
on the back side of the shell using the
specifications shown here.
Also mark placement guides
along the inner sides of each
strap at 2 from the edge of the
strap slide end.
Facing right-side-down,
bend handle as shown and
line up each outer corner
with the placement marks
14 above base top edge.
Let the ends angle evenly
toward the shoulder strap
placememt marks below.
Pin + tack in place.
Position strap right-side-down so that the guide on the strap touches the placement
mark on the shell. Angle the strap so that it lines up with the end of the handle + pin.
Edgestitch around strap edge, sewing a box
stitch in the overlap at the handle to secure.
Feed the long upper end of

shoulder strap through the
strap slide, turn end under
then again at the edge of the
fleece + sew with a box stitch.
Line up seam
allowances of
shell + pin.
Base and pocket
edges should
match up.
Tuck straps and handle in
as far as you can so that
you dont accidentally
trap one in your seam.
Sew up seam
+ press open.
Trim seam allowance from
pocket and base pieces to
about to remove some bulk
from the seam.
Next, flatten the bag at the seams

and pin along the bottom edge.
Sew + press towards the back.
To box the corners, flatten the base

and center the bottom seam. Mark 3
from the corners along each side.
Connect the marks to section off
each corner.
Pin + sew across the guidelines.

OPTIONAL: Add any pockets
you would like to the lining
now. Remember, the top will
roll down, keep pockets
below 10 from top of lining.
Complete the lining in the

same basic way as the shell,
sew up side and bottom
seams and box the corners,
seam pressed toward front.
Turn shell so that the right

side is facing out and the
lining so that the wrong
side is facing out.
Tuck lining into the shell,
wrong sides together.
Align corners at the base.
The remaining raw edge will be
sewn with a flat-felled seam.
10
Heres how!
First, line up side seams, center lines, and top
edges of shell and lining + pin.
From the right side, topstitch around edge using a
1 seam allowance, easing the shell in slightly.
Flat-felled
seams are most
often used on
side seams, ours
is modified slightly
to complete the
top hem.
Trim away about half of the

seam allowance of lining only.
Fold seam allowance of shell down

over the seam allowance of the lining
so that it meets the seam line + press.
Then, fold over once more so that the raw
edges are covered and you can see the
seam on the inside of the bag. Press + pin.
From the outside of the bag,

topstitch along
folded top edge
at + press.
11
For a sturdy bottom, fuse the three pieces of Peltex together.

Fold the base support cover piece in half,
right sides together.
Sew along two of the three open edges at
, leaving one of the shorter ends open.
Turn right-side-out and press seams flat.
Slide the three layers of
Peltex into the pouch.
Turn the loose seam
allowance in, press, and
sew up the opening.
Tuck completed base support into the bottom of your bag
+ roll it up!
CONGRATULATIONS!
YOUVE FINISHED YOUR RUCKSACK!

Share it with us on our Facebook page or
Instagram using #HTSEWINGTOGETHER
hawthornethreads.com
follow us

Rucksack Backpack Instructions Pattern

Uploaded by

Copyright:

Available Formats

Rucksack Backpack Instructions Pattern

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Rucksack Backpack Instructions Pattern

Uploaded by

Copyright:

Available Formats

featuring fabrics from:

Thank you for choosing to sew along with us!

--WHAT YOULL NEED-A

Fabrics of your choice

Cut pieces from fabric, fusible interfacing, fleece, and Peltex.

2 exterior shell pieces

from each end of handle

Prep front and back straps:

Edgestitch the sandwiched

Prep shoulder straps, strap stays, and handle piece:

Align bottom edges

Flip pocket up and

Place the shell right-side-up on your workspace.

Find your prepared front

Make sure the free end of the zipper is folding downward

Edgestitch down like you

Mark 1 and 8 up from top of pocket on either side

Turn all of the

Sew down turned

Sew on buttons 2 below

Fold piece over at this seam + press flat.

Again, begin with shell right-side-up.

Feed the long upper end of

Next, flatten the bag at the seams

To box the corners, flatten the base

Pin + sew across the guidelines.

Complete the lining in the

Turn shell so that the right

Trim away about half of the

Fold seam allowance of shell down

From the outside of the bag,

For a sturdy bottom, fuse the three pieces of Peltex together.

YOUVE FINISHED YOUR RUCKSACK!

You might also like