Scribd
Upload
1K views4 pages

Native VLAN Mismatch Error On Access Port

VLAN Native

Uploaded by

Miguel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
1K views4 pages

Native VLAN Mismatch Error On Access Port

VLAN Native

Uploaded by

Miguel
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as DOCX, PDF, TXT or read online on Scribd
You are on page 1/ 4

Native VLAN mismatch Error on Access Port

Cisco switches always have VLAN 1 as


the default VLAN, which is needed for many protocol communication between switches
like spanning-tree protocol for instance. Unfortunately you cant change or even delete the
default VLAN, it is mandatory.
The native VLAN is the only VLAN which is not tagged in a trunk, in other words, native
VLAN frames are transmitted unchanged.
Per default the native VLAN is VLAN 1 but you can change that.

#show interface Fa0/8 trunk


Port

Mode

Encapsulation

Status

Native vlan

Fa0/8

on

802.1q

other

To change it use the following command: switchport trunk native vlan <vlan number>
(config-if)#switchport trunk native vlan 2
(config-if)#do show interface f0/8 trunk
Port

Mode

Encapsulation

Status

Native vlan

Fa0/8

on

802.1q

other

The default VLAN is still VLAN 1.


#show vlan id 1
VLAN Name Status

Ports

- -

1 default active

Fa0/8, Gi0/1

I am having two switches connected by access port but with two different vlan at both end. On
both ends I got following Native VLAN mismatch discovered errors.

SW1# sh log

Aug

5 15:16:35.286: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:17:33.992: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:18:32.149: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:19:28.217: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:20:24.622: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:21:17.736: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:22:10.554: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:23:01.778: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


Aug

5 15:24:00.581: %CDP-4-NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered

on GigabitEthernet1/39 (14), with SW2 GigabitEthernet0/1/0 (2).


SW1#

SW1#show cdp nei det | b SW2


Device ID: SW2
Entry address(es):
IP address: 172.18.14.11
Platform: cisco ISR4331/K9,

Capabilities: Router Switch IGMP

Interface: GigabitEthernet1/39,
Holdtime : 151 sec

Port ID (outgoing port): GigabitEthernet0/1/0

Version :
Cisco

IOS

Software,

ISR

Software

(X86_64_LINUX_IOSD-UNIVERSALK9-M),

Version

15.6(1)S1, RELEASE SOFTWARE (fc3)


Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2016 by Cisco Systems, Inc.
Compiled Wed 09-Mar-16 18:32 by mcpre
advertisement version: 2
VTP Management Domain: ''
Native VLAN: 2 (Mismatch)
Duplex: full
Power Available TLV:
Power request id: 0, Power management id: 1, Power available: 0, Power
management level: -1
Management address(es):
IP address: 172.18.14.11
SW1#

The Configuration on the ports at both ends:

SW1(config-if)#do sh run int g1/39


Building configuration...
Current configuration : 133 bytes
!
interface GigabitEthernet1/39
description SW2 G0/1/0
switchport access vlan 14
switchport mode access
end
SW1#

SW2#sh run int g0/1/0


interface GigabitEthernet0/1/0

description MS-Network-MGMT
switchport access vlan 2
spanning-tree portfast
SW2#show cdp nei det

Device ID: SW1


Entry address(es):
IP address: 172.18.14.3
Platform: cisco WS-C4510R+E,

Capabilities: Router Switch IGMP

Interface: GigabitEthernet0/1/0,

Port ID (outgoing port): GigabitEthernet1/39

Holdtime : 121 sec


SW2#

In circumstances like this, where you are sure the mismatch is not a real problem, you may
consider to disable cdp for those interfaces to shut up those noise information.

SW2#show run int g1/39


Building configuration...
Current configuration : 148 bytes
!
interface GigabitEthernet1/39
description SW2 G0/1/0
switchport access vlan 14
switchport mode access
no cdp enable
end
SW2#

You might also like