HCDA (Dumps)

item 1.1.1.
1
cardinality = multiple
minnumber = 2
maxnumber = 2
correct-response = "A,B"
presentation [
<image uri="1-1-1-1.JPG">
Refer to the graphic. The network administrator wants to improve the performance of
network transmission, what steps can the administrator take? (Two Answers)
<choice ident=A> Change the work mode to full duplex of each end station.
<choice ident=B> Link the end stations together using a switch.
<choice ident=C> Change the work mode to half duplex of each end station.
<choice ident=D> Link the end stations together using a hub.
]
item 1.1.1.2
correct-response = "cd"
minnumber = 2
maxnumber = 2
presentation [
On Huawei switch, which of the following commands can be used to set port duplex
mode as"auto negotiation"? (Select 2 Answers)
<choice ident="A">duplex negotiation auto
<choice ident="B">duplex auto-negotiation
<choice ident="C">duplex auto
<choice ident="D">undo duplex
]
item 1.1.1.3
cardinality = single
correct-response = "B"
presentation [
The network administrator wishes to transmit data between two end stations. The
network interface cards of both devices operates at 100Mbps however one supports
half duplex while the other uses full duplex mode. What will occur as a result?
<choice ident=A> The end stations cannot communicate.
<choice ident=B> The end stations can communicate, but data may be lost during
transmission of large amounts of traffic.
<choice ident=C> The end stations will operate normally.
<choice ident=D> The end stations can communicate, but speed is different during
transmission of large amounts of traffic.
]
item 1.1.2.1
correct-response = "a"
presentation [
An Ethernet port can work one of three duplex modes, whereas an Optical Ethernet
port only supports one single mode. Which of the following represents this mode?
<choice ident="A">Full-duplex
2017-1-24
1 , 91
<choice ident="B">Half-duplex
<choice ident="C">Auto-negotiation
<choice ident="D">Simplex
]
item 1.2.1.1
correct-response = " C"
presentation [
While inspecting packets in the network, a network administrator discovers a frame
with the destination MAC address of 01-00-5E-A0-B1-C3. What can the administrator
determine from this?
<choice ident=A> The MAC address is a unicast address.
<choice ident=B> The MAC address is a broadcast address
<choice ident=C> The MAC address is a multicast address.
<choice ident=D> The MAC address is incorrect.
]
item 1.2.1.2
correct-response = "d"
presentation [
According to OSI reference model, which layer is responsible for end to end error
checking and flow control?
<choice ident="A">Physical layer
<choice ident="B">Data link layer
<choice ident="C">Network layer
<choice ident="D">Transport layer
]
item 1.2.2.1
correct-response = "bcd"
minnumber = 3
maxnumber = 3
presentation [
Which of the following mechanisms are used for flow control? (Select 3 Answers)
<choice ident="A">Acknowledgement
<choice ident="B">Buffering
<choice ident="C">Source quench messages
<choice ident="D">Windowing
]
item 1.2.2.2
presentation [
Source Destination Protocol Info
10.0.12.1 10.0.12.2 TCP
50190 > telnet [SYN] Seq=0 Win=8192 Len=0
MSS=1460
10.0.12.2 10.0.12.1 TCP
telnet> 50190 [SYN, ACK] Seq=0 Ack=1
Win=8192 Len=0 MSS=1460
2017-1-24
2 , 91
10.0.12.1 10.0.12.2 TCP

50190 > telnet [ACK] Seq=1 Ack=1 Win=8192
Len=0
Refer to the capture output.The administrator has captured three packets in the
network. Which statement regarding the capured packets is incorrect?
<choice ident=A>This packets represent a TCP three-way handshake process.
<choice ident=B>10.0.12.1 is the telnet server, while 10.0.12.2 is the telnet client.
<choice ident=C>The three packets contain no application data.
<choice ident=D>10.0.12.1 uses port 50190 to buid the telnet connection.
]
item 1.2.2.3
correct-response = "A,C"
minnumber = 2
maxnumber = 2
presentation [
When a network administrator configures STP in the network, BPDU begin to be sent
by switch. Which of the following statements regarding the BPDU frame are correct?
(Two Answers)
<choice ident=A> A BPDU uses the IEEE 802.3 standard frame type.
<choice ident=B> A BPDU uses the Ethernet II standard frame type.
<choice ident=C> The BPDU frames control field is 3.
<choice ident=D> The destination MAC address field of a BPDU frame contains a
broadcast MAC address.
]
item 1.2.3.1
correct-response = "ac"
minnumber = 2
maxnumber = 2
presentation [
An Ethernet frame is captured by network protocol analyzer tool and the value of
Type/Length field is 0x0800. Which of the following statements about the frame are
correct? (Select 2 Answers)
<choice ident="A">The frame structure of the frame is Ethernet_II
<choice ident="B">The frame structure of the frame is 802.3
<choice ident="C">Its upper layer protocol is IP
<choice ident="D">Its upper layer protocol is IPX
]
item 1.3.1.1
presentation [
Refer to the graphic. Which of the following IP addresses can be assigned to the
host?
<choice ident=A> 20.1.1.93
<choice ident=B> 20.1.1.123
<choice ident=C> 20.1.1.128
<choice ident=D> 20.1.1.136
2017-1-24
3 , 91
]
item 1.3.1.2
presentation [
Which of the following subnet masks is more appropriate for point-to-point links?
<choice ident="A">255.255.255.224
<choice ident="B">255.255.255.240
<choice ident="C">255.255.255.248
<choice ident="D">255.255.255.252
]
item 1.3.1.3
minnumber = 2
maxnumber = 2
presentation [
Which of the following route entries can be aggregated into 10.0.0.24/29? (Select 2
Answers)
<choice ident="A">10.0.0.25/30
<choice ident="B">10.0.0.23/30
<choice ident="C">10.0.0.26/30
<choice ident="D">10.0.0.22/30
]
item 1.3.1.4
correct-response = "b"
presentation [
The host address 191.10.96.132 has been assigned along with the default mask in
the network. Which of the following represents the network address that corresponds
to this host address?
<choice ident="A">191.0.0.0
<choice ident="B">191.10.0.0
<choice ident="C">191.10.48.0
<choice ident="D">191.10.96.0
]
item 1.3.1.5
presentation [
The host address 192.168.1.7 has been assigned along with the default mask in the
network. Which of the following represents the network address that corresponds to
this host address?
]
2017-1-24
4 , 91
item 1.3.1.6
correct-response = "C"
presentation [
Which of the following descriptions regarding the TTL field of the IP packet is correct?
<choice ident=A> The TTL defines how many packets the source can send.
<choice ident=B> The TTL defines the duration during which the source can send
packets.
<choice ident=C> The TTL value will decrement by 1 each time the packet is
routed.
<choice ident=D> The TTL value will increment by 1 each time the packet is routed.
]
item 1.3.2.1
correct-response = "bc"
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements are correct about TTL field in IP packet? (Select 2
Answers)
<choice ident="A">The maximum value of TTL is 65535
<choice ident="B">Normally, it's impossible for a router to receive a packet whose
TTL is zero.
<choice ident="C">The main purpose of TTL is to prevent IP packets from circulating
endlessly in a network which can consume a lot of bandwidth
<choice ident="D">TTL value will be decremented as a packet is passed through the
network devices such as hub, LAN switch and router.
]
item 1.3.2.2
presentation [
Which of the following is a valid IP host address?
<choice ident="B">1.255.255.2/24
<choice ident="D">192.240.150.255/24
]
item 1.3.2.3
presentation [
The IP address 192.168.1.127/25 represents a ( ) address.
<choice ident="A">Host
<choice ident="B">Network
<choice ident="C">Multicast
<choice ident="D">Broadcast
]
2017-1-24
5 , 91
item 1.3.2.4
minnumber = 2
maxnumber = 2
presentation [
150.25.0.0 is a network segment and its mask is 255.255.224.0. Which of the
following are valid host addresses? (Select 2 Answers)
]
item 1.3.2.5
correct-response = "ad"
minnumber = 2
maxnumber = 2
presentation [
If the network mask is 255.255.240.0, which of the following are valid network
address? (Select 2 Answers)
]
item 1.3.2.6
correct-response = "c"
presentation [
Which of the following is the numerically largest IP host address for a subnet address
5.32.0.0 with mask 255.224.0.0?
]
item 1.3.2.7
presentation [
If the mask of a network is 255.255.248.0, then which of the following belongs to the
same network segment?
<choice ident="A">10.110.16.1 and 10.110.25.1
<choice ident="B">10.76.129.21 and 10.76.137.1
<choice ident="C">10.52.57.34 and 10.52.62.2
<choice ident="D">10.33.23.2 and 10.33.31.1
]
2017-1-24
6 , 91
item 1.3.2.8
presentation [
Thirty-two subnets are expected to be available within a class C address segment,
which of the following is the most appropriate subnet mask?
<choice ident="A">255.255.255.252
<choice ident="B">255.255.255.240
<choice ident="C">255.255.255.255
<choice ident="D">255.255.255.248
]
item 1.3.2.9
presentation [
A network administrator wishes to assign an IP address to a router interface. Which
of the following IP addresses can be assigned?
<choice ident=A> 192.168.10.112/30
<choice ident=B> 237.6.1.2/24
<choice ident=C> 145.4.2.55/26
<choice ident=D> 127.3.1.4/28
]
item 1.3.2.10
correct-response = "D"
presentation [
A network administrator has been assigned the IP address segment
192.168.176.0/25, from which he/she must allocate a subnet to support 20 users in
the marketing department. Which IP subnet best supports this requirement?
<choice ident=A>192.168.176.0/25
<choice ident=B>192.168.176.0/30
<choice ident=C>192.168.176.48/29
<choice ident=D>192.168.176.96/27
]
item 1.3.3.1
presentation [
A company applies for a class C IP address for subnetting, it has eight branches.
Each branch has a subnet and should support at least 14 hosts. What would be an
appropriate subnet mask?
<choice ident="A">255.255.255.0
<choice ident="B">255.255.255.128
<choice ident="C">255.255.255.192
<choice ident="D">255.255.255.224
]
item 1.3.3.2
2017-1-24
7 , 91
presentation [
A company applies for a class C IP address for subnetting. It has six branches and
the largest branch should have 26 hosts. What would be an appropriate subnet
mask?
<choice ident="A">255.255.255.0
<choice ident="B">255.255.255.128
<choice ident="C">255.255.255.192
<choice ident="D">255.255.255.224
]
item 1.4.1.1
presentation [
In the case of Huawei router, what is the "-i" parameter in a Ping command issued on
a VRP operating system used to set?
<choice ident="A">Interface for sending an Echo Request packet
<choice ident="B">Source IP address for sending an Echo Request packet
<choice ident="C">Interface for receiving an Echo Reply packet
<choice ident="D">Destination IP address for receiving an Echo Reply packet
]
item 1.4.1.2
presentation [
To provide the information about the IP addresses that a user packet traverses along
the path to the destination, which of the following does Tracert record in each expired
ICMP TTL packet?
<choice ident="A">Destination port
<choice ident="B">Source port
<choice ident="C">Destination address
<choice ident="D">Source address
]
item 1.4.2.1
correct-response = "A,B,D"
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements regarding the verification of IP connectivity are
false? (Three Answers)
<choice ident=A>The ping 127.0.0.1 command can be used to check whether the
network cable is correctly inserted into the hosts Ethernet port.
<choice ident=B>The ping command with the host IP address as the destination
can be used to verify that the TCP/IP protocol suite is functioning correctly.
<choice ident=C> The ping command can be used to verify connectivity between
the host and the local gateway.
<choice ident=D> The command ipconfig /release can be used to check
2017-1-24
8 , 91
connectivity problems between the host and the local gateway.

]
item 1.4.2.2
cardinality =multiple
minnumber = 2
maxnumber = 2
presentation [
A network administrator uses the ping command to check for points of failure in the
network. Which protocols will be used during this process? (Two Answers)
<choice ident=A> ICMP.
<choice ident=B> TCP.
<choice ident=C> ARP.
<choice ident=D> UDP.
]
item 1.4.2.3
correct-response = "B,C"
minnumber = 2
maxnumber = 2
presentation [
A network administrator recently used tracert to trace the path to the destination IP
address of an external website, however the trace path displayed only a timeout
result. Which of the following statements correctly explains the reason for this? (Two
Answers)
<choice ident=A> The source router had shutdown the ICMP function.
<choice ident=B> This destination IP address does not exist.
<choice ident=C> The gateway canot find a route to the destination.
<choice ident=D> This is a normal phenomenon.
]
item 1.4.2.4
correct-response = "A"
presentation [
Ping 10.0.0.2 : 56 data bytes, press CTRL_C to break
Reply from 10.0.0.2 : bytes=800 Sequence=1 ttl=255 time=2 ms
Reply from 10.0.0.2 : bytes=800 Sequence=2 ttl=255 time=10 ms
--- 10.0.0.2 ping statistics --2 packet(s) transmitted
2 packet(s) received
0.00% packet loss
round-trip min/avg/max = 2/6/10 ms
A network administrator uses the ping command to test connectivity to the destination
10.0.0.2 on a Huawei AR series router. Which statement regarding the output is
correct?
<choice ident=A> The network administrator used the command ping -c 2 -s 800
10.0.0.2
<choice ident=B> The network administrator used the command ping -a 2 -v 800
2017-1-24
9 , 91
10.0.0.2
<choice ident=C> The path between the source and destination is not OK.
<choice ident=D> The network administrator changed the default TTL value.
]
item 1.4.2.5
correct-response = "A,D"
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements explains the behavior of the ICMP redirect
function? (Two Answers)
<choice ident=A> When a router receives data on the interface via which the same
data needs to be forwarded, and the source is on the same segment as the next hop,
an ICMP redirect message will be sent by the router to the source.
<choice ident=B> When a router receives data on an interface, and the routers IP
address matches the destination IP of the data, an ICMP redirect message will be
sent by the router to the source.
<choice ident=C> When a router receives data on the interface via which the same
data needs to be forwarded, and the source is on the same segment as the next hop,
an ICMP Redirect message will be sent by the source to the router.
<choice ident=D> When a router receives data on the interface via which the same
data needs to be forwarded, and the source is on a different segment from the next
hop, an ICMP redirect message will be sent by the router to the source.
]
item 1.5.1.1
correct-response = "A "
presentation [
Refer to the graphic. Host A wishes to send data to host C, and generates an ARP
request to obtain the destination MAC address. Which statement is true?
<choice ident=A> The destination IP address of the ARP request is Host C
<choice ident=B> The destination MAC address of this ARP request is Host C
<choice ident=C> The destination IP address for the ARP request is a broadcast IP
address.
<choice ident=D> The destination MAC address of this frame is the MAC address
of G0/0/0 on RTA.
]
item 1.5.1.2
presentation [
Refer to the graphic. An ARP request is sent by host A to obtain the destination MAC
address of host D. Which statement is true about regarding the ARP reply?
<choice ident=A> The destination MAC address of this frame is the MAC address of
Switch A.
<choice ident=B> The destination IP address of this packet is the VLANIF1 IP
address of Switch A.
2017-1-24
10 , 91
<choice ident=C> The destination MAC address of this frame is the MAC address
of Host A.
<choice ident=D> The destination IP address of this packet is a broadcast IP
address.
]
item 1.5.1.3
presentation [
Which of the following applications can be used to detect the path along which the
data packets are transmitted from the source to the destination?
<choice ident="A">route
<choice ident="B">netstat
<choice ident="C">tracert
<choice ident="D">send
]
item 1.5.1.4
presentation [
How many probe packets are sent for each TTL value by default when"tracert" is
used to detect the path along which packet is sent from source to destination?
<choice ident="A">3
<choice ident="B">4
<choice ident="C">6
<choice ident="D">8
]
item 1.5.1.5
minnumber = 2
maxnumber = 2
presentation [
Which of the following types can ICMP packets be classified into? (Select 2
Answers)
<choice ident="A">ICMP transport packet
<choice ident="B">ICMP error reporting packet
<choice ident="C">ICMP query packet
<choice ident="D">ICMP application packet
]
item 1.5.1.6
presentation [
On VRP platform, which of the following parameters can be used together with the
"ping" command to specify the source address of an echo request message?
<choice ident="A">-a
<choice ident="B">-s
<choice ident="C">-d
2017-1-24
11 , 91
<choice ident="D">-n
]
item 1.5.1.7
minnumber = 2
maxnumber = 2
presentation [
A router functioning as a Proxy receives an ARP request packet, but finds that the
destination address in the packet is not intended for itself. In this case, what will the
router do? (Select 2 Answers)
<choice ident="A">Discard the packet.
<choice ident="B">Check for a route that matches the destination address.
<choice ident="C">Forward its MAC address to the ARP request sender after finding
that a route to the destination address is available.
<choice ident="D">Broadcast the ARP request packet.
]
item 1.5.2.1
presentation [
Refer to the exhibit. Two end stations in a point-to-point network perform address
resolution. Which of the following statements is correct?
<choice ident=A> The destination address of an ARP request from each station will
be a unicast MAC address.
<choice ident=B> The destination address of an ARP request from each station will
be a broadcast IP address.
<choice ident=C> The destination address of an ARP reply from each station will be
a unicast MAC address.
<choice ident=D> The destination address of an ARP reply from each station will be
a broadcast MAC address.
]
item 1.5.3.1
presentation [
Refer to the exhibit. What will the destination MAC address be at the moment a
frame is transmitted by the host, when the router is the IP destination?
<choice ident=A> The MAC address of the switch.
<choice ident=B> The MAC address of the router interface G0/0/0.
<choice ident=C> The MAC address of the host.
<choice ident=D> The destination MAC address will be a broadcast MAC address.
]
item 1.5.3.2
correct-response = "ab"
2017-1-24
12 , 91
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements about gratuitous ARP packets are true? (Select 2
Answers)
<choice ident="A">A system can determine whether conflicting IP addresses are
used by sending a gratuitous ARP packet.
<choice ident="B">A gratuitous ARP packet uses the same format as an ARP request
packet.
<choice ident="C">A gratuitous ARP packet can help to update an IP address.
<choice ident="D">A gratuitous ARP packet uses the same format as an ARP reply
packet.
]
item 1.6.1.1
minnumber = 2
maxnumber = 2
presentation [
A client failed to transfer a file to the FTP server, but found the IP connectivity was
without problem. The client assumed that the problem was with the port
configuration. The blocking of which ports would likely cause this problem? (Two
Answers)
<choice ident=A> 21
<choice ident=B> 80
<choice ident=C> 20
<choice ident=D> 50649
]
item 1.6.1.2
presentation [
UDP is connectionless oriented, which of the following must be used in order to
ensure reliability?
<choice ident="A">Internet Protocol
<choice ident="B">Application Layer Protocol
<choice ident="C">Network Layer Protocol
<choice ident="D">Transmission Control Protocol
]
item 1.7.1.1
presentation [
The administrator has configured an IP address for Host A and Host B, but had
forgotten to configure a default gateway. What effect will this have on the hosts?
<choice ident=A> Neither host will be affected, and therefore will be able to
communicate with the peer.
<choice ident=B> Host A will be unable to connect to the routers G0/0/0 interface.
2017-1-24
13 , 91
<choice ident=C> Hosts will be unable to comminicate unless arp-proxy is enabled

on the router.
<choice ident=D> The host will be unable to reach neither the local nor remote
network destinations .
]
item 1.7.1.2
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. A host has established a telnet connection with the router
attached to interface G0/0/0. Which of the following statements are correct? (Two
Answers)
<choice ident=A> The destination address of a frame sent by the host will be the
MAC address of the router interface.
<choice ident=B> The destination address of a frame will be the MAC address of
the switch interface.
<choice ident=C> The destination port number in a segment header will have a
value of 80.
<choice ident=D> The destination IP address of a packet will be the IP address of
the network interface of the router.
]
item 1.7.1.3
presentation [
Refer to the graphic. The administrator uses the ping command on the host to test
connectivity to the website www.huawei.com. The command line shows a request
time out. The administrator displays the ARP entries for the host. Which entry will be
found in the ARP cache table of the host?
<choice ident=A>The MAC address of the destination www.huawei.com will exist in
the ARP cache.
<choice ident=B> The MAC address of the switch will exist in the ARP cache.
<choice ident=C> The IP address of the destination www.huawei.com will exist in
the ARP cache.
<choice ident=D> The MAC address of router interface G0/0/0, will exist in the ARP
cache.
]
item 1.7.2.1
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. When R2 forwards data to R3 from R1, which of the following
2017-1-24
14 , 91
items will change

(Two Answers)
<choice ident=A>The source MAC address
<choice ident=B>The destination MAC address
<choice ident=C>The source IP address
<choice ident=D>The destination IP address
]
item 1.7.2.2
correct-response = "C "
minnumber = 1
maxnumber = 1
presentation [
Refer to the graphic. If Host B also configured the IP address as 192.168.1.1/24, an
IP address confict will occur. What will happen as a result?
<choice ident=A> Host B will send an ICMP request to the destination with the
configured IP address. If a reply is received, the host will notify of an address conflict.
<choice ident=B> Host A will send a gratuitous ARP request to resolve the MAC
address of the destination 192.168.1.1, for which Host B will reply.
<choice ident=C> Host B will send a gratuitous ARP request to resolve the MAC
address of the destination 192.168.1.1, for which Host A will reply.
<choice ident=D> Host A will ignore any received ARP request intended for
destination 192.168.1.1.
]
item 1.7.2.3
minnumber = 2
maxnumber = 2
correct-response = "C,D"
presentation [
Refer to the graphic. The host has a problem establishing a telnet connection with
the router attached to interface G0/0/0, Which of the following steps can be used to
help the administrator identify the problem? (Two Answers)
<choice ident=A> Check whether the host has configured the gateway IP address.
<choice ident=B> Check whether the switch has configured the gateway IP
address.
<choice ident=C> Use the ping tool to check connectivity between host and router.
<choice ident=D> Check the telnet server configuration is right on the router.
]
item 2.1.1.1
correct-response = "abc"
minnumber = 3
maxnumber = 3
presentation [
Which of the following methods are supported by VRP platform to configure the
router? (Select 3 Answers)
2017-1-24
15 , 91
<choice ident="A">Through the Console port

<choice ident="B">Through Telnet
<choice ident="C">Through the AUX port
<choice ident="D">Through FTP
]
item 2.1.1.2
minnumber = 2
maxnumber = 2
presentation [
The administrator wishes to update the configuration file of an AR2200 router using a
USB cable. How can this be achieved? (Two Answers)
<choice ident=A> The administrator should connect the USB cable between the
terminal and the mini USB port of the AR2200 router.
<choice ident=B> The administrator should connect the USB cable between the
terminal and the USB port of the AR2200 router.
<choice ident=C> The AR2200 router cannot support configuration updates through
a USB cable.
<choice ident=D> The administrator should install the mini USB drivers on the
terminal after connecting the USB.
]
item 2.1.1.3
presentation [
The administrator wishes to manage a network through telnet from a user's terminal
to a router. How can this be achieved?
<choice ident=A>A connection should be established between the ethernet port of
the terminal and the console port of the router.
<choice ident=B> A connection should be established between the ethernet port of
the terminal and the ethernet port of the router.
<choice ident=C> A connection should be established between the console port of
the terminal and the ethernet port of the router.
use console cable connect pcs ethernet port and routers console port.
<choice ident=D> A connection should be established between the COM port of the
terminal and the console port of the router.
]
item 2.1.1.4
minnumber = 2
maxnumber = 2
presentation [
Whilst configuring a device, an administrator experiences trouble remembering
certain commands. Which of the following will help support the administrator? (Two
Answers)
<choice ident=A>TAB
<choice ident=B>question mark
2017-1-24
16 , 91
<choice ident=C>ctrl+b
<choice ident=D>ctrl+c
]
item 2.1.1.5
presentation [
<Huawei> system-view
[Huawei] user-interface console 0
[Huawei-ui-console0] user privilege level 15
[Huawei-ui-console0] authentication-mode password
[Huawei-ui-console0] set authentication password cipher huawei2012
[Huawei-ui-console0] quit
Refer to the configuration output. The administrator configured the device using the
commands in the configuration output. Regarding these commands, which statement
is false?
<choice ident=A> The administrator wishes to enable management through the
console interface.
<choice ident=B> Following configuration, the administrator cannot manage the
device remotely.
<choice ident=C> A user that logs-in through the console interface is assigned the
highest privilege level.
<choice ident=D> The password of a user logged in through console is cipher
huawei2012
]
item 2.1.1.6
presentation [
Which of the following is abbreviation of VRP?
<choice ident="A">Versatile Routine Platform
<choice ident="B">Virtual Routing Platform
<choice ident="C">Virtual Routing Plane
<choice ident="D">Versatile Routing Platform
]
item 2.1.1.7
presentation [
Which of the following must be used to establish the configuration environment when
a router is powered on for the first time?
<choice ident="A">SSL
<choice ident="B">SSH
<choice ident="C">Console port
<choice ident="D">Telnet
]
item 2.1.3.1
2017-1-24
17 , 91
presentation [
Which of the following parameter settings for terminal emulation are correct when
configuring a Huawei router through the Console port?
<choice ident="A">4800bps, 8 data bits,1 stop bits, odd parity check, and no flow
control
<choice ident="B">9600bps, 8 data bits, 1 stop bits, no parity check, and no flow
control
<choice ident="C">9600bps, 8 data bits, 1 stop bits, even parity check, and hardware
flow control
<choice ident="D">19200bps, 8 data bits, 1 stop bits, no parity check, and no flow
control
]
item 2.2.1.1
presentation [
Which of the following commands is used to enter the system-view from the user
view on a Huawei router?
<choice ident="A">system-view
<choice ident="B">enable
<choice ident="C">configure terminal
<choice ident="D">interface system
]
item 2.2.1.2
presentation [
On VRP platform, the command lines are classified into four levels in increasing
priority: Visit level, Monitoring level, Configuration level, and Management level. At
which level, the operator is permitted to configure service but is not permitted to
operate the file system?
<choice ident="A">Visit level
<choice ident="B">Monitoring level
<choice ident="C">Configuration level
<choice ident="D">Management level
]
item 2.2.1.3
minnumber = 2
maxnumber = 2
presentation [
On Huawei VRP platform, which of the following can be used to invoke the history
command saved by the command line interface? (Select 2 Answers)
<choice ident="A">Up cursor key < >
<choice ident="B">Left cursor key <
>
<choice ident="C">Ctrl+P
2017-1-24
18 , 91
<choice ident="D">Ctrl+U
]
item 2.2.1.4
presentation [
Which of the following commands can be used to view the current configurations on
a Huawei router?
<choice ident="A">display current-configuration
<choice ident="B">display saved-configuration
<choice ident="C">view saved-configuration
<choice ident="D">show startup-configuration
]
item 2.2.1.5
presentation [
The administrator wishes to change name of the router. Under which view should the
administrator be in order to achieve this?
<choice ident=A> User-view
<choice ident=B> System-view
<choice ident=C> Interface-view
<choice ident=D> Protocol-view
]
item 2.2.1.6
presentation [
<Huawei> system-view
[Huawei]command-privilege level 3 view user save
Refer to the command output. What is the result of the shown command?
<choice ident=A> The command adjusts the save command of a user to privilege
level 3.
<choice ident=B> The command adjusts the save command in the user view to
privilege level 3.
<choice ident=C> The command adjusts the user view command privilege level to
3, and saves the configuration.
<choice ident=D> The command adjusts the privilege level of a user to 3, and
saves the configuration.
]
item 2.2.1.7
minnumber = 2
maxnumber = 2
presentation [
<Huawei>system-view
2017-1-24
19 , 91
[Huawei]history-command max-size 20
Refer to the command output. Which statements regarding the shown command are
true? (Two answers)
<choice ident=A> The command is used to adjust the size of
the history command buffer.
<choice ident=B> The default value of the history command buffer is 5.
<choice ident=C> The command should be configured in the user-interface view.
<choice ident=D> Once configured, commands totalling up to 20 bytes can be
saved in the buffer.
]
item 2.2.1.8
minnumber = 2
maxnumber = 2
presentation [
An AR2200 router is required to be reconfigured from scratch. Which steps are
needed to achieve this? (Two Answers)
<choice ident=A> Reset the saved configuration
<choice ident=B> Clear the current configuration
<choice ident=C> Reboot the AR2200.
<choice ident=D> Assign the configuration file to be used at next startup.
]
item 2.2.1.9
presentation [
An adminstrator has been requested to replace the configuration file of a router in the
network. The administrator has been instructed that after logging into the router, he
must first permenantly erase the current configuration file config.zip from the system.
Which command should he use to achieve this?
<choice ident=A> delete /force config.zip
<choice ident=B> delete /unreserved config.zip
<choice ident=C> reset config.zip
<choice ident=D> clear config.zip
]
item 2.2.2.1
presentation [
Which of the following commands can switch a view from the system view to the user
view?
<choice ident="A">System-view
<choice ident="B">Router
<choice ident="C">Quit
<choice ident="D">User-view
]
2017-1-24
20 , 91
item 2.3.1.1
correct-response = "abce"
minnumber = 4
maxnumber = 4
presentation [
Which of the following storage devices are supported by Huawei router? (Select 4
Answers)
<choice ident="A">SDRAM
<choice ident="B">NVRAM
<choice ident="C">Flash
<choice ident="D">Hard Disk
<choice ident="E">CF Card
]
item 2.3.1.2
presentation [
Which of the following storage devices is used to store the startup configuration files
in a router?
<choice ident="A">SDRAM
<choice ident="B">NVRAM
<choice ident="C">Flash
<choice ident="D">BootROM
]
item 2.3.1.3
presentation [
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If
you perform configurations when Auto-Config is running, the DHCP, routing, DNS,
and VTY configurations will be lost. Do you want to stop Auto-Config? [y/n]:
When an administrator first initializes the router, a warning is displayed. Which
statement regarding this warning is correct?
<choice ident=A> If Auto-Config is required, the administrator should select y
<choice ident=B> If Auto-Config is not required, the administrator should select n,
for which subsequent configuration of the DHCP server, routing, DNS server and
VTY user configuration is lost.
<choice ident=C> When a device is started for the first time, the Auto-Config
function is active.
<choice ident=D> When a device is started for the first time, the Auto-Config
function is inactive.
]
item 2.3.1.4
2017-1-24
21 , 91
minnumber = 2
maxnumber = 2
presentation [
<Huawei>reset saved-configuration
Warning: The action will delete the saved configuration in the device.
The configuration will be erased to reconfigure. Continue? [Y/N]:
Refer to the configuration output. Which of the following statements are true? (Select
two answers)
<choice ident=A> A user should enter Y when wishing to clear the saved
configuration file.
<choice ident=B> The saved-configuration file that the device starts with can be
erased.
<choice ident=C> The saved-configuration will be deleted after typing N
<choice ident=D> The saved-configuration file will be replaced with the currentconfiguration.
]
item 2.3.3.1
presentation [
When a router is powered on, the router reads the configuration file saved in the
default save directory to get itself initialized. If the configuration file does not exist in
the default save directory, what does the router use to initialize itself?
<choice ident="A">New configuration file
<choice ident="B">Initial configuration file
<choice ident="C">Default parameters
<choice ident="D">Current configuration file
]
item 2.4.1.1
presentation [
<Huawei>display startup
MainBoard:
Startup system software:
Next startup system software:
Backup system software for next startup:
Startup saved-configuration file:
Next startup saved-configuration file:
Startup license file:
Next startup license file:
Startup patch package:
Next startup patch package:
Startup voice-files:
Next startup voice-files:
sd1:/ar2220-v200r003c00spc200.cc
sd1:/ar2220-v200r003c00spc200.cc
null
null
null
null
null
null
null
null
null
Refer to the display output. Which statement is false?

<choice ident=A>The current configuration file has not been saved.
<choice ident=B>The current startup system software is ar22202017-1-24
22 , 91
v200r003c00spc200.cc
<choice ident=C>The next startup system software cannot be changed.
<choice ident=D>The next startup system software can be changed by using the
startup system software <startup-software-name>.cc command.
]
item 2.4.1.2
minnumber = 3
maxnumber = 3
presentation [
An administrator wishes to update the VRP software of companys AR2200 router.
How can this be achieved? (Three Answers)
<choice ident=A> The administrator can use FTP to transfer the VRP software, with
the AR2200 router as the FTP client.
<choice ident=B> The administrator can use FTP to transfer the VRP software, with
the AR2200 router as the FTP server.
<choice ident=C> The administrator can use TFTP to transfer the VRP software,
with the AR2200 router as the TFTP server.
<choice ident=D> The administrator can use TFTP to transfer the VRP software,
with the AR2200 router as the TFTP client.
]
item 2.4.1.3
presentation [
An administrator wishes to implement new features in the network, but the VRP
version of one AR2200 router is out of date. The adminstrator needs to upgrade the
VRP software. Which of the following options regarding file transfer is false?
<choice ident=A> The AR2200 router can function as a TFTP client to support the
upgrade.
<choice ident=B> The AR2200 router can function as the TFTP server to support
the upgrade.
<choice ident=C> The AR2200 router can function as the FTP server to support the
upgrade.
<choice ident=D> The AR2200 router can function as an FTP client to support the
upgrade.
]
item 2.4.1.4
presentation [
An AR2200 router in the company network cannot boot. In order to resolve this, the
administrator wishes to update the VRP software. What should he/she do?
<choice ident=A> The administrator should use a console cable to connect the
router and host, and directly upgrade the device.
<choice ident=B>The administrator should use FTP to transfer the VRP software,
by configuring the AR2200 router as an FTP client.
<choice ident=C>The administrator should use DHCP to boot the AR2200, and then
use the AR2200 router as a TFTP client to download the VRP software from the
server.
2017-1-24
23 , 91
<choice ident=D>The administrator should use the telnet command on the client to
remote access the device, and upgrade the VRP software.
]
item 2.4.1.5
correct-response = "B,D"
minnumber = 2
maxnumber = 2
presentation [
<Huawei>
Warning: Auto-Config is working. Before configuring the device, stop Auto-Config. If
you perform configurations when Auto-Config is running, the DHCP, routing, DNS,
and VTY configurations will be lost. Do you want to stop Auto-Config? [y/n]:
Refer to the output. When the administrator first starts the router, a system notice is
displayed, however after rebooting this router, the notice disappeared. What is the
reason for this? (Two Answers)
<choice ident=A> This notice only appears during the very first device startup.
<choice ident=B> The administrator has configured the device and saved the
configuration, causing the notice to disappear.
<choice ident=C> The administrator selected n and did not save the configuration.
<choice ident=D> The administrator selected y and saved the configuration.
]
item 2.4.2.1
minnumber = 3
maxnumber = 3
presentation [
FTP and TFTP can be used to update the system file on Huawei routers. Which of
the following statements are correct? (Select 3 Answers)
<choice ident="A">Huawei router can be configured as FTP Client
<choice ident="B">Huawei router can be configured as FTP Server
<choice ident="C">Huawei router can be configured as TFTP Client
<choice ident="D">Huawei router can be configured as TFTP Server
]
item 3.1.1.1
correct-response = " C"
presentation [
<Quidway>display mac-address
------------------------------------------------------------------------------MAC Address VLAN/VSI Learned-From Type
------------------------------------------------------------------------------5489-98ec-f018 1/GE0/0/13
dynamic
------------------------------------------------------------------------------Total items displayed = 1
Refer to the graphic. A switch attempts to forward a frame to the MAC destination
2017-1-24
24 , 91
5489-98ec-f01. What operation will occur on the switch?

<choice ident=A> The switch will send a request to obtain the MAC address of
5489-98ec-f011.
<choice ident=B> The switch will report that the destination is unreachable and
report this to the source.
<choice ident=C> The switch will flood the frame via all ports, with exception of the
port on which the frame was received.
<choice ident=D> The switch will drop the frame because it does not have an entry
in its MAC address table.
]
item 3.1.1.2
presentation [
Host A has been connected to switch A and configured with an IP address. When
Host A initially forwards a frame, what action will be taken by Switch A?
<choice ident=A> Switch A will drop this frame.
<choice ident=B> Switch A will attempt to flood the frame to all ports except for the
G0/0/1 interface.
<choice ident=C> Switch A will forward the frame via ports G0/0/1, G0/0/2 and
G0/0/3.
<choice ident=D>Switch will receive this frame before returning the frame to
G0/0/1.
]
item 3.1.1.3
correct-response = "B,C"
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. Which of the following statements describes the network
shown? (Two Answers)
<choice ident=A> There are 6 collision domains in the network.
<choice ident=B> There are 2 broadcast domains in the network.
<choice ident=C> There are 4 collision domains in the network.
<choice ident=D> There are 6 broadcast domains in the network.
]
item 3.1.2.1
presentation [
A server is linked to port interface G0/0/1 of a switch. The administrator wishes to
allow only this server to be linked to this interface on the switch. Which method can
be used to achieve this?
<choice ident=A>Configure a static ARP entry using the servers IP address and
MAC address in the switch.
2017-1-24
25 , 91
<choice ident=B>Configure a static MAC address binding entry of the servers MAC
address and the interface in the switch.
<choice ident=C>Configure the default gateway of the switch to be the same as the
servers IP address.
<choice ident=D>It is not possible to enable a single device to be associated with
an interface.
]
item 3.1.2.2
correct-response = "A "
presentation [
An administrator connects two switches together in a local enterprise network. The
ports of one switch support Fast Ethernet, while the ports of the other switch support
Gigabit Ethernet. Hosts connected to one switch are able to communicate, however
communication between the two switches fails. What is the possible reason for this?
<choice ident=A> The ports have disabled auto-negoatition.
<choice ident=B> One port is supporting auto-negotiation, while auto-negotiation is
disabled on the port of the other switch.
<choice ident=C>The port of one switch is operating using half duplex mode, while
the port of the other switch is using full duplex mode.
<choice ident=D>A Fast Ethernet port cannot communicate directly with a Gigabit
Ethernet port.
]
item 3.1.2.3
presentation [
A layer 2 LAN switch generates CAM table entries according to the ( ) of the
received frame.
<choice ident="A">Source MAC address
<choice ident="B">Destination MAC address
<choice ident="C">Source IP address
<choice ident="D">Destination IP address
]
item 3.1.2.4
correct-response = "abd"
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements about collision domains and broadcast domains
are correct? (Select 3 Answers)
<choice ident="A">Devices connected to the same hub form a collision domain
<choice ident="B">Devices connected to the same hub form a broadcast domain
<choice ident="C">Devices connected to the same bridge form a collision domain
<choice ident="D">Devices connected to the same bridge form a broadcast domain
<choice ident="E">Devices connected to the same router form a broadcast domain
]
2017-1-24
26 , 91
item 3.1.2.5
presentation [
Which of the following statements regarding layer-2 switch is incorrect?
<choice ident="A">The switch learns MAC addresses automatically
<choice ident="B">The layer-3 header is modified before the received packet is
transmitted
<choice ident="C">The layer-2 header is modified before the received packet is
transmitted.
<choice ident="D">The layer-2 LAN switch operates at data link layer
]
item 3.2.1.1
presentation [
Redundant paths exist in switched network. Which of the following technologies can
be used to prevent looping and increase the network reliability?
<choice ident="A">STP
<choice ident="B">Split horizon
<choice ident="C">Poison reverse
<choice ident="D">Shortest path tree
]
item 3.2.1.2
presentation [
which STP protocol is enabled on the Sx7 series switch by default?
<choice ident=A>STP
<choice ident=B>RSTP
<choice ident=C>MSTP
<choice ident=D>All STP based protocols are disabled by default
]
item 3.2.1.3
correct-response = "C "
presentation [
Users in the network discovered that the efficiency of a file transfer is low. The
administrator used wireshark to observe the network and discovered many duplicate
frames. Which statement correctly explains the reason for this?
<choice ident=A> The switch doesnt know the destination and has flooded frames.
<choice ident=B> This network needs upgrading to use newer and more efficient
switches.
<choice ident=C>The network has loops at the link layer.
<choice ident=D>The network has not been segmented using VLANs.
]
item 3.2.1.4
2017-1-24
27 , 91
correct-response = "B,C,D"
minnumber = 3
maxnumber = 3
presentation [
Refer to the graphic. What will happen in this figure if the STP protocol is disabled on
both switches? (Three Answers)
<choice ident=A> Load balancing will occur in this topology.
<choice ident=B> CPU usage will be very high on S1 and S2 due to a broadcast
floods.
<choice ident=C>The MAC address of host B can be found in the MAC address
table of both switches.
<choice ident=D>Duplicate frames exist in this network.
]
item 3.2.1.5
presentation [
MSTID Port
Role STP State Protection
0 GigabitEthernet0/0/1
DESI FORWARDING
NONE
DESI FORWARDING
NONE
DESI FORWARDING
NONE
DESI FORWARDING
NONE
DESI FORWARDING
NONE
DESI FORWARDING
NONE
Refer to the display output. The display stp brief command is used to check the
summary STP information of a switch. With regards to the output, which of the
following statements is incorrect?
<choice ident=A> The network may or may not contain a single switch.
<choice ident=B> This switch is the root switch of this network.
<choice ident=C> This switch is the designated switch to any peering switches.
<choice ident=D> This switch must have linked to 6 hosts through the 6 interfaces
displayed.
]
item 3.2.1.6
presentation [
Refer to the graphic. Both switches are operating using STP. With exception to those
shown, all other default parameters have been maintained. Which port will be
blocked?
<choice ident=A> Port G0/0/1 of switch A
<choice ident=B> Port G0/0/2 of switch B
<choice ident=C> Port G0/0/1 of switch B
<choice ident=D> Port G0/0/2 of switch A
]
2017-1-24
28 , 91
item 3.2.1.7
presentation [
Which of the following descriptions about STP designated ports is correct?
<choice ident="A">Each bridge can have only one designated port
<choice ident="B">Designated ports are responsible for sending BPDU to connected
network segments
<choice ident="C">Designated ports represent the path leading to the root switch
<choice ident="D">Designated ports forward frames destined for the root switch
]
item 3.2.1.8
presentation [
What is the default value of switch priority when STP is enabled on Huawei switch?
<choice ident="A">4096
<choice ident="B">8192
<choice ident="C">16384
<choice ident="D">32768
]
item 3.2.1.9
presentation [
Which of the following descriptions regarding the STP forwarding state is incorrect?
<choice ident="A">A port in a forwarding state can receive BPDU
<choice ident="B">A port in a forwarding state does not learn the source MAC
address of a frame.
<choice ident="C">A port in a forwarding state can forward frames
<choice ident="D">A port in a forwarding state can send BPDU
]
item 3.2.1.10
presentation [
Assuming all STP enabled switches have the same bridge priority. The MAC address
of switch A is 00-e0-fc-00-00-40, the MAC address of switch B is 00-e0-fc-00-00-10,
the MAC address of switch C is 00-e0-fc-00-00-20, and the MAC address of switch D
is 00-e0-fc-00-00-80. Which switch will be elected as the root switch?
<choice ident="A">Switch A
<choice ident="B">Switch B
<choice ident="C">Switch C
<choice ident="D">Switch D
]
2017-1-24
29 , 91
item 3.2.1.11
minnumber = 2
maxnumber = 2
presentation [
What problems can result from a switching loop in a network? (Select 2 Answers)
<choice ident="A">Increased link bandwidth
<choice ident="B">Broadcast storms
<choice ident="C">CAM table instability
<choice ident="D">Port aggregation failure
]
item 3.2.1.12
presentation [
During STP calculation, the port cost is associated with port bandwidth. Which of the
following statements about the relation between port cost and port bandwidth is true?
<choice ident="A">Port cost decreases when port bandwidth increases.
<choice ident="B">Port cost increases when port bandwidth.
<choice ident="C">Port cost is consistent with port bandwidth.
<choice ident="D">Port cost varies randomly according to port bandwidth.
]
item 3.2.1.13
presentation [
The administrator has discovered a power failure on a switch in the company
network. The switch has been replaced with an x7 series switch. The new switch is to
become the root bridge for the network. What should be done to ensure this is
achieved?
<choice ident=A> Assign the switch an IP address with a value lower than all other
switch IP addresses.
<choice ident=B> Set the root path cost to a lower value on all ports of the switch.
<choice ident=C> Set the bridge priority with a value lower than all other switches.
<choice ident=D> Change the MAC address of the switch to a lower value than all
other swich MAC addresses.
]
item 3.2.1.14
presentation [
A network administrator of a company wishes to manually define the position of the
spanning tree root bridge. Which of the following will allow this to be achieved?
<choice ident=A> Set the switch priority on the switch to become the root bridge to
a supported priority value that is lower than all other switches.
<choice ident=B> Set the switch MAC address on the switch to become the root
2017-1-24
30 , 91
bridge to use an address lower than all other switch MAC addresses.
<choice ident=C> Set the MAC address on the switch to become the root bridge to
use an address value higher than all other switch MAC addresses.
<choice ident=D> Set the switch priority on the switch to become the root bridge to
a supported priority value that is higher than all other switches.
]
item 3.2.2.1
correct-response= "abd"
presentation [
Which of the following descriptions about STP are incorrect?
<choice ident="A">A layer-2 switching network can have only one designated switch
<choice ident="B">All the ports of the root switch are root ports
<choice ident="C">All the ports of the root switch are designated ports
<choice ident="D">The switch with the smallest priority value is elected as non-root
switch
]
item 3.2.2.2
correct-response= "ad"
presentation [
In STP, which of the following items may affect the selection of the root switch?
<choice ident="A">Switch priority
<choice ident="B">Switch port ID
<choice ident="C">Switch interface bandwidth
<choice ident="D">Switch MAC address
<choice ident="E">Switch IP address
]
item 3.2.2.3
presentation [
A port directly connects to a designated port on the peer device and is used to
receive BPDU to monitor the changes occurring in the network. However, it does not
forward any packet. Which of the following ports represents this port?
<choice ident="A">Root Port
<choice ident="B">Designated Port
<choice ident="C">Alternate Port
<choice ident="D">Disable Port
]
item 3.2.2.4
presentation [
blocked?
2017-1-24
31 , 91

<choice ident=C> Port G0/0/1 of switch B
<choice ident=D> Port G0/0/2 of switch A
]
item 3.2.2.5
minnumber = 2
maxnumber = 2
presentation [
shown, all other default parameters have been maintained. Which ports will be
assigned a designated port role? (Two Answers)
<choice ident=C> Port G0/0/2 of switch A
<choice ident=D> Port G0/0/2 of switch B
]
item 3.2.2.6
presentation [
Refer to the graphic. The switch is operating using STP. All default parameters have
been maintained. Which port will be assigned a designated port role?
<choice ident=A> G0/0/1 of switch A
<choice ident=B> G0/0/2 of switch A
<choice ident=C> E0/0/1 of the hub
<choice ident=D> E0/0/2 of the hub
]
item 3.2.2.7
presentation [
Refer to the graphic. Four switches are operating using STP. One of the port
interfaces on ROOT has failed. How long will it take for the blocked interface to
change to a state of forwarding?
<choice ident=A> 30 seconds
<choice ident=B> 50 seconds
<choice ident=C> 15 seconds
<choice ident=D> 3 seconds
]
item 3.2.2.8
2017-1-24
32 , 91
presentation [
Refer to the graphic. Four switches are operating using STP. If port interface G0/0/2
on switch c fails, how long will it take for the blocked interface to change to a state of
forwarding?
<choice ident=A> 30 seconds
<choice ident=B> 50 seconds
<choice ident=C> 15 seconds
<choice ident=D> 3 seconds
]
item 3.2.3.1
presentation [
blocked?
<choice ident=C> Port G0/0/2 of switch A
<choice ident=D> Port E0/0/3 of the hub
]
item 3.2.3.2
presentation [
Refer to the graphic. All switches are operating using STP. In order to establish a
stable spanning tree, how many port interfaces can be in a forwarding state following
convergence?
<choice ident=A> 9
<choice ident=B> 8
<choice ident=C> 7
<choice ident=D> 6
]
item 3.3.2.1
presentation [
An administrator has configured the port interface G0/0/3 of Switch A as an edge
port. The user wishes to connect multiple devices to the network and connects his
own managed switch to the network. What effect will this have on the network?
<choice ident=A> Port interface G0/0/3 of switch A will shut down, as a BPDU has
been received by the edge port.
<choice ident=B> Port interface G0/0/3 of switch A will forward the data normally
and drop the BPDU sent by the host to the switch
2017-1-24
33 , 91
<choice ident=C> Switch A will receive the BPDU and recaculate the port state of
G0/0/3.
<choice ident=D>Only Host A can send data out as before, the other devices linked
cannot.
]
item 3.3.3.1
presentation [
In the RSTP standard, a port is able to connect to a terminal directly and enter the
forwarding state without delay. Which of the following ports represents such a port?
<choice ident="A">Fast port
<choice ident="B">Backup port
<choice ident="C">Root port
<choice ident="D">Edge port
]
item 3.3.3.2
presentation [
As specified by the RSTP protocol, when a designated port fails, which type of port
will function as a new designated port and enters the forwarding state without any
delay?
<choice ident="A">Forwarding Port
<choice ident="B">Alternate Port
<choice ident="C">Backup Port
<choice ident="D">Edge Port
]
item 3.3.3.3
presentation [
As specified by the RSTP protocol, when a root port fails, which type of port will
function as a new root port and enters the forwarding state without any delay?
<choice ident="A">Forwarding Port
<choice ident="B">Alternate Port
<choice ident="C">Backup Port
<choice ident="D">Edge Port
]
item 4.1.1.1
presentation [
[R1]display interface GigabitEthernet0/0/0
GigabitEthernet0/0/0 current state : Administratively DOWN
Line protocol current state : DOWN
Refer to the display output. What can be determined based on the output of the
2017-1-24
34 , 91
display command?
<choice ident=A> Interface Gigabit Ethernet 0/0/0 is connected to a wrong cable
<choice ident=B> Interface Gigabit Ethernet 0/0/0 is not associated with an IP
address.
<choice ident=C> Interface Gigabit Ethernet 0/0/0 is not associated with a
dynamically defined route.
<choice ident=D> Interface Gigabit Ethernet 0/0/0 has been manually shut down by
an administrator.
]
item 4.1.1.2
presentation [
Which of the following statements regarding static and dynamic routing is incorrect?
<choice ident=A> The static route can be easily configured and managed on the
enterprise network.
<choice ident=B> The use of dynamic routing is more convenient for the
administrator to manage the network following network convergence.
<choice ident=C> The static route can automatically recover when a link failure is
encountered.
<choice ident=D> Dynamic routing will use more resources than static routes.
]
item 4.1.1.3
presentation [
According to the default value of route preference on the VRP platform, which of the
following represent the correct sequence for direct route, static route, RIP and OSPF
if they are listed from high preference to low preference?
<choice ident="A">Direct, Static, RIP, OSPF
<choice ident="B">Direct, OSPF, Static, RIP
<choice ident="C">Direct, OSPF, RIP , Static
<choice ident="D">Direct, RIP, Static, OSPF
]
item 4.1.1.4
minnumber = 2
maxnumber = 2
presentation [
Which of the following are routed protocols? (Select 2 Answers)
<choice ident="A">IP
<choice ident="B">OSPF
<choice ident="C">BGP
<choice ident="D">IPX
]
item 4.1.1.5
2017-1-24
35 , 91
correct-response = "bd"
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements regarding the routing table are correct? (Select 2
Answers)
<choice ident="A">The next hop in the routing table is redundant because the
outgoing interface can be used for packet forwarding.
<choice ident="B">The routes from generated by different protocols have different
preferences.
<choice ident="C">The metrics of different routing protocols are comparable.
<choice ident="D">The metrics of different routing protocols are not comparable
]
item 4.1.1.6
presentation [
Which of the following commands can be used to display the routing table on a
Quidway router?
<choice ident="A">display ip path
<choice ident="B">display ip routing-table
<choice ident="C">display interface
<choice ident="D">display current-configuration
]
item 4.1.1.7
presentation [
Which of the following entries is not included in the routing table?
<choice ident="A">source address
<choice ident="B">next hop
<choice ident="C">destination address
<choice ident="D">cost
]
item 4.1.2.1
presentation [
A router has learned two routes for the same network with the same prefix. One route
has been learned via OSPF with a metric of 4882, while the other route has been
learned via RIPv2 with a metric of 4. Which route(s) will be found in the routing table?
<choice ident=A> The RIPv2 route.
<choice ident=B> The OSPF and RIPv2 routes.
<choice ident=C> The OSPF route.
<choice ident=D> Neither of these routes will be found in the routing table.
]
item 4.1.2.2
2017-1-24
36 , 91
presentation [
Assume that the router has learnt the best route to the same destination by using
RIP, OSPF and Static Route respectively. By default, the Huawei router will select the
route learnt via ( ) as the best route.
<choice ident="A">RIP
<choice ident="B">OSPF
<choice ident="C">RIPv2
<choice ident="D">Static route
]
item 4.1.2.3
minnumber = 3
maxnumber = 3
presentation [
Which of the following problems are caused by routing loops? (Select 3 Answers)
<choice ident="A">Slow convergence
<choice ident="B">Packets circulate between routers
<choice ident="C">Router restarting
<choice ident="D">Inconsistency of routing information
]
item 4.1.2.4
correct-response = "cd"
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements are incorrect? (Select 2 Answers)
<choice ident="A">The preferences for each static routes entry can be different.
<choice ident="B">By default, OSPF maintains preference over RIP.
<choice ident="C">The greater the cost, the better the route is.
<choice ident="D">For those routes to the same destination on VRP platform, the
route with a higher preference value is more preferred over the route with a lower
preference value.
]
item 4.1.2.5
presentation [
When a routing table contains multiple routes that have the same route information,
a router selects ( ) as the matched route.
<choice ident="A">the route with the lower cost metric
<choice ident="B">the route with the better preference
<choice ident="C">the route that has the longest mask
<choice ident="D">the route containing the least number of hops
]
item 4.1.2.6
2017-1-24
37 , 91
presentation [
Destination/Mask
protocol pre Cost
NexthopInterface
9.0.0.0/8
OSPF
10 50 1.1.1.1
Serial 1/0/0
9.1.0.0/16
RIP
100 5 2.2.2.2
Ethernet 0/0/1
Refer to the graphic. Which of the following statements is correct when this router
forwards the packet to the destination host 9.1.4.5?
<choice ident="A">The router selects the first entry to match the destination address
of the packet because the preference of OSPF is higher than the preference of RIP.
<choice ident="B">The router selects the second entry to match the destination
address of the packet because the cost of RIP is lower than that of OSPF.
<choice ident="C">The router selects the second entry to match the destination
address of the packet because the outgoing interface is an Ethernet interface. The
forwarding speed of an Ethernet interface is faster than the forwarding speed of a
serial interface
<choice ident="D">The router selects the second entry to match the destination
address of the packet because the router will match the most specific address.
]
item 4.1.3.1
minnumber = 2
maxnumber = 2
presentation [
How can the default route be generated? (Select 2 Answers)
<choice ident="A">Manually configured
<choice ident="B">Automatically generated by the router
<choice ident="C">Generated by dynamic routing protocols
<choice ident="D">Generated by link layer protocols
]
item 4.2.1.1
presentation [
An administrator wishes to configure a floating static route. In order to successfully
achieve this, which operation should be performed?
<choice ident=A> The adminstrator is required to configure a different preference
value for the primary static route and floating static route.
<choice ident=B> The administrator is only required to configure two static routes.
<choice ident=C> The administrator is required to configure different route tags for
the primary static route and floating static route.
<choice ident=D> The administrator is required to configure a diferent cost metric
for the primary static route and floating static route.
]
item 4.2.1.2
presentation [
2017-1-24
38 , 91
ip route-static 10.0.12.0 255.255.255.0 192.168.1.1

Refer to the command output. Which statement is true regarding this command?
<choice ident=A> The configuration represents a static route to the 192.168.1.1
network.
<choice ident=B> The configuration represents a static route to the 10.0.12.0
network.
<choice ident=C>The preference value of this configured route is 100.
<choice ident=D> If the router has learned the same destination network via a
dynamic routing protocol, the static route will always take precedence.
]
item 4.2.1.3
presentation [
A router receives a packet and the destination of the packet does not match any
entries of the routing table in the router. What will the router do?
<choice ident="A">Discard the packet directly
<choice ident="B">Fragment the packet
<choice ident="C">Forward the packet via all interfaces except the interface on which
the packet was received.
<choice ident="D">Forward the packet according to the default route if the default
route exists in the routing table, else discard the packet
]
item 4.2.1.4
presentation [
Which of the following configurations regarding default route configuration is correct?
<choice ident="A">[Quidway] ip route-static 0.0.0.0 0.0.0.0 172.16.2.1
<choice ident="B">[Quidway] ip route-static 0.0.0.0 255.255.255.255 172.16.2.1
<choice ident="C">[Quidway-GigabitEthernet0/0/1] ip route-static 0.0.0.0 0.0.0.0
172.16.2.1
<choice ident="D"><Quidway> ip route-static 0.0.0.0 0.0.0.0 172.16.2.1
]
item 4.2.1.5
presentation [
Which of the following commands is used to configure a static route on Huawei
router?
<choice ident="A">ip route-static
<choice ident="B">ip route static
<choice ident="C">route-static ip
<choice ident="D">route static ip
]
item 4.2.2.1
2017-1-24
39 , 91
correct-response = "acd"
minnumber = 3
maxnumber = 3
presentation [
Which of the following configurations regarding static route are correct? (Select 3
Answers)
<choice ident="A">ip route-static 129.1.0.0 16 serial 0
<choice ident="B">ip route-static 10.0.0.2 16 129.1.0.0
<choice ident="C">ip route-static 129.1.0.0 16 10.0.0.2
<choice ident="D">ip route-static 129.1.0.0.255.255.0.0 10.0.0.2
]
item 4.2.2.2
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements regarding the static route are correct? (Select 3
Answers)
<choice ident="A">Load balancing can be achieved when multiple static routes with
same route preference toward the same destination are configured.
<choice ident="B">By default, the route preference of static route on VRP platform is
10.
<choice ident="C">Route backup can be achieved when multiple static routes with
different route preference toward the same destination are configured.
<choice ident="D">On VRP platform, the metric for static route is 0.
]
item 4.2.2.3
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements about backup routes are true? (Select 3 Answers)
<choice ident="A">A backup route is not added to the global routing table.
<choice ident="B">A static route does not take part in data forwarding.
<choice ident="C">After the working route fails, a backup route becomes a working
route and is added to the global routing table.
<choice ident="D">A static route together with the working route takes part in data
forwarding.
]
item 4.3.1.1
presentation [
Refer to the graphic. The routing table contains the routes of the R2. Which
advertised route will not be found in the routing table of the neighboring router R1?
<choice ident=A>The route 10.0.14.0
<choice ident=B>The route 10.0.1.0
2017-1-24
40 , 91
<choice ident=C>The route 10.0.2.0

<choice ident=D>The route 10.0.3.0
]
item 4.3.1.2
presentation [
[Huawei]rip 1
[Huawei-rip-1]version 2
Refer to the command output. An administrator wishes to configure RIP. Which other
command needs to configured for RIP routes to be advertised?
<choice ident=A> import-route GigabitEthernet 0/0/1
<choice ident=B> network 192.168.1.0 0.0.0.255
<choice ident=C> network GigabitEthernet 0/0/1
<choice ident=D> network 192.168.1.0
]
item 4.3.2.1
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. RTA and RTB are running RIPv1. RTA has advertised 10.0.0.0
and 192.168.1.0 to the RIP network. Which routes will exist in the IP routing table of
RTB? (Two Answers)
<choice ident=A>10.0.0.0/8
<choice ident=B>192.168.1.1/32
<choice ident=C>10.1.12.1/32
<choice ident=D> 192.168.1.0/24
]
item 4.3.2.2
presentation [
Refer to the graphic. Two peering routers are running RIP. RTA is using RIPv1 to
advertise its routes, while RTB is using RIPv2. What effect will this have on learned
routes?
<choice ident=A> RTA and RTB will both learn the routes advertised by RIP.
<choice ident=B> RTA will learn the RIP route advertised by RTB, however RTB is
unable to learn the route advertised by RTA.
<choice ident=C> RTB will learn the RIP route advertised by RTA, however RTA is
unable to learn the route advertised by RTB.
<choice ident=D> Neither RTA nor RTB are able to learn the RIP routes advertised
by the peer.
]
2017-1-24
41 , 91
item 4.3.2.3
presentation [
advertise its routes, while RTB is using RIPv2 to advertise the route 1.1.1.1/32. How
will the route 1.1.1.1/32 appear in the IP routing table of RTA?
<choice ident=A> This route will not appear in the IP routing table of RTA.
<choice ident=B> This route will appear in the IP routing table of RTA as 1.0.0.0/8.
<choice ident=C> This route will appear in the IP routing table of RTA as 1.0.0.0/24.
<choice ident=D> This route will appear in the IP routing table of RTA as 1.0.0.0/32.
]
item 4.3.2.4
presentation [
advertise its routes, while RTB is using RIPv1 to advertise the route 1.1.1.1/32. The
administrator configures RIP version 2 multicast for interface G0/0/1 of RTB. How
will the route 1.1.1.1/32 appear in the the IP routing table of RTA?
<choice ident=A> This route will not appear in the IP routing table of RTA.
<choice ident=B> This route will appear in the IP routing table of RTA as 1.0.0.0/8.
<choice ident=C> This route will appear in the IP routing table of RTA as 1.0.0.0/24.
<choice ident=D> This route will appear in the IP routing table of RTA as 1.0.0.0/32.
]
item 4.3.2.5
minnumber = 3
maxnumber = 3
presentation [
A RIP router receives the routing update information from its neighbor. Which of the
following statements regarding routing update are correct? (Select 3 Answers)
<choice ident="A">The received route that is not in the routing table will be added
only when its hop count value is less than 16.
<choice ident="B">The received route that already exists in the routing table will be
updated only when the next hop is the router's neighbor and the cost value is smaller.
<choice ident="C">The received route that already exists in the routing table will be
updated only when the next hop is not the router's neighbor and the cost value is
smaller.
<choice ident="D">The received route that already exists in the routing table will be
updated only when the next hop is the router's neighbor and the cost value has been
changed.
]
item 4.3.2.6
presentation [
2017-1-24
42 , 91
Which of the following commands is used to display the current running state and
configuration of RIP?
<choice ident="A">display protocol rip
<choice ident="B">show rip
<choice ident="C">display rip
<choice ident="D">display this rip
]
item 4.3.2.7
presentation [
A user can view the information for the RIP protocol on a router. What does Age
time in the returned result of the command mean?
<choice ident="A">The interval of updating an RIP packet
<choice ident="B">The aging time of an RIP route
<choice ident="C">The suppression time of an RIP route
<choice ident="D">The time spent on switching between RIP routes
]
item 4.3.2.8
presentation [
After a command for displaying RIP route information is entered on a router, peer
192.168.1.2 on Serial1/0/0 is displayed in the returned result. What does 192.168.1.2
stand for?
<choice ident="A">Address of a RIP neighbor
<choice ident="B">Address of the port with the RIP protocol enabled
<choice ident="C">Next hop address of the RIP route
<choice ident="D">Transmission address of the RIP protocol
]
item 4.3.2.9
minnumber =2
maxnumber =2
presentation [
Refer to the grapic. An administrator has configured RIPv2 on the two routers,
following which he implements the command silent-interface s0/0/1 on RTA. What
effect will this command have on the network? (Two Answers)
<choice ident=A> RTA will continue to learn routes from RTB
<choice ident=B> RTB will continue to learn routes from RTA
<choice ident=C> RTA will have no neighbor relationship with RTB
<choice ident=D> RTB will have no adjacency relationship with RTA
]
item 4.3.3.1
2017-1-24
43 , 91
presentation [
Refer to the graphic. R1,R2 and R3 are running RIPv1. R1 and R3 both advertise
172.16.0.0 to the RIP network. How will this affect R2?
<choice ident=A>R2 will not have a route to the networks 172.16.1.0/24 and
172.16.2.0/24
<choice ident=B>R2 will only have a route to 172.16.1.0/24
<choice ident=C>R2 will only have a route to 172.16.2.0/24
<choice ident=D>R2 will have a route to both networks 172.16.1.0/24 and
172.16.2.0/24, but some packets for these destinations will be lost.
]
item 4.3.3.2
presentation [
<R2>debugging rip 1
Sep 13 2013 11:07:20.974.1-05:13 R2 RIP/7/DBG: 6: 13414: RIP 1: Receiving v1
response on GigabitEthernet0/0/0 from 10.0.12.1 with 1 RTE
Sep 13 2013 11:07:20.974.2-05:13 R2 RIP/7/DBG: 6: 13465: RIP 1: Receive
response from 10.0.12.1 on GigabitEthernet0/0/0
Sep 13 2013 11:07:20.974.3-05:13 R2 RIP/7/DBG: 6: 13476: Packet: Version 1, Cmd
response, Length 24
Sep 13 2013 11:07:20.974.4-05:13 R2 RIP/7/DBG: 6: 13527: Dest 1.0.0.0, Cost 1
Sep 13 2013 11:07:20.974.5-05:13 R2 RIP/7/DBG: 6: 2688: RIP 1: Ignoring packet.
This version is not configured.
Refer to the debug output. Following configuration of R2, the administrator discovers
that the behavior is not as expected and performs debugging. Based on the output
from the debug, what is the source of the problem?
<choice ident=A> R2 has configured an ACL to block the route to network 1.0.0.0
<choice ident=B> R2 has enabled split horizon.
<choice ident=C> R1 is using authentication, however R2 is not.
<choice ident=D> R2 is operating using RIPv2, while R1 is using RIPv1.
]
item 4.3.3.3
minnumber =2
maxnumber =2
presentation [
Refer to the graphic. An administrator has configed RIPv2 in the two routers shows in
the figure. What will happen after configuring the following commands:
[RTA-Serial0/0/1]rip output
[RTA-rip-1]silent-interface s0/0/1
(Two Answers)
<choice ident=A>RTA will have the route learned from the RTB
<choice ident=B> RTB will have the route learn from the RTA
<choice ident=C>RTA will have no neighbor relationship with RTB
<choice ident=D> RTB will have no neighbor relationship with RTB
2017-1-24
44 , 91
]
item 4.3.3.4
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements about a designated port working in RIPv2 multicast
mode are true? (Select 3 Answers)
<choice ident="A">The port receives only RIPv2 multicast packets.
<choice ident="B">The port does not receive RIPv1 broadcast packets.
<choice ident="C">The port does not receive RIPv2 broadcast packets.
<choice ident="D">The port receives only RIPv1 multicast packets.
]
item 4.4.1.1
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements regarding the router ID in OSPF are incorrect?
(Select 3 Answers)
<choice ident="A">The router IDs of OSPF routers in the same area must be the
same, but can be different in different areas.
<choice ident="B">The router ID must be the IP address of an OSPF router interface.
<choice ident="C">The router ID must be configured manually.
<choice ident="D"> A router running OSPF must have a router ID for it to operate
properly.
]
item 4.4.1.2
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements regarding Designated Routers in OSPF are
correct? (Select 3 Answers)
<choice ident="A">DR is elected by all the routers in the same network segment.
<choice ident="B">If the priorities of two routers are different, the router with the
lower priority will be elected as DR.
<choice ident="C">If the priorities of two routers are equal, the router with the higher
Router ID will be elected as DR.
<choice ident="D">DR and BDR must be adjacent.
]
item 4.4.1.3
2017-1-24
45 , 91
presentation [
On the VRP platform, which of the following commands is used to configure the
Router ID of a router as 1.1.1.1?
<choice ident="A"><Huawei>router id 1.1.1.1
<choice ident="B">[Huawei]router id 1.1.1.1
<choice ident="C">[Huawei]router-id 1.1.1.1
<choice ident="D">[Huawei]router id 1.1.1.1 255.255.255.255
]
item 4.4.1.4
presentation [
Which of the following OSPF versions is specific to IPv6?
<choice ident="A">OSPFv1
<choice ident="B">OSPFv2
<choice ident="C">OSPFv3
<choice ident="D">OSPFv4
]
item 4.4.1.5
presentation [
The administrator wishes to configure OSPF on a router in the network, however the
router has no loopback interface. Which value will be used as the router ID?
<choice ident=A> The lowest IP address of the routers active interfaces.
<choice ident=B> The highest IP address of the routers active interfaces.
<choice ident=C> The IP address of the management interface
<choice ident=D> The priority value of the router.
]
item 4.4.1.6
minnumber = 3
maxnumber = 3
presentation [
An administrator of a company supporting a large enterprise network wishes to
implement OSPF on the network as opposed to RIP. Which of the following points
should the administrator use to support his reasoning for this change? (Three
Answers)
<choice ident=A> OSPF has no hop count limitation
<choice ident=B> OSPF has a lower routing update overhead
<choice ident=C> OSPF has a simpler configuration.
<choice ident=D> OSPF supports faster convergence.
]
item 4.4.1.7
correct-response = "B,C,D"
minnumber = 3
2017-1-24
46 , 91
maxnumber = 3
presentation [
Which of the following statements regarding single area OSPF are correct? (Three
Answers)
<choice ident=A>An IP address needs to be configured on a loopback interface of
each router before configuring an OSPF area.
<choice ident=B>The value of an area can be from 0.0.0.0 to 255.255.255.255.
<choice ident=C>A single area can be configured using any supported area
number.
<choice ident=D>All of the links of the network need to be advertised in Area 0.
]
item 4.4.1.8
minnumber = 2
maxnumber = 2
presentation [
10.0.1.0/24 O_ASE 150 2
D 10.0.23.3
Serial2/0/0
Refer to the display output. Which of the following statements regarding route shown
are true? (Two Answers)
<choice ident=A> The address 10.0.23.3 has been configured on the peers serial
2/0/0 interface.
<choice ident=B> The route preference has been changed by the adminstrator.
<choice ident=C> The metric for the route 10.0.1.0 indicates that two hops are
needed.
<choice ident=D> The route has been learned via the OSPF protocol.
]
item 4.4.2.1
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements regarding link-state database and routing-table of
a single OSPF area are correct? (Select 2 Answers)
<choice ident="A">The link-state databases that all routers build are identical.
<choice ident="B">The link-state databases that all routers build are different.
<choice ident="C">The routing-tables that all routers calculate are different.
<choice ident="D">The routing-tables that all routers calculate are identical.
]
item 4.4.2.2
minnumber = 3
maxnumber = 3
presentation [
Which of the following steps are necessary to configure OSPF on a Huawei router?
(Select 3 Answers)
2017-1-24
47 , 91
<choice ident="A">Configuration of a router ID

<choice ident="B">Enabling of an OSPF process
<choice ident="C">Specifying an OSPF area
<choice ident="D">Configuration of the network segments within each area
]
item 4.4.2.3
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements regarding the DR in an OSPF network are correct?
(Select 2 Answers)
<choice ident="A">There must be at least one DR in an OSPF area.
<choice ident="B">A DR must be elected among the routers through the negotiations
that are defined by OSPF protocol.
<choice ident="C">Only the router with highest priority will be elected as DR.
<choice ident="D">Only NBMA or Broadcast networks need to elect DR
]
item 4.4.2.4
minnumber = 2
maxnumber = 2
presentation [
Which of the following VRP commands can be used to enter area 0 view? (Select 2
Answers)
<choice ident="A">[Huawei]ospf area 0
<choice ident="B">[Huawei-ospf-1]area 0
<choice ident="C">[Huawei-ospf-1]area 0.0.0.0
<choice ident="D">[Huawei-ospf-1]area 0 enable
]
item 4.4.2.5
presentation [
Which of the following commands is used to display the OSPF neighbor relationship
establishment?
<choice ident="A">display ospf neighbor
<choice ident="B">display ospf brief
<choice ident="C">display ospf peer
<choice ident="D">display ospf interface
]
item 4.4.2.6
minnumber = 2
maxnumber = 2
2017-1-24
48 , 91
presentation [
With what kind of routers does a DRother router exchange link state information and
route information? (Select 2 Answers)
<choice ident="A">DR
<choice ident="B">BDR
<choice ident="C">DRother
<choice ident="D">All OSPF neighbors
]
item 4.4.2.7
presentation [
An OSPF area is a collection of a group of routers and networks. OSPF defines that
routers that have the same ( ) belong to the same OSPF area.
<choice ident="A">neighbors
<choice ident="B">LSDB
<choice ident="C">LSA
<choice ident="D">adjacency
]
item 4.4.2.8
minnumber = 2
maxnumber = 2
presentation [
Which of the following statements about router IDs are true? (Select 2 Answers)
<choice ident="A">The routers contained in the same LSDB have the same router
ID.
<choice ident="B">Each router in an OSPF network must have a unique router ID.
<choice ident="C">Two routers in different OSPF areas can have the same router ID.
<choice ident="D">A router ID is expressed in a 32-bit dotted decimal format.
]
item 4.4.2.9
presentation [
OSPF allows for multiple processes. By default, OSPF selects a process whose
number is ( ).
<choice ident="A">0
<choice ident="B">1
<choice ident="C">10
<choice ident="D">100
]
item 4.4.2.10
presentation [
Two routers have established a point-to-point network using PPP. The administrator
has configured the routers to run OSPF in the same area with the same router ID,
2017-1-24
49 , 91
what will behavior will occur as a result of the configuration?

<choice ident=A> The routers will build a neighbor relationship even though both
routers are using the same router ID.
<choice ident=B> VRP will notify of a router ID conflict between the two routers.
<choice ident=C> The routers will build an adjacency even though both routers are
using the same router ID.
<choice ident=D> The routers will not send hello packets to each other because
they are using the same router ID.
]
item 4.4.2.11
correct-response = " D"
presentation [
After checking the OSPF neighbor state, the administrator discovers that the router
has established a TWO-WAY state with the peering router. What can be understood
from this information? (Two Answers)
<choice ident=A> The routers are configured using the same process ID
<choice ident=B> The routers are configured using the same area ID
<choice ident=C> The routers are configured using wrong router ID
<choice ident=D> The routers are considered DROthers in a broadcast network.
]
item 4.4.2.12
minnumber =2
maxnumber =2
presentation [
Refer to the graphic. An administrator has configured OSPF on the two routers,
following which he then implements the command silent-interface s0/0/1 on RTA.
What effect will this command have on the network? (Two Answers)
<choice ident=A> The link information advertised by RTB will be maintained in the
Link State Database of RTA.
<choice ident=B> The OSPF neighbor relationship will fail between two routers.
<choice ident=C> The configuration will not affect the OSPF neighbor relationship
between the two routers.
<choice ident=D> The link information advertised by RTB will no longer be
maintained in the Link State Database of RTA.
]
item 4.4.3.1
correct-response = "B,C
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. Which statements correctly explains the forwarding behavior
between RTA and RTE? (Two Answers)
<choice ident=A>When the network uses OSPF, data will be forwarded along the
path via S1/0/0
2017-1-24
50 , 91
<choice ident=B> When the network uses RIPv2, data will be forwarded along the
path via S1/0/0.
<choice ident=C> When the network uses OSPF, data will be forwarded along the
path from via E0/0/1.
<choice ident=D> When the network uses RIPv2, data will be forwarded along the
path via S2/0/0.
]
item 4.4.3.2
minnumber = 2
maxnumber = 2
presentation [
What functions does a Hello packet of OSPF implement? (Select 2 Answers)
<choice ident="A">Neighbor discovery
<choice ident="B">Deletion of unreachable neighbors.
<choice ident="C">Maintaining of neighbor relationships.
<choice ident="D">Negotiation of parameters among adjacent ports.
]
item 4.4.3.3
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements about the information contained in a Database
Description packet are true? (Select 3 Answers)
<choice ident="A">A Database Description packet contains all information about
each LSA.
<choice ident="B">A Database Description packet contains only the header of an
LSA.
<choice ident="C">The header of an LSA is the unique identifier of the LSA.
<choice ident="D">The header of an LSA is only a small portion of all the data of the
LSA.
]
item 5.1.1.1
presentation [
An end system is unable to communicate with a DHCP server following the startup
process. Which IP address may be used by the client?
<choice ident=A>0.0.0.0
<choice ident=B>127.0.0.1
<choice ident=C>169.254.2.33
<choice ident=D>255.255.255.255
]
item 5.1.1.2
2017-1-24
51 , 91
presentation [
[Huawei]ip pool pool1
Info: It's successful to create an IP address pool.
[Huawei-ip-pool-pool1]network 10.10.10.0 mask 255.255.255.0
[Huawei-ip-pool-pool1]gateway-list 10.10.10.1
Refer to the configuration output. The administrator wishes to configure the DHCP
server pool in order to assign an IP address to the customers terminal device. Which
command should be included in the configuration to provide the minimal lease period
for IP addresses?
<choice ident=A>dhcp select relay
<choice ident=B>lease day 1
<choice ident=C>lease 24
<choice ident=D>lease 0
]
item 5.1.1.3
minnumber =2
maxnumber =2
presentation [
A DHCP server has been established in the enterprise network. After the client has
obtained an IP address from the DHCP server, the user decided to modify the IP
address manually. In what way may this affect the enterprise network? (Two
Answers).
<choice ident=A> The client may experience an IP address conflict.
<choice ident=B> The client may access the network normally.
<choice ident=C> The clients interface connection will shutdown.
<choice ident=D> The client will associate with another DHCP server.
]
item 5.1.1.4
presentation [
Refer to the graphic. Two switches have been connected as shown and both support
STP. The administrator has configured switch A as a DHCP server and set interface
VLANIF1 of switch B to obtain an IP address from switch A. A link failure occurs on
port interface G0/0/1 of switch B. What action will occur as a result?
<choice ident=A> The two switches will be unable to communicate.
<choice ident=B> Switch B will send a DHCP Discovery message to obtain a new
IP address.
<choice ident=C>Swich B will continue to use the IP address obtained from Switch
A.
<choice ident=D> Switch B will send a DHCP Release message to release the IP
address.
]
2017-1-24
52 , 91
item 5.1.2.1
minnumber =3
maxnumber =3
presentation [
A DHCP server in the enterprise network is being used to allocated IP addresses to
hosts. An administrator discovers however that some hosts are obtaining IP
addresses outside of the scope of the DHCP servers address pool. What are the
possible reasons for this? (Three Answers).
<choice ident=A> Another DHCP server exists in the network and is allocating IP
addresses to hosts that happen to be within a closer proximity than the authorized
DHCP server.
<choice ident=B>The hosts were unable to discover a DHCP server and therefore
generated their own address in the 169.254.0.0 address range.
<choice ident=C>The hosts were unable to discover a DHCP server and therefore
generated their own address in the 127.254.0.0 address range.
<choice ident=D>All addresses from the DHCP pool have been assigned.
]
item 5.1.2.2
presentation [
[Router] ip pool pool1
[Router-ip-pool-pool1] network 10.10.10.0 mask 255.255.255.0
[Router-ip-pool-pool1] gateway-list 10.10.10.1
[Router-ip-pool-pool1] quit
[Router] ip pool pool2
[Router-ip-pool-pool2] network 10.20.20.0 mask 255.255.255.0
[Router-ip-pool-pool2] gateway-list 10.20.20.1
[Router-ip-pool-pool2] quit
[Router] interface GigabitEthernet 0/0/1
[Router-GigabitEthernet0/0/1] ip address 10.10.10.1 24
[Router-GigabitEthernet0/0/1] dhcp select global
Refer to the configuration output. Following configuration, a host is connected to the
interface Gigabit Ethernet 0/0/1 of the router. Which IP address will the client obtain?
<choice ident=A> An IP address from network 10.10.10.0/24 will be assigned.
<choice ident=B> An IP address from network 10.20.20.0/24 will be assigned.
<choice ident=C> The host will be unable to obtain an IP address.
<choice ident=D> An IP address may be assigned from either 10.10.10.0/24 or
10.20.20.0/24.
]
item 5.1.2.3
presentation [
The IP addresses of clients in the network are deployed via a DHCP server. When a
host reboots, which message will the host first send to the DHCP server?
<choice ident=A> DHCP DISCOVER
2017-1-24
53 , 91
<choice ident=B> DHCP REQUEST

<choice ident=C> DHCP OFFER
<choice ident=D> DHCP ACK
]
item 5.2.1.1
presentation [
An administrator discovered he/she was unable to use TFTP to transfer files to the
router. Which of the following describes the likely reason for this?
<choice ident=A> The TFTP service had been disabled on the router.
<choice ident=B> TCP port 69 of the server had been blocked.
<choice ident=C> UDP port 69 of the server had been blocked.
<choice ident=D> The username and password had been modified.
]
item 5.2.2.1
presentation [
FTP may be used to upgrade a router's VRP image. Which of the following
transmission modes should be used to achieve this?
<choice ident="A">binary mode
<choice ident="B">ASCII mode
<choice ident="C">byte mode
<choice ident="D">letter mode
]
item 5.3.1.1
presentation [
An administrator wishes to manage the router in the remote branch office, which
method can be used?
<choice ident=A> Telnet
<choice ident=B> FTP
<choice ident=C> Console Connection
<choice ident=D> DHCP
]
item 5.3.1.2
presentation [
Refer to the graphic. The network administrator has configured the router as shown.
Which statement is false?
<choice ident=A>The configuration manages the user login through the console
interface.
<choice ident=B> The user login through vty 0 has the privilege to run level 2
2017-1-24
54 , 91
commands.
<choice ident=C> The user login through telnet has the privilege to run level 2
commands.
<choice ident=D> The configuration manages the telnet user login.
]
item 5.3.1.3
minnumber = 2
maxnumber = 2
presentation [
The administrator cannot use telnet to manage the AR2200. The administrator is able
to verify connectivity to the router and has been informed that other administrators
have no difficulties using telnet. Which statements describe the possible reasons for
this problem? (Two Answers)
<choice ident=A>The users status has been blocked.
<choice ident=B>The users priviledge level has been changed to 0.
<choice ident=C>The user has been deleted.
<choice ident=D>The telnet service in the AR2200 router has been disabled.
]
item 5.3.1.4
correct-response = "A, C"
minnumber = 2
maxnumber = 2
presentation [
A user logged into a VRP supported device through telnet, but when attempting to
configure the device, found that he is unable to use the sytem-view command to
enter the system-view. What are the possible reasons for this? (Two Answers)
<choice ident=A> The devices VTY interface only provides permission for some
telnet users to run the sytem-view command.
<choice ident=B> The users telnet software restricts use of this command.
<choice ident=C> The users privilege level is lower than the level associated with
the system-view command.
<choice ident=D> The system-view command privilege level is lower than the level
associated with the user.
]
item 5.3.1.5
correct-response = "A,B,C"
minnumber = 3
maxnumber = 3
presentation [
An administrator currently manages AR2200 devices in the network through a single
password, however the company wishes to introduce another two administrators and
provide unique user credentials and privilege levels for telnet access to the network
devices. What action can be taken? (Three Anwsers)
<choice ident=A> Configure three users under the AAA-view, and assign each a
different password.
<choice ident=B> The authentication mode must be changed to AAA.
<choice ident=C> Each administrator must be assigned a privilege level.
2017-1-24
55 , 91
<choice ident=D> A public IP address must be assigned to each user for telnet
access.
]
item 5.3.2.1
minnumber = 3
maxnumber = 3
presentation [
Which of the following authentication methods are supported for Telnet users?
(Select 3 Answers)
<choice ident="A">Password authentication
<choice ident="B">AAA local authentication
<choice ident="C">MD5 authentication
<choice ident="D">No authentication
]
item 5.3.2.2
presentation [
The users who log on the router through Telnet are not permitted to configure IP
address. What is the possible reason?
<choice ident="A">Communication failures occur between the user and the router.
<choice ident="B">The authentication mode of Telnet is set incorrectly.
<choice ident="C">Privilege level of Telnet is set incorrectly.
<choice ident="D">SNMP parameters are set incorrectly.
]
item 6.1.1.1
correct-response = "A,B,C
minnumber = 3
maxnumber =3
presentation [
The network administrator has decided to configure link aggregation in the enterprise
network. Which of the following represent advantages of link aggregation? (Three
Answers)
<choice ident=A> Load balancing.
<choice ident=B> Improved bandwidth.
<choice ident=C> Enhanced reliability.
<choice ident=D> Improved security.
]
item 6.1.1.2
presentation [
Refer to the graphic. The network administrator wishes to aggregate the two links as
member interfaces of Eth-trunk 1. Which statement is correct?
2017-1-24
56 , 91
<choice ident=A>The interfaces will be aggregated with load balancing.

<choice ident=B>The interfaces will be aggregated, but only interface GE0/0/1 will
send data flow.
<choice ident=C>The interfaces will be aggregated, but the Eth-trunk will not be
active.
<choice ident=D>The interfaces cannot be aggregated.
]
item 6.1.1.3
presentation [
What is the maximum number of member interfaces supported by a single EthTrunk?
<choice ident=A>6.
<choice ident=B>8.
<choice ident=C>10.
<choice ident=D>12.
]
item 6.1.2.1
presentation [
The Eth-Trunk frame forwarding mechanism used to prevent changes in the data
sequence forwards frames based on which of the following parameters?
<choice ident=A> The same source or destination IP address
<choice ident=B> The same source or destination MAC address.
<choice ident=C> The same protocol type.
<choice ident=D> The same source or destination port number.
]
item 6.1.2.2
presentation [
In Layer 2 mode, the transmission rate of an Eth-Trunk interface is determined by
which of the following?
<choice ident=A> Maximum number of Up member links
<choice ident=B> Minimum number of Up member links
<choice ident=C> Number of Up member interfaces
<choice ident=D> Number of interfaces.
]
item 6.1.2.3
presentation [
The network administrator wishes to forward data over an Eth-trunk, however
associated member interfaces operate at different rates. In terms of the resulting
behavior, which of the following is true?
<choice ident=A> The two switches will not be able to communicate.
2017-1-24
57 , 91
<choice ident=B> The higher rate member interfaces may incur packet loss.
<choice ident=C> The Eth-Trunk will work normally.
<choice ident=D> The lower rate member interfaces may incur packet loss.
]
item 6.1.2.4
presentation [
The network administrator attempts to add interface G0/0/1 on Switch A to Eth-trunk
1, however the command fails. Which of the following may cause this?
<choice ident=A> The interface is operating in half-duplex mode.
<choice ident=B> The interface has been shutdown.
<choice ident=C> The interface is already associated with another Eth-trunk.
<choice ident=D> The interface is an access port.
]
item 6.1.3.1
presentation [
In port aggregation, multiple ports are aggregated to form a port aggregation group
so that all the member ports in the group share the outgoing/incoming load. At which
layer is port aggregation implemented?
<choice ident="A">Physical Layer
<choice ident="B">Data Link Layer
<choice ident="C">Network Layer
<choice ident="D">Transport Layer
]
item 6.1.3.2
minnumber = 3
maxnumber = 3
presentation [
What benefits does port aggregation yield? (Select 3 Answers)
<choice ident="A">Improves link bandwidth
<choice ident="B">Implements load sharing
<choice ident="C">Improves network reliability
<choice ident="D">Facilitates data copy for analysis
]
item 6.2.1.1
presentation [
Refer to the graphic.Which of the following statements are correct? (Two Answers)
<choice ident=A> A single collision domain exists between RTA and SWC.
<choice ident=B> A single broadcast domain exists between SWA and SWB.
2017-1-24
58 , 91
<choice ident=C> A single collision domain exists between SWA and SWC.
<choice ident=D> A single broadcast domain exists between SWA and SWC.
]
item 6.2.1.2
presentation [
A network administrator wishes to implement VLAN 10 to isolate certain users. It is
common however for these users to often change their physical location. Which of
the following VLAN implementations should be used?
<choice ident=A> Port based VLAN assignment.
<choice ident=B> Protocol based VLAN assignment
<choice ident=C> MAC based VLAN assignment.
<choice ident=D> IP subnet based VLAN assignment.
]
item 6.2.1.3
presentation [
A switch receives a VLAN tagged frame, but the destination MAC address cant be
found in the switchs MAC address table, how will the switch react?
<choice ident=A> The switch will broadcast this frame to all ports.
<choice ident=B> The switch will broadcast this frame to all ports in this VLAN.
<choice ident=C> The switch will broadcast this frame to all access ports in this
VLAN.
<choice ident=D> The switch will discard this frame.
]
item 6.2.1.4
presentation [
which of the following statements regarding VLAN configuration is correct?
<choice ident=A> VLAN 1 can be deleted from the switch.
<choice ident=B> VLAN 1 can be configured as a voice VLAN.
<choice ident=C> All trunk ports allow VLAN 1 to pass by default.
<choice ident=D> Voice VLANs can use the default VLAN ID.
]
item 6.2.1.5
presentation [
Refer to the graphic. Communication should be established between Host A and Host
B. VLAN 2 has been created on SWA and SWB. The ports connected to the hosts
are access ports and belong to VLAN 2. Port interfaces G0/0/1 on SWA and G0/0/2
on SWB are trunk ports and permit all VLAN to pass. All that remains is for the
administrator to configure SWC. What should be be configured in order to achieve
the task?
<choice ident=A> The administrator needs only to create VLAN 2 on SWC.
2017-1-24
59 , 91
<choice ident=B> The administrator must set G0/0/1 as a trunk port and permit
VLAN2.
<choice ident=C> The administrator must set both G0/0/1 and G0/0/2 as trunk ports
and permit VLAN2
<choice ident=D> The administrator must create VLAN 2 and set both G0/0/1 and
G0/0/2 as trunk ports and permit VLAN2.
]
item 6.2.1.6
presentation [
Which of the following is correct regarding the configuration of the trunk port and
access port on a switch?
<choice ident=A> Access ports can only send untagged frames.
<choice ident=B> Access ports can only send tagged frames.
<choice ident=C> Trunk ports can only send untagged frames.
<choice ident=D> Trunk ports can only send tagged frames.
]
item 6.2.1.7
correct-response = "D
presentation [
How many VLANs are created when using the commands vlan batch 10 20 and
vlan batch 10 to 20?
<choice ident=A> 2 and 2
<choice ident=B> 11 and 11
<choice ident=C> 11 and 2
<choice ident=D> 2 and 11
]
item 6.2.1.8
correct-response = "A,D
minnumber = 2
maxnumber = 2
presentation [
[Huawei-GigabitEthernet0/0/1] port link-type access
[Huawei-GigabitEthernet0/0/1] port default vlan 10
[Huawei-GigabitEthernet0/0/2] port link-type trunk
[Huawei-GigabitEthernet0/0/2] port trunk allow-pass vlan 10
Refer to the configuration output. Which of the following statements regarding the
configuration output are correct? (Two Answers).
<choice ident=A> The PVID on interface GigabitEthernet0/0/1 is 10
<choice ident=B> The PVID on interface GigabitEthernet0/0/1 is 1
<choice ident=C> The PVID on interface GigabitEthernet0/0/2 is 10.
<choice ident=D> The PVID on interface GigabitEthernet0/0/2 is 1
]
item 6.2.1.9
2017-1-24
60 , 91
minnumber = 3
maxnumber = 3
presentation [
On Sx7 series switches, which of the following VLANs can be removed by using
command "undo"? (Select 3 Answers)
<choice ident="A">vlan 1
<choice ident="B">vlan 2
<choice ident="C">vlan 1024
<choice ident="D">vlan 4094
]
item 6.2.1.10
presentation [
A switch is configured with VLAN 3, VLAN 4 and VLAN 5. GVRP is not enabled for
the trunk port. The trunk port then receives a frame with VLAN ID 6. This frame will
be ( ).
<choice ident="A">Flooded to all VLANs
<choice ident="B">Flooded to VLAN 1 only
<choice ident="C">Flooded to all trunk ports
<choice ident="D">Discarded
]
item 6.2.1.11
presentation [
On the VRP platform, what is the function of the "interface vlanif <vlan-id>"
command?
<choice ident="A">It is used to create a VLANIF interface
<choice ident="B">It is used to create a VLANIF interface and enter the VLANIF
interface view
<choice ident="C">It is used to configure a VLAN for a VLANIF interface
<choice ident="D">There is no such command.
]
item 6.2.2.1
presentation [
Refer to the graphic. Interface G0/0/1 on SWA is a hybrid port in tagged mode with a
PVID of 1 for which VLAN 2 is permitted. Interface G0/0/2 on SWB is a trunk port,
with a PVID of 1 for which VLAN is permitted. Which of the following statements is
correct?
<choice ident=A> Host A can send, but cannot receive frames from Host B.
<choice ident=B> Host A cannot send, but can receive frames from Host B.
<choice ident=C> Host A cannot communicate with Host B.
<choice ident=D> Host A can communicate with Host B.
2017-1-24
61 , 91
]
item 6.2.2.2
presentation [
Refer to the graphic. The interfaces on SWA and SWB are configured as shown.
Which of the following statements are correct? (Two Answers)
<choice ident=A> Host B is able to communicate with the server.
<choice ident=B> Host B is able to communicate with Host A.
<choice ident=C> Host B is unable communicate with the server
<choice ident=D> Host B is unable communicate with Host A.
]
item 6.2.2.3
presentation [
Which of the following statements are correct?
<choice ident=A> SWB receives a frame from Host B and inserts a VLAN 3 tag.
<choice ident=B> SWB receives a frame from Host B and inserts a VLAN 2 tag.
<choice ident=C> When Host A communicates with Host B, an untagged frame is
transmitted between SWA and SWB.
<choice ident=D> When Host A communicates with Host B, a tagged frame is
transmitted between SWA and SWB.
]
item 6.2.2.4
presentation [
Which following is correct?
<choice ident=A> Host C can only receive frames from Host A.
<choice ident=B> Host C can only receive frames from Host B.
<choice ident=C> Host C can receive frames from both Host A and Host B.
<choice ident=D> Host B can receive frames from Host C.
]
item 6.2.2.5
presentation [
Refer to the graphic. All port interfaces are trunk ports and permit all VLANs to pass.
GVRP has been enabled on the three switches and configured on all port interfaces,
and VLAN 10 had been created on only SWA. Which of the following statements
regarding the VLAN 10 is incorrect?
<choice ident=A> SWB is aware of VLAN 10.
2017-1-24
62 , 91
<choice ident=B> G0/0/2 on SWB is associated with VLAN 10.

<choice ident=C> SWC is aware of VLAN 10.
<choice ident=D> G0/0/2 on SWC is associated with VLAN 10.
]
item 6.2.2.6
correct-response = "B,D
minnumber = 2
maxnumber = 2
presentation [
#
[Huawei]interface GigabitEthernet0/0/1
[Huawei-GigabitEthernet0/0/1]port link-type trunk
[Huawei-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 to 4094
#
Refer to the configuration output. Which following statements are correct? (Two
Answers).
<choice ident=A> VLAN 1 cannot pass over interface Gigabit Ethernet 0/0/1
<choice ident=B> VLAN 1 can pass over interface interface Gigabit Ethernet 0/0/1
<choice ident=C> Prior to changing the link-type to access, the command undo
port trunk allow-pass vlan all must be used to renew the default configurations.
<choice ident=D> Prior to changing the link-type to access,the command undo port
trunk allow-pass vlan 2 to 4096 must be used to renew the default configurations.
]
item 6.2.2.7
presentation [
A port of the switch belongs to VLAN 5. If VLAN 5 is removed using the command
"undo vlan 5", to which VLAN does this port subsequently belong?
<choice ident="A">VLAN 0
<choice ident="B">VLAN 1
<choice ident="C">VLAN 1023
<choice ident="D">VLAN 1024
]
item 6.2.2.8
presentation [
What action does an access port take in the process of sending VLAN frames?
<choice ident="A">The access port sends tagged frames.
<choice ident="B">The access port strips the VLAN tag and forwards the frame.
<choice ident="C">The access port exchanges the VLAN tag of the inbound and
outbound port of the frame before forwarding the frame.
<choice ident="D">The access port attaches its PVID information to the frame.
]
2017-1-24
63 , 91
item 6.2.2.9
minnumber = 2
maxnumber = 2
presentation [
Which of the following are the features of the default VLAN setting in a switch
configuration? (Select 2 Answers)
<choice ident="A">The default VLAN cannot be deleted manually.
<choice ident="B">By default, the ports on all switches are member ports of a default
VLAN.
<choice ident="C">A default VLAN must be created before a port is allocated to a
VLAN.
<choice ident="D">The IP address configured for a switch is applied only to a
member port in the default VLAN.
]
item 6.2.2.10
presentation [
A port on a switch is configured as a Trunk port. Assume that one host connects to
this Trunk port to access the network. Which of the following operations is
mandatory?
<choice ident="A">Delete all the VLANs on this port in the global view.
<choice ident="B">Delete all the VLANs on this port in the interface view.
<choice ident="C">Disable this port and then enable it again to restore the default
setting of the port.
<choice ident="D">Configure this port as an access port.
]
item 6.2.2.11
presentation [
Which of the following statements regarding the port trunk allow-pass vlan all
command is true?
<choice ident="A">The specified port allows all VLAN IDs to pass through.
<choice ident="B">The peer port connected to this port must have the same port
trunk allow-pass vlan all command configured.
<choice ident="C">The peer device connected to this port can dynamically determine
which VLAN IDs are allowed to pass through.
<choice ident="D">If the port default vlan 3 command is run on the connected remote
device, VLAN 3 will be blocked between the two devices
]
item 6.2.3.1
presentation [
Refer to the graphic. Interface G0/0/2 on SWA is a trunk port with a PVID of 2, and
for which all VLANs are permitted to pass. Interface G0/0/2 on SWB is a trunk port
2017-1-24
64 , 91
with a PVID of 3 for which all VLANs are permitted. Which statement is correct?
<choice ident=A> Host A is able to communicate with Host B
<choice ident=B> Host A is able to communicate with Host C
<choice ident=C> Host A is able to communicate with both Host B and Host C
<choice ident=D> Host A is able to communicate neither Host B nor Host C
]
item 6.2.3.2
presentation [
Refer to the graphic. Interface G0/0/2 on SWA is a trunk port with a PVID of 2 and for
which only VLAN 3 is permitted to pass. Interface G0/0/2 on SWB is a trunk port with
a PVID of 2 for which only VLAN 3 is permitted to pass. Which statement is correct?
<choice ident=A> Host A is able to communicate with Host C
<choice ident=B> Host A is able to communicate with Host D
<choice ident=C> Host B is able to communicate with Host C
<choice ident=D> Host B is able to communicate with Host D
]
item 6.2.3.3
correct-response = "B
presentation [
Refer to the graphic. When Host A communicates with Host C, an untagged frame is
transmitted over the trunk link, but when Host B communicates with Host D, a tagged
VLAN 20 frame is transmitted over the trunk link. With regards to this behavior which
of the following statements is correct?
<choice ident=A>The interface G0/0/2 on SWA does not allow VLAN 10 to pass.
<choice ident=B>The PVID on interface G0/0/2 of SWA is 10
<choice ident=C>The PVID on interface G0/0/2 of SWA is 20
<choice ident=D>The PVID on interface G0/0/2 of SWA is 1
]
item 6.3.2.1
presentation [
Refer to the graphic. VLANs 10 and 20 have been created on both SWA and SWC.
VLAN 10 has been manually created on SWB. SWB has learned VLAN 20 from SWA
and SWC via GVRP, allowing the hosts to belong to different VLANs as shown. If port
interface G0/0/1 on SWB is changed to fixed mode, what will happen?
<choice ident=A> Host A will still be able to communicate with Host C.
<choice ident=B> Host B will still be able to communicate with Host D.
<choice ident=C> Hosts that belong to the same VLAN will still be able to
communicate.
<choice ident=D> All hosts will be unable to communicate with any other host.
]
2017-1-24
65 , 91
item 6.3.2.2
presentation [
Refer to the graphic. VLAN 10 and VLAN 20 has been created on both SWA and
SWC. VLAN 10 has been manually created on SWB. SWB has learned VLAN 20
from SWA and SWC via GVRP, allowing the hosts to belong to different VLANs as
shown. If port interface G0/0/1 on SWB is changed to forbidden mode, what will
happen?
<choice ident=A> Host A will still be able to communicate with Host C.
<choice ident=B> Host B will still be able to communicate with Host D.
<choice ident=C> Hosts that belong to the same VLAN will still be able to
communicate.
<choice ident=D> All hosts will be unable to communicate with any other host.
]
item 6.4.1.1
presentation [
Refer to the graphic. Host A and Host B use VLAN routing to communicate. Which of
the following statements is correct regarding the initial forwarding of a frame by SWA
between Host A and Host B?
<choice ident=A> SWA only performs a lookup of the MAC address table.
<choice ident=B> SWA only performs a lookup of the routing-table
<choice ident=C> SWA first performs a lookup of the MAC address table and then
the routing-table.
<choice ident=D> SWA first performs a lookup of the routing-table then checks the
MAC address table.
]
item 6.4.1.2
presentation [
Refer to the graphic. Host A and Host B use VLAN routing to facilitate
communication. What must be configured on interface G0/0/1.1 of RTA to achieve
this?
<choice ident=A>dot1q termination vid 1
<choice ident=B>dot1q termination vid 10
<choice ident=C>dot1q termination vid 20
<choice ident=D>dot1q termination vid 30
]
item 6.4.1.3
presentation [
2017-1-24
66 , 91
Refer to the graphic.Host A and Host B uses VLAN routing to facilitate

communication. When interface G0/0/1.2 of RTA receives a frame from Host B, what
will RTA do?
<choice ident=A> RTA will immediately forward the frame via interface G0/0/1.1
<choice ident=B> RTA remove the VLAN tag before forwarding the frame.
<choice ident=C> RTA will remove the VLAN tag and add a new tag for VLAN10
<choice ident=D> RTA will discard the frame
]
item 6.4.1.4
correct-response = "C
presentation [
When using a router to enforce VLAN communication, why are sub-interfaces used?
<choice ident=A> Physical interfaces cannot encapsulate 802.1Q tagged frames
<choice ident=B> The sub-interface forwarding speed is faster
<choice ident=C> The use of sub-interfaces can conserve physical interfaces
<choice ident=D> The sub-interface can be configured as access or trunk ports
]
item 6.4.2.1
presentation [
The network administrator creates VLAN 10 and assigns an IP address to VLANIF10.
When using the command display ip interface brief, the administrator finds that
VLANIF10 is down. What should be done to enable VLANIF10?
<choice ident=A> Use the command undo shutdown under the interface view for
VLANIF10.
<choice ident=B> Assign a physical interface that has either an active of inactive
physical state to VLAN 10.
<choice ident=C> Assign only a physical interface that has an active physical state
to VLAN 10.
<choice ident=D> Add an interface that has an active physical state and a trunk port
associated with VLAN 10 .
]
item 6.5.1.1
presentation [
Which of the following WLAN standards support operation in the 5GHz range? (Two
Answers).
<choice ident=A> 802.11a
<choice ident=B> 802.11b
<choice ident=C> 802.11g
<choice ident=D> 802.11n
]
item 6.5.1.2
presentation [
2017-1-24
67 , 91
which of the following standards provide a transmission rate of more than 1Gbps ?
<choice ident=A> 802.11b
<choice ident=B> 802.11g
<choice ident=C> 802.11n
<choice ident=D> 802.11ac
]
item 7.1.1.1
presentation [
Refer to the graphic. On the interface serial 1/0/1 of RTA,the command ip address
unnumbered interface loopback 0 has been configured. Which following statements
are correct? (Two Answers).
<choice ident=A>The IP address of interface serial 1/0/1 is 10.1.1.1/24
<choice ident=B>The IP address of interface serial 1/0/1 is 10.1.1.1/32
<choice ident=C>The route entry 10.1.1.0/24 exists in RTAs routing-table
<choice ident=D>The route entry 10.1.1.0/24 does not exist in RTAs routing-table
]
item 7.1.1.2
presentation [
Refer to the graphic. The link between RTA and RTB is encapsulated using PPP. The
IP addresses of serial 1/0/1 of RTA and serial 1/0/1 of RTB are in different network
segments. Which following is correct? (Two Answers).
<choice ident=A> RTA can ping 10.1.1.2 successfully
<choice ident=B> RTA cannot ping 10.1.1.2
<choice ident=C>The route entry 10.1.1.0/24 exists in the routing-table of RTA
<choice ident=D>The route entry 10.1.1.2/32 exists in the routing-table of RTA
]
item 7.1.1.3
correct-response = "A,C,D"
presentation [
Two routers are connected through serial interfaces and support PPP encapsulation.
Which parameters must be negotiated to establish the PPP connection? (Three
Answers).
<choice ident=A> MRU
<choice ident=B> Authentication password
<choice ident=C> Magic-Number
<choice ident=D> IP address
]
item 7.1.1.4
2017-1-24
68 , 91
presentation [
What are the three protocol components defined by PPP? (Three Answers).
<choice ident=A> Data encapsulation.
<choice ident=B> LCP
<choice ident=C> NCP
<choice ident=D> IPCP
]
item 7.1.1.5
correct-response = "A
presentation [
Two routers are connected via serial interfaces, for which the link-protocol is PPP.
The network administrator wishes to configure PPP authentication to improve
security on this link. Which PPP authentication method provides a more secure
solution?
<choice ident=A> CHAP
<choice ident=B> PAP
<choice ident=C> MD5
<choice ident=D> SSH
]
item 7.1.1.6
presentation [
If PPP authentication fails, which type of packet will be sent to the authenticated peer
by the authenticator?
<choice ident=A> Authenticate-Ack
<choice ident=B> Authenticate-Nak
<choice ident=C> Authenticate-Reject
<choice ident=D> Authenticate-Reply
]
item 7.1.1.7
presentation [
Two routers are connected via serial interfaces and the link-protocol is PPP, but the
MRU of two serial interfaces are different, in PPP LCP negotiated stage, what will
happen?
<choice ident=A>LCP negotiation will fail
<choice ident=B>Negotiation will use the smaller value
<choice ident=C>Negotiation will use the larger value
<choice ident=D>Negotiation will use 1500
]
item 7.1.1.8
presentation [
When using VRP, which of the following commands is used to configure the data link
2017-1-24
69 , 91
layer encapsulation type of a serial interface as HDLC?

<choice ident="A">encapsulation hdlc
<choice ident="B">link-protocol hdlc
<choice ident="C">hdlc enable
<choice ident="D">link-protocol ppp
]
item 7.1.1.9
minnumber = 2
maxnumber = 2
presentation [
PPP is more secure than HDLC because PPP supports authentication protocols such
as ( ). (Select 2 Answers)
<choice ident="A">PAP
<choice ident="B">MD5
<choice ident="C">CHAP
<choice ident="D">SSH
]
item 7.1.1.10
presentation [
When both ends running PPP protocol detect that the physical link is active, the link
state will transit from dead to establish. Which of the following protocols is used to
negotiate the link parameters during this phase?
<choice ident="A">IP
<choice ident="B">DHCP
<choice ident="C">LCP
<choice ident="D">NCP
]
item 7.1.1.11
presentation [
A serial interface of a Huawei router currently using HDLC needs to assign PPP as
the encapsulation protocol. Which of the following commands is required to be
configured at the serial interface view?
<choice ident="A">link-protocol ppp
<choice ident="B">encapsulation ppp
<choice ident="C">enable ppp
<choice ident="D">address ppp
]
item 7.1.1.12
presentation [
When using VRP, which of the following commands is used to configure the PPP
authentication method as PAP?
2017-1-24
70 , 91
<choice ident="A">ppp pap

<choice ident="B">ppp authentication-pap
<choice ident="C">ppp authentication-mode pap
<choice ident="D">ppp pap-authentication
]
item 7.1.1.13
minnumber = 3
maxnumber = 3
presentation [
When configuring the PPP authentication method as PAP, which of the following
operations are necessary? (Select 3 Answers)
<choice ident="A">Add the user name and password of the authenticated party to
the local user list
<choice ident="B">Configure the encapsulation type of the interface connected to the
peer as PPP.
<choice ident="C">Configure PPP authentication method as CHAP
<choice ident="D">On the authenticated party end, configure the user name and
password that are sent to authenticator
]
item 7.1.2.1
presentation [
In the PPP protocol, which of the following encryption algorithms is used by CHAP?
<choice ident="A">DES
<choice ident="B">MD5
<choice ident="C">AES
<choice ident="D">None
]
item 7.1.2.2
presentation [
In order to check if the interface serial 1/0/0 is working in either DCE or DTE mode,
command ( ) is used.
<choice ident="A">display mode serial 1/0/0
<choice ident="B">display controller
<choice ident="C">display interface serial 1/0/0
<choice ident="D">display current-config
]
item 7.1.3.1
presentation [
What is the function of the ip address ppp-negotiate command?
<choice ident="A">Enables the function of requesting for an IP address from the peer
2017-1-24
71 , 91
device.
<choice ident="B">Enables the function of accepting the request for an IP address
from the remote device.
<choice ident="C">Enables the function of statically allocating IP addresses to the
peer.
<choice ident="D">None of the above
]
item 7.2.1.1
presentation [
How is mapping performed on a DTE device in a Frame Relay network?
<choice ident=A>The local DLCI number is mapped to a remote IP address.
<choice ident=B>The local IP address is mapped to a remote DLCI number.
<choice ident=C>The local DLCI number is mapped to a local IP address.
<choice ident=D>The remote DLCI number is mapped to a remote IP address.
]
item 7.2.1.2
presentation [
If Frame Relay implements dynamic address mapping for the PVCwhich protocol
will be used?
<choice ident=A> LMI protocol.
<choice ident=B> ARP protocol.
<choice ident=C> RARP protocol.
<choice ident=D> InARP protocol
]
item 7.2.1.3
correct-response = "A,C
presentation [
Refer to the graphic. Which of the following statements correctly describe the Frame
Relay devices? (Two Answers)
<choice ident=A> RTA is a DTE device.
<choice ident=B> FRA is a DTE device.
<choice ident=C> FRB is a DCE device.
<choice ident=D> The interface on RTA is a DCE interface.
]
item 7.2.1.4
presentation [
Refer to the graphic. RTA and RTB are connected over a Frame Relay network using
a DLCI, as shown. Static mapping is required on RTA. Which of the following
commands will achieve this?
2017-1-24
72 , 91
<choice ident=A> [RTA-Serial1/0/1]fr map ip 172.16.1.1 30

<choice ident=B> [RTA-Serial1/0/1]fr map ip 172.16.1.1 31
<choice ident=C> [RTA-Serial1/0/1]fr map ip 172.16.2.1 30
<choice ident=D> [RTA-Serial1/0/1]fr map ip 172.16.2.1 31
]
item 7.2.1.5
correct-response = "C,D
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. RTA is a DTE device connected to a Frame Relay switch, and
uses dynamic address mapping to establish the PVC. With regards to the
configuration, which of the following commands are not necessary? (Two Answers).
<choice ident=A> [RTA-Serial1/0/1]ip address 172.16.1.1 24
<choice ident=B> [RTA-Serial1/0/1]link-protocol FR
<choice ident=C> [RTA-Serial1/0/1]fr interface-type dte
<choice ident=D> [RTA-Serial1/0/1]fr inarp
]
item 7.2.1.6
presentation [
Which command should be used to check the mapping between protocol addresses
and frame relay addresses?
<choice ident=A>display fr interface
<choice ident=B>display fr map-info
<choice ident=C>display fr inarp-info
<choice ident=D>display interface brief
]
item 7.2.1.7
presentation [
Which of the following protocols is used in Frame Relay to map the address to DLCI
dynamically?
<choice ident="A">ARP protocol
<choice ident="B">RARP protocol
<choice ident="C">InARP protocol
<choice ident="D">Map protocol
]
item 7.2.1.8
minnumber = 2
maxnumber = 2
presentation [
Which of the following parameters must be specified when configuring static mapping
2017-1-24
73 , 91
for Frame Relay network? (Select 2 Answers)

<choice ident="A">Local DLCI
<choice ident="B">Remote DLCI
<choice ident="C">Local network layer protocol address
<choice ident="D">Remote network layer protocol address
]
item 7.2.2.1
minnumber = 3
maxnumber = 3
presentation [
Which of the following regarding Frame Relay DLCI are correct? (Select 3 Answers)
<choice ident="A">DLCI is locally significant
<choice ident="B">DLCI is allocated by DTE
<choice ident="C">The range of DLCI value that can be used is from 16-1007.
<choice ident="D">The same DLCI can be configured on different physical interfaces
]
item 7.2.2.2
presentation [
Which of the following commands is used to enable dynamic address mapping
protocol in the interface encapsulated with Frame Relay?
<choice ident="A">fr inarp
<choice ident="B">fr reverse-arp
<choice ident="C">inverse-arp
<choice ident="D">reverse-arp
]
item 7.2.2.3
presentation [
What is the meaning of 200 in the command "fr map ip 10.1.1.2 200"?
<choice ident="A">remote logical channel ID
<choice ident="B">local DLCI
<choice ident="C">remote interface ID
<choice ident="D">remote node ID
]
item 7.2.2.4
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic.RTA and RTB connect to a Frame Relay switch and use dynamic
address mapping. The command fr map ip 10.0.1.1 32 is then configured on RTB,
2017-1-24
74 , 91
without using the undo inarp command. What will occur as a result? (Two Answers).
<choice ident=A> RTB will be unable to communicate with RTA
<choice ident=B> 10.0.1.1 will still be mapped to DLCI 31 on RTB
<choice ident=C> 10.0.1.1 will still be mapped to DLCI 32 on RTB
<choice ident=D> DLCI 32 will be activated on RTB
]
item 7.2.3.1
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. RTA and RTB are connected to the same Frame Relay switch
and use same DLCI number, which following is correct? (Two Answers).
<choice ident=A> RTA and RTB must be associated with the same PVC
<choice ident=B> RTA and RTB can be associated with different PVCs
<choice ident=C> The DLCI on the different physical interfaces can be the same
<choice ident=D> The DLCI on the different physical interfaces cannot be the same
]
item 7.2.3.2
presentation [
Which of the following commands can be used to display mapping relationship
between network address and DLCI?
<choice ident="A">display fr interface
<choice ident="B">display fr
<choice ident="C">display fr map-info
<choice ident="D">display fr brief
]
item 7.2.3.3
minnumber = 3
maxnumber = 3
presentation [
Which of following may be the reasons that cause Frame Relay PVC to work
abnormally? (Select 3 Answers)
<choice ident="A">Same DLCI number is configured on the same router.
<choice ident="B">LMI type mismatch
<choice ident="C">Frame Relay encapsulation type mismatch
<choice ident="D">Incorrect configuration of the DLCI number
]
item 7.3.1.1
presentation [
2017-1-24
75 , 91
The PPPoE session establishment process can be divided into which stages? (Two
Answers).
<choice ident=A> Discovery stage.
<choice ident=B> DHCP stage
<choice ident=C> PPPoE Session stage
<choice ident=D> PPP connecting stage.
]
item 7.3.1.2
presentation [
To establish multiple PPP point-to-point connections in the Ethernet network, a
PPPoE server establishes connections with multiple PPPoE clients on one Ethernet
port. How does PPPoE differentiate between each connection?
<choice ident=A> MAC address.
<choice ident=B> IP address and MAC address
<choice ident=C> MAC address and ppp-id
<choice ident=D> MAC address and session-id
]
item 7.3.1.3
presentation [
When configuring a router as a PPPoE client, which configuration is not necessary?
<choice ident=A> Configuration of the dialer-rule
<choice ident=B> Configuration of the dialer interface
<choice ident=C> Configuration of an IP address on the dialer interface
<choice ident=D> Configuration of a password on the dialer interface
]
item 7.3.1.4
presentation [
Refer to the graphic. RTA is a PPPoE client, and sends PADI packets to Server A.
Which distribution method is used for sending PADI packets?
<choice ident=A> unicast
<choice ident=B> multicast
<choice ident=C> broadcast
<choice ident=D> anycast
]
item 7.3.1.5
presentation [
Refer to the graphic. RTA is a PPPoE client, and following transmission of PADI,
2017-1-24
76 , 91
Server A responds with PADO packets to RTA. Which distribution method is used for
sending PADO packets?
]
item 7.3.1.6
presentation [
In the PPPoE discovery stage, the PPPoE server assigns a session-id to the PPPoE
client in which packet?
<choice ident=A> PADI
<choice ident=B> PADO
<choice ident=C> PADR
<choice ident=D> PADS
]
item 7.3.1.7
presentation [
Which command can be used to check the PPPoE client session status?
<choice ident=A> display ip interface brief
<choice ident=B> display current-configuration
<choice ident=C> display pppoe-client session packet
<choice ident=D> display pppoe-client session summary
]
item 7.4.1.1
presentation [
A network requires a solution to allow 50 private IP addresses to be translated,
however only a single public address is available for use. Which translation method
can be used to support this requirement?
<choice ident=A> Static NAT.
<choice ident=B> Dynamic NAT
<choice ident=C> Easy-IP
<choice ident=D> NAPT
]
item 7.4.1.2
presentation [
NAPT allows for multiple internal addresses to be mapped to a single public address.
How does NAT distinguish between the different private addresses when mapping to
the same public address.
<choice ident=A> The source MAC address is used.
2017-1-24
77 , 91
<choice ident=B> The destination MAC address is used.

<choice ident=C> The source port number is used.
<choice ident=D> The destination port number is used.
]
item 7.4.1.3
presentation [
Refer to the graphic. Host A is located in a private network. It is required that Host A
not only be capable of routing traffic over the public network, but also that public
users are able to actively communicate with Host A. Which NAT translation method
should be configured on the gateway?
<choice ident=A> Static NAT
<choice ident=B> Dynamic NAT
<choice ident=C> Easy-IP
<choice ident=D> NAPT
]
item 7.4.1.4
presentation [
Refer to the graphic. In the private network, RTA dynamically assigns a public
address from the address pool to hosts without port translation. Host C wishes to
access the public network while pool addresses are assigned to Host A and Host B.
What will occur as a result?
<choice ident=A> The first public address will be allocated to Host C, and Host A
will be forced offline.
<choice ident=B> The last public address will be allocated to Host C, and Host B
will be forced offline.
<choice ident=C> Host C will be unable to forward traffic over the public network.
<choice ident=D> All hosts will have access to the public network through pool
address swapping.
]
item 7.4.1.5
presentation [
Refer to the graphic. A web server in a private network is required to provide HTTP
services to public users. The network administrator is required to configure NAT on
RTA. Which configuration should be used?
<choice ident=A>
[RTA-Serial1/0/1]nat server protocol tcp global 202.10.10.1 www inside 192.168.1.1
8080
<choice ident=B>
[RTA-Serial0/0/1]nat server protocol tcp global 192.168.1.1 www inside 202.10.10.1
8080
<choice ident=C>
2017-1-24
78 , 91
[RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www inside

192.168.1.1 8080
<choice ident=D>
[RTA- Gigabitethernet0/0/1]nat server protocol tcp global 192.168.1.1 www inside
202.10.10.1 8080
]
item 7.4.1.6
presentation [
Refer to the graphic. The network administrator needs to configure static NAT on
RTA, in order to allow Host A to communicate with Host C. Which command is
correct?
<choice ident=A> [RTA-Serial1/0/1]nat outbound 200.1.1.10
<choice ident=B> [RTA-Serial1/0/1]nat static global 200.1.1.10 inside 192.168.1.0
<choice ident=C> [RTA-Serial1/0/1]nat static global 192.168.1.1 inside 200.1.1.10 .
<choice ident=D> [RTA-Serial1/0/1]nat static global 200.1.1.10 inside 192.168.1.1
]
item 7.4.1.7
presentation [
[RTA-GigabitEthernet0/0/0]nat outbound 2000 address-group 1
Refer to the configuration output. What does the value 2000 refer to?
<choice ident=A> It represents the ACL number.
<choice ident=B> It represents the NAT number.
<choice ident=C> It represents the translated port number .
<choice ident=D> It represents the number of bytes that can be translated before
the address is returned to the public address pool.
]
item 7.4.1.8
presentation [
NAPT uses the same public address but different port numbers to translate private
addresses. Which statement regarding the port number is correct?
<choice ident=A> It is necessary to configure port number mapping manually.
<choice ident=B> It is only necessary to configure the port number range.
<choice ident=C> It is not necessary to configure port numbers.
<choice ident=D> An access control list is needed to assign port numbers.
]
item 7.4.1.9
minnumber = 2
maxnumber = 2
presentation [
A configured internal host of a private network wishes to access the internet. What
2017-1-24
79 , 91
must be configured on the enterprise networks edge router in order to achieve this?
(Two Answers)
<choice ident=A> NAT EasyIP
<choice ident=B> DHCP
<choice ident=C> BGP
<choice ident=D> Default route
]
item 7.4.1.10
minnumber = 3
maxnumber = 3
presentation [
Which of the following statements are correct about NAT? (Select 3 Answers)
<choice ident="A">NAT is the abbreviation for "Network Address Translation"
<choice ident="B">NAT is used for translation between private and public network
addresss.
<choice ident="C">When hosts inside a private network access the outside network,
NAT is not required.
<choice ident="D">NAT provides an effective way to solve the problem of insufficient
IP addresses.
]
item 7.4.1.11
presentation [
Which of the following technologies can allow a host with IP address 10.0.0.1 to
access the internet?
<choice ident="A">Static route
<choice ident="B">Dynamic route
<choice ident="C">Route import
<choice ident="D">NAT
item 7.4.2.1
presentation [
Which of the following items can be translated by NAPT?
<choice ident="A">MAC address + port number
<choice ident="B">IP address + port number
<choice ident="C">Only MAC address
<choice ident="D">Only IP address
]
item 8.1.1.1
presentation [
What of the following statements is correct regarding access control list types and
ranges?
2017-1-24
80 , 91
<choice ident=A> A basic ACL value ranges from 1000-2999

<choice ident=B> An advanced ACL value ranges from 3000-4000
<choice ident=C> A layer 2 ACL value ranges from 4000-4999
<choice ident=D> An interface ACL value ranges 1000-2000
]
item 8.1.1.2
presentation [
Which of the following parameters is not used by Advanced ACL?
<choice ident=A> source interface
<choice ident=B> destination port number
<choice ident=C> protocol number
<choice ident=D> time-range
]
item 8.1.1.3
presentation [
[RTA]acl 2001
[RTA-acl-basic-2001]rule permit source 10.0.1.0 0.0.0.255
[RTA-acl-basic-2001]rule deny source 10.0.1.0 0.0.0.255
Refer to the configuration output. Which of the following statements regarding ACL
2001 is correct?
<choice ident=A> Packets from network 10.0.1.0/24 network will be denied.
<choice ident=B> Packets from network 10.0.1.0/24 network will be permitted.
<choice ident=C> Packets destined for network 10.0.1.0/24 will be denied.
<choice ident=D> Packets destined for network 10.0.1.0/24 will be permitted.
]
item 8.1.1.4
correct-response = "B,D
minnumber = 2
maxnumber = 2
presentation [
:
[RTA]acl 2002
[RTA-acl-basic-2002]rule permit source 20.1.1.1 0
[RTA-acl-basic-2002]rule permit source 30.1.1.1 0
Refer to the configuration output. A network administrator configured the ACL on
router RTA, as shown. Which of the following statements regarding the rule order are
correct? (Two Answers).
<choice ident=A> The rule-number of the first rule is 1
<choice ident=B> The rule-number of the first rule is 5
2017-1-24
81 , 91
<choice ident=C> The rule-number of the second rule is 2

<choice ident=D> The rule-number of the second rule is 10
]
item 8.1.1.5
minnumber = 2
maxnumber = 2
presentation [
Refer to the graphic. The network administrator has configured ACL 2000 to filter
packets on RTA, as shown. Which of following statements regarding the subsequent
behavior are correct? (Two Answers).
<choice ident=A> RTA will forward packets received from Host A.
<choice ident=B> RTA will drop packets received from Host A.
<choice ident=C> RTA will forward packets received from Host B.
<choice ident=D> RTA will drop packets received from Host B.
]
item 8.1.1.6
presentation [
Refer to the graphic. The network administrator wishes to deny Host A access to the
HTTP server but allow access to all other servers. Which of the following ACL rules
will achieve this?
<choice ident=A> rule deny tcp source 10.1.1.1 0 destination 202.100.1.12 0.0.0.0
destination-port eq 21
<choice ident=B> rule deny tcp source 10.1.1.1 0 destination 202.100.1.12 0.0.0.0
<choice ident=C> rule deny udp source 10.1.1.1 0 destination 202.100.1.12 0.0.0.0
<choice ident=D> rule deny udp source 10.1.1.1 0 destination 202.100.1.12 0.0.0.0
]
item 8.1.2.1
correct-response = "A,B,C"
minnumber = 3
maxnumber = 3
presentation [
Following a failure of services in the network, an administrator discovered that the
configuration in one of the enterprise routers had been changed. What actions can
be taken by the administrator to prevent further changes? (Three Answers)
<choice ident=A> The administrator should limit access by setting the login privilege
of users to 0.
2017-1-24
82 , 91
<choice ident=B>The administrator should configure AAA to manage user

authorization on the router.
<choice ident=C>The administrator should configure an ACL to allow only the
administrator to manage the router.
<choice ident=D>The administrator should configure port-security on the router
]
item 8.1.2.2
presentation [
[RTA]acl 2001
[RTA-acl-basic-2001]rule 20 permit source 20.1.1.0 0.0.0.255
[RTA-acl-basic-2001]rule 10 deny source 20.1.1.0 0.0.0.255
Refer to the configuration output. Which of the following statements is correct
regarding the configuration of the ACL on RTA?
<choice ident=A> Packets from network 20.1.1.0/24 network will be denied.
<choice ident=B> Packets from network 20.1.1.0/24 network will be permitted.
<choice ident=C> Packets destined for network 20.1.1.0/24 will be denied.
<choice ident=D> Packets destined for network 20.1.1.0/24 will be permitted.
]
item 8.1.2.3
minnumber = 2
maxnumber = 2
presentation [
[RTA]acl 2001
Refer to the configuration output. Which of the following statements are correct
regarding the configuration of the ACL on RTA? (Two Answers).
<choice ident=A> Packets from network 172.16.1.1/32 will be denied.
<choice ident=B> Packets from network 172.16.1.0/24 will be denied.
<choice ident=C> Packets from network 172.17.1.0/24 will be denied.
<choice ident=D> Packets from network 172.18.0.0/16 will be denied.
]
item 8.2.1.1
presentation [
What is the default authentication mode for the default_admin domain?
<choice ident=A> None
<choice ident=B> Local
<choice ident=C> Radius
<choice ident=D> 802.1X
2017-1-24
83 , 91
item 8.2.1.2
minnumber = 3
maxnumber =3
presentation [
Which authentication modes does AAA support? (Three Answers).
<choice ident=A> None
<choice ident=B> Local
<choice ident=C> Radius
<choice ident=D> 802.1X
]
item 8.2.1.3
presentation [
How many domains can be configured on a Huawei router?
<choice ident=A> 30
<choice ident=B> 31
<choice ident=C> 32
<choice ident=D> 33
]
item 8.2.2.1
presentation [
An authenticator router has been configured with two domains named Area1 and
Area2, following which a user is created with the username huawei and the
password hello for authentication. Which domain does this user belongs to?
<choice ident=A> Area1 domain
<choice ident=B> Area2 domain
<choice ident=C> default domain
<choice ident=D> default_admin domain
]
item 8.2.2.2
presentation [
[RTA]aaa
[RTA-aaa]domain huawei
[RTA-aaa-domain-huawei]authentication-scheme au1
[RTA-aaa-domain-huawei]authentication-scheme au2
Refer to the configuration output. RTA has been configured using AAA as shown, and
associated with the huawei domain. For users in the huawei domain, which
authentication-scheme will be used?
<choice ident=A> au1
<choice ident=B> au2
<choice ident=C> au1 will be used. When au1 is deleted, users will use au2
2017-1-24
84 , 91
<choice ident=D> au2 will be used. When au2 is deleted, users will use au1
]
item 8.2.3.1
correct-response = "A,B,D
minnumber = 3
maxnumber =3
presentation [
A user accesses a server supporting AAA, for which the authorization mode on the
AAA server has been configured using the command authorization-mode hwtacacs
if-authenticated. Which of the following statements regarding this command are
true? (Three Answers).
<choice ident=A> If the hwtacacs server fails to respond, the user will be
authenticated using local authentication.
<choice ident=B> If the hwtacacs server fails to respond, the user will be
authenticated using remote authentication.
<choice ident=C> If the hwtacacs server fails to respond, the user will bypass
authentication.
<choice ident=D> The hwtacacs server will authorize the user.
]
item 8.3.1.1
presentation [
Refer to the graphic. Packet encapsulation in the IPsec architecture is performed as
shown. Which IPsec mode is being used to encapsulate the packet?
<choice ident=A> normal mode
<choice ident=B> tranport mode
<choice ident=C> tunnel mode
<choice ident=D> this encapsulation is wrong
]
item 8.3.1.2
presentation [
Refer to the graphic. IPsec VPN uses ESP to encrypt which fields ?
<choice ident=A> TCP, Data and ESP Trailer
<choice ident=B> ESP, TCP and Data
<choice ident=C> ESP, TCP, Data and ESP Trailer
<choice ident=D> ESP, TCP, Data, ESP Trailer and ESP Auth
]
item 8.3.1.3
correct-response = "C,D
minnumber = 2
maxnumber =2
2017-1-24
85 , 91
presentation [
Refer to the graphic. In order to improve security, the two hosts use IPsec VPN to
transmit data. Which IPsec mode and protocol can be used to hide the hosts IP
address? (Two Answers).
<choice ident=A> AH
<choice ident=B> transport mode
<choice ident=C> tunnel mode
<choice ident=D> ESP
]
item 8.3.1.4
presentation [
If AH and ESP are both required to protect data streams between IPsec peers, how
many Security Associations (SA) are required in total?
<choice ident=A> 1
<choice ident=B> 2
<choice ident=C> 3
<choice ident=D> 4
]
item 8.3.1.5
presentation [
Refer to the graphic. The data is transmitted using IPsec tunnel mode. The fields of
which headers will be authenticated?
<choice ident=A> TCP and Data
<choice ident=B> Origin IP, TCP and Data
<choice ident=C> AH, Origin IP, TCP and Data
<choice ident=D> The fields of all headers
]
item 8.3.1.6
presentation [
Two routers establish an IPsec tunnel, which of the following does not need to be the
same on both peering devices?
<choice ident=A> Encapsulation mode
<choice ident=B> Transform mode
<choice ident=C> Proposal name
<choice ident=D> authentication algorithm
]
item 8.4.1.1
presentation [
2017-1-24
86 , 91
Refer to the graphic. RTA and RTB have established a GRE tunnel, but only RTA has
enabled the keepalive function. When RTB receive a keepalive message from RTA,
how will RTB respond?
<choice ident=A> RTB will discard the keepalive message.
<choice ident=B> RTB willl record receipt of the keepalive message but wont reply
<choice ident=C> RTB will send a keepalive in response.
<choice ident=D> RTB will send a keepalive reply and begin to actively send
keepalive messages.
]
item 8.4.2.1
presentation [
Refer to the graphic. Two hosts communicate through a GRE tunnel. When the GRE
tunnel is up, the network administrator configures a static route on RTA to route
packets to Host B. Which of the following commands will achieve this?
<choice ident=A> ip route-static 10.1.2.0 24 GigabitEthernet0/0/1
<choice ident=B> ip route-static 10.1.2.0 24 200.2.2.1
<choice ident=C> ip route-static 10.1.2.0 24 200.1.1.1
<choice ident=D> ip route-static 10.1.2.0 24 tunnel 0/0/1
]
item 9.1.1.1
presentation [
which version of SNMP supports data encryption?
<choice ident=A> SNMPv1
<choice ident=B> SNMPv2
<choice ident=C> SNMPv2c
<choice ident=D> SNMPv3
]
item 9.1.1.2
presentation [
Which of the following statements regarding traps in SNMP is correct?
<choice ident=A> Traps are transmitted using UDP to destination port number 162.
<choice ident=B> Traps are transmitted using UDP to destination port number 161.
<choice ident=C> Traps are transmitted using TCP to destination port number 162.
<choice ident=D> Traps are transmitted using TCP to destination port number 161.
]
item 9.1.1.3
presentation [
The Network Management Station uses SNMP to manage devices, which SNMP
2017-1-24
87 , 91
message is sent when an SNMP registered abnormal event occurs?

<choice ident=A> get-response
<choice ident=B> set-request
<choice ident=C> trap
<choice ident=D> get-request
]
item 9.2.1.1
presentation [
Which of the following descriptions regarding eSight is not correct?
<choice ident=A> eSight is used to monitor and manage enterprise networks.
<choice ident=B> eSight supports only Huawei devices
<choice ident=C> eSight supports WLAN management and monitoring of hotspot
coverage.
<choice ident=D> eSight supports the backup of configuration files and network
traffic analysis.
]
item 9.2.1.2
correct-response = "A,C,D
minnumber = 3
maxnumber =3
presentation [
eSight supports which of the following SNMP versions in order to manage devices?
(Three Answers).
<choice ident=A> SNPMv1
<choice ident=B> SNPMv2
<choice ident=C> SNPMv2c
<choice ident=D> SNPMv3
]
item 10.1.1.1
minnumber = 2
maxnumber =2
presentation [
Which of the following formats represent an accurate condensing of the IPv6 address
2031:0000:720C:0000:0000:09E0:839A:130B? (Two Answers).
<choice ident=A> 2031:0:720C:0:0:9E0:839A:130B
<choice ident=B> 2031:0:720C:0:0:9E:839A:130B
<choice ident=C> 2031::720C::9E0:839A:130B
<choice ident=D> 2031:0:720C::9E0:839A:130B
]
item 10.1.1.2
minnumber = 2
2017-1-24
88 , 91
maxnumber =2
presentation [
Which of the following IPv6 addresses can be configured on a routers interface?
(Two Answers).
<choice ident=A> fe80:13dc::1/64
<choice ident=B> ff00:8a3c::9b/64
<choice ident=C> ::1/128
<choice ident=D> 2001:12e3:1b02::21/64
]
item 10.1.1.3
presentation [
The IPv6 address achitecture does not include which of the following address types?
]
item 10.1.2.1
minnumber = 2
maxnumber =2
presentation [
Which of the following descriptions regarding IPv6 addresses are correct? (Two
Answers)
<choice ident=A> IPv6 addresses are 64 bits in length.
<choice ident=B> IPv6 addresses are 128 bits in length.
<choice ident=C> IPv6 extension headers are processed in order.
<choice ident=D> IPv6 extension headers are processed randomly.
]
item 10.1.2.2
presentation [
Interface G0/0/1 on RTA contains a MAC address of 00e0-fc03-aa73 and is
configured with the IPv6 address 2001::2E0:FCFF:FE03:AA73. Which method is
most likely to have been used to configure the interface IPv6 address?
<choice ident=A> DHCPv6
<choice ident=B> Auto-link
<choice ident=C> ARP
<choice ident=D> EUI-64
]
item 10.2.1.1
2017-1-24
89 , 91
presentation [
In a small network suppporting IPv6, a network administrator wishes implement
RIPng. Which of the following commands should be used to enable this protocol?
<choice ident=A> [RTA-GigabitEthernet0/0/0]ripng 1 enable
<choice ident=B> [RTA]ripng 1 enable
<choice ident=C> <RTA>ripng 1 enable
<choice ident=D> [RTA-ripng-1]ripng 1 enable
]
item 10.2.1.2
presentation [
In a network supporting IPv6, OSPF no longer supports which feature?
<choice ident=A> multiple areas
<choice ident=B> Router-ID
<choice ident=C> authentication
<choice ident=D> multicast updates
]
item 10.2.1.3
presentation [
Two routers are configured with OSPFv3. OSPFv3 is enabled on all interfaces of
each router. Which of the following is true in the event that the network administrator
does not configure a Router-ID?
<choice ident=A> The IP address of the loopback 0 interface will be used as the
router ID
<choice ident=B> The IP address of the loopback 1 interface will be used as the
router ID
<choice ident=C> The IP address of interface G0/0/0 will be used as the router ID
<choice ident=D> No router ID will be assigned to the router.
]
item 10.2.1.5
minnumber = 2
maxnumber =2
presentation [
Refer to the graphic. RTA and RTB have established an IPv6 network for which an
IPv6 address has been configured only on the G0/0/1 interface. RTA is unable to ping
RTB. The administrator then configures OSPFv3 along with a router-id on both
routers, and enables OSPFv3 on G0/0/1 of both RTA and RTB. Which of the
following statements are correct? (Two Answers).
<choice ident=A> RTA and RTB can establish an OSPFv3 neighbor relationship.
<choice ident=B> RTA and RTB cannot establish an OSPFv3 neighbor relationship.
<choice ident=C> RTA can ping RTB.
<choice ident=D> RTA cannot ping RTB.
2017-1-24
90 , 91
item 10.3.1.4
correct-response = "A,B
minnumber = 2
maxnumber =2
presentation [
A DHCP Unique Identifier (DUID) in DHCPv6 can be configured in VRP using which
formats? (Two Answers).
<choice ident=A> DUID-LL
<choice ident=B> DUID-LLT
<choice ident=C> DUID-EN
<choice ident=D> DUID-LLC
]
2017-1-24
91 , 91

HCDA (Dumps)

Uploaded by

Copyright:

Available Formats

HCDA (Dumps)

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

HCDA (Dumps)

Uploaded by

Copyright:

Available Formats

item 1.1.1.

10.0.12.1 10.0.12.2 TCP

connectivity problems between the host and the local gateway.

<choice ident=C> Hosts will be unable to comminicate unless arp-proxy is enabled

items will change

<choice ident="A">Through the Console port

Refer to the display output. Which statement is false?

5489-98ec-f01. What operation will occur on the switch?

<choice ident=A> Port G0/0/1 of switch A

ip route-static 10.0.12.0 255.255.255.0 192.168.1.1

<choice ident=C>The route 10.0.2.0

<choice ident="A">Configuration of a router ID

what will behavior will occur as a result of the configuration?

<choice ident=B> DHCP REQUEST

<choice ident=A>The interfaces will be aggregated with load balancing.

<choice ident=B> G0/0/2 on SWB is associated with VLAN 10.

Refer to the graphic.Host A and Host B uses VLAN routing to facilitate

layer encapsulation type of a serial interface as HDLC?

<choice ident="A">ppp pap

<choice ident=A> [RTA-Serial1/0/1]fr map ip 172.16.1.1 30

for Frame Relay network? (Select 2 Answers)

<choice ident=B> The destination MAC address is used.

[RTA-Gigabitethernet0/0/1]nat server protocol tcp global 202.10.10.1 www inside

<choice ident=A> A basic ACL value ranges from 1000-2999

<choice ident=C> The rule-number of the second rule is 2

<choice ident=B>The administrator should configure AAA to manage user

message is sent when an SNMP registered abnormal event occurs?

You might also like