Basic Electrical Notes

You can get more notes here: http://vtunotes.kwatle.
com
SINGLE PHASE AC CIRCUITS

Definition of Alternating Quantity
e
+Em
/2
3/2 2 t
-Em
T
An alternating quantity changes continuously in magnitude and alternates in direction at regular
intervals of time. Important terms associated with an alternating quantity are defined below.
1. Amplitude
It is the maximum value attained by an alternating quantity. Also called as maximum or peak
value
2. Time Period (T)

It is the Time Taken in seconds to complete one cycle of an alternating quantity
3. Instantaneous Value
It is the value of the quantity at any instant
4. Frequency (f)
It is the number of cycles that occur in one second. The unit for frequency is Hz or cycles/sec.
The relationship between frequency and time period can be derived as follows.
Time taken to complete f cycles = 1 second
Time taken to complete 1 cycle = 1/f second
T = 1/f
You can get more notes here: http://vtunotes.kwatle.com
Advantages of AC system over DC system

1. AC voltages can be efficiently stepped up/down using transformer
2. AC motors are cheaper and simpler in construction than DC motors
3. Switchgear for AC system is simpler than DC system
Generation of sinusoidal AC voltage

Consider a rectangular coil of N turns placed in a uniform magnetic field as shown in the figure. The
coil is rotating in the anticlockwise direction at an uniform angular velocity of rad/sec.
When the coil is in the vertical position, the flux linking the coil is zero because the plane of the coil
is parallel to the direction of the magnetic field. Hence at this position, the emf induced in the coil is
zero. When the coil moves by some angle in the anticlockwise direction, there is a rate of change of
flux linking the coil and hence an emf is induced in the coil. When the coil reaches the horizontal
position, the flux linking the coil is maximum, and hence the emf induced is also maximum. When
the coil further moves in the anticlockwise direction, the emf induced in the coil reduces. Next when
the coil comes to the vertical position, the emf induced becomes zero. After that the same cycle
repeats and the emf is induced in the opposite direction. When the coil completes one complete
revolution, one cycle of AC voltage is generated.
The generation of sinusoidal AC voltage can also be explained using mathematical equations.
Consider a rectangular coil of N turns placed in a uniform magnetic field in the position shown in the
figure. The maximum flux linking the coil is in the downward direction as shown in the figure. This
flux can be divided into two components, one component acting along the plane of the coil maxsint
and another component acting perpendicular to the plane of the coil maxcost.
rad/sec
x
maxsint
max
maxcost
The component of flux acting along the plane of the coil does not induce any flux in the coil. Only
the component acting perpendicular to the plane of the coil ie maxcost induces an emf in the coil.
= max cos t
d
dt
d
e = N max cos t
dt
e = N max sin t
e = N
e = E m sin t
Hence the emf induced in the coil is a sinusoidal emf. This will induce a sinusoidal current in the
circuit given by
i = I m sin t
Angular Frequency ()
Angular frequency is defined as the number of radians covered in one second(ie the angle covered by
the rotating coil). The unit of angular frequency is rad/sec.
2
= 2f
T
Problem 1
An alternating current i is given by
i = 141.4 sin 314t
Find i) The maximum value
ii) Frequency
iii) Time Period
iv) The instantaneous value when t=3ms
i = 141.4 sin 314t
i = I m sin t
i) Maximum value Im=141.4 V
ii) = 314 rad/sec
f = /2 = 50 Hz
iii) T=1/f = 0.02 sec
iv) i=141.4 sin(314x0.003) = 114.35A
Average Value
The arithmetic average of all the values of an alternating quantity over one cycle is called its average
value
Average value = Area under one cycle
Base
1
Vav =
2
vd (t )
0
For Symmetrical waveforms, the average value calculated over one cycle becomes equal to zero
because the positive area cancels the negative area. Hence for symmetrical waveforms, the average
value is calculated for half cycle.
Average value = Area under one half cycle
Base
Vav =
vd (t )
0
Average value of a sinusoidal current
i = I m sin t
i
+Im
I av =
id (t )
2 t
I av =
I av =
-Im
Average value of a full wave rectifier output

i
+Im
sin td (t )
2I m
= 0.637 I m
i = I m sin t
I av =
id (t )
I av =
-Im
I av =
sin td (t )
2I m
= 0.637 I m
Average value of a half wave rectifier output
i = I m sin t
1
I av =
2
i
+Im
id (t )
0
1
I av =
I m sin td (t )
2 0
-Im
I av =
Im
= 0.318I m
RMS or Effective Value

The effective or RMS value of an alternating quantity is that steady current (dc) which when flowing
through a given resistance for a given time produces the same amount of heat produced by the
alternating current flowing through the same resistance for the same time.
Idc
Iac
Area under squared

curve e
Areaunders
quaredcurv
base
RMS =
Vrms
1
=
2
2
v
d (t )
0
RMS value of a sinusoidal current
i = I m sin t
i
+Im
I rms
2 t
-Im
i
+Im
I rms =
I rms =
RMS value of a full wave rectifier output
i d (t )
2
2
2
td (t )
I
sin
m
Im
= 0.707 I m
2
i = I m sin t
I rms
1
=
2
1
=
2
I rms =
i d (t )
2
2
m
sin 2 td (t )
-Im
I rms =
RMS value of a half wave rectifier output

i
+Im
Im
= 0.707 I m
2
i = I m sin t
I rms
1
=
2
2
i
d (t )
0
-Im
I rms
1
I m2 sin 2 td (t )
=
2 0
I rms =
Im
= 0.5 I m
2
Form Factor
The ratio of RMS value to the average value of an alternating quantity is known as Form Factor
FF =
RMSValue
AverageValue
Peak Factor or Crest Factor

The ratio of maximum value to the RMS value of an alternating quantity is known as the peak factor
PF =
MaximumValue
RMSValue
For a sinusoidal waveform
I av =
2I m
= 0.637 I m
Im
= 0.707 I m
2
I
0.707 I m
FF = rms =
= 1.11
I av 0.637 I m
I rms =
PF =
Im
Im
=
= 1.414
I rms 0.707 I m
For a Full Wave Rectifier Output
I av =
2I m
= 0.637 I m
Im
= 0.707 I m
2
I
0.707 I m
FF = rms =
= 1.11
I av 0.637 I m
I rms =
PF =
Im
Im
=
= 1.414
I rms 0.707 I m
For a Half Wave Rectifier Output
I av =
Im
= 0.318 I m
Im
= 0.5 I m
2
I
0.5 I m
FF = rms =
= 1.57
I av 0.318 I m
I rms =
PF =
Im
I
= m =2
I rms 0.5 I m
Phasor Representation
An alternating quantity can be represented using
(i)
Waveform
(ii)
Equations
(iii)
Phasor
A sinusoidal alternating quantity can be represented by a rotating line called a Phasor. A phasor is a
line of definite length rotating in anticlockwise direction at a constant angular velocity
The waveform and equation representation of an alternating current is as shown. This sinusoidal
quantity can also be represented using phasors.
i
+Im
-Im
i = I m sin t
2 t
Draw a line OP of length equal to Im. This line OP rotates in the anticlockwise direction with a
uniform angular velocity rad/sec and follows the circular trajectory shown in figure. At any
instant, the projection of OP on the y-axis is given by OM=OPsin = Imsint. Hence the line OP is
the phasor representation of the sinusoidal current
Phase
Phase is defined as the fractional part of time period or cycle through which the quantity has
advanced from the selected zero position of reference
Phase of +Em is /2 rad or T/4 sec
Phase of -Em is 3/2 rad or 3T/4 sec
Phase Difference
When two alternating quantities of the same frequency have different zero points, they are said to
have a phase difference. The angle between the zero points is the angle of phase difference.
In Phase
Two waveforms are said to be in phase, when the phase difference between them is zero. That is the
zero points of both the waveforms are same. The waveform, phasor and equation representation of
two sinusoidal quantities which are in phase is as shown. The figure shows that the voltage and
current are in phase.
Lagging
In the figure shown, the zero point of the current waveform is after the zero point of the voltage
waveform. Hence the current is lagging behind the voltage. The waveform, phasor and equation
representation is as shown.
Leading
In the figure shown, the zero point of the current waveform is before the zero point of the voltage
waveform. Hence the current is leading the voltage. The waveform, phasor and equation
representation is as shown.
AC circuit with a pure resistance
Consider an AC circuit with a pure resistance R as shown in the figure. The alternating voltage v is
given by
v = Vm sin t
---------- (1)
The current flowing in the circuit is i. The voltage across the resistor is given as VR which is the
same as v.
Using ohms law, we can write the following relations
v Vm sin t
=
R
R
---------------(2)
i = I m sin t
i=
Where
Im =
Vm
R
From equation (1) and (2) we conclude that in a pure resistive circuit, the voltage and current are in
phase. Hence the voltage and current waveforms and phasors can be drawn as below.
Instantaneous power
The instantaneous power in the above circuit can be derived as follows
p = vi
p = (Vm sin t )( I m sin t )

p = Vm I m sin 2 t
Vm I m
(1 cos 2t )
2
V I
V I
p = m m m m cos 2t
2
2
p=
The instantaneous power consists of two terms. The first term is called as the constant power term
and the second term is called as the fluctuating power term.
Average power
From the instantaneous power we can find the average power over one cycle as follows
1
P=
2
Vm I m Vm I m
cos
2
t
0 2
dt
2
Vm I m
0 2 cos 2t dt
V I
V I
P= m m = m m
2
2 2
P = V .I
V I
1
P= m m
2
2
As seen above the average power is the product of the rms voltage and the rms current.
The voltage, current and power waveforms of a purely resistive circuit is as shown in the figure.
As seen from the waveform, the instantaneous power is always positive meaning that the power
always flows from the source to the load.
Phasor Algebra for a pure resistive circuit

V = V0o = V + j 0
I=
V V + j0
=
= I + j 0 = I0o
R
R
Problem 2
An ac circuit consists of a pure resistance of 10 and is connected to an ac supply of 230 V, 50 Hz.
Calculate the (i) current (ii) power consumed and (iii) equations for voltage and current.
V 230
(i) I = =
= 23 A
R 10
(ii ) P = VI = 230 23 = 5260W
(iii )Vm = 2V = 325.27V
I m = 2 I = 32.52 A
= 2f = 314rad / sec
v = 325.25 sin 314t
i = 32.52 sin 314t
AC circuit with a pure inductance
Consider an AC circuit with a pure inductance L as shown in the figure. The alternating voltage v is
given by
v = Vm sin t
---------- (1)
The current flowing in the circuit is i. The voltage across the inductor is given as VL which is the
same as v.
We can find the current through the inductor as follows
v=L
di
dt
Vm sin t = L
di
dt
Vm
sin tdt
L
V
i = m sin tdt
L
V
i = m ( cos t )
L
V
i = m sin(t / 2)
L
i = I m sin(t / 2)
di =
Where
Im =
Vm
L
-------------------(2)
From equation (1) and (2) we observe that in a pure inductive circuit, the current lags behind the
voltage by 90. Hence the voltage and current waveforms and phasors can be drawn as below.
Inductive reactance
The inductive reactance XL is given as
X L = L = 2fL
Im =
Vm
XL
It is equivalent to resistance in a resistive circuit. The unit is ohms ()
Instantaneous power
p = vi
p = (Vm sin t )( I m sin(t / 2))

p = Vm I m sin t cos t
Vm I m
p=
sin 2t
2
As seen from the above equation, the instantaneous power is fluctuating in nature.
Average power
1
P=
2
Vm I m
sin 2tdt
2
P=0
The average power in a pure inductive circuit is zero. Or in other words, the power consumed by a
pure inductance is zero.
The voltage, current and power waveforms of a purely inductive circuit is as shown in the figure.
As seen from the power waveform, the instantaneous power is alternately positive and negative.
When the power is positive, the power flows from the source to the inductor and when the power in
negative, the power flows from the inductor to the source. The positive power is equal to the
negative power and hence the average power in the circuit is equal to zero. The power just flows
between the source and the inductor, but the inductor does not consume any power.
Phasor algebra for a pure inductive circuit
V = V0o = V + j 0
I = I 90o = 0 jI
V
V0o
=
= X L 90o
I I 90
V = I ( jX L )
Problem 3
A pure inductive coil allows a current of 10A to flow from a 230V, 50 Hz supply. Find (i) inductance
of the coil (ii) power absorbed and (iii) equations for voltage and current.
V 230
=
= 23
I
10
X L = 2fL
(i ) X L =
XL
= 0.073H
2f
(ii ) P = 0
L=
(iii )Vm = 2V = 325.27V

I m = 2 I = 14.14 A
= 2f = 314rad / sec
v = 325.25 sin 314t
i = 14.14 sin(314t / 2)
AC circuit with a pure capacitance
Consider an AC circuit with a pure capacitance C as shown in the figure. The alternating voltage v is
given by
v = Vm sin t
---------- (1)
The current flowing in the circuit is i. The voltage across the capacitor is given as VC which is the
same as v.
We can find the current through the capacitor as follows
q = Cv
q = CVm sin t
dq
dt
i = CVm cos t
i=
i = CVm sin(t + / 2)
i = I m sin(t + / 2)
Where
-------------------(2)
I m = CVm
From equation (1) and (2) we observe that in a pure capacitive circuit, the current leads the voltage
by 90. Hence the voltage and current waveforms and phasors can be drawn as below.
Capacitive reactance
The capacitive reactance XC is given as
1
1
=
C 2fC
V
Im = m
XC
XL =
It is equivalent to resistance in a resistive circuit. The unit is ohms ()
Instantaneous power
p = vi
p = (Vm sin t )( I m sin(t + / 2))
p = Vm I m sin t cos t
p=
Vm I m
sin 2t
2
As seen from the above equation, the instantaneous power is fluctuating in nature.
Average power
1
P=
2
Vm I m
0 2 sin 2tdt
P=0
The average power in a pure capacitive circuit is zero. Or in other words, the power consumed by a
pure capacitance is zero.
The voltage, current and power waveforms of a purely capacitive circuit is as shown in the figure.
When the power is positive, the power flows from the source to the capacitor and when the power in
negative, the power flows from the capacitor to the source. The positive power is equal to the
negative power and hence the average power in the circuit is equal to zero. The power just flows
between the source and the capacitor, but the capacitor does not consume any power.
Phasor algebra in a pure capacitive circuit
V = V0o = V + j 0
I = I90o = 0 + jI
V V0o
=
= X C 90o
I I90
V = I ( jX C )
Problem 4
A 318F capacitor is connected across a 230V, 50 Hz system. Find (i) the capacitive reactance (ii)
rms value of current and (iii) equations for voltage and current.
1
= 10
2fC
V
(ii ) I =
= 23 A
XC
(i ) X C =
(iii )Vm = 2V = 325.27V

I m = 2 I = 32.53 A
= 2f = 314rad / sec
v = 325.25 sin 314t
i = 32.53 sin(314t + / 2)
R-L Series circuit
Consider an AC circuit with a resistance R and an inductance L connected in series as shown in the
figure. The alternating voltage v is given by
v = Vm sin t
The current flowing in the circuit is i. The voltage across the resistor is VR and that across the
inductor is VL.
VR=IR is in phase with I
VL=IXL leads current by 90 degrees
With the above information, the phasor diagram can be drawn as shown.
The current I is taken as the reference phasor. The voltage VR is in phase with I and the voltage VL
leads the current by 90. The resultant voltage V can be drawn as shown in the figure. From the
phasor diagram we observe that the voltage leads the current by an angle or in other words the
current lags behind the voltage by an angle .
The waveform and equations for an RL series circuit can be drawn as below.
V = Vm sin t
I = I m sin(t )
From the phasor diagram, the expressions for the resultant voltage V and the angle can be derived
as follows.
V = VR2 + VL2
VR = IR
VL = IX L
V = ( IR) 2 + ( IX L ) 2
V = I R 2 + X L2
V = IZ
Where impedance Z = R 2 + X 2
L
The impedance in an AC circuit is similar to a resistance in a DC circuit. The unit for impedance is
ohms ().
Phase angle
V
= tan 1 L
VR
IX
= tan 1 L
IR
X
= tan 1 L
R
L
= tan 1
Instantaneous power
The instantaneous power in an RL series circuit can be derived as follows
p = vi
p = (Vm sin t )( I m sin(t )

p=
Vm I m
V I
cos m m cos(2t )
2
2
The instantaneous power consists of two terms. The first term is called as the constant power term
and the second term is called as the fluctuating power term.
Average power
1
P=
2
Vm I m
Vm I m
cos
cos(
2
t
)
0 2
d t
2
Vm I m
cos
2
V I
P = m m cos
2 2
P = VI cos
P=
The voltage, current and power waveforms of a RL series circuit is as shown in the figure.
When the power is positive, the power flows from the source to the load and when the power in
negative, the power flows from the load to the source. The positive power is not equal to the negative
power and hence the average power in the circuit is not equal to zero.
From the phasor diagram,
VR IR R
=
=
V
IZ Z
P = VI cos
R
P = ( IZ ) I
Z
2
P=I R
cos =
Hence the power in an RL series circuit is consumed only in the resistance. The inductance does not
consume any power.
Power Factor
The power factor in an AC circuit is defined as the cosine of the angle between voltage and current ie
cos
P = VI cos
The power in an AC circuit is equal to the product of voltage, current and power factor.
Impedance Triangle
We can derive a triangle called the impedance triangle from the phasor diagram of an RL series
circuit as shown
The impedance triangle is right angled triangle with R and XL as two sides and impedance as the
hypotenuse. The angle between the base and hypotenuse is . The impedance triangle enables us to
calculate the following things.
1. Impedance
Z = R 2 + X L2
2. Power Factor cos =

3. Phase angle
R
Z
X
= tan 1 L
R
4. Whether current leads or lags behind the voltage
Power
In an AC circuit, the various powers can be classified as
1. Real or Active power
2. Reactive power
3. Apparent power
Real or active power in an AC circuit is the power that does useful work in the cicuit. Reactive
power flows in an AC circuit but does not do any useful work. Apparent power is the total power in
an AC circuit.
From the phasor diagram of an RL series circuit, the current can be divided into two components.
One component along the voltage Icos, that is called as the active component of current and
another component perpendicular to the voltage Isin that is called as the reactive component of
current.
Real Power
The power due to the active component of current is called as the active power or real power. It is
denoted by P.
P = V x ICos = I2R
Real power is the power that does useful power. It is the power that is consumed by the resistance.
The unit for real power in Watt(W).
Reactive Power
The power due to the reactive component of current is called as the reactive power. It is denoted by
Q.
Q = V x ISin = I2XL
Reactive power does not do any useful work. It is the circulating power in th L and C components.
The unit for reactive power is Volt Amperes Reactive (VAR).
Apparent Power
The apparent power is the total power in the circuit. It is denoted by S.
S = V x I = I2Z
S = P2 + Q2
The unit for apparent power is Volt Amperes (VA).
Power Triangle
From the impedance triangle, another triangle called the power triangle can be derived as shown.
The power triangle is right angled triangle with P and Q as two sides and S as the hypotenuse. The
angle between the base and hypotenuse is . The power triangle enables us to calculate the following
things.
1. Apparent power
2. Power Factor
S = P2 + Q2
Cos =
P
Re alPower
=
S ApparentPower
The power Factor in an AC circuit can be calculated by any one of the following
methods
Cosine of angle between V and I
Resistance/Impedance R/Z
Real Power/Apparent Power P/S
Phasor algebra in a RL series circuit
V = V + j 0 = V0o
Z = R + jX L = Z
V V
I = =
Z Z
S = VI * = P + jQ
Problem 5
A coil having a resistance of 7 and an inductance of 31.8mH is connected to 230V, 50Hz supply.
Calculate (i) the circuit current (ii) phase angle (iii) power factor (iv) power consumed
X L = 2fL = 2 3.14 50 31.8 10 3 = 10

Z = R 2 + X L2 = 7 2 + 10 2 = 12.2
V 230
=
= 18.85 A
Z 12.2
X
10
(ii ) = tan 1 L = tan 1 = 55o lag
R
7
(iii ) PF = cos = cos(55o ) = 0.573lag
(iv ) P = VI cos = 230 18.85 0.573 = 2484.24W
(i ) I =
Problem 6
A 200 V, 50 Hz, inductive circuit takes a current of 10A, lagging 30 degree. Find (i) the resistance
(ii) reactance (iii) inductance of the coil
V 200
=
= 20
I
10
(i ) R = Z cos = 20 cos 30o = 17.32
Z=
(ii ) X L = Z sin = 20 sin 30o = 10

(iii ) L =
XL
10
=
= 0.0318H
2f 2 3.14 50
R-C Series circuit
Consider an AC circuit with a resistance R and a capacitance C connected in series as shown in the
figure. The alternating voltage v is given by
v = Vm sin t
The current flowing in the circuit is i. The voltage across the resistor is VR and that across the
capacitor is VC.
VC=IXC lags behind the current by 90 degrees
With the above information, the phasor diagram can be drawn as shown.
The current I is taken as the reference phasor. The voltage VR is in phase with I and the voltage VC
lags behind the current by 90. The resultant voltage V can be drawn as shown in the figure. From
the phasor diagram we observe that the voltage lags behind the current by an angle or in other
words the current leads the voltage by an angle .
The waveform and equations for an RC series circuit can be drawn as below.
V = Vm sin t
I = I m sin(t + )
as follows.
V = VR2 + VC2
VR = IR
VC = IX C
V = ( IR) 2 + ( IX C ) 2
V = I R 2 + X C2
V = IZ
Where impedance
Z = R 2 + X C2
Phase angle
V
= tan 1 C
VR
IX
= tan 1 C
IR
X
= tan 1 C
R
1
= tan 1
CR
Average power
P = VI cos
P = ( IZ ) I
R
Z
P = I 2R
Hence the power in an RC series circuit is consumed only in the resistance. The capacitance does not
consume any power.
Impedance Triangle
We can derive a triangle called the impedance triangle from the phasor diagram of an RC series
circuit as shown
Phasor algebra for RC series circuit
V = V + j 0 = V0o
Z = R jX C = Z
I=
V V
= +
Z Z
Problem 7
A Capacitor of capacitance 79.5F is connected in series with a non inductive resistance of 30
across a 100V, 50Hz supply. Find (i) impedance (ii) current (iii) phase angle (iv) Equation for the
instantaneous value of current
XC =
1
1
=
= 40
2fC 2 3.14 50 79.5 10 6
(i ) Z = R 2 + X C2 = 30 2 + 40 2 = 50
V 100
=
= 2A
Z 50
X
40
(iii ) = tan 1 C = tan 1 = 53o lead
R
30
(ii ) I =
(iv) I m = 2 I = 2 2 = 2.828 A
= 2f = 2 3.14 50 = 314rad / sec

i = 2.828 sin(314t + 53o )
R-L-C Series circuit
Consider an AC circuit with a resistance R, an inductance L and a capacitance C connected in series

as shown in the figure. The alternating voltage v is given by
v = Vm sin t
The current flowing in the circuit is i. The voltage across the resistor is VR, the voltage across the
inductor is VL and that across the capacitor is VC.
VL=IXL leads the current by 90 degrees
VC=IXC lags behind the current by 90 degrees
With the above information, the phasor diagram can be drawn as shown. The current I is taken as the
reference phasor. The voltage VR is in phase with I, the voltage VL leads the current by 90 and the
voltage VC lags behind the current by 90. There are two cases that can occur VL>VC and VL<VC
depending on the values of XL and XC. And hence there are two possible phasor diagrams. The
phasor VL-VC or VC-VL is drawn and then the resultant voltage V is drawn.
VL>VC
VL<VC
From the phasor diagram we observe that when VL>VC , the voltage leads the current by an angle
or in other words the current lags behind the voltage by an angle . When VL<VC ,the voltage
lags behind the current by an angle or in other words the current leads the voltage by an angle
.
as follows.
V = VR2 + (VL VC ) 2
V = ( IR) 2 + ( IX L IX C ) 2
V = I R 2 + ( X L X C )2
V = IZ
Where impedance
Z = R 2 + ( X L X C )2
Phase angle
V V
= tan 1 L C
VR
IX IX C
= tan 1 L
IR
X XC
= tan 1 L
From the expression for phase angle, we can derive the following three cases
Case (i): When XL>XC
The phase angle is positive and the circuit is inductive. The circuit behaves like a series RL circuit.
Case (ii): When XL<XC
The phase angle is negative and the circuit is capacitive. The circuit behaves like a series RC
circuit.
Case (iii): When XL=XC
The phase angle = 0 and the circuit is purely resistive. The circuit behaves like a pure resistive
circuit.
The voltage and the current can be represented by the following equations. The angle is positive or
negative depending on the circuit elements.
V = Vm sin t
I = I m sin(t )
Average power
P = VI cos
P = ( IZ ) I
R
Z
P = I 2R
Hence the power in an RLC series circuit is consumed only in the resistance. The inductance and the
capacitance do not consume any power.
Phasor algebra for RLC series circuit
V = V + j 0 = V0o
Z = R + j ( X L X C ) = Z
I=
V V
=
Z Z
Problem 8
A 230 V, 50 Hz ac supply is applied to a coil of 0.06 H inductance and 2.5 resistance connected in
series with a 6.8 F capacitor. Calculate (i) Impedance (ii) Current (iii) Phase angle between current
and voltage (iv) power factor (v) power consumed
X L = 2 fL = 2 3 .14 50 0 . 06 = 18 .84
XC =
1
1
=
= 468
2 fC
2 3 . 14 50 6 . 8 10 6
(i ) Z =
R 2 + (X L X C ) =
2
2 . 5 2 + (18 . 84 468 ) = 449 . 2
V
230
=
= 0 . 512 A
Z
449 .2
X XC
1 18 . 84 468
o
( iii ) = tan 1 L
= tan
= 89 . 7
R
30
( iv ) pf = cos = cos 89 . 7 = 0 . 0056 lead

( ii ) I =
( v ) P = VI cos = 230 0 . 512 0 .0056 = 0 . 66W
Problem 9
A resistance R, an inductance L=0.01 H and a capacitance C are connected in series. When an
alternating voltage v=400sin(3000t-20)is applied to the series combination, the current flowing is
10 2 sin(3000t-65). Find the values of R and C.
= 65o 20 o = 45o lag

X L = L = 3000 0.01 = 30
tan = tan 45o = 1
X L XC
=1
R
R = X L XC
tan =
Z=
Vm
400
2
=
= 28.3Z = R 2 + ( X L X C ) = R 2 + R 2
I m 10 2
2 R = 28.3
R = 20
X L X C = 20
X C = 30 20 = 10
C=
1
1
=
= 33.3F
X C 3000 10
Problem 10
A coil of pf 0.6 is in series with a 100F capacitor. When connected to a 50Hz supply, the potential
difference across the coil is equal to the potential difference across the capacitor. Find the resistance
and inductance of the coil.
coscoil= 0.6
C=100F
f = 50Hz
Vcoil=Vc
1
1
=
= 31.83
2fC 2 3.14 50 100 10 6
= Vc
XC =
Vcoil
IZ coil = IX C
Z coil = X C = 31.83
R = Z coil cos coil = 31.83 0.6 = 19.09
2
X L = Z coil
R 2 = 31.832 19.09 2 = 25.46
L=
1
1
=
= 0.081H
2fL 2 3.14 50 25.46
Problem 11
A current of (120-j50)A flows through a circuit when the applied voltage is (8+j12)V. Determine (i)
impedance (ii) power factor (iii) power consumed and reactive power
V = 8 + j12
I = 120 j 50
V
8 + j12
=
= 0.02 + j 0.11 = 0.1179.7 o
120
j
50
I
Z = 0.11
(i ) Z =
= 79.7 o
(ii ) pf = cos = cos 79.7 o = 0.179lag
(iii ) S = VI * = (8 + j12 ) (120 + j 50 ) = 360 + j1840
S = P + jQ
P = 360W
Q = 1840VAR
Problem 12
The complex Volt Amperes in a series circuit are (4330-j2500) and the current is (25+j43.3)A.
Find the applied voltage.
S = 4330 + j 2500
I = 25 + j 43.3
V=
S
I*
4330 + j 2500
= 86.6 + j 50
25 j 43.3
Problem 13
A parallel circuit comprises of a resistor of 20 in series with an inductive reactance 15 in one
branch and a resistor of 30 in series with a capacitive reactance of 20 in the other branch.
Determine the current and power dissipated in each branch if the total current drawn by the parallel
circuit is 10-30 A
Z 1 = 20 + j15
Z 2 = 30 j 20
I = 10 30 o = 8.66 j 5
I1 = I
Z2
(30 j 20)
= (8.66 j 5)
(20 + j15) + (30 j 20)
Z1 + Z 2
I 1 = 3.8 j 6.08 = 7.17 60 o

I 2 = I I 1 = (8.66 j 5) (3.8 j 6.08)
I 2 = 4.86 + j1.08 = 4.98 12.5 o
P1 = I 12 R1 = 7.17 2 20 = 1028.2W
P1 = I 22 R 2 = 4.98 2 30 = 744W
Problem 14
A non inductive resistor of 10 is in series with a capacitor of 100F across a 250V, 50Hz ac
supply. Determine the current taken by the capacitor and power factor of the circuit
1
1
=
= 31.83
2fC 2 3.14 50 100 10 6
Z = R jX C = 10 j 31.83
XC =
I=
V
250
=
= 2.24 + j 7.14 = 7.4972.5o
Z 10 j31.83
= 72.5o
pf = cos = cos 72.5o = 0.3
Problem 15
An impedance coil in parallel with a 100F capacitor is connected across a 200V, 50Hz supply. The
coil takes a current of 4A and the power loss in the coil is 600W. Calculate (i) the resistance of the
coil (ii) the inductance of the coil (iii) the power factor of the entire circuit.
V 200
=
= 50
I
4
P = I 2 R = 600W
600 600
R = 2 = 2 = 37.5
I
4
Z coil =
X L = Z coil R 2 = 50 2 37.5 2 = 33.07

XL
33.07
=
= 0.105H
2f 2 3.14 50
1
1
XC =
=
= 31.83
2fC 2 3.14 50 100 10 6
Z1 = R + jX L = 37.5 + j33.07
L=
Z 2 = jX C = j 31.83
Z=
Z1 Z 2
(37.5 + j 33.07 )( j31.83)
=
Z1 + Z 2 (37.5 + j 33.07 ) + ( j 31.83)
Z = 27 j 32.72 = 42.42 50.5o

= 50.5o
pf = cos = cos 50.5o = 0.6365
Problem 16
A series RLC circuit is connected across a 50Hz supply. R=100, L=159.16mH and C=63.7F. If
the voltage across C is 150-90V. Find the supply voltage
X L = 2fL = 2 3.14 50 159.16 10 3 = 50

1
1
=
= 50
2fC 2 3.14 50 63.7 10 6
VC = I ( jX C ) = 150 90o = j150
XC =
I=
j150 j150
=
= 30o A
jX C
j 50
Z = R + j ( X L X C ) = 100 + j (50 50) = 100

V = IZ = 3 100 = 300V
Problem 17
A circuit having a resistance of 20 and inductance of 0.07H is connected in parallel with a series
combination of 50 resistance and 60F capacitance. Calculate the total current, when the parallel
combination is connected across 230V, 50Hz supply.
X L = 2fL = 2 3.14 50 0.07 = 22

1
1
=
= 53
2fC 2 3.14 50 60 10 6
Z1 = 20 + j 22
XC =
Z 2 = 50 j 53
Z=
I=
(20 + j 22)(50 j 53) = 25.7 + j11.9

Z1 Z 2
=
Z1 + Z 2 (20 + j 22) + (50 j 53)
V 230
=
= 7.4 - j3.4 = 8.13 24.9o
Z
Z
THREE PHASE AC CIRCUITS

A three phase supply is a set of three alternating quantities displaced from each other by an angle of
120. A three phase voltage is shown in the figure. It consists of three phases- phase A, phase B and
phase C. Phase A waveform starts at 0. Phase B waveform stars at 120 and phase C waveform at
240.
The three phase voltage can be represented by a set of three equations as shown below.
e A = Em sin t
eB = Em sin(t 120o )
eC = Em sin(t 240o ) = Em sin(t + 120o )
The sum of the three phase voltages at any instant is equal to zero.
e A + eB + eC = 0
The phasor representation of three phase voltages is as shown.
The phase A voltage is taken as the reference and is drawn along the x-axis. The phase B voltage
lags behind the phase A voltage by 120. The phase C voltage lags behind the phase A voltage by
240 and phase B voltage by 120.
Generation of Three Phase Voltage
Three Phase voltage can be generated by placing three rectangular coils displaced in space by 120 in
a uniform magnetic field. When these coils rotate with a uniform angular velocity of rad/sec, a
sinusoidal emf displaced by 120 is induced in these coils.
Necessity and advantages of three phase systems

3 power has a constant magnitude whereas 1 power pulsates from zero to peak value at
twice the supply frequency
A 3 system can set up a rotating magnetic field in stationary windings. This is not possible
with a 1 supply.
For the same rating 3 machines are smaller, simpler in construction and have better
operating characteristics than 1 machines
To transmit the same amount of power over a fixed distance at a given voltage, the 3 system
requires only 3/4th the weight of copper that is required by the 1 system
The voltage regulation of a 3 transmission line is better than that of 1 line
Phase Sequence
The order in which the voltages in the three phases reach their maximum value
For the waveform shown in figure, phase A reaches the maximum value first, followed by phase B
and then by phase C. hence the phase sequence is A-B-C.
Balanced Supply
A supply is said to be balanced if all three voltages are equal in magnitude and displaced by 120
A three phase supply can be connected in two ways - Either in Delta connection or in Star
connection as shown in the figure.
Delta Connection
Star Connection
Balanced Load
A load is said to be balanced if the impedances in all three phases are equal in magnitude and phase
A three phase load can be connected in two ways - Either in Delta connection or in Star
connection as shown in the figure.
Delta Connection
Star Connection
Balanced Star Connected Load

A balanced star connected load is shown in the figure. A phase voltage is defined as voltage across
any phase of the three phase load. The phase voltages shown in figure are EA, EB and EC. A line
voltage is defined as the voltage between any two lines. The line voltages shown in the figure are
EAB, EBC and ECA. The line currents are IA, IB and IC. For a star connected load, the phase currents are
same as the line currents.
Using Kirchoffs voltage law, the line voltages can be written in terms of the phase voltages as
shown below.
E AB = E A E B
E BC = EB EC
ECA = EC E A
The phasor diagram shows the three phase voltages and the line voltage EAB drawn from EA and EB
phasors. The phasor for current IA is also shown. It is assumed that the load is inductive.
From the phasor diagram we see that the line voltage EAB leads the phase voltage EA by 30. The
magnitude of the two voltages can be related as follows.
E AB = 2 E A cos 30o = 3E A
Hence for a balanced star connected load we can make the following conclusions.
El = 3E ph
I l = I ph
Line voltage leads phase voltage by 30
Three phase Power

In a single phase circuit, the power is given by VIcos. It can also be written as VphIphcos. The
power in a three circuit will be three times the power in a single phase circuit.
P = 3E ph I ph cos
P = 3El I l cos
Balanced Delta Connected Load

A balanced delta connected load is shown in the figure. The phase currents are IAB, IBC and ICA. The
line currents are IA, IB and IC. For a delta connected load, the phase voltages are same as the line
voltages given by EAB, EBC and ECA.
Using Kirchoffs current law, the line currents can be written in terms of the phase currents as shown
below.
I A = I AB I CA
I B = I BC I AB
I C = I CA I BC
The phasor diagram shows the three voltages EAB, EBC and ECA and the three phase currents IAB, IBC
and ICA lagging behind the respective phase voltages by an angle . This is drawn by assuming that
the load is inductive. From the phase currents IAB and ICA, the line current IA is drawn as shown in
the figure.
From the phasor diagram we see that the line current IA lags behind the phase phase current IAB by
30. The magnitude of the two currents can be related as follows.
I A = 2 I AB cos 30o = 3I AB
Hence for a balanced delta connected load we can make the following conclusions.
I l = 3I ph
El = E ph
Line current lags behind phase current by 30
Three phase Power

The three phase power for a delta connected load can be derived in the same way as that for a star
connected load.
P = 3E ph I ph cos
P = 3El I l cos
Measurement of power and power factor by two wattmeter method
The power in a three phase circuit can be measured by connecting two wattmeters in any of the two
phases of the three phase circuit. A wattmeter consists of a current coil and a potential coil as shown
in the figure.
The wattmeter is connected in the circuit in such a way that the current coil is in series and carries
the load current and the potential coil is connected in parallel across the load voltage. The wattmeter
reading will then be equal to the product of the current carried by the current coil, the voltage across
the potential coil and the cosine of the angle between the voltage and current.
The measurement of power is first given for a balanced star connected load and then for a balanced
delta connected load.
(i) Balanced star connected load
The circuit shows a balanced star connected load for which the power is to be measured. Two
wattmeter W1 and W2 are connected in phase A and phase C as shown in the figure.
The current coil of wattmeter W1 carries the current IA and its potential coil is connected across the
voltage EAB. A phasor diagram is drawn to determine the angle between IA and EAB as shown.
From the phasor diagram we determine that the angle between the phasors IA and EAB is (30+).
Hence the wattmeter reading W1 is given by
W1=EABIAcos(30+)
The current coil of wattmeter W2 carries the current IC and its potential coil is connected across the
voltage ECB. From the phasor diagram we determine that the angle between the phasors IC and ECB is
(30-). Hence the wattmeter reading W2 is given by
W2=ECBICcos(30-)
Line voltages EAB=ECB=EL
And line currents IA=IC=IL
Hence
W1 = E L I L cos(30 + )
W2 = E L I L cos(30 )
W1 + W2 = EL I L cos(30 + ) + E L I L cos(30 )
W1 + W2 = EL I L (2 cos 30o cos )
W1 + W2 = 3EL I L cos
From the above equations we observe that the sum of the two wattmeter reading gives the three
phase power.
(ii) Balanced delta connected load

The circuit shows a balanced delta connected load for which the power is to be measured. Two
wattmeter W1 and W2 are connected in phase A and phase C as shown in the figure.
The current coil of wattmeter W1 carries the current IA and its potential coil is connected across the
voltage EAB. A phasor diagram is drawn to determine the angle between IA and EAB as shown.
From the phasor diagram we determine that the angle between the phasors IA and EAB is (30+).
Hence the wattmeter reading W1 is given by
W1=EABIAcos(30+)
The current coil of wattmeter W2 carries the current IC and its potential coil is connected across the
voltage ECB. From the phasor diagram we determine that the angle between the phasors IC and ECB is
(30-). Hence the wattmeter reading W2 is given by
W2=ECBICcos(30-)
Line voltages EAB=ECB=EL
And line currents IA=IC=IL
Hence
W1 = E L I L cos(30 + )
W2 = E L I L cos(30 )
W1 + W2 = EL I L cos(30 + ) + E L I L cos(30 )
W1 + W2 = EL I L (2 cos 30o cos )
From the above equations we observe that the sum of the two wattmeter reading gives the three
phase power.
Determination of Real power, Reactive power and Power factor
W1 = EL I L cos(30 + )
W2 = EL I L cos(30 )
W2 W1 = EL I L sin
W W1
tan = 3 2
W
+
W
2
1
W W1
= tan 1 3 2
W
+
W
2
1
P = W1 + W2
Q = 3 (W2 W1 )
W W1

pf = cos = cos tan 1 3 2
W
+
W
2
The power factor can also be determined from the power triangle
From the power triangle,
P = W1 + W2
Q = 3 (W2 W1 )
S = (W1 + W2 ) 2 + 3(W2 W1 ) 2
pf = cos =
P
=
S
W1 + W2
(W1 + W2 ) 2 + 3(W2 W1 ) 2
Wattmeter readings at different Power Factors

(i )upf
= 0o
3
EL I L
2
3
W2 = EL I L cos(30 ) = EL I L cos(30) =
EL I L
2
W1 = W2
W1 = EL I L cos(30 + ) = EL I L cos(30) =
(ii ) pf = 0.866
= 30o
EL I L
2
W2 = E L I L cos(30 ) = E L I L cos(30 30) = EL I L
W1 = E L I L cos(30 + ) = E L I L cos(30 + 30) =

W2 = 2W1
(iii ) pf = 0.5
= 60o
W1 = E L I L cos(30 + ) = E L I L cos(30 + 60) = 0
W2 = E L I L cos(30 ) = E L I L cos(30 60) =
3
EL I L
2
(iv ) pf < 0.5

> 60o
W1 = EL I L cos(30 + ) < 0
W2 = EL I L cos(30 ) > 0
(v) pf = 0
= 90o
EL I L
2
E I
W2 = EL I L cos(30 ) = E L I L cos(30 90) = L L
2
W1 = W2
W1 = E L I L cos(30 + ) = E L I L cos(30 + 90) =
Problem 1
A balanced 3 delta connected load has per phase impedance of (25+j40). If 400V, 3 supply is
connected to this load, find (i) phase current (ii) line current (iii) power supplied to the load.
Z ph = 252 + 40 2 = 47.17
40
= tan 1 = 60o
25
Z ph = 47.1760o
E L = 400V = E ph
(i ) I ph =
E ph
Z ph
400
= 8.48 60o A
o
47.1760
(ii ) I L = 3I ph = 3 8.48 = 14.7 90o A

(iii) P = 3E L I L cos = 3 400 14.7 cos 60o
P = 5397.76W
Problem 2
Two wattmeter method is used to measure the power absorbed by a 3 induction motor. The
wattmeter readings are 12.5kW and -4.8kW. Find (i) the power absorbed by the machine (ii) load
power factor (iii) reactive power taken by the load.
W1 = 12.5kW
W2 = 4.8kW
(i) P = W1 + W2 = 12.5 4.8 = 7.7kW
W W1
4.8 12.5
= 3
(ii) tan = 3 2
= 3.89
12.5 4.8
W1 + W2
= tan 1 [ 3.89] = 75.6o
pf = cos = cos 75.6o = 0.2487

(iii)Q = 3 (W2 W1 ) = 3 ( 4.8 12.5) = 29.96kVAR
Problem 3
Calculate the active and reactive components of each phase of a star connected 10kV, 3 alternator
supplying 5MW at 0.8 pf.
EL = 10kV
P = 5MW
pf = cos = 0.8
= 36.87 o
P = 3EL I L cos
IL =
P
5 106
=
= 360.84 A
3 10 103 0.8
3E L cos
5 106
= 166.7 MW
3
10 10
Q ph = E ph I ph sin =
360.8 sin 36.87 o = 1.25MVAR
3
Pph =
Problem 4
A 3 load of three equal impedances connected in delta across a balanced 400V supply takes a line
current of 10A at a power factor of 0.7 lagging. calculate (i) the phase current (ii) the total power (iii)
the total reactive kVAR
E L = 400V = E ph
I L = 10 A
pf = cos = 0.7lag
= 45.57 o
I
10
(i ) I ph = L =
= 5.8 A
3
3
(ii ) P = 3E L I L cos = 3 400 10 0.7 = 4.84kW
(iii )Q = 3EL I L sin = 3 400 10 sin 45.57 o = 4.94kVAR
Problem 5
The power flowing in a 3, 3 wire balanced load system is measured by two wattmeter method. The
reading in wattmeter A is 750W and wattmeter B is 1500W. What is the power factor of the system?
W1 = 750W
W2 = 1500W
W W1
1500 750
= tan 1 3
= tan 1 3 2
750 + 1500
W1 + W2
= 30o
pf = cos = cos 30o = 0.866
Problem 6
A 3 star connected supply with a phase voltage of 230V is supplying a balanced delta connected
load. The load draws 15kW at 0.8pf lagging. Find the line currents and the current in each phase of
the load. What is the load impedance per phase.
Alternator
E ph = 230V
EL = 3 230V = 398.37V
P = 15kW
pf = cos = 0.8lagging
P
= 27.17 A
3EL cos
IL =
Load
E ph = EL = 398.37V
I L = 27.17 A
IL
= 15.68 A
3
E ph
=
= 25.4
I ph
I ph =
Z ph

Basic Electrical Notes

Uploaded by

Copyright:

Available Formats

Basic Electrical Notes

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Basic Electrical Notes

Uploaded by

Copyright:

Available Formats

You can get more notes here: http://vtunotes.kwatle.

SINGLE PHASE AC CIRCUITS

2. Time Period (T)

You can get more notes here: http://vtunotes.kwatle.com

Advantages of AC system over DC system

Generation of sinusoidal AC voltage

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

Average value of a sinusoidal current

Average value of a full wave rectifier output

You can get more notes here: http://vtunotes.kwatle.com

Average value of a half wave rectifier output

RMS or Effective Value

Area under squared

You can get more notes here: http://vtunotes.kwatle.com

RMS value of a sinusoidal current

RMS value of a full wave rectifier output

RMS value of a half wave rectifier output

You can get more notes here: http://vtunotes.kwatle.com

Peak Factor or Crest Factor

For a sinusoidal waveform

For a Full Wave Rectifier Output

You can get more notes here: http://vtunotes.kwatle.com

For a Half Wave Rectifier Output

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

AC circuit with a pure resistance

You can get more notes here: http://vtunotes.kwatle.com

p = (Vm sin t )( I m sin t )

You can get more notes here: http://vtunotes.kwatle.com

Phasor Algebra for a pure resistive circuit

You can get more notes here: http://vtunotes.kwatle.com

AC circuit with a pure inductance

You can get more notes here: http://vtunotes.kwatle.com

It is equivalent to resistance in a resistive circuit. The unit is ohms ()

p = (Vm sin t )( I m sin(t / 2))

You can get more notes here: http://vtunotes.kwatle.com

Phasor algebra for a pure inductive circuit

You can get more notes here: http://vtunotes.kwatle.com

(iii )Vm = 2V = 325.27V

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

It is equivalent to resistance in a resistive circuit. The unit is ohms ()

You can get more notes here: http://vtunotes.kwatle.com

Phasor algebra in a pure capacitive circuit

You can get more notes here: http://vtunotes.kwatle.com

(iii )Vm = 2V = 325.27V

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

p = (Vm sin t )( I m sin(t )

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com

2. Power Factor cos =

4. Whether current leads or lags behind the voltage

You can get more notes here: http://vtunotes.kwatle.com

You can get more notes here: http://vtunotes.kwatle.com