G3 PDF

ORDER NO.
DSC1106032CE
B26
Digital Camera/Lens Kit/Double Zoom Lens Kit/Body

Model No. DMC-G3KPP
DMC-G3KPC
DMC-G3KEB
DMC-G3KEC
DMC-G3KEE
DMC-G3KEG
DMC-G3KGC
DMC-G3KGD
DMC-G3KGH
DMC-G3KGK
DMC-G3KGN
DMC-G3KGT
DMC-G3PP
DMC-G3PC
DMC-G3EB
DMC-G3EC
DMC-G3EE
DMC-G3EG
DMC-G3GC
DMC-G3GD
DMC-G3GH
DMC-G3GN
Panasonic Corporation 2011 Unauthorized copying and distribution is a violation of law.
DMC-G3GT
DMC-G3WGC
DMC-G3WGD
DMC-G3WGH
DMC-G3WGK
DMC-G3WGN
DMC-G3WGT
DMC-G3WPP
DMC-G3WEB
DMC-G3WEC
DMC-G3WEE
DMC-G3WEG
Vol. 1
Colour
[DMC-G3K]
(K)...........Black Type
(R)...........Red Type (except GD/GT)
(W)..........White Type (except PC/EG)
(T)...........Brown Type (only PP/EG/GC)
[DMC-G3W]
(R)...........Red Type (except PP/EE/GD/GT)
(W)..........White Type (except PP/EB/EE/EG)
(T)...........Brown Type (only EG/GC)
(KA).........Black Type (only EB)
[DMC-G3]
DMC-G3K series: Interchangeable Lens (H-FS014042) is bundled.
DMC-G3W series: Interchangeable Lens (H-FS014042/H-FS045200) are bundled.
DMC-G3 series: Camera Body Only.
TABLE OF CONTENTS
PAGE
1 Safety Precautions -----------------------------------------------3
1.1. General Guidelines ----------------------------------------3
1.2. Leakage Current Cold Check ---------------------------3
1.3. Leakage Current Hot Check (See Figure 1.)--------3
1.4. How to Discharge the E. Capacitor on Flash
P.C.B.----------------------------------------------------------4
2 Warning --------------------------------------------------------------5
2.1. Prevention of Electrostatic Discharge (ESD)
to Electrostatically Sensitive (ES) Devices ----------5
2.2. How to Recycle the Lithium Ion Battery (U.S.
Only)-----------------------------------------------------------5
2.3. Caution for AC Cord (For EB/GC/GH) ----------------6
2.4. How to Replace the Lithium Battery -------------------7
3 Service Navigation------------------------------------------------8
3.1. Introduction --------------------------------------------------8
3.2. Important Notice --------------------------------------------8
3.3. General Description About Lead Free Solder
(PbF) -------------------------------------------------------- 12
3.4. How to Define the Model Suffix (NTSC or PAL
model)------------------------------------------------------- 13
4 Specifications ---------------------------------------------------- 17
5 Location of Controls and Components------------------ 18
6 Service Mode ----------------------------------------------------- 22
6.1. Error Code Memory Function ------------------------- 22
PAGE
7 Troubleshooting Guide --------------------------------------- 24
7.1. Checking
Method
of
Body
and
Interchangeable Lens ---------------------------------- 24
8 Service Fixture & Tools--------------------------------------- 29
8.1. Service Fixture and Tools------------------------------ 29
8.2. Clean Box-------------------------------------------------- 30
8.3. Service Position ------------------------------------------ 31
9 Disassembly and Assembly Instructions -------------- 32
9.1. Camera Body Part--------------------------------------- 32
9.2. Disassembly and Assemble Procedure for the
Lens (H-FS014042) ------------------------------------- 43
9.3. Disassembly and Assemble Procedure for the
Lens (H-FS045200) ------------------------------------- 44
10 Measurements and Adjustments -------------------------- 45
10.1. Matrix Chart for Replaced Part and Necessary
Adjustment ------------------------------------------------ 45
11 Maintenance------------------------------------------------------ 47
11.1. Notice in external cleaning ---------------------------- 47
11.2. General
description
(Lens
cleaning:
Interchangeable Lens/H-FS014042)---------------- 48
11.3. General
description
(Lens
cleaning:
Interchangeable Lens/H-FS045200)---------------- 51
1 Safety Precautions
1.1.
General Guidelines
1.3.
1. IMPORTANT SAFETY NOTICE

There are special components used in this equipment
which are important for safety. These parts are marked by
2.
3.
4.
5.
1. Plug the AC cord directly into the AC outlet. Do not use

an isolation transformer for this check.
2. Connect a 1.5 k, 10 W resistor, in parallel with a 0.15 F
capacitor, between each exposed metallic part on the set
and a good earth ground, as shown in Figure 1.
3. Use an AC voltmeter, with 1 k/V or more sensitivity, to
measure the potential across the resistor.
4. Check each exposed metallic part, and measure the voltage at each point.
5. Reverse the AC plug in the AC outlet and repeat each of
the above measurements.
6. The potential at any point should not exceed 0.75 V RMS.
A leakage current tester (Simpson Model 229 or equivalent) may be used to make the hot checks, leakage current must not exceed 1/2 mA. In case a measurement is
outside of the limits specified, there is a possibility of a
shock hazard, and the equipment should be repaired and
rechecked before it is returned to the customer.
in the Schematic Diagrams, Circuit Board Layout,

Exploded Views and Replacement Parts List. It is essential that these critical parts should be replaced with manufacturers specified parts to prevent X-RADIATION,
shock, fire, or other hazards. Do not modify the original
design without permission of manufacturer.
An Isolation Transformer should always be used during
the servicing of AC Adaptor whose chassis is not isolated
from the AC power line. Use a transformer of adequate
power rating as this protects the technician from accidents resulting in personal injury from electrical shocks. It
will also protect AC Adaptor from being damaged by accidental shorting that may occur during servicing.
When servicing, observe the original lead dress. If a short
circuit is found, replace all parts which have been overheated or damaged by the short circuit.
After servicing, see to it that all the protective devices
such as insulation barriers, insulation papers shields are
properly installed.
After servicing, make the following leakage current
checks to prevent the customer from being exposed to
shock hazards.
1.2.
Leakage Current Hot Check

(See Figure 1.)
Leakage Current Cold Check
1. Unplug the AC cord and connect a jumper between the

two prongs on the plug.
2. Measure the resistance value, with an ohmmeter,
between the jumpered AC plug and each exposed metallic cabinet part on the equipment such as screwheads,
connectors, control shafts, etc. When the exposed metallic part has a return path to the chassis, the reading
should be between 1 M and 5.2 M. When the exposed
metal does not have a return path to the chassis, the
reading must be infinity.
Figure. 1
1.4.
How to Discharge the E. Capacitor on Flash P.C.B.
CAUTION:
1. Be sure to discharge the E. Capacitor on FLASH P.C.B..
2. Be careful of the high voltage circuit on FLASH P.C.B. when servicing.
[Discharging Procedure]
1. Refer to the disassemble procedure and remove the necessary parts/unit.
2. Put the insulation tube onto the lead part of Resistor (ERG5SJ102:1k /5W).
(An equivalent type of resistor may be used.)
3. Put the resistor between both terminals of E. Capacitor on FLASH P.C.B. for approx. 5 seconds.
4. After discharging, confirm that the E. Capacitor voltage is lower than 10V by using a voltmeter.
Fig. F1
2 Warning
2.1.
Prevention of Electrostatic Discharge (ESD) to Electrostatically

Sensitive (ES) Devices
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such components commonly are called Electrostatically Sensitive (ES) Devices.
The following techniques should be used to help reduce the incidence of component damage caused by electrostatic discharge
(ESD).
1. Immediately before handling any semiconductor component or semiconductor-equipped assembly, drain off any ESD on your
body by touching a known earth ground. Alternatively, obtain and wear a commercially available discharging ESD wrist strap,
which should be removed for potential shock reasons prior to applying power to the unit under test.
2. After removing an electrical assembly equipped with ES devices, place the assembly on a conductive surface such as aluminum foil, to prevent electrostatic charge buildup or exposure of the assembly.
3. Use only a grounded-tip soldering iron to solder or unsolder ES devices.
4. Use only an antistatic solder removal device. Some solder removal devices not classified as "antistatic (ESD protected)" can
generate electrical charge sufficient to damage ES devices.
5. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ES devices.
6. Do not remove a replacement ES device from its protective package until immediately before you are ready to install it. (Most
replacement ES devices are packaged with leads electrically shorted together by conductive foam, aluminum foil or comparable conductive material).
7. Immediately before removing the protective material from the leads of a replacement ES device, touch the protective material
to the chassis or circuit assembly into which the device will be installed.
CAUTION :
Be sure no power is applied to the chassis or circuit, and observe all other safety precautions.
8. Minimize bodily motions when handling unpackaged replacement ES devices. (Otherwise harmless motion such as the
brushing together of your clothes fabric or the lifting of your foot from a carpeted floor can generate static electricity (ESD) sufficient to damage an ES device).
2.2.
How to Recycle the Lithium Ion Battery (U.S. Only)
2.3.
2.3.1.
Caution for AC Cord

(For EB/GC/GH)
2.3.2.1.
Information for Your Safety

Blue
Brown
IMPORTANT
Your attention is drawn to the fact that recording of prerecorded tapes or discs or other published or broadcast
material may infringe copyright laws.
WARNING
To reduce the risk of fire or shock hazard, do not expose
this equipment to rain or moisture.
CAUTION
To reduce the risk of fire or shock hazard and annoying
interference, use the recommended accessories only.
FOR YOUR SAFETY
DO NOT REMOVE THE OUTER COVER
To prevent electric shock, do not remove the cover. No user
serviceable parts inside. Refer servicing to qualified service
personnel.
2.3.2.
Important
The wires in this mains lead are coloured in accordance with

the following code:
Neutral
Live
As the colours of the wires in the mains lead of this appliance

may not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or coloured
BLACK.
The wire which is coloured BROWN must be connected to the
terminal in the plug which is marked with the letter L or coloured
RED.
Under no circumstances should either of these wires be connected to the earth terminal of the three pin plug, marked with
the letter E or the Earth Symbol.
Caution for AC Mains Lead
For your safety, please read the following text carefully.

This appliance is supplied with a moulded three-pin mains plug
for your safety and convenience.
A 5-ampere fuse is fitted in this plug.
Should the fuse need to be replaced please ensure that the
replacement fuse has a rating of 5 amperes and it is approved
by ASTA or BSI to BS1362
Check for the ASTA mark or the BSI mark on the body of the
fuse.
2.3.2.2.
Before Use
Remove the Connector Cover as follows.
If the plug contains a removable fuse cover you must ensure

that it is refitted when the fuse is replaced.
If you lose the fuse cover, the plug must not be used until a
replacement cover is obtained.
A replacement fuse cover can be purchased from your local
Panasonic Dealer.
2.3.2.3.
How to Replace the Fuse
1. Remove the Fuse Cover with a screwdriver.
If the fitted moulded plug is unsuitable for the socket outlet in

your home then the fuse should be removed and the plug cut
off and disposed of safety.
There is a danger of severe electrical shock if the cut off plug is
inserted into any 13-ampere socket.
If a new plug is to be fitted please observe the wiring code as
shown below.
If in any doubt, please consult a qualified electrician.
2. Replace the fuse and attach the Fuse cover.
2.4.
2.4.1.
How to Replace the Lithium Battery

Replacement Procedure
1. Remove the MAIN P.C.B.. (Refer to Disassembly Procedures.)

2. Unsolder the each soldering point of electric lead terminal for Lithium battery (Ref. No. B9110 at foil side of MAIN P.C.B.) and
remove the Lithium battery together with electric lead terminal. Then replace it into new one.
NOTE:
The Type No. ML421 includes electric lead terminals.
NOTE:
This Lithium battery is a critical component.
(Type No.: ML421 Manufactured by Energy Company, Panasonic Corporation.)
It must never be subjected to excessive heat or discharge.
It must therefore only be fitted in requirement designed specifically for its use.
Replacement batteries must be of same type and manufacture.
They must be fitted in the same manner and location as the original battery, with the correct polarity contacts observed.
Do not attempt to re-charge the old battery or re-use it for any other purpose.
It should be disposed of in waste products destined for burial rather than incineration.
NOTE:
Above caution is applicable for a battery pack which is for DMC-G3K/G3W/G3 series, as well.
3 Service Navigation
3.1.
Introduction
This service manual contains technical information, which allow service personnels to understand and service this model.
Please place orders using the parts list and not the drawing reference numbers.
If the circuit is changed or modified, the information will be followed by service manual to be controlled with original service manual.
3.2.
Important Notice
*When servicing, it is recommended dealing with Clean box. (Refer to "8.2. Clean Box" section of this service manual for details.)
3.2.1.
3.2.1.1.
Camera Body Unit

About VENUS FHD(IC6001) [Located on the Main P.C.B.]:
The VENUS FHD (IC6001) mounted on the Main P.C.B. consists of FLASH-ROM chip and VENUS chip, both chips are integrated as one-piece with soldered directly.
When replacing, always replace in pairs. (Units of service parts: integrated (one pair) state.)
NOTE:
During servicing, do not press down hard on the surface of IC6001.
Fig. S1
3.2.1.2.
About Mount Box Unit (Ref. 16)
1. This Service Manual does not contain the following repair service information for "MOUNT BOX UNIT"(Ref.16), because it
requires special facilities and equipment.
a. Schematic diagram, Block diagram and P.C.B. layout.
b. Parts list for individual parts.
2. If the "MOUNT BOX UNIT" is confirmed as defective, exchange the "MOUNT BOX UNIT" as a unit (supplied as service parts
size).
3. Before exchanging the "MOUNT BOX UNIT", the performances must be carefully checked, by following the "7.Troubleshooting Guide" section of this service manual.
Important:
1. After replacing the MOUNT BOX UNIT, the mount box data has to be stored to the unit.
The mount box unit supplied as service parts has affix the label of own configure data.
By inputting these data into the adjustment software and writting these data to VENUS FHD (IC6001), the shutter adjustment
becomes needless.
In addition, the adjustment software can read data encoded to QR code by using WEB camera with a close-up function.
Refer to the adjustment instruction in the adjustment software for details.
Fig. S2
2. The full adjustment must be performed after replacing the "MOUNT BOX UNIT", otherwise picture quality can not be meet
with specification.
3.2.1.3.
About Flexible Cable and Connector
Do not touch carelessly so that the foreign body should not adhere to the terminal part of flexible cable and connector.
Wipe off with a clean cloth and the cotton bud, etc. when the terminal part is dirty.
3.2.1.4.
About Main P.C.B. (Ref. 1) / LCD IF P.C.B. (Ref. 40)
1. This Service Manual does not contain the following repair service information for MAIN P.C.B.(Ref.1) and LCD IF
P.C.B.(Ref.40), because it requires special facilities and equipment.
a. Schematic diagram, Block diagram and P.C.B. layout.
b. Parts list for individual parts.
2. When a part replacement is required for repairing MAIN P.C.B. and LCD IF P.C.B., replace as an assembled P.C.B. parts.
As for handling the defected P.C.B.s, contact the sales company service depart.
*MAIN P.C.B. (VEP56135A: PP/PC/EE/GC/GD/GH/GK/GN/GT)
*MAIN P.C.B. (VEP56135B: EB/EC/EG)
*LCD IF P.C.B. (VEP59096A)
Important (About Main P.C.B.):
1. Before exchange the "MAIN P.C.B.", the performances must be carefully checked, by following the "7.Troubleshooting Guide"
section of this service manual.
2. Before replacing the "MAIN P.C.B.", proceed the EEPROM data backup from the unit. After replacing the MAIN P.C.B., overwrite the EEPROM data with backup data from the unit first, then proceed the adjustment /inspection.
If it is impossible to make a data backup due to the unit does not turns on the power and so on, additional adjustment (using
the light box) is required.
3. The full adjustment must be performed after replacing the "MAIN P.C.B.", otherwise Picture quality can not be meet with specification.
3.2.2.
3.2.2.1.
Lens Unit (Interchangeable Lens: H-FS014042)

About Lens Main Block Unit (Ref. 208)
1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.208), because it
2. The "LENS MAIN BLOCK UNIT"(Ref.208) performance must be confirmed.
3. In case of the "LENS MAIN BLOCK UNIT"(Ref.208) defect, contact to the service department of sales company.
Fig. S3
10
3.2.3.
3.2.3.1.
Lens Unit (Interchangeable Lens: H-FS045200)

About Lens Main Block Unit (Ref. 308)
1. This Service Manual does not contain the repair service information for "LENS MAIN BLOCK UNIT"(Ref.308), because it
2. The "LENS MAIN BLOCK UNIT"(Ref.308) performance must be confirmed.
3. In case of the "LENS MAIN BLOCK UNIT"(Ref.308) defect, contact to the service department of sales company.
Fig. S4
11
3.3.
General Description About Lead Free Solder (PbF)
The lead free solder has been used in the mounting process of all electrical components on the printed circuit boards used for this
equipment in considering the globally environmental conservation.
The normal solder is the alloy of tin (Sn) and lead (Pb). On the other hand, the lead free solder is the alloy mainly consists of tin
(Sn), silver (Ag) and Copper (Cu), and the melting point of the lead free solder is higher approx.30C (86F) more than that of the
normal solder.
Distinction of P.C.B. Lead Free Solder being used
Service caution for repair work using Lead Free Solder (PbF)
The lead free solder has to be used when repairing the equipment for which the lead free solder is used.
(Definition: The letter of PbF is printed on the P.C.B. using the lead free solder.)
To put lead free solder, it should be well molten and mixed with the original lead free solder.
Remove the remaining lead free solder on the P.C.B. cleanly for soldering of the new IC.
Since the melting point of the lead free solder is higher than that of the normal lead solder, it takes the longer time to melt the
lead free solder.
Use the soldering iron (more than 70W) equipped with the temperature control after setting the temperature at 35030C
(66286F).
Recommended Lead Free Solder (Service Parts Route.)
The following 3 types of lead free solder are available through the service parts route.
RFKZ03D01KS-----------(0.3mm 100g Reel)
RFKZ06D01KS-----------(0.6mm 100g Reel)
RFKZ10D01KS-----------(1.0mm 100g Reel)
Note
* Ingredient: tin (Sn) 96.5%, silver (Ag) 3.0%, Copper (Cu) 0.5%, Cobalt (Co) / Germanium (Ge) 0.1 to 0.3%
12
3.4.
How to Define the Model Suffix (NTSC or PAL model)
There are eight kinds of DMC-G3 (Camera body unit), regardless of the colours.
a) DMC-G3 (Japan domestic model)
b) DMC-G3PP/PC
c) DMC-G3EB/EC/EG/GH/GN
d) DMC-G3EE
e) DMC-G3GK
f) DMC-G3GT
g) DMC-G3GD
h) DMC-G3GC
What is the difference is that the INITIAL SETTINGS data which is stored in VENUS FHD mounted on MAIN P.C.B..
3.4.1.
Defining methods:
To define the model suffix to be serviced, refer to the nameplate which is putted on the bottom side of the Unit.
NOTE:
After replacing the MAIN P.C.B., be sure to achieve adjustment.
13
3.4.2.
INITIAL SETTINGS:
After replacing the MAIN P.C.B., make sure to perform the initial settings after achieving the adjustment by ordering the following
procedure in accordance with model suffix of the unit.
1. IMPORTANT NOTICE:
Before proceeding Initial settings, make sure to read the following CAUTION.
2. PROCEDURES:
Precautions: Read the above CAUTION carefully.
Preparation:
Attach the fully charged Battery, and insert the SD memory card.
Confirm that it is not intelligent auto mode [iA] or intelligent auto plus mode [iA+].
NOTE:
If the unit is intelligent auto mode [iA] or intelligent auto plus mode [iA+], it does not display the initial settings menu.
Step 1. The temporary cancellation of INITIAL SETTINGS:
While pressing [ Q.MENU/Fn2 ], [ DISP/Fn1 ] and [ RIGHT ] of Cursor buttons simultaneously, turn the Power on.
Step 2. The cancellation of INITIAL SETTINGS:
Press the [ PLAYBACK ] button, then playback the picture.
Press [ Q.MENU/Fn2 ] and [ UP ] of Cursor buttons simultaneously, then turn the Power off.
Step 3. Turn the Power on:
SEt the mode dial to [ P ] (Program AE Mode), then turn the Power on.
Step 4. Display the INITIAL SETTING:
While pressing [ RIGHT ] of Cursor buttons and [ MENU/SET ] simultaneously, turn the Power off.
The INTIAL SETTINGS menu is displayed.
There are two kinds of INITIAL SETTINGS menu form as follows:
[CASE 1. After replacing MAIN P.C.B.]
[Except "EG, EB, EC and OLY" models : (VEP56135A is used as a Main P.C.B.)]
When MAIN P.C.B. has just been replaced, all of the model suffix are displayed as follows. (two pages in total)
14
[Only for "EG, EB EC and OLY" models : (VEP56135B is used as a Main P.C.B.)]
When MAIN P.C.B. has just been replaced, only 4 model suffix are displayed as follows.
[CASE 2. Other than "After replacing MAIN P.C.B."]
Step 5. Choose the model suffix in INITIAL SETTINGS: (Refer to CAUTION)

[Caution: After replacing MAIN P.C.B.]
The model suffix can been chosen, JUST ONE TIME.
Once one of the model suffix have been chosen, the model suffix lists will not be displayed, thus, it can be changed.
Therefore, select the area carefully.
Select the area with pressing [ UP ] / [ DOWN ] of Cursor buttons.
Step 6. Set the model suffix in INITIAL SETTINGS:
- Press the [ RIGHT ] of Cursor buttons.
- The only set area is displayed, and then press the [ RIGHT ] of Cursor buttons after confirmation.
(The unit is powered off automatically.)
15
Step 7. CONFIRMATION:
Confirm the display of PLEASE SET THE CLOCK in concerned language when the unit is turned on again.
When the unit is connected to PC with USB cable, it is detected as removable media.
(When the GT or GK model suffix is selected, the display shows PLEASE SET THE CLOCK in Chinese.)
1) As for your reference, major default setting condition is as shown in the following table.
Default setting (After INITIAL SETTINGS)
a)
b)
c)
d)
e)
f)
g)
h)
i)
j)
k)
l)
m)
MODEL
DMC-G3 (Japan domestic model)
DMC-G3PP
DMC-G3PC
DMC-G3EB
DMC-G3EC
DMC-G3EE
DMC-G3EG
DMC-G3GC
DMC-G3GD
DMC-G3GH
DMC-G3GK
DMC-G3GN
DMC-G3GT
VIDEO OUTPUT
NTSC
NTSC
NTSC
PAL
PAL
PAL
PAL
PAL
NTSC
PAL
PAL
PAL
NTSC
16
LANGUAGE
Japanese
English
English
English
English
Russian
English
English
Korean
English
Chinese (simplified)
English
Chinese (Traditional)
DATE
Year/Month/Date
Month/Date/Year
Month/Date/Year
Date/Month/Year
Date/Month/Year
Date/Month/Year
Date/Month/Year
Date/Month/Year
Year/Month/Date
Date/Month/Year
Year/Month/Date
Date/Month/Year
Year/Month/Date
REMARKS
4 Specifications
17
5 Location of Controls and Components

Names and Functions of Components
1
2
3
4
5
6
7
Camera body
Sensor
Flash
Self-timer indicator /
AF Assist Lamp
Lens fitting mark
Mount
Lens lock pin
Lens release button
1 2
4 5
8
9
10
11
12
13
14
15
16
17
18
[LVF/LCD] button
8 9 10 11 12 13 14 15
Diopter adjustment dial
Viewfinder
Playback button
Motion picture button
Camera ON/OFF switch
Rear dial
[DISP./Fn1] button
Eye Cup
Touch panel/LCD monitor
[Q.MENU/Fn2] button /
16 17
18 19 20
Delete/Return button
19 [MENU/SET] button
20 Cursor buttons
/ISO
/WB (White Balance)
/AF Mode button
/[DRIVE MODE] button
This button in picture record mode will allow the user to select between the following
options.
Single /Burst /Auto bracket /Self-timer
18
21 Shoulder strap eyelet

Be sure to attach the shoulder strap when
using the camera to ensure that you will not
drop it.
21
22
23
24
22 [REMOTE] socket
23 [HDMI] socket
24 [AV OUT/DIGITAL] socket
25
26
27
28
29
30
31
32
33
Focus distance reference mark

Stereo microphone
Shutter button
Speaker
Flash open lever
Hot shoe
Mode dial
Status indicator
Intelligent Auto button
25
27
26
28 29 30
31 32 33
34
35 36 37
34 Tripod receptacle
35 DC coupler cover
When using an AC adaptor, ensure that the
Panasonic DC coupler (optional) and AC
adaptor (optional) are used.
36 Release lever
37 Card/Battery door
Lens
H-FS045200
(LUMIX G VARIO 45 200 mm/F4.0 5.6/
MEGA O.I.S.)
H-FS014042
(LUMIX G VARIO 14 42 mm/F3.5 5.6
ASPH./MEGA O.I.S.)
42
38
38
39
40
41
42
43
44
45
39 40 41 42
43
44
38
Tele
Lens surface
Focus ring
Wide
Zoom ring
Contact point
Lens fitting mark
[O.I.S.] switch
19
39
41
40 45
43 44
Selecting the Recording Mode

To select a Recording Mode with the mode dial
Switching the mode by rotating the mode dial.

Align a desired mode with part .
Rotate the mode dial slowly and surely to adjust to each mode.
To select Intelligent Auto Mode
Press [}].
[}] button will light up when it is switched to Intelligent Auto Mode.
The Recording Mode selected by the mode dial is disabled while the [}]
button is lit.
Basic
Intelligent Auto Mode
The subjects are recorded using settings automatically selected by the camera.
Program AE Mode
The subjects are recorded using your own settings.
Advanced
Aperture-Priority AE Mode
The shutter speed is automatically determined by the aperture value you set.
Shutter-Priority AE Mode
The aperture value is automatically determined by the shutter speed you set.
Manual Exposure Mode
The exposure is adjusted by the aperture value and the shutter speed which are
manually adjusted.
Custom Mode
Use this mode to take pictures with previously registered settings.
Scene Mode
This allows you to take pictures that match the scene being recorded.
Creative Control Mode
Record while checking the image effect.
20
Touch Panel
This touch panel is a type that detects pressure.
Touch the screen
Drag
To touch and release the touch panel.
A movement without releasing the touch

panel.
Use this to perform tasks such as selecting

icons or images displayed on the touch
panel.
When selecting features using the touch
This is used to move the AF area, operate

the slide bar, etc.
This can also be used to move to the next
image during playback, etc.
panel, be sure to touch the center of the

desired icon.
Note
If you use a commercially available liquid crystal protection
sheet, please follow the instructions that accompany the sheet.
(Some liquid crystal protection sheets may impair visibility or
operability.)
If a commercially available protection sheet is used, a little extra
pressure may be required if you notice that the touch panel is
not responsive.
Avoid having the hand holding the camera accidently apply
pressure to the touch panel. Doing so may affect the touch panel
operation.
Do not press on the LCD monitor with hard pointed tips, such as
ball point pens.
Do not operate with your fingernails.
Wipe the LCD monitor with dry soft cloth when it gets dirty with finger prints and others.
Do not scratch or press the LCD monitor too hard.
For information about the icons displayed on the touch panel.
About the Stylus pen

It is easier to use the stylus pen (supplied) for detailed operation or if it is hard to operate
with your fingers.
Only use the supplied stylus pen.
Do not place it where small children can reach.
21
6 Service Mode
6.1.
Error Code Memory Function
1. General description
This unit is equipped with history of error code memory function, and can be memorized 16 error codes in sequence from the
latest. When the error is occurred more than 16, the oldest error is overwritten in sequence.
The error code is not memorized when the power supply is shut down forcibly.
(i.e., when the unit is powered on by the battery, the battery is pulled out)
The error code is memorized to FLASH-ROM when the unit has just before powered off.
2. How to display
The error code can be displayed by ordering the following procedure:
Preparation
Attach the fully charged Battery, and insert the SD memory card.
Confirm that it is not intelligent auto mode [iA] or intelligent auto plus mode [iA+].
NOTE:
If the unit is intelligent auto mode [iA] or intelligent auto plus mode [iA+], it does not display the initial settings menu.
Step 1. The temporary cancellation of INITIAL SETTINGS:
While pressing [ Q.MENU/Fn2 ], [ DISP/Fn1 ] and "[ RIGHT ] of Cursor buttons" simultaneously, turn the Power on.
Step 2. Execute the error code display mode:
Press [ Q.MENU/Fn2 ], [ MENU/SET ] and "[ LEFT ] of Cursor buttons" simultaneously with the step 1 condition.
The display is changed as shown below when the above buttons are pressed simultaneously.
Normal display Error code display Camera information display Normal display .....
Example of Error Code Display
22
Error Code List:

The error code consists of 8 bit data and it shows the following information.
Important notice about Error Code List

About "*" indication:
The third digit from the left is different as follows.
- In case of 0 (example: 2B001000)
When the third digit from the left shows 0, this error occurred under the condition of INITIAL SETTINGS has been completed.
It means that this error is occurred basically at user side.
- In case of 8 (example: 2B801000)
When the third digit from the left shows "8", this error occurred under the condition of INITIAL SETTINGS has been
released.
(Example; Factory assembling-line before unit shipment, Service mode etc.)
It means that this error is occurred at service side.
Step 3. How to exit from Error Code display mode:
Simply, turn the power off. (Since Error Code display mode is executed under the condition of temporary cancellation of
INITIAL SETTINGS, it wake up with normal condition when turn off the power.)
NOTE:
The error code can not be initialized.
23
7 Troubleshooting Guide
7.1.
Checking Method of Body and Interchangeable Lens
24
25
26
27
28
8 Service Fixture & Tools

8.1.
Service Fixture and Tools
The following Service Fixture and tools are used for checking and servicing this unit.
29
8.2.
Clean Box
The repair quality is considered, and it is recommended working in the environment of satisfied clean level less than class 10,000
(Federal Standard 209D).
(When remove the 1st lens frame, it is indispensable.)
[NOTE]
Work in the environment of satisfied clean level less than class 10,000 (Federal Standard 209D) when remove the 1st lens frame
for cleaning.
*Refer to "11.2. General description (Lens cleaning: Interchangeable Lens/H-FS014042)", "11.3. General description (Lens
cleaning: Interchangeable Lens/H-FS045200)" section of this service manual for details.
30
8.3.
Service Position
This Service Position is used for checking and replacing parts. Use the following Extension cables for servicing.
Table S1 Extension Cable List
No.
1
2
3
4
5
6
7
8
9
10
11
Parts No.
RFKZ0583
RFKZ0477
VFK1976
RFKZ0393
RFKZ0583
RFKZ0477
RFKZ0477
RFKZ0477
RFKZ0583
RFKZ0564
VFK1480
Connection
FP9007(MAIN) - HOT SHOE FPC
FP9003(MAIN) - LVF UNIT
FP9005(MAIN) - FPCFP8001(TOP)
FP9010(MAIN) - FPCFP4202(MIC)
FP9006(MAIN) - MOUNT BOX UNIT(SHUTTER)
FP9004(MAIN) - LCD UNIT
FP3912(MAIN) - MOUNT BOX UNIT
FP3913(MAIN) - MOUNT BOX UNIT
FP9009(MAIN) - FPCFP8501(FLASH)
FP9001(MAIN) - MOUNT BOX UNIT(LENS I/F)
FP9008(MAIN) - REAR OPERATION UNIT
Form
19PIN 0.3 FFC
45PIN 0.3 FFC
19PIN 0.5 FFC
15PIN 0.3 FFC
19PIN 0.3 FFC
45PIN 0.3 FFC
45PIN 0.3 FFC
45PIN 0.3 FFC
19PIN 0.3 FFC
23PIN 0.3 FFC
6PIN 0.5 FFC
CAUTION-1. (When servicing FLASH P.C.B.)

1. Be sure to discharge the E.capacitor on FLASH P.C.B..
Refer to HOW TO DISCHARGE THE E.CAPACITOR ON FLASH P.C.B..
The E.capacitor voltage is not lowered soon even if the AC Cord is unplugged or the battery is removed.
2. Be careful of the high voltage circuit on FLASH P.C.B..
3. DO NOT allow other parts to touch the high voltage circuit on FLASH P.C.B..
31
9 Disassembly and Assembly Instructions

9.1.
9.1.1.
Camera Body Part

Disassembly Flow Chart
This is a disassembling chart.

When assembling, perform this chart conversely.
9.1.2.
P.C.B. Location
32
9.1.3.
Disassembly Procedure
No.
Item
1
Rear Case Unit
Fig
(Fig. D1)
(Fig. D2)
(Fig. D3)
Main P.C.B.
Front Case Unit
(Fig. D4)
(Fig. D5)
(Fig. D6)
(Fig. D7)
Mount Box Unit
(Fig. D8)
Top Case Unit
(Fig. D9)
Flash P.C.B.
(Fig. D10)
Battery Door Unit
(Fig. D11)
(Fig. D12)
Battery Case
(Fig. D13)
LVF Unit
(Fig. D14)
10
Top P.C.B.
(Fig. D15)
11
Mic P.C.B.
(Fig. D16)
No.
Item
12 Rear Earth Plate
Removal
4 Screws (A)
8 Screws (B)
Side Ornament R
Side Ornament L
Jack Door
Eye Rubber
2 Screws (C)
FP9004(Flex)
FP9008(Flex)
Rear Case Unit
1 Screw (D)
3 Screws (E)
FP9003(Flex)
2 Tapes (A)
1 Tape (B)
FP3911(Flex)
FP3912(Flex)
FP3913(Flex)
FP9001(Flex)
FP9002(Flex)
FP9005(Flex)
FP9006(Flex)
FP9007(Flex)
FP9009(Flex)
FP9010(Flex)
Main P.C.B.
2 Screws (F)
2 Screws (G)
Front Case Unit
4 Screws (H)
Mount Box Unit
2 Screws (I)
5 Locking tabs
Capacitor PCB Cover
P8502(Connector)
P8503(Connector)
Top Case Unit
1 Screw (J)
1 Screw (K)
Tape
Flash P.C.B.
Caution for Discharging
Battery Door Shaft
Battery Door Spring
Battery Door Unit
2 Locking tabs
Heat Radiation Plate
3 Locking tabs
Battery Out Spring
Battery Lock Knob
Battery Lock Spring
Battery Case
2 Screws (L)
LVF Unit
2 Screws (M)
FP8002(Flex)
Multi-Button Switch
1 Screw (N)
Top P.C.B.
FP4201(Flex)
FP4202(Flex)
1 Screw (O)
Mic P.C.B.
13
14
15
16
33
Fig
Removal
(Fig. D17) 4 Screws (P)
1 Screw (Q)
2 Screws (R)
(Fig. D18) Grip Piece Rear
2 Locking tabs
Arm Cover Top
Arm Cover Bottom
Rear Earth Plate
Rear Operation P.C.B. (Fig. D19) 1 Screw (S)
LCD Lock Holder
Rear Operation P.C.B.
Hinge SW FPC Unit
(Fig. D20) 2 Screws (T)
LCD Unit
1 Screw (U)
Flex
Hinge Plate
2 Screws (V)
(Fig. D21) 6 Ribs
Hinge SW FPC Unit
LCD Unit
LCD IF P.C.B.
(Fig. D22) 2 Screws (W)
2 Screws (X)
6 Locking tabs
LCD Case Bottom
LCD Hinge Unit
FP7202(Flex)
FP7203(Flex)
FP7204(Flex)
FP7205(Flex)
LCD PCB Sheet
LCD IF P.C.B.
LCD Unit
(Fig. D23) LCD BL Bezel Sheet
LCD Case Top
4 Locking tabs
Backlight Unit
LCD Unit
9.1.3.1.
Removal of the Rear Case Unit
(Fig. D1)
(Fig. D2)
34
9.1.3.2.
Removal of the Main P.C.B.
(Fig. D3)
(Fig. D4)
35
(Fig. D5)
9.1.3.3.
Removal of the Front Case Unit
(Fig. D7)
(Fig. D6)
36
9.1.3.4.
Removal of the Mount Box Unit
9.1.3.5.
Removal of the Top Case Unit
(Fig. D9)
9.1.3.6.
Removal of the Flash P.C.B.
(Fig. D8)
(Fig. D10)
37
9.1.3.8.
Removal of the Battery Case
(Fig. D11)
9.1.3.7.
Removal of the Battery Door Unit
(Fig. D12)
(Fig. D13)
38
9.1.3.9.
Removal of the LVF Unit
9.1.3.11. Removal of the Mic P.C.B.
(Fig. D16)
(Fig. D14)
9.1.3.12. Removal of the Rear Earth Plate
9.1.3.10. Removal of the Top P.C.B.
(Fig. D17)
(Fig. D15)
39
9.1.3.14. Removal of the Hinge SW FPC

Unit and LCD Unit
(Fig. D18)
9.1.3.13. Removal of the Rear Operation

P.C.B.
(Fig. D19)
(Fig. D20)
40
9.1.3.15. Removal of the LCD IF P.C.B.
(Fig. D21)
(Fig. D22)
41
9.1.3.16. Removal of the LCD Unit
(Fig. D23)
NOTE: (When Installing)

Make sure to confirm the following points when installing:
The Screw is tightened enough.
Installing conditions are fine. (No distortion, no abnormalspace.)
No dust and/or dirt on Lens surfaces.
LCD image is fine. (No dust and dirt on it, and no gradient
images.)
42
9.2.
Disassembly and Assemble Procedure for the Lens (H-FS014042)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to 8.2. Clean Box section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. K1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the 11 Maintenance for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. K1.
NOTE:
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, mentioned on the above table.
2. The Ref.B213 is no need to remove/install for disassembly and assembly.
If necessary, use VFK1390 (small driver) when screwing it.
Interchangeable Lens (H-FS014042)
(Fig. K1)
43
9.3.
Disassembly and Assemble Procedure for the Lens (H-FS045200)
It is recommended dealing with clean box, to keep maintaining the dustproof environment.
(Refer to 8.2. Clean Box section of this service manual for details.)
Important:
1. When servicing the enclosure part (refer to Fig. W1), it must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal Standard 209D))
As for procedure, refer to the 11 Maintenance for detailes.
2. To minimize the possibilities/risk of getting the dust/dirt on the lens surface, keep covering the lens unit with lens caps (front &
rear), other than necessary cases.
3. Do not touch the surface of the lens glasses with your fingers.
4. Blow off the dust on the surface of the lens with a blower brush.
5. Use lens cleaning KIT (BK)(VFK1900BK).
Proceed disassemble/assemble, by referring the following table and Fig. W1.
NOTE:
1. When installing the screws, be sure to use the torque driver (RFKZ0456) and tighten the screws with specified torque, mentioned on the above table.
2. The Ref.B309 is no need to remove/install for disassembly and assembly.
3. Use small driver (VFK1390) when removing/tighten the B308.
Interchangeable Lens (H-FS045200)
(Fig. W1)
44
10 Measurements and Adjustments

10.1. Matrix Chart for Replaced Part and Necessary Adjustment
The relation between Replaced part and Necessary Adjustment is shown in the following table.
When concerned part is replaced, be sure to achieve the necessary adjustment(s).
As for Adjustment condition/procedure, consult the Adjustment Manual which is available in Adjustment software.
NOTE:
After adjustments have been terminated, make sure to achieve INITIAL SETTINGS.
After updates it to the latest firmware, the adjustment is executed.
*1
Inspect it, not only corresponding part is replaced, but also camera body is shocked and/or dropped.
The Panasonic camera body in accordance with the Micro Four Thirds system (DMC-G1 unit, etc. marketed commodity: operates normal) and a standard zoom lens H-FS014045 (marketed commodity: operates normal) is required as a reference
machine.
*2 NOTE: (When exchange the MAIN P.C.B.)
Correspond by either the following when exchange the MAIN P.C.B. unavoidably by destruction and damage etc. of MAIN
P.C.B..
1. When it can turn on power, and the adjustment software can communicate with the camera body:
Before replacing, proceed the VENUS FHD (IC6001) data backup from the unit. After replacing, overwrite the VENUS FHD
(IC6001) data with backup data from the unit, before proceeding the main body adjustment.
2. When it cannot turn on power, or the adjustment software cannot communicate with the camera body:
The readjustment of mount box unit etc. are necessary.
45
*3 NOTE: (After exchange the mount box unit)

Execute the resolution inspection by the comparison with the standard model (DMC-G1K etc.: operates normal).
*4
Confirm self recording/playback motion picture of AVCHD mode by the LCD.
Confirm it on the TV with HDMI socket when repair HDMI relation.
* There are no LCD/LVF adjustment model.
*5 NOTE: (When AWB adjustment)

After change to WB adjustment mode for service with software, the adjustment is executed.
After adjusting the AWB adjustment, to cancel the WB adjustment mode for service.
Details, refer to the instructions in the adjustment software.
About the 3D interchangeable lens (H-FT012) correspondence

This unit has no special structure (circuit or part) for the 3D interchangeable lens correspondence, only by software is processed
the 3D interchangeable lens correspondence.
Therefore, if taken with other lenses as usual, the 3D interchangeable lens is no problem for operation.
46
11 Maintenance
11.1. Notice in external cleaning
11.1.1.
ABOUT THE BODY
NOTE:
Before cleaning the camera, remove the battery and/or disconnect power plug from the outlet.
Also, remove the SD Memory card and lens unit.
11.1.1.1. DUST/DIRT ON THE OUTER CASING PART (S)

1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up fingerprint and/or dirt on the Outer casing part with the dry fuzz-free cloth.
11.1.1.2. DUST/DIRT ON THE IMAGE SENSOR

1. Blow off the dust on the surface of the Image sensor with the Blower. (Refer to the following Figure.)
Keep the Mount Facing down condition towards to floor when cleaning.
Do not put the Blower further inside than the lens mount.
Be careful not to blow too strongly.
2. Wipe off the dirt on the image sensor surface with Lens cleaning KIT(BK)(VFK1900BK).
11.1.1.3. ABOUT THE LVF UNIT

[PROCEDURES]
1. By referring the Disassembly & Assembly procedures and remove the LVF unit.
2. Disassemble the LVF unit as follows, then blow off the dust with blower.
3. Wipe off the dirt on the surface of glasses with Lens Cleanig KIT (VFK1900BK), if necessary.
47
11.1.2.
ABOUT THE LENS
11.1.2.1. DUST/DIRT ON THE OUTER CASING PART(S)

1. Blow off the dust first, then sweep out the dust from narrower spaces with soft cleaning brush.
2. Wipe up the Outer casing part with the dry fuzz-free cloth.
11.1.2.2. DUST/DIRT ON THE LENS GLASSES

Define the location of the dust/dirt first, whether it is outside
lens surface or not.
1. When it is outside surface of the lens:
When the dust and/or dirt gets on the outer side surface of the Lens glasses, order the following procedures.
a. Blow off the dust on the Lens glass surface with
the Blower, gently. (Do not Blow too strongly.)
b. Wipe out the dirt on the lens glass surface with
Lens cleaning KIT(BK) (VFK1900BK) if necessary.
(Consult the Instruction sheet which is included in
the Lens cleaning KIT(BK) in details.)
2. When it is inside of the lens:
Refer to the 11.2. General description (Lens cleaning: Interchangeable Lens/H-FS014042),
11.3.
General description (Lens cleaning: Interchangeable
Lens/H-FS045200) section of this service manual.
11.2. General description (Lens cleaning: Interchangeable Lens/H-FS014042)

When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
48
11.2.1.
Disassembly procedure
11.2.1.3. Removal of a dust /dirt
Important:
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
1. Blow off the dust on the surface of the lens with a blower
brush.
2. Use lens cleaning KIT(BK) (VFK1900BK), if necessary.
11.2.1.1. Removal of the Decoration Ring

1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
and lens glass), and peel off the decoration ring gently.
11.2.1.2. Removal of the 1st Lens Frame

Unit
1. Remove the 3 screws (A).
49
11.2.2.
Assembly procedure
11.2.2.2. Installation of the Decoration Ring
Important:
When tightening the screw, use a torque driver (RFKZ0456)
by ordering the screwing order with specified torque
described in each step.
1. Use the Name Ring fixture (RFKZ0507)

2. Use new Decoration ring. (Do not use the one which is
removed.)
11.2.2.1. Installation of the 1st lens frame

unit
1. Tighten the 3 screws (A) with specified torque in numerical order.
(Torque Driver: RFKZ0456)
(Torque: 10 1.0 N-cm)
50
11.3. General description (Lens cleaning: Interchangeable Lens/H-FS045200)

When there is a dust/dirt inside surface of the 1st lens frame unit and/or subject side surface of the 2nd lens frame unit, remove it by
referring the following procedures.
Important:
1. When removing the 1st lens frame unit, it has to be proceed inside of satisfied clean level.
(Less than class 10,000 (Federal Standard 209D))
As for clean box, refer to the "8.2. Clean Box", in details.
2. When tighten the screws (A), use torque driver (RFKZ0456) with specified torque.
3. To keep the Lens performance, use only the 1st lens frame unit which was fitted as it was.
Therefore, the 1st lens frame unit is not supplied as spare parts.
Also do not exchange the 1st lens unit taking from others.
51
11.3.1.
Disassembly procedure
11.3.1.2. Removal of the 1st Lens Frame

Unit
Important:
It must be performed inside of satisfied clean level.
(Satisfied clean level: Less than class 10,000 (Federal
Standard 209D))
1. Remove the 3 screws (A).
11.3.1.1. Removal of the Decoration Ring

1. Decoration ring is sticked on the 1st lens frame unit.
2. Put the sheet so that the lens glass is fully covered.
3. Insert the needle to Gap (A) (between the decoration ring
and lens glass), and peel off the decoration ring gently.
11.3.1.3. Removal of a dust /dirt

1. Blow off the dust on the surface of the lens with a blower
brush.
2. Use lens cleaning KIT(BK) (VFK1900BK), if necessary.
52
11.3.2.
Assembly procedure
2. Tighten the 3 screws (A) with specified torque in numerical order.

(Torque Driver: RFKZ0456)
(Torque: 14.7 1.0 N-cm)
Important:
When tightening the screw, use a torque driver (RFKZ0456)
by ordering the screwing order with specified torque
described in each step.
11.3.2.1. Installation of the 1st lens frame

unit
1. Install the 1st lens frame unit onto the lens unit to meet
the through hole (A) with projection (A).
53
11.3.2.2. Installation of the Decoration Ring

1. Use the Name Ring fixture (RFKZ0507)
2. Use new Decoration ring. (Do not use the one which is
removed.)
54
DSC1106032CE
Service Manual
S1.1. Important Safety Notice
Diagrams and Replacement

Parts List
Digital Camera/Lens Kit/
Double Zoom Lens Kit/Body
Model No.
DMC-G3KPP
DMC-G3KPC
DMC-G3KEB
DMC-G3KEC
DMC-G3KEE
DMC-G3KEG
DMC-G3KGC
DMC-G3KGD
DMC-G3KGH
DMC-G3KGK
DMC-G3KGN
DMC-G3KGT
DMC-G3PP
DMC-G3PC
DMC-G3EB
DMC-G3EC
Vol. 1
Colour
[DMC-G3K]
(K)........Black Type
(R)...........Red Type (except GD/GT)
(W)..........White Type (except PC/EG)
(T)...........Brown Type (only PP/EG/GC)
COMPONENTS IDENTIFIED WITH THE MARK

HAVE THE SPECIAL CHARACTERISTICS
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as " " mark.
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
DMC-G3EE
DMC-G3EG
DMC-G3GC
DMC-G3GD
DMC-G3GH
DMC-G3GN
DMC-G3GT
DMC-G3WPP
DMC-G3WEB
[DMC-G3]
S1. About Indication of The Schematic Diagram
DMC-G3WEC
DMC-G3WEE
DMC-G3WEG
DMC-G3WGC
DMC-G3WGD
DMC-G3WGH
DMC-G3WGK
DMC-G3WGN
DMC-G3WGT
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
Circuit name being connected.
[DMC-G3W]
(R)...........Red Type (except PP/EE/GD/GT)
(W)..........White Type (except PP/EB/EE/EG)
(T)...........Brown Type (only EG/GC)
(KA).........Black Type (only EB)
OFTR
DMC-G3K series: Interchangeable Lens (H-FS014042) is bundled.

DMC-G3W series: Interchangeable Lens (H-FS014042/H-FS045200) are bundled.
DMC-G3 series: Camera Body Only.
FEP
Name of Signal
Table of contents
S1. About Indication of The Schematic Diagram............................. S-1

S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart............................................................................ S-2
S2.1. Flash P.C.B............................................................................ S-2
S3. Block Diagram........................................................................... S-3
S3.1. Overall Block Diagram........................................................... S-3
S4. Schematic Diagram................................................................... S-4
S4.1. Interconnection Diagram........................................................ S-4
S4.2. Top Operation Schematic Diagram........................................ S-5
S4.3. Flash Schematic Diagram...................................................... S-6
S4.4. Rear Operation Schematic Diagram...................................... S-7
S4.5. MIC Schematic Diagram........................................................ S-8
S5.4. MIC P.C.B............................................................................. S-12

S6. Replacement Parts List........................................................... S-13
S7. Exploded View........................................................................ S-22
S7.1. Frame and Casing Section.................................................. S-22
S7.2. Camera Lens Section (1)..................................................... S-23
S7.3. Camera Lens Section (2)..................................................... S-24
S7.4. Packing Parts and Accessories Section (1)......................... S-25
S5. Print Circuit Board..................................................................... S-9

S5.1. Top P.C.B............................................................................... S-9
S5.2. Flash P.C.B.......................................................................... S-10
S5.3. Rear Operation P.C.B........................................................... S-11
S-1
This signal is connected

to the FEP schematic diagram.
S2. Voltage Chart

Note) Indicated voltage values are the standard values for the unit measured by the DC electronic circuit tester (high-impedance) with the chassis taken as standard.
Therefore, there may exist some errors in the voltage values, depending on the internal impedance of the DC circuit tester.
S2.1. Flash P.C.B.

REF No.
Q8502
Q8502
Q8502
Q8502
Q8502
Q8502
QR8501
QR8501
QR8501
QR8501
QR8501
QR8501
QR8502
QR8502
QR8502
PIN No.
1
2
3
4
5
6
1
2
3
4
5
6
E
C
B
POWER ON
7.8
7.8
0
0
7.8
7.8
0
4.5
0
4.8
4.5
0
0
4.5
0
S-2
S3. Block Diagram

S3.1. Overall Block Diagram
MOUNT BOX UNIT

MOS SENSOR
16M
LENS UNIT
SD
CARD
IC3101
ANALOG
FRONTEND
REMOTE
TERMINAL
LENS CONTACT
TERMINAL
SSWF
IC9101
SYSTEM IC
SHUTTER
UNIT
IC9102,Q9193
Q4001,4002
MIC AMP
MICROPHONE AMP
VIDEO OUT
MICROPHOME
(STEREO)
IC9901
MOTOR DRIVE
AV OUT / DIGITAL
TERMINAL
IC9001
IC9003
IC9801
Q9801, T9801
EXT. FLASH
(OPTION)
IC6101
BUS SWITCH
HOT SHOE
UNIT
FLASH
HDMI
TERMINAL
IC6001
VENUS FHD
Q8001,8002
QR6001-6003
QR8001-8002
CAMERA PROCESS
J-PEG COMP/EX PANDS
MEDIA I/F
USB I/F
MAIN MICROPROCESSOR
OIS CONTROL
LENS DRIVE
LCD DRIVE
DDR MOBILE RAM1 /1G-bit
DDR MOBILE RAM1 /1G-bit
NOR FLASH MEMORY/128M-bit
HDMI DRIVER
Q8501,8502
QR6003,8501
QR8502
IC7201
TOUCH PANEL
DRIVER
TOUCH PANEL
COLOR LCD
PANEL
3.0" PANEL
460k dots
REAR OPERATION UNIT
IC9104, 9106
REGULATOR
X9101
(32.768kHz)
IC9002
LVF POWER CONT.
COLOR LVF
0.46" PANEL
1440k dots
IC9101
SYSTEM IC
X6001
(24MHz)
TOP OPERATION UNIT
IC1021, 1511, 2011-3013,

IC3021, 3022, 3031, 3041,
IC3051
REGULATOR
IC1001
POWER
BATTERY
(POWER SUPPLY)
HOT SHOE
DMC-G3 OVERALL BLOCK DIAGRAM
S-3
39
GND
37
BL+
35
GND
33 S TPANEL CS
31 S TPANEL SI
29
GND
27
LCD SCK
25
LCDOUT0
23
LCDOUT2
21
LCDOUT4
19
LCDOUT6
17
LCDOUT8
15
LCDOUT10
13
LCDOUT12
11
LCDOUT14
9
LCD CLK
7
LCDVD
5
D3V
3
D1R8V
1
GND
4
FP7205
3
1
2
3
4
1
FP
7
BL 204
BL PLU
MI
NU S
NC S
NC
XP
YN
XN
YP
FP7202
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
VGL
C4P
C3P
SCEN
SDA
DR6
DR4
DR2
DR0
DG6
DG4
DG2
DG0
HSYNC
VDDL
VSS1
VCOML
VCIM
CXP
VCIX2
C2N
C1N
VS
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
42
44
C4N
C3N
VGH
SCL
DR7
DR5
DR3
DR1
DG7
DG5
DG3
DG1
DCLK
VSYNC
VDDIO1
VGM
VCOMH
CXN
VCI
VSS2
C2P
C1P
TOUCH PANEL
FLASH
UNIT
(SSWF)
MOUNT BOX UNIT

(LENS CONTACT)
1
2
1
2
LCD UNIT
LCD IF P.C.B.
(FOIL SIDE)
S-4
P8503
LUMPLUMP+
P8502
TRG IN
UNREG GND
FP9009
UNREG
2
UNREG
4
UNREG
6
NC
8
INT STB TRG 10
UNREG GND 12
UNREG GND 14
UNREG GND 16
STB CHG LV 18
PW D4R8V
UNREG
UNREG
UNREG
GND
STB PWM OUT
UNREG GND
UNREG GND
UNREG GND
PW D4R8V
RS2 D
5SKIP D
HST D
VDRRS D
DVDD D
SWA D
RSD D L
GND
CLDCNC D L
PWB D L
VDDCEL D L
SLIMIT2 D L
MPXLOW D L
LGCEL D L
DP D L
SRRST L
V1 L
EV1 L
DVDD1 L
MPXPOW L
SHT L
DVDD L
FLASH P.C.B.
(FOIL SIDE)
4
3
2
1
P8001
BAT +
BAT THERMO
BAT DET
BAT -
POWER FPC
MAICO FPC
SSWF FPC
LENS FPC
LENS UNIT
TOP OP FPC
MIC 4R5V
MIC GND
MIC RIN
MIC LIN
MIC GND
MIC TR BIAS
INT DET SW
D GND
REAR DIAL
UNIT
8
7
6
5
4
3
2
1
TOP P.C.B.
(COMPONENT SIDE)
FP9003
1
GND
2
GND
3
GND
4
GND
5
GND
6
VDD
7
VDD
8
VDD
9
DATA0
10
DATA1
11
DATA2
12
DATA3
13
DATA4
14
DATA5
15
DATA6
16
DATA7
17
DATA8
18
DATA9
19
DATA10
20
DATA11
21
DATA12
22
DATA13
23
DATA14
24
DATA15
25
GND
26
GND
27 VIO VIDEO(D1R8V)
28
GND
29
GND
30
GND
31
GND
32
CLOCK
33
VALID
34
HSYNC
35
VSYNC
36 VIO SERIAL(D3V)
37
SCLK
38
SEN
39
NC
40
SDAT
41
RESET
42 VCC(3V-SW)
43 VCC(3V-SW)
44
GND
45
GND
1
3
5
7
9
11
13
15
17
19
21
23
LEN4R2V
LEN4R2V
LEN4R2V
LEN4R2V
GND
GND
GND
GND
LSRST
LSL2B
LSCK
LSLDP
2
4
6
8
10
12
14
16
18
20
22
4
3
2
1
MAIN P.C.B.
(FOIL SIDE)
6
GND
5 REAR KEYIN2
4 REAR KEYIN1
3 CROSS KEY IN
2
NC
1
GND
4
3
2
1
BATTERY
FP9010
15
MIC 4R5V
14
MIC 4R5V
13
MIC GND
12
MIC R IN
11
MIC L IN
10
MIC GND
9 MIC TR BIAS
8 INT DET SW
7
D GND
6
D GND
5 POWER ON L
4
D GND
MODE DIAL
2 LED PWR OUT 3
1
PW D3R0
FP9005
19 TOP KEYIN
18 CMD DIAL1
17 CMD DIAL0
16 SHUTTER HALF
15 SHUTTER FULL
14 LED IA VCC
13 LED IA OUT
12 UNREG GND
11 UNREG GND
10 UNREG GND
9 UNREG GND
8 UNREG GND
7
BAT DET
6 BAT THERMO
5
UNREG
4
UNREG
3
UNREG
2
UNREG
1
UNREG
FP9002
UNREG GND
UNREG GND
SSWF OUT
SSWF OUT
VSRC R
TRAN R
LGCELEXT R
CCL U R
GND
GND
ICNTCOL R
PWB U R
GND
AVDD U
GND
GND
GND
GND
CGCH1 U
VMIX2
OUTAMPCL U
GND
GND
RS1 U
5SKIPS U
NCSH U
NCCL U
SWB U
2MIX
GND
GND
PWB U L
ICNTCOL L
LOADCELL U
GND
CCL U L
LGCELEXT L
GND
TRAN L
VSRC L
FP8002
CMD DIAL1
REG GND
PON ON L
CMD DIAL0
6
GND
5
NC
4 CROSS KEY IN
3 REAR KEYIN1
2 REAR KEYIN2
1
GND
(SHUTTER)
1
3
5
7
9
11
13
15
17
19
FP3913
1
GND
2
3
RS1 D
4
5
5SKIPS D
6
7
NCSH D
8
9
NCCL D
10
11
SWB D
12
13
3MIX D
14
15
GND
16
17
GND
18
19
GND
20
21
PWB D L
22
23 SLIMIT1 D L
24
25 LOADCELL D
26
27
GND
28
29
CCL D L
30
31
SFRST
32
33
RDCEL L
34
35
V2 L
36
37
EV2 L
38
39
ALLRS L
40
41
VST L
42
43
RSCEL L
44
45
GND
FP3911
71
69
67
65
63
61
59
57
55
53
51
49
47
45
43
41
39
37
35
33
31
29
27
25
23
21
19
17
15
13
11
9
7
5
3
1
23 TOP KEY IN
21
CMD DIAL0
19 SHUTTER FULL
17 LED IA OUT
15 UNREG GND
13 UNREG GND
11 UNREG GND
9
BAT DET
7
UNREG
5
UNREG
3
UNREG
1
UNREG
FP8001
22 CMD DIAL1
20 SHUTTER HALF
18 LED IA VCC
16 UNREG GND
14 UNREG GND
12 UNREG GND
10 UNREG GND
8 BAT THERMO
6
UNREG
4
UNREG
2
UNREG
HOT SHOE FPC
70
ERSCEL R
68
ETRAN R
66
DP U R
64
LGCEL U R
62 MPXLOW U R
60 SFIUPCNT R
58 VDDCEL U R
56
PWB U R
54 CLDCNC U R
52
AVDD U
50 AOUTB U(GB)
48 AOUTA U(B)
46
LGAMP U
44
RSD U R
42
CGCH2 U
40
VMIX1
38
HCK U
36
SIGRS U
34
RS2 U
32
5SKIP U
30
HST U
28
VDRRS U
26
DVDD U
24
SWA U
22
RSD U L
20 CLDCNC U L
18
PWB U L
16 VDDCEL U L
14 SFIUPCNT L
12 MPXLOW U L
10
LGCEL U L
8
DP U L
6
FDUP
4
ETRAN L
2
ERSCEL L
GND
GND
LED AF OUT
G SP POS
NC
STRXD
NC
NC
STX
SPEAKER
4
3
2
1
FP8501
10
PW D4R8V
9 STB CHG LV
8 UNREG GND
7 UNREG GND
6 STB PWM OUT
5 INT STB TRG
4 UNREG GND
3
NC
2
UNREG
1
UNREG
SHUTTER FPC
FP9007
19 LCD EVF SEL
17
GND
15 LED AF VCC
13
NC
11
G SP NEG
9
STRTTL
7
STTXD
5
NC
3
STX
1
STX
2
GND
4
GND
6
D1R8V
8
D3V
10
LCD VD
12
LCD CLK
14
LCDOUT14
16
LCDOUT12
18
LCDOUT10
20
LCDOUT8
22
LCDOUT6
24
LCDOUT4
26
LCDOUT2
28
LCDOUT0
30
LCD SCK
32
GND
34 S TPANEL SI
36 S TPANEL CS
38
GND
40
BL+
42
GND
44 LCD ROTATE1
FP9004
18
16
14
12
10
8
6
4
2
LCD ROTATE2
LCD OPEN H
GND
D3V
D3V
LCD HD
LCDOUT15
LCDOUT13
LCDOUT11
LCDOUT9
LCDOUT7
LCDOUT5
LCDOUT3
LCDOUT1
LCD SDOUT
LCD CS
TPANEL REQ
S TPANEL SO
S TPANEL SCK
BLGND
GND
GND
HINGE SW FPC
DVDD R
SHT R
MPXPOW R
DVDD R
EV1 R
V1 R
SRRST R
DP D R
LGCEL D R
SLIMIT2 D R
VDDCEL D R
PWB D R
CLDCNC D R
AVDD D
AOUTB D(R)
AOUTA D(GB)
LGAMP D
RSD D R
VREV
OB5SKIP
HCK D
SIGRS D
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
41
43
45
HOT SHOE
FP3912
1
GND
2
3
RSCEL R
4
5
VST R
6
7
ALLRS R
8
9
EV2 R
10
11
V2 R
12
13
RDCEL R
14
15 SFRST D R
16
17
CCL D R
18
19 MPXLOW D R
20
21 SLIMIT1 D R
22
23
PWB D R
24
25
GND
26
27
AVDD D
28
29
GND
30
31
GND
32
33
GND
34
35
GND
36
37 LDCELSTR
38
39 GASOSHCH
40
41 OUTAMPCL D
42
43
GND
44
45
GND
FP9006
1
MOT(1)
2
MOT(1)
3
MOT(1)
4
MOT(1)
5
MOT(2)
6
MOT(2)
7
MOT(2)
8
MOT(2)
9
2CMG
10 COM(MOT4R8V)
11 COM(MOT4R8V) 12
1CMG
13
LPSW
14 GND(LPSW)
15
BRUSH(1)
16
BRUSH(2)
17 BRUSH GND 18 BRUSH GND
19
BRUSH(3)
HINGE FPC
38
GND
36
BL34 S TPANEL SCK
32 S TPANEL SO
30 TPANEL REQ
28
LCD CS
26 LCD SDOUT
24
LCDOUT1
22
LCDOUT3
20
LCDOUT5
18
LCDOUT7
16
LCDOUT9
14
LCDOUT11
12
LCDOUT13
10
LCDOUT15
8
LCDHD
6
D3V
4
D3V
2
GND
S4. Schematic Diagram
S4.1. Interconnection Diagram

FP4202
FP4201
MIC GND
ECM RIN
ECM LIN
MIC GND
MIC FPC
MIC P.C.B.
(FOIL SIDE)
STEREO
MICROPHONE
FP9008
FP9001
LEN4R2V
LEN4R2V
LEN4R2V
GND
GND
GND
GND
LSDET
LSB2L
LSDIO
LSB2A
FP7203
REAR FPC
MAIN STB FPC

LVF UNIT
REAR OP P.C.B.
(COMPONENT SIDE)
FP7550
DMC-G3 INTERCONNECTION DIAGRAM
S4.2. Top Operation Schematic Diagram
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE 2.5A 32V FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES
D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MME TYPE 2.5A 32V.
2.5A 32V
Until
FP8001 K1MY23BA0235
BackLock/BottomContact
Molex/502350-2300
2.5A 32V
$[F1J1A106A024]
[22] C8001
G1
UNREG
UNREG
UNREG
BAT_THERMO
BAT_DET
UNREG_GND
10
UNREG_GND
11
UNREG_GND
12
UNREG_GND
13
UNREG_GND
14
UNREG_GND
15
UNREG_GND
16
LED_IA_OUT
17
LED_IA_VCC
18
SHUTTER_FULL
19
SHUTTER_HALF
20
CMD_DIAL0
21
CMD_DIAL1
22
TOP_KEY_IN
23
UNREG_GND
0[18]
R8001
BAT_+
BAT_THERMO
BAT_DET
BAT_-
CC8002
ON_BOARD_CONTACT
IPS-4077T-01Y900
K4AC01D00001
ET8001
BAT_THERMO
BAT_DET
D8001
B3AEB0000141
LED_IA_OUT
IA_LED(BLUE)
S8001
K0F111A00591
LED_IA_VCC
SHUTTER_FULL
SHUTTER_HALF
CMD_DIAL0
CMD_DIAL1
TOP_KEY_IN
VA8006
UNREG
$[D4ED18R0A014]
UNREG
UNREG_CN
P8001
K4ZZ04000057
$[D4ED18R0A014]
CC8001
VA8005
UNREG
Fuse Number:O
F8001
ERBSE2R50U
LB8001
J0JGC0000038
S8002
K0F212A00006
1
S1
VA8002
$[D4ED18R0A014]
UNREG
Confidential
3
S2
6
IA
G2
FP8002 K1MY04BA0370
Molex/503480-0400
BackLock/BottomContact
C
10k
G2
4 CMD_DIAL1
R8004
3 REG_GND
$[D4ED18R0A014]
VA8004
$[D4ED18R0A014]
VA8003
$[D4ED18R0A014]
VA8001
2 PON_ON_L
1 CMD_DIAL0
G1
A
DMC-G3/G3K/G3W
Top Operation
Schematic Diagram
S-5
10
S4.3. Flash Schematic Diagram
1.5A 32V
CAUTION: FOR CONTINUED PROTECTION AGAINST FIRE HAZARD,

REPLACE ONLY WITH THE SAME TYPE 1.5A 32V FUSE.
ATTENTION: POUR UNE PROTECTION CONTINUE LES RISQUES
D' INCENDIE N' UTILISERQUE DES FUSIBLE DE MME TYPE 1.5A 32V.
To MAIN PCB
1.5A 32V
CL8501
D8502
B0HCMP000006
LUMP-
D8501
G1
R8506
910K[D][22]
C8510
F2A2F1710001
R8508
300K[D]
[22]
630V
315V
[36]
Q8501
B1JBLP000022
OR
UNREG_GND
TRG_IN
[36]
630V
R8514
4.7K[36]
G1
NC
UNREG_GND
UNREG_GND
STB_CHG_LV
10 PW_D4R8V
R8511
15K
F1K2J333A029
C8501
R8503
100K
G2
UNREG
22
3
D
R8509
16K[D]
R8501
100K[36]
CL8505
R8513
B1DFCG000020
RL8503
RL8501
UNREG
Q8502
C8504
F1K2J102A028
UNREG_GND
5 INT_STB_TRG
6 STB_PWM_OUT
B0ECGP000006
1
FP8501
K1MN10BA0108
4
C8507
F1J1A106A023
R8507
910K[D][22]
[FPSN4TP]
[C65-KT3L(MITSUMI)]
10V
LUMP+
G5D1A0000074
R8512
1M[36]
250V
G2
T8501
C8502 [36]
F1K2E2230002
CL8502
F8501
ERBSE1R50U
D8503
DA2JF8100L
P8503
K1KA02B00292
(SM02B-SFHRS-TF(LF)(SN))
(RED)
(51281-1040/molex)
CL8503
P8502
K1KA02ZA0001
(SM02B-SSR-H-ETB(LF)(SN))
R8504
22[18]
R8510
1K
CL8504
QR8502
6
B1GBCFGJ0021
10V
1
R8505
100[18]
QR8501
C8506
1u[18]
B1GKCFJN0008
A
DMC-G3/G3K/G3W
Flash
Schematic Diagram
S-6
10
S4.4. Rear Operation Schematic Diagram
10K
SET
R7551
DISP
1
R7550
$
TO MAIN-PCB
FP7550
K1MN06BA0272
06FKZ-SM1-GAN-1-ETB(LF)(SN) / JST
ZIF-TYPE/ TOP contact
F
S7551
K0F111A00595
S7550
K0F111A00591
R7553
REC
R7552
$
G2
6 GND
5 NC
4 CROSS_KEY_IN
3 REAR_KEYIN1
R7554
REC
3.9K
PLAY
2.4K
PLAY
2 REAR_KEYIN2
1 GND
QMENU
3
G1
RIGHT
LEFT
DOWN
R7555
$
R7556
R7557
UP
R7559
2
3.9K
7.5K
S7552
K0F111A00595
2.4K
DISP/Fn1
REC
DISP/Fn1
UP
PLAY
MENU/SET
RIGHT
UP
DOWN
RIGHT
MENU/SET
LEFT
S7557
K0F111A00595
S7556
K0F111A00595
S7555
K0F111A00595
S7554
K0F111A00595
S7553
K0F111A00595
LEFT
DOWN
QMENU/Fn2/DEL
(View)
QMENU/Fn2/DEL
S7558
K0F111A00595
4
1
GND
Confidential
Until
A
DMC-G3/G3K/G3W
Rear Operation
Schematic Diagram
S-7
10
S4.5. MIC Schematic Diagram
VA4203
$[D4ED18R00004]
(SPVN310100(ALPS))
Normaly-Open_SW
K0L1BA000159
S4201
POP UP DET SW
R4205
1k
R4206
1u
1k
C4206
[560p]
F1G0J1050007
10V
C42056.3V
$[F1G1H5610004]
B1ABDF000017
Q4202
R4207
100K[18]
ERA3YKD104V
F1G1A1040006
C4208 0.1u
SHIELD by MIC_GND
$[F1G1H5610004]
1k
F1G0J1050007
G1
10V
R4203
6.3V
C4204
[560p]
G2
B1ABDF000017
Q4201
C4203
K1MY08BA0370
FP4202
0.5mmPitch
Backflip Top_Contact
FPC CONTACT to TOP_OP_FPC
F1G1A1040006
C4207 0.1u
ERA3YED392V
R4202
3.9k[18]
R4204
100K[18]
ERA3YKD104V
1u
C4202
$[F1G1H330A565]
3
C4201
$[F1G1H330A565]
ECM_RIN
VA4202
MIC_GND
R4201
3.9k[18]
ECM_LIN
$[D4ED18R00004]
G1
MIC_GND
VA4201
$[D4ED18R00004]
ERA3YED392V
Connect emitter to collector shortest

0.5mmPitch
Backflip Top_Contact
FPC CONTACT to MIC_FPC
K1MY04BA0370
FP4201
D_GND
INT_DET_SW
MIC_TR_BIAS
4
5
MIC_GND
MIC_LIN
MIC_RIN
MIC_GND
MIC_4R5V
G2
SHIELD by MIC_GND
Connect emitter to collector shortest
R4208
1k
B
Confidential
Until
A
DMC-G3/G3K/G3W
MIC
Schematic Diagram
S-8
10
S5. Print Circuit Board

S5.1. Top P.C.B.
FP8002
1234
ET8001
15
23
FP8001
LB8001
VA8001
VA8004
20 22
R8004
10
VA8003
F8001
P8001
E
4
(Component Side)
D
D8001
VA8002
2
S8001
VA8005
VA8006
C8001
S8002
R8001
CC8002
CC8001
(Foil Side)
A
DMC-G3/G3K/G3W
Top P.C.B.
S-9
10
S5.2. Flash P.C.B.
P8502
P8503
2
C8502
R8514
D8501
CL8502
R8501
C8501
R8512
654
2
Q8502
R8513
T8501
Q8501
CL8501
R8511
123
CL8505
D
R8503
D8502
D8503
C8507
R8504
R8505
C8504
R8506
C8506
R8507
10
1 2 3
QR8501
FP8501
R8508
R8510
6 5 4
CL8503
QR8502
R8509
CL8504
F8501
B
RL8501
RL8503
C8510
(Component Side)
1
DMC-G3/G3K/G3W
Flash P.C.B.
(Foil Side)
4
S-10
10
S5.3. Rear Operation P.C.B.
4
2
S7550
4
2
3
S7551
R7556
R7557
R7555
R7552
4
2
FP7550
R7553
65
R7550
R7554
S7557
R7559
S7552
(Component Side)
S7558
S7555
4
2
S7553
3
3
S7556
S7554
R7551
(Foil Side)
DMC-G3/G3K/G3W
Rear Operation P.C.B.
S-11
10
S5.4. MIC P.C.B.
4
S4201
VA4203
FP4202
R4208
C4208
R4207
R4204
FP4201
1234
C4202
VA4202
C4204
R4201
R4203
C4201
C4203
VA4201
C4205
R4202
R4206
Q4202
C4206
C4207
Q4201
R4205
(Component Side)
(Foil Side)
A
DMC-G3/G3K/G3W
MIC P.C.B.
S-12
10
S6. Replacement Parts List
E.S.D. standards for Electrostatically Sensitive Devices, refer to PREVENTION OF

ELECTROSTATIC DISCHARGE (ESD) TO ELECTROSTATICALLY SENSITIVE (ES) DEVICES
section.
<ABOUT LENS MAIN BLOCK UNIT "(Ref.208 and Ref.308)>
1. In case of the "LENS MAIN BLOCK UNIT" (Ref.208 and Ref.308) defects, contact to
the service department of sales company.
<DEFINITION OF PARTS SUPPLIER>
1. Parts marked with [ENERGY] in the remarks column are supplied from Panasonic Corporation
Energy Company.
2. Parts marked with [SPC] in the remarks column are supplied from AVC-CSC-SPC.
Others are supplied from PAVCSG.
S-13
DMC-G3EG-K vol.1
Ref.No.
Part No.
Part Name & Description
Pcs
##
VEP56135A
MAIN P.C.B.
##
VEP56135B
MAIN P.C.B.
## VEP56137A
## VEP56136A
## VEP50086A
## VEP54024A
## VEP59096A
TOP P.C.B.
FLASH P.C.B.
REAR OPERATION P.C.B.
MIC P.C.B.
LCD IF P.C.B.
1
1
1
1
1
## VEP56137A
TOP P.C.B.
Remarks
(RTL) E.S.D.
PP,PC,EE,GC,GH,GT,GN,GD,
KPP,KPC,KEE,KGC,KGH,KGT,
KGK,KGN,KGD,WPP,WEE,WGC,
WGH,WGT,WGK,WGN,WGD
(RTL) E.S.D. EG,EC,EB,
KEG,KEC,KEB,WEG,WEC,WEB
(RTL) E.S.D.
(RTL) E.S.D.
(RTL)
(RTL) E.S.D.
(RTL) E.S.D.
(RTL) E.S.D.
D8001 B3AEB0000141 LED
1 E.S.D.
ET8001 K4AC01D00001 EARTH SPRING
F8001 ERBSE2R50U
FUSE 32V 2.5A
FP8001 K1MY23BA0235 CONNECTOR

LB8001 J0JGC0000038
FILTER
P8001 K4ZZ04000057
CONNECTOR
1
23P
4P
1
1
Ref.No.
Part No.
T8501 G5D1A0000074 TRANSFORMER
## VEP50086A
4P
S8001 K0F111A00591
S8002 K0F212A00006
1
1
SWITCH
SWITCH
FLASH P.C.B.
C.CAPACITOR 630V 0.033U
C.CAPACITOR 250V 0.022U
C.CAPACITOR 630V 1000P
C.CAPACITOR CH 10V 1U
C.CAPACITOR CH 10V 10U
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
1
1
1
1
1
1
S7550
S7551
S7552
S7553
S7554
S7555
S7556
S7557
S7558
K0F111A00595
K0F111A00595
K0F111A00595
K0F111A00595
K0F111A00595
K0F111A00595
K0F111A00595
K0F111A00595
K0F111A00595
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
SWITCH
1
1
1
1
1
1
1
1
1
MIC P.C.B.
F1G0J1050007
F1G0J1050007
F1G1A1040006
F1G1A1040006
1 E.S.D.
1 E.S.D.
1 E.S.D.
FUSE 32V 1.5A

10P
P8502 K1KA02ZA0001 CONNECTOR

P8503 K1KA02B00292 CONNECTOR
2P
2P
1
1
Q8501 B1JBLP000022 TRANSISTOR

Q8502 B1DFCG000020 TRANSISTOR
1 E.S.D.
1 E.S.D.
QR8501 B1GKCFJN0008 TRANSISTOR-RESISTOR

QR8502 B1GBCFGJ0021 TRANSISTOR-RESISTOR
1 E.S.D.
1 E.S.D.
100K
300K
16K
1M
4.7K
1U
1U
0.1U
0.1U
4P
8P
Q4201 B1ABDF000017 TRANSISTOR

Q4202 B1ABDF000017 TRANSISTOR
R4201
R4202
R4203
R4204
R4205
R4206
R4207
R4208
M.RESISTOR CH 1/4W
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
CHIP RESISTOR
M.RESISTOR CH 1/16W
M.RESISTOR CH 1/16W
CHIP RESISTOR
CHIP RESISTOR
M.RESISTOR CH 1/4W
CHIP RESISTOR
M.RESISTOR CH 1/4W
(RTL) E.S.D.
C.CAPACITOR CH 6.3V
C.CAPACITOR CH 6.3V
C.CAPACITOR CH 10V
C.CAPACITOR CH 10V

1
1
1
1
1
FP8501 K1MN10BA0108 CONNECTOR
ERJ8GEYJ104V
D0GA104JA023
D0GB220JA065
D0GB101JA065
ERJ6RED914V
ERJ6RED914V
ERJ2RKD304X
ERJ2RHD163X
D0GA102JA023
D0GA153JA023
ERJ8GEYJ105V
D0GA220JA023
ERJ8GEYJ472V
D0GA103JA023
D0GA242JA023
D0GA392JA023
D0GA242JA023
D0GA392JA023
D0GA752JA023
ERA3YED392V
ERA3YED392V
D0GA102JA023
ERA3YKD104V
D0GA102JA023
D0GA102JA023
ERA3YKD104V
D0GA102JA023
M.RESISTOR 1/16W
M.RESISTOR 1/16W
CHIP RESISTOR
M.RESISTOR 1/16W
CHIP RESISTOR
CHIP RESISTOR
M.RESISTOR 1/16W
CHIP RESISTOR
S4201 K0L1BA000159 SWITCH
R8501
R8503
R8504
R8505
R8506
R8507
R8508
R8509
R8510
R8511
R8512
R8513
R8514
6P
(RTL)
R7551
R7553
R7554
R7556
R7557
R7559
C4203
C4205
C4207
C4208
(RTL) E.S.D.
D8501 B0ECGP000006 DIODE

D8502 B0HCMP000006 DIODE
D8503 DA2JF8100L
DIODE
F8501 ERBSE1R50U
1
1
1
F1K2J333A029
F1K2E2230002
F1K2J102A028
F1H1A105A025
F1J1A106A043
Remarks
R8001 D0GBR00J0004 CHIP RESISTOR

R8004 D0GA103JA023 CHIP RESISTOR
C8501
C8502
C8504
C8506
C8507
Pcs
FP7550 K1MN06BA0272 CONNECTOR
## VEP54024A
## VEP56136A
1
1
1
1
1
1
1
1
1
1
1
1
1
S-14
1
1
1
1
1
1
1 E.S.D.
1 E.S.D.
3.9K
3.9K
100K
100K
1
1
1
1
1
1
1
1
1
DMC-G3EG-K vol.1
Ref.No.
Part No.
VEP56135B
MAIN P.C.B.
VEP56135A
MAIN P.C.B.
2
3
3
4
4
5
6
7
8
9
10
11
12
12
13
14
15
16
17
17
17
17
17-1
17-1
17-1
17-1
17-2
17-2
17-3
17-4
17-4
17-5
17-6
17-7
17-8
17-9
18
21
21
21
21
22
22
22
22
23
24
25
26
27
27
28
29
30
30
31
31
32
33
33
34
35
36
37
38
39
39
39
39
ML-421S/DN
VGK3763
VGK3764
VGK3765
VGK3766
VGQ0V34
VGQ0V35
VGQ0X52
VGQ0Y02
VGQ0Y02
VGQ0Y02
VGQ0Y03
VKF4888
VKF4889
VMT2182
VMT2183
VMT2184
VXQ2142T
VYK5B51
VYK5B54
VYK5B53
VYK5B52
VGK3760
VGK3788
VGK3787
VGK3770
VGK3792
VGK3793
VGQ0V87
VGU0J48
VGU0K13
VMB4504
VMP9970
VMP9995
VGQ0H89
VGQ0H89
VEK0R80
VKM9393
VKM9396
VKM9395
VKM9394
VKM9397
VKM9400
VKM9399
VKM9398
VMP0A03
VMP9961
VMP9998
VEP50086A
VGQ0V32
VGQ0V33
VGQ0V36
VGQ0W26
VGU0J50
VGU0K16
VGU0J51
VGU0K15
VGU0J53
VGU0K00
VGU0K14
VMB4373
VMP0A41
VMP9960
VMP9968
VWJ2268
VYK5B67
VYK5B70
VYK5B69
VYK5B68
BATTERY
SIDE ORNAMENT L
SIDE ORNAMENT L
SIDE ORNAMENT R
SIDE ORNAMENT R
EYE RUBBER
EYE CUP BASE
LENS FPC BUSTERAID
TAPE
TAPE
TAPE
TAPE
JACK DOOR
JACK DOOR
HEAT RADIATION PAD1
HEAT RADIATION PAD2
HEAT RADIATION PAD3
MOUNT BOX UNIT
FRONT CASE UNIT
FRONT CASE UNIT
FRONT CASE UNIT
FRONT CASE UNIT
GRIP PIECE FRONT
GRIP PIECE FRONT
GRIP PIECE FRONT
GRIP PIECE FRONT
MOUNT RING
MOUNT RING
FRONT BLIND PIECE
LENS RELEASE BUTTON
LENS RELEASE BUTTON
LENS RELEASE BUTTON SPRING
LENS RELEASE FIX PLATE
MOUNT RING PLATE
CUSHION
CUSHION
HINGE SW FPC UNIT
ARM COVER TOP
ARM COVER TOP
ARM COVER TOP
ARM COVER TOP
ARM COVER BOTTOM
ARM COVER BOTTOM
ARM COVER BOTTOM
ARM COVER BOTTOM
HINGE SW PLATE B
HINGE PLATE
HINGE SW PLATE A
GRIP PIECE REAR
GRIP PIECE REAR
LCD LOCK PIECE
LCD LOCK HOLDER
LVF/LCD BUTTON
LVF/LCD BUTTON
PLAYBACK/MOTION PICTURE BUTTON
PLAYBACK/MOTION PICTURE BUTTON
MOTION PICTURE PIECE
REAR OPERATION BUTTON
REAR OPERATION BUTTON
LCD LOCK SPRING
REC EARTH PLATE
REAR EARTH PLATE
REAR OPERATION EARTH PLATE
REAR OPEARTION FFC
REAR CASE UNIT
REAR CASE UNIT
REAR CASE UNIT
REAR CASE UNIT
Pcs
Remarks
Ref.No.
1 (RTL) E.S.D. EG,EC,EB,

KEG,KEC,KEB,WEG,WEC,WEB
1 (RTL) E.S.D.
PP,PC,EE,GC,GH,GT,GN,GD,
KPP,KPC,KEE,KGC,KGH,KGT,
KGK,KGN,KGD,WPP,WEE,WGC,
WGH,WGT,WGK,WGN,WGD
1 [ENERGY] (B9110)
1 (-K,-T,-R,-KA)
1 (-W)
1 (-K,-T,-R,-KA)
1 (-W)
1
1
1
1
1
1
1
1 (-K,-T,-R,-KA)
1 (-W)
1
1
1
1 [SPC]
1 (-K,-KA)
1 (-W)
1 (-T)
1 (-R)
1 (-K,-KA)
1 (-W)
1 (-T)
1 (-R)
1 (-K,-T,-R,-KA)
1 (-W)
1
1 (-K,-T,-R,-KA)
1 (-W)
1
1
1
1
1
1
1 (-K,-KA)
1 (-W)
1 (-T)
1 (-R)
1 (-K,-KA)
1 (-W)
1 (-T)
1 (-R)
1
1
1
1 (RTL)
1 (-K,-T,-R,-KA)
1 (-W)
1
1
1 (-K,-T,-R,-KA)
1 (-W)
1 (-K,-T,-R,-KA)
1 (-W)
1
1 (-K,-T,-R,-KA)
1 (-W)
1
1
1
1
1
1 (-K,-KA)
1 (-W)
1 (-T)
1 (-R)
S-15
40
41
42
43
44
44
44
44
45
45
45
45
45
46
50
50
50
50
56
57
57
59
60
61
62
63
64
65
66
67
68
68
69
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
88
88
88
89
89-1
90
91
92
93
93-1
94
B1
B1
B2
B2
B3
B3
B4
B4
B5
B5
B6
B6
B7
B8
Part No.
Pcs
VEP59096A
VGQ0V38
VGQ0Y08
VGQ0Y08
VKM9409
VKM9412
VKM9411
VKM9410
VKM9413
VKM9416
VKM9415
VKM9414
VKM9614
VYK5G82
VYK5B79
VYK5B82
VYK5B81
VYK5B80
VGQ0V89
VYK5B78
VYK5C72
VMC2111
K0RC00800003
VEK0R79
VEK0R81
VEP54024A
VEP56137A
VGQ0R32
VGQ0R33
VGQ0W43
VKM9421
VKM9422
VWJ2266
VGQ0R70
VGQ0W48
VGQ0W48
VGU0H25
VKM9388
VMB4304
VMB4500
VMB4509
VMP9955
VMP9956
VMP9957
VMP9958
VMS8177
F2A2F1710001
VEE1K29
VEP56136A
VMB4508
VYK5B91
VYK5B94
VYK5B93
VYK5B92
VYQ6831
VKM9429
L5EDDYY00255
VGQ0W20
VWJ2267
VWJ2271
VGQ0P70
VGQ0Y27
LCD IF P.C.B.
LCD BL BEZEL SHEET
LCD PCB SHEET
LCD PCB SHEET
LCD CASE TOP
LCD CASE TOP
LCD CASE TOP
LCD CASE TOP
LCD CASE BOTTOM
LCD CASE BOTTOM
LCD CASE BOTTOM
LCD CASE BOTTOM
LCD CASE BOTTOM
LCD UNIT
LCD HINGE UNIT
LCD HINGE UNIT
LCD HINGE UNIT
LCD HINGE UNIT
CAPACITOR PCB COVER
TOP CASE UNIT
TOP CASE UNIT
SHOE SPRING
MULTI-BUTTON SWITCH
MICROPHONE UNIT
FLASH UNIT
MIC P.C.B.
TOP P.C.B.
MIC CUSHION (B)
MIC CUSHION (C)
MIC CUSHION (A)
FLASH CASE TOP
FLASH CASE TOP
MAIN_POW_FPC
CAPACITOR TAPE
SHEET
SHEET
BATTERY LOCK KNOB
BATTERY FRAME
BATTERY LOCK SPRING
BATTERY DOOR SPRING
BATTERY OUT SPRING
BATTERY CASE
SIDE FRAME R
TRIPOD
HEAT RADIATION PLATE
BATTERY DOOR SHAFT
E.CAPACITOR
CAPACITOR GND HARNESS
FLASH P.C.B.
CAPACITOR EARTH SPRING
BATTERY DOOR UNIT
BATTERY DOOR UNIT
BATTERY DOOR UNIT
BATTERY DOOR UNIT
LVF UNIT
LVF COVER
LVF MODULE
LVF FPC FIX TAPE
MAIN FLASH FPC
LVF FPC
LVF FPC FIX TAPE
CUSHION
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
VHD2149
VHD2019
VHD2149
VHD2019
VHD2149
VHD2019
VHD2149
VHD2019
VHD2149
VHD2019
VHD2149
VHD2019
VHD2286
VHD2331-A
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Remarks
(RTL) E.S.D.
(-K,-KA)
(-W)
(-T)
(-R)
(-K)
(-W)
(-T)
(-R)
(-KA)
(-K,-KA)
(-W)
(-T)
(-R)
(-K,-T,-R,-KA)
(-W)
(RTL) E.S.D.
(RTL) E.S.D.
(-K,-T,-R,-KA)
(-W)
(C8510)
(RTL) E.S.D.
(-K,-KA)
(-W)
(-T)
(-R)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
DMC-G3EG-K vol.1
Ref.No.
B9
B10
B11
B12
B12
B13
B13
B14
B14
B15
B15
B16
B16
B17
B17
B18
B18
B19
B19
B20
B20
B21
B21
B22
B23
B24
B25
B26
B27
B30
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B44
B45
B45
B46
B46
B47
B47
B48
B49
B50
B51
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
B63
B64
Part No.
VHD2331-A
VHD2331-A
VHD2331-A
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD2337
VHD2338
VHD1909
VHD1909
XQN16+BJ4FN
XQN16+BJ4FN
XQN16+BJ4FN
XQN16+BJ4FN
VHD2332
VHD2332
VHD2332
VHD2332
VHD2091
VHD2091
VHD2190
VHD2190
VHD1998
XQN16+BJ4FN
XQN16+BJ4FN
XQN16+BJ4FN
XQN16+BJ4FN
XQN16+BJ4FN
VHD2179
VHD2200
VHD2179
VHD2200
VHD2333
VHD2102
VHD2333
VHD2102
VHD2335
VHD2335
XQN14+BJ4FJK
XQN14+BJ4FJK
XQN14+BJ4FJK
XQN14+BJ4FJK
XQN14+BJ4FJK
XQN14+BJ4FJK
XQN14+BJ4FJK
XQN14+BJ4FJK
VHD1996
VHD1996
VHD2019
VHD2286
XQN16+B3FN
XQN16+B3FN
XQN16+B3FN

SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
Pcs
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Remarks
Ref.No.
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
(-K,-T,-R,-KA)
(-W)
S-16
Part No.
Pcs
Remarks
DMC-G3EG-K vol.1
Ref.No.
Part No.
Pcs
Remarks
Ref.No.
200
200
202
203
204
206
207
VXW1261
VXW1267
VDW2023
VEJ2295
VGH5186
VDW2024
---
LENS UNIT
LENS UNIT
SHADING FRAME
MOUNT CONTACT UNIT
DECORATION RING
L MOUNT UNIT
REAR FRAME2 UNIT
1
1
1
1
1
1
1
207
---
REAR FRAME2 UNIT
208
---
LENS MAIN BLOCK UNIT
209
210
211
212
213
VMG1855
VMG1855
VMG1855
VMG1847
VGQ0Y87
FLOATING RUBBER
FLOATING RUBBER
FLOATING RUBBER
DUST PROOF RING
SILVER RING TAPE 1
1
1
1
1
1
(G3K,G3W)K,T,R,KA [SPC]
(G3K,G3W)W [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W)K,T,R,KA
(NOT SUPPLIED)
(G3K,G3W)W
(NOT SUPPLIED)
(G3K,G3W) [SPC]
See "Notes"
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
B201
B202
B203
B204
B205
B206
B207
B208
B209
B210
B211
B213
B220
B221
B222
XQN14+BJ4FNK
XQN14+BJ4FNK
XQN14+BJ4FNK
XQN14+BJ4FNK
XQN14+BJ4FNK
XQN14+BJ4FNK
XQN14+BJ4FNK
XQN2+AJ5FNK
XQN2+AJ5FNK
XQN2+AJ5FNK
XQN2+AJ5FNK
XQN14+AJ3FNK
XQN16+BJ5FNK
XQN16+BJ5FNK
XQN16+BJ5FNK
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
(G3K,G3W) [SPC]
S-17
Part No.
Pcs
Remarks
DMC-G3EG-K vol.1
Ref.No.
Part No.
Pcs
Remarks
300
300
302
303
304
305
306
307
VXW1264
VXW1270
P04F310
9630020
P0479H0
P04F900
P048H50
-----
LENS UNIT
LENS UNIT
DECORATION RING
SHADING FRAME
MOUNT CONTACT UNIT
ZOOM RUBBER RING
L MOUNT UNIT
REAR TUBE UNIT
1
1
1
1
1
1
1
1
307
-----
REAR TUBE UNIT
308
-----
LENS MAIN BLOCK UNIT
309
310
313
P04F370
P04F370
PB4F010
FLOATING RUBBER
FLOATING RUBBER
SILVER RING TAPE 2
1
1
1
(G3W) K,T,R,KA [SPC]

(G3W) W [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) K,T,R,KA
(NOT SUPPLIED)
(G3W) W
(NOT SUPPLIED)
(G3W) [SPC]
See "Notes"
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
B301
B302
B303
B304
B305
B306
B307
B308
B309
B310
B311
B312
B313
B317
B318
0HE4025
0HE4025
0HE4025
0242050
0242050
0242050
0242050
0B44035
9580270
0242070
0242070
0242070
0257030
0257030
0554012
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
SCREW
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
(G3W) [SPC]
Ref.No.
S-18
Part No.
Pcs
Remarks
DMC-G3EG-K vol.1
Ref.No.

Part No.
Pcs
411
VQT3N55
411
VQT3N53
413
413
VPK5005
VPK5006
413
414
415
VPK5007
VPN7251
VPN7253
PACKING CASE
PAD A
PAD D
416
VPN7252
PAD B
417
417
418
419
421
421
421
421
421
VQL2C67-A
VQL2C68-1A
VQL2J61
VQL1Z76
VQL2H32
VQL2M24
VQL1Z66
VQL2M25
VQL1Z69
OPERATING LABEL
OPERATING LABEL
GD LABEL
NTSC LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
421
VQL2B13
COLOR LABEL
1 KEE
421
421
422
422
422
422
422
VQL2H31
VQL2F42
VQL2H32
VQL2M24
VQL1Z66
VQL2M25
VQL1Z69
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
1 KGC,KGH
422
VQL2B13
COLOR LABEL
1 KGK
422
422
423
423
423
423
423
VQL2H31
VQL2F42
VQL2H32
VQL2M24
VQL1Z66
VQL2M25
VQL1Z69
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
1 KEG
423
VQL2B13
COLOR LABEL
1 KEG
423
423
424
425
426
427
450
451
451
453
453
454
460
VQL2H31
VQL2F42
VFC4315
VYF3201
VPF1438
VYC1009
K2CT3YY00034
K2CQ2YY00082
K2CR2YY00026
K2CA2YY00129
K2CA2YY00130
K2CJ2YY00052
VFF0800-S
COLOR LABEL
COLOR LABEL
LENS REAR CAP
LENS CAP
LENS BAG
LENS HOOD
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
CD-ROM(APPLI-OVERSEAS)
460
VFF0801-S
CD-ROM (APPLI-CHINA)
1
1
1
1
1
1
1
404
405
406
K1HY08YY0015 USB CABLE W/PLUG

K1HY08YY0016 AV CABLE W/PLUG
VFC4634
SHOULDER STRAP
1
1
1
407
407
407
407
407
408
409
410
VFF0806
VFF0805
VFF0807
VFF0808
VFF0809
VGQ0C14
VPF1100
VQC8410
1
1
1
1
1
1
1
1
410
VQC8408
410
VQC8409
417
VQC8411
410
VQC8412
410
VQC8413
410
VQC8414
410
VQC8417
410
VQC8416
411
VQT3N43
411
VQT3N44
411
VQT3N40
411
VQT3N41
411
VQT3N42
411
VQT3N45
411
VQT3N46
411
VQT3N47
411
VQT3N48
411
VQT3N49
411
VQT3N50
411
VQT3N51
411
VQT3N52

BASIC O/I
(ENGLISH)
BASIC O/I
(KOREAN)
BASIC O/I
(CHINESE(SIMPLIFIED))
PACKING CASE
PACKING CASE
BODY CAP
CAMERA BAG
BATTERY CHARGER
BATTERY CHARGER
BATTERY CHARGER
BATTERY CHARGER
BATTERY
VQC8415
Part No.
VQT3N54
VKF4385
VPF1316A
DE-A94AA/SX
DE-A93BA/SX
DE-A94BB/SX
DE-A94CA/SX
-----
410
Ref.No.
411
400
401
402
402
402
402
403
CD-ROM (INSTRUCTION BOOK)

TOUCH PEN
BAG, POLYETHYLENE
O/I SOFTWARE
(GERMAN/FRENCH/ITALIAN/
DUTCH)
O/I SOFTWARE
(ENGLISH/SPANISH/
PORTUGUESE)
O/I SOFTWARE
(ENGLISH/CANADIAN FRENCH)
O/I SOFTWARE
(SPANISH/PORTUGUESE/
SWEDISH/DANISH/FINNISH)
O/I SOFTWARE
(ENGLISH)
O/I SOFTWARE
(RUSSIAN/UKRAINIAN)
O/I SOFTWARE
(ENGLISH/
CHINESE(TRADITIONAL)/
ARABIC)
O/I SOFTWARE
(CHINESE(TRADITIONAL))
O/I SOFTWARE
(KOREAN)
O/I SOFTWARE
BASIC O/I
(GERMAN/FRENCH)
BASIC O/I
(ITALIAN/DUTCH)
BASIC O/I
(ENGLISH/SPANISH)
BASIC O/I
(PORTUGUESE)
BASIC O/I
BASIC O/I
(SPANISH/PORTUGUESE)
BASIC O/I
(SWEDISH/DANISH)
BASIC O/I
(FINNISH)
BASIC O/I
(ENGLISH)
BASIC O/I
(RUSSIAN/UKRAINIAN)
BASIC O/I
(ENGLISH/
CHINESE(TRADITIONAL))
BASIC O/I
(ARABIC)
BASIC O/I
Remarks
(G3K)
(G3K)
KEG,KEC,KEB,KEE,KGN
KPP,KPC
KGC,KGH,KGK,KGD
KGT
KEG,KEC,KEB,KEE,KGC,KGH,
KGT,KGN,KGD,KGK,KPP,KPC
(G3K)
(G3K)
KPP,KPC,KEG,KEC,KEB,KEE,
KGC,KGH,KGT,KGK,KGN,KGD
KEG,KEC,KEB
KPP,KPC
KEE,KGC,KGH,KGN
KGT,KGD
KGK
(G3K)
(G3K)
KEG
1 KPP
1 KPC
1 KEC
1 KEB,KGN
1 KGT
1 KGD
1 KPP
1 KPP
1 KPC

1 KEC
1 KEC
1 KEC
1 KEB
1 KEE
1 KGC,KGH
1 KGC
1 KGT
S-19
Pcs
Remarks
1 KGN
1 KGD
1 KGK
1 KPP,KPC
1 KEG,KEC,KEB,KEE,KGC,KGH,
KGT,KGN,KGD
1 KGK
1 (G3K)
1 KPP,KPC,KEG,KEC,KEB,KEE,
1 KPC
1 KGT
1 KGD
1 KGT,KGD
1 KPP-W
1 KPP-T
1 KPP-R,KPC-R
1 KEG-T,KGC-T
1 KEG-R,KEC-R,KEB-R,KEE-R,
KGC-R,KGH-R,KGN-R
1 KEC-W,KEB-W,KEE-W,KGC-W,
KGH-W,KGT-W,KGN-W,KGD-W
1 KGK-W
1 KGK-R
1 KPP-W
1 KPP-T
1 KPP-R,KPC-R
1 KEG-T,KGC-T
KGC-R,KGH-R,KGN-R
1 KGK-W
1 KGK-R
1 KPP-W
1 KPP-T
1 KPP-R,KPC-R
1 KEG-T,KGC-T
KGC-R,KGH-R,KGN-R
1 KGK-W
1 KGK-R
1 (G3K) [SPC]
1 (G3K) [SPC]
1 (G3K) [SPC]
1 (G3K) [SPC]
1 KEB,KGC,KGH
1 KEG,KEC,KEE,KGC
1 KGD
1 KGT
1 KGK
1 KGN
KGC,KGH,KGT,KGN,KGD
[SPC]See "Notes"
1 KGK [SPC] See "Notes"
DMC-G3EG-K vol.1
Ref.No.

Part No.
Pcs
513
513
514
515
VPK5081
VPK5011
VPN7251
VPN7254
PACKING CASE
PACKING CASE
PAD A
PAD C
516
VPN7252
PAD B
517
518
519
521
521
VQL2C68-1A
VQL2J61
VQL1Z76
VQL2M25
VQL1Z69
OPERATING LABEL
GD LABEL
NTSC LABEL
COLOR LABEL
COLOR LABEL
521
VQL2B13
COLOR LABEL
521
521
522
522
VQL2H31
VQL2F42
VQL2M25
VQL1Z69
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
522
VQL2B13
COLOR LABEL
522
522
523
523
VQL2H31
VQL2F42
VQL2M25
VQL1Z69
COLOR LABEL
COLOR LABEL
COLOR LABEL
COLOR LABEL
1 WEB,WGN
523
VQL2B13
COLOR LABEL
1 WEE
523
523
524
525
526
527
528
529
530
531
550
551
551
553
553
554
560
VQL2H31
VQL2F42
VFC4315
VYF3201
VPF1438
VYC1009
VFC4315
VYF3201
VPF1316
VYC0986
K2CT3YY00034
K2CQ2YY00082
K2CR2YY00026
K2CA2YY00129
K2CA2YY00130
K2CJ2YY00052
VFF0800-S
COLOR LABEL
COLOR LABEL
LENS REAR CAP
LENS CAP
LENS BAG
LENS HOOD
LENS REAR CAP
LENS CAP
LENS BAG
LENS HOOD
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
CD-ROM(APPLI-OVERSEAS)
560
VFF0801-S
CD-ROM (APPLI-CHINA)
1
1
1
1
1
1
1
504
505
506

VFC4634
SHOULDER STRAP
1
1
1
506
507
507
507
507
507
508
509
510
VFC4717
VFF0806
VFF0805
VFF0807
VFF0808
VFF0809
VGQ0C14
VPF1100
VQC8410
1
1
1
1
1
1
1
1
1
510
VQC8408
510
VQC8412
510
VQC8413
510
VQC8414
510
VQC8415
510
VQC8417
510
VQC8416
511
VQT3N43
511
VQT3N44
511
VQT3N40
511
VQT3N41
511
VQT3N45
511
VQT3N46
511
VQT3N47
511
VQT3N48
511
VQT3N49
511
VQT3N50
511
VQT3N51
511
VQT3N52
511
VQT3N54
511
VQT3N55
511
VQT3N53

PACKING CASE
PACKING CASE
BODY CAP
CAMERA BAG
BATTERY CHARGER
BATTERY CHARGER
BATTERY CHARGER
BATTERY CHARGER
BATTERY
VQC8411
Part No.
VPK5009
VPK5010
VKF4385
VPF1316A
DE-A94AA/SX
DE-A93BA/SX
DE-A94BB/SX
DE-A94CA/SX
-----
510
Ref.No.
513
513
500
501
502
502
502
502
503
SHOULDER STRAP
TOUCH PEN
BAG, POLYETHYLENE
O/I SOFTWARE
DUTCH)
O/I SOFTWARE
(ENGLISH/SPANISH/
PORTUGUESE)
O/I SOFTWARE
O/I SOFTWARE
(ENGLISH)
O/I SOFTWARE
(RUSSIAN/UKRAINIAN)
O/I SOFTWARE
(ENGLISH/
ARABIC)
O/I SOFTWARE
O/I SOFTWARE
(KOREAN)
O/I SOFTWARE
BASIC O/I
(GERMAN/FRENCH)
BASIC O/I
(ITALIAN/DUTCH)
BASIC O/I
(ENGLISH/SPANISH)
BASIC O/I
(PORTUGUESE)
BASIC O/I
BASIC O/I
(SWEDISH/DANISH)
BASIC O/I
(FINNISH)
BASIC O/I
(ENGLISH)
BASIC O/I
(RUSSIAN/UKRAINIAN)
BASIC O/I
(ENGLISH/
BASIC O/I
(ARABIC)
BASIC O/I
BASIC O/I
(ENGLISH)
BASIC O/I
(KOREAN)
BASIC O/I
Remarks
(G3W)
(G3W)
WEG,WEC,WEB,WEE,WGN
WPP
WGC,WGH,WGK,WGD
WGT
WEG,WEC,WEB,WEE,WGN,WGC,
WGH,WGK,WGD,WGT,WPP
(G3W)
(G3W)
WPP,WEG,WEC,WEB-K/R,WEE-K,
WGC,WGH,WGT,WGN,WGD,WGK
WEB-KA
WEG,WEC,WEB
WPP
WEE,WGC,WGH,WGN
WGT,WGD
WGK
(G3W)
(G3W)
WEG
1 WPP
1 WEC
1 WGC,WGH
1 WGT
1 WGD
1 WGK
1 WEG
1 WEG
1 WPP

1 WPP
1 WEC
1 WEC
1 WEC
1 WEB
1 WEE
1 WGC,WGH
1 WGC
1 WGT
1 WGN
1 WGD
1 WGK
S-20
Pcs
Remarks
1 WPP-K
1 WEG,WEC,WEB-K/R,WEE-K,
WGC,WGH,WGT,WGN,WGD
1 WEB-KA
1 WGK
1 (G3W)
1 WPP,WEG,WEC,WEB,WEE,WGC,
WGH,WGT,WGK,WGN,WGD
WGH,WGT,WGK,WGN,WGD
1 WGT
1 WGD
1 WGT,WGD
1 WEG-T,WGC-T
1 WEG-R,WEC-R,WEB-R,WGC-R,
WGH-R,WGN-R
1 WEC-W,WGC-W,WGH-W,WGT-W,
WGN-W,WGD-W
1 WGK-W
1 WGK-R
1 WEG-T,WGC-T
WGH-R,WGN-R
WGN-W,WGD-W
1 WGK-W
1 WGK-R
1 WEG-T,WGC-T
WGH-R,WGN-R
WGN-W,WGD-W
1 WGK-W
1 WGK-R
1 (G3W) [SPC]
1 (G3W) [SPC]
1 (G3W) [SPC]
1 (G3W) [SPC]
1 (G3W) [SPC]
1 (G3W) [SPC]
1 (G3W) [SPC]
1 (G3W) [SPC]
1 WEB,WGC,WGH
1 WEG,WEC,WEE,WGC
1 WGD
1 WGT
1 WGK
1 WGN
WGH,WGT,WGN,WGD
[SPC] See "Notes"
1 WGK [SPC] See "Notes"
DMC-G3EG-K vol.1
Ref.No.
Part No.
Pcs
600
601
602
602
602
602
603
VKF4385
VPF1316A
DE-A94AA/SX
DE-A93BA/SX
DE-A94BB/SX
DE-A94CA/SX
-----
BODY CAP
CAMERA BAG
BATTERY CHARGER
BATTERY CHARGER
BATTERY CHARGER
BATTERY CHARGER
BATTERY
1
1
1
1
1
1
1
604
605
606

VFC4634
SHOULDER STRAP
1
1
1
607
607
607
607
608
609
610
VFF0805
VFF0807
VFF0808
VFF0806
VGQ0C14
VPF1100
VQC8410
1
1
1
1
1
1
1
610
VQC8408
610
VQC8411
610
VQC8412
610
VQC8413
610
VQC8414
610
VQC8415
610
VQC8417
610
VQC8409
611
VQT3N42
611
VQT3N43
611
VQT3N44
611
VQT3N40
611
VQT3N41
611
VQT3N45
611
VQT3N46
611
VQT3N47
611
VQT3N48
611
VQT3N49
611
VQT3N50
611
VQT3N51
611
VQT3N52
611
VQT3N54
611
VQT3N55


TOUCH PEN
BAG, POLYETHYLENE
O/I SOFTWARE
DUTCH)
O/I SOFTWARE
(ENGLISH/SPANISH/
PORTUGUESE)
O/I SOFTWARE
O/I SOFTWARE
(ENGLISH)
O/I SOFTWARE
(RUSSIAN/UKRAINIAN)
O/I SOFTWARE
(ENGLISH/
ARABIC)
O/I SOFTWARE
O/I SOFTWARE
(KOREAN)
O/I SOFTWARE
BASIC O/I
BASIC O/I
(GERMAN/FRENCH)
BASIC O/I
(ITALIAN/DUTCH)
BASIC O/I
(ENGLISH/SPANISH)
BASIC O/I
(PORTUGUESE)
BASIC O/I
BASIC O/I
(SWEDISH/DANISH)
BASIC O/I
(FINNISH)
BASIC O/I
(ENGLISH)
BASIC O/I
(RUSSIAN/UKRAINIAN)
BASIC O/I
(ENGLISH/
BASIC O/I
(ARABIC)
BASIC O/I
BASIC O/I
(ENGLISH)
BASIC O/I
(KOREAN)
Remarks
Ref.No.
(G3)
(G3)
EG,EC,EB,EE,GN
PP,PC
GC,GH,GD
GT
EG,EC,EB,EE,GC,GH,GT,GN,GD,
PP,PC
(G3)
(G3)
EG,PP,PC,EC,EB,EE,GC,GH,
GT,GN,GD
PP,PC
EE,GC,GH,GN
GT,GD
EG,EC,EB
(G3)
(G3)
EG
1 PP
1 EC
1 EB,GN
1 EE
1 GC,GH
1 GT
1 GD
1 PC
1 PC
1 EG
1 EG
1 PP
1 PP
1 EC
1 EC
1 EC
1 EB
1 EE
1 GC,GH
1 GC
1 GT
1 GN
1 GD
S-21

Part No.
613
VPK5003
PACKING CASE
613
614
615
VPK5002
VPN7251
VPN7253
PACKING CASE
PAD A
PAD D
616
VPN7261
PAD B
617
617
618
619
650
651
651
653
654
660
VQL2C67-A
VQL2C68-1A
VQL2J61
VQL1Z76
K2CT3YY00034
K2CQ2YY00082
K2CR2YY00026
K2CA2YY00129
K2CJ2YY00052
VFF0800-S
OPERATING LABEL
OPERATING LABEL
GD LABEL
NTSC LABEL
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
AC CORD W/PLUG
CD-ROM (APPLI-OVERSEAS)
Pcs
Remarks
1 EG-K,EC-K,EB-K,EE-K,GC-K,
GH-K,GT-K,GN-K,GD-K
1 PP-K,PC-K
1 (G3)
1 EG,PP,PC,EC,EB,EE,GC,GH,
GT,GN,GD
GT,GN,GD
1 PC
1 GT
1 GD
1 GT,GD
1 EB,GC,GH
1 EG,EC,EE,GC
1 GD
1 GT
1 GN
GT,GN,GD
[SPC] See "Notes"
S7. Exploded View

S7.1. Frame and Casing Section
59
68
62
66
61
65
67
B21
B20
57
B55
B54
90
89
64
93-1
69
10
89-1
B57 60
B53
B56
B51
B12
B52 15
B13
3
93
91
14
8
B63 B64
63
B50
11
12
B14
B15
2
75
B61
B62
82
1
B48
56
74
78
B8
B42
B43
17-3
B30
17
72 73
81
B60
34
17-5
B41
B1
35
32
31
29
23
18
94
B36
50
B37
42
B44
B45
B3
B4
45
B23
36
B2
22
38
B22
B7
30
25
B24
B25
B26
B38
B39
B27
B59
B40
21
28
B17
B16
26
17-4
B18
B19
33
17-6
80
85
37
B6
B49
84
88
39
B5
71
16
17-7
17-9
86
83
B11
27
17-2
B58
87
77 92
B33
17-1
76
79
B9
B10
B31 B32
17-8
13
24
43 40
B46
B47
B34
B35
S-22
41
44
46
S7.2. Camera Lens Section (1)
213
207
B204
B205
B206
B207
208
204
B220
B221
B201
B222
B202
B203
B208
B209
202
B210
B211
206
209
210
B213
212
203
211
S-23
S7.3. Camera Lens Section (2)
305
313
B313
309
304
B317
308
310
B301 B303
B304
302
B302
B305
303
B306
B318
B309
306
B311
B308
B310
B312
307
S-24
B307
S7.4. Packing Parts and Accessories Section (1)

411
407
460
417
410
409
406
Except PP,PC
403
(DMC-G3KEB/GC/GH)
,PC
450
408
405
t
ep
PP
400
Ex
415
404
(DMC-G3KEC/EE/EG/GC/GD)
On
ly
451
PP
,P
427
(DMC-G3KGT/GK)
401
453
402
425
(DMC-G3KGN)
426
454
424
414
421
416
418
419
413
Directions for putting Color Labels,
NTSC LABEL and GD LABEL.
* Except black color model, stick each color label
(Ref. No.421,422,423) inside the color indication frame
making sure that the bottom part of the color label is
423
even inside the color indication frame.
* Stick NTSC LABEL (Ref. No.419) to printed PAL of the
packing case for [GD] and [GT] models.
* Stick GD LABEL (Ref. No.418) for [GD] model on the
original printed place.
422
S-25

511
507
560
517
510
503
509
531
530
529
506
528
Except PP,PC
515
(DMC-G3WEB/GC/GH)
550
505
tP
ep
508
,PC
c
Ex
500
504
(DMC-G3WEC/EE/EG/GC/GD)
On
ly
551
PP
,P
527
(DMC-G3WGT/GK)
501
553
502
525
(DMC-G3WGN)
526
554
524
514
521
516
518
519
513
Directions for putting Color Labels,
NTSC LABEL and GD LABEL.
* Except black color model, stick each color label
(Ref. No.521,522,523) inside the color indication frame
making sure that the bottom part of the color label is
523
even inside the color indication frame.
522
S-26

611
607
660
617
610
609
600
606
603
Except PP,PC
(DMC-G3EB/GC/GH)
601
pt
ce
650
Ex
608
,P
PP
602
615
605
604
(DMC-G3EC/EE/EG/GC/GD)
651
On
ly
614
PP
,P
(DMC-G3GT)
653
616
(DMC-G3GN)
654
618
619
613
Directions for putting NTSC LABEL and GD LABEL.
S-27

G3 PDF

Uploaded by

Copyright:

Available Formats

G3 PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

G3 PDF

Uploaded by

Copyright:

Available Formats

ORDER NO.

Digital Camera/Lens Kit/Double Zoom Lens Kit/Body

1. IMPORTANT SAFETY NOTICE

1. Plug the AC cord directly into the AC outlet. Do not use

in the Schematic Diagrams, Circuit Board Layout,

Leakage Current Hot Check

Leakage Current Cold Check

1. Unplug the AC cord and connect a jumper between the

How to Discharge the E. Capacitor on Flash P.C.B.

Prevention of Electrostatic Discharge (ESD) to Electrostatically

How to Recycle the Lithium Ion Battery (U.S. Only)

Caution for AC Cord

Information for Your Safety

The wires in this mains lead are coloured in accordance with

As the colours of the wires in the mains lead of this appliance

Caution for AC Mains Lead

For your safety, please read the following text carefully.

Remove the Connector Cover as follows.

If the plug contains a removable fuse cover you must ensure

How to Replace the Fuse

1. Remove the Fuse Cover with a screwdriver.

If the fitted moulded plug is unsuitable for the socket outlet in

2. Replace the fuse and attach the Fuse cover.

How to Replace the Lithium Battery

1. Remove the MAIN P.C.B.. (Refer to Disassembly Procedures.)

Camera Body Unit

About Mount Box Unit (Ref. 16)

About Flexible Cable and Connector

About Main P.C.B. (Ref. 1) / LCD IF P.C.B. (Ref. 40)

Lens Unit (Interchangeable Lens: H-FS014042)

Lens Unit (Interchangeable Lens: H-FS045200)

General Description About Lead Free Solder (PbF)

How to Define the Model Suffix (NTSC or PAL model)

[CASE 2. Other than "After replacing MAIN P.C.B."]

Step 5. Choose the model suffix in INITIAL SETTINGS: (Refer to CAUTION)

5 Location of Controls and Components

21 Shoulder strap eyelet

Focus distance reference mark

Selecting the Recording Mode

Switching the mode by rotating the mode dial.

To select Intelligent Auto Mode

To touch and release the touch panel.

A movement without releasing the touch

Use this to perform tasks such as selecting

This is used to move the AF area, operate

panel, be sure to touch the center of the

About the Stylus pen

Error Code Memory Function

Example of Error Code Display

Error Code List:

Important notice about Error Code List

Checking Method of Body and Interchangeable Lens

8 Service Fixture & Tools

Service Fixture and Tools

CAUTION-1. (When servicing FLASH P.C.B.)

9 Disassembly and Assembly Instructions

Camera Body Part

This is a disassembling chart.

Front Case Unit