Elc-Copbdp Instruction Sheet: ELC PA/PB/PC/PH Controllers Profibus/DP Slave Adapter

IL05003018E.
pdf
2006-02-10
FUNCTION SPECIFICATIONS
2
Item
5011640000-DP00
ELC-COPBDP
Instruction Sheet
ELC PA/PB/PC/PH Controllers

Profibus/DP Slave Adapter
WARNING
This Instruction Sheet only provides descriptions for electrical specifications, general specifications,
DP Connections
Interface
DB9 9 pin connector
Transfer method
High speed RS485
Transfer cable
2-wire twisted shielded cable
Electrical isolation
500V DC
Communications
Message types
DPV0, Cyclical data exchange process
Device ID
09B9 HEX
GSD file
EATN09B9.GSD
Model Name
ELC-COPBDP
9.6K bps
19.2K bps
This is an OPEN TYPE Controller. The ELC-COPBDP should be kept in an enclosure away from
93.75K bps
airborne dust, humidity, electric shock risk and vibration.
501-10(B)(1) of the National Electrical Code.
Baud rates
(Auto detected)
500K bps
1.5M bps
Suitable for use in Class 1, Division 2, Groups A, B, C, D or Non-Hazardous locations only.
3M bps
6M bps
Warning Explosion hazard - Substitution of components may impair suitability for Class 1, Division 2.
Warning Explosion hazard - Do not disconnect equipment unless power has been switched off or the area
is known to be Non-Hazardous.
Use a screwdriver to lift and unfasten the fixing clip.
187.5K bps
Power, input and output (I/O) wiring must be in accordance with Class 1, Div. 2 wiring methods - Article
OVERVIEW
12M bps
Environmental specifications
Noise Immunity
ESD(IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

EFT(IEC 61131-2, IEC 61000-4-4): Power Line: 2KV, Digital I/O: 1KV, Analog &
Communication I/O: 1KV
RS(IEC 61131-2, IEC 61000-4-3): 26MHz~1GHz, 10V/m
Environment
Operation: 0 ~55
Storage: -25 ~70
ELC-COPBDP: Profibus/DP Slave Module for ELC Series Controllers
(Temperature), 50~95% (Humidity), Pollution degree 2;

(Temperature), 5~95% (Humidity)
Vibration / Shock Resistance
POWER
NET
Address switch
UL1604, Class1,Div2
Agency Approvals
Operating temperature code: T5
European community EMC Directive 89/336/EEC and Low Voltage Directive
x16
73/23/EEC
ELC-COPBDP
Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)

IEC61131-2 & IEC 68-2-27 (TEST Ea)
UL508
x16
Extension port
Open the extension cover with a screwdriver.
Specification
installation and wiring.
Power LED
Net LED
Installing the ELC-COPBDP with the ELC controller
INSTALLATION AND CONFIGURATION
Connect the ELC-COPBDP to extension port of ELC controller and fasten the fixing clip.
Dimensions
Dimensions are in millimeter and [inch]
Profibus connector
POWER
POWER
ss
RUN
NET
ERROR
1
x16
BAT.LOW
X0
POWER
NET
X1
x16
X2
0
x16
X3
Support the SYNC and FREEZE for data synchronization between master and slaves.
Support Auto Baud rate detection.
Support 12MHz baud rate in DP network.
Cyclical data size is fixed to 4bytes input and 4bytes output.
Support GSD file configures by using configuration tools.
Y0
C1
Y1
C2
Y2
Y3
ELC-CDPBDP
63.4 [2.50]
Cyclical data exchange process.
X7
C0
RS-232
RS-485
STOP
60 [2.36]
x16
X6
ELC-PC12NNDR
Function
X4
X5
ELC-COPBDP
90 [3.54]
RUN
IL05003018E.pdf
Plug the PROFIBUS connector to the socket of ELC-COPBDP, and tighten screw to secure the connector.
Configure ELC-COPBDP to Profibus-DP

LED Status
Indication
Corrective Actions
Red ON
No connection to PROFIBUS
Verify that DP network installation is OK.

Verify that PLC is working.
Verify that switch address setting match with
configuration in DP master.
Green blinking
Reserved
Cyclic data exchange in
progress and OK
No action.
LED Status
Indication
Corrective Actions
Green ON
Power on
No action needed.
OFF
No power
Verify that ELC Controller is powered on.
Connecting example as follow:
PC with master card
Green ON
Profibus network
No action.
Power LED
ELC-PS01
ELC-PC12NNDR
ELC-COPBDP
POWER
RUN
X0
ERROR
POWER
NET
X1
BAT.LOW
x16
X2
X3
RUN
X4
APPENDIX PROFIBUS-DP
x16
X5
X6
X7
ELC-PC12NNDR
STOP
The Maximum cable length in a segment depends on the transmission speed. PROFIBUS-DP communicates at
Y1
Y2
Y3
ELC-COPBDP
Y0
C1
C2
PROFIBUS is an international, vendor- independent, opening filed bus standard for a wide range of applications in
RS-232
RS-485
Limitation of Cable length vs. Baudrate
PROFIBUS
C0
the fields of manufacturing, production, process and building automation, and other automation control field.
speeds from 9.6 Kbps to 12 Mbps over distances from 100 to 1,200 meters.
The PROFIBUS family comprises three types of protocol, PROFIBUS-DP, PROFIBUS-PA and PROFIBUS-FMS,
Baud Rate (bps)
9.6K
19.2K
93.75K
187.5K
500K
1.5M
3M
6M
12M
Length (m)
1200
1200
1200
1000
400
200
100
100
100
ELC-COPBDP provides fixed 4bytes input data and 4bytes output data to user in Profibus-DP system. 4bytes input
each of them is used for different tasks:
data are transmitted from ELC-COPBDP module to Profibus-DP Master, it are mapping to Y20-Y57 in ELC
And check the extension I/O by ELC software:

Connecting to ELC controller
Once connection is successful, software will check

if 32 inputs/outputs is detected.
controller when ELC-COPBDP is the first extension unit of ELC. 4bytes output data are transmitted from
PROFIBUS-DP (Decentralized Periphery): PROFIBUS-DP is a rapid and low cost communication connection
Profibus-DP Master, and it are also mapping to X20-X57 in ELC controller.
mainly designed for high-speed modem. PROFIBUS-DP has widespread usage for such items as remote I/O
systems, motor control centers, and variable speed drives. It is designed and optimized especially for
And the data mapping as follow:
communication between automation systems and decentralized peripheral devices.
4 bytes output
X20~X57
From DP Master
PROFIBUS-PA (Process Automation): PROFIBUS-PA is the PROFIBUS solution for process automation, typically
ELC-Pxxxxxxx
ELC-COPBDP
Y20~Y57
4 bytes input
with MBP-IS transmission technology. Based upon PROFIBUS-DP, PROFIBUS-PA is an extension of the
PROFIBUS-DP protocol for data transmission. It is designed to support intrinsically safe applications and can be
To DP Master
used within hazardous areas, with high explosion risk using intrinsic safe MBP-IS interface. PROFIBUS-PA is used
to connect sensor and controller to the bus.
One example ladder program as follow:
PROFIBUS-FMS (Fieldbus Message Specification): PROFIBUS-FMS is multiple master communications designed

for communication at the cell level. It is designed for acyclic or cyclic data transfers at medium speed between
M1000
DP Connector Assignment
Pin
Designation
Content
--
NC
--
NC
RxD/TxD-P
Data receiving/sending P (B)
--
NC
DGND
Data reference potential (C)
VP
Positive voltage
--
NC
RxD/TxD-N
Data receiving/sending N (A)
--
NC
MOV
K4X20
D10
MOV
K4X40
D11
MOV
D20
K4Y20
MOV
D21
K4Y40
This program example copies the 4 bytes data from X20-X57 that transmitted by DP master to D10 and D11
registers in ELC controller. And, ELC controller will write 4 bytes data in D20 and D21 registers to Y20-Y57, these 4
bytes data will send to ELC-COPBDP, and ELC-COPBDP will send these data to DP master.
TROUBLESHOOTING
NET LED
MAC ID setting for ELC-COPBDP module
Address
Content
LED Status
Indication
Corrective Actions
OFF
No power supply
Invalid PROFIBUS address
setting via switch
Verify ELC-COPBDP is powered on.

Check whether the switch setting is valid. Setting range
of slave: 1-125. Set the valid value and re-power.
Communication link to
PROFIBUS, and No cyclical
data exchanged
No action.
x16
1 .. 0x7D
Valid PROFIBUS Address.
Red blinking (rapidly)
0 or
Invalid PROFIBUS Address. NET LED will rapidly
0x7E .. 0xFF blink with RED when node address is at 0, 0x7E~
0xFF.
x16
Red blinking
control equipment and cell-level controllers. FMS services open up a wide range of applications and offer a wide
range of functionality and flexibility.

Elc-Copbdp Instruction Sheet: ELC PA/PB/PC/PH Controllers Profibus/DP Slave Adapter

Uploaded by

Copyright:

Available Formats

Elc-Copbdp Instruction Sheet: ELC PA/PB/PC/PH Controllers Profibus/DP Slave Adapter

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Elc-Copbdp Instruction Sheet: ELC PA/PB/PC/PH Controllers Profibus/DP Slave Adapter

Uploaded by

Copyright:

Available Formats

IL05003018E.

ELC PA/PB/PC/PH Controllers

DB9 9 pin connector

High speed RS485

2-wire twisted shielded cable

DPV0, Cyclical data exchange process

airborne dust, humidity, electric shock risk and vibration.

501-10(B)(1) of the National Electrical Code.

Suitable for use in Class 1, Division 2, Groups A, B, C, D or Non-Hazardous locations only.

Use a screwdriver to lift and unfasten the fixing clip.

ESD(IEC 61131-2, IEC 61000-4-2): 8KV Air Discharge

ELC-COPBDP: Profibus/DP Slave Module for ELC Series Controllers

(Temperature), 50~95% (Humidity), Pollution degree 2;

Vibration / Shock Resistance

Operating temperature code: T5

European community EMC Directive 89/336/EEC and Low Voltage Directive

Standard: IEC61131-2, IEC 68-2-6 (TEST Fc)

Open the extension cover with a screwdriver.

installation and wiring.

Installing the ELC-COPBDP with the ELC controller

INSTALLATION AND CONFIGURATION

Support Auto Baud rate detection.

Support 12MHz baud rate in DP network.

Cyclical data size is fixed to 4bytes input and 4bytes output.

Support GSD file configures by using configuration tools.

Cyclical data exchange process.

Configure ELC-COPBDP to Profibus-DP

Verify that DP network installation is OK.

Verify that ELC Controller is powered on.

Connecting example as follow:

PC with master card

Limitation of Cable length vs. Baudrate

each of them is used for different tasks:

And check the extension I/O by ELC software:

Once connection is successful, software will check

Profibus-DP Master, and it are also mapping to X20-X57 in ELC controller.

And the data mapping as follow:

communication between automation systems and decentralized peripheral devices.

One example ladder program as follow:

PROFIBUS-FMS (Fieldbus Message Specification): PROFIBUS-FMS is multiple master communications designed

Data receiving/sending P (B)

Data reference potential (C)

Data receiving/sending N (A)

Verify ELC-COPBDP is powered on.

Valid PROFIBUS Address.

Red blinking (rapidly)

You might also like