Shimano Dealers Manual

DM-GN0001-18
(English)
Dealer's Manual
General Operations
CONTENTS
IMPORTANT NOTICE............................................................................................................ 7
TO ENSURE SAFETY............................................................................................................. 8
REAR DERAILLEUR
TO ENSURE SAFETY........................................................................................................... 10
REAR DERAILLEUR FOR MTB/TREKKING.......................................................................... 12
Installation of the rear derailleur....................................................................................................................... 12
Stroke adjustment............................................................................................................................................... 14
Securing the cable............................................................................................................................................... 16
SIS adjustment..................................................................................................................................................... 21
Replacing the pulley............................................................................................................................................ 23
REAR DERAILLEUR FOR ROAD.......................................................................................... 25

Installation of the rear derailleur....................................................................................................................... 25
Stroke adjustment............................................................................................................................................... 27
Securing the cable............................................................................................................................................... 30
SIS adjustment..................................................................................................................................................... 32
Replacing the pulley............................................................................................................................................ 34
FRONT DERAILLEUR
35
TO ENSURE SAFETY........................................................................................................... 36
FRONT DERAILLEUR FOR MTB/TREKKING........................................................................ 37
Installation........................................................................................................................................................... 37
Fixing the cable and adjusting the SIS (Front double)...................................................................................... 43
Fixing the cable and adjusting the SIS (Front triple)......................................................................................... 49
FRONT DERAILLEUR FOR ROAD........................................................................................ 53

Installation........................................................................................................................................................... 53
Fixing the cable and adjusting the SIS (Front double)...................................................................................... 55
Fixing the cable and adjusting the SIS (Front triple)......................................................................................... 60
MAINTENANCE.................................................................................................................. 66
CHAIN 67
TO ENSURE SAFETY........................................................................................................... 68
CHAIN CONNECTING PIN................................................................................................... 71
Method of use..................................................................................................................................................... 71
QUICK-LINK........................................................................................................................ 72
Installing QUICK-LINKs (SM-UG51)..................................................................................................................... 73
Installing QUICK-LINKs (SM-CN900-11).............................................................................................................. 75
Removing QUICK-LINKs (SM-CN900-11)............................................................................................................. 76
BRAKE 77
TO ENSURE SAFETY........................................................................................................... 78
DISC BRAKE........................................................................................................................ 82
Wheel spoke lacing............................................................................................................................................. 82
Installation of the disc brake rotor.................................................................................................................... 82
INSTALLATION (HYDRAULIC DISC BRAKES)..................................................................... 86

Installation of the brake lever............................................................................................................................ 86
Installation of the brake hose............................................................................................................................ 88
Installation of the brake hose (easy hose joint system).................................................................................... 92
Replacing the brake hose (easy hose joint system)........................................................................................... 97
Preventing loosening of frame fixing bolts..................................................................................................... 101
MAINTENANCE (HYDRAULIC DISC BRAKES).................................................................. 104

Brake pad replacement..................................................................................................................................... 104
Adjustment when the pistons are not operating correctly............................................................................ 107
Lever stroke adjustment................................................................................................................................... 108
Free stroke adjustment..................................................................................................................................... 108
Mineral oil replacement.................................................................................................................................... 108
Adding mineral oil and bleeding air................................................................................................................ 109
INSTALLATION (V-BRAKE BRAKES)................................................................................. 114

Installation of the brake lever.......................................................................................................................... 114
Installing the power modulator....................................................................................................................... 114
Installation of V-BRAKE brakes......................................................................................................................... 115
MAINTENANCE (V-BRAKE BRAKES)................................................................................ 118

Replacement of the cartridge shoe.................................................................................................................. 118
BRAKE LEVER WITH SWITCH INTERCHANGEABILITY

(V-BRAKE AND HUB ROLLER BRAKES)........................................................................... 119
For V-BRAKE (with power modulator) mode.................................................................................................. 119
For Caliper brake/Roller brake.......................................................................................................................... 119
INSTALLATION (DUAL PIVOT CALIPER BRAKES)............................................................ 120

Arch spring tension adjustment....................................................................................................................... 123
MAINTENANCE (DUAL PIVOT CALIPER BRAKES)........................................................... 124

Replacement of the cartridge shoe.................................................................................................................. 124
SPECIFICATIONS (CANTILEVER BRAKES)........................................................................ 125

Cantilever brakes............................................................................................................................................... 125
Brake lever......................................................................................................................................................... 125
INSTALLATION (CANTILEVER BRAKES)........................................................................... 126

Installation of the brake lever.......................................................................................................................... 126
Installation of the brake caliper....................................................................................................................... 127
Installing SM-CB70............................................................................................................................................. 130
FRONT CHAINWHEEL
131
TO ENSURE SAFETY......................................................................................................... 132

INSTALLATION (CHAINRINGS)......................................................................................... 134
For ROAD........................................................................................................................................................... 134
For MTB/Trekking.............................................................................................................................................. 135
INSTALLATION (FRONT CHAINWHEEL)........................................................................... 136

HOLLOWTECH II / 2 piece crankset................................................................................................................... 136
OCTALINK TYPE................................................................................................................................................. 141
SQUARE TYPE.................................................................................................................................................... 142
INSTALLATION (PRESS-FIT BOTTOM BRACKET)............................................................. 144

Adapter.............................................................................................................................................................. 144
Assembly example............................................................................................................................................. 144
Installation......................................................................................................................................................... 145
Removal............................................................................................................................................................. 146
PEDALS (SPD-SL PEDALS/SPD PEDALS)
147
TO ENSURE SAFETY......................................................................................................... 148

INSTALLATION (SPD PEDALS).......................................................................................... 150
Engaging the cleats with the pedals................................................................................................................ 150
Releasing the cleats from the pedals............................................................................................................... 150
Attaching the cleats.......................................................................................................................................... 152
Mounting the pedals on the crank arms......................................................................................................... 154
Adjusting the spring tension of the binding................................................................................................... 155
Cleat replacement............................................................................................................................................. 155
INSTALLATION (SPD-SL PEDALS)..................................................................................... 156

Cleat types......................................................................................................................................................... 156
Engaging the cleats with the pedals................................................................................................................ 157
Releasing the cleats from the pedals............................................................................................................... 157
Attaching the cleats.......................................................................................................................................... 157
Mounting the pedals on the crank arms......................................................................................................... 158
Adjusting the spring tension of the binding................................................................................................... 159
Cleat replacement............................................................................................................................................. 159
Replacement of the body cover....................................................................................................................... 160
Maintenance of the axle units.......................................................................................................................... 160
Mounting the reectors (optional).................................................................................................................. 160
HUB DYNAMO
161
TO ENSURE SAFETY......................................................................................................... 162

INSTALLATION (HUB DYNAMO)...................................................................................... 164
Installation of the disc brake rotor.................................................................................................................. 164
Installation of the front wheel......................................................................................................................... 164
CONNECTION OF THE CABLES........................................................................................ 167

For E2 type......................................................................................................................................................... 167
For J2 type.......................................................................................................................................................... 168
For J2-A type...................................................................................................................................................... 169
Note on the connection of the cables.............................................................................................................. 171
Checking the light illumination........................................................................................................................ 171
MAINTENANCE (HUB DYNAMO)................................................................................... 172
MULTIPLE FREEWHEEL
173
INSTALLATION (MULTIPLE FREEWHEEL)......................................................................... 174

Installation of the freewheel............................................................................................................................ 174
IMPORTANT NOTICE
IMPORTANT NOTICE
This dealer's manual is intended primarily for use by professional bicycle mechanics.
Users who are not professionally trained for bicycle assembly should not attempt to install the components themselves using the dealer's manuals.
If any part of the information on the manual is unclear to you, do not proceed with the installation. Instead, contact your place of purchase or a local
bicycle dealer for their assistance.
Make sure to read all instruction manuals included with the product.
Do not disassemble or modify the product other than as stated in the information contained in this dealer's manual.
All dealer's manuals and instruction manuals can be viewed on-line on our website (http://si.shimano.com).
Please observe the appropriate rules and regulations of the country, state or region in which you conduct your business as a dealer.
For safety, be sure to read this dealer's manual thoroughly before use, and follow it for correct use.
The following instructions must be observed at all times in order to prevent personal injury and physical damage to equipment and surroundings.
The instructions are classified according to the degree of danger or damage which may occur if the product is used incorrectly.
DANGER
Failure to follow the instructions will result in death or serious injury.
WARNING
Failure to follow the instructions could result in death or serious injury.
CAUTION
Failure to follow the instructions could cause personal injury or physical damage to equipment and surroundings.
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
Be sure to follow the instructions provided in the manuals when installing the product.
It is recommended to use genuine Shimano parts only. If parts such as bolts and nuts become loose or damaged, the bicycle may suddenly fall over,
which may cause serious injury.
In addition, if adjustments are not carried out correctly, problems may occur, and the bicycle may suddenly fall over, which may cause serious injury.
Be sure to wear safety glasses or goggles to protect your eyes while performing maintenance tasks such as replacing parts.
After reading the dealer's manual thoroughly, keep it in a safe place for later reference.
NOTE
Products are not guaranteed against natural wear and deterioration from normal use and aging.
For maximum performance we highly recommend Shimano lubricants and maintenance products.
REAR DERAILLEUR
REAR DERAILLEUR
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
Obtain and read the dealers manual carefully prior to installing the parts.
Loose, worn or damaged parts may cause the bicycle to fall over and serious injury may occur as a result. It is strongly recommended using only
genuine Shimano replacement parts.
If adjustments are not carried out correctly, the chain may come off. This may cause you to fall off the bicycle which could result in serious injury.
NOTE
If gear shifting operations cannot be carried out smoothly, clean the derailleur and lubricate all moving parts.
If the amount of looseness in the links is so great that adjustment is not possible, you should replace the derailleur.
Grease the inner cable and the inside of the outer casing before use to ensure that they slide properly.
For smooth operation, use the specified outer casing and the bottom bracket cable guide.
Periodically clean the derailleur and lubricate all moving parts (mechanism and pulleys).
If gear shifting adjustment cannot be carried out, check the degree of parallelism at the rear end of the bicycle. Also, check if the cable is lubricated
and if the outer casing is not too long or short.
If you hear abnormal noise as a result of looseness in a pulley, you should replace the pulley.
Using a frame with internal cable routing is strongly discouraged as it has tendencies to impair the SIS shifting function due to its high cable resistance.
For
MTB/Trekking
The gears should be periodically washed with a neutral detergent. In addition, cleaning the chain with neutral detergent and lubricating it can be an
effective way of extending the life of the gears and the chain.
Always be sure to use the sprocket set bearing the same group marks, and never use in combination with a
sprocket bearing a different group mark.
Group marks
a g -18T
a g -15
ag
-13
IM
SH
O
AN
HYPERG L I DE -C
Use an outer casing which still has some length to spare even when the handlebars are turned all the way to both sides. Furthermore, check that the
shifting lever does not touch the bicycle frame when the handlebars are turned all the way.
A special grease is used for the gear shifting cable. Do not use premium grease or other types of grease. These may cause deterioration in gear shifting
performance.
10
REAR DERAILLEUR
TO ENSURE SAFETY
For
ROAD
The end of the outer casing which has the aluminum cap should be at the
derailleur side.
Aluminum cap (4mm)

Derailleur side
Aluminum cap
When the chain is in any of the position combinations shown in the table, the
chain and sprocket may come into contact and generate noise. If the noise is a
problem, shift the chain onto the next largest sprocket or the one after.
Double
Chainring
Sprocket
11
Plastic cap
Triple
REAR DERAILLEUR
REAR DERAILLEUR FOR MTB/TREKKING
Installation of the rear derailleur

Standard type
Install the rear derailleur.
(A)
(A) 5mm hexagon wrench

(B) Fork end
(C) Bracket
Tightening torque
8 - 10 Nm
NOTE
Periodically check that there is no gap
between the fork end and the bracket as
shown in the illustration. If there is a gap
between these two parts, problems with gear
shifting performance may occur.
(B)
(C)
12
REAR DERAILLEUR
Bracket type
(C)
(A) Fork end

(B) Bracket bolt
(C) Bracket nut
(D) Bracket
Tightening torque
(A)
3 - 4 Nm
NOTE
(B)
Periodically check that there is no gap

between the fork end and the bracket as
shown in the illustration. If there is a gap
between these two parts, problems with gear
shifting performance may occur.
(D)
For BMX type
(A)
(D)
13
REAR DERAILLEUR
Stroke adjustment
Stroke adjustment
Top adjustment
(A)
(B)
B
Turn the top adjustment bolt to adjust so

that the guide pulley is in line with the
outer line of the smallest sprocket when
looking from the rear.
(A) Outer line of smallest sprocket

(B) Guide pulley
(C) Top adjustment bolt
Turn the low adjustment bolt so that the

guide pulley moves to a position directly
in line with the largest sprocket.
(A) Largest sprocket

(B) Guide pulley
(C) Low adjustment bolt
(C)
Low adjustment
(A)
(C)
(B)
A
14
REAR DERAILLEUR
Stroke adjustment
Chain length
The length of A will vary depending on
the movement of the rear suspension.
(z)
Consequently, an excessive load may be

placed on the drive system if the chain
length is too short.
The rear suspension operates and stops

when dimension A is at its greatest
extension.
(z)
(z) A
(A)
Mount the chain on to the largest

sprocket and the largest chainring.
(C)
(B)
Next, add 2 links to set the length of the

chain.

(B) Chain
(C) Largest chainring
(D) Pin/plate for preventing chain
derailment
(z) +2 links
(z)
NOTE
If there is a lot of movement in the rear
suspension, the slack in the chain may not
be taken up properly when the chain is on
the smallest chainring and smallest
sprocket.
The rear derailleur plate assembly is
(D)
(D)
15
equipped with a pin or plate that prevents

the chain from derailing.
When passing the chain through the rear
derailleur, pass it to the rear derailleur
body from the side of the pin/plate for
preventing chain derailment as shown in
the illustration.
If the chain is not passed through the
correct position, damage may be caused to
the chain or rear derailleur.
REAR DERAILLEUR
Securing the cable
Securing the cable

Cutting the outer casing
When cutting the outer casing, cut the
end opposite to the end with the
marking.
After cutting the outer casing, make the

end round so that the inside of the hole
has a uniform diameter.
After cutting, attach the same sealed

outer cap to the end.
(A)
Install the sealed outer cap with tongue and the rubber shield onto the outer casing stopper
of the frame.
(A)
(B)
(z)
(A) Outer cap
(z) Be careful not to bend this

section.
(A) Sealed outer cap with tongue

(B) Rubber shield
TECH TIPS
If the rear derailleur moves to a large degree,
such as in bicycles with rear suspension, it is
recommended that you replace the cap with
the accessory aluminum cap.
(B)
16
REAR DERAILLEUR
Securing the cable
Outer casing length for SHADOW RD

Loosen the B-tension adjust bolt until it
is in the position shown in the
illustration.
(A) B-tension adjust bolt
Check that there is enough slack in the

outer casing.
(A) Outer casing holder

(B) Outer casing
(A)
(A)
(B)
Next, align the outer casing with the

bottom edge of the holder on the rear
derailleur and then cut off any excess.
17
NOTE
The distance between the outer stopper to
the outer casing holder of the rear derailleur
may change when the rear suspension moves,
so determine the length of the outer casing at
the point where this length is at its greatest.
REAR DERAILLEUR
Securing the cable
Connecting and securing of the cable

Connect the inner cable to the rear
derailleur.
(A) Groove
(A)
Remove the initial slack from the cable

as shown in the illustration.
(z) Pull
2
(z)
Reconnect the inner cable to the rear

derailleur.
(A) Groove
Tightening torque
6 - 7 Nm
(A)
NOTE
Be sure that the cable is securely in the
groove.
To be continued on next page
18
REAR DERAILLEUR
Securing the cable
Set the inner cable so that the margin is

approximately 30mm or less.
Install the shift inner cap.
(z) 30mm or less
4
(z)
19
NOTE
Check that the inner cable does not interfere
with the wheel spokes.
Stop the wheel from turning while carrying
out this step.
REAR DERAILLEUR
Securing the cable
Using the B-tension adjust bolt

Mount the chain on the smallest
chainring and the largest sprocket, and
turn the crank arm for shifting.
(B)
(A)
(C)
A
A

(B) Smallest sprocket
(C) B-tension adjust bolt
Adjust the B-tension adjust bolt so that

the guide pulley does not interfere with
the sprocket but do not let the guide
pulley come so close to the chain that
they come into contact with each other.
Next, set the chain on the smallest
sprocket.
Repeat the above to make sure that the

pulley does not touch the sprocket.
Checking the distance between the largest sprocket and the guide pulley (SHADOW RD)
Set the rear derailleur to the largest
sprocket and, with the wheel stopped,
check that the distance between the tip
of the guide pulley and the tip of the
largest sprocket is within the range
indicated in the table.
[A]
Gear combination
[A]
11-36T
5 6mm
11-34T
5 6mm
11-32T
9 10mm
TECH TIPS
When the lower gear uses the gear
combination of 36T or 34T, set the distance to
5 to 6mm.
When the lower gear uses the gear
combination of 32T, set the distance to 9 to
10mm.
Turn the crank arm to shift gears and ensure that the shift is smooth.
NOTE
If the number of teeth for the cassette
sprocket is changed, try setting it again.
20
REAR DERAILLEUR
SIS adjustment
SIS adjustment
Confirming positioning on gear
Operate the shifting lever several times to move the chain to the 2nd sprocket counting
from the smallest sprocket.
Then, while operating the lever just enough to close the gap in the lever, turn the crank arm.
The best setting is when the shifting

lever is operated just enough to close the
lever gap and the chain touches the 3rd
sprocket counting from the smallest
sprocket and makes noise.
Adjusting SIS
When the chain shifts to the 3rd sprocket from the smallest sprocket
Tighten the cable adjustment barrel until the chain returns to the 2nd sprocket counting
from the smallest sprocket. (Clockwise)
(A)
(B)
21
(A) Cable adjustment barrel

(B) Adjustment bolt
REAR DERAILLEUR
SIS adjustment
When no sound at all is generated

Loosen the cable adjustment barrel until the chain touches the 3rd sprocket counting from
the smallest sprocket and makes a noise. (Counterclockwise)

(B) Adjustment bolt
(A)
(B)
Return the lever to its original position (the position where the lever is at the 2nd sprocket
setting counting from the smallest sprocket and it has been released) and then turn the
crank arm clockwise.
If the chain is touching the 3rd sprocket counting from the smallest sprocket and making a
noise, turn the cable adjustment barrel clockwise slightly to tighten it until the noise stops
and the chain runs smoothly.
Stop turning at the point where the noise just stops.
Operate lever to change gears, and check that no noise occurs in any of the gear positions.
TECH TIPS
For the best SIS performance, periodically
lubricate all power-transmission parts.
22
REAR DERAILLEUR
Replacing the pulley

Guide pulley
Replace the guide pulley.
(A) Guide pulley

(B) 3mm hexagon wrench
Tightening torque
2.5 - 5 Nm
(A)
NOTE
(B)
Check the arrow direction on the pulley when

installing it.
23
REAR DERAILLEUR
Tension pulley
Remove the E-ring first.
(A) E-ring
Replace the tension pulley.
(A) Tension pulley

1
(A)
(A)
Tightening torque
2.5 - 5 Nm
NOTE
Check the arrow direction on the pulley when
installing it.
(B)
24
REAR DERAILLEUR
REAR DERAILLEUR FOR ROAD

When installing, be careful that deformation is not caused by the B-tension adjust bolt coming into contact with the fork end tab.
Standard type
(A)
Install the rear derailleur.

(B) Fork end tab
Tightening torque
8 - 10 Nm
NOTE
Make sure to insert the hexagon wrench all
the way to the end of the bracket axle tool
hole when tightening.
Do not use a ball point hexagon wrench.
(B)
(C)
Ball point hexagon wrench
If tightening is performed incorrectly, the
following phenomena may result:
Deformation of the tool hole preventing

installation or removal.
Suboptimal gear shifting performance.
25
REAR DERAILLEUR
Bracket type
(A)
(B)
(C)
(D)
(A) Bracket bolt

(B) Bracket
(C) Fork end
(D) Bracket nut
Tightening torque
3 - 4 Nm
26
REAR DERAILLEUR
Stroke adjustment
Stroke adjustment
Top adjustment
(A)
Turn the top adjustment bolt to adjust so

that the guide pulley is below the outer
line of the smallest sprocket when
viewed from the rear.
(A) Outer line of smallest sprocket

(B) Guide pulley
(C) Top adjustment bolt
Turn the low adjustment bolt so that the

guide pulley moves to a position directly
in line with the largest sprocket.

(B) Guide pulley
(C) Low adjustment bolt
(B)
A
(C)
Low adjustment
(A)
(B)
A
(C)
27
REAR DERAILLEUR
Stroke adjustment
Chain length
When largest sprocket is 27T or smaller
(A)
(z) Right angle to the ground
(C)
(B)
(F)
(D)
(E)
90
(A) Smallest sprocket

(B) Chain
(D) Guide pulley
(E) Tension pulley
(F) Front double
(z)
TECH TIPS
When installing chain using, place chain in
largest chainring and smallest sprocket.
Set so that the line drawn through the guide
pulley and tension pulley is 90 or greater to
the ground.
When largest sprocket is 28T or larger

With the chain put on both the largest sprocket and the largest chainring, add 2 links to the
"minimum number of links that can be connected".
(A)
(C)
(B)
(D)
(z)
28
(z) +2 links
(B) Chain
(D) Front double
REAR DERAILLEUR
Stroke adjustment
For front triple (when largest sprocket is 30T or smaller)

(A)
(z) Right angle to the ground
(C)
(B)
(D)
(A) Smallest sprocket

(B) Chain
(D) Front triple
NOTE
90
For RD-A070, follow the adjustment method

in For front triple (when largest sprocket is
32T or larger) instead.
(z)
TECH TIPS
When installing chain using, place chain in
largest chainring and smallest sprocket.
Set so that the line drawn through the guide
pulley and tension pulley is 90 or greater to
the ground.
For front triple (when largest sprocket is 32T or larger)

(A)
(C)
(B)
(D)
With the chain put on both the largest

sprocket and the largest chainring, add
2 links to the "minimum number of links
that can be connected".
(z) +2 links

(B) Chain
(D) Front triple
(E) Pin/plate for preventing chain
derailment
(z)
TECH TIPS
(E)
(E)
29
The rear derailleur plate assembly is equipped

with a pin or plate that prevents the chain
from derailing.
When passing the chain through the rear
derailleur, pass it to the rear derailleur body
from the side of the pin/plate for preventing
chain derailment as shown in the illustration.
If the chain is not passed through the correct
position, damage may be caused to the chain
or rear derailleur.
REAR DERAILLEUR
Securing the cable
Securing the cable

Cutting the outer casing
When cutting the outer casing, cut the
end opposite to the end with the
marking.
After cutting the outer casing, make the

end round so that the inside of the hole
has a uniform diameter.
(A)
Attach the same outer cap to the cut end

of the outer casing.
(A) Outer cap
Connect the inner cable to the rear

derailleur.
(A) Groove
Connecting and securing of the cable
Tightening torque
6 - 7 Nm
(A)
Remove the initial slack from the cable

(z) Pull
2
(z)
30
REAR DERAILLEUR
Securing the cable
Reconnect the inner cable to the rear

derailleur.
(A) Groove
Tightening torque
6 - 7 Nm
NOTE
(A)
Be sure that the cable is securely in the

groove.
Groove
Using the B-tension adjust bolt

Mount the chain on the smallest
chainring and the largest sprocket, and
turn the crank arm for shifting.
(A)
(B)
(C)
A
A
B
B
Then turn the B-tension adjust bolt to

adjust so that the guide pulley does not
interfere with the sprocket but not so
close that it touches the chain.
Next, set the chain on the smallest
sprocket and repeat the above
procedure to make sure that the pulley
does not come into contact with the
sprockets.
31

REAR DERAILLEUR
SIS adjustment
SIS adjustment
Confirming positioning on gear
(z)
Operate the shifting lever several times

to move the chain to the 2nd sprocket
counting from the smallest sprocket.
Then, while operating the lever just
enough to close the gap in the lever,
turn the crank arm.
(z) Gap
The best setting is when the shifting

lever is operated just enough to close the
lever gap and the chain touches the 3rd
sprocket counting from the smallest
sprocket and makes noise.
Adjusting SIS
When the chain shifts to the 3rd sprocket from the smallest sprocket
Tighten the cable adjustment barrel until the chain returns to the 2nd sprocket counting
from the smallest sprocket. (Clockwise)
(A)
32
REAR DERAILLEUR
SIS adjustment
When no sound at all is generated

Loosen the cable adjustment barrel until the chain touches the 3rd sprocket counting from
the smallest sprocket and makes a noise. (Counterclockwise)
(A)
Return the lever to its original position (the position where the lever is at the 2nd sprocket
setting counting from the smallest sprocket and it has been released) and then turn the
crank arm clockwise.
If the chain is touching the 3rd sprocket counting from the smallest sprocket and making a
noise, turn the cable adjustment barrel clockwise slightly to tighten it until the noise stops
and the chain runs smoothly.
Stop turning at the point where the noise just stops.
Operate lever to change gears, and check that no noise occurs in any of the gear positions.
TECH TIPS
For the best SIS performance, periodically
lubricate all power-transmission parts.
33
REAR DERAILLEUR

Replace the pulley using a 3mm hexagon
wrench.

Tightening torque
2.5 - 5 Nm
(A)
34
FRONT DERAILLEUR
FRONT DERAILLEUR
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
NOTE
For
MTB/Trekking
When the chain is in the position shown in the illustration, the chain
may contact the chainrings or front derailleur and generate noise. If
the noise is a problem, shift the chain onto the next-larger sprocket
or the one after.
Figure 1
Double
Figure 2
Triple
Chainring
Sprocket
For frames with suspension, the chain stay angle will vary depending on whether the bicycle is being ridden or not.
When the bicycle is not being ridden and the chain is positioned on the largest chainring at the front and on the smallest sprocket at the rear, the
chain may come into contact with the chain guide outer plate of the front derailleur.
For
ROAD
When the chain is in the position shown in the illustration, the chain may contact
the chainrings or front derailleur and generate noise. If the noise is a problem,
shift the chain onto the next-larger sprocket or the one after.
Double
Chainring
Sprocket
36
Triple
FRONT DERAILLEUR
FRONT DERAILLEUR FOR MTB/TREKKING
Installation

NOTE
When installing components to a carbon frame/handlebar, check the tightening torque recommended by the carbon frame or component manufacturer to avoid
carbon material damage due to excessive tightening or insufficient component holding force resulting from insufficient tightening torque.
Installation
(A)
(z)
Adjust so that there is a clearance of 1 3mm

between the chain guide outer plate and the
largest chainring. (Common to all types)
(z) 1 3mm
(A) Chain guide

(B) Largest chainring
TECH TIPS
(B)
Bicycles with suspensions are positioned

differently between when a rider is off the
bicycle and on the bicycle. By referring to the
illustration, perform installation and SIS
adjustment while seated on the bicycle.
37
FRONT DERAILLEUR
Installation
Band type
When using the adapter, install it in the position shown in the illustration, relative to the
front band or the rear band.
(z) Align
(A) Adapter
(B) Front band/Rear band
(A)
(z)
(B)
When using a non-planar front band

Be sure to use a metallic adapter for a
front band which has a non-planar
shape.
(y)
(A)
(z)
(A) Front band

(B) Metallic adapter
(y) Planar shape
(B)
(z) Non-planar shape
When using a planar front band

Be sure to use a round-type plastic
adapter when using a front band with a
planar shape.
(A)
(y)
(B)
(A) Front band

(B) Round-type plastic adapter
Square-type plastic adapters are not

compatible.
(z)
(y) Planar shape

For the SM-AD16/SM-AD17

(A)
(A)
(y)
(z)
Peel off the double-sided tape from the

band adapters (front and rear are
interchangeable), and then secure the
band adapters by press-fitting them to
the fixing bands with the wider ends
oriented toward the hinge, as shown in
the illustration.
(y) Narrower
(B)
(z) Wider
38
(A) Band adapter

(B) Fixing band
NOTE
These band adapters are available in two
sizes: S size (SM-AD16S/AD17S/28.6mm
diameter) and M size (SM-AD16M/
AD17M/31.8mm diameter).
FRONT DERAILLEUR
Installation
After tentatively tightening the clamp

bolt, align the flat portion of the outer
plate of the chain guide in parallel with
the flat surface of the largest chainring.
When the adjustment is complete,
tighten the clamp bolt.
(z) 1 3mm
(A)

(C) Chain guide outer plate
Tightening torque
5 - 7 Nm
NOTE
Do not position the chain guide as shown in
the below illustrations.
(B)
(C)
(z)
(B)
39
FRONT DERAILLEUR
Installation
E-type
(A)
Align the bracket of the front derailleur

with the position of the bottom bracket
and secure it with a bolt.
(B)
(A) Front derailleur

(B) Bolt
(C) Bottom bracket position
Tightening torque
5 - 7 Nm
(C)
Insert the bottom bracket adapter as in the illustration and tighten it.
(A) Adapter
(B) Front chainwheel
Tightening torque
(B)
2
(A)
(A)
40
35 - 50 Nm
FRONT DERAILLEUR
Installation
E-type (models without BB plate)

(z) Example: When using a hexagon
Secure with bottom bracket mount fixing bolts.
wrench
Positioning varies depending on number of gear teeth.

Refer to the illustration for correct positioning.
(A) Bottom bracket mount fixing bolt

(B) Bottom bracket mount
(C) Bracket
(A)
NOTE
Shimano does not provide the bottom bracket
mount fixing bolts.
(B)
(C)
(z)
Securing position
(y)
(y) Double:
(z)
Largest chainring 38T

Triple:
(z) Double:
Triple:
41
FRONT DERAILLEUR
Installation
Direct mount type

Adjust the height of the front derailleur.
(A) Chainwheel
The flat section of the chain guide outer plate should be directly above and parallel to the
largest chainring.
(B) Chain guide

(C) 5mm hexagon wrench
(largest chainring)
Secure with a hexagon wrench (5mm).

Tightening torque
5 - 7 Nm
(A)
(C)
(B)
The mounting height varies depending on the position of the base on the frame.
[1] 155.5mm
(From bottom bracket center)
(x)
(y)
(z)
(x) Double: 42T

(y) Double: 40T
Triple: 42T
(z) Double: 38T

[2] 159.5mm
(From bottom bracket center)
(x) Double: 44T

(y) Double: 42T
(z) Double: 40T
Triple: 42T
[1]
[2]
42
FRONT DERAILLEUR
Fixing the cable and adjusting the SIS (Front double)

Low adjustment
(A)
Set the chain on the smallest chainring

at the front and the largest sprocket at
the rear.
(A) Smallest chainring

(B) Largest sprocket
(x) Low
(x)
(y)
(y) Top
(z) Cable index point
(z)
(B)
Set so that the clearance between the

chain guide inner plate and the chain is
0 0.5mm.
(x) Top swing
(x)
(y) Down swing

(z) 0 0.5mm
(y)
(A)
(B)
(z)
43
(A) Chain guide inner plate

(B) Chain
FRONT DERAILLEUR
Securing the cable

Use the shifting lever with a mode converter in x2 mode. To shift from x3 to x2, refer to the maintenance section of the dealers manual for the shifting
lever RAPIDFIRE Plus.
Top Swing (Common to E-type and band type)

Down pull
Use a spanner or a hexagon wrench to

tighten the wire mounting bolt.
(A) 5mm hexagon wrench/

9mm spanner
Tightening torque
5 - 7 Nm
NOTE
Run the cable through as shown in the
illustration.
(A)
Wire mounting bolt
Top pull
(A)
44
FRONT DERAILLEUR
Down swing (Band type)

Down pull
Use a hexagon wrench to tighten the

wire mounting bolt.
Tightening torque
5 - 7 Nm
NOTE
illustration.
Wire mounting bolt
Different shaped type

Wire mounting bolt
Top pull

wire mounting bolt.
Tightening torque
5 - 7 Nm
45
FRONT DERAILLEUR
Down swing (Direct mount type)

Down pull
Tightening torque

wire mounting bolt.
5 - 7 Nm
NOTE
illustration.
Wire mounting bolt
Different shaped type

Wire mounting bolt
1
Top pull
Tightening torque

wire mounting bolt.
5 - 7 Nm
After taking up the initial slack in the cable, re-secure to the front derailleur as shown in the
illustration.
Down pull
Top pull
(z)
2
(z)
46
(z) Pull
FRONT DERAILLEUR
Adjustment of the cable tension

(A)
Set the chain onto the largest chainring

and the largest sprocket.
(A) Largest chainring

(x) Low
(y) Top
(x)
(y)
(z)
(B)

0 0.5mm.
(z)
(z) 0 0.5mm
(D)
(C)
(A)
(B)
47

(B) Chain
(C) Cable adjustment barrel
(D) Cable adjuster
FRONT DERAILLEUR
Top adjustment
Set the chain on the largest chainring at
the front and the smallest sprocket at
the rear.
(A)

(x) Low
(x)
(y) Top
(y)

(z)
(B)

chain guide outer plate and the chain is
0 0.5mm.
(z)
(A) Chain guide outer plate

(B) Chain
(x) Top swing

(y) Down swing
(z) 0 0.5mm
2
(x)
(A)
(B)
(y)
Troubleshooting chart
After low adjustment, fixing the cable, cable tension adjustment and top adjustment, operate the shifting lever to check the shifting.
(This also applies if shifting becomes difficult during use.)
* Turn the bolt by 1/8th turn for each adjustment.
If the chain falls to the crank side.
Turn the top adjustment bolt clockwise.
If shifting is difficult from the smallest chainring to the largest

chainring.
Tighten the cable. If this does not improve the situation, turn the top
adjustment bolt counterclockwise.
If shifting is difficult from the largest chainring to the smallest

chainring.
Turn the low adjustment bolt counterclockwise.
If the chain falls to the bottom bracket side.
Turn the low adjustment bolt clockwise.
48
FRONT DERAILLEUR
Fixing the cable and adjusting the SIS (Front triple)

Low adjustment
Remove the Pro-Set alignment block.
(A) Pro-Set alignment block

the rear.

(A)
(A)
(w) Low
(w)
(x)
(y)
(x) Middle
(y) Top
(z)

(B)

0 0.5mm.
(x) Top swing
(x)
(y) Down swing

(z) 0 0.5mm
(y)
(A)
(B)
(z)
49

(B) Chain
FRONT DERAILLEUR
Securing the cable

Use the shifting lever with a mode converter in x3 mode. To shift from x2 to x3, refer to the maintenance section of the dealers manual for the shifting
lever RAPIDFIRE Plus.
TECH TIPS
The cable can be secured on each FD type in the same way as the double. Refer to Fixing the cable and adjusting the SIS (Front double).
Top adjustment
the rear.
(A)

(w) Low
(w)
(x)
(y)
(x) Middle
(y) Top
(z)
(B)

0 0.5mm.
(z)
(x) Top swing

(y) Down swing
(z) 0 0.5mm
2
(x)
(A)
(B)
(y)
50

(B) Chain
FRONT DERAILLEUR

(A)
Set the chain onto the middle chainring

(A) Middle chainring

(w) Low
(w)
(x)
(y)
(y) Top
(z)
NOTE
(x) Middle
Adjust the lever after operating it from top to

middle, not low to middle.
(B)
Low
Middle
Cable index point

0 0.5mm.
(z) 0 0.5mm
(z)
(D)
(C)
(A)
(B)
51

(B) Chain
(D) Cable adjuster
Top
FRONT DERAILLEUR
If shifting is difficult from the middle chainring to the largest chainring.
If shifting is difficult from the largest chainring to the middle chainring.
Loosen the cable.
If the middle chainring is skipped when shifting from the largest

chainring.
Tighten the cable.
If shifting is difficult from the middle chainring to the smallest

chainring.
52
FRONT DERAILLEUR
FRONT DERAILLEUR FOR ROAD
Installation

NOTE
Installation
When using the adapter, install it in the position shown in the illustration, relative to the
front band or the rear band.
(z) Align
(A) Adapter
(B) Front band/Rear band
(A)
(z)
(B)
When using a non-planar front band

Be sure to use a metallic adapter for a
front band which has a non-planar
shape.
(y)
(A)
(z)
(y) Planar shape
(B)
Adjust so that there is a clearance of

1 3mm between the chain guide outer
plate and the largest chainring.
(A)
(z)
(A) Front band

(B) Metallic adapter
(B)
After tentatively tightening the clamp

bolt, align the flat portion of the outer
plate of the chain guide in parallel with
the flat surface of the largest chainring.
(z) 1 3mm
53

NOTE
Do not position the chain guide as shown in
the below illustrations.
FRONT DERAILLEUR
Installation
When the adjustment is complete,

tighten the clamp bolt.

9mm spanner
Tightening torque
(A)
5 - 7 Nm
54
FRONT DERAILLEUR

Lever operation and cable index point
Front shifting (Standard type)
(t) From largest chainring to smallest
When the lever [a] is operated
(v)
(w)
(x)
(B)
(A)
(y)
(B)
(t)
chainring
(u) From smallest chainring to largest

chainring
(z)
(A)
(u)
(v) Low
(w) Top
(x) L-trim
(y) T-trim
(A) Lever [a]
(B) Lever [b]
Font shifting (Thumb release type)

(t) From largest chainring to smallest
When the lever [b] is operated
chainring
(B)
(t)
(v)
(w)
(x)
(y)
chainring
(v) Low
(z)
(A)
(u) From smallest chainring to largest
(w) Top
(x) L-trim
(A)
(u)
(y) T-trim
(A) Lever [a]
(B) Lever [b]
55
FRONT DERAILLEUR
Securing the cable
Check that the lever [b] is released to the low position by operating it 2 or more times
before fixing the inner cable.
After fixing the cable, remove the initial

extension from the cable as shown in the
illustration.
After that, fix the cable again on the
front derailleur.
(z) Pull
(z)
56
Tightening torque
6 - 7 Nm
FRONT DERAILLEUR
Low adjustment
(A)

the rear.

(w) Low
(x) Top
(w)
(x)
(y)
(z)
(y) L-trim
(z) T-trim
(B)

0 0.5mm.
(z) 0 0.5mm
(A)
(B)
(z)
57

(B) Chain
FRONT DERAILLEUR

(A)
Set the chain onto the largest chainring


(w) Low
(x) Top
(w)
(x)
(y)
(z)
(y) L-trim
(z) T-trim
(B)

0 0.5mm.
(z)
(z) 0 0.5mm
(C)
(D)
(A)
(B)
58

(B) Chain
(D) Cable adjuster
FRONT DERAILLEUR
Top adjustment
the rear.
(A)

(w) Low
(x) Top
(w)
(y) L-trim
(x)
(y)
(z) T-trim
(z)
(B)

0 0.5mm.
(z)

(B) Chain
(z) 0 0.5mm
(B)
(A)
If shifting is difficult from the smallest chainring to the largest

chainring.
If shifting is difficult from the largest chainring to the smallest

chainring.
59
FRONT DERAILLEUR

Lever operation and cable index point
Front shifting (Standard type)
(r) From largest chainring to smallest
When the lever [a] is operated
chainring
(t)
(u)
(w)
(B)
(A)
(v)
(x)
(B)
(r)
(s) From smallest chainring to largest

chainring
(y)
(z)
(A)
(s)
(t) Low
(u) Middle
(v) Top
(w) L-trim
(x) M-trim
(y) T-trim
(A) Lever [a]
(B) Lever [b]
Front shifting (Thumb release type)

(r) From largest chainring to smallest
When the lever [b] is operated
chainring
(B)
(r)
(t)
(u)
(w)
(x)
(y)
(s) From smallest chainring to largest

chainring
(t) Low
(z)
(A)
(v)
(u) Middle
(v) Top
(A)
(s)
(w) L-trim
(x) M-trim
(y) T-trim
(A) Lever [a]
(B) Lever [b]
60
FRONT DERAILLEUR
Low adjustment
Remove the Pro-Set alignment block.
(A) Pro-Set alignment block

the rear.

(A)
(A)
(t) Low
(u) Middle
(v) Top
(w) L-trim
(x) M-trim
(B)
(t)
(y) T-trim
(u)
(w)
(v)
(x)
(y)
(z)

0 0.5mm.
(z) 0 0.5mm
(A)
(B)
(z)
61

(B) Chain
FRONT DERAILLEUR
Securing the cable
Check that the lever [b] is released to the low position by operating it 3 or more times
before fixing the inner cable.
After fixing the cable, remove the initial

extension from the cable as shown in the
illustration.
After that, fix the cable again on the
front derailleur.
(z) Pull
(z)
62
Tightening torque
6 - 7 Nm
FRONT DERAILLEUR
Top adjustment
the rear.
(A)

(t) Low
(u) Middle
(v) Top
(w) L-trim
(x) M-trim
(B)
(t)
(y) T-trim
(u)
(w)
(v)
(x)
(y)
(z)

0 0.5mm.
(z)
(z) 0 0.5mm
(B)
(A)
63

(B) Chain
FRONT DERAILLEUR

Set the chain onto the middle chainring
(A)
(A) Middle chainring

(t) Low
NOTE
(u) Middle
Adjust the lever after operating it from top to

middle, not low to middle.
(v) Top
(w) L-trim
Low
(x) M-trim
(B)
(t)
(y) T-trim
(u)
(w)
(v)
(x)
Middle
Top
L-trim
M-trim
T-trim
Cable index point
(y)
(z)

0 0.5mm.
(z) 0 0.5mm
(z)
(D)
(C)
(A)
(B)
64

(B) Chain
(D) Cable adjuster
FRONT DERAILLEUR
If shifting is difficult from the middle chainring to the largest chainring.
If shifting is difficult from the largest chainring to the middle chainring.
Loosen the cable.
If the middle chainring is skipped when shifting from the largest

chainring.
Tighten the cable.
If shifting is difficult from the middle chainring to the smallest

chainring.
65
FRONT DERAILLEUR
MAINTENANCE
MAINTENANCE
If shifting operation becomes less smooth, clean the front derailleur and lubricate the link sections shown in the illustration.
Brazed-on type
E-type
(A) Links
(A)
(A)
(A)
Band type
Direct mount type
(A)
(A)
(A)
66
CHAIN
CHAIN
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
Intervals between maintenance depend on the use and riding circumstances. Clean the chain and QUICK-LINKs regularly with an appropriate chain
cleaner. Never use alkali based or acid based solvents, such as rust cleaners. If any of these are used, the chain or QUICK-LINK might break resulting in
serious injury.
In order to obtain good gear shifting performance, CN-HG900-11/HG700-11/HG600-11, CN-M981/HG95/HG75/HG54, CN-7901/6701/5701/4601,
CN-E6090-10 have a forward side and a reverse side, and the sides are marked so that the chain will face the correct way when installed. For best
chain performance make sure it is installed to face the correct way. If it is installed so that it faces the opposite way, the chain may come off and the
bicycle may fall over and serious injury may occur as a result.
Check the chain and QUICK-LINK for any damage (deformations or cracks), chain skipping, or other abnormalities such as unintended gear shifting. If
any problems are found, consult a dealer or an agency. There is a risk of the chain breaking or the QUICK-LINK disengaging, which may cause the
bicycle to collapse.
Only use the tool and connecting pin models specified in the table to connect the chain. If unsuitable connecting pins or tools are used to connect the
chain, the connecting pin force may not be sufficient, which could cause the chain to break or fall off. If using a QUICK-LINK to connect the chain,
refer to the section "QUICK-LINK".
Chain
Reinforced connecting pin / QUICK-LINK
11-speed
CN-9000/6800
CN-HG900-11/HG700-11/HG600-11
TL-CN34
TL-CN28
5.8mm
TL-CN10
All 11-speed chains

For MTB/Trekking/E-BIKE
10-speed super narrow chain
CN-M981/HG95/HG75/HG54/E6090-10 etc.
(CN-M980/HG94/HG74 EOL)
For ROAD double crank
CN-7901/6701/5701/4601 etc.
Tool
with groove [2]

5.85mm
with groove [3]
For ROAD triple crank

CN-7801/6600/5600 etc.
TL-CN34
TL-CN33
5.85mm
TL-CN32
TL-CN28
Silver

CN-YM81/7701/HG93/E6070-9 etc.
6.5mm
Black
8/7/6-speed narrow chain

CN-HG50/HG40 etc.
7.1mm
68
TL-CN27
CHAIN
TO ENSURE SAFETY
If it is necessary to adjust the length of the chain due to a change in the number of sprocket teeth,
make the cut in a place other than where the chain has been joined using a reinforced connecting pin.
The chain will be damaged if it is cut at a place where it is joined with a reinforced connecting pin.
Reinforced connecting pin
Link pin
When readjusting the length of the chain, be sure to insert the reinforced connecting pin from the same side as the chain cutter was inserted (the
same direction as when the chain was cut).
11/10-speed
chain (ampoule pin type)

After adjustment, make sure that the connecting pin is as shown in the illustration by running your finger over it. (The pin will protrude slightly after
the break off pin is removed)
Link surface
Slightly protruding
Link surface
Connecting pin
Connecting pin
9/8/7/6-speed
chain
Be sure to check that the connecting pin protrudes equally from both sides of the chain after it has been joined.
Should be uniform
Connection location
69
CHAIN
TO ENSURE SAFETY
NOTE
CN-E6090-10/CN-E6070-9 can be used only in combination with single front chainrings.
As illustrated in Fig. [A], we strongly recommend to set the connecting pin in the hole of the outer link on the front side in the direction of travel.
The chains level of strength is enhanced compared to the method in Fig. [B].
[A]
Inner link
Rotation of the crank
Outer link
Connecting pin
[B]
Inner link
Outer link
Connecting pin
You should periodically wash the chainrings/sprockets in a neutral detergent and then lubricate them again. In addition, cleaning the chain and
QUICK-LINKs with neutral detergent and lubricating them can be an effective way of extending their useful life.
For
CN-HG900-11/HG700-11/HG600-11, CN-M981/HG95/HG75/HG54, CN-7901/6701/5701/4601, CN-E6090-10
In order to achieve good gear shifting performance, these have a forward side and a reverse side and must be fitted in the correct orientation.
* The side with the mark shown in the illustration is the forward side (outer side).
Forward (outer side)
CN-M981/HG95/HG75/HG54/E6090-10
(CN-M980/HG94/HG74 EOL)
CN-HG900-11/HG700-11/HG600-11
CN-7901/6701/5701/4601
70
Reverse (inner side)
CHAIN
CHAIN CONNECTING PIN
Method of use
CHAIN CONNECTING PIN

Method of use
Insert the connecting pin.
(A)
Press in the connecting pin using a chain

tool.
(A) Chain tool
Break off the excess portion of the

connecting pin.
71
NOTE
Set the chain on the chain cutting tool as
shown in the illustration when using the chain
cutting tool. If the tool is used with the chain
set incorrectly, the positioning plate will get
damaged.
CHAIN
QUICK-LINK
QUICK-LINK
WARNING
Do not reuse QUICK-LINKs that have been removed. If you reuse them, the QUICK-LINKs may break and you may fall.
Intervals between maintenance depend on the use and riding circumstances. Clean the chain and QUICK-LINKs regularly with an appropriate chain
cleaner. Never use alkali based or acid based solvents, such as rust cleaners. If any of these are used, the chain or QUICK-LINK might break resulting in
serious injury.
If it is necessary to adjust the length of the chain due to a change in the number of sprocket teeth, make the cut at some other place than the place
where the chain has been joined using a QUICK-LINK. The chain cutter will be damaged if the chain is cut at a place where it has been joined with a
QUICK-LINK.
Check the chain and QUICK-LINK for any damage (deformations or cracks), chain skipping, or other abnormalities such as unintended gear shifting. If
any problems are found, consult a dealer or an agency. There is a risk of the chain breaking or the QUICK-LINK disengaging, which may cause the
bicycle to collapse.
When replacing the chain with a new one, be sure to also replace the QUICK-LINK with a new one. If you do not replace it, the QUICK-LINK may break
and you may fall.
When attaching the QUICK-LINK, make sure that the pins on the link plates are pushed all the way in and securely planted in the link holes.
Be sure to follow the instructions provided in the manuals when installing the product.
It is recommended to use genuine Shimano parts only. If adjustments are not carried out correctly, the chain may come off and this may cause you to
fall off the bicycle which could result in serious injury.
QUICK-LINK
compatible chains
Model No.
QUICK-LINK
Compatible chains
SM-UG51
All 6, 7, and 8-speed chains
SM-CN900-11
All 11-speed chains
When attaching SM-CN900-11, be sure to attach it so that the arrow on the surface faces in the direction of rotation of the crank when viewed from
the front.
If not attached correctly, SM-CN900-11 could detach causing the bicycle to collapse.
QUICK-LINK
Arrow
Crank
Read these instructions carefully, and keep them in a safe place for later reference.
NOTE
You should periodically wash the chainrings/sprockets in a neutral detergent and then lubricate them again. In addition, cleaning the chain and
QUICK-LINKs with neutral detergent and lubricating them can be an effective way of extending their useful life.
Shimano original tool is required to remove the QUICK-LINK. Consult a dealer or an agency.
72
CHAIN
QUICK-LINK
Installing QUICK-LINKs (SM-UG51)

Remove the outer link at the connection
location so that both ends of the chain
finish at an inner link.
(A) Inner link
Insert the connecting link with pins

section of the QUICK-LINK as shown in
the illustration.
(A) Connecting link with pins

(B) Inner link
Place the connecting link with hole onto

one of the pins, and then slide the
connecting link so that the pin is at the
other end from the hole.
(The side of the link plate with the
depression should be facing toward the
outside at this time.)
(A) Hole
(B) Connecting link with hole
1
(A)
(A)
2
(B)
(B)
(A)
(z) Depression should be on the

(z)
outside
Turn the connecting link with hole until

it overlaps the other pin.
4
(A)
73
(A) Hole
CHAIN
QUICK-LINK
Loosen the chain and insert the pin

securely into the hole.
[1]
(A)
There should be no gap between the

connecting link with pins and the inner
link [1].
(B)
Insert the pins into the hole while

pushing the connecting link with hole
[2].
[2]
Set both pins securely into the slot of the

connecting link with hole, and check
that both plates are parallel.
(z)
(z) Parallel
74
(A) Inner link

(B) Connecting link with pins
CHAIN
QUICK-LINK
Installing QUICK-LINKs (SM-CN900-11)
Installing QUICK-LINKs (SM-CN900-11)

Insert the pins of the QUICK-LINKs into
the spaces in the inner link from both
sides as shown in the illustration.
(z)
(A)
(A) Crank
(B) Arrow
(C) QUICK-LINK
When using SM-CN900-11, be sure to

install it so that the arrow on the surface
faces in the direction of rotation of the
crank when viewed from the front.
(z) Rotation of the crank
(B) (C)
Use Shimano original tool TL-CN10 to

slide the pins and insert them firmly.
NOTE
Check that both QUICK-LINKs are firmly
fastened in position as shown in the
illustration.
TECH TIPS
It is also possible to secure the chain link

without using a tool by turning the crank
while applying the brake. In this case too,
check that the pins slide securely into place.
[1]
[2]
75
CHAIN
QUICK-LINK
Removing QUICK-LINKs (SM-CN900-11)
Removing QUICK-LINKs (SM-CN900-11)

Set Shimano original tool TL-CN10 as
shown in the illustration, slide the pins
and remove the QUICK-LINK.
CT
VE CON
NE
MO
RE
76
BRAKE
BRAKE
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
For
Disc Brake
If the disc brake rotor is cracked or warped, be sure to replace it with a new disc brake rotor.
If the disc brake rotor becomes worn down to a thickness of 1.5mm or so that the aluminum surface becomes visible, be sure to replace the disc brake
rotor with a new one.
If any oil or grease gets on the pads, replace the pads. If any oil or grease gets on the disc brake rotor, wipe clean the disc brake rotor. Otherwise, the
brakes may not work correctly.
For
Hydraulic Disc Brake
Use only Shimano genuine mineral oil. If other types of oil are used, it may cause problems with brake operation, and cause the system to be unusable.
Be sure to use only oil from a freshly-opened container. Do not re-use oil which has been drained from the bleed nipple. Old or reused oil may contain
water, which could cause vapor lock in the brake system.
Be careful not to let water or air bubbles get into the brake system. Otherwise vapor locks may occur. Be particularly careful when removing the bleed
screws.
If cutting the brake hose in order to adjust the length of the hose, or when changing over the brake hose from left to right or vice versa, be sure to
bleed the air from the hose by carrying out steps (4), (8) to (12) given in Adding mineral oil and bleeding air.
The disc brake is not designed to work when the bicycle is upside down. If the bicycle is turned upside down or on its side, the brake may not work
correctly, and a serious accident could occur. Before riding the bicycle, be sure to operate the brake lever a few times to check that the brakes operate
normally. If the brakes do not operate normally, stop using the brakes and consult a dealer or an agency.
If brake operation is sluggish when the lever is depressed
Gently depress the brake lever several times and wait for the bubbles to return to the reservoir tank. It is recommended that you then remove the
bleed screws and fill the reservoir tank with mineral oil until no air bubbles remain.
If the brakes are still sluggish, bleed the air from the brake system. (Refer to Adding mineral oil and bleeding air.)
If the quick release lever is on the same side as the disc brake rotor, there is the danger that it may interfere with the disc brake rotor, so check that it
does not interfere.
Shimano disc brake systems are not compatible with tandem bicycles. Because tandem bicycles are heavier, the stress on the brake system increases
during brake operation. If hydraulic disc brakes are used with tandem bicycles, the oil temperature will become too high and vapor locks or ruptures
in the brake hoses may occur, causing the brakes to fail.
If fluid leaks occur, immediately stop using the brakes and carry out the appropriate repairs. If you continue riding the bicycle while fluid is leaking,
there is the danger that the brakes may suddenly stop working.
78
BRAKE
TO ENSURE SAFETY
For
Mechanical Disc Brake
Adjust the inner cable so that the protruding length is less than 20mm (3/4 inch). If the protruding length is any
longer, the end of the inner cable may become stuck in the disc brake rotor, which could cause the wheel to lock
and the bicycle could fall forward causing serious injuries.
20mm or less
Be careful not to allow any oil or grease to get onto the disc brake rotor and brake pads. Otherwise the brakes may not work correctly.
For
V-BRAKE/Caliper Brake
Brakes designed for use as rear brakes should not be used as front brakes.
Be careful not to allow any oil or grease to get onto the brake shoes. If any oil or grease do get on the shoes, you should replace the shoes. Otherwise
the brakes may not work correctly.
For
caliper brakes
Securely tighten the caliper brake mounting nuts to the specified tightening torque.
Use lock nuts with nylon inserts (self-locking nuts) for nut-type brakes.
For sunken nut type brakes, use sunken nuts of the appropriate length which can be turned six times or more. When re-installing, apply sealant
(locking adhesive) to the nut threads.
If the nuts become loose and the brakes fall off, they may get caught up in the bicycle and the bicycle may fall over.
Particularly if this happens with the front wheel, the bicycle may be thrown forward and serious injury could result.
Check the brake cable for rust and fraying, and replace the cable immediately if any such problems are found. Otherwise, the brakes may not work
correctly.
79
BRAKE
TO ENSURE SAFETY
For
cantilever brakes
Brake handling may vary slightly by model. Therefore, be sure to learn the proper braking technique (including brake lever pressure and bicycle
control characteristics) and operation of your bicycle.
Improper use of your bicycles brake system may result in loss of control or an accident, which could also lead to severe injury. For proper operation,
consult a professional bicycle dealer or the bicycle's owner's manual.
It is also important to practice riding and braking, etc.
For the unit link type of cantilever brake, the brake performance that the brake was designed to
produce can be obtained if the mark in the center of the cable carrier is directly in line with the link
wire.
However, if the cable is bent with excessive force, it will hinder the smooth transmission of braking
force, or it might make the cable rub against the frame or cause sharp bends in the cable, which will in
turn cause the cable to break easily.
In addition, if the unit link is forcibly set to the condition shown in the illustration, sufficient braking
force will not be obtained and excessive force will be applied at points [A] and [B], which will also cause
the cable to break easily.
Unit link is curved
Link wire
[B]
[A]
Accordingly, always make sure that the mark in the center of the cable carrier is directly in line with the
link wire as shown in the illustration when the brake cable is being installed.
Mark and link wire should be

directly in line
Mark
Link wire
CAUTION
For
Resin pads are designed to reduce the amount of noise generated between the pads and the disc brake rotor when the brakes are operated. A longer
run-in period is required than for metal pads.
Handling the mineral oil
Use safety glasses when handling, and avoid contact with eyes. Contact with eyes may result in irritation. In the event of eye contact, flush with fresh
water and seek medical assistance immediately.
Use gloves when handling. Contact with skin may cause a rash and discomfort.
In the event of contact with skin, wash well with soap and water.
Inhalation of oil mist or vapors may cause nausea. Cover nose and mouth with a respirator type mask and use in a well ventilated area. If mist or vapor
is inhaled, go immediately to an area with fresh air, cover up with a blanket, stay warm and stable and seek professional medical advice.
Do not drink. May cause vomiting or diarrhea.
Keep out of reach of children.
Do not cut, let near heat, weld or pressurize the oil container, as this may cause explosion or fire.
Disposal of Used Oil : Follow local county and/or state codes for disposal. Use caution when preparing the oil for disposal.
Directions: Keep the container sealed to prevent foreign objects and moisture from getting inside, and store it in a cool, dark area away from direct
sunlight or heat.
80
BRAKE
TO ENSURE SAFETY
For
V-BRAKE brakes
The power modulator is a device that makes it easier to control braking by increasing the brake lever's cable stroke within a certain range of braking
force.
If the effective operating range of the power modulator is exceeded, the lever stroke and the brake will operate as V-BRAKE (responsive and
powerful). In that case, the brakes may operate more powerfully than intended and may cause the wheel to lock up. Therefore it is essential that you
fully understand and test the performance of the power modulator before use.
The power modulator is not equipped with a function to prevent the wheel from locking up.
Braking Performance Comparison
(kg)
Braking force at wheel
w/o power modulator
Effective operating range of

the power modulator
w/ power modulator
Cable stroke at brake lever
NOTE
For
If the brake lever is depressed without the pad spacers installed, the pistons will protrude further than is normal. Use a flat-shaped tool to push back
the brake pads, while being careful not to damage the surfaces of the brake pads.
(If the brake pads are not installed, use a flat-shaped tool to push the pistons straight back in, while being careful not to damage them.)
If it is difficult to push the brake pads or pistons back, remove the bleed screws and then try again. (Note that some oil may overflow from the
reservoir tank at this time.)
Use isopropyl alcohol, soapy water or a dry cloth when cleaning and carrying out maintenance of the brake system. Do not use commercially-available
brake cleansers or silencing agents, as they can cause damage to parts such as seals.
Do not remove the pistons when disassembling the calipers.
For
Mechanical Disc Brake
If the brake caliper mounting boss and the fork end are not parallel, the disc brake rotor and caliper may touch.
For
V-BRAKE brakes
The Multi-Condition Brake System can reach maximum efficiency if the brakes and brake levers are used in the recommended combinations.
If the brake shoes have worn down to where the grooves are no longer visible, they should be replaced.
81
BRAKE
DISC BRAKE
Wheel spoke lacing
DISC BRAKE
Wheel spoke lacing
Rotating direction of wheel
(w)
(x)
(y)
Check that the spokes have been laced

(z)
(w) Front left

(x) Rear left
(y) Rear right
NOTE
A radial assembly cannot be used.
Refer to [1] for spoke arrangement of the left
side of the front wheel (disc brake rotor
mounted side) and both sides of the rear
wheel; refer to [2] for spoke arrangement of
the right side of the front wheel.
(z) Front right
[1]
[2]
Installation of the disc brake rotor

Center lock type
(A) Rotor fixing lock ring
(B) Lock ring tightening tool
Tightening torque
(A)
(B)
40 - 50 Nm
Internally serrated type
Internally and
externally serrated
type
Externally serrated
type
Rotor fixing lock

ring
Lock ring
tightening tool
TL-LR15
Adjustable wrench
TL-FC36/TL-LR11
TL-FC36
Adjustable wrench
82
BRAKE
DISC BRAKE
5 bolt type (with lock washers)

Attach the disc brake rotor and the disc
brake rotor lock washers to the hub, and
then tighten them on with a bolts.
(A)
(A) Lock washer

(B) Disc brake rotor fixing bolt
Tightening torque
2 - 4 Nm
NOTE
Fit the lock washers so that the marking
"TOP" is visible.
Ensure that the hooked parts of the lock
washer are securely caught on the notches

in the disc brake rotor and then tighten on
the lock washer with the disc brake rotor
fixing bolt. If tightened while the hooked
parts are against the surface of the disc
brake rotor, the washer and its hooked
parts will become deformed.
(B)
Notch in disc brake rotor

Hooked part of washer
The lock washers are not reusable.

Always use new lock washers when
installing/re-installing the disc brake
rotor.
Use the dedicated disc brake rotor
fixing bolts.
Wear gloves and turn the disc brake

rotor clockwise with some force.
At this time, tighten on the disc brake

rotor fixing bolts in the order indicated
in the illustration.
83
BRAKE
DISC BRAKE
6 bolt type
Install the disc brake rotor and the disc
brake rotor tightening plate to the hub,
and then install and tighten the bolts.
(A)
(B)
(C)
(D)
(A) Hub
(B) Tightening plate
(C) Disc brake rotor
(D) Rotor fixing bolt
Tightening torque
2 - 4 Nm

While doing this, tighten the rotor fixing
bolts in the order shown in the
illustration.
(A)
Use a slotted screwdriver or similar tool

to bend the edges of the tightening
plate over the heads of the bolts.
84
(A) Tightening plate
BRAKE
DISC BRAKE
6 bolt type (with lock washers)

Install the disc brake rotor and rotor lock
washers to the hub and tighten the
bolts.
(A) Lock washer

(B) Rotor fixing bolt
Tightening torque
2 - 4 Nm
NOTE
Fit the lock washers so that the marking
(B)
"TOP" is visible.
(A)
The lock washers are not reusable. Always

use new lock washers when installing/
re-installing the disc brake rotor.
Use the dedicated rotor fixing bolts.

While doing this, tighten the rotor fixing

bolts in the order shown in the
illustration.
85
BRAKE
INSTALLATION (HYDRAULIC DISC BRAKES)
Installation of the brake lever

NOTE
Secure the brake lever as shown in the

illustration.
(A)

5mm hexagon wrench
Tightening torque
6 - 8 Nm
BL-M987/BL-M9000/BL-M9020
Tightening torque
4 - 6 Nm
NOTE
Check that the brake lever does not interfere
with the shifting lever during operation.
Some types might require the shifting lever to
be installed first, due to the position of the
shifting lever fixing bolts.
86
BRAKE
For open clamp band type

Use a 2mm hexagon wrench to open the
clamp band of the brake lever as shown
(A)
(A) Clamp band

(z) Push
NOTE
For models with the clamp band lock release
hole on the outer side of the bracket body
When installing the brake lever, be sure to

use a spacer.
[2]
The spacer should only be removed when

combining with an I-Spec II type shifting
lever. For information on the combining
procedure, refer to Shifting lever
RAPIDFIRE Plus 11-speed in the dealers
manual.
[1]
(B)
(z)
Lock release hole
[1]
[2]
Spacer
4mm hexagon wrench/5mm hexagon wrench
87
BRAKE
Installation of the brake hose

Use a utility knife or similar tool to cut
the hose.
90
(A) Utility knife

NOTE
Use the utility knife safely and correctly in
accordance with its instruction manual.
If you are using TL-BH62, refer to the
manual accompanying the product.
(A)
(A)
(B)
Pass the brake hose through the

connecting bolt and the olive as shown
(C)
(w)
(x)
(w) Direction of insertion

(x) Cut end
(y) Grease the outside of the olive.
(y)
(C)
(D)
(z) Attach the cover to the

connecting bolt for the brake
lever.
(E)
(z)
88
(A) Hose
(B) Connecting bolt
(C) Olive
(D) Premium grease
(E) Cover
BRAKE
In order to check that the end of the brake hose are fitted securely into the base of the hose
mounts of the calipers and brake lever, make marks on the hose beforehand as shown in the
illustration.
At brake lever end
At caliper end
(y)
(y)
(y)
(y) Mark
(z) Length
TECH TIPS
(y)
As a guide, the length of hose inside the

mounts should be approximately 11 or 14mm,
measured from the cut end of the hose.
(z)
(z)
Model No.
Length
Type
Model No.
Length
Type
SM-BH90-SB
SM-BH90-SS
SM-BH59-JK-SS
SM-BH80
11mm
11mm*
11mm*
14mm
Banjo type
Straight type
Straight type
Banjo type
SM-BH90-SS
SM-BH59-JK-SS
11mm*
11mm*
Banjo type
Straight type
* 14mm for BR-T675/T615/M446.
* 14mm for BL-T675/T615/M445/T445.
Use an object such as a needle to smooth

the inside of the cut end of the hose,
and then install the connector insert.
(B)
Attach the hose to the TL-BH61, as

shown in the illustration, and secure the
TL-BH61 in a vise.
(A)
(A)
(B)
(C)
(D)
(z)
(E)
Then use a hammer or similar tool to

knock the connector insert in firmly until
the base of the connector insert touches
the end of the hose.
NOTE
If there is a marking as shown in the
illustration, refer to the section Replacing
the brake hose (easy hose joint system).
If the end of the hose is not touching the

base of the connector insert, the hose
may become disconnected or fluid leaks
may occur.
(z) SM-BH90: 1mm

SM-BH59/BH80
(YM-BH81): 4mm
(A) Connector insert

(B) Hose
(C) Olive
(D) TL-BH61
(E) Vise
89
Mark
BRAKE
(z)
(A)
(B) (C)
After checking that the olive is

positioned as shown in the illustration,
apply premium grease to the threads of
the connecting bolts and attach the hose
to the brake lever as shown in the
illustration.
(A) Hose
(B) Olive
(C) Connector insert
(z) SM-BH90: 2mm

SM-BH59/BH80
(YM-BH81): 5mm
Model No.
Length
Color
SM-BH90
11.2mm
Silver
SM-BH59/80
13.2mm
Gold
YM-BH81
13.2mm
Silver
Left lever
Make sure that the brake hose is not

twisted.
Make sure that the calipers and levers
are in the positions shown in the
illustrations.
Right lever
(A)
While pushing the brake hose, tighten

the connecting bolt.
(A) 8mm spanner

(B) Connecting bolt
Tightening torque
5 - 7 Nm
(B)
90
BRAKE
At caliper end (Banjo type)
(B)
(A)
After checking that both O-rings are

fitted in the top groove and bottom
groove of the banjo, secure the banjo to
the caliper as shown in the illustration.
At this point, check that the O-rings are
in the grooves.
The O-rings are greased.
(D)
(C)
(A) Banjo
(B) Hose
(C) O-ring
(D) 3mm hexagon wrench/
4mm hexagon wrench
For 3mm hexagon wrench
Tightening torque
5 - 7 Nm
For 4mm hexagon wrench
Tightening torque
8 - 10 Nm
At caliper end (Straight type)

(A) Olive
(B) Connecting bolt
(C) Caliper
(A)
Tightening torque
5 - 7 Nm
(B)
(C)
91
BRAKE
Installation of the brake hose (easy hose joint system)

This procedure for installation of the brake hose is directed at bicycle OEMs.
Overview of the easy hose joint system (For MTB)
(B)
(A)
(A) Brake caliper

(B) Hose cap
(C) Brake hose connection port
(D) Lever stopper
(E) Brake lever
(D)
(C)
(E)
Pass the brake hose through each hole in the built-in frame.
Remove the hose cap.
Secure the brake lever in a vise or

another similar device.
Face the hose connection port upward
when securing the brake lever.
(A)
Remove the seal plug.

Cover the seal plug with a waste cloth as
the oil applied to the seal plug may leak.
92
(A) Seal plug
BRAKE
(A)
Pass the brake hose through the hose

cover.
(A) Hose cover
5
Insert the brake hose into the joint
component.
It comes with a built-in olive. Insert it
while making sure that it will not get
snagged on the olive.
TECH TIPS
Use a waste cloth when inserting the brake
hose as some oil inside may leak.
Check that the brake hose is inserted up

to the line printed on the hose.
Tighten the connecting bolt with an

8mm spanner.
(A) 8mm spanner

Tightening torque
5 - 7 Nm
(A)
Clean any oil residue and attach the hose

cover.
93
BRAKE
(A)
Remove the brake lever stopper.
(A) Lever stopper

NOTE
After removing the lever stopper, check that
the pad spacer is installed on the caliper side
or that the caliper is installed to the bicycle
and the disc brake rotor is between the two
sides of the caliper, before depressing the
lever.
After installation to the bicycle, make sure to
check that the lever stopper is removed.
TECH TIPS
Move and pull on the lever stopper to remove
it while being careful not to depress the lever.
94
BRAKE
Overview of the easy hose joint system (For ROAD)
(A)
(A) Dual control lever

(B) Joint sleeve
(C) Lever stopper
(D) Hose cap
(E) Brake caliper
(B)
(C)
(D)
(E)
Pass the brake hose through each hole in the built-in frame.
Remove the hose cap.
Secure the joint component in a vise or

another similar device.
Face the hose connection port upward as
shown in the illustration.
Remove the seal plug.

Cover the seal plug with a waste cloth as
the oil applied to the seal plug may leak.
(A)
Pass the brake hose on the brake caliper

side through the hose cover.
95
(A) Hose cover
BRAKE
Insert the brake hose on the brake

caliper side into the joint component.
It comes with a built-in olive. Insert it
while making sure that it will not get
snagged on the olive.
TECH TIPS
Use a waste cloth when inserting the brake
hose as some oil inside may leak.
Check that the brake hose is inserted up

to the line printed on the hose.
Tighten the connecting bolt with two

8mm spanners.
(A) Connecting bolt

(B) 8mm spanner
Tightening torque
(A)
(B)
(A)
5 - 7 Nm
Clean any oil residue and attach the hose

cover.
96
(A) Hose cover
BRAKE
Replacing the brake hose (easy hose joint system)

For MTB BH59
Check the shape of the connector insert. Incorrect combinations may cause oil leakage.
(z)
(z) SHIMANO CODE No.: Y8H298040

There is a groove in the head
shaped part.
NOTE
Each connector insert has a differently
shaped hole.
Be sure to use a dedicated connector insert.

Use of any connector insert other than the
specified one may produce a loose
assembly, leading to oil leaks or other
problems.
97
BRAKE
For ROAD
Check the shape of the connector insert. Incorrect combinations may cause oil leakage.
When connecting to the joint sleeve

NOTE
When reconnecting the brake hose to the joint sleeve, make sure to use the designated connector insert supplied with SM-BH59-SB.
(A)
(z)
(z) SHIMANO CODE No.: Y8H298040

shaped part.
(A) Joint sleeve

NOTE
Each connector insert has a differently
shaped hole.
Be sure to use a dedicated connector insert.

Use of any connector insert other than the
specified one may produce a loose
assembly, leading to oil leaks or other
problems.
When connecting on the lever side

(A)
(y)
(y) SHIMANO CODE No.: Y8H298040

shaped part.
(z) For a connector insert of this

shape, only ST-R785 can be used.
(A) Brake hose connection port
(z)
98
BRAKE
Installation of the calipers and securing the hose

Remove the spacer for bleeding (yellow), and then set the wheel which has the disc brake
rotor onto the frame.
(A) Bleed spacer
1
(A)
Install the brake pads.
(A) Brake pad

(B) Snap ring
(C) Split pin
(A)
Tightening torque
(B)
2 - 4 Nm
TECH TIPS
Install the pad fixing spring as shown in the

illustration. (There are left (L) and right (R)
marks on the spring.)
For split pin
(C)
Pad fixing spring
The pads with fins have fins at the front

and back, so install them as shown in the
illustration.
Pad with fins
99
BRAKE
International standard mounting type

NOTE
For international-standard mounts, attach adapters to calipers for post-type mounts. (Separate front and rear adapters are available.)
First install the adapter, and then provisionally secure the calipers to the frame.
TECH TIPS
The calipers should be able to move sideways.
Front
Depress the brake lever so that the disc

brake rotor is being clamped by the
pads, and then tighten the caliper fixing
bolts.
(B)
(C)
(A)
(A) Adapter fixing bolt

(B) Adapter
(C) Caliper
(D) Disc brake rotor
(E) Caliper fixing bolt
Tightening torque
6 - 8 Nm
(D)
(E)
Rear
(E)
(A)
100
BRAKE
Preventing loosening of frame fixing bolts
Post mounting type
Provisionally install the caliper to the frame (so that the caliper can move sideways).
Front
Depress the brake lever so that the disc

brake rotor is being clamped by the
pads, and then tighten the caliper fixing
bolts.
(A) Caliper fixing bolt

Tightening torque
6 - 8 Nm
2
(A)

Either a cap method or a wiring method can be used to stop the bolts from falling out.
Use whichever method is suitable for the front fork and frame.
Cap method
Front
Rear
(A)
(A)
Post type
(A)
101
(A) Cap
BRAKE
Wiring method
Front
Rear
(A)
(A) Wire
(A)
Secure the two bolts with a wire as

shown in the illustration in order to
prevent the bolts from coming loose.
(A)
(z) Wind a wire around the fixing

bolt between the adapter and the
frame as shown in the illustration.
(A) Bolt
(B) Wire
(B)
(z)
TECH TIPS
If bolt [1] loosens (turns counterclockwise),
force is applied via the wire to turn bolt [2] in
the tightening direction (clockwise). However,
bolt [2] cannot turn any further in the
tightening direction.
Accordingly, this prevents bolt [1] from
turning in the loosening direction because it is
also connected via the wire.
If either one of the bolts tries to loosen, this
causes a force to be applied to the other bolt
that turns it in the tightening direction. In
other words, this system prevents the bolts
from loosening.
Post type
(B)
Bolt [1]
Bolt [2]
102
BRAKE
Securing the cable

C-shaped guide
For C-shaped guides and the usual type

of cable stoppers, use the special
Shimano cable supporter (sold
separately) to secure as shown in the
illustration.
Usual type of cable stopper
[1]
[2]
Operate the brake lever several times and check whether the brakes operate normally or
not.
Also check that there are no oil leaks.
103
Tightening torque
0.3 - 0.5 Nm
BRAKE
MAINTENANCE (HYDRAULIC DISC BRAKES)
Brake pad replacement

NOTE
This brake system is designed to automatically adjust the clearance between the disc brake rotor and the brake pads by the piston gradually protruding according to
the wear of the brake pads; therefore, when you replace the brake pads, you need to push back the piston.
TECH TIPS
If oil adheres to the brake pads, if the brake pads are worn down to a thickness of 0.5mm, or if the brake pad presser springs are interfering with the disc brake rotor,
replace the brake pads.
Remove the wheel from the frame, and

remove the brake pads as shown in the
illustration.
(A)
(B)
1
For split pin
(C)
Clean the pistons and surrounding area.
104
(A) Brake pad

(B) Snap ring
(C) Split pin
BRAKE
Use a flat-shaped tool to push the

pistons straight back in as far as they will
go, while being careful not to twist the
pistons.
(A) Piston
NOTE
Do not push the pistons with a sharp tool.
The pistons may be damaged.
(A)
Install the new brake pads, the bolt, and

the pad spacer (red).
At this point, make sure to install the
snap ring as well.
(A)
(A) Brake pad

(B) Snap ring
(C) Bolt
(D) Pad spacer (red)
Tightening torque
(B)
2 - 4 Nm
(C)
TECH TIPS
(D)
Install the pad fixing spring as shown in the

illustration. (There are left (L) and right (R)
marks on the spring.)
Pad fixing spring
105
BRAKE
For split pin types

Install the new brake pads the split pin,
and then install the pad spacers (red).
(A)
After this, bend open the split pin.

(B)
(C)
5
6
Depress the brake lever several times to check that the operation becomes stiff.
Remove the pad spacer, install the wheel, and then check that there is no interference
between the disc brake rotor and caliper.
If they are touching, adjust while referring to Installation of the calipers and securing the
hose.
106
(A) Brake pad

(B) Split pin
(C) Pad spacer (red)
BRAKE
Adjustment when the pistons are not operating correctly
Adjustment when the pistons are not operating correctly

The caliper mechanism includes two pistons; if these pistons do not operate properly or if they protrude unevenly, or if the brake pads remain in contact
with the disc brake rotor, adjust the pistons by the following procedure.
1
2
Remove the wheel and brake pads.

Clean the pistons and surrounding area.
Use a flat-shaped tool to push the pistons straight back in as far as they will go, while being
careful not to twist the pistons.
Do not push the pistons with a sharp tool.
The pistons may be damaged.
Install the brake pads and the pad spacer (red).
Depress the brake lever as far as it will go, and then operate it several more times so that
the two pistons move to their initial positions.
Remove the pad spacer, install the wheel, and then check that there is no interference
between the disc brake rotor and brake pads.
If they are touching, loosen the mounting bolts and adjust so that they are no longer
touching.
107
BRAKE
Lever stroke adjustment
Lever stroke adjustment

Tighten the adjust bolt (clockwise) to increase the stroke, and loosen it (counterclockwise) to
decrease the stroke.
(A) Reach adjustment bolt
(A)
(A)
(A)
Free stroke adjustment

When the free stroke adjustment screw is loosened, the free stroke of the brake lever will increase,
so that you can adjust it to the desired setting.
(A)
(z) Pad contact point

(A) Disc brake rotor
(B) Pad
(C) Free stroke adjustment screw
(D) Screwdriver
(z)
(B)
(y) Contact
(C)
(y)
(D)
Mineral oil replacement

It is recommended that you replace the oil inside the reservoir tank if it becomes severely discolored.
Attach a tube with a bag to the bleed nipple, and then open the bleed nipple to drain out the oil. The brake lever can be operated at this time to help
the oil drain out. After draining the fluid, pour in fresh brake fluid while referring to the "Adding mineral oil and bleeding air" section. Use only
Shimano genuine mineral oil.
Dispose of the waste oil according to proper country and/or state disposal regulations.
108
BRAKE
Adding mineral oil and bleeding air

With the spacer for bleeding (yellow) still
attached to the calipers, place the bicycle
into a bicycle stand, or the like, as shown
(A) Hose
(B) Caliper
NOTE
When bleeding the air out of the caliper, you
will need the SM-DISC (oil funnel and oil
stopper).
(A)
(B)
Set the brake lever so that it is in riding

position at 45 angle from the ground.
45
Remove the upper bleed screw and O-ring and insert the oil funnel.
(A)
(C)
(A) Bleed screw

(B) O-ring
(C) Oil funnel
TECH TIPS
(B)
Do not insert the oil stopper at this time.
109
BRAKE
Set a 7mm socket wrench in place, fill

the syringe with oil, connect a tube to
the bleed nipple, and then loosen the
bleed nipple by 1/8 of a turn to open it.
(A)
(A) Bleed nipple

(B) 7mm socket wrench
Push the piston of the syringe to add oil.
(B)
The oil will start coming out from the oil

funnel.
Continue adding oil until there are no
more air bubbles in the oil that is coming
out.
Once there are no more air bubbles mixed in with the oil, temporarily close the bleed nipple.
NOTE
Secure the brake caliper in a vise to prevent
the tube from being accidentally
disconnected.
Do not depress and release the lever
repeatedly.
Oil without air bubbles may come out as a
result of such operation, but air bubbles may
remain in the oil inside the brake caliper, and
it will take longer to bleed the air. (If you
have depressed and released the lever
repeatedly, drain out all of the oil and then
add oil again.)
110
BRAKE
Set a 7mm socket wrench in place as

shown in the illustration, and then
attach the bag to the tube.
Connect the tube to the bleed nipple
and loosen the bleed nipple.
(A)
After a little while, the oil and air

bubbles will flow naturally from the
bleed nipple into the tube.
(A) 7mm socket wrench

(B) Bag
TECH TIPS
It may help to shake the hose gently or to tap
the reservoir tank or caliper gently with a
screwdriver or move the position of the
caliper at this time.
This way it will be possible to easily

extract the greater part of the air
bubbles remaining inside the brake
system.
(B)
(z)
(z) Air bubbles
The level of liquid inside the funnel will drop at this time, so keep filling the funnel with oil
to maintain the level of liquid so that air is not drawn in (air does not get inside).
(A)
(B)
Once no more air bubbles come from the

bleed nipple, temporarily close the bleed
nipple.
111
(A) Bleed nipple

(B) 7mm socket wrench
BRAKE
With the brake lever depressed, open

and close the bleed nipple in rapid
succession (for approximately 0.5 seconds
each time) to release any air bubbles
which may be in the calipers.
(A)
(A) 7mm socket wrench

Tightening torque
4 - 6 Nm
Repeat this procedure about 2 to 3

times.
Then tighten the bleed nipple.
If the brake lever is then operated, air bubbles in the system will rise up through the port
into the oil funnel.
(x) Loose
Once the bubbles stop appearing, depress the brake lever as far as it will go.
(z) Stiff
It is normal for the lever to be stiff at this point.
(y) Slightly stiff
NOTE
If the lever does not become stiff, repeat the
procedures from step 5.
9
Lever operation
(z)
(x)
(y)
112
BRAKE
[1]
30
10
30
[2]
Set the lever unit to the horizontal

position as shown in the illustration and
tilt it in the direction of [1] by 30, and
then carry out step 9 to check that there
is no air remaining.
Next, tilt the lever unit 30 in the
direction of [2], and carry out step 9
again to check that there is no air
remaining.
If any air bubbles appear, repeat the
above procedure until they stop
appearing.
(A)
(A) Oil stopper

(B) O-ring
Remove the oil funnel while it is still

being plugged with the oil stopper, and
then attach the O-ring to the bleed
screw and tighten it until oil flows out to
make sure that there are no air bubbles
remaining inside the reservoir tank.
(A) O-ring
(B)
11
12
Plug the oil funnel with the oil stopper

so that the side with the O-ring attached
is facing downward.
(A)
Tightening torque
0.3 - 0.5 Nm
NOTE
Do not operate the brake lever. If operated,
there is a risk of air bubbles entering the
cylinder.
Wipe away any oil that has overflowed.
13
113
BRAKE
INSTALLATION (V-BRAKE BRAKES)

Use a handlebar grip with a maximum outer diameter of 32mm.
5mm hexagon wrench

Tightening torque
6 - 8 Nm
(A)
NOTE
(A)
In the case of carbon handlebars, it may be

necessary to lower the tightening torque in
order to prevent damage to the handlebar.
Please consult the bicycle or handlebar
manufacturer regarding the appropriate level
of tightening torque for carbon handlebars.
Installing the power modulator

Install the power modulator to the
V-BRAKE brake as shown in the
illustration.
(A)
(A) Power modulator

(B) V-BRAKE brake
NOTE
When the brakes are applied, the power
modulator will move about 8mm toward the
inner cable lead; make sure that there is
enough excess length in the outer casing for
that.
(B)
When brakes are applied

Outer casing
SM-PM70/
SM-PM40
Approx. 8mm
Inner cable lead
114
BRAKE
Installation of V-BRAKE brakes

Insert the stopper pin of the brake
caliper into the center spring hole in the
frame mounting boss, and then secure
the brake caliper to the frame with the
link fixing bolt.

(B) Spring hole
(C) Stopper pin
(D) Link fixing bolt
Tightening torque
(A)
5 - 7 Nm
1
(D)
(B)
(C)
(z) 32mm or more
While pressing the shoe against the rim, adjust the amount of shoe protrusion by
interchanging the washer B (thick or thin) so that dimension [A] is at 32mm or more.
(A) Washer B (thick)

(B) Shoe fixing link
(C) Washer B (thin)
(D) Shoe fixing nut
(E) Washer A
(F) Washer
(z)
[A]
(A)
(B)
(C)
FORWARD
FORWARD
(E)
115
(F)
(D)
BRAKE
(A)
While holding the shoe against the rim,

tighten the shoe fixing nut.

Tightening torque
(z) 1mm
6 - 8 Nm
3
(z)
Pass the inner cable through the inner cable lead, and after making sure the combined
clearance between the left and right shoes and the rim is a total of 2mm, tighten the cable
fixing bolt.
(z) [B] + [C] = 2mm

(A) Inner cable lead
Tightening torque
(A)
(B)
(A)
(B)
[B] [C]
[B] [C]
(z)
(z)
116
6 - 8 Nm
BRAKE
(z) 1mm
Adjust the balance with the spring adjustment bolts.
(A) Spring adjustment bolt
(A)
(A)
(z)
(z)
Depress the brake lever about 10 times

until it touches the grip and check that
everything is operating correctly and
that the shoe clearance is correct before
using the brakes.
(z) Depress about 10 times
117
BRAKE
MAINTENANCE (V-BRAKE BRAKES)
Replacement of the cartridge shoe
MAINTENANCE (V-BRAKE BRAKES)

(A)
(B)
Remove the shoe fixing pin, and then

slide the shoe along the groove to
remove it from the shoe holder.
(y) Shoe insertion direction
There are two different types of shoes and shoe holders for the left and right positions
respectively.
(z) Front
Slide the new shoes into the grooves on the shoe holders while taking note of the correct
directions and pin hole positions.
Insert the shoe fixing pins.
For left (same for front and rear)
For right (same for front and rear)
(z)
(A) Shoe
(B) Shoe holder
(C) Shoe fixing pin
NOTE
(A)
It is very critical to insert the shoe fixing pin to

keep the shoe properly fixed in place.
(B)
L
L
(y)
(C)
FORWARD
FORWARD
FORWARD
(y)
FORWARD
(B)
(z)
(A)
(A) Shoe fixing pin

(B) Shoe
(C)
118
BRAKE
BRAKE LEVER WITH SWITCH INTERCHANGEABILITY (V-BRAKE AND HUB ROLLER BRAKES)
For V-BRAKE (with power modulator) mode
BRAKE LEVER WITH SWITCH INTERCHANGEABILITY

(V-BRAKE AND HUB ROLLER BRAKES)
Four finger brake levers are equipped with a switch to change between the V-BRAKE with modulator mode and the caliper or roller brake modes.
WARNING
If the mode is not matched to the type of brake being used, this could result in inadequate or excessive braking power. Please proceed with caution when selecting
the correct mode for the corresponding brake.
For V-BRAKE (with power modulator) mode

(x) V-position
(A)
(x)
(y) V-BRAKE brakes with power

modulator
(z) Roller brake/Caliper brakes

(A) Power modulator
(y)
(x)
(z)
For Caliper brake/Roller brake

(x) Caliper/Roller (CR) brake position
(x)
(y) V-BRAKE brakes

(z) Roller brake/Caliper brakes
(y)
(x)
(z)
119
BRAKE
INSTALLATION (DUAL PIVOT CALIPER BRAKES)

Install the brake caliper.
(A)
Compress the arch and set while the

shoe is in firm contact with the rim.
(z) The usual position during

(z)
installation is when the head of

the centering adjustment bolt is

(B) 10mm spanner
Tightening torque
8 - 10 Nm
NOTE
If the brake arm touches the frame when the
handlebar is turned, attach the included
frame protection sticker to the frame.
1
For nut type
(B)
120
BRAKE
(x)
(x)
(y)
Adjust the brake shoe position and then

secure in place the brake shoe.
After adjusting the brake shoe position
so that the shoe surface and the rim
surface are as shown in the illustration,
tighten the shoe fixing bolt.
(A) Shoe fixing bolt

Tightening torque
5 - 7 Nm
(x) Direction of rim rotation

(y) Toe-in 0.5mm
(z) 1mm or more
2
(z)
(A)
(B)
Install the brake cable.
(A)
(B)
Set the quick release lever to the closed

position; then adjust the shoe clearance
(as shown in the illustration) and secure
the cable.
(x) Open
(x)
(y)
(z) 1.5 2mm

(Adjust so that the shoe
clearances on the left and right
are the same)
(C)
Tightening torque
6 - 8 Nm
(y) Close
(z)
(A) Centering adjustment bolt

(C) Quick release lever
121
BRAKE
Fine adjust the centering of the brake

shoe using the centering adjustment
bolt.
(A) Centering adjustment bolt

(z) 1.5 2mm

(A)
(B)

are the same)
(z)
(A)
Readjust shoe clearance.
(A) Cable adjustment nut
Turn the cable adjustment nut to

readjust shoe clearance.
(z) 1.5 2mm
(z)

are the same)
Check the brakes.

until it touches the grip and check that
everything is operating correctly and
that the shoe clearance is correct before
using the brakes.
TECH TIPS
For models with a CLOSE position mark on the
quick release lever and brake body side, align
the marks. At this time, check for a click.

(z)
CLOSE position mark
122
BRAKE
Arch spring tension adjustment
Arch spring tension adjustment

(B)
(A)
(y)
The spring adjustment bolt can be used

to adjust the spring tension of the arch.
(y) Reduce spring force

(z) Increase spring force
(z)
123
(A) Spring adjustment bolt

BRAKE
MAINTENANCE (DUAL PIVOT CALIPER BRAKES)
MAINTENANCE (DUAL PIVOT CALIPER BRAKES)

Remove the mounting bolt.

(B) Mounting bolt
Remove the shoe by sliding it along the

groove of the shoe holder.
(A) Shoe
(A)
(B)
(A)
(y) Shoe insertion direction
There are two different types of shoes and shoe holders for the left and right positions
respectively.
(z) Front
Slide the new shoes into the grooves on the shoe holders while taking note of the correct
directions and bolt hole positions.
Tighten the mounting bolt.
For left (same for front and rear)
For right (same for front and rear)
(z)
(z)
Tightening torque
(A)
(A)
1 - 1.5 Nm
(B)
(y)
FORWARD
FORWARD
(B)
(y)
(A) Shoe
(B) Shoe holder
(C) Mounting bolt
(C)
(C)
124
BRAKE
SPECIFICATIONS (CANTILEVER BRAKES)
Cantilever brakes
SPECIFICATIONS (CANTILEVER BRAKES)

In order to realize the best performance, we recommend that the following combination be used.
Series
CT90
Brake lever
ST-CT90/ST-CT95
SB-CT90/SB-CT91
Cantilever brakes
BR-CT91
Cable
Cantilever brakes
Model No.
Arch size
BR-CT91
M
Link type
Link wire length
L
Unit link (alignment type)
A/73
A/73
B/82
B/82
C/106
D/93
Brake lever
Model No.
ST-CT90/ST-CT95/SB-CT90/SB-CT91
Clamp diameter
22.2mm
TECH TIPS
If the link length is the same, any link wire
can be used even if the type is different.
If you have any questions about the use

and maintenance of the product, consult
the place of purchase.
125
BRAKE
INSTALLATION (CANTILEVER BRAKES)

TECH TIPS
Use a handlebar grip with an outer diameter of 32mm or less.
Install the brake lever.

ST-CT90/ST-CT95
SB-CT90/SB-CT91
6 - 8 Nm
1
(A)
Tightening torque
(A)
Connect the brake cable.
Adjust the lever stroke.

(only for ST-CT95)
126
BRAKE
Installation of the brake caliper

(A)
Install the brake caliper to the frame.

Tightening torque
5 - 7 Nm
Set the cable onto the cable carrier.
[2]
2
[1]
Temporarily tighten the cable so that the

cable carrier is at the position in the
illustration.

Temporary tightening torque
(z) Touching
(z)
0.5 - 1 Nm
(A)
Turn the spring adjustment bolt so that

the cable carrier comes to a position
directly below the outer casing holder.
(A)
127
(A) Screwdriver
BRAKE
Secure one of the shoes at a time.

Adjustment of shoe clearance is not
necessary at this time.
(A) 10mm spanner

Tightening torque
(z) 1mm
8 - 9 Nm
(A)
NOTE
When installing the shoes, make sure that

they are facing the right way and are not
back to front.
(B)
(z)
Viewed from the side of

the bicycle after
installation of the shoes is
completed
Loosen the cable fixing bolt, move the

brake caliper so that the clearance of the
flexible pipe is 2 3mm, and then secure
the inner cable.
(A)
(z)
(z) 2 3mm
(A) Flexible pipe

Tightening torque
6 - 8 Nm
(B)
Adjust so that the flexible pipe touches

the brake caliper.
(A)
(y)
(B)
(C) (z)
(y) 20mm or more

(z) Touches
128
(A) Outer casing holder

(B) Cable carrier
(C) Flexible pipe
BRAKE
If the cable carrier is in the position in

the illustration, then setting is complete.
Check to be sure that there is a clearance of

20mm or more between the outer casing
holder and the cable carrier as shown in the
illustration in step 7.
This is to ensure that the cable carrier does
not touch the outer casing holder as if it does
touch, the brakes will not work.
If balance adjustment is necessary, adjust

with the spring adjustment bolt.
10
TECH TIPS
(A)
(z)

as far as the grip and check that
everything is operation correctly before
using the brakes.
129
(A) Screwdriver
BRAKE
Installing SM-CB70
Installing SM-CB70
[1]
[2]
First, push [2] in the direction of the

arrow as shown in the illustration, and
then install to the cable.
TECH TIPS
Recommended outer casing combination:
SHIMANO SLR
If [1] and [2] are separated
[1]
[2]
Make sure the [1] logo is facing the right

way.
Adjustment method
[1]
Turn part [1] to adjust.
130
FRONT CHAINWHEEL
FRONT CHAINWHEEL
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
Intervals between maintenance depend on the use and riding circumstances. Clean regularly the chain with an appropriate chain cleaner. Never use
alkali based or acid based solvents, such as rust cleaners. If those solvent be used chain might break and cause serious injury.
The two left crank arm mounting bolts should be tightened in stages rather than fully tightened at once. Use a torque wrench to check that the final
tightening torques are within the range of 12 - 14 Nm. Furthermore, after riding approximately 100 km (60 miles), use a torque wrench to re-check
the tightening torques. It is also important to periodically check the tightening torques. If the tightening torques are too weak or if the mounting
bolts are not tightened alternately in stages, the left crank arm may come off and the bicycle may fall over, and serious injury may occur as a result.
If the inner cover is not installed correctly, the axle may rust. This may result in damage to the axle, the bicycle falling over and serious injury.
Inspect the chain for possible deformity and abnormalities such as cracks or corrosions. If damage is detected, replace the chain immediately. If you
continue to ride the bicycle in such a condition, the chain may break causing the bicycle to fall, and serious injury may result.
NOTE
In addition, if pedaling performance does not feel normal, check this once more.
Before riding the bicycle, check that there is gap or looseness in the connection. Also, be sure to retighten the crank arms and pedals at periodic
intervals.
If a squeaking noise is heard coming from the bottom bracket axle and the left crank arm connector, apply grease to the connector and then tighten it
to the specified torque.
Do not wash the bottom bracket with high-pressure jets of water.
If you feel any looseness in the bearings, the bottom bracket should be replaced.
When installing the pedals, apply a small amount of grease to the threads to prevent the pedals from sticking. Use a torque wrench to securely tighten
the pedals. Tightening torque: 35 - 55 Nm. The right-hand crank arm has a right-hand thread, and the left-hand crank arm has a left-hand thread.
Use a neutral detergent to clean the crank arm and the bottom bracket. Using alkaline or acidic detergents may cause discoloration.
Use an outer casing which still has some length to spare even when the handlebars are turned all the way
to both sides. Furthermore, check that the shifting lever does not touch the bicycle frame when the
handlebars are turned all the way.
132
Outer casing holder
FRONT CHAINWHEEL
TO ENSURE SAFETY
A special grease is used for the gear shifting cable. Do not use premium grease or other types of grease. These may cause deterioration in gear shifting
performance.
Operate the gear shifting levers only while turning the crankset.
Do not disassemble the shifting lever unit, as this may damage it or cause mis-operation.
For
MTB/Trekking
For frames with suspension, the chain stay angle will vary depending on whether the bicycle is being ridden or not.
When the bicycle is not being ridden and the chain is positioned on the largest chainring at the front and on the smallest sprocket at the rear, the
chain may come into contact with the chain guide outer plate of the front derailleur.
When installing the top route type, choose a frame that has three outer casing holders as shown in the illustration at right.
If the brake fluid used in the oil disc brakes is of a type which tends to adhere to the plastic parts of the shifting lever, this may cause the plastic parts
to crack or become discolored. Therefore, make sure that the brake fluid does not stick to these plastic parts. The Shimano genuine mineral oil which
is used in SHIMANO disc brakes does not cause cracking or discoloration if it adheres to plastic parts, but such parts should be cleaned with alcohol
beforehand to prevent foreign particles from adhering.
For
ROAD
If the bottom bracket shell is not parallel, gear shifting performance will drop.
When installing the left and right adapters, be sure to install the inner cover. Otherwise the waterproofing performance will worsen.
The gears should be periodically washed with a neutral detergent. In addition, cleaning the chain with neutral detergent and lubricating it can be an
effective way of extending the life of the gears and the chain.
If you feel any looseness in the bottom bracket axle, the bottom bracket should be replaced.
133
FRONT CHAINWHEEL
INSTALLATION (CHAINRINGS)
For ROAD
Smooth shifting will not be possible if the chainrings are incorrectly installed. Therefore, be sure to install the chainrings in the correct positions.
For ROAD
Double chainwheel set
With the marked surface of the largest chainring facing out, set the largest chainring so that
the chain drop prevention pin is lined up with the crank arm position.
(z) Outer side

(A) Crank arm
(B) Chain drop prevention pin
(z)
Tightening torque
12 - 14 Nm
(A)
(B)
With the marked surface of the smallest chainring facing away from the crank arm, set the
chainring so that the mark is lined up with the crank arm position.
(z) Inner side

(A) Crank arm
(z)
Tightening torque
12 - 14 Nm
(A)
134
FRONT CHAINWHEEL
For MTB/Trekking
Triple chainwheel set

(z) FC-5703 (39T)
(A) Crank arm
Tightening torque
12 - 14 Nm
(z)
(A)
For MTB/Trekking
Triple chainwheel set
(A) Crank arm
Largest chainring/middle chainring
Tightening torque
14 - 16 Nm
Smallest chainring
Tightening torque
16 - 17 Nm
(A)
135
FRONT CHAINWHEEL
INSTALLATION (FRONT CHAINWHEEL)
HOLLOWTECH II / 2 piece crankset

Installation of crank
Grease the left and right hand adapters
and use the Shimano original tool to
install the right hand adapter of the
bottom bracket, the inner cover and the
left hand adapter of the bottom bracket.
(A) TL-FC32
(B) Inner cover
(C) Right hand adapter
(counterclockwise thread)
(D) Left hand adapter

(clockwise thread)
(A)
Tightening torque
(B) (C)
35 - 50 Nm
(D)
NOTE
Tighten TL-FC24/TL-FC25 by combining with
TL-FC32/TL-FC33/TL-FC36.
TL-FC24/FC25 may become damaged and

unusable after repeated use.
NOTE
For MTB/Trekking
Spacers used vary according to the width of
the bottom bracket shell. For details, refer to
Spacer installation method (For MTB/
Trekking).
TECH TIPS
Turn the right hand adapter clockwise when
the 70mm [M36] bottom bracket is used
(clockwise thread).
136
FRONT CHAINWHEEL
Insert the right crank arm unit.
Set the wide groove area of the left

crank arm into the axle of the right
crank arm unit where the groove is wide.
(A)
(A) Wide groove area (left crank arm)

(B) Wide groove area (axle)
NOTE
Insert a spacer for the triple specification of
road bikes and the double guard specification
of comfort bikes.
3
(B)
Use the Shimano original tool to tighten

the cap.
(A) TL-FC16
(B) Cap
(C) Left crank arm
Tightening torque
(B)
0.7 - 1.5 Nm
(C)
(A)
137
FRONT CHAINWHEEL
(C)
(z)
(A)
Push in the stopper plate and check that

the plate pin is securely in place, and
then tighten the bolt of the left crank
arm.
(z) The illustration is of the left crank

arm (cross-section)
(A) Plate pin

(B) Stopper plate
(C) Left crank arm
Tightening torque
12 - 14 Nm
NOTE
Each of the bolts should be evenly and
(B)
equally tightened.
Set the stopper plate in the correct

direction as shown in illustration.
138
FRONT CHAINWHEEL
Spacer installation method (For MTB/Trekking)

Check whether the width of the bottom
bracket shell is 68mm or 73mm.
(z) Bottom bracket shell width
1
(z)
Install the adapter. See the illustrations for the normal type or chain case type, depending on
the type of your front chainwheel.
Normal type
68mm
73mm
[1] 2.5mm spacer

[2] 1.8mm spacer
[2]
[3] 0.7mm spacer
[3]
TECH TIPS
Band type
[1]
[1]
[1] (A)
(A)
If using three 2.5mm spacers with a band type

and a bottom bracket shell having a width of
68mm, install the three spacers so that there
are two on the right and one on the left.
[1] 2.5mm spacer

(A) BB mount-type bracket
Bracket type
[1]
139
FRONT CHAINWHEEL
Chain case specifications

68mm
73mm
[1] 2.5mm spacer

[2] 1.8mm spacer
[2]
* 1.8mm corresponds to the

thickness of the chain case.
[3]
[3] 0.7mm spacer
Band type
TECH TIPS
[1]
[1]
[1] (A)
If using three 2.5mm spacers with a band type

and a bottom bracket shell having a width of
68mm, install the three spacers so that there
are two on the right and one on the left.
(A)
[1] 2.5mm spacer

(A) BB mount-type bracket
Bracket type
[1]
(A)
[2]
(A)
[2]
[1] 2.5mm spacer

[2] 0.7mm spacer
Chain case stay

type
(A) Chain case stay

[1]
140
FRONT CHAINWHEEL
OCTALINK TYPE
OCTALINK TYPE
Installation of the bottom bracket
Apply grease to the main body, and
install using the Shimano original tool.
First install the main body, then the
adapter.
(A) Adapter
(B) Body
Tightening torque
50 - 70 Nm
(A)
(B)
NOTE
If the adapter is made of aluminum or steel
Apply grease to the adapter.
If the adapter is made of plastic

Do not apply grease to the adapter.
Installation of the front chainwheel

Use a hexagon wrench to install the
front chainwheel.

10mm hexagon wrench
Tightening torque
(A)
35 - 50 Nm
141
FRONT CHAINWHEEL
SQUARE TYPE
SQUARE TYPE
Installation of the bottom bracket
(C)
Install using the Shimano original tool.

First install the main body, then the
adapter.
(A) Adapter
(B) Body
(C) Front Chainwheel
Tightening torque
(A)
(B)
50 - 70 Nm
NOTE
If the main body and adapter are made of
aluminum or steel
Apply grease to the main body and adapter.
If the main body and adapter are made of

plastic
Do not apply grease to the main body or
adapter.
142
FRONT CHAINWHEEL
SQUARE TYPE
Installation of the front chainwheel

If using a hexagon wrench
Use a hexagon wrench to install the
front chainwheel.

10mm hexagon wrench
Tightening torque
(A)
35 - 50 Nm
If using a Shimano original tool

Use the Shimano original tool to install
the front chainwheel.
(A) TL-FC10/TL-FC11
(B) 15mm spanner
Tightening torque
(A)
(B)
35 - 50 Nm
143
FRONT CHAINWHEEL
INSTALLATION (PRESS-FIT BOTTOM BRACKET)
Adapter

Adapter
(A)
(B)
(z) Bottom bracket shell width
(C)
(A) Left hand adapter

(B) Inner cover
(C) Right hand adapter
(D) 2.5mm spacer
(z)
(D)
Assembly example
Adapter type
Inner cover cannot be

installed
If the frame has no

openings inside the bottom
bracket shell, it can be
installed without the inner
cover sleeve.
ROAD
MTB
Use for a bottom bracket shell width

of 86.5mm.
-
Use for a bottom bracket shell width

of 86.5mm. The 2.5mm spacer is not
necessary.
The 2.5mm spacer is not needed for a

bottom bracket shell width of 92mm.
Use the inner cover.
Inner cover can be installed
If the frame has openings

inside the bottom bracket
shell, it should be installed
with the inner cover sleeve
to prevent possible
contamination.
For a bottom bracket shell width of

89.5mm, insert the 2.5mm spacer into
the right hand side (between the
frame and the right hand adapter).
144
FRONT CHAINWHEEL
Installation
Installation
Insert the bottom bracket into the
bottom bracket shell.
(A)
Insert the Shimano original tool into the

bottom bracket.
(A) TL-BB12
Press fit the bottom bracket by

tightening with a spanner while making
sure that the contact surface of the
bottom bracket stays parallel to the
contact surface of the bottom bracket
shell.

(B) 17mm spanner
(B)
(A)
Check to confirm that there is no gap

between the bottom bracket and the
bottom bracket shell.
145
FRONT CHAINWHEEL
Removal
Removal
Insert the Shimano original tool into the
bottom bracket.
(A) TL-BB13
(A)
As shown in the illustration, hold down

the flap with your fingers and push it in
from the opposite side.
(When pushed in, the flap opens.)
TECH TIPS
While holding down the end of the removal
tool, push the tool in from the other side until
it locks in place.
Tap the Shimano original tool with a

plastic mallet until the end of the
bottom bracket is ejected.
(A) Plastic mallet
Tap the opposite end of the bottom

bracket in the same way and remove it.
(A) Plastic mallet
3
(A)
NOTE
Do not reuse the adapters as they can be
damaged during removal.
4
(A)
146
TO ENSURE SAFETY
TO ENSURE SAFETY
For information on the ClickR pedals and the flat pedals, refer to the dealers manual for each product.
WARNING TO PARENT/GUARDIAN
To avoid serious injuries:
USE OF THIS PRODUCT IN ACCORDANCE WITH THESE DEALERS MANUAL IS ESSENTIAL FOR YOUR CHILDS SAFETY. MAKE SURE YOU AND YOUR CHILD
UNDERSTAND THESE DEALERS MANUALS. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN SERIOUS PERSONAL INJURY.
WARNING
Be sure to also inform users of the following:
If the warnings below are not followed, your shoes may not come out of the pedals when you intend or they may come out
unexpectedly or accidentally, and severe injury may result.
Common
descriptions regarding SPD-SL/SPD pedals

SPD-SL/SPD pedals are designed to be released only when intended. They are not designed to be released automatically when you have fallen off the
bicycle.
Before attempting to ride with these pedals and shoes, make sure you understand the operation of the engagement/release mechanism for the pedals
and cleats (shoes).
Before you attempt to ride with these pedals and shoes, apply the brakes, then place one foot on the ground and practice engaging and releasing
each shoe from its pedal until you can do so naturally and with minimal effort.
Ride on level ground first until you become accustomed to engaging and releasing your shoes from the pedals.
Before riding, adjust the spring tension of the pedals to your liking. If the spring tension of the pedals is low, the cleats may become accidentally
released and you may lose balance and fall off the bicycle. If the spring tension of the pedals is high, the cleats cannot be easily released.
When riding at low speed or when there is a possibility that you might need to stop riding, (for example, when doing a U-turn, nearing an
intersection, riding uphill or turning a blind curve), release your shoes from the pedal beforehand so that you can quickly put your feet onto the
ground at any time.
Use a lighter spring tension for attaching the pedal cleats when riding in adverse conditions.
Keep cleats and bindings out of dirt and debris to ensure proper engagement and release.
Remember to check the cleats periodically for wear. When the cleats are worn, replace them, and always check the spring tension before riding and
after replacing the pedal cleats.
Be sure to attach reflectors to the bicycle when riding at night. Do not continue riding the bicycle if the reflectors are dirty or damaged. Otherwise, it
becomes more difficult for others to see you.
Use only Shimano cleats and make sure that the mounting bolts are tightened securely to the shoes. Refer to the dealers manual for each product for
applicable cleats.
148
TO ENSURE SAFETY
Descriptions
regarding SPD-SL pedals

Use only SPD-SL shoes with this product. Other types of shoe may not release from the pedals, or may release unexpectedly.
Descriptions
regarding SPD pedals

Use only SPD shoes with this product. Other types of shoe may not release from the pedals, or may release unexpectedly.
CAUTION
To avoid serious injuries:
SPD
PEDALS
PD-M324 can be fitted with toe clips, but the toe clips should be removed when using the pedals as SPD pedals.
NOTE
Before riding the bicycle, check that there is no play or looseness between connecting parts.
Check that there is no looseness in cleat or spacer before riding the bicycle.
If pedaling performance does not feel normal, check the bicycle once more.
If you experience any trouble with the rotating parts of the pedal, the pedal may require adjustment. Consult a dealer or an agency.
Be sure to retighten the crank arms and pedals at periodic intervals at the place of purchase or a bicycle dealer.
Optional reflector sets are available. Reflector sets vary depending on the model of the pedals, therefore, consult a dealer or an agency.
Products are not guaranteed against natural wear and deterioration from normal use and aging.
For maximum performance we highly recommend Shimano lubricants and maintenance products.
149
INSTALLATION (SPD PEDALS)
Engaging the cleats with the pedals

NOTE
Single release mode cleats (SM-SH51) and multiple release mode cleats (SM-SH56) are available for use with these pedals.
Each type of cleat has its own distinctive features, so be sure to follow these instructions carefully and select whichever type of cleat best suits your riding style and the
terrain and riding conditions which you will encounter.
Other types of cleats, such as single release mode cleats (SM-SH52) and multiple release mode cleats (SM-SH55), cannot be used as they do not provide stable enough
step-out performance or sufficient holding force.

Press the cleats into the pedals with a
forward and downward motion.
Releasing the cleats from the pedals

The method of release varies according to the type of cleats you are using.
(Check the model number and color of your cleats to determine the proper method of release.)
Single release mode cleats: SM-SH51 (black)

These cleats only release when the heel is moved outward. They will not release if the heel is twisted in any other direction.
Upward force may be applied to the pedal, since they will not release unless the foot is twisted outward.
The cleats will not necessarily release if you lose your balance. Accordingly, for places and conditions where it looks as though you may lose balance,
make sure that you have sufficient time to release the cleats beforehand.
When you are pedaling vigorously, your heel may inadvertently twist outward and this may cause the cleat to release accidentally. If the cleat releases
by accident, you may fall off the bicycle and serious injury may result. You can help to prevent this by adjusting the amount of force required to
release the cleats. You should practice until you are accustomed to the amount of force and the angle required to release the cleats.
Single release mode

These cleats only release when the heel
is moved outward.
150
NOTE
It is necessary to practice releasing until you
become accustomed to the technique.
Multiple release mode cleats: SM-SH56 (silver, gold)

The cleats can be released by twisting in any direction.
Because the cleats can also be released by lifting your heel, they may become accidentally released when applying upward force on the pedals. These
cleats should not be used for riding style which may involve pulling up on the pedals or for activities, such as jumping. In such riding styles, pulling
forces are applied to the pedals causing possible release from the pedals.
Although the cleats can be released by twisting your heels in any direction, or by lifting, they will not necessarily release if you lose your balance.
Accordingly, for places and conditions where it looks as though you may lose balance, make sure that you have sufficient time to release the cleats
beforehand.
If the cleat releases by accident, you may fall off the bicycle and serious injury may result. If the use of the multiple release mode cleats are not
sufficiently understood or used correctly, they may release accidentally more frequently than single release mode cleats.
You can help to prevent this by adjusting the amount of force required to release the cleats. You should practice until you are accustomed to the
amount of force and the angle required to release.
Multiple release mode

Release the cleats from the pedals by
twisting your heels in any direction.
151
NOTE
It is necessary to practice releasing until you
become accustomed to the technique.
Releasing by lifting your heel requires
particular practice.
Attaching the cleats

Set the cleat on the bottom of each shoe as shown in the illustration, and then tighten the cleat mounting bolts, temporarily.
With a pair of pliers or a similar tool, pull
off the rubber cover to expose the cleat
mounting holes.
(A) Rubber cover for cleat mounting

holes
(B) SPD shoe

NOTE
This step may not be necessary depending on
the type of shoe.
(A)
(B)
(A)
(B)
Remove the sockliner and position a

cleat nut over the oval holes.
(A) Cleat nut

(B) Sockliner
NOTE
This step may not be necessary depending on

the type of shoe.
Position the cleat then the cleat adapter

on to the bottom of the shoe and then
tighten with the cleat mounting bolts.
(A)
(B)
(C)
(D)
(z)
The cleats are compatible with both left

and right pedals.
(z) Position the triangular portion of

the cleat toward the front of the
shoe.
152

(B) Cleat mounting bolt
(C) Cleat adapter
(D) Cleat
Provisional tightening torque for cleat
mounting bolts
2.5 Nm
Adjustment of cleat position

The cleat has an adjustment range of
20mm front to back and 5mm right to
left.
After temporarily fixing the cleats, adjust
them by repeatedly engaging and
releasing the cleats, one by one, to
determine the optimal necessary cleat
positions.
After you have determined the best cleat position, firmly tighten the cleat mounting bolts
with a 4mm hexagon wrench.
Tightening torque
5 - 6 Nm
Waterproof seal
(A)
(B)
Remove the sockliner and attach the

waterproof seal.
(A) Waterproof seal

(B) Sockliner
NOTE
The waterproof seal is supplied with Shimano
shoes that require this step to be carried out.
153
Mounting the pedals on the crank arms
Apply a small amount of grease to the thread to prevent sticking.
Use an 8mm hexagon wrench or a 15mm

spanner to install the pedals to the
cranks.
(z) Note the markings

R: Right pedal, L: Left pedal

(B) 15mm spanner
Tightening torque
35 - 55 Nm
(A)
NOTE
A 6mm hexagon wrench cannot provide a
sufficient tightening torque.
Always be sure to use a 15mm spanner.
(z)
TECH TIPS
(B)
The right pedal has a right-hand thread; the

left pedal has a left-hand thread.
Remove any roughness or bumps on the joint, if detected.
154
Adjusting the spring tension of the binding

The spring force is adjusted by means of
adjustment bolts.
(A)(B)
The adjustment bolts are located behind

each of the bindings, and there are two
adjustment bolts on each pedal.
Equalize the tensions by referring to the
adjustment plates and by counting the
number of turns of the adjustment bolts.
(y)
(z)
(A)
(A) Adjustment bolt

(B) Adjustment plate
TECH TIPS
When the adjustment bolt is turned clockwise,
the spring tension increases, and when it is
turned counterclockwise, the spring tension
decreases.
The spring tension can be adjusted by

four steps each turn of the adjustment
bolt.
(y) Increase
(z) Decrease
Cleat replacement
Cleats wear out over time and should be replaced periodically. Cleats should be replaced when it becomes difficult to release, or it starts to release with
much less effort than the when it was in new condition.
155
INSTALLATION (SPD-SL PEDALS)
Cleat types

Cleat types
SM-SH10
SM-SH11
(PD-R540-LA: standard)
SM-SH12
(PD-9000: standard)
Red
Yellow
Blue
Wide
Narrow
Wide
Fixed mode
There is no looseness when the shoes are firmly
engaged with the pedals. There is no looseness.
Self-aligning mode
There is some sideways looseness when the
shoes are engaged with the pedals.
156
Front center pivot mode

There is some sideways looseness centered on
the front of the shoes.

Press the cleats into the pedals with a
forward and downward motion.

These cleats only release when the heel
is moved outward.
NOTE
Place one foot on the ground and practice
engaging and releasing the cleat from the
pedal several times. Set the spring tension to
the tension you prefer when releasing the
cleat.

(A)
(B)
(C)
Set the cleat on the bottom of each shoe

as shown in the illustration, and then
tighten the cleat mounting bolts.
Refer to the Service Instructions provided
with your shoes for further details.

(B) Cleat mounting bolt
(C) Cleat washer
(D) Cleat
NOTE
When installing the cleats, use the provided
cleat mounting bolts and washers. If you use
any other cleat mounting bolts, it may
damage the cleats and cause problems with
installation.
(D)
157
Adjustment of cleat position
The cleat has an adjustment range of 15mm front to back and 5mm right to left.
After provisionally tightening the cleat, practice engaging and releasing, one shoe at a time.
After you have determined the best cleat

position, firmly tighten the cleat
mounting bolts with a 4mm hexagon
wrench.
Tightening torque
5 - 6 Nm
Apply a small amount of grease to the thread to prevent sticking.
Use an 8mm hexagon wrench or a 15mm

spanner to install the pedals to the
cranks.
(z) Note the markings

R: Right pedal, L: Left pedal

(B) 15mm spanner
Tightening torque
35 - 55 Nm
(A)
NOTE
A 6mm hexagon wrench cannot provide a
sufficient tightening torque. Always be sure
to use a 15mm spanner.
(z)
TECH TIPS
The right pedal has a right-hand thread; the
left pedal has a left-hand thread.
(B)
Remove any roughness or bumps on the joint, if detected.
158
(y)
(A)
The spring force is adjusted with the

adjustment bolts.
(z)
Adjust the spring force to the optimal

cleat holding force when releasing the
cleats from the bindings.
(B)
Equalize the spring tensions for both

pedals by referring to the tension
indicators and by counting the number
of turns of the adjustment bolts.
(C)
(y)
(z)
The spring tension can be adjusted by

four steps each turn of the adjustment
bolts; each adjustment bolt can be
turned up to three full turns.
(y) Decrease
(z) Increase
(A) 2.5mm hexagon wrench

(B) Adjustment bolt
(C) Indicator
NOTE
In order to prevent accidental release,
make sure all the spring tensions are
properly adjusted.
The spring tensions for the right and left

pedals should be adjusted so they are
equal.
If the cleats are not adjusted equally, it can
cause the rider difficulty in engaging or
releasing the pedals.
If the adjustment bolt is completely

withdrawn from the spring plate,
disassembly and reassembly will be
required. If this occurs, ask a professional
dealer for assistance.
Do not turn the bolt past the point at

which the indicator shows the maximum or
minimum tension.
Cleat replacement
(A)
(y)
(x)
Cleats wear out over time and should be

replaced periodically.
Cleats should be replaced when it
becomes difficult to release, or it starts
to release with much less effort than the
when it was in new condition.
(z)
(A) Cleat
NOTE
If the yellow (SM-SH11) or red (SM-SH10) or
blue (SM-SH12) portions of the cleats become
worn, replace the cleats with new ones.
Front: Replace the cleats when the base layer
underneath the cleats starts to be
visible.
(x) Front
(y) Rear
Rear: Replace when section A in the

illustration becomes worn.
(z) A
159
Replacement of the body cover
Replacement of the body cover

For information on how to replace the body cover, refer to the dealers manual for each product.
Maintenance of the axle units

If you experience any trouble with the rotating parts of the pedal, the pedal may require adjustment.
Mounting the reectors (optional)

Use a reflector (separately sold) designed for each pedal. For information on installation, refer to the included manual.
160
HUB DYNAMO
HUB DYNAMO
TO ENSURE SAFETY
TO ENSURE SAFETY
WARNING
Check that the wheels are fastened securely before riding the bicycle. If the wheels are loose in any way, they may come off the bicycle and serious
injury may result.
Check that the light illuminates normally when riding at nighttime.
For Installation to the Bicycle, and Maintenance:

Depending on the hub dynamo, the tire diameter of the compatible wheel may differ. Be sure to check the compatible size. If an incompatible size is
used, the wheels may lock and you may lose balance and fall off the bicycle.
If the total weight of the bicycle (bicycle + rider + luggage) is indicated on the hub body, the power modulator that controls an excessive braking
effect is built in. Use the compatible brake lever together. If the total weight of the bicycle is heavier than the recommended range, braking may be
insufficient; if lighter, braking will be too effective and the wheel may be locked, which may cause you to fall off the bicycle. The power modulator is
not an anti-locking device of the wheel.
CAUTION
The hub dynamo generates an extremely high voltage. Never touch the connection terminal of the hub dynamo directly while riding the bicycle or
while the wheel is spinning. Touching the dynamo terminal may cause an electric shock.
NOTE
Be sure to install the hub dynamo to the front fork so that the side with the connection terminal is on the right when facing toward the front of the
bicycle. If the side with the connection terminal is facing toward the left, the hub dynamo may not turn properly while riding.
Check that the hub dynamo connection terminal is securely connected before using the hub dynamo.
If the bulb of either the front light or tail light burns out, excessive voltage will be applied to the remaining light and shorten the operating life of the
bulb, so any burned out bulbs should be replaced as soon as possible.
If the light is frequently turned on when riding at high speed ranges, it will shorten the operating life of the bulbs.
Lights with electrical circuits such as automatic lights may become damaged if the bicycle is ridden at high speeds.
The hub dynamo will cause the turning of the wheel to become slightly heavier because of the magnet inside the hub.
For Installation to the Bicycle, and Maintenance:

According to German regulations (StVZO), a hub dynamo in Germany requires overvoltage protection. This hub dynamo (3.0W) does not have
overvoltage protection inside the hub itself. Use an external overvoltage protector with a symbol to show that it complies with the German
regulations (overvoltage protector product).
Check that the front fork end is aligned. If the front fork end is severely misaligned, deformation of the hub axle may cause noise from an obstruction
inside the hub dynamo.
Do not lubricate the internal parts of the hub. Otherwise the grease will come out and it may cause problems with conductivity.
162
HUB DYNAMO
TO ENSURE SAFETY
Compatible
lights
3.0W hub dynamo
Front light
Tail light
6.0V/2.4W
6.0V/0.6W
6.0V/3.0W
9.6V/5.0W
Front light
Tail light
6.0V/2.4W
Front light
Tail light
6.0V/0.9W
2.4W hub dynamo
1.5W hub dynamo

Use LED light only.
0.9W hub dynamo
163
HUB DYNAMO
INSTALLATION (HUB DYNAMO)

Please refer to the DISC BRAKE section.
Installation of the front wheel

Install the wheel so that the side with the hub dynamo connection terminal is on the right side when looking toward the front of the bicycle, and so
that the hub connection terminal is aligned with the front fork or with the basket stay. Then install following the procedure shown in the illustration so
that the connection terminal is facing up.
Do not force the connection terminal to turn after the quick release lever or the hub nut has been secured. If you force the connection terminal to turn,
it may become damaged, or the wire inside the connection terminal may break.
For quick release type

(A) Front fork
(B) Connection terminal
(C) Mudguard stay
(D) Quick release nut
(E) Volute spring
Before installing
(C)
(A)
(B)
NOTE
Do not use the toothed axle washer with a
quick release type.
(D)
(E)
Connect the two wires to ensure that the
current flows smoothly.
After installing
(A)
(B)
(C)
(D)
164
HUB DYNAMO
For nut type

For E2 type
(A) Hub nut (M9)
(B) Washer
(C) Basket stay
(D) Mudguard stay
(E) Front fork
(F) Connection terminal
Before installing
(F)
(A) (B)
(C) (D)
(E)
Tightening torque
20 - 25 Nm
After installing
(C)
(F)
(E)
(D)
For J2 type
(H)
(A)
(B)
(C) (D) (E)
(F)
(G)
(A) Flange nut

(B) Washer
(C) Basket stay
(D) Mudguard stay
(E) Front-wheel anti-falloff fitting
(F) Front fork
(G) Toothed washer for axles
(H) Connection terminal
Tightening torque
20 Nm
165
HUB DYNAMO
For J2-A type

(G)
(A)
(B)
(C)
(D) (E)
(F)
(A) Flange nut

(B) Washer
(C) Basket stay
(D) Mudguard stay
(E) Front-wheel anti-falloff fitting
(F) Front fork
(G) Connection terminal
Tightening torque
20 Nm
NOTE
When tightening the hub nuts or flange nuts,
tightening the hub nut only on one side
excessively may force the hub axle to turn,
tightening or loosening the lock nut
excessively; therefore, tighten both nuts
alternately.
166
HUB DYNAMO
CONNECTION OF THE CABLES
For E2 type

If you wish to replace the connector or change the length of the cable, perform the following procedure.
For E2 type
Hub dynamo connection terminal
Twist the conducting wires of the cable

together before connecting them so that
they stay together.
(z) Approx. 16mm
(B)
(A)
(A) Frame connection terminal

(B) Light connection terminal
(C) Frame cable
(D) Light cable
(E) Connector cap (gray)
(F) Connector cover (black)
(G) Frame connection terminal
(H) Light connection terminal
NOTE
Do not mix up the frame cable and the light

cable by mistake. If the cables are connected
incorrectly, the light will not turn on.
(C)
TECH TIPS
(D)
(z)
Recommended wire specification
(z)
Wire
(E)
Insulation
(F)
Type
Stranded
Wire
Size (AWG) 22
Diameter: approx. 0.8mm
(G)
Insulation
(H)
167
Diameter: 1.8 2mm
HUB DYNAMO
For J2 type
Bend the cable wires and run them along

the grooves.
(y)
(A) Groove
NOTE
(y) Insert
(z) Bend
Do not allow the cable wires to touch each

other.
(A)
(z)
(A) Connector cap (gray)

(B) Connector cover (black)
Press in until you hear a click.
(A)
NOTE
Set so that it faces the right way.
3
(B)
For J2 type
(A)
(z) Connect
(C)
(D)
(A) Basket stay
(B) Front fork
(C) Light cable
(D) Frame (grounding) cord
(E) Light connection terminal (small)
(F) Frame (grounding) connection
(B)
(z)
(z)
(E)
(F)
terminal (large)
TECH TIPS
If the frame (grounding) connection terminal
is fitted with a cover, remove it before
connection.
168
HUB DYNAMO
For J2-A type
For J2-A type

Hub dynamo connection terminal
Twist the conducting wires of the cable

together before connecting them so that
they stay together.
1
(A)
(B)
(C)
Open the connector using a slotted

screwdriver or similar tool as shown in
the illustration.
Insert the cable with the marking into

the ground side of the connector.
(y) Approx. 16mm

(y)
(z) Ground side
(y)
3
(z)
169
(A) Mark
(B) Connector
(C) Connection terminal
HUB DYNAMO
For J2-A type
Twist the cable wires, pass them through

the connector, bend them, and run them
along the grooves.
(y)
(y) Insert
(z) Bend
(A)
(z)
Close the connector until you hear a

click.
170
(A) Groove
NOTE
Do not allow the cable wires to touch each
other.
HUB DYNAMO
Note on the connection of the cables
Note on the connection of the cables

Secure the cable to the front fork or the basket stay so that it will not get caught in the spokes or any other parts while riding. If the position of the
hub dynamo changes with respect to the light while riding, for example when using a suspension fork, make sure that the cable is connected so that it
will not be too loose or too tight at any point.
Connect so that the current from the hub dynamo flows through the cable from the light connection terminal to the frame connection terminal.
To disconnect the light from the hub dynamo, remove the connector cover/light cord and frame (grounding) cord.
Do not ride the bicycle with the connector cover, light cord or frame (grounding) cord removed. The cord may be entangled in the wheel.
Remove the connector cover/light cord and frame (grounding) cord before removing the wheel. If the cables are pulled strongly, it may break the
cable wires or cause poor connection. Furthermore, when installing the wheel, first secure the wheel to the front forks and then connect the
connector cover/light cord and frame (grounding) cord.
(y) Remove
(z) Connect
(A)
(B)
(A)
(y)
(C)
(z)
(A) Connector cover

(B) Cord
(C) Front fork
(y) Remove
(z) Connect
(A)
(B)
(E)
(C)
(z)
(y)
(F)
(D)
(A) Light cable

(B) Frame (grounding) cord
(C) Light connection terminal (small)
(D) Frame (grounding) connection
terminal (large)
(E) Cord
(F) Front fork
Checking the light illumination

Rotate the front wheel and check that
the light illuminates.
171
HUB DYNAMO
MAINTENANCE (HUB DYNAMO)
Checking the light illumination
MAINTENANCE (HUB DYNAMO)

(A)
36
When replacing the internal parts of a

hub dynamo, it is recommended to use a
genuine Shimano tool TL-DH10
(Y-12009000).
(A) TL-DH10 (Y-12009000)

Tightening torque
AN
H1
-D
54 Nm
32
TL
P
JA
172
MULTIPLE FREEWHEEL
MULTIPLE FREEWHEEL
INSTALLATION (MULTIPLE FREEWHEEL)
Installation of the freewheel
INSTALLATION (MULTIPLE FREEWHEEL)

Installation of the freewheel
(y) Installation
(y)
(z) Removal
(A)
(A) Freewheel removal tool (TL-FW30)
(z)
Tightening torque
30 Nm
174
Please note: specifications are subject to change for improvement without notice. (English)
Aug. 2016 by Shimano Inc. HTR

Shimano Dealers Manual

Uploaded by

Copyright:

Available Formats

Shimano Dealers Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Shimano Dealers Manual

Uploaded by

Copyright:

Available Formats

DM-GN0001-18

REAR DERAILLEUR FOR ROAD.......................................................................................... 25

FRONT DERAILLEUR FOR ROAD........................................................................................ 53

INSTALLATION (HYDRAULIC DISC BRAKES)..................................................................... 86

MAINTENANCE (HYDRAULIC DISC BRAKES).................................................................. 104

INSTALLATION (V-BRAKE BRAKES)................................................................................. 114

MAINTENANCE (V-BRAKE BRAKES)................................................................................ 118

BRAKE LEVER WITH SWITCH INTERCHANGEABILITY

INSTALLATION (DUAL PIVOT CALIPER BRAKES)............................................................ 120

MAINTENANCE (DUAL PIVOT CALIPER BRAKES)........................................................... 124

SPECIFICATIONS (CANTILEVER BRAKES)........................................................................ 125

INSTALLATION (CANTILEVER BRAKES)........................................................................... 126

TO ENSURE SAFETY......................................................................................................... 132

INSTALLATION (FRONT CHAINWHEEL)........................................................................... 136

INSTALLATION (PRESS-FIT BOTTOM BRACKET)............................................................. 144

PEDALS (SPD-SL PEDALS/SPD PEDALS)

TO ENSURE SAFETY......................................................................................................... 148

INSTALLATION (SPD-SL PEDALS)..................................................................................... 156

TO ENSURE SAFETY......................................................................................................... 162

CONNECTION OF THE CABLES........................................................................................ 167

MAINTENANCE (HUB DYNAMO)................................................................................... 172

INSTALLATION (MULTIPLE FREEWHEEL)......................................................................... 174

Aluminum cap (4mm)

REAR DERAILLEUR FOR MTB/TREKKING

Installation of the rear derailleur

REAR DERAILLEUR FOR MTB/TREKKING

(A) 5mm hexagon wrench

REAR DERAILLEUR FOR MTB/TREKKING

Installation of the rear derailleur

(A) Fork end

Periodically check that there is no gap

For BMX type

REAR DERAILLEUR FOR MTB/TREKKING

Turn the top adjustment bolt to adjust so

(A) Outer line of smallest sprocket

Turn the low adjustment bolt so that the

(A) Largest sprocket

REAR DERAILLEUR FOR MTB/TREKKING

Consequently, an excessive load may be

The rear suspension operates and stops

Mount the chain on to the largest

Next, add 2 links to set the length of the

(A) Largest sprocket

The rear derailleur plate assembly is

equipped with a pin or plate that prevents

REAR DERAILLEUR FOR MTB/TREKKING

Securing the cable

Securing the cable

After cutting the outer casing, make the

After cutting, attach the same sealed

(A) Outer cap

(z) Be careful not to bend this

(A) Sealed outer cap with tongue

REAR DERAILLEUR FOR MTB/TREKKING

Securing the cable

Outer casing length for SHADOW RD

(A) B-tension adjust bolt

Check that there is enough slack in the

(A) Outer casing holder

Next, align the outer casing with the