Exam review

Exam ref: BASIC09.2013-M07-B1-B-1

Prepared by: R. Rozman
Date: 19-sep-13

Description: Basic 09.2013 - M07 - B1 - B - 1

Module Description No of questions
M07.00 MAINTENANCE PRACTICES 4

M07.01 Safety Precautions-Aircraft and Workshop 2

M07.02 Workshop Practices 9

M07.03 Tools 4

M07.05 Engineering Drawings, Diagrams and Standards 14

M07.06 Fits and Clearances 4

M07.08 Riveting 1

M07.09 Pipes and Hoses 7

M07.11 Bearings 3

M07.17 Aircraft Handling and Storage 7

M07.18 Dis assembly, Inspection, Repair and Assembly Te 2

M07.19 Abnormal Events 11

M07.20 Maintenance Procedures 12

19. september 2013 Page 1 of 1

Correct answers - for instructor's use only!
Exam ID: Basic09.2013-M07-B1-B-1

Question No Corr. answer Question No Corr. answer Question No Corr. answer

1 .) A B C 20 .) A B C 39 .) A B C

2 .) A B C 21 .) A B C 40 .) A B C

3 .) A B C 22 .) A B C 41 .) A B C

4 .) A B C 23 .) A B C 42 .) A B C

5 .) A B C 24 .) A B C 43 .) A B C

6 .) A B C 25 .) A B C 44 .) A B C

7 .) A B C 26 .) A B C 45 .) A B C

8 .) A B C 27 .) A B C 46 .) A B C

9 .) A B C 28 .) A B C 47 .) A B C

10 .) A B C 29 .) A B C 48 .) A B C

11 .) A B C 30 .) A B C 49 .) A B C

12 .) A B C 31 .) A B C 50 .) A B C

13 .) A B C 32 .) A B C 51 .) A B C

14 .) A B C 33 .) A B C 52 .) A B C

15 .) A B C 34 .) A B C 53 .) A B C

16 .) A B C 35 .) A B C 54 .) A B C

17 .) A B C 36 .) A B C 55 .) A B C

18 .) A B C 37 .) A B C 56 .) A B C

19 .) A B C 38 .) A B C 57 .) A B C

Printed: 19. september 2013 Page 1 of 2

Question No Corr. answer Question No Corr. answer Question No Corr. answer

58 .) A B C 79 .) A B C

59 .) A B C 80 .) A B C

60 .) A B C

61 .) A B C

62 .) A B C

63 .) A B C

64 .) A B C

65 .) A B C

66 .) A B C

67 .) A B C

68 .) A B C

69 .) A B C

70 .) A B C

71 .) A B C

72 .) A B C

73 .) A B C

74 .) A B C

75 .) A B C

76 .) A B C

77 .) A B C

78 .) A B C

Printed: 19. september 2013 Page 2 of 2

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

Exam ref.:
Basic09.2013-M07-B1-B-1
1.) Trough the control hole on push rod we can:
a) check thread
b) safety wire
c) lock push rod
2.) The unit - bore system is used for:
a) lifting equipment
b) precision mechanics
c) airplanes
3.) Antifriction bearings have raceway made from:
a) chromium nickel steel
b) lead tin alloys
c) cast iron
4.) The allowable wear of the cable could be found in:
a) SRM chapter 51
b) AMM chapter 20
c) AMM chapter 27
5.) Which of the following is the most satisfactory extinguishing agent
for use on a carburator or intake fire?
a) dry chemical
b) a fine, water mist
c) carbon dioxide
6.) When starting and ground operating an aircraft's engine, the
aricraft should be positioned to head into the wind primarily
a) to aid in acheivineg and maintenaning the proper air and
fuel mixture flow in the engine
b) to help cancel out engine torque effect
c) for engine cooling purposes
7.) A fiber type, self locking nut must never be used on an aircraft if
the bolt is
a) under shear loading
b) under tension loading
c) subject to rotation

Printed 19. september 2013 Page 1 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

8.) A certain aircraft bolt has an overall length of 1-1/2 inches, with a
shank length of 1-3/16 inches, and a threaded portion length of 5/8
inch. What is the grip length?
a) .5625 inch.
b) .8750 inch.
c) .3125 inch.
9.) What is descriptive of the annealing process of steel during and
after it has been annealed?
a) rapid cooling; high strength
b) slow cooling; low streangth
c) slow cooling; increased resistance to wear
10.) Why is plastic surface flushed with fresh water before it is cleaned
with soap and water?
a) to prevent crazing
b) to prevent scratching
c) to prevent discoloration
11.) Making MS fitting assembly:
a) the sleeve is re-used to reduce cost
b) flare serves as sealing surface
c) the sleeve is never re-used to reduce cost
12.) Corrosion should be removed from magnesium parts with a:
a) silicon
b) carborundum abrasive
c) stiff, nonmetallic brush
13.) On a fillet weld, the penetration requirement includes what
percentage(s) of the base metal thickness?
a) 100 percent
b) 25 to 50 percent
c) 60 to 80 percent
14.) Why it is considered good practise to normalize a part after
welding?
a) to relive internal stresses developed within the base metal
b) to increase the hardness of the weld
c) to remove the surface scale formed during welding

Printed 19. september 2013 Page 2 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

15.) Unless otherwise specified or required, aircraft bolts should be

installed so that the bolthead is
a) upward, or in a forward direction
b) downward, or in a forward direction
c) downward, or in a rearward direction
16.) What precision measuring tool is used for measuring crankpin and
main bearing journals for out of round wear?
a) dial gauge
b) micrometer caliper
c) depth gauge
17.) If it is necessary to accurately measure the diameter of a hole
approximately 1/4 inch in diameter, the mechanic should use a
a) telescopic gauge and determine the size of a hole by taking
a micrometer reading of adjustable end of the telescopic
gauge
b) 0 to 1 inch inside micrometer and read the measurement
directly from the micrometer
c) small hole gauge and determine the isze of the hole by
taking micrometer reading of the ball end of the gauge
18.) Which tool can be used to measure the alignment of a rotor shaft
or the plane of rotation of a disk
a) dial indicator
b) shaft gauge
c) protractor
19.) The side clearences of piston rings are measured with a
a) micrometer caliper gauge
b) thickenss gauge
c) dial gauge
20.) What is a master type of the manual
a) It is valid only for one operator's fleet
b) It contains all possible configurations of one operator
c) It contains all possible configurations of all operators
21.) What is repairable damage
a) This is a damage, still repairable according to approved
data
b) This is a damage repairable only with part replacement
c) This is a damage, which needs only minor repair.

Printed 19. september 2013 Page 3 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

22.) If found damage is out of tolerance, according to the SRM:

a) Operator makes a repair contacting local civil aviation
authorities
b) Operator makes a repair using its own previous experience
c) Operator makes a repair contacting manufacturer, who
cares also for repair approval
23.) Which is the meaning of the expression BLUE PRINT
a) Copy of the drawing of blue color
b) Copy of the drawing released for production
c) Copy of the drawing, based on which manufacturer makes
aircraft
24.) WHAT ARE THE MOST COMMON STANDARDS IN AVIATION?
a) MS, NAS, AN
b) DIN
c) EACH MANUFACTURER USES ITS OWN STANDARDS
25.) Blue print is usually used for:
a) Only one Part number
b) For many parts of similar system and purpose
c) For one ATA subsystem
26.) Which is purpose of zoning on drawings?
a) To identify locations on drawing
b) To optimize use of space on drawings
c) To utilize different scales, used on drawing
27.) SPECIFICATION OF THE AVIATION PART IS LESS ACCURATE
DESCRIPTION OF CERTAIN PART THAN STANDARD?
a) YES
b) NO
c) THE AVIATION INDUSTRY DOES NOT USE
SPECIFICATION
28.) Way of proper use for technical manuals is described in:
a) List of effective pages
b) Introduction
c) Table of contents

Printed 19. september 2013 Page 4 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

29.) Which is the content of the specifications part of the Blue print
a) It tells, how to repair aircraft
b) Specifications give references, how the content of the blue
print must be done
c) Specifications specify, which content of the blue print must
be done
30.) Which are parts of production drawing?
a) Header and the drawing
b) Drawing and (computerised) parts list
c) Numerous pages of drawing
31.) What is TSM
a) TSM gives instruction for maintenance to line and base
maintenance of aircraft
b) TSM gives instructions for repair if failure symptoms are
known
c) TSM helps to identify aircraft parts
32.) What is meaning of effectivity in customized manuals
a) It indicates validity for aircraft serial number
b) It indicates use of effective pages
c) It indicates valid pages of the manual for aircraft fleet
number of customer/operator
33.) What is IPC
a) This is catalogue of aircraft parts including any part of LRUs
b) This is catalogue of aircraft parts
c) IPC gives price of any aircraft part
34.) What is the influence of the hole tolerance on the fatigue life of the
structural joint:
a) the hole within tolerance extends the fatigue life
b) the oversize hole extends the fatigue life
c) the hole tolerance does not have any influence on the
fatigue life
35.) Which clearance must have press fit
a) Big
b) Positive
c) Negative

Printed 19. september 2013 Page 5 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

36.) Which is the major disadvantage of swaged fitting assembly?

a) not enough reliable
b) too slow to make
c) not possible to disassemble without destruction
37.) At ISO system of tolerances bigger number at letter means:
a) Higher precision
b) Lower precision
c) Defines position of the tolerance field
38.) The rivets are installed with:
a) clearance fit
b) interference fit
c) transition fit
39.) When installing bonded clamps to support metal tubing:
a) paint removal from tube is not recomended as it will inhibit
corrosion
b) paint clamp and tube after clamp instalation to prevent
corrosion
c) remove paint or anodizing from tube at clamp location
40.) The maximum distance between end fittings to which a straight
hose assembly is to be connected is 50 inches. The minimum hose
length to make such a connection should be
a) 54-1/2 inches
b) 51-1/2 inches
c) 52-1/2 inches
41.) Hydraulic tubing, which is damaged in a localized area to such an
extent that repair is necessary, may be repaired
a) by cutting out the damaged area and utilizing a swaged
tube fitting to join the tube ends
b) only by replacing the entire tubing using the same size and
material as the original
c) by cutting out the damaged section and soldering in a
replacement section of tubing
42.) A certain amount of slack must be left in a flexible hose during
installation because, when under pressure, it
a) expands in length and diameter
b) expands in length and contracts in diameter
c) contracts in length and expends in diameter

Printed 19. september 2013 Page 6 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

43.) Tube installation must:

a) Must be regulary cleaned to find any leakage
b) Does not need special maintenance except regular visual
checks according to maintenance program
c) Is often used as a convenient ladder to access other
components
44.) Flexible lines must be installed with
a) enough slack to allow maximum flexing during operation
b) a slack of at least 10 to 12 percent of the length
c) a slack of 5 to 8 percent of the length
45.) On hoses, the inspection criteria requires:
a) Check according to AMM for permitted damage
b) Removal before next flight, if 4 wires are found broken
c) Hoses are serviceable until they leak
46.) Which is the role of regular greasing at roller bearings
a) To replace corrosion protection of the bearing
b) To restore chemical stability of the grease
c) To wash-away internal pollution and restore lubrication
capability of the grease.
47.) At roller bearing installation:
a) Force for press fit is always transmitted from inner ring to
outer and vice versa
b) Force for press fit is achieved with vice or hammer
c) Force for press fit should never transmitted from inner ring
to outer and vice versa
48.) Worn roller bearing is identified by:
a) louder operation and detection of play between inner and
outer ring
b) by detailed disassembly only
c) increased temperature as the only one detection mean
49.) What may be used to remove corrosion from higely stressed steel
surfaces?
a) Steel wire brushes.
b) Fine grit aluminium oxide.
c) Medium grit carborundum paper.

Printed 19. september 2013 Page 7 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

50.) Select the solvent used to clean acrylics and rubber:

a) aplihatic naphtha
b) methyl ethyl ketone.
c) aromatic naphtha.
51.) When taxiing (or towing) an aircarft, a flashing white light from the
control tower means
a) move clear of the runway/tayiway immediately
b) OK to proceed but use extreme caution
c) return to starting point
52.) Nickel cadmium battery cases and drain surfaces which have been
affected by electrolyte sohuld be neutralized with a solution of:
a) boric acid.
b) sodium bicarbonate.
c) potassium hydroxide.
53.) When taxiing (or towing) an aircarft, a flashing red light from the
control tower means
a) stop and wait for green light
b) move clear of the runway/tayiway immediately
c) return to starting point
54.) When first starting to move an aircraft while taxiing, it is important to
a) test the brakes
b) closely monitor the instruments
c) notify the control tower
55.) When stopping a nosewheel-type airplane after taxiing, the
nosewheel should be left
a) unlocked
b) turned at a small angle
c) pointed straight ahead
56.) Curing composite repair without pressure results to:
a) porous inefficient repair
b) efficient repair
c) partially efficient repair

Printed 19. september 2013 Page 8 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

57.) Bonding jumpers should be designed and installed in such a

manner that they:
a) are not subjected to flexing by relative motion of airframe or
engien components.
b) provide a low electrical resistance in the ground circuit.
c) preent buildup of a static electrical sharge between the
aicrafme and the surrounding atmosphere
58.) Are avonics systems sensitive to lightning strike
a) No
b) Only on older aircraft types
c) Yes
59.) What kind of damage is the most common to the nose gear
attacment fitting after rejected take-off
a) None
b) Overheat
c) Distortion
60.) Flight in volcanic ash event causes
a) Severe maintenance bourden, often with both engines
replacement
b) Does not need particular attention, as it has no impact to
performance of the aircraft
c) Requires external inspection with removal of the ash from
all visible places.
61.) Which are the visible damages after the lightning strike
a) Burnt rivet heads, heat delaminated composite parts, radio
and compass failures
b) Burnt rivet heads, heat delaminated composite parts, dot
burns along fuselage and at all tips
c) Radio and compass failures
62.) Most probable damage on composite parts are:
a) On upper side
b) On attachment points of bonding strips and of static
dicchargers
c) On lower side
63.) A fuel that vaporazes too readily may cause
a) hard starting
b) detonation
c) vapor lock

Printed 19. september 2013 Page 9 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

64.) Holes and a few projecting globules are found in a weld. What
action should be taken?
a) reweld the defective portions
b) remove all the old weld, and reweld the joint
c) grind the rough surface smooth, inspect and reweld all
gaps/holes
65.) Which are typical damage types at hard landing
a) Cracks, pulled apart structure, twisted parts, skin wrinkles
along the most loaded areas, pulled fasteners
b) Cracks, pulled apart structure, pulled fasteners, hand
turning of engines is not possible
c) Hard landing is very hard to detect as there is almost no
visible damages.
66.) Which are the most important parameters to define extent of hard
landing
a) Vertical speed and weight at landing
b) Air speed and Vertical speed
c) Vertical speed and Maximum landing weight
67.) Severe turbulence limiting parametres are:
a) Airspeed, aircraft weight and vertical acceleration
b) Aircraft weight and vertical acceleration
c) Airspeed and vertical acceleration
68.) Inspection after hard landing is consisted of 2 levels. After level 1 is
finished without findings:
a) Level 2 is started
b) Level 2 is not neccessary to be performed
c) Simplified procedure is preferred.
69.) What are Time Controlled Items of the Maintenance Program
a) TCI are maintenance tasks, being performed in regular
intervals
b) TCI are parts, which must be discarded or overhauled in
regular intervals
c) TCI are monitors of the time, aircraft stays in maintenance
70.) Who will assure that maintenance of certain check is made
according to the quality standards?
a) Quality assurance
b) Maintenance and its release to service personell
c) Engineering

Printed 19. september 2013 Page 10 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

71.) Which is the purpose of Maintenance Planning Dept. in the air

carrier's Engineering
a) It defines work packages for Aircraft Maintenace, assures
on time accomplisment of tasks from Maintenance
Program and does Record Keeping
b) It defines work packages for Aircraft Maintenace, performs
reliability function and does Record Keeping
c) It plans only the tasks from Maintenance Program.
72.) Which items are listed in Minimum Equipment List?
a) MEL lists allowed dispatch permissions with unserviceable
systems / parts of the aircraft
b) MEL lists all aircraft systems and defines their minimum
function
c) MEL lists allowed dispatch permissions with serviceable
systems / parts of the aircraft
73.) Is accomplishment of Additional Works part of the Maintenance
Program mandatory or optional?
a) They are optional when MP is created, but when they are
part of it, they are mandatory.
b) They are optional
c) They are mandartory.
74.) Unless otherwise specified, torque values of tightening aircraft nuts
and bolts relate to
a) clean, dry threads
b) clean, lightly oiled threads
c) either dry or lightly oiled threads
75.) Is Maintenance Program as document available to mechanics,
doing maintenance
a) Yes, as they read instructions for work from it.
b) Yes, bit only for mandatory part of it
c) No, as work is performed according to the Job Instruction
Cards
76.) Which condition indicates a part has cooled to quickly after being
welded
a) cracking adjacent to the weld
b) discoloration of the base material
c) gas pockets, porosity, and slag inclusions

Printed 19. september 2013 Page 11 of 12

 BASIC09.2013-M07-B1-B-1
Part 147 approved training organization

77.) If Airworthiness Directive is not fulfilled:

a) AD is for information only.
b) The aircraft can fly if permitted by the Civil Aviation
Authority where aircraft is registred
c) The aircraft can't fly in any case
78.) What is Maintenance Review Board Document
a) MRB contains text of the maintenance Job Cards
b) MRB is result of MSG3 analysis of the required
maintenance checks and inspections. Analysis compares
all aircraft system functions and consequences if they fail.
c) MRB is analysis of the required maintenance checks and
inspections based on aircraft system functions. Its content
is solely based on many years of experience of the
manufacturer.
79.) Which is the purpose of Reliability System in the air carrier's
Engineering
a) It measures efectiveness of the Maintenance Program via
counting Man Hours being spent for maintenance
b) It measures efectiveness of the Maintenance Program via
counting unscheduled maintenance tasks and delays
c) It measures quality of work in the maintenance organization
80.) What is Service Bulletin
a) SB is notification of the aircraft type operator about the
availability of the modification or inspection
b) On base of SB regular maintenance tasks are performed
c) SB is document of the reporting system, with which
operators report defect on airctaft type to manufacturer.

Printed 19. september 2013 Page 12 of 12

Answers Name:
Mark: Date:
Review by:

Exam ref.: BASIC09.2013-M07-B1-B-1

Question No Corr. answer Question No Corr. answer Question No Corr. answer

1 .) A B C 19 .) A B C 37 .) A B C

2 .) A B C 20 .) A B C 38 .) A B C

3 .) A B C 21 .) A B C 39 .) A B C

4 .) A B C 22 .) A B C 40 .) A B C

5 .) A B C 23 .) A B C 41 .) A B C

6 .) A B C 24 .) A B C 42 .) A B C

7 .) A B C 25 .) A B C 43 .) A B C

8 .) A B C 26 .) A B C 44 .) A B C

9 .) A B C 27 .) A B C 45 .) A B C

10 .) A B C 28 .) A B C 46 .) A B C

11 .) A B C 29 .) A B C 47 .) A B C

12 .) A B C 30 .) A B C 48 .) A B C

13 .) A B C 31 .) A B C 49 .) A B C

14 .) A B C 32 .) A B C 50 .) A B C

15 .) A B C 33 .) A B C 51 .) A B C

16 .) A B C 34 .) A B C 52 .) A B C

17 .) A B C 35 .) A B C 53 .) A B C

18 .) A B C 36 .) A B C 54 .) A B C

Printed: 19. september 2013 Page 1 of 2

Exam ref.: BASIC09.2013-M07-B1-B-1
Question No Corr. answer Question No Corr. answer Question No Corr. answer

55 .) A B C 75 .) A B C

56 .) A B C 76 .) A B C

57 .) A B C 77 .) A B C

58 .) A B C 78 .) A B C

59 .) A B C 79 .) A B C

60 .) A B C 80 .) A B C

61 .) A B C

62 .) A B C

63 .) A B C

64 .) A B C

65 .) A B C

66 .) A B C

67 .) A B C

68 .) A B C

69 .) A B C

70 .) A B C

71 .) A B C

72 .) A B C

73 .) A B C

74 .) A B C

Printed: 19. september 2013 Page 2 of 2