Ae68 Ae117 J16

ROLL NO.
___________________
Code: AE68/AE117
Subject: EMBEDDED SYSTEMS DESIGN
AMIETE ET (Current & New Scheme)

Time: 3 Hours
June 2016
Max. Marks: 100
PLEASE WRITE YOUR ROLL NO. AT THE SPACE PROVIDED ON EACH PAGE
IMMEDIATELY AFTER RECEIVING THE QUESTION PAPER.
NOTE: There are 9 Questions in all.
Question 1 is compulsory and carries 20 marks. Answer to Q.1 must be written in
the space provided for it in the answer book supplied and nowhere else.
The answer sheet for the Q.1 will be collected by the invigilator after 45 minutes of
the commencement of the examination.
Out of the remaining EIGHT Questions answer any FIVE Questions. Each
question carries 16 marks.
Any required data not explicitly given, may be suitably assumed and stated.
Q.1
Choose the correct or the best alternative in the following:
(2 10)
a. Which one among the following is the fastest form of memory

(A) Random Access Memory (RAM)
(C) Cache memory
(B) Read only memory (ROM)

(D) CD ROM
b. An N-bit memory bus can access

(A) N2 memory locations
(C) Nx2 memory locations
(B) 2N memory locations

(D) 2N/N memory locations
c. The combinational logic expression C=

(A) A+B
(C) B
after reducing becomes
(B) A
(D) Cant be reduced further
d. What is the function of watchdog timer?

(A) The watchdog Timer is an external timer that resets the system if the
software fails to operate properly.
(B) The watchdog Timer is an internal timer that sets the system if the software
fails to operate properly.
(C) The watchdog Timer is an internal timer that resets the system if the
software fails to operate properly
(D) None of these
e. In rate monotonic scheduling
(A) shorter duration job has higher priority
(B) longer duration job has higher priority
(C) priority does not depend on the duration of the job
(D) None of these
AE68/AE117 / June 2016
ROLL NO. ___________________
Code: AE68/AE117
f. In a vectored interrupt
(A) the branch address is assigned to a fixed location in memory
(B) the interrupting source supplies the branch information to the processor
through an interrupt vector
(C) the branch address is obtained from a register in the processor
(D) None of these
g. What will be the affect of following instructions on PSW of 8051
MOV A, #38H
ADD A, #2FH
(A) CY=0, AC=1, P=1
(C) CY=1, AC=0, P=1
(B) CY=0, AC=1, P=0

(D) CY=1, AC=1, P=0
h. VLIW stands for

(A) Very Large Instruction Word
(C) Very Large Instruction Write
(B) Very Long Instruction Word

(D) Very Large Input Words
i. The pipelining process is also called as ______

(A) Superscalar operation
(C) Von neumann cycle
(B) Assembly line operation

(D) None of these
j. The process which has just terminated but has yet to relinquish its resource is
called
(A) Suspended process
(C) Blocked process
(B) Zombie process

(D) Terminated process
Answer any FIVE Questions out of EIGHT Questions.

Each question carries 16 marks.
Q.2
a. What is embedded system?

embedded systems.
List and define three main characteristics of

(8)
b. Given the following three cache designs, find the one with the best
performance by calculating the average cost of access. Show all calculations.
(i) 4 Kbyte, 8-way set associative cache with a 6% miss rate; cache hit costs
one cycle, cache miss costs 12 cycles.
(ii) 8 Kbyte, 4-way set-associative cache with a 4% miss rate; cache hit costs
two cycles, cache miss costs 12 cycles.
(iii) 16 Kbyte, 2-way set-associative cache with a 2% miss rate; cache hit costs
three cycles, cache miss costs 12 cycles.
(8)
Q.3
a. Explain the flow of Development environment of Software and hardware for

Embedded system design.
(10)
b. Discuss the factors for selection of DSP processor for Embedded System. (6)
AE68/AE117 / June 2016
ROLL NO. ___________________
Code: AE68/AE117
Q.4
a. Given a timer structured as in Figure-1(a) and a clock frequency of 10 MHz:
Figure-1(a)
Figure-1(b)
(i) Determine its range and resolution.

(ii) Calculate the terminal count value needed tomeasure 3 ms intervals.
(iii) If a prescaler is added, what is the minimum division needed to measure
an interval of 100 ms? (Divisions should be in powers of 2) Determine this
designs range and resolution.
(iv) If instead of a prescaler a second 16-bit up-counter is cascaded as in
Figure-1(b), what is the range and resolution of this design?
(8)
b. Write a short note on UART and Watch Dog timer.
Q.5
(8)
a. Briefly define each of the following: mask-programmed ROM, EPROM,

EEPROM, flash EEPROM, RAM, SRAM, DRAM, and NVRAM.
(8)
b. Discuss the Cache mapping techniques and Cache Replacement Policy in
detail.
(8)
Q.6
a. Explain Peripheral to memory transfer with DMA controller.

b. Write a Short Note on Controller Area Network (CAN).
Q.7
Q.8
Q.9
(10)
(6)
a. When is an RTOS necessary and when is it not necessary in embedded

systems?
(8)
b. Write short notes on the followings:
(i) Pre-emptive and Non pre-emptive task scheduler
(ii) Semaphore
(8)
a. Explain the Memory Management in RTOS For Embedded Systems.
(8)
b. Write short notes on the followings:

(i) Pipes
(ii) Message Queues
(iii) Shared Memory
(8)
a. What are the rules for interrupt routines in RTOS environment?
(6)
b. Explain different scheduling algorithms in RTOS.
AE68/AE117 / June 2016
(10)

Ae68 Ae117 J16

Uploaded by

Copyright:

Available Formats

Ae68 Ae117 J16

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ae68 Ae117 J16

Uploaded by

Copyright:

Available Formats

ROLL NO.

Subject: EMBEDDED SYSTEMS DESIGN

AMIETE ET (Current & New Scheme)

Max. Marks: 100

Choose the correct or the best alternative in the following:

a. Which one among the following is the fastest form of memory

(B) Read only memory (ROM)

b. An N-bit memory bus can access

(B) 2N memory locations

c. The combinational logic expression C=

after reducing becomes

d. What is the function of watchdog timer?

AE68/AE117 / June 2016

AMIETE ET (Current & New Scheme)

ROLL NO. ___________________

Subject: EMBEDDED SYSTEMS DESIGN

(B) CY=0, AC=1, P=0

h. VLIW stands for

(B) Very Long Instruction Word

i. The pipelining process is also called as ______

(B) Assembly line operation

(B) Zombie process

Answer any FIVE Questions out of EIGHT Questions.

a. What is embedded system?

List and define three main characteristics of

a. Explain the flow of Development environment of Software and hardware for

AE68/AE117 / June 2016

AMIETE ET (Current & New Scheme)

ROLL NO. ___________________

Subject: EMBEDDED SYSTEMS DESIGN

a. Given a timer structured as in Figure-1(a) and a clock frequency of 10 MHz:

(i) Determine its range and resolution.

a. Briefly define each of the following: mask-programmed ROM, EPROM,

a. Explain Peripheral to memory transfer with DMA controller.

a. When is an RTOS necessary and when is it not necessary in embedded

a. Explain the Memory Management in RTOS For Embedded Systems.

b. Write short notes on the followings:

a. What are the rules for interrupt routines in RTOS environment?

b. Explain different scheduling algorithms in RTOS.

AE68/AE117 / June 2016

AMIETE ET (Current & New Scheme)

You might also like