Scribd Logo
Upload

Welcome to Scribd!

  • 737 views

    Isometric Drawing PDF

    Uploaded by

    Velijun R. Perez

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Isometric Drawing PDF

    Uploaded by

    Velijun R. Perez
    737 views16 pages

    Original Title

    Isometric Drawing.pdf

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    737 views16 pages

    Isometric Drawing PDF

    Uploaded by

    Velijun R. Perez

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 16

    CHAPTER 6

    adzlyanuar 2004

    Isometric Drawing

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.1 Pictorial projection


    Not intended to give
    exact or true view.
    Not intended to
    transmit dimensions,
    although sometimes
    dimension is useful.
    Useful when the
    information and
    instructions to be
    given to nontechnical and
    untrained people.
    Hidden lines are not
    shown in isometric
    drawing.

    adzlyanuar 2004-2005

    Pictorial projection:

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.2 Isometric projection

    adzlyanuar 2004-2005

    Isometric projection is a true representation of the


    isometric view of an object
    Isometric view is created by rotating the object 45
    degree about vertical axis, and tilting it forward 35
    deg 16

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.2 Selection of Isometric Axes

    adzlyanuar 2004-2005

    Main purpose of isometric view is to provide a pictorial view


    which reveals as much detail as possible
    Selection of principal edges is important
    Figure shows different isometric views of the same block

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.2 Isometric projection: scale

    adzlyanuar 2004-2005

    The tilt causes the edges & planes to


    become foreshortened
    The projected length is approximately 80%
    of the true length

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.2 Isometric projection & drawing


    Isometric projection & Isometric drawing

    adzlyanuar 2004-2005

    Isometric projection: drawn at scale of 0.816


    Isometric drawing: drawn at full scale

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.3 Iso
    Iso--circles and arcs

    adzlyanuar 2004-2005

    Isometric circles or iso-circle cannot be


    simply drawn using compass.
    Any iso-circle may lie on either top plane,
    left (front) plane or right (profile) plane.
    Iso-circle looks slightly oval and skewed.

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.3 Drawing isoiso-circles


    5
    2

    1
    6

    (a)

    To draw an iso-circle,
    on left plane, Diameter
    20mm

    (b)

    (c)

    (f)

    adzlyanuar 2004-2005

    7
    (a) Draw centre lines,
    vertical & 30deg to left.
    (b) Draw (construction line)
    6
    8
    4
    20mm square box.
    (e)
    The centre lines should
    (d)
    divide each side by half.
    (c) Draw straight lines; 1-2 & 1-3 and 2-5 & 2-6.
    (d) Point 7 is the intersection between line 1-2 & 2-5, and similarly point 8, 1-3 & 2-6 on
    the other side.
    (e) Set your compass to the distance 7-2, draw an arc with centre at point 7, from point 2
    to point 5. Do the same on the other side.
    (f) Set your compass to the distance 1-2, draw an arc with centre (1), from (2) to (3).

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.3 Irregular curves in isometric

    adzlyanuar 2004-2005

    Irregular curves in
    isometric are
    produced by
    transferring the
    coordinates from
    orthogonal view.
    A fixed distance is set,
    A, and the distance in
    B direction are
    obtained.
    These values are then
    transferred to the
    isometric view.

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.4 Producing Isometric drawing

    adzlyanuar 2004-2005

    Read the orthogonal drawing carefully,


    observe the scale,
    choose the best point where isometric axes
    meet to reveal as much detail as possible
    draw an 'isometric box' enclosing the object
    draw in light construction lines
    draw arc & curves in thick, remove excess..
    line in 30 right lines
    line in 30 left lines
    line in vertical lines to complete the view

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    Read multi-view dwg


    given.
    Observe scale,
    dimension, proj. angle
    Determine front, side &
    top view.
    Try to visualise how the
    object looks like.
    Start with sketching, do
    not draw straight away.
    If not sure, start with
    sketching an isometric
    box, enclosing the
    whole object.
    You can label points,
    lines and surfaces on
    multi-view to help
    visualisation.

    adzlyanuar 2004-2005

    6.4 Producing Isometric drawing

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.4 Producing Isometric drawing

    adzlyanuar 2004-2005

    You can start drawing,


    once youre able to
    visualise how the object
    looks like, or finish
    sketching.
    Start with drawing
    construction line
    draw the iso-box, and
    fill up with other lines.
    Line in (darken) arcs &
    circles.

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.5 Isometric dimensions

    adzlyanuar 2004-2005

    Although isometric drawing is not intended


    to transmit dimension, sometimes
    dimensions are placed to indicate the size.
    Two types:

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    6.5 Isometric features


    Common feature shown in isometric drawing.
    Screw thread (external)
    Fillet and rounds

    adzlyanuar 2004-2005

    Isometric section view

    MEMB113 | MANUAL DRAWING | CHAPTER 6

    adzlyanuar 2004-2005

    6.5 Isometric assembly: 3D render

    End of Chapter 6

    adzlyanuar 2004

    THANK YOU

    You might also like