Scribd
Upload
413 views2 pages

Multiple Propagation Resistivity

The document provides technical specifications for Baker Hughes' 2-3/8" and 3-1/8" Multiple Propagation Resistivity (MPR) tools used for formation evaluation in slimhole applications. It details the tool dimensions, operating limits, sensor specifications, and capabilities of providing real-time resistivity measurements to enable geo-steering.

Uploaded by

Qiang Zhang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
413 views2 pages

Multiple Propagation Resistivity

The document provides technical specifications for Baker Hughes' 2-3/8" and 3-1/8" Multiple Propagation Resistivity (MPR) tools used for formation evaluation in slimhole applications. It details the tool dimensions, operating limits, sensor specifications, and capabilities of providing real-time resistivity measurements to enable geo-steering.

Uploaded by

Qiang Zhang
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 2

Technical Data S ummary

2-3/8" & 3-1/8" MPR


Baker Hughes provides the industry with state
of the art Multiple Propagation Resistivity
(MPR) services in 2-3/8" and 3-1/8" toolsize
for slimhole applications, covering hole sizes
from 3" to 5-7/8".
The industry unique 2-3/8" MPR sub was
designed to be utilized with the CoilTrak
system on coiled tubing re-entry drilling
application.

The MPR subs feature a compensated, dual


frequency, dual transmitter / two receiver array
that provides a total of four quantitative
resistivities. The traditional 2 MHz operating
frequency offers excellent vertical resolution
for defining thin beds. The unique 400 kHz
frequency enables deeper formation
investigation for reservoir navigation
applications and provides greater immunity to
environmental and formation effect.

The 3-1/8" MPR sub can be utilized in three


different drilling and MWD systems, the
standard NaviTrak MWD system, the
Advanced Slim MWD system and also the
CoilTrak CT Drilling system. The mechanical
and electrical integration is supported by
system specific upper and lower adapter subs
connected to the main MPR body.
When added to the corresponding BHA
strings, mainly in intermediate radius re-entry
applications but also for standard slimhole
drilling operation, the MPR subs provide realtime formation evaluation services and geosteering capabilities to improve wellbore
placement.

Features

Benefits

Slim design with 2-3/8" and 3-1/8" tool OD

Ideal for slimhole re-entry and/or throughtubing wellbore construction

Utilizes 2 MHz and 400 kHz transmitted


frequencies for resistivity measurement

Operates and provides FE capability in all


mud types

Rugged, integral antenna design and fully


digital electronics

High reliability and BUR capability

Provides real-time data transmitted to surface


via system related e-line or mudpulse
telemetry

Geo-steering service for optimized wellbore


placement

2-3/8" & 3-1/8" MPR

2011-2011 Baker Hughes Incorporated. All rights reserved.


MPR-70-01-001 Rev. A

Technical Data S ummary

2-3/8" & 3-1/8" MPR


General Tool Specifications
Tool OD
Borehole Size Range
Minimum Push Thru Restriction
Length of Tool incl. Adapter Subs
CoilTrak Setup
Advanced Slim MWD
NaviTrak (refer to special TDS for NTK setup)
Weight of Tool incl. Adapter Subs
CoilTrak Setup
Advanced Slim MWD
NaviTrak (refer to special TDS for NTK setup)
Tool Connections Up / Down
Telemetry Type

SI Units

US Units

SI Units

US Units

60 mm
76 mm - 89 mm
70 mm

2-3/8"
3" - 3-1/2"
2-3/4"

80 mm
95 mm - 149 mm
--

3-1/8"
3-3/4" - 5-7/8"
--

2,9 m
---

9.5 ft
---

3,92 m
3,99 m
5,20 m

12.85 ft
13.09 ft
17.00 ft

55 kg
121 lbs
116 kg
256 lbs
--118 kg
260 lbs
--129 kg
284 lbs
2-3/8" HDI Box / Pin with wet connect
3" CDP Box / Pin with wet connect
E-line or mud pulse using BCPM / NaviTrak

Operating Specifications and Limits

SI Units

US Units

SI Units

Tool OD
Max. Flow Rate
Max. Operating Temperature
Max. Hydrostatic Pressure
Max. Differential Pressure
Max. WOB or Compressive Load
Max. Drilling Torque
Max. Overpull to Failure (w/o Rotation)
RPM

60 mm
300 lpm
150C
1000 bar
300 bar
39 kN
-100 kN

2-3/8"
80 gpm
302F
14,500 psi
4,300 psi
8,800 lbs
-22,450 lbs

80 mm
3-1/8"
600 lpm
160 gpm
150C
302F
1380 bar
20,000 psi
300 bar
4,300 psi
45 kN
10,000 lbs
1600 Nm
1,180 ft-lbs
260 kN
58,500 lbs
400 (dependent on BHA system / configuration)

--

80% Max. deviation from mean RPM (e.g. 100 RPM: RPM Range=20-180),
limited by maximum tool rotation specification, (from recorded memory or as flagged by corresponding real-time severity level)

Max. RPM Variation


Max. DLS
Rotating
Sliding
Sand Content
LCM
Max. Axial & Lateral Vibration
Sensor Specifications
MPR
Range
Accuracy
Vertical Resolution
Downhole End to Measure Point
CoilTrak Setup
Advanced Slim MWD
NaviTrak (refer to special TDS for NTK setup)

Drilling & Evaluation


2001 Rankin Road
Houston, Texas 77073
Phone: +1 713-625-4200
www.bakerhughes.com

US Units

-50/30 m

-12/30 m
12/100 ft
50/100 ft
50/30 m
50/100 ft
1% max. volume, acc. to API 13B (< 0.5% recommended)
Fine to medium nut plug (15 lbs/bbl). (Any pumping of LCM must be carried out according to INTEQ procedure)
Refer to Supplemental Technical Specification document TDS-20-60-0000-00

SI Units

US Units

2 MHz Resistivity
Phase Difference
Attenuation
(long spaced)
(long spaced)
0.1 - 3000 ohm-m
0.1 - 500 ohm-m
1% (0.1 - 50 ohm-m)
2% (0.1 - 25 ohm-m)
0.5 mS/m (>50 ohm-m)
1.0 mS/m (>25 ohm-m)
30 cm (12") for 90 % response in conductive beds
1,19 m
---

3.91 ft
---

SI Units

US Units

400 kHz Resistivity


Phase Difference
Attenuation
(long spaced)
(long spaced)
0.1 - 1000 ohm-m
0.1 - 200 ohm-m
1% (0.1 - 25 ohm-m)
5% (0.1 - 10 ohm-m)
1.0 mS/m (>25 ohm-m)
5.0 mS/m (>10 ohm-m)
30 cm (12") for 90 % response in conductive beds
1,60 m
1,67 m
2,80 m

5.24 ft
5.48 ft
9.30 ft

Although the information contained herein is believed to be accurate, no other representations are made concerning the information. Under no circumstances shall Baker Hughes be liable for any incorrect or incomplete
information. All technical specifications and commercial information concerning the product and/or services described herein may be changed at any time without further notice. Refer to Supplemental Technical Specifications
(TDS-20-60-0000-00) for further environmental specific specifications and information on the application, operation, and handling of Baker Hughes tools. Technical Data Summaries are controlled documents and can only be
released through the Documentation & Records Management System(s) Group.
MPR-70-01-001

You might also like