Deicon: Active, Feedback-Controlled Induction Noise Abatement

Active, Feedback-Controlled Induction Noise Abatement
DEICONs active, low-frequency, electronic acoustic absorber can be configured to act as an acoustic dynamic
absorber, and be used in forced noise control applications such as induction noise abatement.
Reactive absorbers, such as Helmholtz resonators (HR) or quarter-wave tubes, are commonly used as the most
effective solution for abating the low-frequency noise in many applications including induction systems,
particularly in luxury cars. The problem with these low-frequency absorbers is their large size. In addition,
reactive absorbers can only be tuned to a single frequency. When absorption at multiple frequencies is required, a
number of these absorbers tuned to different frequencies should be used. Accommodating a large number of
these resonators under the hood (luxury vehicles may use multiple resonators) is a packaging challenge, not to
mention expensive. Active noise control would enable automakers to eliminate the need for resonators. It allows
one to deal with multiple frequencies using only a single system.
Active noise control systems normally consist of a microphone, another sensor to identify the targeted frequencies
(e.g., the engine rpm sensor), an electronic controller, and a speaker mounted at a vehicle's air induction system.
The signals measured by the microphone and the 2nd sensor are processed by the controller (algorithm) creating
the control signal which will drive the speaker. The active system is small and does not cause under-hood
packaging problems. Most active control systems use feedforward, Least Mean Square (LMS) based adaptive
algorithms as their controllers. These complex algorithms need fast, powerful digital signal processors to run. To
ensure the convergence of the algorithm, the rate of adaptation should be made slow. This might create the loss of
effectiveness of the controller during the transients, e.g., a fast run up of the engine. Although these adaptive
feedforward algorithms have been around for more than 20 years, i.e., since the creation of DSPs, but their
complexity and cost have prevented them from finding a place in auto industry.
DEICONs cost-effective, feedback-based active noise control scheme, configured as a dynamic absorber, to
abate the low frequency induction noise. The controller is realized by a low-cost, adaptable, op-amp circuit can
be tuned to a single or multiple frequencies abates the sound at that (those) frequencies. A microphone, nearly
collocated with the actuator, is used for sensing. Adaptation can be done by constant, automatic retuning of the
controller to the engine rpm.
The added benefit of all active induction noise control system is that they could enable automotive engineers to
shape a vehicle's noise signature to the image of the vehicle, for example powerful, sporty or nostalgic.
pressure/voltage
-10
uncontrolled
controlled
-20
-30
Scaled Mag, dB
In a lab-scale set up, resembling the induction system of a

4 cylinder engine, the effectiveness of the active feedback
controlled noise abatement system is evaluated. The set
up consists of a short 28 inch plastic tube with the
diameter of 4. One end of the tube is equipped with a
4 speaker (noise speaker resembling the engine cylinder)
that excites the system. The control speaker (another 4
cone) and microphone are installed in the middle of tube
(in the filter box).
-40
-50
Figure 1 shows the frequency response functions

-60
mapping the voltage driving the noise speaker to the
pressure measured at the tube outlet, with (red/solid line)
-70
indcuc.m
and without (blue/dashed line) control. The active
-80
control system, which is designed to absorb tones at 100,
50
100
150
200
250
300
350
400
Freq, Hz
150, and 200 Hz, is performing effectively. Clear from
Figure 1, the transmission of these tones from the noise
Figure 1 Frequency response functions mapping the
speaker (cylinder) to the air intake opening is hindered.
pressure at the tube inlet to the voltage driving the
This work demonstrates the feasibility of such a cost noise speaker
effective active noise control system.
DEICON
DYNAMICS & CONTROLS
WWW.DEICON.COM
[email protected]
(937) 885 4134

Deicon: Active, Feedback-Controlled Induction Noise Abatement

Uploaded by

Copyright:

Available Formats

Deicon: Active, Feedback-Controlled Induction Noise Abatement

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Deicon: Active, Feedback-Controlled Induction Noise Abatement

Uploaded by

Copyright:

Available Formats

Active, Feedback-Controlled Induction Noise Abatement

In a lab-scale set up, resembling the induction system of a

Figure 1 shows the frequency response functions

(937) 885 4134

You might also like