Scribd
Upload
117 views6 pages

Body Composition Arduino Code

This document defines constants and functions for programming an AD5933 impedance analyzer chip over I2C. It includes: 1. Constants for register addresses and configuration values like start frequency and increment. 2. Functions for writing and reading registers to program the chip, run impedance sweeps, and measure temperature. 3. A setup function that initializes I2C and programs default register values. The main loop reads serial commands to program registers, run sweeps, and measure temperature by calling the corresponding functions.

Uploaded by

José A. Álvarez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
117 views6 pages

Body Composition Arduino Code

This document defines constants and functions for programming an AD5933 impedance analyzer chip over I2C. It includes: 1. Constants for register addresses and configuration values like start frequency and increment. 2. Functions for writing and reading registers to program the chip, run impedance sweeps, and measure temperature. 3. A setup function that initializes I2C and programs default register values. The main loop reads serial commands to program registers, run sweeps, and measure temperature by calling the corresponding functions.

Uploaded by

José A. Álvarez
Copyright
© © All Rights Reserved
We take content rights seriously. If you suspect this is your content, claim it here.
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 6

#include "Wire.

h"
#define button 2
#define SLAVE_ADDR 0x0D
#define ADDR_PTR 0xB0
#define START_FREQ_R1 0x82
#define START_FREQ_R2 0x83
#define START_FREQ_R3 0x84
#define FREG_INCRE_R1 0x85
#define FREG_INCRE_R2 0x86
#define FREG_INCRE_R3 0x87
#define NUM_INCRE_R1 0x88
#define NUM_INCRE_R2 0x89
#define NUM_SCYCLES_R1 0x8A
#define NUM_SCYCLES_R2 0x8B
#define RE_DATA_R1 0x94
#define RE_DATA_R2 0x95
#define IMG_DATA_R1 0x96
#define IMG_DATA_R2 0x97
#define TEMP_R1 0x92
#define TEMP_R2 0x93
#define CTRL_REG 0x80
#define CTRL_REG2 0x81
#define STATUS_REG 0x8F
const float MCLK = 16.776*pow(10,6); // AD5933 Internal Clock Speed 16.776 MHz
const float start_freq = 1*pow(10,3); // Set start freq, < 100Khz
const float incre_freq = 1*pow(10,2); // Set freq increment
const int incre_num = 90; // Set number of increments; < 511
char state;
void setup() {
Wire.begin();
Serial.begin(115200);
pinMode(button, INPUT);
//nop - clear ctrl-reg
writeData(CTRL_REG,0x0);
//reset ctrl register
writeData(CTRL_REG2,0x10);
programReg();
}
void loop(){
//Read state and enter FSM

if(Serial.available()>0) {
state = Serial.read();
//FSM
switch(state) {
case 'A': //Program Registers
programReg();
break;
case 'B': //Measure Temperature
measureTemperature();
break;
case 'C':
runSweep();
delay(1000);
break;
/////Programming Device Registers/////
}
Serial.flush();
}
}

void programReg(){
// Set Range 1, PGA gain 1
writeData(CTRL_REG,0x01);
// Set settling cycles
writeData(NUM_SCYCLES_R1, 0x07);
writeData(NUM_SCYCLES_R2, 0xFF);
// Start frequency of 1kHz
writeData(START_FREQ_R1, getFrequency(start_freq,1));
writeData(START_FREQ_R2, getFrequency(start_freq,2));
writeData(START_FREQ_R3, getFrequency(start_freq,3));
// Increment by 1 kHz
writeData(FREG_INCRE_R1, getFrequency(incre_freq,1));
writeData(FREG_INCRE_R2, getFrequency(incre_freq,2));
writeData(FREG_INCRE_R3, getFrequency(incre_freq,3));
// Points in frequency sweep (100), max 511
writeData(NUM_INCRE_R1, (incre_num & 0x001F00)>>0x08 );
writeData(NUM_INCRE_R2, (incre_num & 0x0000FF));
}
void runSweep() {

short re;
short img;
double freq;
double mag;
double phase;
double gain;
double impedance;
int i=0;
programReg();
// 1. Standby '10110000' Mask D8-10 of avoid tampering with gains
writeData(CTRL_REG,(readData(CTRL_REG) & 0x07) | 0xB0);
// 2. Initialize sweep
writeData(CTRL_REG,(readData(CTRL_REG) & 0x07) | 0x10);
// 3. Start sweep
writeData(CTRL_REG,(readData(CTRL_REG) & 0x07) | 0x20);
while((readData(STATUS_REG) & 0x07) < 4 ) { // Check that status reg != 4, sweep not complete
delay(100); // delay between measurements
int flag = readData(STATUS_REG)& 2;
if (flag==2) {
byte R1 = readData(RE_DATA_R1);
byte R2 = readData(RE_DATA_R2);
re = (R1 << 8) | R2;
R1 = readData(IMG_DATA_R1);
R2 = readData(IMG_DATA_R2);
img = (R1 << 8) | R2;
freq = start_freq + i*incre_freq;
mag = sqrt(pow(double(re),2)+pow(double(img),2));
// phase = atan(double(img)/double(re));
// phase = (180.0/3.1415926)*phase; //convert phase angle to degrees
// Phase Calibration
// sys_phase = 118;
// phase = phase - sys_phase;
//

// gain = (1.0/197760)/9786.98;
impedance = 1/(gain*mag);
Serial.print("Frequency: ");
Serial.print(freq/1000);
Serial.print(",kHz;");
Serial.print(" Magnitude: ");
Serial.print(mag);
Serial.print(",kOhm;");
Serial.print(" Resistance: ");

Serial.print(re);
Serial.print(",");
Serial.print(" Reactance: ");
Serial.print(img);
Serial.println(",");
// break; //TODO: for single run, remove after debugging
//Increment frequency
if((readData(STATUS_REG) & 0x07) < 4 ){
writeData(CTRL_REG,(readData(CTRL_REG) & 0x07) | 0x30);
i++;
}
}
}

//

//Power down
writeData(CTRL_REG,0xA0);
writeData(CTRL_REG,(readData(CTRL_REG) & 0x07) | 0xA0);

void writeData(int addr, int data) {


Wire.beginTransmission(SLAVE_ADDR);
Wire.write(addr);
Wire.write(data);
Wire.endTransmission();
delay(1);
}
int readData(int addr){
int data;
Wire.beginTransmission(SLAVE_ADDR);
Wire.write(ADDR_PTR);
Wire.write(addr);
Wire.endTransmission();
delay(1);
Wire.requestFrom(SLAVE_ADDR,1);
if (Wire.available() >= 1){
data = Wire.read();
}
else {
data = -1;
}
delay(1);
return data;
}

boolean measureTemperature() {
// Measure temperature '10010000'
writeData(CTRL_REG, 0x90);
//TODO: necessary to write to second control register?
delay(10); // wait for 10 ms

//Check status reg for temp measurement available


int flag = readData(STATUS_REG)& 1;
if (flag == 1) {
// Temperature is available
int temperatureData = readData(TEMP_R1) << 8;
temperatureData |= readData(TEMP_R2);
temperatureData &= 0x3FFF; // remove first two bits
if (temperatureData & 0x2000 == 1) { // negative temperature
temperatureData -= 0x4000;
}
double val = double(temperatureData) / 32;
temperatureData /= 32;
Serial.print("Temperature: ");
Serial.print(val);
//Serial.write(176); //degree sign
Serial.println("C.");
// Power Down '10100000'
writeData(CTRL_REG,0xA0);
return true;
} else {
return false;
}
}
byte getFrequency(float freq, int n){
long val = long((freq/(MCLK/4)) * pow(2,27));
byte code;
switch (n) {
case 1:
code = (val & 0xFF0000) >> 0x10;
break;

case 2:
code = (val & 0x00FF00) >> 0x08;
break;
case 3:
code = (val & 0x0000FF);
break;
default:
code = 0;
}
return code;
}

You might also like