Card Reader Manual

9292 Jeronimo Road
Irvine, CA 92618-1905
EntryProx
USER MANUAL
4045-905, Rev C.2
February 7, 2007
2007 HID Global Corporation. All rights reserved.
Part No. 4045-905, Rev C.2
EntryProx User Guide
Contents
1
INTRODUCTION .............................................................. 4
PRODUCT OVERVIEW .................................................... 4
INSTALLATION................................................................ 8
MOUNTING .................................................................... 10
WIRING........................................................................... 23
PROGRAMMING ............................................................ 25
CARD/PIN PROGRAMMING SEQUENCES .................. 30
CHANGING OPERATING PARAMETERS .................... 35
DOWNLOADING DATA TO A PDA ............................... 39
10
DOWNLOADING A TRANSACTION LOG ..................... 43
11
WIEGAND MODE ........................................................... 47
12
PROGRAMMING COMMANDS ..................................... 49
13
LED/SOUNDER STATUS INDICATIONS ...................... 55
List of Figures
Figure 1 Factory Supplied Parts ...................................................... 9
Figure 2 Removing Wiring Exits and Mounting Holes ................... 11
Figure 3 Pulling Wires through the Backplate ............................... 12
Figure 4 Removing the Circuit Board ............................................ 13
Page 2 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
Figure 5 Removing the P4 Connector ........................................... 15

Figure 6 Removing the Antenna Housing...................................... 16
Figure 7 Mounting the Antenna Backplate .................................... 17
Figure 8 Attaching the Antenna Housing ....................................... 18
Figure 9 Filler Piece and Request to Exit Switch ........................... 19
Figure 10 Tamper Switch Installation ............................................ 22
Figure 11 Pin Locator Diagram ..................................................... 23
Figure 12 Transaction Log ............................................................ 44
List of Tables
Table 1 Programming Commands ................................................ 49
Table 2 LED/Sounder Indications .................................................. 55
Version History
Date
Author
Description
Document
Version
020707
LHanna
Reformatted, added correct IP statement
C.2
080706
BHolland
Error correction in EntryProx User Guide

4045-905 C.0 - page 33, add ".com" to
hidcorp URL
C.1
052506
CShea /
Thad
Smith
Added PDA support for logging data.
C.0
February 7, 2007
Page 3 of 58
Part No. 4045-905, Rev C.2
INTRODUCTION
This Users Guide provides information and instructions for
installing, wiring, and programming the EntryProx unit.
IMPORTANT
KEEP A USER LIST when programming cards and PIN

codes into your EntryProx. Write down the User Location,
Card Number, PIN Code and the Name of the User. Use
the blank form in Appendix A as a photocopy master.
CHANGE THE MASTER CODE from the factory default
(User Location 1, PIN Code: 1234) to a new code (1-6
digits). Programming commands will not work until the
default Master Code is changed. Write the new code
down and keep it in a safe place.
PROGRAM THE NEW MASTER CODE INTO LOCATION
0. Once this is done, the default Master Code in User
Location 1 can now be reprogrammed for normal access
control use. The Rev C EntryProx no longer reserves
User Location 1 for the Master Code.
IF YOU LOSE / FORGET THE MASTER CODE
End Users: contact your dealer a service call is
required.
Dealers: call HID Technical Support.
T
CONSIDER A SECURE INSTALLATION if installing on an

exterior door or high-risk location
PRODUCT OVERVIEW
The EntryProx unit provides card and keypad access control for a
single entrance. The unit can be installed in a standard one-stage
configuration or a secure two-stage (remote) configuration.
(Secure installation will be card-only.)
To gain access to the controlled door, the user presents their card
to the reader and / or enters their PIN code into the keypad. The
unit searches its memory for that card or PIN code. If the unit
finds the card or PIN code, it unlocks the door or performs some
other action that has been programmed for that user.
Page 4 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
The EntryProx unit is compatible with all HID proximity access

cards or key tags encoded with up to 37 bits of data. All
programming options are performed using the controller keypad.
Manual or batch card/tag programming via the keypad can be
completed for 26-bit format only. A batch of cards or tags encoded
in any format can be sequentially presented to the reader by
entering a single keypad command.
The Rev C EntryProx can download card and transaction reports
via the IR LED to an optional Palm PDA. Previous product
versions downloaded to a thermal printer.
2.1
UNIT CAPACITY
The EntryProx unit can accommodate up to 2,000 users. Each
user is assigned to a User Location (numbered 1 2000), which
can have a card/key tag, a PIN code, or a card/key tag PLUS a
PIN code. User Location 0 is reserved for the Master Code (used
for programming, only).
2.2
TRANSACTIONS
A maximum of 1,000 transactions can be stored in the EntryProx
unit. Each transaction includes the time, the date, the User
Location and the event. When maximum capacity is reached, the
oldest transactions are overwritten.
2.3
PRE-PROGRAMMING THE UNIT BEFORE

INSTALLATION
Dealers and installers are advised to pre-program the unit at their
offices before installing it at the site. Simply connect it to a 12VDC
source, follow configuration and card enrollment instructions at the
end of this guide, and disconnect the unit. Programming will be
retained in memory. You will spend less time at the site, and by
being familiar with programming, will be able to train the end user
more effectively.
February 7, 2007
Page 5 of 58
Part No. 4045-905, Rev C.2
2.4
SPECIFICATIONS
CATEGORY
REQUIREMENTS
Environmental
Operating Temperature
31F to +150F
(-35C to +66C) @ 30 VDC
Operating Humidity
5% to 95% relative humidity,

non-condensing
Electrical
Power Supply/Current
Requirements
10 - 15V DC, linear, filtered and regulated power

supply recommended 150 mA for the EntryProx
unit only.
Additional capacity or separate supply required for
locking device or peripherals.
Mechanical
Height
5.25 in (13.3 cm)
Width
2.75 in (7 cm)
Depth
1.625 in (4.1 cm)
Relay Outputs
Main Relay, Aux Relay
Form C (switches up to 1A inductive load, 2A

resistive @ 30VDC)
Sounder
4000 Hz, defeatable
LEDs
Bi-Color (red/green)
Amber
Infrared
Page 6 of 58
February 7, 2007
2.5
Part No. 4045-905, Rev C.2
DEFAULT SETTINGS
The EntryProx unit is shipped with the following default settings.
PARAMETER
DEFAULT SETTING
Master Code (User Location 1)
1234*
Code must be changed before programming the

unit.
Main Relay energizes for
5 seconds
Audible Keypress Feedback
ON
Local Propped Door Sounder activates after
30 seconds
Local Forced Door Sounder activates

immediately for
10 seconds
Data Output Port
Infrared (IR) port
February 7, 2007
Page 7 of 58
Part No. 4045-905, Rev C.2
INSTALLATION
You can install the EntryProx unit by using a standard installation
method or a secure installation method. Both installation methods
require that you mount the EntryProx unit to a wall or glass
surface.
3.1
ASSEMBLY PARTS
Before you install the EntryProx, be sure that you have the correct
factory and installer supplied parts.
A. Controller Keypad Unit
I. Silicone Rubber Cushion
B. Controller Keypad
Backplate
J. Self-Adhering Pads
C. Cable Assemblies
K. 2-pin Jumper
D. Antenna Backplate
L. Filler Piece
E. Antenna Housing
M. Lithium Coin Cell Battery (see page

10 for the Battery Caution statement)*
F. Blank Label
G. Mounting Screws
N. Cover screws hex and tamper.*
H. Press to Exit Label
O. Hex wrench*
* - not shown in Figure 1

- pre-installed on main board connector P2, pins 5 & 6
Page 8 of 58
February 7, 2007
Part No. 4045-905, Rev C.2

A
K
L
H
I
B
J
G
F
D
Figure 1 Factory Supplied Parts
3.2
INSTALLER SUPPLIED PARTS LIST
Appropriate DC power supply (10-15VDC, linear type)

Appropriate separate power supply for door locking unit.
Appropriate electrical tools
Recommended remote antenna cable ALPHA 1294C
(22AWG)
Wiegand interface cable ALPHA 1295C (22AWG) (only if
using a separate Wiegand access control panel)
Power supply cable (18AWG - 22AWG)
Door locking unit cable (18AWG - 22AWG)
Door monitor cable (18AWG - 22AWG)
Request to Exit cable (ALPHA 2421C 18AWG or ALPHA
1292C 22AWG) (only if using remote switch)
Optional tamper screw bit (only if tamper screw is used)
Ademco 945T or PR-20451 magnet and reed switch or
equivalent (for UL 294 compliance)
February 7, 2007
Page 9 of 58
Part No. 4045-905, Rev C.2
CAUTION Replace Battery with Panasonic BR1225 only.

Use of another battery may present a risk of fire or
explosion. Battery may explode if mistreated. Do not
recharge, disassemble or dispose of battery in fire.
MOUNTING
If you mount the EntryProx unit to a wall, you can install an
electrical junction box to hold the unit and the wires in place. The
mounting hole cutouts on the backplate line up with the screw
holes on a standard junction box.
If you mount the EntryProx unit to a glass surface, DO NOT
remove the wire exits on the backplate. Remove the appropriate
wire exit cutouts located on each side of the controller keypad
case.
If your installation must comply with the UL 294 Standard

for Access Control, please read Page 14.
4.1
PRECAUTIONS FOR OUTDOOR

INSTALLATIONS
Water damage is a key cause of unit malfunction, causing
corrosion or short circuits. When mounting the unit in an area
that will be exposed to rain or moisture, take the following
precautionary measures:
1. Use silicone to seal wire runs and mounting holes

(antenna is already sealed).
2. Do NOT seal the cover and base together. Water that
enters the case must be allowed to run out at the
bottom.
3. Bend the wires to form a drip loop before they enter the
case. This will prevent water from following the wires
into the case.
Page 10 of 58
February 7, 2007
4.2
Part No. 4045-905, Rev C.2
BEGINNING ENTRYPROX INSTALLATION

To mount the EntryProx unit, referring to Figure 2 and Figure 3,
follow these instructions:
1. Remove the hex screw located at the bottom of the

EntryProx unit.
2. Disconnect the backplate of the EntryProx unit from the
controller keypad.
3. Remove the wire exits and mounting hole cutouts from
the backplate.
4, Pull the wires through the backplate.
5. Attach the backplate to a wall or glass surface using the
mounting screws or the self-adhesive fasteners.
Mounting Hole Cutouts
Wire Exits
Mounting Hole Cutouts
Figure 2 Removing Wiring Exits and Mounting Holes
February 7, 2007
Page 11 of 58
Part No. 4045-905, Rev C.2
Figure 3 Pulling Wires through the Backplate
4.3
CONTROLLER KEYPAD WIRING

In a standard installation, the antenna housing remains installed in
the controller keypad, and the complete unit is installed outside of
the secured area. This is appropriate for interior doors or lowrisk exterior installations.
For compliance with the UL294 Standard, additional installation
requirements must be met see INSTALLATION COMPLIANCE
FOR UL 294, page 20.
To wire the EntryProx unit for a standard installation, refer to
Figure 4 and follow these instructions.
1. Touch a grounded object BEFORE touching the main

circuit board to guard against possible static
discharges.
2. Remove the main circuit board by pushing outward on
the two spring tabs in the direction shown in Figure 4.
3. Lift the main circuit board.
4. Make the wiring connections for the door locking
devices, the power supply, and the alarm inputs and
outputs. Refer to WIRING, page 23 for appropriate
wiring diagrams.
Page 12 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
5. Reattach the main circuit board to the controller keypad

unit.
6. Attach the controller keypad unit to the mounted
backplate and secure the EntryProx unit with a hex
screw or tamper screw.
Note: A ribbon cable holds the main circuit board to the controller
keypad board. DO NOT CUT OR REMOVE this cable from its
connector.
Figure 4 Removing the Circuit Board
February 7, 2007
Page 13 of 58
Part No. 4045-905, Rev C.2
4.4
CONTROLLER KEYPAD WIRING - SECURE

INSTALLATION
In a secure installation, the waterproof antenna housing is
removed from the controller keypad and mounted outside of a
secured area. The control unit is installed inside the secured area.
The blank filler piece is then inserted into the controller keypad in
its place. This is appropriate for exterior doors or medium to
high-risk locations.
To wire the EntryProx unit for a secure installation, refer to Figure
5 and Figure 6 and follow these instructions.
1. Touch a grounded object BEFORE touching the main

circuit board to guard against possible static
discharges.
2. Remove the main circuit board by pushing outward on
the two spring tabs in the direction shown in Figure 4.
3. Lift the main circuit board.
4. Unplug the four-pin cable assembly from connector P4
on the main circuit board.
5. Release the antenna housing from the controller
keypad by pressing inward on the four securing tabs.
6. Remove the antenna housing from the controller
keypad by pushing forward as shown in Figure 6.
7. Insert the extra 10-inch antenna cable assembly into
connector P4.
8. Splice in additional antenna cable Alpha 1174C
(22AWG) up to a maximum of 10 feet.
Note: The Alpha 1174C antenna cable is not supplied with the
EntryProx unit.
Page 14 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
9. Make the wiring connections for the Request to Exit

switch, the door locking devices, the power supply, and
the alarm inputs and outputs. Refer to WIRING, page23
for appropriate wiring instructions.
10. Reattach the main circuit board to the controller keypad
unit.
11. Insert the blank filler piece into the controller keypad
unit.
12. Attach the controller keypad unit to the mounted
backplate and secure the EntryProx unit with a hex
screw or tamper screw.
13. Run the additional antenna cable to the antenna
housing location.
14. Mount and wire the antenna housing
P4 Connector Cable
Assembly
Figure 5 Removing the P4 Connector

February 7, 2007
Page 15 of 58
Part No. 4045-905, Rev C.2
Figure 6 Removing the Antenna Housing
Page 16 of 58
February 7, 2007
4.5
Part No. 4045-905, Rev C.2
ANTENNA HOUSING - SECURE

INSTALLATION
Mount and wire the antenna housing no more than 10 feet away
from the controller keypad unit.
To mount and wire the antenna housing, refer to Figure 7 and
Figure 8 and follow these instructions.
1. Pull the additional antenna cable through the antenna

housings backplate cable holes.
Cable Holes
Moisture Release
Holes
Figure 7 Mounting the Antenna Backplate

2. Position and secure the antenna backplate to the
mounting surface so that the two moisture release
holes are on the bottom.
3. Cut the plastic connector off the antenna cable
assembly.
4. Splice in the additional antenna cable. Be careful to
match the wire colors to the proper pin connectors on
the 10-inch antenna cable assembly.
February 7, 2007
Page 17 of 58
Part No. 4045-905, Rev C.2
5. Attach the antenna housing to the backplate by

inserting the four securing tabs into the backplate.
6. Seal the wire holes with silicone.
4.6
FILLER OR REQUEST TO EXIT LABEL

The filler piece replaces the antenna housing on the controller
keypad when you use the high security installation. If you do not
plan to use the filler piece as a Request to Exit switch:
1. Insert the filler piece into the opening on the controller

keypad.
2. Apply the blank label.
Figure 8 Attaching the Antenna Housing
Page 18 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
If you plan to use the filler piece as a Request to Exit switch:
1. Remove the two plastic side tabs on the filler piece.

2. Insert the silicone rubber cushion over the two
alignment pins on the switch activator.
3. Apply the Press to Exit label to the filler piece.
4. Insert the filler piece into the opening on the controller
keypad.
5. Refer to Figure 11 to make the wiring connections to
the cable assembly if you are using a door contact.
6. Set the internal Request to Exit button ON, using
programming Command 30, option 7 (see Table 1
Programming Commands).
Cushion
Figure 9 Filler Piece and Request to Exit Switch
February 7, 2007
Page 19 of 58
Part No. 4045-905, Rev C.2
4.7
INSTALLATION COMPLIANCE FOR UL

294
The EntryProx Model 4045CGNU0 complies with the UL294
Standard for access control units in a standard, wall-mount
installation, when installed to the following specifications:
4.8
Electric locking mechanisms may only be connected to the

NO contacts of the Main Relay. Locking devices requiring
an NC connection may only be used in conjunction with an
interposing relay mounted inside the secure area and
connected to the NO contacts of the Main Relay.
The recommended or equivalent shielded wiring must be
used for the following applications:
Request to Exit input
cable
Alpha 1292C (22AWG) or 2421C

(18AWG)
Wiegand data output

cable
Alpha 1295C (22AWG)
Antenna cable extension
Alpha 1294C (22AWG)
The cable shield drain wires must be grounded at the

reader end by connection to P1, Pin 4 (DC Power
configurations recommended below) by connection to P1,
Pin 4 (DC Power Ground) using appropriate wire nuts or
crimp fittings.
Tamper Switch must be installed in one of the
configurations recommended below, and connected to an
intrusion alarm system. (Refer to Figure 10 for
switch/magnet locations)
METAL OR PLASTIC SINGLE GANG J-BOX

1. Use an Ademco 945T magnet and reed switch (or
equivalent) with foam-backed adhesive tape.
2. Clip the screw mounting tabs from both the magnet and
reed switch using pliers or a wire cutter.
Page 20 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
3. Remove the backing sheet from the tape on the

magnet and stick the magnet to the plastic spacer,
which is factory-installed to the back of the Keypad
board in location A (Figure 10).
4. Stick the reed switch on the inside of the long side of
the J-box in the upper right-hand corner, using the
adhesive tape. The switch should be flush with the
edge of the J-box.
4.9
WALL MOUNTING
1. Use an Ademco PR-20451 magnet and reed switch
(or equivalent) with foam-backed adhesive tape.
2. Remove the backing sheet from the tape on the
magnet and stick the tape to the plastic spacer, which
is factory-installed to the back of the Keypad board at
location B (Figure 10).
3. Drill a 3/8 inch hole in the wall behind the magnet
location, feed the switch wire through the wall and
press the switch into place.
February 7, 2007
Page 21 of 58
Part No. 4045-905, Rev C.2
Magnet
M agnetB B
Magnet AA
Magnet
Keypad
Keypad Electronics Board
E lectronics Board
Batt.
Batt.
Main
Board
Main Electronics
Electronics Board
Figure 10 Tamper Switch Installation

Note: Unit is shown from the back with the base removed.
Page 22 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
WIRING
Figure 11 illustrates the location and description of the four pin connectors on
the main circuit board and its use. Connector P5 is not used.
Blue Not Used
Brown Wiegand LED Control
White Wiegand Data 1
Green Wiegand Data 0
Red Power +12 VDC
Black Ground
Blue Main Relay COM
Green Main Relay NO
Gray Main Relay NC
*Note: Rex Loop

requires NO switch;
Door Loop requires
NC switch. Connect
commons from both
loops to Loop
Common input P2, Pin
6, White.
Green Aux Relay NO

Gray Aux Relay NC
Blue Aux Relay COM
Brown Rex Loop
Orange Door Loop
White Loop Common*
Red LED (Red +)

Black LED (Green +)
Antenna +
Antenna -
Figure 11 Pin Locator Diagram
February 7, 2007
Page 23 of 58
Part No. 4045-905, Rev C.2
5.1
MAIN RELAY
The main relay for the door-locking device is wired to connector
P1 on the EntryProx main circuit board.
5.2
GATE ACTUATOR
You can make the wire connections for a gate actuator by
connecting the Blue (C) wire and the Green (N/O) wire directly to
the input.
Note: DO NOT connect a power supply to the relay if you connect
a gate actuator.
5.3
AUXILIARY RELAY
The EntryProx unit has an auxiliary relay feature that allows for
customized alarm programming. Pins 1, 2, and 3 on the P2
connector can be wired for one of the following alarm outputs:
Alarm shunt
Forced or propped door

The alarm shunt operation allows you to use the auxiliary relay to
bypass a door contact that is monitored by a separate alarm
system. If the entry or exit is controlled by the EntryProx unit, an
intrusion alarm will not be generated if the door is opened using an
access card or PIN number, or by pressing the REX button.
The forced or propped door alarm allows you to use the auxiliary
relay to provide a local warning, such as an audible or visual
indicator if:
A door is opened without using an access card or PIN

number at the EntryProx unit.
A door is legitimately opened but is held open too long.

Note: The auxiliary relay audible and visual indicators and the
door open times can be programmed. Refer to Table 1
Programming Commands for more information.
Page 24 of 58
February 7, 2007
5.4
Part No. 4045-905, Rev C.2
REQUEST TO EXIT INPUT

When the EntryProx Request to Exit (REX) input receives a
momentary switch closure, it engages the main relay for the
programmed access time. It can be connected to a wall-mounted
exit button, to a push button under a reception desk, or to the relay
output of a passive infrared motion detector mounted above the
door on the secure side. The Request to Exit input activates the
alarm shunt to prevent false alarms when personnel use the
controlled door to exit the secured area. The Transaction Log
records all Request to Exit usages for monitoring purposes.
Locate connector P2 on the main circuit board and remove the 2pin jumper installed on pins 5 and 6.
Note: If you do not use a door contact, you need to twist the white
and orange wires together or the REX input will not function
properly.
Note: The door contact must be closed for the Request to Exit
feature to work properly
PROGRAMMING
IMPORTANT READ BEFORE PROGRAMMING
THE ENTRYPROX UNIT
KEEP A USER LIST when programming cards and PIN codes
into your EntryProx. Write down the User Location, Card Number,
PIN Code and the Name of the User. Use the blank form at the
end of this book as a photocopy master. You will need this
information if you need to delete a card or PIN at a later time.
NEW FEATURE on Rev C Model USER LOCATION 0
RESERVED FOR MASTER CODE This feature was added to
reduce service calls due to overwritten Master Codes. The Master
Code places the unit into programming mode. The master code
defaults to User Location 1, but after a Master Code is
programmed into Location 0, User Location 1 can be
reprogrammed as any User Type.
NEW FEATURE on Rev C Model - FORCED CHANGE TO
MASTER CODE This feature was added to increase security.
T
February 7, 2007
Page 25 of 58
Part No. 4045-905, Rev C.2
The Master Code must be changed from the factory default,

before any programming can be done. Write the new code down
and keep it in a safe place.
IF YOU LOSE OR FORGET THE MASTER CODE
End Users: Contact your dealer a service call is required.
Dealers: Call HID for the procedure and remember to bring the
proper hex key or security tool to the customer site!
6.1
PROGRAMMING COMMAND SEQUENCES

Command sequences are simply a series of keypad entries to add
cards and PINs or change operating characteristics of the
EntryProx unit. There are three basic steps to programming
EntryProx, using the Keypad on the control unit:
1. Place the unit in programming mode

Press 99 # Master Code *
2. Enter a Command Sequence

Press a 2-digit command number to enter cards/PINs
or specify parameters by pressing keys in various
sequences
3. Exit programming mode

Press * to exit
6.2
LED INDICATION DURING PROGRAM

MODE
A slow blinking yellow LED indicates that the unit is in program
mode.
When the yellow LED stops blinking and is OFF completely, the
unit is no longer in program mode.
A steady yellow LED indicates an error condition where:
1. You are trying to enter a card or PIN which is already

stored in another User Location
Page 26 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
2. You have pressed the wrong key in a command

sequence
Press * to clear the error condition, then enter a new
code or PIN, or re-enter the command sequence as
required. If the unit does not go into program mode,
contact your dealer or HID Technical Support.
6.3
CHANGING THE MASTER CODE

The EntryProx cannot be programmed before you change the
master code. This feature prevents users from leaving the default
code in the unit; thereby preventing unauthorized programming
and tampering. The steps are:
1. Enter programming mode using the default master

code in User Location 1.
Press: 99 # 1234 *
2. Enter a new master code into User Location 0. Press:
50 # 1 # 0000 # new master code * new master code *
(Code can be 1 6 digits. This PIN is mirrored into
User Location 1)
3. Enter a new code into User Location 1. See CARD/PIN
PROGRAMMING SEQUENCES, page 30.
4. Press * to exit program mode.
You can now program any user type into User Location 1, or you
can simply delete it. User Location 0 is not an access code it is
only used to enter programming mode. Although it is not
recommended, you can also program the same PIN used in User
Location 0 as an access code in another location it is the only
code not checked for duplication.
It is also possible to change the master code and leave the master
code in user location 1, however, this is not recommended,
because the master code can be accidentally overwritten.
February 7, 2007
Page 27 of 58
Part No. 4045-905, Rev C.2
6.4
BEFORE YOU START

Before programming cards, determine:
6.5
How many cards do I

have to enroll?
If you have more than 50-75, you may

want to batch enroll them. If you have
fewer, you may want to program one at
a time.
How are the cards

encoded: What is the bit
format, ID numbers and
facility code?
If you have sequentially numbered

cards with 26-bit format and the same
facility code, you can batch-enroll them
from the keypad. Otherwise you must
program them individually or batchenroll by sequentially placing the cards
in front of the reader. Note that if you
choose to add new 26-bit cards
manually (via the keypad), the facility
code must be entered into the unit first.
For the programming sequence used to
enter the 3-digit facility code, see Table
1 Programming Commands, item 32.
PIN CODE/CARD PROGRAMMING

BASICS
PIN codes and card numbers can be programmed manually via
the keypad. Cards can also be programmed by presentation to
the reader at the correct point in the command sequence.
When adding or modifying PIN codes or cards, the user enters a
2-digit Command, then specifies three or four data values: a user
type, a location, and a keypad-PIN and/or card.
6.6
USER LOCATIONS
These are the locations in the units memory where Card and/or
PIN User data is stored. EntryProx User Locations are numbered
1 2000. User Location 0 is reserved for the Master Code, used
for programming Cards or PINs for normal access cannot be
entered into User Location 0.
Page 28 of 58
February 7, 2007
6.7
Part No. 4045-905, Rev C.2
USER TYPES
User Types determine what happens when a user presents their
card/PIN to the reader. A User Location can be programmed as
one of four specific user types:
Toggle latch strike (0) For this user-type, when the Card is
presented (or PIN is entered) the door opens for an indefinite
period, until the card / code is reentered or another toggle code is
entered (this is useful for deliveries, for example).
Normal access (1) This is the default user type, when the Card is
presented (or PIN is entered) the door opens for the duration of
the Main Relay time.
Download Log (2) For this user-type, when the Card is presented
(or PIN is entered) the door remains locked and the Transaction
Log is Downloaded to an optional Palm PDA via the IR LED.
(There are three LEDs on the top of the unit - the IR LED is the
one on the right.) This code cannot be used to gain access
through the door.
Note The log is only downloaded and displayed, not erased.
Lockout (3) For this user-type, the keypad freezes, disallowing
all other codes, plus the door remains in the current state. During
a lockout state, card access does not continue to work. If it is
locked, it remains locked. If it is unlocked, it remains unlocked until
another Lockout code is entered, releasing it from Lockout mode.
Note: Reserve this user-type for a supervisor or override function.
6.8
PIN CODES, CARDS AND

COMBINATIONS
A User Location can be programmed with one of the four PIN
code/card combinations listed below using the programming
Commands in parentheses
(1) PIN Code ONLY (Command 50)

(2) PIN Code AND Card (Command 50 plus present card to
proximity reader)
(3) Card ONLY (Command 50 or Command 51)
(4) PIN Code OR Card (Command 52)
February 7, 2007
Page 29 of 58
Part No. 4045-905, Rev C.2
No User Location can have the same card and/or access PIN
code as another User Location.
6.9
ENTERING USER PIN CODES

EntryProx user PIN codes consist of a minimum of one digit and a
maximum of six digits. Note that a leading 0 is considered a digit,
and that the 5-digit code 12345 is different from the six-digit code
012345. Attempting to enter a user PIN code into memory that is
already stored in a different user location causes the yellow LED
to stop blinking and remain steadily lit. If this occurs, try entering a
different user code. Repeating digits in the same code is
acceptable (ex: 121122).
CARD/PIN PROGRAMMING
SEQUENCES
Following are the most commonly used command sequences for
programming user data into the EntryProx.
7.1
PROGRAMMING PIN + CARD

To program a user for both Code AND Card:
1. Place the EntryProx unit in program mode.

Press: 99 # Master Code *
2. On the EntryProx keypad
Press: 50 # user-type # user location # keypad PIN
* keypad PIN * <present card>
Here is an example, assuming a master code of 2468 and
programming user 2 with PIN 1111
Press 99#2468*
Press 50#1#2#1111*1111*
<present card>
Press *
Page 30 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
Remember to write an entry in your user list:

User:2 Type:1 PIN:1111 Card:0056 Name: John Doe
7.2
QUICK PROGRAMMING EITHER PINS OR

CARDS
A quick program feature allows user data entry with minimal
keystrokes. No command number is required. This feature
programs either a card or a PIN, not a combination, and it
automatically selects a Normal user access type. Just enter the
users location and the PIN (or present card):

2. On the EntryProx keypad, for Code Quick Enroll
Press: user location # PIN * PIN * OR for Card Quick
Enroll press: user location # ** <present card>
USER TYPES - REMINDER
0-Toggle
7.3
1-Normal
2-Download
3-Lockout
PROGRAMMING PIN CODE ONLY USE

To program PIN Code ONLY operation with Command 50, use the
following program sequence:

* keypad PIN *
February 7, 2007
Page 31 of 58
Part No. 4045-905, Rev C.2
7.4
PROGRAMMING CARD ONLY USE

To program Card ONLY use with Command 50, simply omit the
keypad PIN values from the sequence:

Press: 50 # user-type # user location # **
<present card>
7.5
PROGRAMMING CODE OR CARD

To program a user for either Code OR Card:

* keypad PIN * <present card>
3. Press * to exit program mode
7.6
BATCH LOAD CARDS BY KEYPAD ENTRY

Command 56 allows you to batch load multiple, sequential 26-bit
HID cards into the EntryProx unit. Up to 2000 users can be added
at one time. Cards need not be presented to the reader.
Requirements are:
Page 32 of 58
Cards must all have the same facility code.

Cards must be sequentially numbered
The facility code must be programmed into the unit before
any batch loading. See Table 1 Programming Commands,
Command 32 for the procedure. (This facility code cannot
be changed at a later time).
February 7, 2007
Part No. 4045-905, Rev C.2
Cards with multiple facility codes or many numbering gaps must

be entered by presentation to the reader, using Command 53.
If the Batch Loading conditions can be met:

Press: 56 # (total number of cards to be added) #
(starting user location) # card number *
repeat card number *
7.7
BATCH LOAD BY PRESENTATION

Use Command 53 to program a batch of cards into consecutive
User Locations by specifying the starting User Location, then
presenting cards or tags to the reader. Use any card format up to
37 bits. All cards are programmed alike and users are card only.
Card enrollment stops once the current user location exceeds
2000, or if you press any key to abort. Keep a written record as
you program cards.
Existing data in the User Locations being programmed is
overwritten, unless you present a card that is already programmed
into the EntryProx, in which case an error is generated. To clear
the error, press the * key; then continue presenting cards.
To batch load by presentation, follow this procedure:

USER TYPES - REMINDER
0-Toggle
1-Normal
2-Download
February 7, 2007
3-Lockout
Page 33 of 58
Part No. 4045-905, Rev C.2

Press: 53 # user type # start location # ** <present
card> <present card>
<present card>
7.8
DELETING USERS
To delete a user from the EntryProx, you must know the User
Location in which the information is stored.

2. On the EntryProx keypad,
Press: user location #**
7.9
BLOCK DELETE USERS

Use Command 58 to delete all cards / PINs in a block of User
Locations. The yellow LED will blink rapidly during the deletion
process. It can take several seconds to delete large blocks of
users. (Entering a starting user location or number of locations
which exceeds 2000 will generate a programming error.)
To block delete user locations, follow these steps:

2. On the EntryProx keypad.
Press: 8 # start location # start location # number of
locations * number of locations*
Page 34 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
CHANGING OPERATING
PARAMETERS
Many users will use the EntryProx with the factory default
operating parameters. The following commands include some of
the most commonly customized parameters. For further
refinements on EntryProx operation, review the options shown in
Table 1 Programming Commands.
8.1
CHANGING THE MAIN RELAY TIME

The main relay time applies to all users 1-2000. The factory
default main relay time is five (5) seconds. Main relay time can be
set from one to ninety-nine seconds in one-second increments
using Command 11.

2. Enter the new main relay time, in seconds (from 1 to
99). For example, to enter 10 seconds
Press: 11 # 10 # 0 # **
8.2
INVALID PIN LOCKOUT

Command 30, Option 18 allows you to enable or disable the
Invalid PIN Lockout (IPL) feature. This feature prevents
unauthorized persons from gaining entry by guessing PIN codes
or Master Codes. When a preset number of invalid entries is
exceeded (set by using Command 32 option 4, default is 5) the
EntryProx will either trigger the Forced Door output, or the keypad
will be disabled for a user-configurable time period (select the
action, using Command 30, option 19, and then set lockout time
by using Command 32 5).
The invalid PIN code count is reset to zero by any of the following:
Entering a valid keypad PIN

Presenting a programmed Prox card
February 7, 2007
Page 35 of 58
Part No. 4045-905, Rev C.2
Entering a valid [99 # Master code*] sequence
The expiration of the keypad timer

The Invalid PIN Lockout function disables all keypad PIN entries
with the exception of the [99 # Master Code*] sequence for the
duration of the lockout.
To clear an active timed Invalid PIN Lockout do any of the
following:
Disconnect power to the system

Present a valid prox card programmed as Card Only or
Card OR Code
Enter the [99 # Master Code *] sequence

Note that if an invalid [99# Master Code*] is entered as part of the
sequence to clear the IPL, a subsequent good [99# Master Code*]
sequence will not cancel the current lockout.
8.3
RESETTING THE MASTER CODE AND

SYSTEM DEFAULTS ONLY
Command 40 erases everything from the EntryProx memory
except the user list and transaction log and restores the default
settings. This is useful if the EntryProx unit has experienced
programming problems, or if you wish to delete earlier
programming.
When you do this command the following rules apply:
Page 36 of 58
If user #0 has not been programmed and user #1 is

programmed then user #0 is erased and user #1 is set to
default (1234).
If user #0 has been programmed and user #1 has not been
modified, user #0 and user #1 are set to default data (1234).
If user #0 has been programmed and user #1 has been
modified, user #0 is set to default (1234) and user #1 is not
changed.
February 7, 2007
Part No. 4045-905, Rev C.2
Note: You must change the master code after performing this
command.

2. Press: 40 # 00000 # 00000 # **
8.4
ERASING ENTIRE MEMORY / RESETTING

SYSTEM DEFAULTS
Command 46 deletes everything from the EntryProx memory
including the user list but not the transaction log and restores the
default settings. This is used as a last resort if you need to erase a
specific user and could not retrieve the Programmed User List.
After performing this command the master code must be
reprogrammed.
Place the EntryProx unit in program mode.

2. Press: 46 # 00000 # 00000 # **

8.5
TURNING KEYPRESS AUDIBLE

FEEDBACK ON/OFF
The Keypress Audible Feedback command enables the sounder
to beep once for each key press. This feature provides an audible
acknowledgment that a particular key was pressed hard enough
for the unit to understand. The factory-shipped default setting is
ON, but it can be toggled ON and OFF as desired using command
30.

2. To enable this feature
Press: 30 # 0 # 1 # **
February 7, 2007
Page 37 of 58
Part No. 4045-905, Rev C.2
3. To disable this feature

Press: 30 # 0 # 0 # **
8.6
TURNING KEYPRESS VISUAL FEEDBACK

ON/OFF
The keypress visual feedback feature lights the LED once for each
key press. This feature provides a visual acknowledgment that a
particular key was pressed hard enough for the unit to understand.
The factory-shipped default setting is ON, but it can be toggled ON
and OFF as desired.

2. To enable this feature
Press: 30 # 1 # 1 # **
3. To disable this feature
Press: 30 # 1 # 0 # **
8.7
AUTO ENTRY ENABLE

This function is not recommended for use, as it lowers the overall
security of the unit and affects programming sequences ending
with the * key. It is set with the 30# command (Set/Clear Standard
Options). When this feature is enabled, any PIN code the same
length as the master code does not require the * key. Leave this
feature in the default mode, which is OFF.
Page 38 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
DOWNLOADING DATA TO A PDA

The EntryProx unit can download a Transaction Log and a
Programmed User List to an optional Palm Personal Digital
Assistant (PDA) via the IR LED. There are three LEDs on the top
of the EntryProx unit - the IR LED is the one on the right.
9.1
USING THE DCD PROGRAM

The Data Collection Device (DCD) Application is provided as a
free download on the HID Website
(http://www.hidcorp.com/downloads/entryproxdcd ). The DCD
application is downloaded to a PC, and is then downloaded to the
Palm via the cradle or IR interface. Download instructions and a
list of compatible Palm models are shown on the website. Refer to
the Palm user documentation for instructions on how to operate
the Palm PDA, how to install programs, and for the location of the
Palm IR Receiver.
1. Touch the Data Collection icon on the PDA screen.

2. The program will start, displaying three menu options:
Retrieve, Files, and Settings
3. Click on Settings to be sure the following parameters

are selected:
Comm Method Ir Channel 2

Comm Speed 19200
February 7, 2007
Page 39 of 58
Part No. 4045-905, Rev C.2
Protocol Printer
Timeout (Seconds) 30
4. To download data from the EntryProx Unit to the Palm:
Touch Retrieve on the PDA screen

Place the Palm IR receiver within 1/2 of the
EntryProx IR LED (to the right of the yellow LED)
Enter the required command sequence at the

EntryProx keypad
You have 30 seconds to enter the command sequence
after entering the receive screen. If the data begins to
send before you press Retrieve, then you will miss the
beginning of the data.
5. Command sequences are described in detail in the

following sections.
Page 40 of 58
February 7, 2007
9.2
Part No. 4045-905, Rev C.2
SELECTING TRANSACTION LOG

INFORMATION
You can selectively program specific transaction events to be
included (or not) on the Transaction Log. By masking out certain
events, you direct the unit not to save those events in memory and
thus they do not appear in the log. The factory default is for all
transaction events to be saved in memory and included in the log.
The procedure follows:

2. To turn OFF an event (keep it from being
stored/logged)
Enter: 73 # Event Code # 0 # **
3. To turn an event ON
Enter: 73 # Event Code # 1 # **
The Event Code is a two-digit number that represents a specific
transaction as listed in the following table.
February 7, 2007
Page 41 of 58
Part No. 4045-905, Rev C.2
The following transaction events can be set/cleared (saved/not

saved) and therefore downloaded/not downloaded.
EVENT CODE
TRANSACTION EVENT
01
Access Denied
02
Program Denied
04
REX (Request to Exit)
05
Door Ajar
06
Door Closed
07
Forced Door
10
Error Lockout Activated
12
Facility Code Access
16
Download (to PDA)
17
Access
20
TGL ON (Toggle ON)
21
TGL OFF (Toggle OFF)
24
Lo ON (Lockout ON)
25
Lo OFF (Lockout OFF)
27
MSMTCH (Mismatch on Card and Code entry)
29
Program mode started
30
Log erased
Page 42 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
10 DOWNLOADING A
TRANSACTION LOG
Using the optional Palm PDA with the DCD Program, you can
download and display a Transaction Log via the EntryProx IR port.
Transaction Logs can be downloaded using two different methods,
(1) by programming a card or code to Download the transaction
log to the PDA and (2) by placing the EntryProx unit into program
mode and manually entering the Display Transaction Log
command.
10.1 INITIATE A TRANSACTION REPORT

DOWNLOAD
2. For a CODE DOWNLOAD
Press: 50 # 2 # user location # code * code *
3. For a CARD DOWNLOAD
Press: 50 # 2 # user location # ** <present card> and
then present the card at the proximity reader.
Note: Entering the programmed PIN code or presenting the card
subsequently causes the unit to download a Transaction Log to
the optional PDA.
10.2 MANUALLY DOWNLOADING A

TRANSACTION LOG
2. Touch Retrieve on the PDA screen
February 7, 2007
Page 43 of 58
Part No. 4045-905, Rev C.2
3. Place the Palm IR receiver within 1/2 of the EntryProx

IR LED (to the right of the yellow LED)
4. On the EntryProx, press 70 # 0 # 0 # **
The PDA will display a progress bar while collecting the
data, and when done will display End of Dump
(download). You can touch Close/Stop on the PDA or
wait for the unit to time out.
When prompted for a Session Name, you can place
your stylus on the line containing the date information
and add to it or replace it with descriptive text.

The 70 command is logged in the transaction buffer (in
memory), providing a reference as to when the log was
downloaded. Figure 12 shows a sample Transaction
Log.
Figure 12 Transaction Log

Page 44 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
The Palm PDA will store reports after they are

downloaded.
To view a stored report, touch Files, select a report
from the list and click Action. The drop-down menu
selections are Info, View and Remove.
Info gives the time and date the report was

recorded.
View displays the report.
Top line Current Line/Total Lines
Remove allows you to delete the report.

The top line of the screen shows the current line and
total number of lines as you scroll or page up and down
through the report.
Here is a description of the report layout:
Second line Session Data
Transaction lines Time, Date, User Location,
Action
Time: 24-hour format
Date: mm/dd/yyyy
User Location: 0-2000
Action: Describes each event
10.3 ERASING A TRANSACTION LOG

The Transaction Log should be erased from memory in the
EntryProx after being downloaded to prevent conflicting logs. To
erase the log, enter the following sequence:

2. To erase the transaction log
Press: 76 # 00000 # 00000 # **
February 7, 2007
Page 45 of 58
Part No. 4045-905, Rev C.2
10.4 DOWNLOADING A PROGRAMMED USERS

LIST
The Programmed Users List can be downloaded to the optional
Palm PDA via the units IR LED. The list identifies the user
location for each users data. It also displays user locations that
are not programmed, so to avoid an unnecessarily long file, the
download can be stopped when a sufficient percentage of records
have been processed. The percentage of records downloaded is
continually updated during the download process.

2. Touch Retrieve on the PDA
3. Hold the optional PDA up to the EntryProx IR port
steadily (about inch away; the IR port is located to
the right of the yellow LED)
4. Then, on the EntryProx, press 25 # 0 # 0 # **
The PDA will display a progress bar while collecting the
data (Retrieving users %) and when done will display
End of Dump (download). You can touch Close/Stop
on the PDA or wait for the unit to time out. When
prompted for a Session Name, you can place your
stylus on the line containing the date information and
add to it or replace it with descriptive text.
Page 46 of 58
February 7, 2007
Part No. 4045-905, Rev C.2
5. When the list is complete, press * to exit program

mode.
Here is a description of the Report Layout:
Top line Title

Second line Session Data
Column 1 User location
Column 2 user type (see table)
Column 3 pin code
Column 4 site code/card number
11 WIEGAND MODE
If you program the EntryProx unit to operate in Wiegand mode
with a separate access control panel, the following features are
not accessible:
The EntryProx unit does not control door lock or unlocking

operations.
The EntryProx unit is not able to store codes in memory.
The main and auxiliary relay functions are turned off.
The door monitor and Request to Exit inputs are disabled.

For more information on programming the EntryProx unit for
Wiegand operation, please contact your local distributor.
February 7, 2007
Page 47 of 58
Part No. 4045-905, Rev C.2
11.1 PIN CODE OUTPUT IN WIEGAND MODE

The system transmits keypad PINs while operating in Wiegand
mode by processing any digit sequence terminated with the [*] key
as 26-bit Wiegand data. The current facility code (set using Code
32 - 2) will be used. Entering any PIN over 65535 will cause an
error condition and no data will be sent.
Because keypad data is sent in a card data format, it may not be
possible for some panels to perform CARD AND CODE operation
(requiring both) to gain access. If your panel cannot accept and
interpret 26-bit format as PIN data, be sure to configure the user at
the PC host software by entering the code into the CARD data
field for that user, not the keypad PIN number field.
11.2 LED Control Options for Wiegand Mode

The combined programming for Options 30#9 30#12 and the
Wiegand LED Control line affect the LED display in Wiegand
mode. The following table shows how the LED will behave when
the LED control line is open (normal) or grounded (asserted by the
access control panel).
G = Green, R = Red, Y = Yellow. See the following section for
more on option programming.
Opt 9
Opt 10
Opt 11
Opt 12
Page 48 of 58
Led Ctl Open

Led Ctl Gnd
February 7, 2007
Part No. 4045-905, Rev C.2
12 PROGRAMMING COMMANDS
Read the following table before completing programming of your
EntryProx unit; it describes various programming commands and
how to execute them. As with the previously described
commands, you must first press 99 # (Master Code) * to enter
programming mode, enter the desired command sequence, and
then press * to exit programming mode. Ref number is for
reference only, not to provide an ordered sequence of commands.
Table 1 Programming Commands

Ref
IF YOU WANT
TO
PRESS
DETAILS
Enter program
mode
99 # (Master
Code) *
yellow LED blinks slowly
Program new
master code into
user location 0
50 # 1 # 0000 #
master code *
master code *
example: 4321 master code
Set main relay

time
11 # tt # 0 # **
tt = 1 - 99 seconds
Set AUX relay

output
15 # output
mode
Output Modes:
# 0 # **
1 = shunt,
(50 # 1 # 0000 # 4321 * 4321

*)
0 = disabled,
2 = forced door,
3 = propped door
Delete users
User Location #
**
Example:
To delete user 100, press:
100#**
Download a
transaction Log
70 # 0 # 0 # **
Hold optional Palm PDA

IR receiver near the
EntryProx IR LED.
February 7, 2007
Page 49 of 58
Part No. 4045-905, Rev C.2
Ref
7
IF YOU WANT
TO
PRESS
DETAILS
Set/clear standard
30 # option # s/c
See the following Option
option
# **
numbers and descriptions.
If Option 30# 14# is enabled, this sets the time that a card must be
removed from the RF field before it can be re-read. If option 30#14# is
disabled, this sets the time between successive readouts, used in either
standalone or Wiegand mode.
Option Number/Description
Set/Clear
0: Audio keypress feature
0 = OFF/1 = ON
1: Visual keypress feature
0 = OFF/1 = ON
2: Auto entry enable
0 = OFF/1 = ON
(Recommend OFF)
3: Stand-alone/Wiegand operation
4: Facility code access (26-bit cards only).
Note: this disables the toggle card function.
0 = standalone/1=Wiegand
0 = OFF/1 = ON
5: Forced door audio alert

6: Propped door audio alert
0 = OFF/ 1 = ON
7: Internal Request to Exit switch
0 = OFF/1 = ON
8: US/EU Daylight Savings rollover dates
0 = OFF/1 = ON
9: Wiegand red LED enable
0 = US/1 = European
10: Wiegand red LED active state

11: Wiegand green LED enable
0 = OFF/1 = ON
12: Wiegand green LED active
0 = LOW/1 = HIGH
13: Automatic Daylight Savings Time change
0 = OFF/ 1 = ON
14: Prox card antipassback select
0 = LOW/1 = HIGH
0 = OFF/ 1 = ON
18: Invalid PIN lockout select

19: Invalid PIN lockout action
0 = OFF / 1= ON (prevents
multiple card reads in
Wiegand mode)
0 = OFF / 1= ON
0 = TIMED LOCKOUT / 1 =
Forced Door Output
Page 50 of 58
Download
programmed user
list
25 # 0 # 0# **
Hold optional Palm PDA IR

receiver near the EntryProx
IR LED.
February 7, 2007
Part No. 4045-905, Rev C.2
Ref
IF YOU WANT
TO
PRESS
DETAILS
Download
programmed user
list (starting at a
certain user)
25 # 0 # start
user # **

IR LED.
10
Change Wiegand
& Miscellaneous
parameters
32 # parameter
# value # **
Parameter/Value
0, Wiegand pulse width,
default=8, 160s, (1=20s),
range= 1- 255
1, Wiegand interpulse
spacing, default=32, 640s,
(1=20s), range=1-255
2, facility code/0-225
(default = 1) (26-bit cards
only) verify!
3, Process card timer 2 240
in second increments,
defaults to 4 1 second
4, Invalid PIN lockout
threshold 1 50 attempts
(defaults to 5)
5, Invalid PIN lockout
duration 1 255 in 5 second
increments (defaults to 60 5 minutes)
11
12
Set system time

Set system date
41 # hhmm # 0
# **
hhmm = hour/minute,
42 # mmddyy #
dow # **
mmddyy =
24-hr format
month, day, year;
dow = day of week,
1 = Sunday
13
Set door number
43 # nnnn # 0 #
**
nnnn = door number (for

downloaded reports)
February 7, 2007
Page 51 of 58
Part No. 4045-905, Rev C.2
Ref
IF YOU WANT
TO
PRESS
DETAILS
14
Set propped door
44 # ttt # 0 # **
ttt = propped door time, to

nearest 10's seconds,
entered
time (this sets

delay time for
both the Aux
Relay and local
sounder)
15
Set forced door
as 10 -990; default = 30
seconds
45 # ttt # 0 # **
time (this sets

active time for
both the Aux
Relay and local
ttt = forced door time, to

nearest 10's seconds,
entered
as 10 - 990; default = 10
seconds
sounder)
16
Delete memory
40 # 00000 #
except user list
00000 # **
and restore
system defaults
(also see
command 46)
17
18
Delete all memory

and reset system
defaults
46 # 00000 #
Program user:
50 # user-type #
user location #
code * repeat
code *
Code ONLY
NOTE: You can
program the four
types of users
shown to the right
19
Program user:
Code AND Card
00000 # **
User Types:
0 - Toggle/latch strike
1 - Normal Access
2 - Log Download
3 - Lockout
50 # user-type #
user location #
code * repeat
code *
<present card>
20
Program user:
Card ONLY
50 # user-type #
user location # *
*
<present card>
Page 52 of 58
February 7, 2007
Ref
IF YOU WANT
TO
PRESS
20A
Program new
master code into
user location 0
50 # 1 # 0000 #
master code *
master code *
21
Program card
user manually:
Card ONLY (26bit cards ONLY)
51 # user-type #
user location #
card ID * card ID
*
Program user:
52 # user-type #
user location #
code* repeat
code *
22
Code OR Card
Part No. 4045-905, Rev C.2
DETAILS
the card ID appears on the

card (facility code must be
entered first; see 32 # 2 #
command)
<present card>
23
Program a group
of consecutive
users by
presenting cards
53 # user type #
start location #
**
<present card>
<present card>
<present card>
24
Perform batch
entry of users:
Card ONLY (26bit cards ONLY)
56 # total count
# starting user
location #
starting card ID
* starting
Programs card-only users.

Stops at user location 2000,
or press any key to abort.
Erases existing
programming. If an existing
card is presented, an error
will occur press * to resume
the card ID appears on the
card; (facility code must be
entered first; see 32 # 2 #
command)
card ID *
25
Block Delete
Users
58 # start user #
start user #
number of users
* number of
users *
26
Quick Enroll Card
User Location #
* * <present
card>
Yellow LED blinks rapidly;

allow several seconds for
large blocks of users.
Cannot delete: master user,
more than 2000 users, or
user location greater than
2000.
February 7, 2007
Page 53 of 58
Part No. 4045-905, Rev C.2
Ref
IF YOU WANT
TO
PRESS
DETAILS
27
Download
Transaction Log
via IR port
70 # 0 # 0 # **

IR LED.
28
Set transaction
log mask
(set/clear event
logging)
73 # event # set/
clear # **
Prevent specified
transactions from being
logged.
Set =0 (prevent)
Clear = 1(restore)
See the following Code Transaction Event list.
Code Transaction Event

01 Access Denied
02 Program Denied
04 Request to Exit
05 Door Ajar
06 Door Closed
07 Forced Door
10 Invalid PIN Lockout
12 Facility Code Access
16 Download to PDA
17 Access
20 Toggle ON
21 Toggle OFF
24 Lockout ON
25 Lockout OFF
27 Mismatch
29 Program Mode started
30 Log erased
29
30
Page 54 of 58
Reset transaction
76 # 00000 #
Log
00000 # **
To exit Program
* (after final
mode
command)
yellow LED stops flashing
February 7, 2007
Part No. 4045-905, Rev C.2
13 LED/SOUNDER STATUS
INDICATIONS
Table 2 LED/Sounder Indications
LED OR
SOUNDER
VISUAL/AUDIBLE
CONDITION
DESCRIPTION
Yellow LED
Slow blink
Unit is in Program mode
Rapid blink
Verify mode is active

(checking that the last
two values in sequence
match)
Bi-Color LED
Steady
Program error; to clear,

press *
Very rapid blink
Memory (EEPROM)
erase is in progress
commands 40/46, 58
loop-back)
Steady red
Strike is locked
Steady green
Strike is energized
(timed or latched)
Slow blinking green
Transferring data to
PDA
Solid green with red

flicker
Strike toggle is unlocked

and used lockout active
Red/green alternating
Awaiting second form of

ID during Card AND
Code access attempt
February 7, 2007
Page 55 of 58
Part No. 4045-905, Rev C.2
LED OR
SOUNDER
Sounder
Page 56 of 58
VISUAL/AUDIBLE
CONDITION
DESCRIPTION
Red blink
User lockout is active

and strike locked; red
LED drops out for 100
ms every second;
normal users cannot
change the state of the
relay. This also
indicates Invalid Pin
Lockout.
Short beep (100 ms)

every 2 seconds
Propped door is active
Sounder 1/2 second on,

1/2 second off
Forced door is active
3 rapid beeps after code

is entered or card is
presented
Code or Card is not

found
3 slow beeps (250 ms),

then a single beep
Self-test is complete
1 single beep
Valid card access
February 7, 2007
Part No. 4045-905, Rev C.2
Instructions: Do not write on this page - use it as a photocopy

master. Copy the chart at a 200% enlargement. Make as many
copies as required to record all programmed users, and write
information in the appropriate spaces. Place the users charts in a
binder, and keep them in a secure location.
February 7, 2007
Page 57 of 58
HID Global (California, USA)

support: [email protected]
main: (949) 598-1600
support: 1-800-237-7769
fax number: (949) 598-1690
HID Corporation, Ltd. (Haverhill, UK)

main: +44 (0) 1440 714 850
support: +44 (0) 1440 711 822
fax number: +44 (0) 1440 714 840
HID Asia Pacific Ltd. (Hong Kong)

main: (852) 3160 9800
support: (852) 3160 9802
fax number: (852) 3160 4809
www.hidcorp.com
An ASSA ABLOY Group company

Card Reader Manual

Uploaded by

Copyright:

Available Formats

Card Reader Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Card Reader Manual

Uploaded by

Copyright:

Available Formats

9292 Jeronimo Road

Part No. 4045-905, Rev C.2

EntryProx User Guide

PRODUCT OVERVIEW .................................................... 4

CARD/PIN PROGRAMMING SEQUENCES .................. 30

CHANGING OPERATING PARAMETERS .................... 35

DOWNLOADING DATA TO A PDA ............................... 39

DOWNLOADING A TRANSACTION LOG ..................... 43

WIEGAND MODE ........................................................... 47

PROGRAMMING COMMANDS ..................................... 49

LED/SOUNDER STATUS INDICATIONS ...................... 55

EntryProx User Guide

Part No. 4045-905, Rev C.2

Figure 5 Removing the P4 Connector ........................................... 15

Reformatted, added correct IP statement

Error correction in EntryProx User Guide

Added PDA support for logging data.

Part No. 4045-905, Rev C.2

EntryProx User Guide

KEEP A USER LIST when programming cards and PIN

CONSIDER A SECURE INSTALLATION if installing on an

EntryProx User Guide

Part No. 4045-905, Rev C.2

The EntryProx unit is compatible with all HID proximity access

PRE-PROGRAMMING THE UNIT BEFORE

Part No. 4045-905, Rev C.2

EntryProx User Guide

5% to 95% relative humidity,

10 - 15V DC, linear, filtered and regulated power

5.25 in (13.3 cm)

1.625 in (4.1 cm)

Form C (switches up to 1A inductive load, 2A

4000 Hz, defeatable

EntryProx User Guide

Part No. 4045-905, Rev C.2

Master Code (User Location 1)

Code must be changed before programming the

Audible Keypress Feedback

Local Propped Door Sounder activates after

Local Forced Door Sounder activates

Data Output Port

Infrared (IR) port

Part No. 4045-905, Rev C.2

EntryProx User Guide

I. Silicone Rubber Cushion

M. Lithium Coin Cell Battery (see page

N. Cover screws hex and tamper.*

H. Press to Exit Label

* - not shown in Figure 1

EntryProx User Guide

Part No. 4045-905, Rev C.2

Figure 1 Factory Supplied Parts

INSTALLER SUPPLIED PARTS LIST

Appropriate DC power supply (10-15VDC, linear type)

Part No. 4045-905, Rev C.2

EntryProx User Guide

CAUTION Replace Battery with Panasonic BR1225 only.

If your installation must comply with the UL 294 Standard

PRECAUTIONS FOR OUTDOOR

1. Use silicone to seal wire runs and mounting holes