Vol03 Tab02

SPD, Power Conditioning, PF Capacitors
and Harmonic Filters

Industrial Surge Protection Products
2.1
Surge Protection and Power Conditioning

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPD Series for Integration into Electrical Distribution Equipment. . . .
SPD Series for Mounting External to Electrical Distribution Equipment
SPD MAX Series Surge Protection . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPC Surge Protective Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SP1 Surge Protective Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SP2 Surge Protective Device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AEGIS Powerline Filters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sag Ride-Through (SRT2). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Voltage Regulator (EVR) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
2
2
2
2
2
2
2
Power Factor Correction and Harmonic Filtering

Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOVAR 300 Automatic Power Factor Correction Capacitor Systems
AUTOVAR 600 Automatic Power Factor Correction
Capacitor Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOVAR FilterLV Automatic Detuned Filter . . . . . . . . . . . . . . . . . .
Transient-Free Static Switching Power Factor Correction Units . . . . .
HCU2 Harmonic Correction Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-49
V3-T2-51
V3-T2-54
V3-T2-63
V3-T2-67
V3-T2-74
V3-T2-81
V3-T2-83
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Volume 3Power Distribution and Control Assemblies CA08100004EAugust 2016 www.eaton.com
V3-T2-1
2.1
2
SPD, Power Conditioning, PF Capacitors and Harmonic Filters

Contents
Industrial and Commercial Surge Protection
Description
Page
Introduction
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . .
SPD Series for Integration into Electrical
Distribution Equipment . . . . . . . . . . . . . . . . . . . . .
SPD Series for Mounting External to
Electrical Distribution Equipment . . . . . . . . . . . . .
SPD MAX Series Surge Protection . . . . . . . . . . . . .
SPC Surge Protective Device . . . . . . . . . . . . . . . . .
CVX050/100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SP1 Surge Protective Device. . . . . . . . . . . . . . . . . .
AEGIS Powerline Filters. . . . . . . . . . . . . . . . . . . . . .
Sag Ride-Through (SRT2). . . . . . . . . . . . . . . . . . . . .
Electronic Voltage Regulator (EVR) . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
2
2
2
2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
Introduction
Industrial and Commercial Surge Protection
2
2
2
2
2
2
SPD Series for Integration

into Electrical Distribution
Equipment
SPD Series for Mounting
External to Electrical
Distribution Equipment
SPD Series Sidemount Units

Specification grade surge
protective devices for
installation external to
electrical distribution
equipment.
Critical Load Protection

Series filtering and surge
protection for critical singlephase loads.
SPD Series Integrated Units

Specification grade surge
protective devices installed
within Eatons electrical
assemblies.
Current ratings up to 60 A
120 and 240 Vac units
24 and 48 Vdc units
DIN mounting available on
some models
Up to 80 kA of peak surge
protection
AC units are UL 1449 4th
Edition and UL 1283 5th
Edition listed
2
2
2
SPD Series Sidemount Unit
Commercial and Light

Industrial Surge Protection
The SPC Series offers robust
protection in a compact,
flexible design and is
configurable for a wide range
of commercial and light
industrial applications.
The SPC combines surge
suppression components
and the options of EMI/RFI
filtering, Form C contacts
and an audible alarm.
Surges (also known as
transients), due to lightning,
utility grid switching,
switching of external/internal
inductive or capacitive loads,
and other sources, travel on
power line conductors
throughout the electrical
distribution system, causing
system operating problems
and equipment downtime.
2
2
2
2
SPD Series Integrated Unit
SPC Series
AEGIS Products
2
V3-T2-2

2.1
Surge Protection for Sub-Panel and OEM Applications

In todays business
environment that calls for 24
hours a day, 7 days a week
uptime and reliability, Eatons
CVX050 and CVX100 surge
protective devices (SPDs)
ensure that a customers
investment in equipment and
processes is protected from
the damaging effects of
voltage transients. Designed
for installation on service
entrance, branch panels or
individual equipment
disconnects, the CVX050/100
provides enhanced surge
protection for mission-critical
applications.
Panelboards with Integrated

Surge Protective Devices
Available in standard and

custom configurations
Ratings:
120/240 Vac, singlephase, three-wire
208Y/120 Vac, threephase, four-wire
480Y/277 Vac, threephase, four-wire
600Y/347 Vac, threephase, four-wire (other

voltage configurations
are available)
2
2
2
2
2
Surge Protective Devices can be
Integrated within a variety of Eaton
Electrical Assemblies
2
2
2
Copper bus
12, 18, 24, 30, 36 and
42 circuits
Bolt-on branch breakers
A full range of factory
installed modifications
and accessories
Fully rated or series rated
2
2
2
2
2
2
Power Conditioning
Sag Ride-Through (SRT2)
The sag ride-through (SRT2)
is a power conditioner that
corrects voltage sags to
maintain uptime and
productivity.
Electronic Voltage
Regulator (EVR)
The electronic voltage
regulator (EVR) is designed
to meet the needs of
customers who experience
voltage regulation problems
due to brownout conditions
from their electric utilities.
2
2
2
2
2
2
Electronic Voltage Regulator (EVR)
2
2
2
Facility-Wide Power Protection Solutions

A facility-wide protection
approach should be
employed to address power
quality issues. This approach
minimizes overall lifecycle
costs and optimizes facility
uptime. The following is a
recommended design
approach for implementing
facility-wide Eaton power
protection solutions.
The most accepted design methodology is based on two concepts:

1. Ensure proper grounding conditions exist.
All forms of power protection/conditioning
rely on good grounding, bonding and
earthing practices.
2. Surge protection should be installed

at key distribution panels and
critical loads.
2
2
2
2
2
V3-T2-3
2.1
2
2
2
2
2

Application Description
Application Recommendations for Surge Products

Application Type
Eatons Surge Product
Features and Competitive Advantages
Design build
SPD Series integrated units
Ideal package for any commercial facility
Chain stores
SPD Series sidemount units
Cost-effective, reliable protection using the SPD Series or SPC units
Small facilities
SPC units
Light Commercial
CVX units
SP1 units
Large Projects
SPD Series integrated units in panelboards, switchboards,

MCCs, switchgear, busway and automatic transfer switches
Able to meet competitors surge protection specifications
Commercial
Government
Wall space savings by using integrated SPD Series units
Schools
SPD MAX units
Quick-ship capabilities from Eaton assembly satellites and service centers
Institution
AEGIS units for critical load applications
Power conditioning capability for a wide variety of applications
Military
Power conditioners (EVR and SRT2 units)
Including:
Increased surge protection performance by using integrated SPD Series units
Industrial
Including:
SPD Series integrated units in panelboards, switchboards,

MCCs, switchgear, busway and automatic transfer switches
Increased surge protection performance by using integrated SPD Series units
Small and large facilities

WWTP
MCCs with SPD Series units installed protect drives from damage
SPD MAX units
AEGIS products protect expensive critical loads from harmful damage
AEGIS units for critical load applications such as PLCs,

robotics applications, etc.
EVR units correct voltage regulation problems
Power conditioners (EVR and SRT2 units)
Wall space savings by using integrated SPD Series units
SRT2 units correct voltage sag problems
OEM
Any OEM customer including:
SPD Series integrated units
Years of experience in a variety of OEM applications
Integrators
Application assistance and recommendations
Medical equipment
CVX units
Small footprint enables integration in a variety of applications
SPC units
Ability to meet customized requirements
Automation and control
2
2
2
2
2
SP1 units
SP2 units
AEGIS units for critical load applications
Telecommunications
Including:
Panelboards and automatic transfer switches with integrated SPD Series units
Ability to meet customized requirements
Cellular sites
Application assistance and recommendations
Microwave
CVX units
SPC units
PCS
SP1 units
Paging systems
SP2 units
2
2
2
2
2
2
2
2
V3-T2-4

2.1
Contents
SPD Series Sidemount Units
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Overview
SPC Surge Protective Device. . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SP1 Surge Protective Device . . . . . . . . . . . . . . . . . .
AEGIS Powerline Filters . . . . . . . . . . . . . . . . . . . . . .
Sag Ride-Through (SRT2) . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-2
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
Learn
Online
2
2
2
2
2
2
2
2
Product Description
SPD Series Integrated Units
Product Overview
Eatons SPD series surge
protective devices are the
latest and most advanced
UL 1449 4th Edition certified
surge protectors. Units are
available integrated within
Eaton electrical assemblies,
including panelboards,
switchboards, motor
control centers, switchgear,
automatic transfer switches
and bus plugs.
Features, Benefits and Functions

A complete offering of
sidemount units designed
for mounting external to
electrical distribution
equipment is also available.
Application of SPD Series
units throughout a facility
will ensure that equipment
is protected with the safest
and most reliable surge
protective devices available.
SPD Series units are available
in all common voltages and
configurations and also
in a variety of surge current
capacity ratings from 50
through 400 kA. Three
feature package options are
also available to choose from,
ensuring the proper unit is
available for a variety of
applications.
Uses thermally protected

metal oxide varistor (MOV)
technology
Three feature package
options
True protection status
indicators report the status
of the protection elements,
not the status of the
applied power
Available integrated
within the following
Eaton electrical assemblies:
panelboards, switchboards,
motor control centers,
switchgear, automatic
transfer switches and
bus plugs
10-year warranty
(15-year warranty with
online registration)
Safety Features
All units use thermally

protected metal oxide
varistor technology (MOV)
as their core surge
suppression component.
Usage of this technology
ensures safe operation
when the unit is subjected
to abnormal conditions
such as temporary
overvoltage or high fault
current conditions. Under
such conditions, the selfprotected MOVs are
removed from the circuit
quickly and safely before a
potentially unsafe condition
can occur
SPD Series units contain

no replaceable parts such
as surge modules, fuses,
or surge counter memory
backup batteries. This
prevents potential arc flash
and shock hazards, as the
units require no periodic
service or user intervention
after installation
Integrated versions of the

unit are factory installed
and sidemount versions
are factory sealed. These
important safety measures
further enhance user
safety
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-5
2.1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

Three Feature Package

Options Available
The SPD Series provides
users with the option of
selecting between three
feature packages. These
feature packages are the
basic, standard and standard
with surge counter. The
proper feature package
can be selected based on
the requirements of the
application or specification.
A side by side comparison of
the individual features found
in each package is below.
Basic Feature Package
The basic feature package is
perfect for applications where
basic, cost-effective, safe and
reliable surge protection is
required, but budgets dont
allow for extra, additional
features. Rather than
sacrifice performance or
safety due to cost, SPD
Series units with the basic
feature package provide you
with high-performing surge
protection without sacrificing
safety or reliability. The basic
feature package provides
the same level of surge
protection and safety
provided by the standard and
standard with surge counter
feature packages minus
some of the features found in
them. The package contains
dual-colored protection status
LEDs that report the true
status of the protection in
each phase/mode. All fourwire plus ground units also
contain an additional set of
dual-colored protection status
LEDs that report the status
of the protection in the
neutral/ground mode.
Standard Feature Package

The standard feature package
includes all of the features
found in the basic feature
package, plus an audible alarm
with silence button, EMI/RFI
filtering, and a form C relay
contact that can be used for
remote annunciation of the
SPDs status. The audible
alarm activates and the form
C relay contact changes state
when any loss of protection is
detected or a fault condition
exists with the unit. Should
such a condition occur, the
audible alarm can be silenced
by pressing the silence button.
The EMI/RFI filter provides up
to 50 dB of noise attenuation
over the range of 10 kHz
through 100 MHz.
Standard with Surge
Counter Feature Package
The standard with surge
counter feature package
includes all of the features
found in the standard feature
package plus a six-digit surge
counter with a reset button.
The surge counter indicates
the ongoing count of the
number of surges the unit has
been exposed to and stores
them in nonvolatile memory.
Should power to the SPD
Series unit be completely
interrupted, the surge counter
will recall and display the
surge count prior to the
interruption when power is
restored. Unlike many surge
protectors, the SPD Series
surge counter memory
feature does not require a
backup battery that would
require periodic replacement
in order to achieve its
memory functionality.
Side-By-Side Comparison of the SPD Series Available

Feature Packages
Feature Package Comparison
Basic
Standard
Standard with
Surge Counter
Surge protection using self-protected

MOV technology
Dual-colored protection status indicators

for each phase
Dual-colored protection status indicators

for the N-G protection mode
Audible alarm with silence button
Form C relay contact
EMI/RFI filtering, providing up to 50 dB of

noise attenuation from 10 kHz to 100 MHz
Standards and Certifications
Integrated versions of
the unit are UL 1449
4th Edition recognized
components for the
United States and Canada,
covered by Underwriters
Laboratories certification
and follow-up service
Sidemount versions are
UL 1449 4th Edition listed
devices and are also
CSA approved
2
2
2
2
2
2
2
2
V3-T2-6
Surge counter with reset button
Technical Data
and Specifications
20 kA nominal discharge
current (In) rating
(maximum rating
assigned by UL)
50 through 400 kA surge
current capacity ratings
200 kA short-circuit current
rating (SCCR)

SPD Series Unit Integrated within an Eaton Panelboard
2.1
Contents
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Distribution Equipment
Standards and Certifications . . . . . . . . . . . . . . . .
Catalog Number Selection . . . . . . . . . . . . . . . . .
Technical Data and Specifications . . . . . . . . . . . .
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-2
V3-T2-5
V3-T2-8
V3-T2-8
V3-T2-9
V3-T2-10
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
2
2
2
2
2
2
2
2
2
2
SPD Series for Integration into Electrical Distribution Equipment
Product Description
Eatons SPD Series surge

surge protectors. SPD Series
units are available in all
common voltages and
configurations, and also in
a variety of surge current
capacity ratings from
50 to 400 kA.
The SPD Series is available as

an integrated device within
the following Eaton electrical
assemblies:
Panelboards
Switchboards
Motor control centers
Switchgear
Automatic transfer
switches
Bus plugs
Features, Benefits
and Functions

technology
options
10-year warranty
(15-year with online
registration)
The Integrated SPD

Performance Advantage
Installation conductor length
is the single most important
factor related to an SPDs
performance. Performance
decreases as the connected
conductor length increases.
Integrating the SPD within the
electrical assembly provides
the best possible surge
protection by keeping
installation conductor lead
lengths as short as possible.
Integrating the SPD within
an electrical assembly can
decrease let-through
voltages by hundreds of volts,
providing you with the best
possible surge protection for
sensitive electronic loads.
2
2
2
2
2
2
In this installation, the SPD Series
is mounted directly to the panelboards
bus bars. This type of installation
will provide the best possible surge
protection by minimizing the
connected lead length.
2
2
2
2
Remote Display Mounting

Option Available
The SPD Series offers the
option of mounting its display
remotely from the device.
This is useful for applications
where OEMs or other
integrators would like to
embed the unit within a piece
of equipment and still be able
to view its display.
2
2
2
2
2
The SPD Series is also available as an
integrated unit interfaced via a circuit
breaker resident in the electrical
assembly. This installation keeps
connected lead lengths short while
providing a means of disconnecting
power to the unit quickly and easily.
V3-T2-7
2
2
2
2.1
2
2
2
2
2
UL 1449 4th Edition

recognized component
for the United States
and Canada, covered by
Underwriters Laboratories
certification and follow-up
service
UL 1283 5th Edition
(Type 2 SPDs only)
2
2
2
Catalog Number Selection
SPD Series Units Mounted Internal to Electrical Distribution Equipment
SPD 250 480D 2 J
2
2
2
2
2
2
2
kA Rating
050 = 50 kA per phase
ApplicationIntegrated Units 2
Series
SPD = Surge protective device
A = Panelboards (PRL1a, 2a, 3a, 3E), direct bus mounted

B = Switchgear (includes remote display)
C = Panelboards (PRL1a, 2a, 3a, 3E, 4), switchboards,
busway
J = Motor control centers
Voltage Code
240S = 120/240 single split-phase
208Y = 120/208 wye (4W+G)
220Y = 127/220 wye (4W+G)
400Y = 230/400 wye (4W+G)
480Y = 277/480 wye (4W+G)
600Y = 347/600 wye (4W+G)
240D = 240 delta (3W+G)
480D = 480 delta (3W+G)
600D = 600 delta (4W+G)
240H = 240 high-leg delta (4W+G) on B phase 1
Feature Package
1 = Basic
2 = Standard
3 = Standard + surge counter
Notes
1 Please consult the factory for 240 high-leg delta (4W+G) applications with high leg on C phase.
2 Units used in PRL1a, 2a, 3a and 3E panelboard applications are available in 50200 kA ratings only. Use the C option for
PRL1a, 2a, 3a and 3E panelboard applications when unit is connected through a circuit breaker.
Example: SPD250480D2J = SPD Series, 250 kA per phase, 480D voltage, standard feature package, motor control center application.
2
2
2
2
2
2
2
2
2
2
2
V3-T2-8

2.1
Technical Data and Specifications
2
2
SPD Series Specifications

Description
Specification
Surge capacity ratings available
50, 80, 100, 120, 160, 200, 250, 300, 400 kA per phase
2
2
Nominal discharge current (In)
20 kA (maximum rating assigned by UL)
Short-circuit current rating (SCCR)
200 kA
SPD type
Basic feature package = Type 1 (can also be used in Type 2 applications)

Standard and standard with surge counter feature packages = Type 2
2
2
Single split-phase voltages available
120/240
Three-phase wye system voltages available
120/208, 127/220, 230/400, 277/480, 347/600
Three-phase delta system voltages available
240, 480, 600
Input power frequency
50/60 Hz
208Y, 220Y, 240S, 240D and 240H voltage codes
0.5 W
400Y, 480Y and 480D voltage codes
1.1 W
600Y and 600D voltage codes
1.3 W
0.6 W
400Y, 480Y and 480D basic voltage codes
1.7 W
2.1 W
Power consumption (basic units):
Power consumption (standard and standard with surge counter units):
Protection modes
Single split-phase
L-N, L-G, N-G, L-L
Three-phase wye
L-N, L-G, N-G, L-L
Three-phase delta
L-G, L-L
Three-phase high-leg delta
L-N, L-G, N-G, L-L
2
2
2
Maximum continuous operating voltage (MCOV):

240S, 208Y, 220Y and 240H MCOV
150 L-N, 150 L-G, 150 N-G, 300 L-L
400Y and 480Y MCOV
320 L-N, 320 L-G, 320 N-G, 640 L-L
600Y MCOV
420 L-N, 420 L-G, 420 N-G, 840 L-L
240D MCOV
320 L-G, 320 L-L
480D MCOV
640 L-G, 640 L-L
600D MCOV
840 L-G, 840 L-L
Ports
Operating temperature
40 F through 122 F (40 C through 50 C)
Operating humidity
5% through 95%, noncondensing
Operating altitude
Up to 16,000 ft (5000 m)
2
2
2
2
2
2
Seismic withstand capability
Meets or exceeds the requirements specified in IBC 2006, CBC 2007 and UBC Zone 4
Form C relay contact ratings
150 Vdc or 125 Vac, 1 A maximum
Form C relay contact logic
Power ON, normal stateNO contact = open, NC contact = closed

Power OFF or fault stateNO contact = closed, NC contact = open
EMI/RFI filtering attenuation
Up to 50 dB from 10 kHz to 100 MHz
2
2
2
2
2
2
2
V3-T2-9
2.1
Approximate Dimensions in Inches (mm)

50200 kA Integrated Units
Mounting
8.80
(223.5)
2.02
(51.2)
0.95
(24.1)
2
2
3.42
(86.9)
NEUTRAL
2.52
(64.0)
SPD Series
Surge Protective Device
SURGE
GROUND
SURGE GROUND
Terminals
8.74
(222.0)
3.45
(87.6)
250400 kA Integrated Units

Mounting
8.80
(223.5)
3.42
(86.9)
4x Mounting
2.52
(64.0)
SURGE GROUND
4.85
(123.2)
5.78
(146.8)
2
2
SURGE
GROUND
5.40
(137.2)
CAUTION
4.66
(118.4)
TORQUE
1.71
(43.4)
NEU/GND
36 IN. LBS.
SPD Series
TORQUE
Mounting
3.42
(86.9)
FORM C CONTACTS
3.42
(86.9)
4x #1032 x 0.38 DP
Brass Terminals
9.50
(241.3)
NEU/GND
36 IN. LBS.
NEUTRAL
NEUTRAL
NEUTRAL
0.22
4x Mounting
(5.6)
3.42
(86.9)
0.26
(6.6)
NEUTRAL
4.66
(118.4)
NEU/GND
36 IN. LBS.
SURGE
GROUND
5.40
(137.2)
TORQUE
2
2
NEUTRAL
CAUTION
Mounting
3.42
(86.9)
2
2
2.02
(51.2)
FORM C CONTACTS
Bus 0.34
(8.6)
0.04
(1.0)
SURGE
GROUND
4.40
(111.8)
0.19
4x Mounting
(4.8)
NEUTRAL
0.22 3x Bus Mounting

(5.6)
SURGE
GROUND
Dimensions
SURGE GROUND
NEUTRAL
Terminals
8.74
(222.0)
9.50
(241.3)
Weights
50200 kA units
approximately 3.5 lb
(1.6 kg)
250400 kA units
approximately 7.0 lb
(3.2 kg)
2
2
V3-T2-10
0.22
4x Mounting
(5.6)
4x #1032 x 0.38 DP
Brass Terminals

Eaton SPD Series Sidemount Unit Mounted Externally to an Eaton Panelboard
2.1
Contents
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Distribution Equipment
Technical Data and Specifications. . . . . . . . . . . .
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-2
V3-T2-5
V3-T2-7
2
2
2
2
V3-T2-12
V3-T2-13
V3-T2-14
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
2
2
2
2
2
2
2
SPD Series for Mounting External to Electrical Distribution Equipment
Product Description
Eatons sidemount versions

of the SPD Series surge
UL 1449 4th Edition listed
surge protectors. Application
of SPD Series units
throughout a facility will
ensure that equipment is
protected with the safest and
most reliable surge protective
devices available. Units are
available in all common
voltages and configurations,
and also in a variety of surge
current capacity ratings from
50 through 400 kA. Three
feature package options are
also available to choose from.
Features, Benefits
and Functions
Uses self-protected metal

oxide varistor (MOV)
technology
options
10-year warranty
(15-year with registration)
UL 1449 4th Edition

listed device
Canadian Standards
Association (CSA)
UL 1283 5th Edition
(Type 2 SPDs only)
2
2
2
2
All SPD Series sidemount units come
prewired and include a factoryinstalled conduit interface,
making installation very easy.
2
2
2
2
2
2
All SPD Series units are factory sealed,

ensuring that the user/installer has
no potential of coming into contact
with harmful voltages present
inside the unit.
2
2
2
2
2
V3-T2-11
2.1

SPD Series Units for Mounting External to Electrical Distribution Equipment
SPD 250 480D 2 K
2
2
kA Rating
2
2
2
2
2
ApplicationSidemount Units
Series
SPD = Surge protective device
Voltage Code
240S = 120/240 single split-phase
208Y = 120/208 wye (4W+G)
220Y = 127/220 wye (4W+G)
400Y = 230/400 wye (4W+G)
480Y = 277/480 wye (4W+G)
600Y = 347/600 wye (4W+G)
240D = 240 delta (3W+G)
480D = 480 delta (3W+G)
600D = 600 delta (4W+G)
240H = 240 high-leg delta (4W+G) on B phase 1
Notes
2 NEMA 1 flushmount units are available in 50200 kA ratings only.
Example: SPD250480D2K = SPD Series, 250 kA per phase, 480D voltage, standard feature package, housed in NEMA 1 enclosure.
K
L
M
N
O
P
Q
=
=
=
=
=
=
=
NEMA 1 enclosure
NEMA 1 flushmount enclosure 2
NEMA 1 enclosure with internal disconnect
NEMA 4 enclosure
NEMA 4 enclosure with internal disconnect
NEMA 4X enclosure (stainless steel)
NEMA 4X enclosure with internal disconnect
(stainless steel)
Feature Package
1 = Basic
2 = Standard
3 = Standard + surge counter
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-12

2.1
SPD Series Specifications

Description
Specification
Surge capacity ratings available
50, 80, 100, 120, 160, 200, 250, 300, 400 kA per phase
20 kA (maximum rating assigned by UL)
200 kA
SPD type

Standard and standard with surge counter feature packages = Type 2
Single split-phase voltages available
120/240
120/208, 127/220, 230/400, 277/480, 347/600
Three-phase delta system voltages available
240, 480, 600
50/60 Hz
2
2
Power consumption (basic units):

0.5 W
400Y, 480Y and 480D voltage codes
1.1 W
1.3 W
0.6 W
1.7 W
Power consumption (standard and standard with surge counter units):
2.1 W
Protection modes
Single split-phase
L-N, L-G, N-G, L-L
Three-phase wye
L-N, L-G, N-G, L-L
Three-phase delta
L-G, L-L
Three-phase high-leg delta
L-N, L-G, N-G, L-L
2
2
2

240S, 208Y, 220Y and 240H MCOV
150 L-N, 150 L-G, 150 N-G, 300 L-L
400Y and 480Y MCOV
320 L-N, 320 L-G, 320 N-G, 640 L-L
600Y MCOV
420 L-N, 420 L-G, 420 N-G, 840 L-L
240D MCOV
320 L-G, 320 L-L
480D MCOV
640 L-G, 640 L-L
600D MCOV
840 L-G, 840 L-L
Ports
40 F to 122 F (40 C to 50 C)
Operating humidity
Operating altitude
Up to 16,000 ft (5000 m)
Seismic withstand capability
Meets or exceeds the requirements specified in IBC 2006, CBC 2007 and UBC Zone 4
Enclosure dimensions and weights
Refer to figures on Pages V3-T2-14V3-T2-15 for enclosure dimensions and weights
150 Vdc or 125 Vac, 1 A maximum
Power ON, normal stateNO contact = open, NC contact = closed

Power OFF or fault stateNO contact = closed, NC contact = open
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-13
2.1
2
2
2

Dimensions
50200 kA Units in a NEMA 1 Rated Flushmount Enclosure,
Weight = 6.8 Lb
50200 kA Units in a NEMA 1 Rated Enclosure,

Weight = 6.8 Lb
7.28
(184.9)
5.27
(133.9)
1.00
(25.4)
7.28
(184.9)
5.27
(133.9)
Flushmount Panel
(4) #832 Flat Hd Screws
2
2
2
10.48
(266.2)
10.48
(266.2)
12.05
(306.1)
5.24
(133.1)
2
2
0.78
(19.8)
2
2
2.00
(50.8)
3.48
(88.4)
4.41
(112.0)
0.40
(10.2)
250400 kA Units in a NEMA 1 Rated Enclosure,

Weight = 13.5 Lb
5.47
(138.9)
14.00
(355.6)
0.20
(5.1)
7.47
(189.7)
12.05
(306.1)
11.25
(285.8)
0.68
(17.3)
5.24
(133.1)
0.20
(5.1)
8.00
(203.2)
11.25
(285.8)
0.68
(17.3)
1.00
(25.4)
0.78
(19.8)
2.00
(50.8)
3.48
(88.4)
4.41
(112.0)
5.00
(127.0)
7.47
(189.7)
11.00
(279.4)
0.11
(2.8)
1.76
(44.7)
0.40
(10.2)
0.98
(24.9)
50400 kA Units in a NEMA 1 Rated Enclosure with Internal

Disconnect, Weight = 14.7 Lb
1.00
(25.4)
9.14
(232.2)
6.69
(169.9)
2
2
2
2
2
2
12.05
(306.1)
10.48
(266.2)
2.00
(50.8)
5.76
(146.3)
6.69
(169.9)
0.20
(5.1)
0.66
(16.8)
12.30
(312.4)
7.47
(189.7)
0.40
(10.2)
0.78
(19.8)
2.75
(69.9)
0.20
(5.1)
5.76
(146.3)
6.55
(166.4)
2
2
2
2
2
2
2
2
V3-T2-14
11.50
(292.1)
10.73
(272.5)
2.61
(66.3)
0.67
(17.0)
5.24
(133.1)
0.78
(19.8)
11.25
(285.8)
11.14
(283.0)
2.1


50400 kA Units in a NEMA 4 or 4X Rated Enclosure with
Internal Disconnect, Weight = 27.5 Lb
13.50
(342.9)
SPD Series
12.50
(317.5)
10.98
(278.9)
11.28
(286.5)
0.76
(19.3)
0.65
(16.5)
2.60
(66.0)
6.00
(152.4)
8.65
(219.7)
5.39
(136.9)
0.33
(8.4)
3.36
(85.3)
10.18
(258.6)
7.68
(195.1)
12.47
(316.7)
0.33
(8.4)
2
2
SPD Series
11.75
(298.5)
0.76
(19.3)
0.65
(16.5)
4.10
(104.1)
7.68
(195.1)
SPD Series
5.49
(139.4)
2
2
11.28
(286.5)
12.50
(317.5)
2
2
250400 kA Units in a NEMA 4 or 4X Rated Enclosure,

Weight = 14.6 Lb
10.98
(278.9)
2
2
0.65
(16.5)
0.76
(19.3)
2
2
12.28
(311.9)
SPD Series
5.49
(139.4)
12.75
(323.9)
11.98
(304.3)
3.12
(79.2)
11.75
(298.5)
SPD Series
SPD Series
50200 kA Units in a NEMA 4 or 4X Rated Enclosure,

Weight = 14.6 Lb
6.00
(152.4)
8.65
(219.7)
2
2
0.33
(8.4)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-15
2.1
2

Contents
SPD MAX
Description
Page
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Distribution Equipment . . . . . . . . . . . . . .
SPD MAX Series Surge Protection . . . . . . . . . . . . . .
Catalog Number Selection. . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPC Surge Protective Device
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electronic Voltage Regulator (EVR) . . . . . . . . . . . . . .
Power-Sure 800. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
2
2
2
2
2
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-17
V3-T2-18
V3-T2-19
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
2
2
SPD MAX Series Surge Protection
Product Description
Features
Eatons SPD MAX Series

side-mounted surge
surge protectors. Applying
SPD MAX Series units at
main service entrances and
critical loads will ensure that
equipment is protected with
the safest and most reliable
surge protective devices
(SPDs) available. Units are
available in all common
voltages and configurations,
and also in a variety of surge
100 kA through 800 kA.
Additionally, you may choose
from two feature package
options.
The breadth of the SPD MAX

Series features, options and
configurations ensures that
the correct unit is available for
all electrical applications,
including service entrances,
main switchgear, motor
control centers, distribution
switchboards, panelboards
and point-of-use applications.
2
2
2
2
2
2
2
2
2
2

technology
Lockout and tagout
provisions
Safety barriers
current (In) rating
(maximum rating assigned
by UL)
100 kA through 800 kA
surge current capacity
ratings
Installation flexibility, #10
to 1/0 wire may be used
Two feature package
options
rating (SCCR) (maximum
rating assigned by UL)
Field serviceable
15-year warranty standard,
additional 5 years with
product registration
2
2
2
2
V3-T2-16
UL 1449 3rd Edition

UL 1283 5th Edition
Canadian Standards
Association (CSA)
Built in an ISO 9001 facility
Designed and tested in
accordance with:
IEEE C62.41.1
IEEE C62.41.2
IEEE C62.43-2005
IEEE C62.45-2002
IEEE C62.48-2005
IEEE C62.62-2010

2.1
2
SPM 250 480D 3 R
SPM
Application Suffix
Series
kA Rating
Voltage Code Options 1

240S = 120/240 split-phase
208Y = 120/208 wye (4W+G)
220Y = 127/220 wye (4W+G)
400Y = 230/400 wye (4W+G)
600Y = 347/600 wye (4W+G)
240D = 240 delta (3W+G)
480D = 480 delta (3W+G)
600D = 600 delta (4W+G)
240H = 240 delta high-leg (4W+G) on B phase
230L = 230 single-phase
S =
T =
U =
V =
W=
X =
Y =
2 module, NEMA 4 enclosure with internal circuit breaker

1 module, NEMA 4 enclosure with internal terminal block
2 module, NEMA 4 enclosure with internal terminal block
1 module, NEMA 4X enclosure with internal circuit breaker
2 module, NEMA 4X enclosure with internal circuit breaker
1 module, NEMA 4X enclosure with internal terminal block
2 module, NEMA 4X enclosure with internal terminal block
2
2
2
2
Feature Package Options

1 = Basic
Dual-colored LED per phase to indicate protection status
Dual-colored LED to indicate protection status of the
NG mode on units with a neutral wire
3 = Standard with surge counter
Dual-colored LED per phase to indicate protection status
Dual-colored LED to indicate protection status of the
NG mode on units with a neutral wire
Audible alarm with silence button
Form C relay contact
EMI/RFI filtering that provides up to 50 dB of noise
attenuation from 10 kHz to 100 MHz
Surge counter with alarm silence (reset) button
2
2
2
2
2
2
2
2
Notes
SPD250480D3R = SPD MAX Series, 250 kA per phase, 480D voltage, standard with counter features package,
NEMA 4 enclosure with internal circuit breaker.
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-17
2.1
2
2
2
2
2
2


Description
Specification
Surge current capacity per phase
100 kA, 120 kA, 160 kA, 200 kA, 250 kA, 300 kA, 320 kA, 400 kA, 600 kA, 800 kA ratings available
20 kA
200 kA
SPD type

Standard with surge counter feature package = Type 2
Enclosure types
NEMA 4, NEMA 4X enclosure
Circuit breaker30 A
Eaton catalog number: FDC3030L
Terminal torque specifications
Circuit Breaker Load and Line

#10 AWG 35 lb-in; #8 AWG 40 lb-in; #6#4 AWG 45 lb-in; #31/0 AWG 50 lb-in
(SPD maximum wire range #101/0 AWG)
Standard split-phase voltages available
120/240
Single-phase
230
120/208, 127/220, 230/400, 277/480, 347/600
Three-phase delta system voltages
240, 480, 600
Three-phase high leg delta system voltages
120/240 high leg phase wire will be identified with a tag from the factory
50/60 Hz
208Y, 220Y, 230L, 240S, 240D and 240H voltage codes
0.6 W
1.7 W
2.1 W
Protection modes
Single split-phase LN, LG, NG, LL, single-phase LN, LG, NG, three-phase delta LG, LL,
three-phase wye LN, LG, NG, LL, three-phase high leg delta LN, LG, NG, LL
Maximum Continuous Operating Voltage (MCOV)
Power Consumption (Standard with Surge Counter Units)
230 V single-phase
320 V LN, 320 V LG, 320 V NG
127 V/220 V wye, 120 V/240 V single split phase
150 V LN, 150 V LG, 150 V NG, 300 V LL
120 V/240 V hi leg
150 V LN, 150 V LG, 150 V NG, 300 V LL, 320 V HN, 320 V HG, 470 V HL
230 V/400 V wye, 277 V/480 V wye
320 V LN, 320 V LG, 320 V NG, 640 V LL
347 V/600 V wye
420 V LN, 420 V LG, 420 V NG, 840 V LL
240 V delta
300 V LG, 300 V LL
480 V delta
640 V LG, 640 V LL
600 V delta
840 V LG, 840 V LL
Ports
1 or 2
Operating temperature and humidity
20 C through +50 C (4 F through +122 F), 5% through 95%, noncondensing
Storage temperature
20 C through +50 C (4 F through +122 F)
Operating altitude
Up to 16,000 ft (5000 m)
Weight
Not to exceed 52 lb
Maximum 0.46 A, 150 Vac, 1 A, 30 Vdc
Form C terminal block ratings
Rated 300 V, 16 A, 3012 AWG solid or stranded wire. Torque range 57 lb-in
Power on, normal stateNO contact = OPEN, NC contact = CLOSED

Power off, fault stateNO contact = CLOSED, NC contact = OPEN
EMI/RFI filtering attenuation (standard with surge counter)
Standards / agency certifications
UL 1449 Edition 3standard for surge protective devices
2
2
UL 1283 Edition 5standard for EMI filters (Type 2 SPDs only)

CSA Electrical Notice No. 516 Edition 1surge/transient voltage suppressor (excludes 230 L voltage code)
2
2
2
CSA 22.2 NO. 8-M1986 Edition 4EMI filters

Warranty
15 years from the date of delivery to the purchaser, 20 years if the product is properly registered at www.eaton.com
RoHS compliant
Yes
V3-T2-18

2.1
Dimensions
Optional Entry
2 NPT Maximum
1 AWG Maximum
2.33
(59.2)
1.63
(41.4)
6.58
(167.1)
1.13
(28.7)
2
2
2
NPT Maximum
Form C Entry
12.00
(304.8)
Mounting Dimension
2
2
16.00
(406.4)
2 NPT Maximum
Optimal Entry
1 Maximum
2
2
16.75
(425.5)
Mounting
Dimension
17.50
(444.5)
17.50
(444.5)
2
2
8.00
(203.2)
2
2
Scale 1000
14.91
(378.7)
2.33
(59.2)
(4X) 0.31
(7.87)
1/420 Mounting
Hardware
2
2
NPT Maximum
Form C Entry
8.32
(211.3)
1.13
(28.7)
9.30
(236.2)
2
2
6.58
(167.1)
2.33
(59.2)
0.50
(12.7)
2
1.63
(41.4)
2 NPT Maximum
Optimal Entry
1 Maximum
13.00
(330.2)
14.00
(355.6)
2
2
2
V3-T2-19
2.1
2

Contents
SPC
Description
Page
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
2
2
2
2
2
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-21
V3-T2-22
V3-T2-23
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

Product Description
Eatons SPC Series surge

protective devices are UL,
1449 4th Edition, certified
surge protectors. Application
of SPC Series units
throughout a facility will
ensure that equipment is
protected with the safest and
most reliable surge protective
devices available. The
compact design and
NEMA 4X enclosure of the
SPC Series allows for
installation external to an
electrical assembly in a
variety of environments.
Surge eventsshort-term
transients in voltage
threatening critical
downstream equipment
happen for many reasons.
The most common source,
though, is internal devices
powering on and off: motors,
transformers, photocopiers,
fluorescent lighting ballasts,
light dimmers, fax machines
and more. They can also be
generated externally by
events like lightning, grid
switching or electrical
equipment in adjacent
buildings.
SPC Series units are available

in all common voltages and
configurations, and in a
variety of peak surge
50 through 200 kA per phase.
Several feature package
options, including filtering,
audible alarm and Form C
contacts, are available to
choose from. A range of
configurable options is
available to customize the
SPC Series features for most
electrical applications,
distribution panelboards and
point-of-use applications.
The SPC Series belongs to
Eatons complete family of
surge protection solutions,
providing coverage for any
application.
V3-T2-20
While seemingly innocent,

surge events can wreak
serious havoc on unprotected
and inadequately protected
facilities. They can disrupt,
damage or destroy sensitive
microprocessor-based
devices (computers,
programmable logic controls,
etc.), resulting in premature
aging of equipment, process
interruptions and catastrophic
failures.
Features
The best way to prevent
downtime from an electrical
surge is through facility-wide
cascaded surge protection at
all stages of the electrical
distribution system. When
properly installed, surge
protective devices can
mitigate problems with
susceptible equipment,
keeping it and its related
processes running reliably
without surge-related
disruptions.
Eatons SPC Series surge
protective device (SPD) is a
key component to your
cascaded protection strategy.
Its compact, flexible and
configurable to protect most
electrical applications,
distribution panelboards and
Thermally protected metal

oxide varistor (MOV)
technology
Tri-colored LED protection
status indicators
current (In) rating
(maximum rating in the UL
1449 4th Edition standard)
50 through 200 kA per
phase peak surge current
capacity ratings
Configure-to-order with
eight custom feature
combinations
Corrosion-resistant
NEMA 4X enclosure with
mounting feet
rating (SCCR)
Factory prewired with
36 inches of 10 AWG wire
No user-serviceable parts
or items requiring periodic
maintenance
5-year warranty that can be
extended to 10 years with
product registration at
Eaton.com/spc

2.1
UL 1449 4th Edition Type 1

and Type 2
UL 1283 6th Edition
(Feature packages: 2, 6, 7
and 8)
Canadian Standards
Association (CSA) Type 1
and Type 2
2
2
2
2
SPC
2
SPC 200 208Y 8 P
Series
SPC
kA Rating (Options)
Enclosure
P = NEMA 4X
120N
240N
277N
480N
240S
240D
480D
600D
240H
208Y
415Y
480Y
600Y
=
=
=
=
=
=
=
=
=
=
=
=
=
Voltage Code (Options)

120 V single-phase (2 W +G)
120/240 V split-phase (3 W +G)
240 V delta (3 W +G)
240 V high leg delta (4 W +G)
120/208 V wye (4 W +G)
240/415 V wye (4 W +G)
277/480 V wye (4 W +G)
347/600 V wye (4 W +G)
2
2
Features
1=
2=
3=
4=
5=
6=
7=
8=
Options
No options (standard configuration)
Filtering, UL 1283 5th Edition
Audible alarm
Form C relay
Audible alarm and Form C relay
Filtering and audible alarm
Filtering and Form C relay
Filtering, audible alarm and Form C relay
SPD
Application
Type 1
Type 2
Type 1
Type 1
Type 1
Type 2
Type 2
Type 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-21
2.1

SPC
Description
Specification
Peak surge current capacity ratings available
50, 80, 100, 120, 150, 160, 200 kA per phase
20 kA
200 kA
Single-phase voltages available (2 W + G)
120, 240, 277, 480
Split-phase voltages available (3 W +G)
120/240
Three-phase wye system voltages available (4 W + G)
120/208, 240/415, 277/480, 347/600
Three-phase delta system voltages available (3 W + G)
240, 480, 600
Three-phase high leg delta system voltage available (4 W + G)
240
50/60 Hz
Protection modes
Single-phase: L-N, N-G, L-G

Split-phase: L-N, N-G, L-G, L-L
Wye: L-N, N-G, L-G, L-L
Delta: L-G, L-L
2
2

120N
150 L-N, 150 L-G, 150 N-G
240N, 277N
320 L-N, 320 L-G, 320 N-G
480N
550 L-N, 550 L-G, 550 N-G
240S, 208Y
150 L-N, 150 L-G, 150 N-G, 300 L-L
240H
150 L-N, 150 L-G, 150 N-G, 300 L-L, 470 H-L, 320 H-N, 320 H-G
415Y and 480Y
320 L-N, 320 L-G, 320 N-G, 640 L-L
600Y
320 L-N, 320 L-G, 320 N-G, 840 L-L
240D
320 L-G, 300 L-L
480D
550 L-G, 640 L-L
600D
840 L-G, 840 L-L
Ports
40 F to 140 F (40 C to 60 C)
Storage temperature
40 F to 140 F (40 C to 60 C)
Operating humidity
Operating altitude
Up to 2000 m (6561 ft)
Agency certification/listing
UL 1449 4th edition, UL 1283 6th edition, CSA C22.2 No. 269.1-14 for Type 1 SPD,
CSA C22.2 No. 269.2-13 for Type 2 SPD, CSA C22.2 no. 8-13 for EMI Filter
Durability Repetitive Strike Test
Passed 15,000 strikes to ANSI/IEEE C62.41 (20 kV, 10 kA) Category C Waveform
SPD type
UL 1449 4th edition and CSA Type 1 and Type 2 SPD (dependent on feature options)
Enclosure dimensions and weights
Refer to Page V3-T2-23 for enclosure dimensions and weights
Enclosure rating
NEMA 4X enclosure 1
2A at 30 Vdc or 250 Vac
Power ON, normal state; NO contact = open, NC contact = closed

Power OFF or fault state; NO contact = closed, NC contact = open
2
2
2
2
RoHS compliant
Yes
Warranty
5 years standard, 10 years with product registration on www.eaton.com/spc
SPC voltage configurations per enclosure size

P1 Enclosure
P2 Enclosure
120N/240N/277N/480N = 50200 kA
240S = 120200 kA
240S = 50100 kA
208Y/415Y/480Y/600Y = 120200 kA
208Y/415Y/480Y/600Y = 50100 kA
240D/480D = 120200 kA
240D/480D = 5000 kA
600D = 50200 kA
240H = 50100 kA
240H = 120200 kA
2
2
Note
1 Mounting feet required to achieve NEMA 4X rating.
V3-T2-22

2.1
Dimensions
P1
2
2
3.75
(95.3)
36-inch
long wires
Mounting feet
(included)
0.75 (19.1)
Locknut
3/4-14 NPS
external thread
1.00 (25.4)
6.00
(152.3)
Lid
1.12 (28.5)
ID508
5.50 (139.6)
Lid
6.62 (168.1)
4x #8 [m 4]
Flathead screw
(not included)
Overall base
including
stabilization ribs
5.56 (141.2)
2
2
2
3.19
(81.0)
2
2
7.13 (181.2)
0.16 (4.1)
Mounting feet
(included)
2
2
P2
2
3.75
(95.3)
8.50
(215.9)
Lid
2
2
36-inch
long wires
Mounting feet
(included)
7.50 (190.5) Lid
8.62 (219.0)
0.75 (19.1)
Locknut
3/4-14 NPS
external thread
1.00 (25.4)
2.38
(60.4)
4x #8 (m4)
Flathead screw
(not included)
7.56 (192.0)
overall base including
stabilization ribs
2
2
3.19
(81.1)
2
2
9.13 (232.0)
0.16 (4.1)
mounting feet
(included)
2
2
2
2
2
2
2
V3-T2-23
2.1
2

Contents
CVX050/100
Description
2
2
2
2
2
2
2
2
2
2
CVX050/100
Product Description
With over two decades of

experience in the surge
suppression industry and
extensive R&D initiatives,
Eaton is considered a world
leader in surge protective
device (SPD) manufacturing.
All of Eatons products are
manufactured in an ISO
9001:2000 and ISO 14001
certified facility.
Eatons CVX050 and CVX100

SPDs protect electronic
equipment from damaging
transients. These units are
suitable for medium and low
exposure level applications
that require cost-effective,
high quality system
protection including:
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100
Catalog Number Selection . . . . . . . . . . . . . . . .
Technical Data and Specifications . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
Eatons CVX050/100 models

are rugged, cost-effective,
high-quality SPDs that feature
self-protected MOVs that
eliminate the failure
characteristics of standard
metal oxide varistors. This
technology results in a fail-safe
device that monitors the
status of the metal oxide disk
and disconnects itself from the
power system when the disk
is approaching breakdown.
The CVX050/100 is easy
to install adjacent or even
internal to electrical
equipment. When installing an
SPD in a retrofit environment,
it is important to mount the
device as close to the
electrical equipment as
possible. Keep the wiring (lead
length) between the electrical
equipment and SPD as short
as possible, and twist or wire
tie the conductors together
to reduce the wires
impedance factor.
V3-T2-24
Residential/small business
Light industrial
Light commercial
Branch panel protection
OEM applications
Features, Benefits
and Functions
Advanced surge path

technology for high fault
current capacity, low
impedance, high frequency
design
Rugged NEMA 4X (IP65)
enclosure
Large diameter, selfprotected metal oxide
varistors provide long life
and fail-safe operation
LED monitoring of each
phase
Wide range of voltage
applications from
100 to 600 Vac and
48 and 125 Vdc
5-year free replacement
warranty
Optional Features
External mounting feet

(catalog number
MNTGFTX)
Flush mounting plate

(catalog number
FLUSHMNTPLATE12)
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-25
V3-T2-25
V3-T2-26
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
UL 1449 4th Edition for

surge protective devices
CE marked
Vibration tested IEC
60255-21-1 and -2
Note: CE, CSA and UL on

AC unit only.

2.1
CVX050/100
2
CVX 050 - 240S
Per Phase Peak
Surge Current
050 = 50 kA
100 = 100 kA
2
2
Configuration and Voltage Ranges

230L
480L
240S
240H
208Y
480Y
600Y
240D
480D
600D
048DC
125DC
= Single-phase200, 208, 220, 230, 240, 277 Vac

= Single-phase480 Vac
= Split-phase100/200, 110/220, 120/240 Vac
= Three-phase high leg delta120/240 Vac
= Three-phase wye (star)100/174, 110/190, 120/208, 127/220 Vac
= Three-phase wye (star)220/380, 230/400, 240/415, 277/480 Vac
= Three-phase wye (star)305/525, 347/600 Vac
= Three-phase delta200, 208, 220, 230, 240 Vac
= Three-phase delta380, 400, 415, 440, 480 Vac
= Three-phase delta525, 600 Vac (600D available in 50 kA only)
= Direct current48 Vdc 1
= Direct current125 Vdc 1
2
2
2
2
2
CVX050/100 Model Specifications

Description
Specification
Peak kA per phase
50, 100
Peak kA per mode
50
Nominal discharge current
20 kA 1
Short-circuit current rating
100 kA
Single-phase voltages
200, 208, 220, 230, 240, 277, 380, 400, 440, 460, 480 Vac
Split-phase voltages
100/200, 110/220/ 120/240 Vac
High leg delta voltages
240 Vac
Wye system voltages
100/175, 110/190, 120/208, 127/220, 220/380, 230/400, 240/415, 277/480, 305/525, 347/600 Vac
Delta system voltages

Direct current Voltage
2
2
2
2
2
2
200, 208, 220, 230, 240, 380, 400, 415, 440, 480, 525, 600 Vac
2
48 Vdc, 125 Vdc
47420 Hz (50/60 Hz typical)
Protection modes
Single-phase: L-N, N-G, L-G

Split-phase: L-N, N-G, L-G, L-L
High leg delta: L-N, N-G, L-G, L-L, H-N, H-G, H-L
Wye: L-N, N-G, L-G, L-L
Delta: L-G, L-L
Direct current 1 (DC): L-L, L-G
Number of ports
Specific energy
100 kJ/Ohm
Weight
2.0 lb (1.0 kg)
13 F (25 C) to +140 F (+60 C)
Vibration tested
IEC 60255-21-1 and IEC 60255-21-2
2
2
2
2
2
2
2
Notes
1 480L, 600D and 600Y units rated 10 kA I .
n
2 DC models only available in 50 kA.
2
2
2
2
2
2
V3-T2-25
2.1
2
2

CVX050/100 Voltage Ratings

System
Configuration
Model
UL 1449-3 VPR 1
MCOV
Nominal
System Voltage
L-L
L-N
L-G
N-G
L-L
L-N
L-G
N-G
CVX050
230L
Single-phase two-wire + ground
200, 208, 220, 230, 240, 277
320
640
320
1200
1200
1200
480L
380, 400, 440, 460, 480
550
1100
550
1800
4000
1800
240S
Split-phase three-wire + ground
100/200, 110/220, 120/240
300
150
300
150
1200
700
1200
800
208Y
Three-phase wye (star) four-wire + ground
100/175, 110/190, 120/208, 127/220
300
150
300
150
1200
700
1200
800
480Y
220/380, 230/400, 240/415, 277/480
640
320
640
320
2500
1200
2000
1200
600Y
305/525, 347/600
840
420
840
420
2500
1500
2500
1500
240D
Three-phase delta three-wire + ground
200, 208, 220, 230, 240
640
320
2000
1200
240H
Three-phase high leg delta
240
300
150
150
640
1500
700
1200
700
480D
380, 400, 415, 440, 480
1100
550
3000
1800
600D
525, 600
1100
700
3000
2500
048DC
Direct current
48 Vdc 2
130
65
125DC
Direct current
125 Vdc 2
288
144
230L
200, 208, 220, 230, 240, 277
320
320
320
1200
1200
1200
480L
380, 400, 440, 460, 480
550
550
550
1800
1800
1800
240S
Split-phase three-wire + ground
100/200, 110/220, 120/240
300
150
150
150
1200
700
800
700
208Y
100/175, 110/190, 120/208, 127/220
300
150
150
150
1000
600
700
700
480Y
220/380, 230/400, 240/415, 277/480
640
320
320
320
1800
1200
1200
1200
600Y
305/525, 347/600
840
420
420
420
2500
1500
1500
1500
240D
200, 208, 220, 230, 240
640
320
1800
1200
240H
Three-phase high leg delta
240
300
150
150
150
1200
700
700
700
480D
380, 400, 415, 440, 480
1100
550
3000
1800
Dimensions
CVX050/100 Standard Dimensions
2
2
2
4.75 (120.6)
3.39 (86.1)
2
2
Lid Removed
2
2
2
Section A-A
2
2
1.00 (25.4)
3.55 (90.2)
0.17 (4.3)
(4) Mounting Holes
Under Lid
Conduit Fitting
0.75 (19.0) Internal
Taper Pipe Threads
5.67 (144.0)
4.75 (120.6)
4.17 (106.0)
2.37 (60.2)
CVX100
Mounting Hole Shafts

Dimensions are in Inches (mm)
Notes
1 UL 1449 3rd Edition VPR (voltage protection rating) test environment: All tests performed with 6-inch lead length, positive polarity.
2 DC units available in 50 kA only. Voltages shown are the maximum suggested operating voltages and are not UL certified.
V3-T2-26

2.1
Contents
SP1 Surge Protective Device
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-28
V3-T2-28
V3-T2-28
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
2
2
2
2
2
2
2
2

Product Description
Eatons SP1 is a UL 1449 3rd
Edition-listed surge protective
device that provides reliable,
cost-effective surge
protection. This Type 1 SPD
is capable of being installed
on either the line or the load
side of the service entrance
disconnect, and can be used
as a replacement for devices
formerly known as secondary
surge arresters or lightning
arresters, which could not be
manufactured after UL 1449
3rd Edition went into effect
on September 29, 2009.
The unit is available in many
common voltages and
configurations. Multiple
mounting options coupled
with a compact footprint
enables installation of the
SP1 in a wide range of
applications, including panelboards, loadcenters, pump
panels, control cabinets, and
other electrical assemblies
and applications.
Features
Installation and operation of
the SP1 is simple. The unit
comes pre-wired with 24.00
inches of 10-gauge wire and
is mounted via the half-inch
nipple that is molded into its
enclosure. Wall or DIN rail
mounting can also be
accomplished with the
addition of an optional kit.
When powered, the units
light-emitting diode (LED)
indicator reports the status of
the protection elements and
is active when all of them are
intact and providing
protection. Any loss of
protection is signaled when
the LED extinguishes.
Type 1 SPD capable of

installation on either the
line or the load side of the
service entrance
disconnect
current rating (In) on most
models
50 kA per phase surge
current capacity
Compact footprint
4.80-inch L x 2.90-inch W x
2.50-inch D
Pre-wired with 24.00
inches of 10-gauge wire
Half-inch nipple molded
into enclosure enables
quick and easy mounting
Optional kit enables wall or
DIN rail mounting
Two-year warranty
UL 1449 3rd Edition-listed

device
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-27
2.1
2
2


SP1
SP1 - XXXX
2
Series
Voltage Code
SP1
240S
208Y
480Y
600Y
240D
480D
600D
2
2
SP1MNTGKIT = optional wall or DIN rail mounting kit
(order separatelynot included with SP1 unit)
2
2
SP1
Dimensions
SP1
Description
Ratings
Surge current capacity per phase
50 kA
20 kA for SP1-240S, 208Y, 480Y,

240D and 480D
2
2
2
2
2
2
= 120/240 V single split-phase

= 120/208 wye
= 277/480 wye
= 347/600Y wye
= 240 delta
= 480 delta
= 600 delta
1/2" (12.7)
Straight Pipe Thread
1.35
(34.3)
10 kA for SP1-600Y and 600D

200 kA
SPD type
Type 1 (can also be used in Type 2 applications)
.79 (20.1)
System voltages available (Vac)

Single split-phase
120/240
Three-phase wye
120/208, 277/480, 347/600
Three-phase delta
240, 480, 600
3.95
(100.3)
Protection modes
Single split-phase and three-phase wye
L-N, L-L
Three-phase delta
L-G, L-L
Maximum continuous operating voltage (MCOV)
SP1-240S and SP1-208Y
150 L-N, 300 L-L
SP1-480Y
320 L-N, 640 L-G
SP1-600Y
420 L-N, 840 L-G
SP1-240D
300 L-G, 300 L-L
SP1-480D
640 L-G, 640 L-L
SP1-600D
840 L-G, 840 L-L
2.89
(73.4)

Enclosure rating
NEMA 4
20 C to 50 C (4 F to 122 F)
Operating humidity
595%, noncondensing
Operating altitude
Up to 16,000 ft (5000 m)
Agency certification and approvals
UL 1449 3rd Edition Listed device
Warranty
2 years
ANSI/UL 1449 3rd Edition Voltage Protection Ratings
Catalog Number
L-N
L-G
L-L
SP1-240S
600
N/A
1000
SP1-208Y
600
N/A
1000
SP1-480Y
1200
N/A
2000
SP1-600Y
1500
N/A
2500
SP1-240D
N/A
1000
1000
SP1-480D
N/A
2000
2000
SP1-600D
N/A
2500
2500
50/60 Hz
Protection Mode
V3-T2-28
2.46
(62.5)

2.1
Contents
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Product Selection . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100. . . . . . . . . . . . . . . . . . . . . . . . .
Surge Protection for Light Commercial and

UL 508A Panel Applications
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-30
V3-T2-30
V3-T2-30
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
The SP2 provides basic

surge protection for light
commercial electrical
systems and OEM equipment
requirements. The SP2 is
available in the most popular
voltage and system
configurations and delivers
superior surge protection
using MOV thermal
disconnect technology
that eliminates the need
for additional overcurrent
protection.
By providing surge
protection, the SP2 can
suppress the transients that
are prevalent throughout the
power distribution system to
support reliable operations in
applications including:
Features, Benefits and

Functions
HVAC systems
Control panels
Automation cabinets
Pumping systems
Lighting systems
Commercial facilities
Food processing
Warehouses
Retail facilities
Manufacturing operations
2
2
2
2
2
2
2
2
2
2

Product Description
Ease of installation
Compact design allows
for easy installation on an
electrical panel or meter
socket, or integrated into
control cabinets
Type 1 UL 1449 Third
Edition listed SP2s are
easily selected and
installed on the loadside
or lineside of the service
entrance overcurrent
protective device
Thermal disconnect
technology eliminates the
need for additional
overcurrent protection
Compact UV-resistant
NEMA 4X enclosure for
indoor or outdoor
applications
LED status indicators
provide surge protection
status at a glancegreen
when good, red to replace
Voltage-specific models
protect electrical systems
and equipment, improving
performance by more than
110% over one-size-fitsall economy surge
arresters
Compact enclosure takes
up less space and can be
installed in tight spaces
Can be used on singlephase, split-phase, wye,
delta, and high-leg delta
systems
All SP2 devices are
individually marked with a
serial number for easy
tracking and identification
Two-year warranty
UL 1449 Third Edition Type

1 SPD File No. E109835,
cULus
Built in an ISO 9001 facility
Flammability rating UL 94VO
accordance with:
IEEE C62.41.1
IEEE C62.41.2
IEEE C62.43-2005
IEEE C62.45-2002
IEEE C62.48-2005
IEEE C62.62-2010
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-29
2.1

Product Selection
SP2
Nominal
System
Voltage
Maximum Continuous
Operating AC Voltage
(MCOV)
System
Type
Voltage
Protection
Ratings (VPR)
120
150
Single-phase, two-wire
240
320
Single-phase, two-wire
120/240
150
240
2
2
2
Connection
Points
Catalog
Number
700 LN
SP2-120
1200 LN
SP2-240
Split-phase, three-wire
700 LN, 1200 LL
SP2-240S
320
Three-phase delta, three-wire + ground
1200 LG, 2500 LL
SP2-240D
480
550
Three-phase delta, three-wire + ground
1800 LG, 3000 LL
SP2-480D
120/208
150
Three-phase wye, three-wire + ground
700 LG, 1200 LL
SP2-208Y
277/480
320
1200 LG, 2500 LL
SP2-480Y
347/600
420
1500 LG, 2500 LL
SP2-600Y
SP2
Description
Specification
Markets
Light commercial and UL 508 A panels
Product warranty
2 years
System types
Single, split, delta, and wye
Nominal system voltage
120, 208, 240, 480, 600 Vac
Installation
Two-, three-, four-wire
Maximum continuous operating AC voltage
Matched to nominal voltage
MCOV
150550 Vac (see table above)
LN protection
Yes (single-phase units)
LL protection
Yes
LG protection
Yes (three-phase units)
Protection
Surges and transients
SCCR
200 kA
Nominal discharge current (8 x 20 s) In
10 kA
Maximum discharge current (8 x 20 s) Imax
45 kA per phase
2
2
2
Response time tA
<25 ns
Voltage protection ratings (VPRs)
See table above
Overcurrent device (if required by local code) Circuit breaker or fuse sized to protect wires per
local codes
Frequency
50/60 Hz
Operating status / fault indication
One bi-color LEDgreen (good) / red (replace)
Conductor gauge/length
10 AWG stranded copper / 18 inches
Mounting
Chase nipple ( NPS)
Enclosure rating
NEMA 4XUL 94-5VA
Degree of protection (installed state)
IP20 (finger-safe)
Install location
Indoor/outdoor
Circuit location
Lineside/loadside
Standards / agency information
UL 1449 Third Edition Type 1 Listed SPD

cULus, RoHS compliant
40 C to +65 C
Maximum operating altitude
12,000 ft (3657.6 m)
Weight
17 oz (476 g)
2
2
Dimensions
SP2 Enclosure
1.06 (26.9)
Diameter
1.69
(42.9)
3.38
(85.9)
1.69
(42.9)
2.06
(52.3)
2.06
(52.3)
4.13
(104.9)
3.19
(81.0)
4.06
(103.1)
" NPS
0.87
(22.1)
2
2
V3-T2-30

2.1
Contents
AEGIS Solutions
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AEGIS Powerline Filters
Features, Benefits and Functions . . . . . . . . . . . .
Standards and Certifications. . . . . . . . . . . . . . . .
Power-Sure 800 . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-32
V3-T2-33
V3-T2-33
V3-T2-34
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-46
2
2
2
2
2
2
2
2
2
2
2
2
2
2
AEGIS Powerline Filters

Product Description
Eaton AEGIS Series line

filters and surge protectors
are specifically designed to
protect sensitive electronics
from hazards that exist within
a facility. The AEGIS Series
hybrid filter reacts instantly to
changes in voltage regardless
of phase angle or polarity. In
comparison to other line
filters, this technology
provides a higher level of
suppression, reliability and
life expectancy.
By providing surge protection

and line filtering, AEGIS
devices can suppress the
noise and transients
prevalent throughout the
power distribution system to
support reliable operations in
applications including:
Instrumentation
Water treatment facilities
Pulp and paper operations
Refrigeration and heating
plants
Petrochemical and refinery
Food processing
Textiles
Automotive assembly
Manufacturing operations
No matter where transients

originate, the application of
AEGIS Series devices will
help protect sensitive
electronic equipment
including:
Programmable logic
controllers (PLCs)
Scanning devices
Automatic teller machines
(ATMs)
Cash registers
Alarm systems
Microprocessor-controlled
OEM products
Robotics
CAD/CAM systems
Control equipment
Medical electronics and
devices
Why Should Sensitive Electronic

Loads be Protected?
PLC manufacturers and
service technicians
recommend the use of power
line filters and surge
suppressors to prevent
downtime and equipment
damage due to surges and
electrical line noise. Studies
have shown that failure to
protect sensitive electronic
loads costs American
manufacturing and
commercial and service
industries over $39 billion per
year in lost time and revenue.
Preventing these losses is a
major cost-saving
opportunity.
2
2
2
2
2
2
2
2
2
2
2
AEGIS Series devices are

available in a variety of
common voltages and
configurations.
2
2
2
2
2
V3-T2-31
2.1
2
2
2
2
2
2
2
Compact design with

multiple mounting options
Meets new UL safety
standards for surge and
filtering protection
AC models available with
up to 80 kA surge current
capacity ratings
DIN rail mounting available
on most models
Contains no replaceable
parts or items that require
periodic maintenance
Alarm contact available
Five- to ten-year warranty

standard dependent on
model; warranty extended
an additional five years if
registered
The breadth of the AEGIS
Series features, options and
configurations ensures that
the correct unit is available
for all critical electrical
applications, including control
panels, security systems,
measurement systems,
lab equipment and other
The AEGIS PH Series Protects Critical

Loads up to 20 A
The AEGIS PV Series Protects Critical

Loads up to 5 A
AEGIS Summary
Specifications
PH
PV
CF
CN
Voltage
120/240 Vac
120/240 Vac
120/240 Vac
24/48 Vdc
120/240 Vac
24/48 Vdc
Current range
320 A
15 A
1060 A
30 A
DIN mounting
Yes
Yes
Yes 1
No
UL 1283 5th Edition & UL 1449 3rd Edition
Yes
Yes
Yes 2
Yes 2
No
2
2
2
Filtering
Yes
Yes
Yes
EMI/RFI filtering attenuation at 100 kHz
75 dB
50 dB
40 dB
N/A
L to G, L to N & N to G protection modes
Yes
Yes
Yes
Yes
Peak kA per phase / mode
60/30
40/20
80/40
80/40
UL nominal discharge current (In)
5 kA
5 kA
5 kA
5 kA
UL voltage protection rating (VPR) LG / LN 3
330/400
330/400
500/500
500/500
5 kA
5 kA
10 kA
10 kA
Alarm contacts
Yes
No
Yes 4
No
Standard warranty / registered warranty (years)
10/15
10/15
5/10
5/10
Communication line protection (UL 497A)
No
No
Yes 4
No
2
2
AEGIS PH and PV Series Hybrid Powerline Filters
Three-Wire Design has Normal and Common Mode Protection (L-N, L-G, N-G)
Primary
Surge
Protection
2
2
Power
Input
2
2
2
2
2
2
High
Frequenc
y
Series
Blocking
Inductors
High
Performance
Tracking Filter
Secondary
Surge
Protection
Optional
Form C
Contacts 5
Power
Output
Normal
Mode
Normal
Mode
N
G
Status
Indicator
Lights
LED
Form C
L
N
Common
Mode
Common
Mode
Notes
1 Optional on 10 A and 30 A models only.
2 120 Vac models only.
3 Ratings shown for 120 Vac models, other voltages listed in Technical Data.
4 Optional on 30 A and 60 A models only.
5 Available on the PH Series only.
2
V3-T2-32

2.1
AEGIS Products
UL 1449 Fourth Edition

UL 1283 Fifth Edition
Built in an ISO 9001
facility
accordance with:
IEEE C62.41.1
IEEE C62.41.2
IEEE C62.43-2005
IEEE C62.45-2002
IEEE C62.48-2005
IEEE C62.62-2010
2
2
2
2
2
2
2
2
AEGIS
2
AG
Product
Family/OEM
AG
2
2
Protection/Filtering
PH = Premium protection
with hybrid filtering
Voltage
120 = 120 Vac
240 = 240 Vac
PV = Premium protection
with filtering
120 = 120 Vac

240 = 240 Vac
CF = Critical protection
with filtering
120 = 120 Vac

230 = 230 Vac
240 = 240 Vac
024 = 024 Vdc
048 = 048 Vdc
CN = Critical protection
without filtering
120 = 120 Vac

230 = 230 Vac
024 = 024 Vdc
048 = 048 Vdc
Amperage
03 = 3 A
05 = 5 A
10 = 10 A
15 = 15 A
20 = 20 A
01 = 1 A
03 = 3 A
05 = 5 A
10 = 10 A
15 = 15 A
30 = 30 A
60 = 60 A
Options
2
2
2
DIN
DIN2
CP
RJ
=
=
=
=
DIN mount 1
DIN2 mount 2
Compact 3
Telcom protection
and Form C status
contacts 4
2
2
2
30 = 30 A
2
2
Notes
1 Not available for 10 A, 230 V or 240 V versions.
2 Only available for 10 A, 120 V or 240 V CF version.
3 Only available for 10 A, 120 V CF version.
4 Only available for 30 A and 60 A CF version.
2
2
2
2
2
2
2
2
2
V3-T2-33
2.1
2

AEGIS PH and PV
PH 120 Vac
PH 240 Vac
PV 120 Vac
Specifications
3, 5, 10, 15, 20 A
3, 5, 10, 15, 20 A
1, 3, 5 A
1, 3, 5 A
DIN mounting
Yes
Yes
Yes
Yes
UL 1283 5th Edition and UL 1449 3rd Edition
Yes
Yes
Yes
Yes
Filtering
Yes
Yes
Yes
Yes
75 dB
75 dB
50 dB
50 dB
LG, LN and NG protection modes
Yes
Yes
Yes
Yes
Peak kA per phase/mode
60/30
60/30
40/20
40/20
5 kA
5 kA
5 kA
5 kA
UL voltage protection rating (VPR) LG / LN / NG
330/400/330
600/700/600
330/400/330
600/700/600
MCOV
150
275
150
275
5 kA
5 kA
5 kA
5 kA
Alarm contacts
Yes
Yes
No
No
10/15
10/15
10/15
10/15
No
No
No
No
2
2
2
2
PV 240 Vac
AEGIS CF
CF 24 Vdc
CF 48 Vdc
CF 120 Vac
CF 240 Vac
Specifications
10 A
10 A
10 A
10 A
10 A
10 A
30 A
60 A
10 A
10 A
30 A
DIN mounting
Yes
No
Yes
No
Yes
No
Yes 1
Yes 1
Yes
No
No
Yes 1
UL 1283 5th Edition and

UL 1449 3rd Edition
Yes
Yes
Yes
Yes
Yes
UL 1283 4th Edition
Yes
Yes
Yes
Filtering
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes

at 100 kHz
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
40 dB
LG, LN and NG
protection modes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
6/2
6/2
20/6
20/6
30/10
40/20
80/40
80/40
30/10
24/8
56/24
56/24
UL nominal discharge
current (In)
N/A
N/A
N/A
N/A
3 kA
5 kA
5 kA
5 kA
3 kA
N/A
N/A
N/A
UL voltage protection rating

(VPR) LG / LN / NG
N/A
N/A
N/A
N/A
500/500/500
500/500/500
500/500/500
500/500/500
900/800/900
N/A
N/A
N/A
MCOV
30
30
50
50
150
150
150
150
275
275
275
275
Short-circuit current
rating (SCCR)
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
10 kA
Alarm contacts
No
No
No
No
No
No
No
No
No
No
No
No
Standard warranty /
registered warranty (years)
5/10
5/10
5/10
5/10
5/10
5/10
5/10
5/10
5/10
5/10
5/10
5/10
Communication line
protection (UL 497A)
No
No
No
No
No
No
Yes 1
Yes 1
No
No
Yes 1
Yes 1
2
2
2
2
2
Note
1 Optional.
2
2
2
2
V3-T2-34
60 A
2.1

AEGIS CN
24 Vdc
48 Vdc
120 Vac
240 Vac
Specifications
30 A
30 A
30 A
30 A
DIN mounting
No
No
No
No
UL 1283 5th Edition and UL 1449 3rd Edition
Yes
UL 1283 4th Edition
Yes
Filtering
No
No
No
No
N/A
N/A
N/A
N/A
LG, LN and NG protection modes
Yes
Yes
Yes
Yes
20/6
46/20
80/40
56/24
N/A
N/A
5 kA
N/A
UL voltage protection rating (VPR) LG / LN / NG
N/A
N/A
500/500/500
N/A
MCOV
30
50
150
275
10 kA
10 kA
10 kA
10 kA
Alarm contacts
No
No
No
No
5/10
5/10
5/10
5/10
No
No
No
No
2
2
2
2
2
2
2
2
2
2
Maximum EMI/RFI AttenuationMIL-STD-220
Model
10 kHz
100 kHz
1 MHz
10 MHz
100 MHz
Maximum
Attenuation
Frequency
AGPH120AG
30 dB
74 dB
76 dB
37 dB
36 dB
101 dB at 0.5 MHz
AGPV120AG
27 dB
56 dB
55 dB
36 dB
28 dB
66 dB at 0.085 MHz
AGCF12010-CP
16 dB
35 dB
62 dB
40 dB
50 dB
68 dB at 1.25 MHz
AGCF12010-DIN
16 dB
35 dB
56 dB
29 dB
51 dB
66 dB at 0.7 MHz
AGCF12010
17 dB
35 dB
64 dB
33 dB
51 dB
64 dB at 1.0 MHz
AGCF12030
24 dB
44 dB
58 dB
42 dB
53 dB
67 dB at 0.6 MHz
AGCF12060
20 dB
48 dB
53 dB
29 dB
46 dB
69 dB at 0.4 MHz
2
2
2
2
2
2
Let-Through Voltages Based on IEEE Std. C62.62-2010 Testing Waveforms 1

AEGIS Series
Test Impulse
AGPH120AG
AGPV120AG
AGCF12010
AGCF12010-DIN
AGCF12010-CP
AGCF12030AGx
AGCF12060AGx
AGCN12030
IEEE Category A
100 kHz ring wave
6000 V, 200 A
25 V
30 V
150 V
300 V
300 V
150 V
90 V
400 V
IEEE Category B
100 kHz ring wave
6000 V, 500 A
35 V
40 V
330 V
400 V
400 V
330 V
230 V
500 V
IEEE Category B
combination wave
6000 V, 3000 A
(UL 1449-3 VPR)
360 V
370 V
470 V
480 V
460 V
460 V
450 V
460 V
2
2
2
2
2
2
Note
1 All tests conducted on 120 Vac units.
2
2
2
2
2
2
V3-T2-35
2.1
2

Contents
Description
2
2
2
2
2
2
2
2
2
2
2
Product Description
2
2
2
2
2
2
2
2
2
2
2
2
2
The SRT2 power conditioner

prevents expensive
electrical downtime. The
SRT2 represents Eatons
state-of-the-art solution to
todays power conditioning
challenges.
Input A
Input A
Input A
600
400
200
0
-200
-400
-600
Voltage Sags
Generation
1. Fault occurs on
the transmission
or distribution
system
Events per Year

End
Users
Transmission
Distribution
6
5
Feeder
Breakers
End
User
2. Creates a sag
event for all
users on the
system
4
3
2
1
End User
50 0 0 5
2 1
20 10 6
2
V3-T2-36
A typical distribution system

customer experiences about
50 events per year when the
voltage drops below 90%,
and only about two events
per year when the voltage
drops below 30% of nominal.
The utility study concluded
that sags represented almost
all of the events experienced
at a typical facility.
10
Definition of Voltage Sag

A voltage sag is a sudden,
momentary decrease in
supply voltage. It can last
from a cycle to several
seconds. Voltage sags are
most often caused by faults
on the electrical transmission
or distribution system. They
can be caused by lightning
strikes, animal contact,
starting of large motors
or an internal fault within
a customers facility.
Voltage sags are experienced

10 to 20 times more
frequently than complete
outages. However, voltage
sags are equally disruptive
to sensitive equipment.
Regularity of Voltage Sags

EPRI conducted a two-year
study of power quality levels
on distribution systems in the
United States. A variation
event was recorded every
time the voltage dropped
below 90% of the nominal.
The results are shown below.
Deep, Single-Phase Sag
Depending on the proximity

to the fault, which can be
hundreds of miles away,
the voltage during the sag
is typically 40%90% of
nominal utility voltage. The
operation of circuit breakers,
fuses and reclosers limits
most sags to less than
15 cycles.
V3-T2-37
V3-T2-37
V3-T2-38
V3-T2-39
V3-T2-40
V3-T2-42
V3-T2-46
The ProblemVoltage Sags

and Brownouts
The ability of a plant to
ride-through voltage sags
can have a significant
impact on operations and
competitiveness. In the
United States, voltage sags
cost billions of dollars in
lost production, interruption,
damaged materials, retooling
and scrap. In addition,
sags can cause: increased
operating costs, the need
for product reworks, safety
hazards, equipment damage
and/or failure, reduced
product quality, increased
clean-up, additional labor
costs, increased scrap
material and costs associated
with investigations into
the problem.
Todays industrial and large

commercial electricity
customers are becoming
more sensitive to power
disturbances and are
demanding better electric
quality. However, the quality
of power grids is not
significantly improving.
Customers still experience
power quality problems
that affect plant operations
and profitability.
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
30
Eatons sag ride-through is

the first of its kind.
V3-T2-7
60
Page
V3-T2-2
V3-T2-5
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPC Surge Protective Device . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Application Description . . . . . . . . . . . . . . . . . . . .
Features, Benefits and Functions . . . . . . . . . . . .
Power-Sure 800. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . . .

Industries and Applications

Affected by Sags
Key industries:
Sag Correction Using the SRT2

The SRT2 is a high
performance, inverterbased voltage conditioning
device developed to provide
protection to sensitive loads
against commonly occurring
voltage sags.
Equipment or processes:
Semi-conductor
manufacturers
Communications
Steel mills
Petroleum and chemical
processing
Health care
Paper mills
Automotives
Textile
Printing
Plastics
Other manufacturing
Manufacturing process
controllers
Variable speed drives
Robotics
Motor conductor
Telephone systems
HID lighting
HVAC controls
Medical equipment
Computers
Block Diagram of the SRT2 Active Voltage Conditioner
3-Phase
Utility
Supply
3-Phase Compensating
Voltage
Secondary
Distribution
Transformer
Primary
3-Phase
Load
Voltage
Injection
Transformer
Bypass Circuit
SRT2 Input
SRT2 Output
Voltage Source
Inverter
The SRT2 monitors the

incoming supply voltage and
when it deviates from the
nominal voltage level, the
SRT2 achieves voltage
conditioning by injecting the
appropriate correction voltage
in series with the power
supply. The SRT2 provides an
extremely fast reaction time
and subcycle response to sag
events that would otherwise
cause loads to drop out.
The SRT2 is designed for
low voltage systems and
is also offered in medium
voltage applications from
up to 50 MVA. Installation is
simple and the SRT2 provides
customers with a new
solution to improve
productivity and reduce
downtime for sag related
problems.
The SRT2 meets the
stringent requirements
of the Semi-F47 standard;
a key requirement for SAG
correction in the semiconductor industry.
Complete correction
of single-phase voltage
sags down to 63% for
30 seconds
Partial correction of threephase sags down to 50%
for 30 seconds
Correction of utility voltage
unbalance (from network
side of transformer)
Attenuation of voltage
flicker
2.1
2
Continuous Regulation
The Sag Ride-Through is an
active voltage conditioner.
This means it will constantly
respond to voltage sags and
swells in the +/10% range
with a regulated output in the
+/1% range. The SRT2 can
be applied to the main service
entrance, at branch locations
or in front critical loads. The
SRT2 provides an outstanding
return on investment. It
delivers operation productivity
that is just not possible with
traditional tap switching or
ferroresonant technologies.
The SRT2 consists of a
voltage source inverter,
bypass circuit and an injection
transformer connected in
series between the incoming
utility supply and the load, as
shown in the figure below.
For the standard sag
correcting model, the
injection transformer consists
of a boost component. The
SRT2 monitors the incoming
supply voltage and when it
deviates from the nominal
voltage level the SRT2 inserts
an appropriate compensating
voltage using the IGBT
inverter and series injection
transformer. Energy is
sourced from the supply
during this time. This
regulates the load voltage
to its nominal value,
thus eliminating voltage
disturbances from the utility
supply affecting the load.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-37
2.1
2
2
2
2

Product Selection
SRT2 1
Load Capacity at
Nominal Voltage
480 V (kVA) 2
Terminal
Cabinet 3
Fault Capacity
(kVA)
System
Efficiency (%)
System Dissipation Airflow

(Worst Case) (kW) (m3/min)
Cabinet Dimensions H x W x D
in Inches (mm)
Catalog
Number 4
SRT20150480AA
150
No
40
97.5
3.8
18
85.00 x 32.00 x 32.00 (2159.0 x 812.8 x 812.8)
150
Yes
40
97.5
3.8
18
85.00 x 32.00 x 32.00 (2159.0 x 812.8 x 812.8)
SRT20150480AA-TC
225
No
40
97.7
5.2
18
85.00 x 32.00 x 32.00 (2159.0 x 812.8 x 812.8)
SRT20225480AA
225
Yes
40
97.7
5.2
18
85.00 x 32.00 x 32.00 (2159.0 x 812.8 x 812.8)
SRT20225480AA-TC
300
No
40
98.0
6.1
18
85.00 x 40.00 x 32.00 (2159.0 x 1016 x 812.8)
SRT20300480AA
300
Yes
40
98.0
6.1
18
85.00 x 40.00 x 32.00 (2159.0 x 1016 x 812.8)
SRT20300480AA-TC
SRT20450480AA
2
2
450
No
40
98.2
8.0
36
85.00 x 40.00 x 32.00 (2159.0 x 1016 x 812.8)
450
Yes
40
98.2
8.0
36
85.00 x 40.00 x 32.00 (2159.0 x 1016 x 812.8)
SRT20450480AA-TC
600
No
40
98.4
9.8
36
85.00 x 40.00 x 32.00 (2159.0 x 1016 x 812.8)
SRT20600480AA
600
Yes
40
98.4
9.8
36
85.00 x 40.00 x 32.00 (2159.0 x 1016 x 812.8)
SRT20600480AA-TC
750
No
40
98.4
12.2
54
85.00 x 96.00 x 48.00 (2159.0 x 2438.4 x 1219.2)
SRT20750480AA
750
Yes
40
98.4
12.2
54
85.00 x 96.00 x 48.00 (2159.0 x 2438.4 x 1219.2)
SRT20750480AA-TC
900
No
40
98.5
13.2
54
85.00 x 96.00 x 48.00 (2159.0 x 2438.4 x 1219.2)
SRT20900480AA
1200
No
40
98.5
18.1
72
85.00 x 126.00 x 96.00 (2159.0 x 3200.4 x 2438.4)
SRT21200480AA
1500
No
50
98.7
20.2
90
85.00 x 126.00 x 96.00 (2159.0 x 3200.4 x 2438.4)
SRT21500480AA
1800
No
50
98.8
22.1
108
85.00 x 126.00 x 96.00 (2159.0 x 3200.4 x 2438.4)
SRT21800480AA
2
2
SRT2 with External Maintenance Bypass Block Diagram
2
S3
2
2
2
AC
Supply
2
2
2
2
2
2
Load
S1
SPD
S2
SRT2
Note: A terminal cabinet may be needed if a bypass cabinet is not used. SRT2 units 900 kVA and
larger do not require a terminal cabinet; however, an external three-breaker mechanical bypass with
integrated surge protection is recommended.
Notes
1 For 50 Hz international applications, consult factory.
2 480 V is standard. If additional voltage is needed, consult factory.
3 Eaton external three-breaker maintenance bypass cabinet is recommended. If a bypass is not used, a terminal cabinet may be required. Contact factory.
4 TC in the model number denotes terminal cabinet, which is not required for units of 900 kVA and larger.
2
2
2
2
2
2
V3-T2-38

2.1
SRT2 Specifications
Features
Specifications
Load Capacity
Capacity
1501800 kVA (consult factory for custom design; up to 36 kVA available)
Displacement power factor of connected load
0 lagging to 0.9 leading
Crest factor for rated kVA
3 at 100% of rated load
Overload capacity (>90% supply voltage)
150%, 30 seconds, once per 500 s
2
2
Input Supply
Nominal supply voltage (according to model)
480 V
Voltages up to 36 kV available as custom applications 1
Power system type
Three-phase, center ground referenced
Supply voltage category
Level III transient voltage capability
Fault capacity
Refer to model tables
90110% of nominal input voltage unit rating
Nominal voltage (V)
Set to match nominal supply voltage
Three-phase V regulation range
10% continuous
Three-phase V regulation accuracy
1%
Three-phase balanced sag/swell correction ability:

40% model
+40% / 10% at least 30 s at full load
Sag correction accuracy (within specified range)
2.5%
Sag correction response:

Initial
Complete
<250 s
<0.25 cycle
Single-phase sag correction ability:

40% model (15% retained voltage / 85% sag)
90% nominal
Equivalent series impedance (operating)
<4% typical
Efficiency of system
0.98 to 0.99 (refer to model tables)
100% model rating (kVA)
125%
150%
500%
2000%
<0.5 ms
<2.5% typical
Ethernet connectivity; Modbus TCP, dry contacts
Enclosure rating
NEMA 1, IP20
Pollution degree rating
Operating Voltage Range for Regulation

Supply voltage for regulation
Output Supply
2
2
2
Bypass
Capacity
Maximum overload capacity (in bypass):
For 10 minutes
For 1 minute
For 1 second
For 200 milliseconds
Transfer time:
Inverter to bypass
Equivalent series impedance (in bypass)
Interface
Access protocol
Environmental
Minimum operating temperature
0 C
Maximum operating temperature
40 C
Temperature derating
Above 40 C derate at 2% per C to a maximum of 50 C
Capacity elevation derating
2% every 100 m above 1000 m
Cooling:
Inverter
Transformer
Forced ventilation
Fan assisted ventilation
Humidity
<95%, noncondensing
EMC emissions
CISPR 22 level G
Noise
65 dBA
Warranty
1 year
2
2
Note
1 480 V is standard. If additional voltage is needed, consult factory.
2
V3-T2-39
2.1
2

Electronic Voltage Regulator (EVR) Tap Changer
Contents
Description
Page
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CVX050/100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2
2
2
2
2
2
V3-T2-2
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-41
V3-T2-41
2
2
Product Description
2
2
2
2
2
2
2
2
2
2
2
2
2
Eatons Electronic Voltage

Regulator (EVR) is the ideal
solution for keeping your
facility and equipment up and
running during brownouts,
undervoltage conditions and
other power problems. The
EVR can significantly reduce
the costs of equipment
damage and downtime
when these situations occur.
The state-of-the-art design
provides rapid response time,
high efficiency, high inrush
current capability, and
operating advantages
exclusive to Eaton.
The EVR maintains a tightly
regulated output voltage by
automatically activating the
appropriate transformer tap
through a silicone controlled
rectifier (SCR). Tap changer
response time is initiated at
one cycle, ensuring rapid
and precise regulation.
Switching at zero current
enables noise reduction
during tap transitions.
2
2
2
2
Features and Benefits

Brownouts
In the United States, most
facilities have sufficient
voltage regulation. However,
in some U.S. locations and
many developing countries,
regulation problems occur
because of overstressed
utility distribution systems.
In some cases, due to the
excessive demand on the
utility system, voltage may
be below 10% of nominal
(10%) during the day. This
condition is called a voltage
dip or brownout. Customers
may notice dim lights and
reduced power. During the
evening, voltage may rise
above 10% of nominal
(+10%) because large
facilities and loads are shut
down. This shutdown
reduces the power demand
on the grid and results in a
voltage increase.
The Solution
Prior to installing an expensive
solution, Eaton encourages
customers to monitor
incoming voltage to
determine if voltage
regulation is a problem.
The local utility may also be
able to provide information
on voltage expected at
the facility.
Using a meter, it can quickly
be determined if a voltage
regulation problem or
brownout condition exists.
The appropriate solution
would be an EVR. EVRs can
be installed at the service
entrance, branch panel or
at critical loads.
Eatons EVR is a solid-state
tap changing power
conditioner designed to
protect against brownouts
and long duration voltage
regulation problems.
The IEEE defines voltage

regulation as overvoltage
or undervoltage. Voltage
regulation events last from
a few minutes to many
hours with voltage varying
by 20%. Long-term
regulation problems differ
from short duration sags and
dips, which are much deeper
voltage drops.
2
V3-T2-40
Coordinated with standard

thermal-magnetic breakers
to allow motor starts
Optional 50 kA or 100 kA
per phase surge protection
Input frequency range
operation from 5763 Hz
Integral manual rotary
maintenance bypass
switch standard on 50 to
500 kVA units and optional
on smaller units
Not affected by load power
factor. Can operate
effectively in low-load
applications due to unique
leakage reactance
technology
Fail-safe bypass circuit,
isolation transformer
and overtemperature
protection
Less than 1% THD
Optional Standard and
Premium metering to
monitor voltage, current,
frequency, power, energy,
PF with minimum
and maximum, and
communication capabilities

2.1
EVR
EVR XXX XXXX XXXX X X XX X

Options
B = Bypass switch 1
M1 = Standard metering (IQ 130)
M2 = Premium metering (IQ 150)
kVA Ratings and Dimensions

kVA
Weight
Lb
BTUs/
hr
Bypass
010
010
015
015
025
030
045
050
075
100
125
150
225
300
500
440
520
520
600
870
890
950
1,176
1,575
2,014
2,137
2,240
3,300
4,000
5,500
1,025
1,205
1,540
1,540
2,560
3,090
4,600
7,332
9,514
11,833
14,748
17,698
23,000
30,750
51,250
Optional
Optional
Optional
Optional
Optional
Optional
Optional
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Dimensions in Inches (mm)

(H x W x D)
Metering
No
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
30.20 x 22.20 x 29.00 (767.1 x 563.9 x 736.6)

44.20 x 22.20 x 29.00 (1122.7 x 563.9 x 736.6)
30.20 x 22.20 x 29.00 (767.1 x 563.9 x 736.6)
44.20 x 22.20 x 29.00 (1122.7 x 563.9 x 736.6)
44.20 x 22.20 x 29.00 (1122.7 x 563.9 x 736.6)
44.20 x 22.20 x 29.00 (1122.7 x 563.9 x 736.6)
44.30 x 45.90 x 29.00 (1125.2 x 1165.9 x 736.6)
66.00 x 29.00 x 35.50 (1676.4 x 736.6 x 901.7)
76.00 x 34.40 x 35.50 (1930.4 x 873.8 x 901.7)
76.00 x 34.40 x 35.50 (1930.4 x 873.8 x 901.7)
76.00 x 34.40 x 35.50 (1930.4 x 873.8 x 901.7)
76.00 x 34.40 x 35.50 (1930.4 x 873.8 x 901.7)
77.40 x 56.00 x 41.50 (1966.0 x 1422.4 x 1054.1)
77.40 x 56.00 x 41.50 (1966.0 x 1422.4 x 1054.1)
77.00 x 72.40 x 48.40 (1955.8 x 1839.0 x 1229.4)
Nominal Input
Voltage
(Delta Input:
L, L, L, G)
208D = 208
240D = 240
400D = 400
480D = 480
600D = 600
2
2
2
Surge Protection
X = No
S = Yes
2
2
Frequency
A = 60 Hz
B = 50 Hz
Nominal Output
Voltage
(Wye Output:
L, L, L, N, G)
2
2
208Y = 120/208
400Y = 230/400
480Y = 277/480
600Y = 347/600
2
2
EVR Specification (10 to 500 kVA)

Feature
Description
Technology
Electronic tap changer
Input voltages
208600 V, three-phase (three-wire)
Input voltage range
+10% to 23% of nominal rated input
Output voltage
3% of nominal
Response time
1/2 cycle
Frequency
60 Hz, 3%
Efficiency
97% typical
Line regulation
Output is 3% of nominal for input variations of +10% to 23% of nominal
2
2
2
2
2
2
Load regulation
Output is maintained within 3% of nominal from no load to full load
Correction time
Output will be corrected to within 3% of nominal in 1.5 cycles or less
Harmonic distortion
Less than 1.0% added to the output waveform under any dynamic linear loading conditions
presented to the line regulator
Noise attenuation
Common mode
Normal mode
146 dB
3 dB down at 1000 Hz, 40 dB/decade to below 50 dB with resistive load
Turn-on characteristics
When energized, voltage overshoot will be less than 5% of nominal for 1 cycle or less
Overload rating
1000% for 1 cycle and 200% for 10 seconds
Ambient rating
10 to 40 C
Monitoring
Three green LEDs (phase power on indication), one red LED (alert indication)
Surge protection (optional)
CVX 50 kA SPD device 50 kVA and below, CVX 100 kA SPD device 75 kVA and above
Input breaker
MCCB rated 125% of full rated current
Bypass switch
Normal and bypass selector
Metering (optional)
Standard metering (IQ 130)voltage and current with minimum and maximum
Warranty
2
2
2
2
Premium metering (IQ 150)voltage, current, frequency, power, energy, PF, with minimum
and maximum, communications capabilities
1-year parts
Notes
1 Bypass is standard on 50 kVA and larger units and an option on 45 kVA and smaller units. The B is not included in the part number for
units 50 kVA and larger.
All weights are approximate. Monitor option includes main input circuit breaker.
Refer to PAD for pricing and availability.
2
V3-T2-41
2.1
2

Contents
Power-Sure 800
Description
2
2
2
2
2
2
2
2
Superior Power Conditioning for Industrial and Commercial
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Page
Introduction
CVX050/100. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100 . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-43
V3-T2-44
V3-T2-45
V3-T2-45
V3-T2-46
Power-Sure 800
Product Description
Features
Eatons Power-Sure 800

cleans up and purifies
fluctuating and erratic power
that exists in commercial and
industrial facilities so that
sensitive electronic
equipment is not affected.
The Power-Sure 800 is

ideal for use in industrial
applications, such as
computer programmable
controllers and robotics.
Use the Power-Sure 800
whenever continuous, wellregulated, transient-free
power is required.
The Power-Sure 800 is a

self-regulating isolation
transformer. It was
developed to protect against
fluctuating voltages,
brownouts, line noise, shortduration power outages,
sags, surges, spikes and
transients. The Power-Sure
800 also has one of the
highest K-factorsK-30and
eliminates harmonic current
in the power line, which helps
prevent damage to building
wiring.
2
2
Superior isolation
Tight voltage regulation
High immunity to distortion
Lightning and surge
protection
Protection against power
interruptions
Power factor correction
Bi-directional harmonic
filtering
K-30 rated design
Warranty: two years
Eatons Power-Sure 800

power conditioners provide
high-quality power with
inherent surge protection,
noise and bi-directional
harmonic filtering, as well as
superior isolation. These units
range from office models to
floor- or wall-/panel-mounted
industrial models and provide
an excellent solution for any
application with noisy or poor
power quality.
2
2
2
2
2
V3-T2-42
UL 1012, UL 544
and cUL listed
Meets ANSI standards for
computers with inputs as
low as 50% of nominal
2.1

Power-Sure 800
T800 X - XXXXX X X - X
Configuration
R = Receptacles
P = Hardwired wall-/panel-mount
F = Hardwired floor-mount
VA rating
01000
01500
01600
02000
02100
02500
03000
03500
03501
05000
07500
08000
10000
15000
20000
25000
Option/Frequency
Blank = 60 Hz
5
= 50 Hz
Custom Receptacle Options

Receptacles
Quantity of:
Blank for
hardwire
Code
No. of Output
Panels (Max. 4)
A
B
C
D
E
F
G
H
I
J
K
L
M
N
P
R
S
T
U
V
W
X
Y
1
1
1
1
1.5
1
1
1
1
1.5
1.5
1
1.5
1
1
1
1
1
1
1
1
1
1
NEMA
Volts
(1) 5-15R
(2) 5-15R
(1) 5-20R
(2) 5-20R
(1) 5-30R
(1) 6-15R
(2) 6-15R
(1) 6-20R
(2) 6-20R
(1) 6-30R
(1) 6-50R
(1) 14-20R
(1) 14-30R
(1) L5-15R
(2) L5-15R
(1) L5-20R
(1) L5-30R
(1) L6-15R
(2) L6-15R
(1) L6-20R
(1) L6-30R
(1) L14-20R
(1) L14-30R
120
120
120
120
120
208/240
208/240
208/240
208/240
208/240
208/240
120/240
120/240
120
120
120
120
208/240
208/240
208/240
208/240
120/240
120/240
Amps
2
2
2
15
15
20
20
30
15
15
20
20
30
50
20
30
15
15
20
30
15
15
20
30
20
30
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-43
2.1
2
2
2
2

Product Selection
Power-Sure 800 Models

Rating (VA/Watts)
Input Voltage
Output Voltage
Input Interface
Output Interface
Part Number
Office Models (with Receptacles)

1000/700
120
120
5-15P
(4) 5-20R
T800R-01000
1600/1200
120
120
5-15P
(4) 5-20R
T800R-01600
2100/1500
120
120
5-20P
(4) 5-20R
T800R-02100
2500/1750
120
120
5-30P
(4) 5-20R
T800R-02500
3500/2450
120
120/240
5-50P
(4) 5-20R
T800R-03500
3500/2450
208/240
120/240
6-20P
(4) 5-20R
T800R-03501
5000/3500
208/240
120/240
Hardwired
Custom 1
T800R-05000
7500/5250
208/240
120/240
Hardwired
Custom 1
T800R-07500
10,000/7000
208/240
120/240
Hardwired
Custom 1
T800R-10000
15,000/10,500
208/240
120/240
Hardwired
Custom 1
T800R-15000
Industrial Models (Hardwired Wall-/Panel-Mount)

500/500
Range 1 24
Range 3 5
Hardwired
Hardwired
T800P-00500
750/750
Range 1 24
Range 3 5
Hardwired
Hardwired
T800P-00750
1000/1000
Range 1
24
Hardwired
Hardwired
T800P-01000
1500/1500
Range 1 24
Range 3 5
Hardwired
Hardwired
T800P-01500
2000/2000
Range 1 24
Range 3 5
Hardwired
Hardwired
T800P-02000
3000/3000
Range 1 24
Range 3 5
Hardwired
Hardwired
T800P-03000
5000/5000
Range 1 24
Range 3 5
Hardwired
Hardwired
T800P-05000
8000/8000
Range 2 34
Range 3 5
Hardwired
Hardwired
T800P-08000
10,000/10,000
Range 2 34
Range 3 5
Hardwired
Hardwired
T800P-10000
Range 3
Industrial Models (Hardwired Floor-Mount)

5000/5000
Range 1 24
Range 3 5
Hardwired
Hardwired
T800F-05000
8000/8000
Range 2
34
Range 3 5
Hardwired
Hardwired
T800F-08000
10,000/10,000
Range 2 34
Range 3 5
Hardwired
Hardwired
T800F-10000
15,000/15,000
Range 2 34
Range 3 5
Hardwired
Hardwired
T800F-15000
20,000/20,000
Range 2 34
Range 3 5
Hardwired
Hardwired
T800F-20000
25,000/25,000
Range 2 34
Range 3 5
Hardwired
Hardwired
T800F-25000
2
2
2
Notes
1 See Catalog Numbering Selection on Page V3-T2-43; 5 panels available for distribution; HW output utilizes 1 panel, other 4 panels can be used for receptacle interface or cabling.
2 Range 1: 120/208/240/480.
3 Range 2: 208/240/480.
4 Input and output voltage is field configurable; units will ship from the factory configured as follows: Range 1120 V (input/output); Range 2240 V (input/output).
5 Range 3: 120/208/240.
2
2
2
2
2
2
2
2
V3-T2-44

Line regulation: 3% V-out

for +10% to -20% V-in at
100% load
Load regulation: 3%for
075% load 2%for 100%
load
Immunity to distortion: at
40% THD V-in, 5% max.
THD V-out at 50% load or
higher
Ride-through capability:
1 cycle
Voltage recovery: 2 cycles
to 95%, 3 cycles to 100%
K-factor: K-30 rated
Power factor correction:
input of 0.95 typical
Harmonic attenuation:
23 dB for load-reflected
harmonics
2.1
Dimensions
Galvanic isolation: NEC
250.5d, 0.001 PF
Surge protection: 330 V
let-through voltage when
tested to ANSI/IEEE
62.41-Cat B3
Common mode noise
attenuation: 140 dB
Transverse mode noise
attenuation: 120 dB
Reliability: 200,000 hours
(MTBF)
Audible noise: 5256 dB
measured at 1 meter,
A scale
Efficiency: approximately
92% at full load
Operating temperature:
20 C to +40 C
2
Power-Sure 800 Models
Dimensions, W x D x H
Weight, Lb (kg)
Part Number
8.50 x 12.75 x 17.50 (215.9 x 323.9 x 444.5)
46 (21)
T800R-01000
8.50 x 12.75 x 17.50 (215.9 x 323.9 x 444.5)
62 (28)
T800R-01600
8.50 x 12.75 x 17.50 (215.9 x 323.9 x 444.5)
65 (29)
T800R-02100
8.50 x 12.75 x 17.50 (215.9 x 323.9 x 444.5)
68 (31)
T800R-02500
8.50 x 12.75 x 17.50 (215.9 x 323.9 x 444.5)
72 (33)
T800R-03500
8.50 x 12.75 x 17.50 (215.9 x 323.9 x 444.5)
73 (33)
T800R-03501
15.00 x 23.75 x 22.50 (381.0 x 603.3 x 571.5)
176 (80)
T800R-05000
15.00 x 23.75 x 22.50 (381.0 x 603.3 x 571.5)
210 (95)
T800R-07500
15.00 x 23.75 x 22.50 (381.0 x 603.3 x 571.5)
256 (116)
T800R-10000
15.00 x 23.75 x 22.50 (381.0 x 603.3 x 571.5)
314 (142)
T800R-15000
2
2
Office Models (with Receptacles)
Industrial Models (Hardwired Wall-/Panel-Mount)
2
2
2
2
2
2
2
9.00 x 14.00 x 10.00 (228.6 x 355.6 x 254.0)
52 (24)
T800P-00500
9.00 x 14.00 x 10.00 (228.6 x 355.6 x 254.0)
60 (27)
T800P-00750
9.00 x 14.00 x 10.00 (228.6 x 355.6 x 254.0)
82 (37)
T800P-01000
13.00 x 16.50 x 14.75 (330.2 x 419.1 x 374.7)
106 (48)
T800P-01500
13.00 x 16.50 x 14.75 (330.2 x 419.1 x 374.7)
125 (57)
T800P-02000
13.00 x 16.50 x 14.75 (330.2 x 419.1 x 374.7)
157 (71)
T800P-03000
27.00 x 22.50 x 28.50 (685.8 x 571.5 x 723.9)
437 (198)
T800P-05000
27.00 x 22.50 x 28.50 (685.8 x 571.5 x 723.9)
495 (225)
T800P-08000
27.00 x 22.50 x 28.50 (685.8 x 571.5 x 723.9)
537 (244)
T800P-10000
2
2
Industrial Models (Hardwired Floor-Mount)

23.00 x 20.00 x 28.50 (584.2 x 508.0 x 723.9)
407 (185)
T800F-05000
23.00 x 20.00 x 28.50 (584.2 x 508.0 x 723.9)
465 (211)
T800F-08000
23.00 x 20.00 x 28.50 (584.2 x 508.0 x 723.9)
507 (230)
T800F-10000
35.00 x 25.00 x 39.50 (889.0 x 635.0 x 1003.3)
830 (376)
T800F-15000
35.00 x 25.00 x 39.50 (889.0 x 635.0 x 1003.3)
950 (431)
T800F-20000
35.00 x 25.00 x 39.50 (889.0 x 635.0 x 1003.3)
1070 (485)
T800F-25000
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-45
2.1
2

Contents
Eaton Power-Suppress 100
Description
2
2
2
2
2
2
2
2
Ultra-Isolator Noise Suppressor and Isolation Provider
2
2
Introduction
SPC Surge Protective Device . . . . . . . . . . . . . . . . . .
CVX050/100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Sure 800. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-Suppress 100
Standards and Certifications . . . . . . . . . . . . . . . .
2
2
2
Power-Suppress 100
Product Description
Features
Eatons Power-Suppress
100 ultra-isolator noise
suppressors protect sensitive
equipment from electrical
noise disturbances. Using
exclusive double shielding
techniques, the PowerSuppress 100 blocks all forms
of electrical noise including
radio frequency interface
(RFI)/ electromagnetic
interference (EMI), over a
broad range of frequencies.
Furthermore, the noise
suppression is achieved
without impeding normal
power flow.
Applications for the PowerSuppress 100 include audio

and video equipment,
computer and process
equipment, telecommunications
systems, and virtually any
sensitive electronic
instruments.
2
2
2
2
2
2
2
2
2
2
2
Power-Suppress 100 ultraisolator noise suppressors can

reduce a 6000-volt spike to an
insignificant 0.0030 volt.
These high-voltage transients
contain enough energy to
completely destroy the
electrical circuit components
that are vital to daily
operation.
Traps unwanted harmonics

Removes surge voltages
and minimizes reflected
THD
Cleans and conditions the
sine wave
Eliminates load-generated
feedback
Available in both hardwired
or line cord/receptacle
models
Fast and easy installation
Long-life operation
Small footprintsaves
valuable space
Two-year warranty
complete unit, five-year
warranty core and coil
2
2
2
2
V3-T2-46
Page
V3-T2-5
V3-T2-7
V3-T2-11
V3-T2-16
V3-T2-20
V3-T2-24
V3-T2-27
V3-T2-29
V3-T2-31
V3-T2-36
V3-T2-40
V3-T2-42
V3-T2-47
V3-T2-47
V3-T2-47
V3-T2-48
V3-T2-48

2.1
UL 1012, UL 1449, cUL

listed, ANSI/IEEE
C57.12.91
Meets FCC Category A,
IEEE C62.41 Category A3
2
2
2
2
Power-Suppress 100
2
T100
Connection Method
R = Receptacles
H = Hardwired
0500
0750
1000
1800
2400
2500
5000
5001
7500
7501
Option/Frequency
Blank = 60 Hz
5
= 50 Hz
Size (VA)
= 500 VA
= 750 VA
= 1000 VA
= 1800 VA
= 2400 VA
= 2500 VA
= 5000 VA
= 5000 VA 1
= 7500 VA
= 7500 VA 1
2
2
2
2
2
2
Product Selection
2
Power-Suppress 100 Models
Input Voltages 2
Output Voltages 2
Output VA 3
I/O Interfaces (NEMA)
Catalog Number
2
2
Line-Cord/Receptacle Models
120
120
500
5-15P/(1) 5-20R2
T100R-0500
120
120
750
5-15P/(1) 5-20R2
T100R-0750
120
120
1000
5-15P/(1) 5-20R2
T100R-1000
120
120
1800
L5-20P/(2) 5-20R2
T100R-1800
120
120
2400
L5-30P/(2) 5-20R2
T100R-2400
120/240
120/240
500
Hardwired
T100H-0500
120/240
120/240
750
Hardwired
T100H-0750
120/240
120/240
1000
Hardwired
T100H-1000
120/240
120/240
1800
Hardwired
T100H-1800
120/240
120/240
2500
Hardwired
T100H-2500
120/240
120/240
5000
Hardwired
T100H-5000
240/480
120/240
5000
Hardwired
T100H-5001 1
120/240
120/240
7500
Hardwired
T100H-7500
240/480
120/240
7500
Hardwired
T100H-7501 1
2
2
Terminal Style Models
2
2
2
2
2
Notes
1 Models T100H-5001 and T100H-7501 will ship configured to 240 V input and output voltage.
2 Input and output voltages can be field configured for either 120 Vac or 240 Vac, 240 Vac or 480 Vac, as indicated above.
3 500 VA to 7500 VA hardwired models will ship configured to 120 V input and output voltage.
2
2
2
V3-T2-47
2.1
2
2

Dimensions
Technical Specifications
Description
Specifications
Power-Suppress 100 Models
Input voltage/frequency
120, 240, 480 V 1/60 Hz
Dimensions, W x D x H
Common-mode noise
140 dB at100 kHz
Line-Cord/Receptacle Models
Normal-mode noise
65 dB at100 kHz
Overload capacity
600% for 1 cycle, 300% for 30 seconds
Dielectric strength
Weight, Lb (kg)
Catalog Number
6.49 x 6.10 x 12.00 (164.8 x 154.9 x 304.8)
22 (10)
T100R-0500
6.49 x 6.10 x 12.00 (164.8 x 154.9 x 304.8)
28 (13)
T100R-0750
2,500 Vac minimum
6.49 x 6.10 x 12.00 (164.8 x 154.9 x 304.8)
31 (14)
T100R-1000
Frequency
60 Hz 5%
10.49 x 11.10 x 17.00 (266.4 x 281.9 x 431.8)
54 (24)
T100R-1800
Impedance
36% typical
10.49 x 11.10 x 17.00 (266.4 x 281.9 x 431.8)
58 (26)
T100R-2400
Efficiency
9397% typical
Terminal Style Models
Input voltage range
10% of nominal rated voltage
6.42 x 6.10 x 12.00 (163.1 x 154.9 x 304.8)
22 (10)
T100H-0500
Harmonic distortion
Adds less than 1% THD, under

linear loading
6.42 x 6.10 x 12.00 (163.1 x 154.9 x 304.8)
28 (13)
T100H-0750
6.42 x 6.10 x 12.00 (163.1 x 154.9 x 304.8)
31 (14)
T100H-1000
10.28 x 11.10 x 17.00 (261.1 x 281.9 x 431.8)
54 (24)
T100H-1800
10.28 x 11.10 x 17.00 (261.1 x 281.9 x 431.8)
58 (26)
T100H-2500
10.28 x 11.10 x 17.00 (261.1 x 281.9 x 431.8)
86 (39)
T100H-5000
10.49 x 11.10 x 17.00 (266.4 x 281.9 x 431.8)
92 (42)
T100H-5001
Coil insulation
200 C
Temperature rise
115 C max rise above a 40 C ambient, depending on

model
Electromagnetic interference
Environments
10.28 x 11.10 x 17.00 (261.1 x 281.9 x 431.8)
116 (53)
T100H-7500
Description
Specifications
10.28 x 11.10 x 17.00 (261.1 x 281.9 x 431.8)
111 (50)
T100H-7501
Audible noise
Less than 50 dBA measured at 3 ft from

the noise suppressor
0 to 40 C
Storage temperature
20 to 50 C
2
2
2
<0.2 gauss at 36 inches
Operating altitude
Up to 12,000 ft (3657.6 m) (without derating)
Operating humidity
95% relative (noncondensing)
Line-Cord Style
5-15P Input
Line Cord
8.00 (203.2)
Input Plug
6.49
(164.8)
Output Receptacle
5001000 VA
5-15P
5-20R duplex
1.8 kVA
L5-20P
2 x 5-20R duplex
2.4 kVA
L5-30P
2 x 5-20R duplex
1.87.5 kVA Front View
10.28
(261.1)
Plug and Receptacle Configuration Models

Rating
Terminal Style
Input
Fuse
6.10
(154.9)
5-20R2
Output
Receptacles
500 VA1 kVA
11.10
(281.9)
5001000 VA Rear View
L5-20 Input
Line Cord
8.00 (203.2)
2
2
Input Fuse
10.49
(266.4)
1.87.5 kVA Rear View
2
2
Input Fuse
5-20R2 Output
Receptacles
1.82.4 kVA
0.50 (12.7)
Input/Output
Conduit Knockouts
2
2
Note
1 480 V available for 5 and 7.5 kVA models only.
2
2
V3-T2-48

2.2
Contents
Capacitor Cell with Cage Clamp Terminals
Description
Page
Product Overview
Product Selection . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitor Systems . . . . . . . . . . . . . . . . . . . . . . .
AUTOVAR 600 Automatic Power Factor
Correction Capacitor Systems . . . . . . . . . . . . . .
AUTOVAR FilterLV Automatic Detuned Filter . . .
Transient-Free Static Switching Power Factor
Correction Units . . . . . . . . . . . . . . . . . . . . . . . . .
HCU2 Harmonic Correction Unit . . . . . . . . . . . . . .
V3-T2-50
V3-T2-50
V3-T2-51
V3-T2-54
2
2
2
2
V3-T2-63
V3-T2-67
V3-T2-74
V3-T2-81
V3-T2-83
2
2
2
2
2
Product Overview
Product Description
Eatons power factor
correction capacitors and
harmonic filters are an
essential part of modern
electric power systems.
capacitors are the simplest
and most economical
means of increasing the
capacity of any power
system, minimizing energy
losses and correcting load
power factor. In addition,
power factor penalties can
be reduced and power quality
can be greatly enhanced.
There are several reasons

to correct poor power factor.
The first is to reduce or
eliminate a power factor
penalty charged by the utility.
Another reason is that your
existing transformer is, or
shortly will be, at full capacity
and installing power factor
correction capacitors can
be a very cost-effective
solution to installing a brand
new service. Depending on
the amount of power factor
correction (kvar that needs to
be injected into the electrical
system to improve the power
factor) and the dynamic
nature of the load,
a fixed or switched capacitor
bank may be the best
solution.
When capacity becomes a

problem, the choice of a
solution will be dependent
upon the size of the increase
needed. Like all power
quality solutions, there
are many factors that need
to be considered when
determining which solution
will be best to solve your
power factor problem.
Harmonic Filtering
As the world becomes more
dependent on electric and
electronic equipment, the
likelihood that the negative
impact of harmonic distortion
increases dramatically. The
efficiency and productivity
gains from these increasingly
sophisticated pieces of
equipment have a negative
side effectincreased
harmonic distortion in the
power lines. The difficult
thing about harmonic
distortion is determining the
cause. Once this has been
determined, the solution
can be easy. Active harmonic
filtering equipment will
mitigate specific harmonic
issues, and correct poor
power factor as well.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-49
2.2

Product Selection
Capacitor Cell Chart
2
2
2
2
2
2
Heavy-Duty Capacitor Cell Chart


Voltage
kvar 1
Weight in
Lb (kg)
Catalog
Number
240
1.5
3.1 (79.5)
7.9 (200.0)
1.1 (0.5)
643PCRMB
240
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
8B43PCRMB
240
240
240
240
240
2.5
3
4
5
6.3
3.1 (79.5)
3.5 (89.5)
3.1 (79.5)
3.5 (89.5)
3.1 (79.5)
9.4 (238.0)
9.4 (238.0)
7.9 (200.0)
12.3 (313.0)
9.4 (238.0)
1.3 (0.6)
1.8 (0.8)
1.1 (0.5)
2.6 (1.2)
1.3 (0.6)
1043PCRMB
12X43PCRMB
423PCRMB
2043PCRMB
6B23PCRMB
Nameplate
Voltage
kvar
240
12.5
3.5 (89.5)
480
15.0
3.5 (89.5)
480
16.7
480
Internal
Voltage
Rating
Weight in
Lb (kg)
Catalog
Number
15.3 (388.0) 360
3.3 (1.5)
12X23PHRMB
12.3 (313.0) 525
2.6 (1.2)
1543PHRMB
3.5 (89.5)
15.3 (388.0) 600
3.3 (1.5)
16S43PHRMBS
20.0
3.5 (89.5)
15.3 (388.0) 525
3.3 (1.5)
2043PHRMB
480
25.0
3.5 (89.5)
15.3 (388.0) 525
3.3 (1.5)
2543PHRMB
600
12.3
3.5 (89.5)
12.3 (313.0) 660
2.6 (1.2)
12A63PHRMB
600
14.7
3.5 (89.5)
15.3 (388.0) 660
3.3 (1.5)
14S63PHRMB
600
16.7
3.5 (89.5)
15.3 (388.0) 660
3.3 (1.5)
16S63PHRMB
240
7.5
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
7X23PCRMB
240
8.3
3.5 (89.5)
9.4 (238.0)
3.3 (1.5)
8B23PCRMB
240
10
3.5 (89.5)
9.4 (238.0)
2.0 (0.9)
1023PCRMB
240
12.5
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
12X23PCRMB
Dimensions
240
15
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
1523PCRMB
480
1.5
2.1 (53.0)
5.0 (125.8)
0.7 (0.3)
1X43PCRMA
480
2.5 (63.5)
5.5 (140.8)
0.9 (0.4)
243PCRMA
480
2.5
2.5 (63.5)
5.5 (140.8)
0.9 (0.4)
2X43PCRMA
480
2.5 (63.5)
5.5 (140.8)
0.9 (0.4)
343PCRMA
480
2.5 (63.5)
6.5 (165.8)
0.9 (0.4)
443PCRMA
480
2.5 (63.5)
6.5 (165.8)
0.9 (0.4)
543PCRMA
480
3.1 (79.5)
7.9 (200.0)
1.1 (0.5)
643PCRMB
480
7.5
3.1 (79.5)
7.9 (200.0)
1.1 (0.5)
7X43PCRMB
480
8.3
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
8B43PCRMB
480
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
943PCRMB
480
10
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
1043PCRMB
480
12.5
3.5 (89.5)
9.4 (238.0)
1.8 (0.8)
12X43PCRMB
480
15
3.5 (89.5)
9.4 (238.0)
1.8 (0.8)
1543PCRMB
480
18
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
1843PCRMB
480
20
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
2043PCRMB
480
25
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
2543PCRMB
600
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
563PCRMB
600
7.5
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
7X63PCRMB
600
10
3.1 (79.5)
9.4 (238.0)
1.3 (0.6)
1063PCRMB
600
12.5
3.5 (89.5)
9.4 (238.0)
1.8 (0.8)
12X63PCRMB
600
15
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
1563PCRMB
600
17.5
3.5 (89.5)
12.3 (313.0)
2.6 (1.2)
17X63PCRMB
600
20
3.5 (89.5)
12.3 (313.0)
3.3 (1.5)
2063PCRMB
600
25
3.5 (89.5)
15.3 (388.0)
3.3 (1.5)
2563PCRMB
Capacitor Cell
Note
1 kvar rating standard. Standard kvar tolerance is 0% to +5%.
Part number shown is for three-phase units. Up to 5 kvar at 480 V
quick disconnect terminals are standard. Above 5 kvar at 480 V (and on
all other voltages)cage clamp terminals are standard.
2
2
2
2
2
2
V3-T2-50

2.2
Contents
UNIPUMP
Description
Page
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPUMP
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-49
V3-T2-52
V3-T2-53
V3-T2-54
2
2
2
2
V3-T2-63
V3-T2-67
V3-T2-74
V3-T2-81
V3-T2-83
2
2
2
2
2
UNIPUMP
Product Description
Non-fused capacitors for
outdoor irrigation and oil field
installations.
Designed expressly for

outdoor pumping
applications
Pole or wall mounting
Small, light-weight
enclosure for easy
installation
SO-WA type flexible cable
facilitates installation
(4-conductor)
Gland-type weatherproof
bushings
Strong outer case
Outdoor irrigation and oil
and gas field pumping.

Configuration
Outer case: Heavy, No. 14

gauge steel finished with
durable powder coat finish.
Integral strap mounting
bracket with keyhole at top
for pole or wall installation.
No knockouts
Capacitor Cells
Terminals: Insulated
finger-safe terminals rated
for 3 kVAC withstand
Dielectric fill: Dry-type

cells use soft organic
polymer resinResinol
Eliminates potential for

corona/partial discharge/
electrochemical oxidation
Excellent heat dissipation
Flash point: +444 F

(+229 C)
Fire point: +840 F

(+449 C)
Design: Self-healing
metallized high crystalline
polypropylene with ramp
metallization film. Total
losses less than 0.45 watt
per kvar. (Dielectric losses
less than 0.2 watt per kvar)
Ramp metallization:
Provides thicker film at
higher current density
areas, allowing for reduced
internal losses, lower
operating temperatures
and longer life expectancy.
Also prevents chain
reaction breakdown by
limiting propagation of
film vaporization
Pressure sensitive
interrupter: Built-in, threephase pop-up interrupter
design. UL recognized.
Removes capacitor from
line before internal
pressure can cause case
rupture. Bulged capacitor
cell top provides easy
visual indication of
interrupter operation
Ceramic discharge
resistors: Reduce residual
voltage to less than 50 volts
within one minute of
de-energization. Selected
for 20-year nominal life.
Exceeds NEC requirements
Capacitor operating
temperature: -40 F
(40 C) to +115 F
(+46 C)
Case: Weatherproof
aluminum housing
Warranty: The longest
in the industryfive full
years of warranty on
capacitor cells
UL 810 and C22.2 No. 190

listed
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-51
2.2
2
2

Product Selection
UNIPUMP
UNIPUMP
Rated
Current
Case
Size
Cable
Size
Shipping Weight
in Lb (kg)
Catalog
Number
4.8
AA
14
10.0 (4.5)
223JMR
2.5
6.0
AA
14
10.0 (4.5)
2X23JMR
7.2
AA
14
10.0 (4.5)
323JMR
9.6
AA
14
11.0 (5.0)
423JMR
12.0
BB
12
11.0 (5.0)
523JMR
14.4
BB
12
15.0 (6.8)
623JMR
7.5
18.0
BB
12
15.0 (6.8)
7X23JMR
2.4
AA
14
10.4 (4.7)
243JMR
2.5
3.0
AA
14
10.4 (4.7)
2X43JMR
3.6
AA
14
10.4 (4.7)
343JMR
4.8
AA
14
10.4 (4.7)
443JMR
6.0
AA
14
10.4 (4.7)
543JMR
7.2
AA
14
10.6 (4.8)
643JMR
7.5
9.0
AA
14
10.6 (4.8)
7X43JMR
10
12.0
AA
14
10.8 (4.9)
1043JMR
12.5
15.0
BB
12
15.0 (6.8)
12X43JMR
15
18.0
BB
12
15.0 (6.8)
1543JMR
17.5
21.0
BB
15.8 (7.2)
17X43JMR
20
24.0
BB
16.8 (7.6)
2043JMR
25
30.0
BB
16.8 (7.6)
2543JMR
4.9
AA
14
10.8 (4.9)
563JMR
7.5
7.4
AA
14
10.8 (4.9)
7X63JMR
10
9.8
AA
14
10.8 (4.9)
1063JMR
12.5
12.3
BB
12
15.0 (6.8)
12X63JMR
15
14.7
BB
12
15.8 (7.2)
1563JMR
17.5
17.2
BB
16.8 (7.6)
17X63JMR
20
19.6
BB
16.8 (7.6)
2063JMR
kvar
240 Vac
480 Vac
600 Vac
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-52
2.2

Dimensions

UNIPUMP
UNIPUMP Dimension Chart

0.44
(11.2)
0.88
(22.4)
1.84
(46.7)
Size Code
AA
11.00 (279.4)
14.20 (360.7)
12.60 (320.0)
13.20 (335.3)
BB
14.00 (355.6)
17.10 (434.3)
15.50 (393.7)
16.10 (408.9)
2
2
2
1.75
(44.5)
2
2
2
2
2
2
1.45
(36.8)
0.75
0.50
(12.7) (19.1)
0.44
(11.2)
1.50
(38.1)
5.15
(130.8)
1.55
(39.4)
2
2
0.07
(1.8)
2.56
(65.0)
1.98
(50.3)
2
2
2
2
2
5.00
(127.0)
1.75
(44.5)
2
2
2
2
2
2
V3-T2-53
2.2
2

Contents
UNIPAK
Description
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK
Features, Benefits and Functions . . . . . . . . . .
Standards and Certifications . . . . . . . . . . . . . .
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . .
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOVAR FilterLV Automatic Detuned Filter. . .
HCU2 Harmonic Correction Unit. . . . . . . . . . . . . .
2
2
2
2
2
2
2
2
2
UNIPAK
Product Description
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
UNIPAK Low Voltage Fixed

Capacitor Banks
Two-year warranty on
capacitor cells (units with
standard-duty cells)
Five-year warranty on
capacitor cells (units with
heavy-duty cells)
Indoor/outdoor service
Wall-mount (up to C2) and

floor-mounted units
available
Short lead-times
Slim profile allows reduced

footprint, conserving
valuable floor space
Detuned Filters
Detuned filter systems for

low voltage, heavy-duty
applications
Correct power factor in

high harmonic
environments
Two-enclosure design
isolates capacitors from
high-temperature operating
reactors and allows for
flexible installation
Five-year cell warranty/

one-year reactor warranty
Three-phase cell capacitor

construction
Designed for power factor

correction in plants
experiencing harmonics
problems due to high
amounts of nonlinear loads.
UNIPAK with Heavy-Duty

Capacitor Cells
Standard fixed capacitor

systems using heavy-duty
capacitor cells
For use in moderate

harmonic environments
where engineering
evaluation allows in place
of detuned filter designs
Provides future conversion

capability into a detuned
filter system when required
by facility growth or
increased nonlinear
load levels
2
2
V3-T2-54
Page
V3-T2-49
V3-T2-51
V3-T2-55
V3-T2-55
V3-T2-56
V3-T2-60
V3-T2-61
V3-T2-63
V3-T2-67
V3-T2-74
V3-T2-81
V3-T2-83


Capacitor Banks
Outer enclosure: Heavy,

No. 14 gauge steel finished
with durable baked powder
coat finish. Wall-mounting
flanges and floor-mounting
feet. Elimination of
knockouts permits indoor/
outdoor use. Manufactured
to NEMA 1 and 3R
requirements
Elevated floor-mounting
feet allow access for easy
maintenance
Cover: L shaped
gasketed cover with
multiple fasteners provides
front opening for ease of
installation and service
UNIPAK operating
temperature: 40 F to
+115 F (40 C to +46 C)
UNIPAK storage
temperature: 40 F to
+131 F (40 C to +55 C)
Power and ground

terminal lugs: Furnished
inside enclosure
Pressure-sensitive
interrupter: All units have
built-in UL recognized
pressure-sensitive
interrupter, and thermally
or mechanically activated
disconnecting link removes
capacitor from the supply
before dangerous pressure
buildup or excessive fault
current occurs. Bulged
capacitor cell top provides
easy visual indication of
interrupter operation
Standard fusing:
Size Code A1: Three

midget-type fuses with
100,000 A interrupting
capacity
Size Code A2 and

larger: Slotted-blade
type fuses with 200,000
A interrupting capacity;
fuses mounted on
stand-off bushings;
solderless connectors
for easy hookup of
incoming line
conductors
Fuse indicating lights:

Red, neon cleared-fuse
indicating lights are
protected by transparent
weatherproof guard
2.2

Capacitor Banks
UL 810 and CSA C.22.2

No.190 Listed

Detuned Filters
UL 508A and CSA C22.2

No. 190 Listed
2
2
2
2
2
2
2
2
Options:
Non-fused units
available, selected sizes
Heavy-duty capacitor
cells, selected sizes
2
2
2

Detuned Filters
Enclosures: Standard
NEMA 1 enclosures have
durable baked powder coat
finish
UNIPAK detuned filter

operating temperature:
40 F to +115 F
(40 C to +46 C)
UNIPAK detuned filter

storage temperature:
40 F to +131 F
(40 C to +55 C)
Power and ground

terminal lugs: Furnished
inside enclosures
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-55
2.2

Product Selection
UNIPAK Low Voltage Fixed Capacitor Banks
UNIPAK
240 Vac UNIPAK Selection Chart
kvar
Rated
Current
(Amperes)
Enclosure
Shipping
Weight in
Lb (kg)
Catalog
Number
2.4
A1
18 (8)
123PMURF
1.5
3.6
A1
18 (8)
1X23PMURF
4.8
A1
19 (9)
223PMURF
2.5
A1
19 (9)
2X23PMURF
7.2
A1
19 (9)
323PMURF
9.6
A1
20 (9)
423PMURF
12
A2
29 (13)
523PMURF
14.4
A2
29 (13)
623PMURF
7.5
18
A2
30 (14)
7X23PMURF
19.2
A2
31 (14)
823PMURF
10
24
A2
31 (14)
1023PMURF
12.5
30
A2
32 (14)
12X23PMURF
15
36
A2
33 (15)
1523PMURF
17.5
42
B1
44 (20)
17X23PMURF
20
48
B1
45 (20)
2023PMURF
22.5
54
B1
46 (21)
22X23PMURF
25
60
B1
46 (21)
2523PMURF
30
72
B1
47 (21)
3023PMURF
32.5
78
C1
47 (22)
32X23PMURF
35
84
C1
48 (22)
3523PMURF
37.5
90
C1
60 (27)
37X23PMURF
40
96
C1
64 (29)
4023PMURF
42.5
102
C1
65 (30)
42X23PMURF
45
108
C1
66 (30)
4523PMURF
50
120
C1
68 (31)
5023PMURF
60
144
C1
69 (31)
6023PMURF
70
168
C2
99 (45)
7023PMURF
75
180
C2
100 (46)
7523PMURF
80
192
C2
101 (46)
8023PMURF
90
216
C2
103 (47)
9023PMURF
100
240
D1
104 (47)
10023PMURF
120
288
D1
133 (60)
12023PMURF
140
336
E1
137 (62)
14023PMURF
150
360
E1
140 (64)
15023PMURF
160
384
E1
175 (80)
16023PMURF
180
432
E1
182 (83)
18023PMURF
200
480
E1
189 (86)
20023PMURF
Notes
Multiply the 240 Vac kvar rating by 0.75 to calculate the kvar value at 208 Vac.
Fused with blown-fuse indication available standard. Non-fused and no lights also availableplease consult the factory.
Other ratings available, consult factory.
For dimensional information, refer to Page V3-T2-61.
Part Numbers:
PMURFthree fuses + three lights
PMURNnon-fused
2
2
2
2
V3-T2-56

kvar
Rated
Current
(Amperes)
1X43PMURF
18 (8)
243PMURF
7.5
A1
18 (8)
2X43PMURF
10
9.8
A1
19 (9)
343PMURF
12.5
12.3
4.8
A1
19 (9)
443PMURF
15
14.7
A1
19 (9)
543PMURF
17.5
17.2
kvar
Rated
Current
(Amperes)
1.5
2.2
Enclosure
Shipping
Weight in
Lb (kg)
Catalog
Number
1.8
A1
17 (8)
2.4
A1
2.5
3.6
4
5
Enclosure
Shipping
Weight in
Lb (kg)
Catalog
Number
4.9
A1
19 (9)
563PMURF
7.4
A1
19 (9)
7X63PMURF
A1
20 (9)
1063PMURF
A1
20 (9)
12X63PMURF
A2
29 (13)
1563PMURF
A2
29 (13)
17X63PMURF
7.2
A1
19 (9)
643PMURF
20
19.6
A2
30 (14)
2063PMURF
7.5
A1
20 (9)
7X43PMURF
22.5
22.1
B1
44 (20)
22X63PMURF
9.6
A1
20 (9)
843PMURF
25
24.5
B1
31 (14)
2563PMURF
10.8
A1
20 (9)
943PMURF
27.5
27.0
B1
44 (20)
27X63PMURF
10
12
A1
20 (9)
1043PMURF
30
29.4
B1
45 (20)
3063PMURF
12.5
15
A2
29 (13)
12X43PMURF
32.5
31.9
B1
45 (20)
32X63PMURF
15
18
A2
29 (13)
1543PMURF
35
34.3
B1
46 (21)
3563PMURF
17.5
21
A2
30 (14)
17X43PMURF
37.5
36.8
B1
46 (21)
37X63PMURF
20
24
A2
31 (14)
2043PMURF
40
39.2
B1
47 (21)
4063PMURF
22.5
27
B1
44 (20)
22X43PMURF
42.5
41.7
B1
47 (22)
42X63PMURF
25
30
A2
32 (15)
2543PMURF
45
44.1
B1
48 (22)
4563PMURF
27.5
33
B1
44 (20)
27X43PMURF
50
49.0
B1
48 (22)
5063PMURF
30
36
B1
44 (20)
3043PMURF
55
53.9
C1
64 (29)
5563PMURF
32.5
39
B1
45 (20)
32X43PMURF
60
58.8
C1
64 (29)
6063PMURF
35
42
B1
45 (20)
3543PMURF
65
63.7
C1
65 (30)
6563PMURF
37.5
45
B1
46 (21)
37X43PMURF
70
68.6
C1
65 (30)
7063PMURF
40
48
B1
46 (21)
4043PMURF
75
73.5
C1
66 (30)
7563PMURF
42.5
51
B1
47 (21)
42X43PMURF
80
78.4
C1
68 (31)
8063PMURF
45
54
B1
47 (22)
4543PMURF
85
83.3
C1
68 (31)
8563PMURF
50
60
B1
48 (22)
5043PMURF
90
88.2
C1
69 (31)
9063PMURF
55
66
C1
48 (22)
5543PMURF
100
98.0
C1
69 (31)
10063PMURF
60
72
C1
48 (22)
6043PMURF
120
117.6
C2
99 (45)
12063PMURF
65
78
C1
64 (29)
6543PMURF
125
122.5
C2
100 (46)
12563PMURF
70
84
C1
65 (30)
7043PMURF
140
137.2
C2
101 (46)
14063PMURF
75
90
C1
65 (30)
7543PMURF
150
147.0
C2
103 (47)
15063PMURF
80
96
C1
66 (30)
8043PMURF
160
156.8
D1
135 (61)
16063PMURF
85
102
C1
68 (31)
8543PMURF
180
176.4
D1
137 (62)
18063PMURF
90
108
C1
68 (31)
9043PMURF
200
196.0
D1
140 (64)
20063PMURF
100
120
C1
69 (31)
10043PMURF
225
220.5
D1
143 (65)
22563PMURF
120
144
C2
69 (31)
12043PMURF
250
245.0
E1
170 (77)
25063PMURF
125
150
C2
99 (45)
12543PMURF
300
294.0
E1
175 (80)
30063PMURF
140
168
C2
100 (46)
14043PMURF
350
343.0
E1
182 (83)
35063PMURF
150
180
C2
101 (46)
15043PMURF
400
392.0
E1
189 (86)
40063PMURF
160
192
D1
103 (47)
16043PMURF
Notes
Fused with blown-fuse indication available standard.
Non-fused and no lights also availableplease consult the factory.
For dimensional information, refer to Page V3-T2-61.
Part Number
PMURFthree fuses + three lights
PMURNnon-fused
180
216
D1
104 (47)
18043PMURF
200
240
D1
137 (62)
20043PMURF
225
270
D1
140 (64)
22543PMURF
250
300
E1
170 (77)
25043PMURF
300
360
E1
175 (80)
30043PMURF
350
420
E1
182 (83)
35043PMURF
400
480
E1
189 (86)
40043PMURF
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-57
2.2
2
2

UNIPAKwith Harmonic Cells
Harmonic Cells
Low Voltage Fixed Capacitor Systems with Heavy-Duty Cells
kvar
Rated
Current
(Amperes)
Case
Size
Shipping
Weight in
Lb (kg)
Catalog
Number
240 V
15
36
B1
38.4 (17)
1523HURF
25
60
B1
38.4 (17)
2523HURF
30
72
C1
55.2 (25)
3023HURF
50
120
C1
57.6 (26)
5023HURF
60
144
C2
100.8 (46)
6023HURF
75
180
C2
104.4 (47)
7523HURF
100
240
D1
136.8 (62)
10023HURF
125
300
E1
189.6 (86)
12523HURF
15
18
B1
25.2 (11)
1543HURF
25
30
B1
37.2 (17)
2543HURF
30
36
B1
38.4 (17)
3043HURF
50
60
C1
39.6 (18)
5043HURF
60
72
C1
52.8 (24)
6043HURF
75
90
C2
55.2 (25)
7543HURF
100
120
C2
57.6 (26)
10043HURF
125
150
D1
100.8 (46)
12543HURF
150
180
D1
104.4 (47)
15043HURF
200
240
E1
136.8 (62)
20043HURF
250
300
E1
186.0 (84)
25043HURF
15
14.7
B1
37.2 (17)
1563HURF
25
24.5
B1
38.4 (17)
2563HURF
30
29.4
B1
39.6 (18)
3063HURF
50
49
C1
55.2 (25)
5063HURF
60
58.8
C1
57.6 (26)
6063HURF
75
73.5
C2
100.8 (46)
7563HURF
100
98
C2
104.4 (47)
10063HURF
125
122.5
D1
136.8 (62)
12563HURF
150
147
D1
136.8 (62)
15063HURF
200
196
E1
186.0 (84)
20063HURF
250
245
E1
189.6 (86)
25063HURF
480 V
600 V
Notes
Fused with blown-fuse indication standard.
2
2
2
2
2
2
2
V3-T2-58

2.2
UNIPAK Low Voltage Fixed Detuned Filters
2
2
Fixed UNIPAK Detuned Filters

Rated
Current
(Amperes)
Capacitor
Enclosure
Size
Shipping
Weight
in Lb (kg)
Reactor
Enclosure
Case Size
Reactor
Shipping Weight
in Lb (kg)
Combined
Shipping Weight
in Lb (kg)
Catalog
Number
15
36
B1
48.4 (22.0)
90.0 (40.9)
138.4 (62.8)
15232HMURFY
25
60
B1
48.4 (22.0)
105.0 (47.7)
153.4 (69.6)
25232HMURFY
30
72
C1
65.2 (29.6)
110.0 (49.9)
175.2 (79.5)
30232HMURFY
50
120
C1
67.6 (30.7)
130.0 (59.0)
197.6 (89.7)
50232HMURFY
60
144
C2
110.8 (50.3)
160.0 (72.6)
270.8 (122.9)
60232HMURFY
75
180
C2
114.4 (51.9)
185.0 (84.0)
299.4 (135.9)
75232HMURFY
100
240
D1
146.8 (66.6)
240.0 (109.0)
386.8 (175.6)
100232HMURFY
125
300
E1
199.6 (90.6)
280.0 (127.1)
479.6 (217.7)
125232HMURFY
150
360
E1
220.0 (99.9)
280.0 (127.1)
500.0 (227.0)
150232HMURFY
15
18
B1
35.2 (16.0)
90.0 (40.9)
125.2 (56.8)
15432HMURFY
25
30
B1
47.2 (21.4)
105.0 (47.7)
152.2 (69.1)
25432HMURFY
30
36
B1
48.4 (22.0)
110.0 (49.9)
158.4 (71.9)
30432HMURFY
50
60
C1
49.6 (22.5)
130.0 (59.0)
179.6 (81.5)
50432HMURFY
60
72
C1
62.8 (28.5)
160.0 (72.6)
222.8 (101.2)
60432HMURFY
75
90
C2
65.2 (29.6)
185.0 (84.0)
250.2 (113.6)
75432HMURFY
100
120
C2
67.6 (30.7)
240.0 (109.0)
307.6 (139.7)
100432HMURFY
125
150
D1
110.8 (50.3)
280.0 (127.1)
390.8 (177.4)
125432HMURFY
150
180
D1
114.4 (51.9)
280.0 (127.1)
394.4 (179.1)
150432HMURFY
200
240
E1
146.8 (66.6)
330.0 (149.8)
476.8 (216.5)
200432HMURFY
250
300
E1
196.0 (89.0)
570.0 (258.8)
766.0 (347.8)
250432HMURFY
14.7
B1
47.2 (21.4)
90.0 (40.9)
137.2 (62.3)
15632HMURFY
kvar
2
2
240 V
480 V
600 V
15
25
24.5
B1
48.4 (22.0)
90.0 (47.7)
153.4 (69.6)
25632HMURFY
30
29.4
B1
49.6 (22.5)
105.0 (49.9)
159.6 (72.5)
30632HMURFY
50
49
C1
65.2 (29.6)
110.0 (59.0)
195.2 (88.6)
50632HMURFY
60
58.8
C1
67.6 (30.7)
130.0 (72.6)
227.6 (103.3)
60632HMURFY
75
73.5
C2
110.8 (50.3)
160.0 (84.0)
295.8 (134.3)
75632HMURFY
100
98
C2
114.4 (51.9)
185.0 (109.0)
354.4 (160.9)
100632HMURFY
150
147
D1
146.8 (66.6)
280.0 (127.1)
426.8 (193.8)
150632HMURFY
200
196
E1
196.0 (89.0)
330.0 (149.8)
526.0 (238.8)
200632HMURFY
250
245
E1
199.6 (90.6)
570.0 (258.8)
769.6 (349.4)
250632HMURFY
Notes
Fused with blown-fuse indication standard.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-59
2.2
2
2

Wiring Diagram
Filter Schematic with Wiring Interconnects
Power Lines from Disconnect
2
2
Lugs
Fuses
2
Reactor Enclosure
2
2
Lugs
Lugs
Capacitor Enclosure
Interconnects (Provided by Customer)
2
2
Note
1 Refer to NEC.
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-60
2.2

Dimensions

Reactor Cabinet
Reactor Cabinet
Case Size
Height
Width
Depth
24.75 (628.7)
20.00 (508.0)
18.13 (460.5)
25.00 (635.0)
24.25 (616.0)
20.25 (514.4)
31.00 (787.4)
25.00 (635.0)
32.75 (831.9)
2
2
2
2
2
Low Voltage Fixed Capacitor Banks and Fixed Harmonic Filters

Case A1, A2
Case B1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
UNIPAK Enclosures
Case Size
X1
X2
X3
A1
5.30 (134.6)
8.50 (215.9)
3.50 (88.9)
3.80 (96.5)
10.60 (269.2)
17.30 (439.4)
6.80 (172.7)
2.00 (50.8)
N/A
N/A
7.70 (195.6)
7.20 (182.9)
A2
6.00 (152.4)
8.50 (215.9)
5.60 (142.2)
4.50 (114.3)
13.30 (337.8)
22.30 (566.4)
6.80 (172.7)
2.30 (58.4)
N/A
N/A
7.70 (195.6)
7.20 (182.9)
B1
11.10 (281.9)
10.10 (256.5)
5.80 (147.3)
9.60 (243.8)
15.70 (398.8)
25.30 (642.6)
8.50 (215.9)
4.10 (104.1)
4.50 (114.3)
N/A
9.30 (236.2)
8.80 (223.5)
Legend:
A = Total depth
B = Total width
D = Height of removable front cover
E = Depth of feet
F = Height of middle mounting hole in wall bracket
H = Total height
L = Width without feet and brackets
X = Depth between front and rear mounting holes in inches
Y = Width between floor mounting holes
Z = Width between wall bracket mounting holes
2
2
2
2
2
2
2
2
V3-T2-61
2.2
2
2


Case C1, C2
Case D1, E1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
UNIPAK Enclosures
Case
Size
X1
X2
X3
C1
10.60 (269.2)
12.10 (307.3)
7.10 (180.3)
9.10 (231.1)
16.20 (411.5)
26.30 (668.0)
10.40 (264.2)
3.40 (86.4)
1.10 (27.9)
3.60 (91.4)
11.30 (287.0)
10.70 (271.8)
C2
12.00 (304.8)
19.30 (490.2)
16.90 (429.3)
9.50 (241.3)
16.30 (414.0)
36.00 (914.4)
17.70 (449.6)
3.00 (76.2)
1.50 (38.1)
3.80 (96.5)
18.30 (464.8)
18.00 (457.2)
D1
16.80 (426.7)
19.30 (490.2)
16.90 (429.3)
14.60 (370.8)
N/A
36.00 (914.4)
17.70 (449.6)
5.10 (129.5)
2.40 (61.0)
5.00 (127.0)
18.30 (464.8)
N/A
E1
22.30 (566.4)
24.40 (619.8)
16.80 (426.7)
19.50 (495.3)
N/A
36.00 (914.4)
22.70 (576.6)
6.50 (165.1)
4.40 (111.8)
5.00 (127.0)
22.40 (569.0)
N/A
Legend:
A = Total depth
B = Total width
D = Height of removable front cover
E = Depth of feet
F = Height of middle mounting hole in wall bracket
H = Total height
L = Width without feet and brackets
X = Depth between front and rear mounting holes in inches
Y = Width between floor mounting holes
Z = Width between wall bracket mounting holes
2
2
2
2
2
V3-T2-62

2.2
Contents
AUTOVAR 300
Description
Page
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Capacitor Systems
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-49
V3-T2-51
V3-T2-54
V3-T2-65
V3-T2-64
V3-T2-66
V3-T2-67
V3-T2-74
V3-T2-81
V3-T2-83
2
2
2
2
2
2
2
2
2
2
Product Description
Automatically switched
power factor correction
systems for low voltage
applications.
Wallmount design is ideal

for minimum space
requirements
Programmable to
automatically add/subtract
capacitor stages to
maintain preset target
power factor
Heavy-duty, three-phase
capacitor construction
Five-year warranty of cells
against manufacturing
defects
AUTOVAR 300 is an ideal
capacitor bank to automatically
regulate power factor where
floor space is limited and
expansion of the facilitys
electrical load is not
expected.
Features
Configuration
Cabinet: Wallmounting 12
gauge steel with ANSI 61
gray, NEMA 1 (gasketed)
Power line interconnect:

Rugged, power distribution
block connection. Typical
power distribution block
can accommodate phase
wire sizes from 4 AWG to
500 kcmil; typical ground
lug can accommodate wire
sizes from 14 AWG to 2/0
AWG. Consult equipment
approval drawings for
actual lug size
Control wiring: UL type

MTW/AWM, CSA TEW 105 C
copper wire is standard
Fusing: 200,000 A
interrupting capacity
provided on all three
phases of each stage.
Blade-type fuses mounted
on insulator stand-offs with
cleared-fuse indicating
lights
Cleared-fuse lights:
Cleared-fuse neon
indicating lights for each
phase and stage located on
the door
Door interlock: Door

interlock automatically
disengages capacitors.
Power continues to be
provided to the unit until
the disconnect is open
Exhaust fan: Provides
ventilation; dust filtering
included
Safety: Ground fault
interruption provides
protection in case of
accidental contact with
control power and ground
Conduit/cable entry:
Available in top/side cable
entry
Thermal sensing: Built-in
thermal sensing, alarming,
and protection feature
allows the unit to operate
in optimal temperature
while alerting the user of
ambient temperature
exceeding the nominal
operating range. Stages
will be automatically
switched off if temperature
exceeds the maximum
specified temperature
Temperature range: The

operating temperature
range is 20C to +46C,
and the storage
temperature range is
40C to +55C. For
optimal equipment life,
the temperature should not
exceed 35C annual
average, and the
environment should not
exceed Pollution Degree 2
as defined in UL 61010-1
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-63
2.2

2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Controller
Visual indication of
incorrect CT polarity
Digital display of power

factor and number of
energized stages
Automatic setting of c/k

value (sensitivity based on
CT ratio and kvar available)
insufficient kvar to reach
target power factor
Automatic sensing of kvar

values per step
Optional communications
capable controller (RS-485/
Modbus)
Standard metering
capability:
Voltage
Current (sensed phase

only)
Frequency
Active power (kW)
Reactive power (kvar)
Apparent power (kVA)
Total voltage harmonic

distortion (VTHD)
Individual harmonic
voltage distortion (odd
orders up to the 19th
harmonic)
Built-in manual mode

allows for testing and
manual operation of stages
Multiple user-friendly alarm

displays. Controller
provides easy-to-understand
alarms for various
conditions, such as:
Undervoltage or
overvoltage
Undercurrent or
overcurrent
Target power factor

not met
Harmonic overload
Faulty step/stages
Overtemperature alarm
Contactor
Fully rated for capacitor

switching
Integral pre-charge/preinsertion module standard.

The contactor reduces
damaging switching
transients, providing safety
and durability for the
system
Lessens the chance of

disrupting sensitive
Reduced inrush current

extends the life of the
capacitor cells
UL/CSA listed
and recognized
Entire cabinet assembly is
No. 190 Listed
Capacitors are UL 810
recognized
Contactor is UL/CSA
recognized and IEC 6b
rated
Options
Optional main molded-case

circuit breaker
NEMA 3R weatherresistant enclosure
Hand-Off-Auto switches
Remote alarm relay

terminal block
Communications capable
controller
Support and Service
Renewal parts are available

through local Eaton
distributors
Factory trained service

personnel are available
through Eatons Electrical
Services & Systems
2
2
2
2
2
V3-T2-64
2.2

Product Selection
Wallmounted AUTOVAR 300 Switched Capacitor Banks

Low Voltage Applications
kvar
Step x
kvar
Base
Shipping Weight
in Lb (kg) 1
Rated Current
Amperes
Options
Option
Code
Description
Catalog
Number
240 V
Remote alarm relay terminal blockrelay terminal block for a remote

alarm to indicate controller alarm status
Communicating controller (Modbus RS-485)
25
5x5
60
217 (98.5)
25MCSR2313
50
5 x 10
120
255 (115.8)
50MCSR2313
Hand-Off-Auto switchprovides manual control to connect or disconnect capacitor H

stages regardless of controller output 2
2
2
75
5 x 15
180
260 (118.0)
75MCSR2313
Molded-case circuit breaker (see circuit breaker section)
100
5 x 20
240
270 (122.6)
100MCSR231
Weather-resistant enclosure (NEMA 3R gasketed)
125
5 x 25
300
292 (132.6)
125MCSR231
Integrated Main BreakersAUTOVAR 300
480 V
Breaker
AUTOVAR Rated Size
Current Amperes (Amperes) 3
Breaker
Interrupting
Rating (kA)
Breaker
Weight
in Lb (kg)
Standard
Wire Lug Size
50
5 x 10
60
200 (90.8)
50MCSR4313
75
5 x 15
90
210 (95.3)
75MCSR4313
kvar
100
5 x 20
120
210 (95.3)
100MCSR4313
240 V
125
5 x 25
150
240 (109.0)
125MCSR4313
25
60
125
100
10 (4.5)
(1) #3350
150
5 x 30
180
240 (109.0)
150MCSR4313
50
120
250
100
10 (4.5)
(1) #3350
175
5 x 35
210
260 (118.0)
175MCSR431
75
180
250
100
10 (4.5)
(1) #3350
100
240
400
100
10 (4.5)
(2) #3/0250
125
300
600
100
25 (11.4)
(2) #3/0350
50
60
125
65
10 (4.5)
(1) #3350
75
90
125
65
10 (4.5)
(1) #3350
200
5 x 40
241
270 (122.6)
200MCSR431
225
5 x 45
270
290 (131.7)
225MCSR431
250
5 x 50
300
292 (132.6)
250MCSR431
600 V
480 V
2
2
50
5 x 10
48
200 (90.8)
50MCSR6313
100
120
250
65
10 (4.5)
(1) #3350
75
5 x 15
72
210 (95.3)
75MCSR6313
125
150
250
65
10 (4.5)
(1) #3350
100
5 x 20
96
210 (95.3)
100MCSR6313
150
180
250
65
10 (4.5)
(1) #3350
125
5 x 25
120
240 (109.0)
125MCSR6313
175
210
400
65
10 (4.5)
(2) #3/0250
150
5 x 30
144
240 (109.0)
150MCSR6313
200
240
400
65
10 (4.5)
(2) #3/0250
225
270
400
65
10 (4.5)
(2) #3/0250
250
300
600
65
25 (11.4)
(2) #3/0350
48
125
35
10 (4.5)
(1) #3350
175
5 x 35
168
260 (118.0)
175MCSR631
200
5 x 40
192
270 (122.6)
200MCSR631
225
5 x 45
216
290 (131.7)
225MCSR631
250
5 x 50
240
292 (132.6)
250MCSR631
Spare Fuses
kvar Rating/Bank
600 V
50
75
72
125
35
10 (4.5)
(1) #3350
100
96
250
35
10 (4.5)
(1) #3350
125
120
250
35
10 (4.5)
(1) #3350
150
144
250
35
10 (4.5)
(1) #3350
175
168
250
35
10 (4.5)
(1) #3350
200
192
400
35
10 (4.5)
(2) #3/0350
240 V
480 V
600 V
Amperes
Eaton Fuse
Part Number
10
10
30
SP030217-0029J
225
216
400
35
10 (4.5)
(2) #3/0350
15
20
50
SP030217-0037D
250
240
400
35
10 (4.5)
(2) #3/0350
10
20
60
SP030217-0037E
25
2530
80
SP030217-0037G
15
30
40
100
SP030217-0037J
20
40
50
125
SP030217-0037K
25
50
150
SP030217-0037L
Renewal Parts
Description
Catalog Number
Replacement PF controller, ACX type
SP039010-0035U
Replacement contactor, 72 A
SP039010-0014B
Replacement contactor, 32 A
SP039010-0014C
Notes
1 To calculate AUTOVAR 300 weight:
1. Obtain base unit weight from table above.
2. Add option weights as necessary:
A = 1 lb
C = 1 lb
H = 5 lb
W = 10 lb
M = 50 lb enclosure weight adder plus circuit breaker weight (see circuit breaker table)
S = Consult Eatons Technical Resource Center (TRC) at 1-800-809-2772, choose option
#4, then option #2
3
4
Heavy-duty cells, 50 Hz units, and other ratings available, please consult factory. A minimum
of one CT is required per AUTOVAR unit. kvar output is voltage and frequency dependent.
60 Hz units are shown. For other voltages and frequencies, consult Eaton Technical Resource
Center (TRC) at 1-800-809-2772, choose option #4, then option #2.
Manual control is always available through controller menu system, even if the H option is
not selected.
Breakers are sized at a minimum of 135% of the unit rated Amperes per the NEC.
See equipment drawings for actual lug sizes.
V3-T2-65
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2.2
2

Dimensions
Enclosure J
Front View
Side View
0.63
(16.0)
On/Off
Switch
2
2
Power
Factor
Controller
2
2
Keylock
Handle
Blown
Fuse
Lights
2
2
29.88
(759.0)
36.00
(914.4)
0.63
(16.0)
2
2
2
Description
Height A
J1
36.00 (914.4)
14.00 (355.6)
J2
60.00 (1524.0)
14.00 (355.6)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-66
Depth B

2.2
Contents
AUTOVAR 600
Description
Page
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correction Capacitor Systems
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-49
V3-T2-51
V3-T2-54
V3-T2-63
V3-T2-68
V3-T2-69
V3-T2-73
V3-T2-74
V3-T2-81
V3-T2-83
2
2
2
2
2
2
2
2
2
2
2

Product Description
Features
Programmable to
capacitor stages to
power factor
Three-phase capacitor cell
construction
defects
Cool operating, 100%
copper wound, thermalprotected reactors are
sized up to 150% of rated
capacitor current (AUTOVAR
detuned filter only)
Service entrance or
substation power factor
correction installations
requiring precise
maintenance of target
power factor (AUTOVAR 600)
Service entrance or
requiring precise
power factor in threephase, nonlinear, high
(AUTOVAR detuned filter)
Typically connected at main
low voltage switchgear
Configuration
Cabinet: 12 gauge steel

with ANSI 61 gray, baked
finish. Removable lift bolts
standard, NEMA 1 (gasketed)

Rugged, copper busbar
connection with access
provided for top entry.
Contact factory for
availability of bottom entry.
Busbars are braced for 65
kA (optional 100 kA rating
available). All internal
power wiring connections
from bus are laid out on a
most direct basis with
minimum bends for ease
of troubleshooting. Clear
barrier limiting access to
live parts included standard
Modular tray design:

Capacitor stages arranged
in modular trays with
capacitors, fuses, clearedfuse indicating lights, and
contactors grouped in a
logical, easily understood
layout. This permits easy
access, quick identification
of operating problems, and
ease of expandability
Fusing: UL recognized,
capacity provided on all
three phases of each
stage. Blade-type fuses
mounted on insulator
stand-offs
Cleared-fuse indicating
lights: LEDs located doormounted and neon at
individual fuses to facilitate
tracing of cleared fuses
Push-to-test: Allows
testing of door-mounted
LED cleared fuse indicating
lights
AutoLocate: When door is
open and bus is energized,
fuse circuit automatically
checks for cleared fuses. If
a fuse has cleared, the light
at the fuse turns on for
easy troubleshooting
turns off control circuit
when engaged. Power
continues to be provided to
the unit until disconnect is
open
Exhaust fans: Two side
louver fans per cabinet
provide cooling and reduce
operator exposure to
discharge. Replaceable
dust filtering provided.
Dust filters can be replaced
without opening cabinet
Ease of expansion:
Capacitor stage nests are
self-contained and can be
added in the field. Two
bolts mount the nest in the
field. Control wire plugs
connect to factory
standard wire harness on
the left side of the cabinet
Ease of replacement:
Cells can be easily
replaced individually by
removing the mounting
bolt and lifting out of the
nest without removal of
any other components
ambient temperature
exceeds the maximum
and the storage
40C to +55C. For
optimal equipment life, the
temperature should not
exceed 35C annual
average, and the
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-67
2.2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2

Controller

energized stages

target power factor

values per step
Modbus)
Standard metering capability:
Voltage

only)
Frequency
Active power (kW)

distortion (VTHD)
Individual harmonic
harmonic)


displays. Controller provides
easy-to-understand alarms
for various conditions,
such as:
Undervoltage or
overvoltage
Undercurrent or
overcurrent
Target power factor

not met
Harmonic overload
Faulty step/stages
Contactor

switching

damaging switching
system


capacitor cells
Reactors
Detuning: Standard
reactor designs are
detuned to the 4.2nd
harmonic and recommended
to protect capacitors
against harmonic resonance.
Detuning to the 4.7th
harmonic is available as an
option. The harmonic
spectrum should be
evaluated for applications
involving reactors detuned
to the 4.7th harmonic to
ensure optimal equipment
life, specifically when used
in conjunction with sixpulse motor drives
Windings: 80C
temperature rise design
100% copper windings for
minimal losses
Thermal overload
protection: Each reactor
includes three normally
closed, auto reset
thermostats that open at
180C. When thermostats
engage, the contactor
opens
Insulation: 220C
insulation system
Warranty: One-year
replacement of reactors
Additional Features
Optional molded-case main
circuit breaker
Ground fault interruption

provides protection in case
of accidental contact with
Control wiringstandard
NEC color-coded modular
bundles with quick
disconnect feature for ease
of troubleshooting or ease
of expendability. UL type
MTW/AWM, CSA TEW
105C copper wire is
standard.
Optional digital metering

IQ 250
Mechanical wire lugs are

included as standard
equipment. Typical phase
lugs range from (2) 6
AWG350 kcmil to (4) 3
AWG750 MCM. Typical
ground lug can accept wire
from 6 AWG to 350 kcmil.
Lugs are compatible with
copper wire 90C
Heavy-duty capacitor cells

are standard on AUTOVAR
detuned filter and optional
on AUTOVAR 600. For 480 V
units, standard-duty cells
are 525 V rated, and heavyduty cells are 600 V rated
AUTOVAR 600Interior View
Support and service

through local Eaton
distributors

Services & Systems
Modular Step Nest Assembly
Dust Filter Tray
2
2
2
2
V3-T2-68

No. 190 Listed
recognized
Contactor is UL/CSA
recognized and
IEC 6b rated

2.2
Product Selection
OptionsAUTOVAR 600 and AUTOVAR Detuned Filter
Option
Code
Description
Remote alarm relay terminal blockrelay terminal block for a remote alarm to
indicate controller alarm status
Fully insulated main bus
Communicating PF controller (Modbus RS-485)
Hand-off-auto switch provides manual control to connect or disconnect capacitor

Integrated main breaker
Integrated main breaker with high interrupting rating (see breaker table
for more information), includes 100 kA busbar bracing
M1
100 kA busbar bracing
N1
Integrated CVX series surge protection, without sine wave tracking
T1
Integrated SPD series surge protection, 160 kA per phase,

with sine wave tracking
T2
IQ 250 electronic meter 2
Weather resistant enclosure (NEMA 3R gasketed) 3
Standard filter detuned to the 4.2nd harmonic 4
2
2
2
2
Notes
1 Manual control is always available through menu controller on system, even if the H option is
not selected.
2 Not available on NEMA 3R units (W option).
3 Only available on AUTOVAR 600 with heavy-duty cells and AUTOVAR detuned filters
using L + L, L + KK, and KK + KK enclosures.
4 Tuning to the 4.2nd harmonic is the preferred option. Other tunings available. Contact Eatons
Technical Resource Center (TRC) power factor application engineers at 1-800-809-2772,
choose option #4, then option #2.
2
2
2
To calculate AUTOVAR 600 or AUTOVAR detuned filter weight:

Obtain base unit weight from tables on Pages V3-T2-70V3-T2-72
(as appropriate).
Add option weights as necessary:
A = 1 lb (0.5 kg)
B = 10 lb (4.5 kg)
C = 1 lb (0.5 kg)
H = 10 lb (4.5 kg)
M = Circuit breaker weight (see circuit breaker table)
M1 = 10 lb (4.5 kg) hardware weight adder plus circuit breaker
weight (see circuit breaker table)
N1 = 10 lb (4.5 kg)
T1 = 5 lb (2.3 kg)
T2 = 10 lb (4.5 kg)
Q = 5 lb (2.3 kg)
W = 10 lb (4.5 kg) per door
Y = 0 lb (0 kg)
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-69
2.2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
AUTOVAR 600 Floor-Mounted Switched Capacitor Banks

Units with Standard-Duty CellsLow Voltage Applications
2
2
kvar 1
240 Vac
75
100
125
150
200
250
300
350
400
480 Vac
100
150
200
250
300
350
400
450
500
550
600
660
700
720
800
900
1000
1100
1200
600 Vac
100
150
200
250
300
350
400
450
500
550
600
660
700
720
800
900
1000
1100
1200
Step x
kvar
Rated
Current
Amperes
Base
Shipping
Weight
in Lb (kg)
Base
Catalog
Number
3 x 25
4 x 25
5 x 25
6 x 25
8 x 25
10 x 25
12 x 25
7 x 50
8 x 50
180
240
300
361
481
600
720
844
965
644 (292.4)
692 (314.2)
740 (336.0)
788 (357.8)
884 (401.3)
944 (428.6)
1022 (464.0)
1616 (734.0)
1704 (774.0)
75TPCSR231
100TPCSR231
125TPCSR231
150TPCSR231
200TPCSR231
250TPCSR231
300TPCSR231
350TPCSR231
400TPCSR231
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 50
12 x 50
11 x 60
7 x 100
12 x 60
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
120
180
240
300
360
420
480
540
600
660
720
792
840
864
960
1080
1200
1320
1440
588 (266.7)
632 (287.0)
676 (306.9)
720 (326.9)
764 (346.9)
808 (366.8)
852 (386.8)
896 (406.8)
944 (428.6)
984 (446.7)
1022 (464.0)
1010 (458.5)
1616 (734.0)
1050 (476.7)
1704 (774.0)
1792 (814.0)
1888 (857.0)
1966 (893.0)
2044 (928.0)
100TPCSR431
150TPCSR431
200TPCSR431
250TPCSR431
300TPCSR431
350TPCSR431
400TPCSR431
450TPCSR431
500TPCSR431
550TPCSR431
600TPCSR431
660TPCSR431
700TPCSR431
720TPCSR431
800TPCSR431
900TPCSR431
1000TPCSR431
1100TPCSR431
1200TPCSR431
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 60
12 x 50
11 x 60
7 x 100
12 x 60
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
46
144
192
240
288
336
384
432
480
528
576
634
672
692
768
864
960
1056
1152
588 (266.7)
632 (287.0)
676 (306.9)
720 (326.9)
764 (346.9)
808 (366.8)
852 (386.8)
896 (406.8)
944 (428.6)
984 (446.7)
1022 (464.0)
1010 (458.5)
1616 (734.0)
1050 (476.7)
1704 (774.0)
1792 (814.0)
1888 (857.0)
1966 (893.0)
2044 (928.0)
100TPCSR631
150TPCSR631
200TPCSR631
250TPCSR631
300TPCSR631
350TPCSR631
400TPCSR631
450TPCSR631
500TPCSR631
550TPCSR631
600TPCSR631
660TPCSR631
700TPCSR631
720TPCSR631
800TPCSR631
900TPCSR631
1000TPCSR631
1100TPCSR631
1200TPCSR631
AUTOVAR 600 Sizing Chart for Units with

Standard-Duty Cells
Enclosure Size 2
kvar
240 V
75
100
125
150
200
250
300
350
400
480 V
100
150
200
250
300
350
400
450
500
550
600
660
700
720
800
900
1000
1100
1200
600 V
100
150
200
250
300
350
400
450
500
550
600
660
700
720
800
900
1000
1100
1200
Step x
kvar
NEMA 1, without Main

Breaker, No Suffix
NEMA 1, with Main

Breaker, M Suffix
3 x 25
4 x 25
5 x 25
6 x 25
8 x 25
10 x 25
12 x 25
7 x 50
8 x 50
L
L
L
L
L
L
L
KK
KK
L
L
L
L
L
L
L
KK
C/F
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 50
12 x 50
11 x 60
14 x 50
12 x 60
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
L
L
L
L
L
L
L
L
L
L
L
L
KK
L
KK
KK
KK
KK
KK
L
L
L
L
L
L
L
L
L
L
L
L
KK
L
C/F
C/F
C/F
C/F
C/F
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 50
12 x 50
11 x 60
14 x 50
12 x 60
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
L
L
L
L
L
L
L
L
L
L
L
L
KK
L
KK
KK
KK
KK
KK
L
L
L
L
L
L
L
L
L
L
L
L
KK
L
KK
KK
C/F
C/F
C/F
Notes
1 Other ratings available. Please consult factory. kvar output is voltage and frequency
dependent. 60 Hz units are shown. For other voltages and frequencies, consult Eaton
Technical Resource Center (TRC) at 1-800-809-2772, choose option #4, then option #2.
2 Enclosure sizing for units with integrated surge protection or bottom entry can vary
and may not be available on all kvar sizes. Contact Eatons Technical Resource Center at
1-800-809-2772, choose option #4, then option #2.
2
2
2
C/F = Consult factory

V3-T2-70

AUTOVAR 600 Floor-Mounted Switched Capacitor Banks

Units with Heavy-Duty CellsLow Voltage Applications
kvar
240 Vac
75
100
125
150
200
250
300
350
400
480 Vac
100
150
200
250
300
350
400
450
500
550
600
700
800
900
1000
1100
1200
600 Vac
100
150
200
250
300
350
400
450
500
550
600
700
800
900
1000
1100
1200
Step x
kvar
Rated
Current
Amperes
Base
Shipping
Weight in
Lb (kg)
Base
Catalog
Number
3 x 25
4 x 25
5 x 25
6 x 25
8 x 25
10 x 25
12 x 25
7 x 50
8 x 50
180
240
300
361
481
601
720
844
965
659 (298.9)
712 (323.0)
765 (347.0)
818 (371.0)
924 (419.1)
994 (450.9)
1082 (490.8)
1686 (764.8)
1784 (809.2)
75TPHSR231
100TPHSR231
125TPHSR231
150TPHSR231
200TPHSR231
250TPHSR231
300TPHSR231
350TPHSR231
400TPHSR231
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 50
12 x 50
14 x 50
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
120
180
240
300
360
420
480
540
600
660
720
792
462
1083
1203
1323
1443
617 (279.9)
677 (307.1)
736 (333.8)
795 (360.6)
854 (387.4)
913 (414.1)
972 (440.9)
1031 (467.7)
1094 (496.2)
1149 (521.2)
1202 (545.2)
1826 (828.3)
1944 (881.8)
2062 (935.3)
2198 (997.0)
2296 (1041.4)
2404 (1090.4)
100TPHSR431
150TPHSR431
200TPHSR431
250TPHSR431
300TPHSR431
350TPHSR431
400TPHSR431
450TPHSR431
500TPHSR431
550TPHSR431
600TPHSR431
700TPHSR431
800TPHSR431
900TPHSR431
1000TPHSR431
1100TPHSR431
1200TPHSR431
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 60
12 x 50
7 x 100
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
96
144
192
240
288
336
384
432
480
529
576
672
768
864
962
1058
1155
617 (279.9)
677 (307.1)
736 (333.8)
795 (360.6)
854 (387.4)
913 (414.1)
972 (440.9)
1031 (467.7)
1094 (496.2)
1149 (521.2)
1202 (545.2)
1826 (828.3)
1944 (881.8)
2062 (935.3)
2198 (997.0)
2296 (1041.4)
2404 (1090.4)
100TPHSR631
150TPHSR631
200TPHSR631
250TPHSR631
300TPHSR631
350TPHSR631
400TPHSR631
450TPHSR631
500TPHSR631
550TPHSR631
600TPHSR631
700TPHSR631
800TPHSR631
900TPHSR631
1000TPHSR631
1100TPHSR631
1200TPHSR631
2.2
AUTOVAR 600 Sizing Chart for Units with Heavy-Duty Cells

Enclosure Size 2
kvar
240 V
75
100
125
150
200
250
300
350
400
480 V
100
150
200
250
300
350
400
450
500
550
600
700
800
900
1000
1100
1200
600 V
100
150
200
250
300
350
400
450
500
550
600
700
800
900
1000
1100
1200
Step x
kvar
NEMA 1,
without Main
Breaker,
No Suffix
NEMA 1,
with Main
Breaker,
M Suffix
NEMA 3R,
without Main
Breaker,
W Suffix
NEMA 3R,
with Main
Breaker,
MW Suffix
3 x 25
4 x 25
5 x 25
6 x 25
8 x 25
10 x 25
12 x 25
7 x 50
8 x 50
L
L
L
L
L
L
L
L
KK
L
L
L
L
L
L
L
KK
C/F
L
L
L
L
L
L
L
KK
KK
L
L
L
L
L
L
L
KK
C/F
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 50
12 x 50
14 x 50
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
L
L
L
L
L
L
L
L
L
L
L
KK
KK
KK
KK
KK
KK
L
L
L
L
L
L
L
L
L
L
L
KK
C/F
C/F
C/F
C/F
C/F
L
L
L
L
L
L
L
L
L
L
L
KK
KK
KK
KK
KK
KK
L
L
L
L
L
L
L
L
L
L
L
KK
C/F
C/F
C/F
C/F
C/F
2 x 50
3 x 50
4 x 50
5 x 50
6 x 50
7 x 50
8 x 50
9 x 50
10 x 50
11 x 50
12 x 50
14 x 50
8 x 100
9 x 100
10 x 100
11 x 100
12 x 100
L
L
L
L
L
L
L
L
L
L
L
KK
KK
KK
KK
KK
KK
L
L
L
L
L
L
L
L
L
L
L
KK
KK
KK
C/F
C/F
C/F
L
L
L
L
L
L
L
L
L
L
L
KK
KK
KK
KK
KK
KK
L
L
L
L
L
L
L
L
L
L
L
KK
KK
KK
C/F
C/F
C/F
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Notes
1 Other ratings available. Please consult factory. kvar output is voltage and frequency
dependent. 60 Hz units are shown. For other voltages and frequencies, consult Eaton
Technical Resource Center (TRC) at 1-800-809-2772, choose option #4, then option #2.
2
2
2
2
2
V3-T2-71
2.2
2
2

Floor-Mounted Switched Detuned FiltersLow Voltage
kvar 1
Step x
kvar
Rated
Current
Amperes
Base
Shipping
Weight
in Lb (kg)
AUTOVAR Detuned Filter Sizing Chart

Enclosure Size 2
Base
Catalog Number
Step x
kvar
NEMA 1
without Main
Breaker,
No Suffix
NEMA 1
with Main
Breaker,
M Suffix
NEMA 3R
without Main
Breaker,
W Suffix
NEMA 3R
with Main
Breaker,
MW Suffix
240 Vac
150
6 x 25
361
1830 (830.8)
150THFSR232Y
240 V
200
8 x 25
481
2222 (1008.8
200THFSR232Y
150
6 x 25
L+L3
L+L3
L+L3
L+L3
250
10 x 25
601
2525 (1146.4)
250THFSR232Y
200
8 x 25
L+L3
L+L3
L+L3
L+L3
300
12 x 25
720
2830 (1284.8)
300THFSR232Y
250
10 x 25
L+L3
L+L3
L+L3
L+L3
350
7 x 50
844
3090 (1401.6)
350THFSR231Y
300
12 x 25
L+L3
KK
L+L3
KK
400
8 x 50
965
3560 (1614.8)
400THFSR232Y
350
7 x 50
KK
L + KK 3
L + KK 3
KK
480 Vac
400
8 x 50
L + KK 3
C/F
L + KK 3
C/F
100
2 x 50
120
1105 (501.2)
100THFSR431Y
480 V
150
3 x 50
180
1242 (564.6)
150THFSR431Y
100
2 x 50
L+L3
L+L3
200
4 x 50
240
1438 (652.9)
200THFSR431Y
150
3 x 50
L+L3
L+L3
250
5 x 50
300
1634 (741.8)
250THFSR431Y
200
4 x 50
L+L3
L+L3
300
6 x 50
360
1830 (830.8)
300THFSR432Y
L+L
L+L3
350
7 x 50
420
2026 (919.8)
350THFSR432Y
300
6 x 50
L+L
L+L
L+L3
400
8 x 50
480
2222 (1008.8)
400THFSR432Y
350
7 x 50
L+L3
L+L3
L+L3
L+L3
450
9 x 50
540
2371 (1076.4)
450THFSR432Y
400
8 x 50
L+L3
L+L3
L+L3
L+L3
500
10 x 50
600
2525 (1146.4)
500THFSR432Y
450
9 x 50
L+L3
L+L3
L+L3
L+L3
550
11 x 50
660
2750 (1248.5)
550THFSR432Y
500
10 x 50
L+L3
L+L3
L+L3
L+L3
12 x 50
720
2830 (1284.8)
600THFSR432Y
550
11 x 50
L+L
600
700
7 x 100
792
3090 (1401.6)
700THFSR431Y
600
12 x 50
L+L3
800
8 x 100
962
3560 (1614.8)
800THFSR432Y
700
7 x 100
900
9 x 100
1083
3900 (1769.0)
900THFSR432Y
800
1000
10 x 100
1203
4240 (1923.2)
1000THFSR432Y
1100
11 x 100
1323
4500 (2041.2)
1100THFSR432Y
2
2
kvar
250
5 x 50
L
3
L+L
L+L
KK
L+L
L + KK 3
KK
L+L3
L + KK 3
KK
KK
L + KK 3
L + KK 3
8 x 100
L + KK 3
C/F
L + KK 3
C/F
900
9 x 100
KK + KK 3
C/F
KK + KK 3
C/F
1000
10 x 100
KK + KK 3
C/F
KK + KK 3
C/F
1100
11 x 100
KK + KK 3
C/F
KK + KK 3
C/F
600 Vac
100
2 x 50
96
1105 (501.2)
100THFSR631Y
600 V
150
3 x 50
144
1242 (564.6)
150THFSR631Y
100
2 x 50
L+L3
L+L3
200
4 x 50
192
1438 (652.9)
200THFSR631Y
150
3 x 50
L+L3
L+L3
250
5 x 50
240
1634 (741.8)
250THFSR631Y
200
4 x 50
L+L3
L+L3
300
6 x 50
288
1830 (830.8)
300THFSR632Y
L+L
L+L3
350
7 x 50
336
2026 (919.8)
350THFSR632Y
300
6 x 50
L+L
L+L
L+L3
400
8 x 50
384
2222 (1008.8)
400THFSR632Y
350
7 x 50
L+L3
L+L3
L+L3
L+L3
450
9 x 50
432
2371 (1076.4)
450THFSR632Y
400
8 x 50
L+L3
L+L3
L+L3
L+L3
500
10 x 50
480
2525 (1146.4)
500THFSR632Y
450
9 x 50
L+L3
L+L3
L+L3
L+L3
550
11 x 50
529
2750 (1248.5)
550THFSR632Y
500
10 x 50
L+L3
L+L3
L+L3
L+L3
600
12 x 50
576
2830 (1284.8)
600THFSR632Y
11 x 50
L+L
700
7 x 100
672
3090 (1401.6)
700THFSR631Y
600
12 x 50
L+L
800
8 x 100
768
3560 (1614.8)
800THFSR632Y
700
7 x 100
KK
900
9 x 100
864
3900 (1769.0)
900THFSR632Y
800
8 x 100
L + KK 3
1000
10 x 100
962
4240 (1923.2)
1000THFSR632Y
900
9 x 100
1100
11 x 100
1058
4500 (2041.2)
1100THFSR632Y
1000
1100
250
550
5 x 50
L
3
L+L
L+L
L+L
L + KK 3
KK
L+L
L + KK 3
KK
L + KK 3
L + KK 3
L + KK 3
L + KK 3
L + KK 3
KK + KK 3
KK + KK 3
KK + KK 3
KK + KK 3
10 x 100
KK + KK 3
C/F
KK + KK 3
C/F
11 x 100
KK + KK 3
C/F
KK + KK 3
C/F
KK
Notes
1 kvar output is voltage and frequency dependent. 60 Hz units are shown. For other voltages
and frequencies, consult Eaton Technical Resource Center (TRC) at 1-800-809-2772, choose
option #4, then option #2.
3 Dual enclosure design requires customer installation of factory supplied interconnecting
wires.
2
2
2
2
2
V3-T2-72

2.2
Dimensions
Enclosure L Front View
Standard Customer Conduit

Entry in This Area
Power
Conductor
Lugs
POWER
FACTOR
CORRECTION
69B1007G01
1
2
3
Option W NEMA 3R
Drip Shield
2
2
Exhaust
Power Factor Controller
BLR-ACX
Option M
Molded-Case
Circuit Breaker
esc
PHASE A
PHASE B
PHASE C
DANGER
HIGH VOLTAGE
CAUTION
DISCONNECT
Ground
Lug
BEFORE SERVICING
78.00
(1981.2)
Copper
Busbar
2
A
A
38.50
(977.9)
Dust/Air Filter Tray
41.30 (1049.0)
Mounting Holes
0.438-Inch Dia. Typ.
25.00
(635.0) 16.00
(406.4)
25.00
(635.0)
Legend
1. Controller
2. On/Off Switch
3. Cleared Fuse Indicating Lights
Notes:
1. 6-Inch Minimum Clearance Each Side
2. 45-Inch Front Clearance or per Local Code
Air Filter
Section A-A
Enclosure KK Front and Side Views

Option W NEMA 3R Drip Shield
Customer Conduit Entry in This Area
Power
Conductor
Lugs
POWER
FACTOR
CORRECTION
69B1007G01
1
2
3
BLR-ACX
esc
PHASE A
PHASE B
2
2
Exhaust
Ground
Lug
PHASE C
Option M
Molded-Case
Circuit Breaker
78.00
(1981.2)
Copper
Busbar
2
2
A
25.00
(635.0)
77.64 (1972.0)
80.40 (2042.1)
25.00 16.00
(635.0) (406.4)
Air Filter
Air Filter
Mounting Holes
Legend
1. Controller
2. On/Off Switch
2
2
Notes:
Section A-A
V3-T2-73
2.2
2

Contents
AUTOVAR Filter
Description
Page
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOVAR FilterLV Automatic Detuned Filter
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . .
HCU2 Harmonic Correction Unit. . . . . . . . . . . . . .
2
2
2
2
2
2
V3-T2-49
V3-T2-51
V3-T2-54
V3-T2-63
V3-T2-67
V3-T2-75
V3-T2-76
V3-T2-78
V3-T2-81
V3-T2-83
2
2
2
AUTOVAR FilterLV Automatic Detuned Filter
Product Description
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Programmable to
capacitor stages to
power factor
Three-phase capacitor cell
construction
defects
Cool operating, 100%
copper wound, thermalprotected reactors are
sized up to 150% of rated
capacitor current (AUTOVAR
detuned filter only)
Service entrance or
requiring precise
power factor (AUTOVAR 600)
Service entrance or
requiring precise
power factor in threephase, nonlinear, high
(AUTOVAR detuned filter)
Typically connected at main
low voltage switchgear
2
2
V3-T2-74
Features
Configuration
Cabinet: 12 gauge steel

with ANSI 61 gray, baked
finish. Removable lift bolts
standard, NEMA 1 (gasketed)

Rugged, copper busbar
connection with access
provided for top entry.
Contact factory for
availability of bottom entry.
Busbars are braced for 65
kA (optional 100 kA rating
available). All internal
power wiring connections
from bus are laid out on a
most direct basis with
minimum bends for ease
of troubleshooting. Clear
barrier limiting access to
live parts included standard
Modular tray design:

Capacitor stages arranged
in modular trays with
capacitors, fuses, clearedfuse indicating lights, and
contactors grouped in a
logical, easily understood
layout. This permits easy
access, quick identification
of operating problems, and
ease of expandability
Fusing: UL recognized,
capacity provided on all
three phases of each
stage. Blade-type fuses
mounted on insulator
stand-offs
Cleared-fuse indicating
lights: LEDs located doormounted and neon at
individual fuses to facilitate
tracing of cleared fuses
Push-to-test: Allows
testing of door-mounted
LED cleared fuse indicating
lights
AutoLocate: When door is
open and bus is energized,
fuse circuit automatically
checks for cleared fuses. If
a fuse has cleared, the light
at the fuse turns on for
easy troubleshooting
turns off control circuit
when engaged. Power
continues to be provided to
the unit until disconnect is
open
Exhaust fans: Two side
louver fans per cabinet
provide cooling and reduce
operator exposure to
discharge. Replaceable
dust filtering provided.
Dust filters can be replaced
without opening cabinet
Ease of expansion:
Capacitor stage nests are
self-contained and can be
added in the field. Two
bolts mount the nest in the
field. Control wire plugs
connect to factory
standard wire harness on
the left side of the cabinet
Ease of replacement:
Cells can be easily
replaced individually by
removing the mounting
bolt and lifting out of the
nest without removal of
any other components
ambient temperature
exceeds the maximum
and the storage
40C to +55C. For
optimal equipment life, the
temperature should not
exceed 35C annual
average, and the

Controller

energized stages

target power factor

values per step
Modbus)
Standard metering capability:
Voltage

only)
Frequency
Active power (kW)

distortion (VTHD)
Individual harmonic
harmonic)


displays. Controller provides
easy-to-understand alarms
for various conditions,
such as:
Undervoltage or
overvoltage
Undercurrent or
overcurrent
Target power factor

not met
Harmonic overload
Faulty step/stages
Contactor

switching

damaging switching
system


capacitor cells
Reactors
Detuning: Standard
reactor designs are
detuned to the 4.2nd
harmonic and recommended
to protect capacitors
against harmonic resonance.
Detuning to the 4.7th
harmonic is available as an
option. The harmonic
spectrum should be
evaluated for applications
involving reactors detuned
to the 4.7th harmonic to
ensure optimal equipment
life, specifically when used
in conjunction with sixpulse motor drives
Windings: 80C
temperature rise design
100% copper windings for
minimal losses
Thermal overload
protection: Each reactor
includes three normally
closed, auto reset
thermostats that open at
180C. When thermostats
engage, the contactor
opens
Insulation: 220C
insulation system
Warranty: One-year
replacement of reactors
Additional Features
Optional molded-case main
circuit breaker
Ground fault interruption

provides protection in case
of accidental contact with
Control wiringstandard
NEC color-coded modular
bundles with quick
disconnect feature for ease
of troubleshooting or ease
of expendability. UL type
MTW/AWM, CSA TEW
105C copper wire is
standard.
Optional digital metering

IQ 250
Mechanical wire lugs are

included as standard
equipment. Typical phase
lugs range from (2) 6
AWG350 kcmil to (4) 3
AWG750 MCM. Typical
ground lug can accept wire
from 6 AWG to 350 kcmil.
Lugs are compatible with
copper wire 90C
Heavy-duty capacitor cells

are standard on AUTOVAR
detuned filter and optional
on AUTOVAR 600. For 480 V
units, standard-duty cells
are 525 V rated, and heavyduty cells are 600 V rated
2.2
2
2
2
2
2
2
2
2
2
2
AUTOVAR FilterReactor Cabinet

No. 190 Listed
recognized
Contactor is UL/CSA
recognized and
IEC 6b rated
2
2
2
2
2
2
2
Support and service

through local Eaton
distributors

Services & Systems
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-75
2.2

Product Selection
OptionsAUTOVAR 600 and AUTOVAR Detuned Filter
Description
2
2
Option
Code
Remote alarm relay terminal blockrelay terminal block for a remote alarm to
indicate controller alarm status
Fully insulated main bus
Communicating PF controller (Modbus RS-485)
Hand-off-auto switch provides manual control to connect or disconnect capacitor

Integrated main breaker
Integrated main breaker with high interrupting rating (see breaker table
for more information), includes 100 kA busbar bracing
M1
100 kA busbar bracing
N1
Integrated CVX series surge protection, without sine wave tracking
T1
Integrated SPD series surge protection, 160 kA per phase,

with sine wave tracking
T2
IQ 250 electronic meter 2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Weather resistant enclosure (NEMA 3R gasketed)
Standard filter detuned to the 4.2nd harmonic 4
W
Y
Notes
1 Manual control is always available through menu controller on system, even if the H option is
not selected.
2 Not available on NEMA 3R units (W option).
3 Only available on AUTOVAR 600 with heavy-duty cells and AUTOVAR detuned filters
using L + L, L + KK, and KK + KK enclosures.
4 Tuning to the 4.2nd harmonic is the preferred option. Other tunings available. Contact Eatons
Technical Resource Center (TRC) power factor application engineers at 1-800-809-2772,
choose option #4, then option #2.
To calculate AUTOVAR 600 or AUTOVAR detuned filter weight:
Obtain base unit weight from table on Page V3-T2-77 (as appropriate).
Add option weights as necessary:
A = 1 lb (0.5 kg)
B = 10 lb (4.5 kg)
C = 1 lb (0.5 kg)
H = 10 lb (4.5 kg)
M = Circuit breaker weight (see circuit breaker table)
M1 = 10 lb (4.5 kg) hardware weight adder plus circuit breaker
weight (see circuit breaker table)
N1 = 10 lb (4.5 kg)
T1 = 5 lb (2.3 kg)
T2 = 10 lb (4.5 kg)
Q = 5 lb (2.3 kg)
W = 10 lb (4.5 kg) per door
Y = 0 lb (0 kg)
2
2
2
2
2
2
2
2
2
V3-T2-76
2.2

Floor-Mounted Switched Detuned FiltersLow Voltage
AUTOVAR Detuned Filter Sizing Chart
Step x
kvar
Rated
Current
Amperes
Base
Shipping
Weight
in Lb (kg)
Base
Catalog Number
6 x 25
361
1830 (830.8)
150THFSR232Y
240 V
200
8 x 25
481
2222 (1008.8
200THFSR232Y
150
250
10 x 25
601
2525 (1146.4)
250THFSR232Y
200
300
12 x 25
720
2830 (1284.8)
300THFSR232Y
250
350
7 x 50
844
3090 (1401.6)
350THFSR231Y
300
400
8 x 50
965
3560 (1614.8)
400THFSR232Y
350
kvar 1
kvar
240 Vac
150
Enclosure Size 2
480 Vac
NEMA 1
without Main
Breaker,
No Suffix
NEMA 1
with Main
Breaker,
M Suffix
NEMA 3R
without Main
Breaker,
W Suffix
NEMA 3R
with Main
Breaker,
MW Suffix
6 x 25
L+L3
L+L3
L+L3
L+L3
8 x 25
L+L3
L+L3
L+L3
L+L3
10 x 25
L+L3
L+L3
L+L3
L+L3
12 x 25
L+L3
KK
L+L3
KK
7 x 50
KK
L + KK 3
L + KK 3
KK
Step x
kvar
L+L3
L+L3
L+L3
L+L3
L+L
L+L3
L+L3
L+L3
L+L3
L+L3
L+L3
L+L3
L+L3
L+L3
L+L3
L+L3
8 x 50
L+L3
L+L3
L+L3
L+L3
9 x 50
L+L3
L+L3
L+L3
L+L3
10 x 50
L+L3
L+L3
L+L3
L+L3
11 x 50
L+L
600
12 x 50
700
7 x 100
900THFSR432Y
800
1000THFSR432Y
900
1100THFSR432Y
1000
L + KK
100
2 x 50
150
3 x 50
120
1105 (501.2)
100THFSR431Y
480 V
150
3 x 50
180
1242 (564.6)
150THFSR431Y
200
4 x 50
240
1438 (652.9)
200THFSR431Y
250
5 x 50
300
1634 (741.8)
250THFSR431Y
200
4 x 50
300
6 x 50
360
1830 (830.8)
300THFSR432Y
250
5 x 50
350
7 x 50
420
2026 (919.8)
350THFSR432Y
300
6 x 50
400
8 x 50
480
2222 (1008.8)
400THFSR432Y
350
7 x 50
450
9 x 50
540
2371 (1076.4)
450THFSR432Y
400
500
10 x 50
600
2525 (1146.4)
500THFSR432Y
450
550
11 x 50
660
2750 (1248.5)
550THFSR432Y
500
600
12 x 50
720
2830 (1284.8)
600THFSR432Y
550
700
7 x 100
792
3090 (1401.6)
700THFSR431Y
800
8 x 100
962
3560 (1614.8)
800THFSR432Y
900
9 x 100
1083
3900 (1769.0)
1000
10 x 100
1203
4240 (1923.2)
1100
11 x 100
1323
4500 (2041.2)
600 Vac
1100
C/F
L+L
2
2
2
2
2
KK
L+L
L + KK 3
L+L3
KK
L+L3
L + KK 3
KK
KK
L + KK 3
L + KK 3
8 x 100
L + KK 3
C/F
L + KK 3
C/F
9 x 100
KK + KK 3
C/F
KK + KK 3
C/F
10 x 100
KK + KK 3
C/F
KK + KK 3
C/F
11 x 100
KK + KK
C/F
KK + KK 3
C/F
2
2
2 x 50
96
1105 (501.2)
100THFSR631Y
600 V
150
3 x 50
144
1242 (564.6)
150THFSR631Y
100
2 x 50
L+L3
L+L3
200
4 x 50
192
1438 (652.9)
200THFSR631Y
150
3 x 50
L+L3
L+L3
250
5 x 50
240
1634 (741.8)
250THFSR631Y
200
4 x 50
L+L3
L+L3
300
6 x 50
288
1830 (830.8)
300THFSR632Y
250
5 x 50
L+L3
L+L3
L+L3
350
7 x 50
336
2026 (919.8)
350THFSR632Y
300
6 x 50
L+L3
L+L3
L+L3
L+L3
400
8 x 50
384
2222 (1008.8)
400THFSR632Y
350
7 x 50
L+L3
L+L3
L+L3
L+L3
450
9 x 50
432
2371 (1076.4)
450THFSR632Y
400
8 x 50
L+L3
L+L3
L+L3
L+L3
500
10 x 50
480
2525 (1146.4)
500THFSR632Y
450
9 x 50
L+L3
L+L3
L+L3
L+L3
550
11 x 50
529
2750 (1248.5)
550THFSR632Y
500
10 x 50
L+L
600
12 x 50
576
2830 (1284.8)
600THFSR632Y
550
11 x 50
L+L3
KK
L+L3
L + KK 3
700
7 x 100
672
3090 (1401.6)
700THFSR631Y
600
12 x 50
L+L3
KK
L+L3
L + KK 3
800
8 x 100
768
3560 (1614.8)
800THFSR632Y
700
7 x 100
KK
KK
L + KK 3
L + KK 3
900
9 x 100
864
3900 (1769.0)
900THFSR632Y
800
8 x 100
L + KK 3
L + KK 3
L + KK 3
L + KK 3
1000
10 x 100
962
4240 (1923.2)
1000THFSR632Y
900
9 x 100
KK + KK 3
KK + KK 3
KK + KK 3
KK + KK 3
1100
11 x 100
1058
4500 (2041.2)
1100THFSR632Y
1000
10 x 100
KK + KK 3
C/F
KK + KK 3
C/F
11 x 100
C/F
KK + KK 3
C/F
KK + KK
L+L
L+L
2
2
2
100
1100
L + KK
8 x 50
2 x 50
C/F
400
100
L+L
Notes
1 kvar output is voltage and frequency dependent. 60 Hz units are shown. For other voltages
and frequencies, consult Eaton Technical Resource Center (TRC) at 1-800-809-2772, choose
option #4, then option #2.
3 Dual enclosure design requires customer installation of factory supplied interconnecting
wires.
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-77
2.2
2
2
2

Dimensions
AUTOVAR L (Single Door) Enclosure
Standard Customer Conduit
Entry in This Area
2
2
2
2
Option W NEMA 3R
Drip Shield
Power
Conductor
Lugs
POWER
FACTOR
CORRECTION
69B1007G01
1
2
3
Exhaust
BLR-ACX
Option M
Molded-Case
Circuit Breaker
esc
PHASE A
PHASE B
PHASE C
DANGER
HIGH VOLTAGE
CAUTION
DISCONNECT
Ground
Lug
BEFORE SERVICING
78.00
(1981.2)
Copper
Busbar
2
2
38.50
(977.9)
2
2
2
41.30 (1049.0)
Mounting Holes
25.00
(635.0) 16.00
(406.4)
25.00
(635.0)
Legend
1. Controller
2. On/Off Switch
Air Filter
Notes:
2
2
Section A-A
AUTOVAR KK (Double Door) Enclosure
Power
Conductor
Lugs
POWER
FACTOR
CORRECTION
69B1007G01
1
2
3
BLR-ACX
esc
PHASE A
PHASE B
Exhaust
Ground
Lug
PHASE C
Option M
Molded-Case
Circuit Breaker
78.00
(1981.2)
Copper
Busbar
2
2
2
77.64 (1972.0)
2
2
25.00
(635.0)
80.40 (2042.1)
25.00 16.00
(635.0) (406.4)
Air Filter
Air Filter
Mounting Holes
Legend
1. Controller
2. On/Off Switch
Notes:
Section A-A
2
V3-T2-78
2.2

AUTOVAR L + L (2 Single Door) Enclosures
POWER
FACTOR
CORRECTION
69B1007G01
1
2
3
Option M
Molded-Case
Circuit Breaker
BLR-CX
PHASE A
PHASE B
Power
Conductor
Lugs
Exhaust
PHASE C
DANGER
DANGER
HIGH VOLTAGE
HIGH VOLTAGE
CAUTION
CAUTION
DISCONNECT
DISCONNECT
BEFORE SERVICING
BEFORE SERVICING
Capacitor
Enclosure
Ground
Lug
78.00
(1981.2)
Reactor
Enclosure
Copper
Busbar
2
2
Dust/Air
Filter Tray
Typ.
38.50 (977.9)
Factory Supplied 12-Inch Conduit and

Power/Control Cables. Interconnect in Field
by Customer/Installing Contractor Required
25.00
16.00
(635.0)
(406.4)
Air Filter
Mounting Holes
Air Filter
Section A-A
Legend
1. Controller
2. On/Off Switch
41.26 (1048.0)
Notes:
3. 12-Inch Minimum Separation Between Enclosures
Section B-B
BLR-ACX
esc
PHASE B
Exhaust
DANGER
HIGH VOLTAGE
CAUTION
78.00
(1981.2)
BEFORE SERVICING
Capacitor
Enclosure
Reactor
Enclosure
2
2
PHASE C
DISCONNECT
2
2
Power
Conductor
Ground
Lugs
Lug
PHASE A
2
2
L + KK Enclosure (AUTOVAR Detuned Filter Only)
2
3
2
2
Copper
Busbar
2
A
B
77.64 (1972.0)

41.26 (1048.1)
25.00 16.00
(635.0) (406.4)
Air Filter
Section A-A
38.50 (977.9)
Dust/Air
Filter Tray Typ.
Legend
1. Controller
2. On/Off Switch
2
2
80.40 (2042.1)
Air Filter
Air Filter
Section B-B
Mounting Holes
Notes:
1. 6-Inch Minimum Clearance
Each Side
2. 45-Inch Front Clearance or per
Local Code
3. 12-Inch Minimum Separation
Between Enclosures
2
2
2
V3-T2-79
2.2

AUTOVAR KK + KK Enclosures
Option W NEMA 3R
Drip Shield
Exhaust
Standard Customer Conduit Entry in This Area
2
2
2
3
POWER
FACTOR
CORRECTION
Power
Conductor
Lugs
POWER
FACTOR
CORRECTION
69B1007G01
69B1007G01
BLR-ACX
esc
PHASE A
PHASE B
PHASE C
Ground
Lug
78.00
(1981.2)
Capacitor
Enclosure
2
2
B
Dust/Air
Filter Tray
2
2
77.64 (1972.1)
2
2
Copper
Busbar
Reactor
Enclosure
80.40 (2042.1)
25.00 16.00
(635.0)(406.4)
Air Filter
Air Filter
Section A-A
Legend
1. Controller
2. On/Off Switch
2
2
Air Filter
Air Filter
Mounting
Holes
0.438-Inch
Dia. Typ.
Section B-B
Notes:
3. 12-Inch Minimum Separation Between Enclosures
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-80

Transient-Free Power Factor Correction System
2.2
Contents
Description
Page
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Correction Units
Product Selection . . . . . . . . . . . . . . . . . . . . . . .
V3-T2-49
V3-T2-51
V3-T2-54
2
2
2
V3-T2-63
V3-T2-67
V3-T2-74
V3-T2-82
V3-T2-83
2
2
2
2
2
2
Transient-Free Static Switching Power Factor Correction Units

Product Description
Transient-free statically
switch capacitor units are
available in two models.
The FTE model is a real-time
transient-free system, used
to compensate extremely
rapid loads within one
cycle of operation (typically
520 msec).
The FTA model is a fast
transient-free system, used
to compensate any loads
within 34 seconds.
The FTA and FTE units
employ a fast or real-time
response, and include the
ability to switch larger steps
without creating significant
line noise. These relatively
maintenance-free units reside
in a smaller footprint and are
ideal for use in applications
such as flicker control, large
motor starting, bus voltage
stabilization, fault ridethrough solutions, power
factor correction and
many more.
Motor starting
On-site generation support
Spot welding
Wind turbines
Other dynamic loads
Three current transformers

with a 5 ampere secondary
are required to operate this
capacitor bank.
Rating based on Service
Entrance Ampacity. For other
ratios, please consult factory.

Enclosure
EMCEN50081-2,
EN50082-2, EN55011,
EN61000-4-2/3/4/5,
ENV50204, ENV50141
CE Mark73/23/EEC am.
93/68, 98/37/EC art. 4(2)
SafetyEN61010-1,
EN60439-1, EN60204
UL 508
CSA
2
2
2
2
2
2
2
2
Startup and
Commissioning by
factory trained personnel
is required for proper
operation and warranty
of this system
2
2
2
2
2
2
2
2
2
2
2
V3-T2-81
2.2

Product Selection
Transient-free reactive power compensation systems

The transient-free systems are custom engineered to order.
The Eaton transient-free

statically switched capacitor
systems represent the next
level of power system
enhancements by using
semi-conductor devices to
switch capacitors at the same
potential or zero potential
difference, thereby
eliminating the possible
problem of transients caused
by capacitor switching and
increasing the speed of
capacitive var compensation.
2
2
2
2
2
2
This level of performance is

needed when high-current
loads rapidly switch on and
off and require power factor,
voltage flicker, sag, or
harmonic improvement.
These disturbances can be
found in many industries,
including rockcrushing, arcwelding, plastic injection
molding, and crane
applications.
Please call Eatons Technical

Resource Center at 1-800809-2772, option #4,
suboption #2 to discuss your
application. See
TD02607012E for additional
technical information on
Eatons transient-free
reactive power compensation
systems. Pricing and
availability is available through
Eatons Technical Resource
Center. Please fill out the
following questionnaire
before requesting a
quotation.
2
2
Transient-Free Reactive Power Compensation Systems Questionnaire
Type of industry
(Automotive, alternative energy, lumber, etc.)
Type of application
(Welding, wind turbine, sawmill, etc.)
Project objectives
(PF correction, voltage control, reactive power

control, damping of power oscillations, unbalance
control, motor starting)
Amount of kvar required (if known)
kvar (300 to 3000 kvar)
2
2
2
2
2
2
Nominal system voltage
Nominal system frequency
Hz
Integral main breaker needed
(Yes/No)
Harmonic tuning order required (if known)
(2.67, 3.8, 4.5, or other)
Compensation time required (if known)
(34 seconds or 520 milliseconds)
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-82

2.2
Contents
HCU2 Active Harmonic Filters
Description
Page
UNIPUMP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UNIPAK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
HCU2 Harmonic Correction Unit
Catalog Number Selection . . . . . . . . . . . . . . .
Technical Data and Specifications . . . . . . . . . .
V3-T2-49
V3-T2-51
V3-T2-54
2
2
2
V3-T2-63
V3-T2-67
V3-T2-74
V3-T2-81
V3-T2-84
V3-T2-84
2
2
2
2
2

Product Description
Eatons HCU2 active

harmonic filters are
engineered to provide
dynamic harmonic correction
by actively injecting the
required currents into an
electrical distribution system
to cancel the entire spectrum
of harmonic currents at the
point of connection.
Typical applications include

locations with large amounts
of nonlinear loads including
6- and 12-pulse PWM
alternating current (AC)
variable frequency drives,
direct current (DC) drives, as
well as other switch-mode
power supply equipment.
This equipment can be found
in water and wastewater
treatment facilities, industrial
manufacturing and
warehousing plants, military
bases and commercial
locations.
HMI Home Screen Shot
Unlike passive filters, Eatons

HCU2 can provide effective
harmonic correction for
varying load conditions and
harmonic spectrums by
providing dynamic correction
up to their rated capacity. The
HCU2 also has the secondary
benefit of providing power
factor correction with any
excess capacity after
correcting all harmonic
conditions.
Features, Benefits
and Functions
Fast-acting harmonic
correction
NEMA 1, NEMA 2, NEMA
12, IP31, IP54 enclosures,
and chassis mount
versions available
60, 120, 200 and 300 A
units available (ampere
rating given at 380480 V)
Touchscreen human
machine interface (HMI)
Communications
connectivity
Designed for use in
environmentally controlled
conditions
Can be sized to meet
specific levels of harmonic
correction, providing
compliance with IEEE 519
recommended levels
Engineered to prevent
overloading
Scalable design can be
expanded without
impacting performance
Broad spectrum of
cancellation for robust
protection (2nd to 51st
harmonic)
Helps improve power
factor to maximize
efficiency
Easier and less expensive

installation than passive
filters, as active filter
design reduces the need
for detailed engineering
studies
HMI provides
comprehensive control
through icon-driven
interface
Improvements from HCUE to HCU2
Closed loop control: A

higher degree of harmonic
correction is available with
closed loop control than
open loop control
Reduced kW losses: Lower

kW losses result in lower
operating expenses and
reduced requirements for
equipment room HVAC
systems. The maximum
heat loss for a 300 A, 480 V
unit is 7.1 kW
Reduced footprint:
Wall-mounted 480 V
NEMA 1 units are
available in 60, 120, 200
and 300 A ratings
Ease of maintenance and

service: A standard USB
service port is provided for
firmware updates
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
UL/CSA approved
2
V3-T2-83
2.2

HCU2 060 D5 N2
2
2
Equipment Type
HCU2 = Harmonic correction unit
2
2
2
2
2
2
2
Ampere Rating
380480 V only
060 = 60 A
120 = 120 A
200 = 200 A
300 = 300 A
600 V only
047 = 47 A
094 = 94 A
157 = 157 A
235 = 235 A
690 V only
040 = 40 A
080 = 80 A
133 = 133 A
200 = 200 A
Voltage
D5 = 380480 V D7 = 3690 V
D6 = 600 V
IP00
N1
N2
N12
IP31
IP54
=
=
=
=
=
=
Enclosure Type
Chassis mount
NEMA 1 wall mount
NEMA 2 floor mount
NEMA 12 floor mount
IP31 floor mount
IP54 floor mount
Typical Uncorrected 6-Pulse Rectifier (Before) Current + HCU2 Injection Current = Corrected (After) Current
2
2
2
2
2
2
2
Recommended Placement
2
2
2
Source
Typical CT
Placement
Transformer
2
2
HCU
Load(s)
2
2
2
2
V3-T2-84

2.2
Eaton HCU2 Specifications

Specification
Description
Specification
Technical Specifications
Technical Specifications (Continued)
Standard rms output

current ratings
Communications capability
Modbus RTU, Modbus TCP/IP
Discrete input/outputs
4 input and 4 output dry contacts; assignable
Noise level (ISO3746)
<70 dB at 1 meter from unit surface
60 A, 120 A, 200 A, 300 A at 380 Vac to 480 Vac

47 A, 94 A, 157 A, 235 A at 600 Vac
40 A, 80 A, 133 A, 200 A at 690 Vac
Nominal frequency
50/60 Hz, 3 Hz auto sensing
Number of phases
3-phase
Description
2
2
Earthing (grounding) systems EMC filter ground switch for Isolated Terra, high resistance
Topology
Digital harmonic FFT Digital reactive power
Losses
To 480 Vac <3%; to 690 Vac <5%
Environmental Condition
0 C to 40 C
Relative humidity
095%, noncondensing
Seismic rating
Complies with IBC and ASCE7
Operating altitude
1000 m, (derate 1%/100 m above), maximum 4800 m
2
2
CT VA loading
1.0 VA (5 A CT secondary)
Spectrum cancellation
2nd to 51st, discrete; fully selectable per harmonic order

(amplitude and on/off)
Control basis
Closed loop (for new installations)

Open loop compatible for retrofit applications
Automatic rollback of output Occurs whenever heatsink temperature sensor exceeds

temperature limit
Harmonic attenuation
Closed loop: <3% THD(i); max. 20:1 THD(i) reduction with load
harmonic current above 50% of HCU2 rating
Open loop: <5% TDD
Requires 3% or higher inductive impedance per nonlinear load
Ambient temperature
protection
Absolute shutdown if air inlet temperature reaches 51 C
Preset output limits (rms)
Programmable set limit due to altitude or ambient

temperaturebecomes fixed output limit
Harmonic operational
features
% THDi set point

% THDv set point
Reference Standards
Harmonic avoidance
Output at specific harmonic order turned off if resonance or lack-of

impedance detected; or manually turned off
Parallel operation
Up to 10 units per set of CT (to 51st order), any size combination

Backward compatibility with Eaton HCUE operated in parallel
Contact Eaton for applications of more than 10 units
Parallel operation options
Master/master Master/slave
Multi-master/multi-slave
Same as Eaton HCUE for retrofits
Parallel sequence options
Lead/lag with unit rotation: one unit operates to full capacity

before next unit turns on; timed rotation Load share: All operating
units function at the same ouput percentage
2
2
2
2
Design
CE EMC Certification IEC/EN 60439-1, EN 61000-6-4 Class A,

EN 61000-6-2
Protection (enclosure)
IP00, IP20, IP31, IP54, NEMA 1, NEMA 2,

NEMA 12, UL Type Open (chassis mount)
Standards compliance/
certification
cULus (UL 508 , CSA 22.2 No. 14)

CE Certified, ABS, Lloyds, other local standards
2
2
2
Installation
Wall mount
Chassis mount (UL Type open) and NEMA 1 configurations
Free-standing
IP31, IP54, NEMA 2 and NEMA 12
Circuit protection
NEMA 1 and chassis mountexternal means required

Free-standing enclosuresincoming circuit breaker with
mechanical door interlock
Parallel HMI control
Any unit permits viewing and changing parameter settings of

complete system or any other unit in parallel system
Parallel communications
Proprietary COM bus between operating units
AIC rating
(input circuit breaker)
Optimized unity PF, leading (capacitive) or lagging (inductive) power

factor (Cos f) to target
To 415 Vac200 kA cULus; 125 kA IEC To 480 Vac200 kA

cULus; 75 kA IEC To 600 Vac100 kA cULus; 100 kA IEC
To 690 VacNo cULus; 100 kA IEC
Cable entry
Wall mount and chassis mountbottom only

Free-standingtop and bottom entry through gland plates
Control response time
25 s
Harmonic correction time
2 cycles
PCBA protection
Conformal coating on all PCBs Pollution Degree 2
Reactive correction time
1/4 cycle
Cooling configuration
Display
144 mm QVGA TFT 64k-color touchscreen
Display parameters
Hundreds of parameters are available. Examples include THDi,

THDv, oscilloscope for viewing many selected parameters, phasor
diagrams, load power, measured currents for Ih, Is, If, I neg seq, PF
(Cos f), injected currents for Ih, I reactive, I neg seq, etc.
Separate air plenums for heatsink section and PCBA section:

Heatsink (high heat plenum) input from bottom and exhaust
out top.
All components in high heat plenum rated IP54 or better no
filtering required
PCBA air supply must be clean and dry (filtering may be required)
No conductive particles permitted
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
V3-T2-85
2.2

Harmonic Correction Unit Ratings
Model
Voltage (V)
Frequency (Hz)
Total Current
Amperes (rms)
Watt Losses (kW)
HCU2060D5N1
380480
50/60
60
HCU2120D5N1
380480
50/60
120
HCU2200D5N1
380480
50/60
200
HCU2300D5N1
380480
50/60
300
7.1
Wall mount NEMA 1
UL/CSA
No
HCU2060D5IP00
380480
50/60
60
1.3
Chassis mount
UL/CSA
No
HCU2120D5IP00
380480
50/60
120
2.8
Chassis mount
UL/CSA
No
HCU2200D5IP00
380480
50/60
200
5.4
Chassis mount
UL/CSA
No
HCU2300D5IP00
380480
50/60
300
7.1
Chassis mount
UL/CSA
No
HCU2060D5IP31
380480
50/60
60
1.3
Floor mount IP31
CE
Yes
HCU2120D5IP31
380480
50/60
120
2.8
Floor mount IP31
CE
Yes
HCU2200D5IP31
380480
50/60
200
5.4
Floor mount IP31
CE
Yes
HCU2300D5IP31
380480
50/60
300
7.1
Floor mount IP31
CE
Yes
HCU2060D5N2
380480
50/60
60
1.3
Floor mount NEMA 2
UL/CSA
Yes
HCU2120D5N2
380480
50/60
120
2.8
Floor mount NEMA 2
UL/CSA
Yes
HCU2200D5N2
380480
50/60
200
5.4
Floor mount NEMA 2
UL/CSA
Yes
HCU2300D5N2
380480
50/60
300
7.1
Floor mount NEMA 2
UL/CSA
Yes
HCU2060D5N12
380480
50/60
60
1.3
Floor mount NEMA 12
UL/CSA
Yes
HCU2120D5N12
380480
50/60
120
2.8
Floor mount NEMA 12
UL/CSA
Yes
HCU2200D5N12
380480
50/60
200
5.4
Floor mount NEMA 12
UL/CSA
Yes
HCU2300D5N12
380480
50/60
300
7.1
Floor mount NEMA 12
UL/CSA
Yes
HCU2060D5IP54
380480
50/60
60
1.3
Floor mount IP54
CE
Yes
HCU2120D5IP54
380480
50/60
120
2.8
Floor mount IP54
CE
Yes
HCU2200D5IP54
380480
50/60
200
5.4
Floor mount IP54
CE
Yes
HCU2300D5IP54
380480
50/60
300
7.1
Floor mount IP54
CE
Yes
HCU2047D6IP31
600
50/60
47
1.8
Floor mount IP31
CE
Yes
HCU2094D6IP31
600
50/60
94
3.9
Floor mount IP31
CE
Yes
HCU2157D6IP31
600
50/60
157
7.2
Floor mount IP31
CE
Yes
HCU2235D6IP31
600
50/60
235
9.9
Floor mount IP31
CE
Yes
HCU2047D6N2
600
50/60
47
1.8
Floor mount NEMA 2
UL/CSA
Yes
HCU2094D6N2
600
50/60
94
3.9
Floor mount NEMA 2
UL/CSA
Yes
HCU2157D6N2
600
50/60
157
7.2
Floor mount NEMA 2
UL/CSA
Yes
HCU2235D6N2
600
50/60
235
9.9
Floor mount NEMA 2
UL/CSA
Yes
HCU2047D6IP54
600
50/60
47
1.8
Floor mount IP54
CE
Yes
HCU2094D6IP54
600
50/60
94
3.9
Floor mount IP54
CE
Yes
HCU2157D6IP54
600
50/60
157
7.2
Floor mount IP54
CE
Yes
HCU2235D6IP54
600
50/60
235
9.9
Floor mount IP54
CE
Yes
HCU2047D6N12
600
50/60
47
1.8
Floor mount NEMA 12
UL/CSA
Yes
HCU2094D6N12
600
50/60
94
3.9
Floor mount NEMA 12
UL/CSA
Yes
HCU2157D6N12
600
50/60
157
7.2
Floor mount NEMA 12
UL/CSA
Yes
2
2
2
2
HCU2 Enclosure Type
Version
Integral
Disconnect
1.3
Wall mount NEMA 1
UL/CSA
No
2.8
Wall mount NEMA 1
UL/CSA
No
5.4
Wall mount NEMA 1
UL/CSA
No
HCU2235D6N12
600
50/60
235
9.9
Floor mount NEMA 12
UL/CSA
Yes
HCU2040D7IP31
690
50/60
40
2.1
Floor mount IP31
CE
Yes
HCU2080D7IP31
690
50/60
80
4.5
Floor mount IP31
CE
Yes
HCU2133D7IP31
690
50/60
133
8.2
Floor mount IP31
CE
Yes
HCU2200D7IP31
690
50/60
200
11.4
Floor mount IP31
CE
Yes
HCU2040D7N2
690
50/60
40
2.1
Floor mount NEMA 2
UL/CSA
Yes
HCU2080D7N2
690
50/60
80
4.5
Floor mount NEMA 2
UL/CSA
Yes
HCU2133D7N2
690
50/60
133
8.2
Floor mount NEMA 2
UL/CSA
Yes
HCU2200D7N2
690
50/60
200
11.4
Floor mount NEMA 2
UL/CSA
Yes
HCU2040D7IP54
690
50/60
40
2.1
Floor mount IP54
CE
Yes
HCU2080D7IP54
690
50/60
80
4.5
Floor mount IP54
CE
Yes
HCU2133D7IP54
690
50/60
133
8.2
Floor mount IP54
CE
Yes
HCU2200D7IP54
690
50/60
200
11.4
Floor mount IP54
CE
Yes
HCU2040D7N12
690
50/60
40
2.1
Floor mount NEMA 12
UL/CSA
Yes
HCU2080D7N12
690
50/60
80
4.5
Floor mount NEMA 12
UL/CSA
Yes
HCU2133D7N12
690
50/60
133
8.2
Floor mount NEMA 12
UL/CSA
Yes
HCU2200D7N12
690
50/60
200
11.4
Floor mount NEMA 12
UL/CSA
Yes
V3-T2-86
2
2
2
2

Vol03 Tab02

Uploaded by

Document Informationclick to expand document informationVol03_Tab02

Document Informationclick to expand document information

Copyright:

Available Formats

Vol03 Tab02

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Vol03 Tab02

Uploaded by

Copyright:

Available Formats

SPD, Power Conditioning, PF Capacitors

and Harmonic Filters

Surge Protection and Power Conditioning

Power Factor Correction and Harmonic Filtering

Volume 3Power Distribution and Control Assemblies CA08100004EAugust 2016 www.eaton.com

SPD, Power Conditioning, PF Capacitors and Harmonic Filters

Industrial and Commercial Surge Protection

Industrial and Commercial Surge Protection

SPD Series for Integration

SPD Series Sidemount Units

Critical Load Protection

SPD Series Integrated Units

SPD Series Sidemount Unit

Commercial and Light

SPD Series Integrated Unit

Volume 3Power Distribution and Control Assemblies CA08100004EAugust 2016 www.eaton.com

SPD, Power Conditioning, PF Capacitors and Harmonic Filters

Surge Protection for Sub-Panel and OEM Applications

Panelboards with Integrated

Available in standard and

120/240 Vac, singlephase, three-wire

208Y/120 Vac, threephase, four-wire

480Y/277 Vac, threephase, four-wire

600Y/347 Vac, threephase, four-wire (other

Sag Ride-Through (SRT2)

Facility-Wide Power Protection Solutions

The most accepted design methodology is based on two concepts:

2. Surge protection should be installed

Volume 3Power Distribution and Control Assemblies CA08100004EAugust 2016 www.eaton.com

SPD, Power Conditioning, PF Capacitors and Harmonic Filters

Application Recommendations for Surge Products

Eatons Surge Product

Features and Competitive Advantages

SPD Series integrated units

Ideal package for any commercial facility

SPD Series sidemount units

Cost-effective, reliable protection using the SPD Series or SPC units

SPD Series integrated units in panelboards, switchboards,

Able to meet competitors surge protection specifications

SPD Series sidemount units

Wall space savings by using integrated SPD Series units

SPD MAX units

Quick-ship capabilities from Eaton assembly satellites and service centers

AEGIS units for critical load applications

Power conditioning capability for a wide variety of applications

Power conditioners (EVR and SRT2 units)

Increased surge protection performance by using integrated SPD Series units

SPD Series integrated units in panelboards, switchboards,

Increased surge protection performance by using integrated SPD Series units

Small and large facilities

SPD Series sidemount units

SPD MAX units

AEGIS products protect expensive critical loads from harmful damage

AEGIS units for critical load applications such as PLCs,

EVR units correct voltage regulation problems

Power conditioners (EVR and SRT2 units)

Wall space savings by using integrated SPD Series units