Asme Ix Quiz

The purpose of the WPS and PQR is to determine that:
the weldment has the desired properties
The WPS list :

all of the above
The PQR must list

essential variables and supplementary essential when notch toughness is required
What is the earliest Edition of Section IX recognized by the current edition ?

1962
New Welding Procedure Specifications must meet the ________Edition and addenda
of Section IX
current (latest mandatory)
Each _______ shall conduct the tests required by Section IX to quality the WPS's used
during the construction,alteration, or repair .
Manufacturer or contractor
The records of procedure,welder and welding operator qualification must be

available to the ________.
Authorized Inspector
A welder qualifying with a groove weld in plate in the 4G position is qualified to weld
groove welds in plate and pipe over 24" O.D. in the _______ positions.
Flat & overhead
A welder qualifying with plate groove welds in the 3G and 4G positions is qualified
to weld groove welds in plate in the _______ positions.
Flat , vertical and overhead

A welder qualifying by making a groove weld on pipe with an O.D. of 3/4" in the 5G
position is qualified to weld groove welds in :
6" O.D. Pipe in the vertical postion
In general, qualification on groove welds also qualifies a welder to make:

Fillet welds
Charpy V- notch tests are performed to determine a weldment's

Notch toughness
A welder making a groove weld using the SAW process on P1 materials may be
qualified using radiography.
True
When a tensile specimen breaks in the base metal outside of the weld or fushion
line, the strength recorded may be _______ below the specified tensile and be
accepted.
all of the above
Guided-bend specimens shall have no open defects in the weld or heat effected
zone exceeding _______ measured in any direction on the convex surface of the
specimen after bending.
1/8"
When using radiographs to qualify welders, the acceptance standards used are
found in:
ASME Section IX
A WPS must describe:

All of the above
A PQR must describe:

Essential variables
The _______must certify the PQR as accurate.

manufacturer or contractor
For the SMAW process ______is an essential variable for the WPS.
Post Weld heat treatment (PWHT)
For the SAW process ______is an essential variable for the WPS.
Supplement powdered filler metal(if used)
The basic purpose of testing a welder is to establish the welder's ________

Ability to deposit sound weld metal
The record of a welder's performance test is called a _______

WPQ
IF A welder qualified with the manual SMAW process on jan.1,1997 and last welded
with manual SMAW on March 15,1997 , would he still be qualified on OCT0BER
7,1997?
no
A welder qualifying with SMAW process with a double welded groove weld is
qualified to weld .
with backing only
Immediate retests of welders qualifications coupons

shall use the same volumetric test method
Welder performance qualification records must describe all the _________ variables
specified..
Essential
A welder depositing 1/2" of weld metal in three layers in a groove weld with the
SMAW process is qualified to deposit up to ______ of weld metal.
Max to be welded
"P" numbers are used to designate groups of

base metals
A welder qualifying with P-No.21 is qualified to weld

P-21 - P-26 to P-21 - P-26
Section IX groups welding electrodes by

"F" number
Ferrous weld metal chemical composition may be designated using

"A" number
For welder qualification with the SMAW process _______ is an essential variable .
P- number
Each welder must be assigned a (n)

Unique identifer
A welder qualification coupon welded in the 2G position of 5/16 " thick plate
material must have how many root and face bends?
2 total - 1 each
A WPS shall have :
the PQR referenced
Welding in the 1G position qualifies a welder in what position?

flat
Which of the following is an essential variable for qualification of an SMAW welding

procedure??
"F" number
If a welder is to be qualified by RT or NDE (volumetric inspection) ,then:

the first 6" of the first production weld is radiographed for the processes & mode
allowed.
A welder may be qualified using volumetric inspection in certain processes except

for _______
GMAW (short-circuiting mode)
A tank is being built to API 650 of a A516-Gr. 55 shell material that is 1.125" thick.
what preheat will be required??bonus question
32F

Asme Ix Quiz

Uploaded by

Copyright:

Available Formats

Asme Ix Quiz

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Asme Ix Quiz

Uploaded by

Copyright:

Available Formats

The purpose of the WPS and PQR is to determine that:

the weldment has the desired properties

The WPS list :

The PQR must list

What is the earliest Edition of Section IX recognized by the current edition ?

The records of procedure,welder and welding operator qualification must be

In general, qualification on groove welds also qualifies a welder to make:

Charpy V- notch tests are performed to determine a weldment's

A WPS must describe:

A PQR must describe:

The _______must certify the PQR as accurate.

The basic purpose of testing a welder is to establish the welder's ________

The record of a welder's performance test is called a _______

Immediate retests of welders qualifications coupons

"P" numbers are used to designate groups of

A welder qualifying with P-No.21 is qualified to weld

Section IX groups welding electrodes by

Ferrous weld metal chemical composition may be designated using

Each welder must be assigned a (n)

A WPS shall have :

the PQR referenced

Welding in the 1G position qualifies a welder in what position?

Which of the following is an essential variable for qualification of an SMAW welding

If a welder is to be qualified by RT or NDE (volumetric inspection) ,then:

A welder may be qualified using volumetric inspection in certain processes except

You might also like