Ilm College of Engineering & Technology: Model Exam - Novenber-2015

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 2

ILM COLLEGE OF ENGINEERING & TECHNOLOGY

(Approved by AICTE and affiliated to MG University)


TECHNO VILLAGE; METHALA, KEEZHILLAM P.O., PERUMBAVOOR

MODEL EXAM - NOVENBER-2015


Subject: AN 010 306 BASIC STRENGTH OF MATERIALS
Max.Marks- 100
Sem / Branch: S3 / Aero
Time: 3 Hrs.
Faculty
Date: 12/11/2015

: Deepak D

Part A (Answer all questions- 3 Marks each)


1)
2)
3)
4)
5)

Define bulk modulus.


When will be the bending moment maximum?
What is section modulus?
What are the assumptions made in torsion equation?
Define the terms column and strut.

Part B (Answer all questions- 5 Marks each)


6) Relation between E & K?
7) Draw Shearing force and bending moment diagram for a simply
Cantilever beam with a Uniformly Distributed Load.
8) Show that the Solid circular section, the maximum shear stress is 4/3
times the mean (average) stress.
9) A hollow circular shaft 20mm thick transmits 294kW at 200rpm.
Determine the diameters of the shaft if shear strain due to torsion is not
exceed 8.6x10-4. Take modulus of rigidity as 80GN/m2.
10)
Derive Rankines formula for intermediate columns.

Part-C (Answer all questions. 12 marks each)

11)
a) A flat 300mm long, 30mmX50mm uniform cross section is acted
upon by the following forces uniformly distributed over the respective
cross section. 20kN in the direction of length (tensile): 350kN in the
direction of the width (compressive) and 200kN in the direction of
thickness (tensile). Determine the change in volume of the flat. Take
E=140GN/m2, m=4.
OR
b) A steel bar is placed between two copper bars each having same area
and same length as the steel bar at 15C and rigidly connected at ends.
When the temperature rise by 300C, the length of the compound bars
increased by 1.5mm. Determine the original length and final stresses in
each bar. Es=200GPa, Ec=100GPa, S=12x10-6/C, C=17.5x10-6/C.

12)
a) Draw the shear force and bending moment diagram for a simply
supported beam of length 9m and carrying a uniformly distributed load of
10kN/m for a distance of 6m from the left end. Also calculate the
maximum Bending moment on the section.
OR
b) Draw the S.F and B.M diagrams for the overhanging beam of 6m length
carrying uniformly distributed load of 2kN/m over the entire length and a
point load of 2kN at right end. One support at left end and another
support at 4m from left end. Locate the point of contraflexure.
13)
a) A cast iron beam is of I-section with web 20mmX200mm, Top
flange 80mmX20mm, bottom flange 160mmX40mm which symmetric
about Y-axis. The beam is simply supported on a span of 5m. If the tensile
stress is not exceed 20N/mm2 find the safe uniformly load which the
beam can carry. Find also the maximum compressive stress.

OR
b) A beam with a span of 4.5m carries a point load of 30kN at 3m from
the left support. If for the section Ixx=54.97x10-6m4 and E=200GN/m2.
Find i) The deflection under the load and ii) The position and moment of
maximum deflection.
14)
a) A solid steel shaft is subjected to torque of 45kNm. If the angle of
twist is 0.5 per metre length of the shaft and the shear stress is not to be
allowed to exceed 90MN/m2. Find i) Suitable diameter of the shaft. ii)
Maximum shear stress and angle of twist and iii) Maximum shear strain in
the shaft. Take C=80GN/m2.

OR

b) A built up cylindrical shell of 300mm diameter, 3m long and 6m thick is


subjected to an internal pressure of 2MN/m 2. Calculate the change in
length, diameter and volume of the cylinder under that pressure if the
efficiencies of the longitudinal and circumferential joints are 80% and
50% respectively. E=200GN/m2, m=3.5.
15)
a) An element in a stressed material has tensile stress of 500MN/m 2
and a compressive stress of 350MN/m2 acting on two mutually
perpendicular planes and equal shear stresses of 100MN/m 2 on these
planes. Find principal stresses and position of the principal planes. Find
also maximum shearing stress.
OR
b) A slender pin ended aluminium column 1.8m long and circular cross
section is to have an outside diameter of 50mm. Calculate the necessary
internal diameter to prevent failure by buckling if the actual load applied
is 13.6kN and the critical load applied is twice the actual load.
EAL=70GN/m2.

*End of Question Paper*

You might also like