Inspection Checklist Masonry Wall

City of Santa Monica
Building and Safety Division

Masonry Wall Checklist
This is to be used as a general checklist; it is not inclusive

of all code requirements and inspection criteria.
Per California Building Code (CBC) Chapters 1, 17, 18, 21
American Concrete Institute (ACI) 530.1 (masonry) and 318 (concrete)
And applicable ASTM referenced standards
FOOTING INSPECTION
Approved plans on site CBC 2101.3
Location per approved plans CBC 107
Slope setback maintained 5 to daylight CBC 1808.7
Clean of foreign debris ACI 318 7.5.1(d)
Size per approved plans: depth and width, key way if required.
Stepped, if slope exceeds 1/10. CBC 1809.3
Reinforcing steel per CBC 1907 and ACI 318
o Minimum grade per plans (mill certification required for foreign rebar )
o Properly sized and placement per plan ACI 318 7.5.1
o Minimum clearances to earth maintained. 3 per ACI 318
o Adequately secure from displacement ACI 318 7.5.1
o Lap splice requirements maintained. Length, staggered splices, etc.
o Minimum length of lap splices (30db in concrete, 40/48 db. in masonry)
o Location, type, and installation of mechanical splices (manufacturers data required)
o Location, type of welded splices (certified welder required/deputy inspection and
materials identification required per CBC 1704.3.1.3 and 1708.2)
o Double dowels at jambs, wall ends and corners as required by plans and ACI 530
Plumbing piping and electrical conduits Per ACI 318 6.3 and SEOR (structural.
Engineer).
If pipes or conduits run through stem/masonry wall then:
o Sleeved with schedule 40 steel
o Protect from concrete
o 3 diameter on center
o Clearances to reinforcement minimum
Structural Observation per plan and CBC 1710
Soils engineer approval per plan and CBC 1803.5.11
Revised 2011
Page 1 of 3

MASONRY (LAYUP) Materials per ACI 530 and ASTM standards Execution per ACI 530.1
Rebar and footing clean of over pour and laitance per ACI 530.1 3.2
Type of masonry per approved plans (density). No blemished, cracked or broken units
per ASTM standard C 90
Deputy inspection requirements of materials and layup-periodic for Level 1
Strength testing (prisms) per CBC 1704.5 for Level 2
Wall height per approved plans
Head and bed joints solidly mortar filled, except beveled end of open-end units.
Initial bed joint >< . ACI 530.1 3.3B.1
Bed and head joints 3/8 thick +/- 1/8 ACI 350.1 3.3.B
o Max mortar fin projection of . ACI 530.1 3.3B.1c
o Clean of foreign debris and mortar droppings per ACI 530.1
Clean-outs required for grout pours >5 ACI 530.1 3.2F
o At all cells with vertical reinforcing bars
o 3 minimum dimension ACI 530 3.2F.2
o Max 32 O.C. if solidly grouted
o Max 48 if partially grouted
Max grout pour height per ACI 530 3.5 and table 7 (based on cell size/grout space)
Anchor bolts > minimum grout surrounding per ACI 530 3.4D
Plumb and line of masonry layup- within 1/4 in 10 ( max.) per ACI 530 3.3F
REINFORCING STEEL (in masonry wall) per ACI 530.1
Minimum grade per plan ( mill cert required )
Properly sized per plans (special requirements for shear walls)
o Maximum size #11 (36mm)
o Minimum #4 at 2 o.c. each way in Seismic Design Category D
Maximum reinforcement 6% of cell area without splice or 12% of cell area with splice
Placed per plans and within tolerances (vertical rebar within sideways, 2 long way)
Adequately secured from displacement ACI 530.1 3.4B.1 and 3.2E (no drop in bars)
Lentil bars minimum 2 past openings each side ACI 530 1.17.3.2.3.1
Double jamb bars at openings
Vertical steel within 16 of wall openings >16 and corners. Within 8 of joints and end
of wall ACI 530 1.17.3.2.3.1
Dowels embedded in concrete not bent more than 1 in 6. ACI 530.1 3.4B.8.6
Minimum 40 db (40 bar diameters) lap slice, 48db for grade 60 rebar (typical)
Minimum clearance to masonry maintained. ACI 530.1 3.4B
o for fine grout for course grout.
Revised 2011
Page 2 of 3

PRE-GROUT INSPECTION
All grout per ASTM C476, 8-10 slump, mix design and psi per SEOR (structural
engineer of record)
Grout consolidation and reconsolidation per ACI 530.5E
Maximum pour height per Approved plans and ACI 530
Maximum lift height per ACI 530 3.5D
Periodic deputy inspection of reinforcement (and materials) per CBC1704.5.1
Special inspection requirements apply to all masonry per CBC 1704.5.1(all
grouting requires continuous deputy inspection and periodic inspection of
reinforcement)
Deputy(s) registered with the City of Santa Monica (S.M.M.C.)
Verify permit description reflects actual work being performed.
Minimum grout key of 1 per ACI 530 3.5F
Bed and head joints 3/8+/- 1/8 and initial bed joints min.and 3/4 max. per ACI
Hot/cold weather precaution requirements in place per CBC 21
FINAL INSPECTION
Wall construction complete, wall capped
Appropriate curing time for retaining wall prior to backfill (28 days typical)
Wall height and length per approved plans
All grout lifts signed off, all city agencies approved
Final deputy inspectors report per CBC 1704
Wall passes the visual acceptance criteria of ACI 530
Smoke alarms per CBC 907
Carbon Monoxide detectors per CBC 420
Seismic gas shutoff valve if permit valuation is over $10,000
Revised 2011
Page 3 of 3

Inspection Checklist Masonry Wall

Uploaded by

Copyright:

Available Formats

Inspection Checklist Masonry Wall

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Inspection Checklist Masonry Wall

Uploaded by

Copyright:

Available Formats

What are the main steps involved in constructing a masonry wall?

What inspections are required during the construction of a masonry wall?

City of Santa Monica

Building and Safety Division

This is to be used as a general checklist; it is not inclusive

City of Santa Monica

City of Santa Monica

You might also like