1. Refer to the exhibit.

A network administrator is configuring a

router as a DHCPv6 server. The administrator issues a show ipv6
dhcp pool command to verify the configuration. Which statement
explains the reason that the number of active clients is 0?

The default gateway address is not provided in the pool.

No clients have communicated with the DHCPv6 server yet.
The IPv6 DHCP pool configuration has no IPv6 address range specified.
The state is not maintained by the DHCPv6 server under stateless DHCPv6
operation.*

2. Which command, when issued in the interface configuration

mode of a router, enables the interface to acquire an IPv4 address
automatically from an ISP, when that link to the ISP is enabled?
ip dhcp pool
ip address dhcp*
service dhcp

ip helper-address

3. Which kind of message is sent by a DHCP client when its IP

address lease has expired?
a DHCPDISCOVER broadcast message
a DHCPREQUEST broadcast message
a DHCPREQUEST unicast message*
a DHCPDISCOVER unicast message

4. Refer to the exhibit. R1 has been configured as shown. However,

PC1 is not able to receive an IPv4 address. What is the problem?

A DHCP server must be installed on the same LAN as the host that is receiving the IP
address.
R1 is not configured as a DHCPv4 server.
The ip address dhcp command was not issued on the interface Gi0/1.

The ip helper-address command was applied on the wrong interface.*

5. A college marketing department has a networked storage device

that uses the IP address 10.18.7.5, TCP port 443 for encryption, and
UDP port 4365 for video streaming. The college already uses PAT
on the router that connects to the Internet. The router interface has
the public IP address of 209.165.200.225/30. The IP NAT pool
currently uses the IP addresses ranging from 209.165.200.228-236.
Which configuration would the network administrator add to allow
this device to be accessed by the marketing personnel from home?
ip nat pool mktv 10.18.7.5 10.18.7.5
ip nat outside source static 10.18.7.5 209.165.200.225
ip nat inside source static tcp 10.18.7.5 443 209.165.200.225 443
ip nat inside source static udp 10.18.7.5 4365 209.165.200.225 4365**
ip nat inside source static tcp 209.165.200.225 443 10.18.7.5 443
ip nat inside source static udp 209.165.200.225 4365 10.18.7.5 4365
No additional configuration is necessary.

6. What is a disadvantage of NAT?

There is no end-to-end addressing.*
The router does not need to alter the checksum of the IPv4 packets.
The internal hosts have to use a single public IPv4 address for external communication.
The costs of readdressing hosts can be significant for a publicly addressed network.

7. Which type of traffic would most likely have problems when

passing through a NAT device?
Telnet

IPsec*
HTTP
ICMP
DNS

8. What benefit does NAT64 provide?

It allows sites to use private IPv6 addresses and translates them to global IPv6 addresses.
It allows sites to connect multiple IPv4 hosts to the Internet via the use of a single public
IPv4 address.
It allows sites to connect IPv6 hosts to an IPv4 network by translating the IPv6
addresses to IPv4 addresses.*
It allows sites to use private IPv4 addresses, and thus hides the internal addressing
structure from hosts on public IPv4 networks.

9. Refer to the exhibit. The Gigabit interfaces on both routers have

been configured with subinterface numbers that match the VLAN
numbers connected to them. PCs on VLAN 10 should be able to
print to the P1 printer on VLAN 12. PCs on VLAN 20 should print to
the printers on VLAN 22. What interface and in what direction
should you place a standard ACL that allows printing to P1 from
data VLAN 10, but stops the PCs on VLAN 20 from using the P1
printer? (Choose two.)

R1 Gi0/1.12*
R1 S0/0/0
R2 S0/0/1
R2 Gi0/1.20
inbound
outbound*

10. Which two packet filters could a network administrator use on

an IPv4 extended ACL? (Choose two.)
destination MAC address
ICMP message type*
computer type
source TCP hello address
destination UDP port number*

11. A network administrator is explaining to a junior colleague the

use of the lt and gt keywords when filtering packets using an
extended ACL. Where would the lt or gt keywords be used?
in an IPv6 extended ACL that stops packets going to one specific destination VLAN
in an IPv4 named standard ACL that has specific UDP protocols that are allowed to be used
on a specific server
in an IPv6 named ACL that permits FTP traffic from one particular LAN getting to another
LAN
in an IPv4 extended ACL that allows packets from a range of TCP ports destined for a
specific network device*

12. Which three values or sets of values are included when creating
an extended access control list entry? (Choose three.)
access list number between 1 and 99
access list number between 100 and 199*
default gateway address and wildcard mask
destination address and wildcard mask*
source address and wildcard mask*
source subnet mask and wildcard mask
destination subnet mask and wildcard mask

13. A network administrator is designing an ACL. The networks

192.168.1.0/25, 192.168.0.0/25, 192.168.0.128/25, 192.168.1.128/26,
and 192.168.1.192/26 are affected by the ACL. Which wildcard mask,
if any, is the most efficient to use when specifying all of these
networks in a single ACL permit entry?

0.0.0.127
0.0.0.255
0.0.1.255*
0.0.255.255
A single ACL command and wildcard mask should not be used to specify these particular
networks or other traffic will be permitted or denied and present a security risk.

14. The computers used by the network administrators for a school

are on the 10.7.0.0/27 network. Which two commands are needed at
a minimum to apply an ACL that will ensure that only devices that
are used by the network administrators will be allowed Telnet
access to the routers? (Choose two.)
access-class 5 in*
access-list 5 deny any
access-list standard VTY
permit 10.7.0.0 0.0.0.127
access-list 5 permit 10.7.0.0 0.0.0.31*
ip access-group 5 out
ip access-group 5 in

15. A network administrator is adding ACLs to a new IPv6

multirouter environment. Which IPv6 ACE is automatically added
implicitly at the end of an ACL so that two adjacent routers can
discover each other?
permit ip any any
permit ip any host ip_address

permit icmp any any nd-na*

deny ip any any

16. Which statement describes a route that has been learned

dynamically?
It is automatically updated and maintained by routing protocols.*
It is unaffected by changes in the topology of the network.
It has an administrative distance of 1.
It is identified by the prefix C in the routing table.

17. Refer to the exhibit. How did the router obtain the last route that
is shown?

The ip route command was used.

The ipv6 route command was used.
Another router in the same organization provided the default route by using a
dynamic routing protocol.*
The ip address interface configuration mode command was used in addition to the network
routing protocol configuration mode command.

18. Which statement is correct about IPv6 routing?

IPv6 routing is enabled by default on Cisco routers.
IPv6 only supports the OSPF and EIGRP routing protocols.

IPv6 routes appear in the same routing table as IPv4 routes.

IPv6 uses the link-local address of neighbors as the next-hop address for dynamic
routes.*

19. Refer to the exhibit. Which type of route is 172.16.0.0/16?

child route
ultimate route
default route
level 1 parent route*

20. Which two factors are important when deciding which interior
gateway routing protocol to use? (Choose two.)
scalability*
ISP selection
speed of convergence*
the autonomous system that is used
campus backbone architecture

21. Refer to the exhibit. Which type of IPv6 static route is

configured in the exhibit?

directly attached static route

recursive static route*

fully specified static route
floating static route

22. A router has used the OSPF protocol to learn a route to the
172.16.32.0/19 network. Which command will implement a backup
floating static route to this network?
ip route 172.16.0.0 255.255.240.0 S0/0/0 200
ip route 172.16.32.0 255.255.224.0 S0/0/0 200*
ip route 172.16.0.0 255.255.224.0 S0/0/0 100
ip route 172.16.32.0 255.255.0.0 S0/0/0 100

23. Which summary IPv6 static route statement can be configured

to summarize only the routes to networks 2001:db8:cafe::/58
through 2001:db8:cafe:c0::/58?
ipv6 route 2001:db8:cafe::/62 S0/0/0
ipv6 route 2001:db8:cafe::/54 S0/0/0
ipv6 route 2001:db8:cafe::/56 S0/0/0*
ipv6 route 2001:db8:cafe::/60 S0/0/0

24. Refer to the exhibit. If RIPng is enabled, how many hops away
does R1 consider the 2001:0DB8:ACAD:1::/64 network to be?

1
2

3*
4

25. Which statement is true about the difference between OSPFv2

and OSPFv3?
OSPFv3 routers use a different metric than OSPFv2 routers use.
OSPFv3 routers use a 128 bit router ID instead of a 32 bit ID.
OSPFv3 routers do not need to elect a DR on multiaccess segments.
OSPFv3 routers do not need to have matching subnets to form neighbor
adjacencies.*

26. What happens immediately after two OSPF routers have

exchanged hello packets and have formed a neighbor adjacency?
They exchange DBD packets in order to advertise parameters such as hello and dead
intervals.
They negotiate the election process if they are on a multiaccess network.
They request more information about their databases.
They exchange abbreviated lists of their LSDBs.*

27. What does the cost of an OSPF link indicate?

A higher cost for an OSPF link indicates a faster path to the destination.
Link cost indicates a proportion of the accumulated value of the route to the destination.
Cost equals bandwidth.
A lower cost indicates a better path to the destination than a higher cost does.*

28. Which three pieces of information does a link-state routing

protocol use initially as link-state information for locally connected
links? (Choose three.)
the link router interface IP address and subnet mask*
the type of network link*
the link next-hop IP address
the link bandwidth
the cost of that link*

29. Which three requirements are necessary for two OSPFv2

routers to form an adjacency? (Choose three.)
The two routers must include the inter-router link network in an OSPFv2 network
command.*
The OSPFv2 process is enabled on the interface by entering the ospf process area-id
command.
The OSPF hello or dead timers on each router must match.*
The OSPFv2 process ID must be the same on each router.
The link interface subnet masks must match.*
The link interface on each router must be configured with a link-local address.

30. A router needs to be configured to route within OSPF area 0.

Which two commands are required to accomplish this? (Choose
two.)
RouterA(config)# router ospf 0
RouterA(config)# router ospf 1*
RouterA(config-router)# network 192.168.2.0 0.0.0.255 0

RouterA(config-router)# network 192.168.2.0 0.0.0.255 area 0*

RouterA(config-router)# network 192.168.2.0 255.255.255.0 0

31. What are two features of a link-state routing protocol? (Choose

two.)
Routers send periodic updates only to neighboring routers.
Routers send triggered updates in response to a change.*
Routers create a topology of the network by using information from other routers.*
The database information for each router is obtained from the same source.
Paths are chosen based on the lowest number of hops to the designated router.

32. Why would an administrator use a network security auditing

tool to flood the switch MAC address table with fictitious MAC
addresses?
to determine which ports are not correctly configured to prevent MAC address
flooding*
to determine when the CAM table size needs to be increased in order to prevent overflows
to determine if the switch is forwarding the broadcast traffic correctly
to determine which ports are functioning

33. Two employees in the Sales department work different shifts

with their laptop computers and share the same Ethernet port in the
office. Which set of commands would allow only these two laptops
to use the Ethernet port and create violation log entry without
shutting down the port if a violation occurs?

switchport mode access

switchport port-security
switchport mode access
switchport port-security
switchport port-security maximum 2
switchport port-security mac-address sticky
switchport port-security violation restrict**
switchport mode access
switchport port-security maximum 2
switchport port-security mac-address sticky
switchport mode access
switchport port-security maximum 2
switchport port-security mac-address sticky
switchport port-security violation protect

34. Which problem is evident if the show ip interface command

shows that the interface is down and the line protocol is down?
An encapsulation mismatch has occurred.
A cable has not been attached to the port.*
The no shutdown command has not been issued on the interface.
There is an IP address conflict with the configured address on the interface.

35. What caused the following error message to appear?01:11:12:

%PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/8,
putting Fa0/8 in err-disable state
01:11:12: %PORT_SECURITY-2-PSECURE_VIOLATION: Security
violation occurred, caused by MAC address 0011.a0d4.12a0 on port
FastEthernet0/8.

01:11:13: %LINEPROTO-5-UPDOWN: Line protocol on Interface

FastEthernet0/8, changed state to down
01:11:14: %LINK-3-UPDOWN: Interface FastEthernet0/8, changed
state to down
Another switch was connected to this switch port with the wrong cable.
An unauthorized user tried to telnet to the switch through switch port Fa0/8.
NAT was enabled on a router, and a private IP address arrived on switch port Fa0/8.
A host with an invalid IP address was connected to a switch port that was previously
unused.
Port security was enabled on the switch port, and an unauthorized connection was
made on switch port Fa0/8.*

36. While analyzing log files, a network administrator notices

reoccurring native VLAN mismatches. What is the effect of these
reoccurring errors?
All traffic on the error-occurring trunk port is being misdirected or dropped.
The control and management traffic on the error-occurring trunk port is being
misdirected or dropped.*
All traffic on the error-occurring trunk port is being switched correctly regardless of the error.
Unexpected traffic on the error-occurring trunk port is being received.

37. Which three pairs of trunking modes will establish a functional

trunk link between two Cisco switches? (Choose three.)
dynamic desirable dynamic desirable*
dynamic auto dynamic auto
dynamic desirable dynamic auto*

dynamic desirable trunk*

access trunk
access dynamic auto

38. What are two ways of turning off DTP on a trunk link between
switches? (Choose two.)
Change the native VLAN on both ports.
Configure attached switch ports with the dynamic desirable command option.
Configure attached switch ports with the nonegotiate command option.*
Configure one port with the dynamic auto command option and the opposite attached
switch port with the dynamic desirable command option.
Place the two attached switch ports in access mode.*

39. A network administrator is using the router-on-a-stick method to

configure inter-VLAN routing. Switch port Gi1/1 is used to connect
to the router. Which command should be entered to prepare this
port for the task?
Switch(config)# interface gigabitethernet 1/1
Switch(config-if)# spanning-tree vlan 1
Switch(config)# interface gigabitethernet 1/1
Switch(config-if)# spanning-tree portfast
Switch(config)# interface gigabitethernet 1/1
Switch(config-if)# switchport mode trunk**
Switch(config)# interface gigabitethernet 1/1
Switch(config-if)# switchport access vlan 1

40. Which two characteristics describe the native VLAN? (Choose

two.)
Designed to carry traffic that is generated by users, this type of VLAN is also known as the
default VLAN.
The native VLAN traffic will be untagged across the trunk link.*
This VLAN is necessary for remote management of a switch.
High priority traffic, such as voice traffic, uses the native VLAN.
The native VLAN provides a common identifier to both ends of a trunk.*

41. On a switch that is configured with multiple VLANs, which

command will remove only VLAN 100 from the switch?
Switch# delete flash:vlan.dat
Switch(config-if)# no switchport access vlan 100
Switch(config-if)# no switchport trunk allowed vlan 100
Switch(config)# no vlan 100*

42. What is the purpose of setting the native VLAN separate from
data VLANs?
The native VLAN is for carrying VLAN management traffic only.
The security of management frames that are carried in the native VLAN can be enhanced.
A separate VLAN should be used to carry uncommon untagged frames to avoid
bandwidth contention on data VLANs.*
The native VLAN is for routers and switches to exchange their management information, so
it should be different from data VLANs.

43. A network contains multiple VLANs spanning multiple switches.

What happens when a device in VLAN 20 sends a broadcast
Ethernet frame?
All devices in all VLANs see the frame.
Devices in VLAN 20 and the management VLAN see the frame.
Only devices in VLAN 20 see the frame.*
Only devices that are connected to the local switch see the frame.

44. Refer to the exhibit. The partial configuration that is shown was
used to configure router on a stick for VLANS 10, 30, and 50.
However, testing shows that there are some connectivity problems
between the VLANs. Which configuration error is causing this
problem?

A configuration for the native VLAN is missing.

There is no IP address configured for the FastEthernet 0/0 interface.
The wrong VLAN has been configured on subinterface Fa0/0.50.*

The VLAN IP addresses should belong to the same subnet.

45. What is the purpose of an access list that is created as part of

configuring IP address translation?
The access list defines the valid public addresses for the NAT or PAT pool.
The access list defines the private IP addresses that are to be translated.*
The access list prevents external devices from being a part of the address translation.
The access list permits or denies specific addresses from entering the device doing the
translation.

46. Which command will create a static route on R2 in order to

reach PC B?

R2(config)# ip route 172.16.2.1 255.255.255.0 172.16.3.1

R2(config)# ip route 172.16.2.0 255.255.255.0 172.16.2.254

R2(config)# ip route 172.16.2.0 255.255.255.0 172.16.3.1*

R2(config)# ip route 172.16.3.0 255.255.255.0 172.16.2.254

47. Fill in the blank.

In IPv6, all routes are level __1__ ultimate routes.
48. Fill in the blank.
Static routes are configured by the use of the __ip route__ global
configuration command.
49. Fill in the blank.
The OSPF Type 1 packet is the __Hello__ packet.
50. Fill in the blank.
The default administrative distance for a static route is __1__ .
51. Match the order in which the link-state routing process occurs
on a router. (Not all options are used.)
Each router is responsible for saying hello to its neighbors on directly connected networks.
> step 2
Each router builds a Link-State Packet (LSP) containing the state of each directly connected
link > step 3
Each router learns about its own directly connected networks. > step 1
Each router increments the hop count for the destination network. -> NOT SCORED
Each router floods the LSP to all neighbors, who then store all LSPs received in a database
> step 4

Each router uses the database to construct a complete map of the topology and computes
the best > step 5

52. Which information does a switch use to populate the MAC

address table?
the destination MAC address and the incoming port
the destination MAC address and the outgoing port
the source and destination MAC addresses and the incoming port
the source and destination MAC addresses and the outgoing port
the source MAC address and the incoming port*
the source MAC address and the outgoing port

53. Refer to the exhibit. How many broadcast and collision domains
exist in the topology?

10 broadcast domains and 5 collision domains

5 broadcast domains and 10 collision domains*

5 broadcast domains and 11 collision domains

16 broadcast domains and 11 collision domains

54. What is a function of the distribution layer?

fault isolation
network access to the user
high-speed backbone connectivity
interconnection of large-scale networks in wiring closets*
55. Which switching method drops frames that fail the FCS check?
borderless switching
cut-through switching
ingress port buffering
store-and-forward switching*