number_mod_module U5smg_encoder_module U6smg_scan_module U7

row_scan_module U1column_scan_module U2
AD
smg_check U4
ad_tlc549 U3ADTI
**adRAMRAMip
*/
module experiment_ram(
clk,
rst,
//enable_ad,
ad_data,
row_scan_sig,
column_scan_sig,
ad_cs,
ad_clk
);

input clk;
input rst;

//input enable_ad;
input ad_data;

output [7:0] row_scan_sig;

output [2:0] column_scan_sig;
output ad_cs;
output ad_clk;

wire [7:0] smg_display_data;

ad_tlc549 U3
(
.clk(clk),
.rst(rst),
//.enable_ad(enable_ad),
.ad_data(ad_data),
.ad_cs(ad_cs),

.ad_clk(ad_clk),
.digit_data(smg_display_data)
);
/**/
/*
//smg_check
wire [7:0] smg_display_data;
smg_check U4
(
.clk(clk),
.rst(rst),
.smg_display_data(smg_display_data)
);
*/
wire [3:0] hundred_data;
wire [3:0] ten_data;
wire [3:0] one_data;
number_mod_module U5
(
.clk(clk),
.rst(rst),
.number_data(smg_display_data),
.hundred_data(hundred_data),
.ten_data(ten_data),
.one_data(one_data)
);

wire [7:0] hundred_smg_data;

wire [7:0] ten_smg_data;
wire [7:0] one_smg_data;
smg_encoder_module U6
(
.clk(clk),
.rst(rst),
.hundred_data(hundred_data),
.ten_data(ten_data),
.one_data(one_data),
.hundred_smg_data(hundred_smg_data),
.ten_smg_data(ten_smg_data),
.one_smg_data(one_smg_data)
);

smg_scan_module U7
(

.clk(clk),
.rst(rst),
.hundred_smg_data(hundred_smg_data),
.ten_smg_data(ten_smg_data),//8'b1100_0000
.one_smg_data(one_smg_data),//8'b1100_0000
.row_scan_sig(row_scan_sig),
.column_scan_sig(column_scan_sig)
);
endmodule
/*
***The maximum I/O CLOCK input frequency of the TLC548 is 2.048 MHz,
and the I/O CLOCK input frequency of theTLC549 is specified up to 1.1 MHz.
***the TLC548 and TLC549 provide an on-chip system clock that operates typically at 4 MHz
and requires no external components.
***Conversion Time...17 s Max
***NOTES: A. The conversion cycle, which requires 36 internal system clock periods (17 s
maximum),
is initiated with the eighth I/O clock pulse trailing edge after CS goes low for the
channel whose address exists in memory at the time.
B. The most significant bit (A7) is automatically placed on the DATA OUT bus after CS is
brought low. The remaining seven bits (A6A0) are clocked out on the first seven I/O
clock falling edges. B7B0 follows in the same manner.
**40 000 conversions per second for the TLC549
*/
module ad_tlc549(
clk,
rst,
//enable_ad,
ad_data,
ad_cs,
ad_clk,
digit_data
);

input clk;
input rst;
//input enable_ad;
input ad_data;

output ad_cs;
output ad_clk;
output [7:0]digit_data;

//2^(11)=2048
reg [10:0] clk_cnt;
always @ (posedge clk or negedge rst)
begin
if(!rst)
begin
clk_cnt<=11'd0;
end
else if(clk_cnt>=11'd1320)
begin
clk_cnt<=11'b0;
end
else
begin
clk_cnt<=clk_cnt+1'b1;
end
end

/*
50MHZ->0.02us
cs_high_data_exchange
17us->850clk
4000025us, 25us
cs_low_data_read
1.4us+81MHZ->1.4us+8us=9.4us ->70+400=470clk
total clk pulse=1320
*/
wire cs_high_data_exchange;
wire cs_low_data_read;
reg rcs;
assign cs_high_data_exchange=(clk_cnt>=11'd0) &&(clk_cnt<11'd850);
assign cs_low_data_read =(clk_cnt>=11'd850)&&(clk_cnt<11'd1320);
assign cs_low_data_read1 =(clk_cnt>=11'd920)&&(clk_cnt<11'd1320);
always @ (posedge clk or negedge rst)
begin
if(!rst)
begin
rcs<=1'b1;
end

else
begin
if(cs_high_data_exchange)
rcs<=1'b1;
else
rcs<=1'b0;
end
end
assign ad_cs=rcs;

//2^6=64
//50MHz501MHz
reg [5:0] div_cnt;
reg rad_clk;
reg [3:0] count_read_data_pulse;
always @ (posedge clk or negedge rst)
begin
if(!rst)
begin
div_cnt<=6'd0;
rad_clk<=1'b0;
count_read_data_pulse<=4'd0;
end
else if((cs_low_data_read1 )&&(count_read_data_pulse<8))
begin
div_cnt<=div_cnt+1'b1;
if(div_cnt<25)
begin
rad_clk<=1'b1;
end
else if(div_cnt>=49)
begin
count_read_data_pulse<=count_read_data_pulse+1'b1;
div_cnt<=6'd0;
end
else
rad_clk<=1'b0;
end
else if(!cs_low_data_read1)
begin
rad_clk<=1'b0;
count_read_data_pulse<=4'd0;
end
else
rad_clk<=1'b0;

end
assign ad_clk=rad_clk;

reg [7:0] rad_data;

always @ (posedge clk or negedge rst)
begin
if(!rst)
begin
rad_data<=8'd0;
end
else
begin
case (clk_cnt)
11'd920 :rad_data[7] <= ad_data;
11'd970 :rad_data[6] <= ad_data;
11'd1020:rad_data[5] <= ad_data;
11'd1070:rad_data[4] <= ad_data;
11'd1120:rad_data[3] <= ad_data;
11'd1170:rad_data[2] <= ad_data;
11'd1220:rad_data[1] <= ad_data;
11'd1270:rad_data[0] <= ad_data;
default:;

endcase
end
end
assign digit_data=rad_data;

endmodule

module smg_check(
clk,
rst,
smg_display_data
);
input clk;
input rst;
output [7:0] smg_display_data;
//50MHz500000001s100000000.2s
//parameter TIMES=26'd50000000;

parameter TIMES=24'd10000000;

reg [25:0] clk_cnt;

always @ (posedge clk or negedge rst)
begin
if(!rst)
clk_cnt<=26'd0;
else if(clk_cnt>TIMES)
clk_cnt<=26'd0;
else
clk_cnt<=clk_cnt+1'b1;
end

reg [7:0] rsmg_display_data;

always @ (posedge clk or negedge rst)
begin
if(!rst)
rsmg_display_data<=8'd0;
else if(rsmg_display_data>8'd255)
rsmg_display_data<=8'd0;
else if(clk_cnt==TIMES)
rsmg_display_data<=rsmg_display_data+1'b1;
end

assign smg_display_data=rsmg_display_data;

endmodule

module number_mod_module(
clk,
rst,
number_data,
hundred_data,
ten_data,
one_data
);
input clk;
input rst;
input [7:0] number_data;
output [3:0] hundred_data;
output [3:0] ten_data;

output [3:0] one_data;

reg [31:0] rhundred_data;

reg [31:0] rten_data;
reg [31:0] rone_data;
always @ (posedge clk or negedge rst)
begin
if(!rst)
begin
rhundred_data<=32'd0;
rten_data<=32'd0;
rone_data<=32'd0;
end
else
begin
rhundred_data<=number_data/100;
rten_data<=number_data%100/10;
rone_data<=number_data%10;
end
end

assign hundred_data=rhundred_data[3:0];
assign ten_data=rten_data[3:0];
assign one_data=rone_data[3:0];

endmodule

module smg_encoder_module(
clk,
rst,
hundred_data,
ten_data,
one_data,
hundred_smg_data,
ten_smg_data,
one_smg_data
);
input clk;
input rst;
input [3:0] hundred_data;
input [3:0] ten_data;
input [3:0] one_data;

output [7:0] hundred_smg_data;

output [7:0] ten_smg_data;
output [7:0] one_smg_data;

parameter _0 = 8'b1100_0000, _1 = 8'b1111_1001, _2 = 8'b1010_0100,

_3 = 8'b1011_0000, _4 = 8'b1001_1001, _5 = 8'b1001_0010,
_6 = 8'b1000_0010, _7 = 8'b1111_1000, _8 = 8'b1000_0000,
_9 = 8'b1001_0000;

reg [7:0] rhundred_smg_data;

always @ (posedge clk or negedge rst)
begin
if(!rst)
rhundred_smg_data<=8'b1111_1111;
else
case(hundred_data)
4'd0:rhundred_smg_data<=_0;
4'd1:rhundred_smg_data<=_1;
4'd2:rhundred_smg_data<=_2;
4'd3:rhundred_smg_data<=_3;
4'd4:rhundred_smg_data<=_4;
4'd5:rhundred_smg_data<=_5;
4'd6:rhundred_smg_data<=_6;
4'd7:rhundred_smg_data<=_7;
4'd8:rhundred_smg_data<=_8;
4'd9:rhundred_smg_data<=_9;
endcase
end
reg [7:0] rten_smg_data;
always @ (posedge clk or negedge rst)
begin
if(!rst)
rten_smg_data<=8'b1111_1111;
else
case(ten_data)
4'd0:rten_smg_data<=_0;
4'd1:rten_smg_data<=_1;
4'd2:rten_smg_data<=_2;
4'd3:rten_smg_data<=_3;
4'd4:rten_smg_data<=_4;
4'd5:rten_smg_data<=_5;
4'd6:rten_smg_data<=_6;
4'd7:rten_smg_data<=_7;

4'd8:rten_smg_data<=_8;
4'd9:rten_smg_data<=_9;
endcase
end
reg [7:0] rone_smg_data;
always @ (posedge clk or negedge rst)
begin
if(!rst)
rone_smg_data<=8'b1111_1111;
else
begin
case(one_data)
4'd0:rone_smg_data<=_0;
4'd1:rone_smg_data<=_1;
4'd2:rone_smg_data<=_2;
4'd3:rone_smg_data<=_3;
4'd4:rone_smg_data<=_4;
4'd5:rone_smg_data<=_5;
4'd6:rone_smg_data<=_6;
4'd7:rone_smg_data<=_7;
4'd8:rone_smg_data<=_8;
4'd9:rone_smg_data<=_9;
endcase
end
end
assign hundred_smg_data=rhundred_smg_data;
assign ten_smg_data=rten_smg_data;
assign one_smg_data=rone_smg_data;

endmodule

module smg_scan_module(
clk,
rst,
hundred_smg_data,
ten_smg_data,
one_smg_data,
row_scan_sig,
column_scan_sig
);
input clk;
input rst;

input [7:0] hundred_smg_data;

input [7:0] ten_smg_data;
input [7:0] one_smg_data;
output [7:0] row_scan_sig; // --
output [2:0] column_scan_sig; // --

row_scan_module U1
(
.clk(clk),
.rst(rst),
.hundred_smg_data(hundred_smg_data),
.ten_smg_data(ten_smg_data),
.one_smg_data(one_smg_data),
.row_scan_sig(row_scan_sig)
);

column_scan_module U2
(
.clk(clk),
.rst(rst),
.column_scan_sig(column_scan_sig)
);

endmodule

module row_scan_module(
clk,
rst,
hundred_smg_data,
ten_smg_data,
one_smg_data,
row_scan_sig
);
input clk;
input rst;
input [7:0] hundred_smg_data;
input [7:0] ten_smg_data;
input [7:0] one_smg_data;
output [7:0] row_scan_sig;

parameter TIMES=18'd199_999;

reg [17:0] count;

always @ (posedge clk or negedge rst)
begin
if(!rst)
count<=18'd0;
else if(count==TIMES)
count<=18'd0;
else
count<=count+1'b1;
end
reg [1:0] t;
always @ (posedge clk or negedge rst)
begin
if(!rst)
t<=2'd0;
else if(t==2'd3)
t<=2'd0;
else if(count==TIMES)
t<=t+1'b1;
end

reg [7:0] rdata;

always @ (posedge clk or negedge rst)
begin
if(!rst)
rdata<=8'd0;
else if(count==TIMES)
begin
case(t)
2'd0:rdata<=hundred_smg_data;
2'd1:rdata<=ten_smg_data;
2'd2:rdata<=one_smg_data;
default:;
endcase
end
end
assign row_scan_sig=rdata;

endmodule

module column_scan_module(
clk,
rst,
column_scan_sig
);
input clk;
input rst;
output [2:0] column_scan_sig;

parameter TIMES=18'd199_999;

reg [17:0] count;

always @ (posedge clk or negedge rst)

begin
if(!rst)
count<=18'd0;
else if(count==TIMES)
count<=18'd0;
else
count<=count+1'b1;
end

reg [1:0] t;
always @ (posedge clk or negedge rst)
begin
if(!rst)
t<=2'd0;
else if(t==2'd3)
t<=2'd0;
else if(count==TIMES)
t<=t+1'b1;
end
reg [2:0] rcolumn_scan_sig;
always @ (posedge clk or negedge rst)
begin
if(!rst)
begin
rcolumn_scan_sig<=2'b10;

end
else if(count==TIMES)
begin
case(t)
2'd0:rcolumn_scan_sig<=3'b011;
2'd1:rcolumn_scan_sig<=3'b101;
2'd2:rcolumn_scan_sig<=3'b110;
default:;
endcase
end
end
assign column_scan_sig=rcolumn_scan_sig;

endmodule