GE

Digital Energy

D20 Control
Output Module
Overview
The D20 Control module is composed of two detachable modules, WESTERM D20 K and WESDAC D20 K.
The top module, WESDAC D20 K, processes the data acquired and communicates this to the main D20
processor, see Figure 2.
The bottom module, WESTERM D20 K, is composed of terminal blocks where field wirings are terminated.
The WESTERM D20 K termination board handles all connections to and from the WESDAC D20 K module.
These connections are:
The D.20 network ports
The 9600 baud RS232 maintenance port
The WESDAC D20 K module address
The relay outputs

Efficient, Cost Effective

I/O Solutions
The I/O modularity allows for efficient
distributed I/O installations - minimizing wiring
and enclosure requirements; this eliminates
panel and reduces cost
The active/passive design of the WESDAC/
WESTERM I/O modules allows users to
quickly test, commission, and troubleshoot
via hot swappable WESDAC modules,
without disturbing wiring connections ;
this significantly speeds up and simplifies
maintenance activities

External DC supply for control output voltage

The D20K is a 32-point control output interface module. The 32 output drivers can be arranged in several
hardware/software configurations, depending on the system requirements. The D20K ensures secure
operation of the control output interface. All control actions requested by the D20 main processor are
initiated, timed, reset and validated by the D20K.
The D20K also provides a Local/Remote switch and control output fusing. The Local/Remote switch
is a manually operated switch used to disable D20K relay coil power during maintenance. An off-line
indication is passed to the D20 main processor, which is available as a pseudo status to the host.
Two DB 9 connectors are provided to allow daisy chaining of the D.20 Link. This link provides the
communication channel over which the main D20 CPU processor can communicate with the WESDAC
D20 K. Power for the WESDAC D20 K is also provided over the same cable assembly. A single DB 9
connector is provided for the WESMAINT D20 maintenance port via a VT100 terminal emulator.
The address jumper block for the WESDAC D20 K is located on the WESTERM D20 K. The address on the
jumper block corresponds to the modules address on the D.20 link.
Only passive components are mounted on the WESTERM D20 K leaving all the active components on
the WESDAC D20 K.
This WESTERM and WESDAC arrangement simplifies field repair and maintenance setup since the
WESDAC D20 K can be replaced without disturbing any of the field wiring.

imagination at work

Ease of Use
To first time users, both the software
configuration setup and hardware
installations are trivial; this makes it simple to
install and maintain the control module

Flexible and Reliable

Operations
The digital output module can be easily
configured to support trip-close, raise-lower,
and form C types of configurations
D20K supports up to 32 digital outputs that
are isolated. It ensures the secure operation of
the control output interface by validating the
initiated and timed control request from the
D20/D200 Substation controller
I/O modules are available to be ordered with
either a DNP3 communication protocol option
or a Standard/ Redundant D.20 link option
the D.20 link is a GE proprietary protocol

Distributed I/O Architecture

SCADA Masters

The D20 Remote Terminal Unit (RTU) design is based on a distributedprocessing architecture including the real-time data acquisition and control
software. These I/O modules can be located close to the primary equipment
being monitored and controlled as they receive and send data back to the
master D20 main processor.
The I/O modules are intelligent modules that contain on-board
microprocessors and are configured as slave devices to the D20 main
processor. In the figure 1 pictorial setup, specific I/O processing is distributed
throughout the D20 RTU to the appropriate I/O modules.
The I/O modules support two communication protocols: (1) DNP 3 protocol,
and (2) high speed, high-level data link controller (D.20 Link) in the form of
poll and response messages protocol. The peripheral modules have serial
communication ports and various types of field connections.
The hardware construction of each remote I/O module type is similar (see
Figure 2.)

Figure 1: Simple architecture of I/O modules communicating to the D20 RTU

Figure 2: Architecture of I/O logic and termination panels

Acrylic Display
Cover

WESDAC
Logic Panel

WESTERM
Terminal Panel

Terminal Blocks

GEDigitalEnergy.com

Metal Mounting Plate

Control Output
Configurations/Applications

D20KI Interposing Relay Panel

The D20K can have one of the following control output configurations:
32 Trip/Close pairs
24 Trip/Close and 4 Raise/Lower pairs

For applications requiring heavy-duty control ratings, the D20K can be

connected to field equipment through interposing relays. The standard
D20KI interposing relay panel is equipped with P&B KUEP and KUP
interposing relays (10 A at 150 VDC and 10 A at 240 VAC respectively). It is
used in conjunction with a D20KR termination panel, as shown in figure 3.

16 Trip/Close and 8 Raise/Lower pairs

D20K I/O Peripheral

8 Trip/Close and 12 Raise/Lower pairs

16 Raise/Lower pairs
32 Isolated Form-C contact control outputs
32 Isolated open-drain outputs.

Interposing Relays

The hardware and software can also be configured to provide a wide range
of control output schemes, including parallel, pulse duration, pulse trains
and latched-output applications.
The control output duration is software-adjustable from 1 to 215 ms in onemillisecond increments, and on a per-point basis (protocol dependent). The
D20K software also supports discrete timed/latch relay functionality.

Termination Panel

Termination Types
D20 Control output module can be ordered with the following field
termination options:
Compression
Field wiring is terminated directly onto board-mounted screw terminal
compression blocks (#12 AWG [2.05mm] max, blade screwdriver - 0.6 x
3.5 x 100 mm) on the D20 I/O Peripheral
DB25
Field wiring is terminated onto the D20 I/O peripheral through DB25
connectors

To Field Equipment
Figure 3: Interposing Relays

D20KI Termination Board Options

The following D20KI termination board options are currently available online:
http://store.gedigitalenergy.com/ViewProd.asp?Model=D20+KI

Compression Disconnect
Field wiring is terminated onto plug-on terminator blocks (#12 AWG
[2.05mm] max, blade screwdriver - 0.6 x 3.5 x 100 mm), which then mate
with board-mounted headers on the D20 I/O Peripheral.

GEDigitalEnergy.com

Technical Specifications
Table 1: D20K Specifications
ITEM

DESCRIPTION

ITEM

DESCRIPTION

Processor

8 bit Freescale 68HC11 MPU

Coil Status Check

Every 500 s

Clock

2 MHz MPU clock

Contact Duration

Memory

32 KB EPROM
24 KB static RAM
512 bytes EEPROM

Programmable 1 to 215 ms in 1 ms
intervals (protocol dependent)

Switches

Local Enable/Disable Switch

Component Isolation Rating

1500 Vrms

Control Outputs

32 open collector drivers for relays

Four additional open collector drivers
for dedicated Master Trip/Close and
Test Breaker relays

Dielectric Rating

1000 VDC

D.20 Link Ports

Maintenance Port

9600 baud, RS-232

Power Requirements

2060 VDC, 4 W typical at 24 V, 11 W max.

at 24 V with all relays energized

Size

D20K logic board and D20K relay

termination board assembly: 19 x
5.25 x 2.5

Output Types

Momentary (fixed)
Latching
Trip/Close (T/C)
Raise/Lower (R/L)

D20KI1 interposing relay board

(compression terminals): 19 x 5.25

Pulse duration
Pulse train

Non matrixed output

configurations

D20KI2 interposing relay board (barrier

terminals): 19 x 7

32 T/C pairs
24 T/C + 4 R/L pairs

D20KR termination board for D20KI1/

D20KI2: 19 x 5.25

16 T/C + 8 R/L pairs

8 T/C + 12 R/L pairs

D20KI-OPC (517-0215): Interposing

relay panel for D20SD and D20CD,
equipped with sliding link terminal
blocks.

16 R/L pairs
32 isolated Form-C contact outputs
Optional 32 isolated open-drain
outputs, rated 150 mA @ 60VDC

LED Indicators

D20KI Contact ratings &

types (typical)

Momentary relays: 60 W max, 3 A max,

220 VDC max. (1 Form C or A)

D20K Contact ratings &

types (typical)

Interposing relays: 10 A @ 150 VDC (1

Form X), 5 A @ 150 VDC (2 Form A), 3 A
@ 150 VDC (2 Form C)
Interposing relays: 10 A @ 28 VDC (2
Form C or A)
PRD Series Relays:
PRD3, 20 A @ 125VDC, 1 Form X
PRD11, 20 A @ 125VDC, 2 Form C,
24VDC coil
PRD11, 20 A @ 125VDC, 2 Form C,
48VDC coil
Latching interposing relays:
10 A @ 28 VDC or 240 VAC (2 Form C)
Interposing relays (heavy duty):
20 A @ 125 VDC, 30 A @ 240 VAC
(1 Form A)

GEDigitalEnergy.com

Common LEDs
Local (GREEN) LED, which turns on
when the I/O module is set to Local
module using the Local/Remote switch,
or if the modules control software has
been disabled.
Remote (RED), which turns on when the
module is in Remote mode.
Control points (RED), which turn on
when the particular control point is
enabled.

Ordering
D20K System Components
Please note
1. For the rules regarding the combination of various options to build an
order code, visit the online web:
http://store.gedigitalenergy.com/ViewProd.asp?Model=D20K

3. The order defined in the ordering guide may not be final and can only be
accepted once GE has reviewed and accepted the order. This document is
only meant as a guide and by no means will portray the final order.

2. This ordering guide should ONLY be used with reference to the product
documentation and it is assumed the user has read those documents.
The ordering guide is for the use of experienced users who have extensive
knowledge in the area and the products.

4. GE reserves the rights to change or modify the document without notice.

The user is responsible to contact GE before placing an order to ensure
the accuracy of the order code built.

D20K -

D20K Termination

1
F
2
3
G
5
K
H
J

D20 PCommon

D.20 Cable

D.20 Terminator
D.20 Duct Panel

Second D.20 LAN

Description

Equivalent Legacy #
517-0164
517-0164-CC
517-0143
517-0218
517-0218-CC
517-0242
517-0242-CC
517-0220
517-0235

U
A

D20K, 32 Channel LV (20-60 VDC or D.20 Power) Compression Termination

D20K, 32 Channel LV (20-60 VDC or D.20 Power) Compression Termination (Conformal Coated)
D20KR, 32 Channel LV (20-60 VDC or D.20 Power) DB25 Termination
D20KX, 32 Channel LV (20-60 VDC or D.20 Power) Compression Disconnect Termination
D20KX, 32 Channel LV (20-60 VDC or D.20 Power) Compression Disconnect Termination (Conformal Coated)
D20K4Z, 32 Channel HV (40-150 VDC) Compression Termination
D20K4Z, 32 Channel HV (40-150 VDC) Compression Termination (Conformal Coated)
D20KR, 32 Channel LV (20-60 VDC or D.20 Power) DB25 Termination with Type 2 wire-wrap adapter
D20KR, 32 Channel LV (20-60 VDC or D.20 Power) DB25 Termination with SOLID STATE RELAYS
PCommon Chip Not Required
PCommon 212
PCommon 213
PCommon 220
PCommon 221
PCommon 300
PCommon 301
PCommon 305
PCOMMON 306 (D20A, D20S and D20K)
Cable Not Required
D.20 Cable 12 Inches Long
D.20 Cable 18 Inches Long
D.20 Cable 24 Inches Long
D.20 Cable 36 Inches Long
D.20 Cable 48 Inches Long
D.20 Cable 72 Inches Long
D.20 Cable 96 Inches Long
D.20 Cable 120 Inches Long
D.20 Terminator Not Required
D.20 Terminator (One Required per D.20 Link)
Duct Panel Not Required
Cable Duct Panel, Tie Wrap Connections
Two Cable Duct Panels, Tie Wrap Connections
Cable Duct Panel, No Through Holes
Two Cable Duct Panels, No Through Holes
Cable Duct Panel, Through Holes at Each End
Two Cable Duct Panels, Through Holes at Each End
Second D.20 LAN Port Not Required
WESDAC D20 ASK D.20 I/F

U
1
2
3
4
5
6
7
8
U
1
2
3
4
5
6
7
8
U
1
U
1
2
3
4
5
6

GEDigitalEnergy.com

D20K Spare Components

Please note
1. For the rules regarding the combination of various options to build an
order code, visit the online web:
http://store.gedigitalenergy.com/ViewProd.asp?Model=D20K+Spare+Parts+

3. The order defined in the ordering guide may not be final and can only be
accepted once GE has reviewed and accepted the order. This document is
only meant as a guide and by no means will portray the final order.

2. This ordering guide should ONLY be used with reference to the product
documentation and it is assumed the user has read those documents.
The ordering guide is for the use of experienced users who have extensive
knowledge in the area and the products

4. GE reserves the rights to change or modify the document without notice.

The user is responsible to contact GE before placing an order to ensure
the accuracy of the order code built.

D20K -

Module Type

T
D
3

Input Voltage to Module

Termination Type

Environmental Protection

D20K Special Options

D.20 Link

PCOMMON

DNP3 Digital Output

Points Configuration
Wire Wrap Adapter

Description

U
A

WESTERM Module
WESDAC Module
DNP 3 I/O Module
None (Need ONLY RNET Voltage Adapter Packs)
High Voltage (40-150VDC)
Low Voltage (20-60 VDC or D.20 Link Power)
None
DB25 Termination Type
Compression Termination Type
Compression/Disconnect Terminatiion Type
None
Conformal Coat
Epoxy-Conformal Coat
None
WESTERM allows for D.20 Link and Dual PS Input
WESTERM allows for Wire Wrap Adaptor Connection
None
WESTERM Redundant D.20 Link & Dual Power Supply Option (540-0313)
WESDAC Redundant D.20 Link & Dual Power Supply Option (540-0207)
Standard D.20 Link [ For Module type T, or D] (540-0162)
None
PCommon 212 (SBA0001/00)
PCommon 213 (SBA0003/00)
PCommon 220 (SBA0004/00)
PCommon 221 (SBA0007/00)
PCommon 300 (SBA0005/00)
PCommon 301 (SBA0006/00)
PCommon 305 (SBA0009/00)
PCOMMON 306 (P010-0 VER.306)
None
Trip/Close Configuration
Raise/Lower Configuration
None
WESTERM D20K Wire Wrap Adapter [517-0228]

U
H
L
U
D
P
X
U
C
E
U
R
W
U
R
L
S
U
1
2
3
4
5
6
7
8
U
A
B

GEDigitalEnergy.com

D20K Spare Cross-Reference

LEGACY PART NUMBER AND DESCRIPTION

SMART CATALOG NUMBER PREFIX AND DESCRIPTION

WESTERM MODULES - LEGACY PART NUMBER

WESTERM MODULES - NEW PART NUMBER PREFIX

(517-0164) - WESTERM D20K TYPE 1 VERSION 1

(D20K-TL-P-UU) - D20K LV (20-60VDC or D.20 Power), Compression Termination

(517-0164-CC ) - WESTERM D20K TYPE 1 VERSION 1 (CONFORMAL COATED)

(D20K-TL-P-CU) - D20K LV (20-60VDC or D.20 Power), Compression Termination, Conformal Coated

(517-0143) - WESTERM D20 KR

(D20K-TL-D-UU) - D20KR LV (20-60VDC or D.20 Power), DB25 Termination

(517-0143-CC) - WESTERM D20 KR (CONFORMAL COATED)

(D20K-TL-D-CU) - D20KR LV (20-60VDC or D.20 Power), DB25 Termination, Conformal Coated

(517-0218) - WESTERM D20KX W/TB PLUGS

(D20K-TL-X-UU) - D20KX LV (20-60VDC or D.20 Power), Compression Disconnect Termination

(517-0218-CC) - WESTERM D20KX W/TB PLUGS (CONFORMAL COATED)

(D20K-TL-X-CU) - D20KX LV (20-60VDC or D.20 Power), Compression Disconnect Termination, Conformal Coated

(517-0242) - WESTERM D20 K4Z

(D20K-TH-P-UU) - D20K4Z HV (40-150VDC or D.20 Power), Compression Termination

(517-0242-CC) - WESTERM D20 K4Z (CONFORMAL COATED)

(D20K-TH-P-CU) - D20K4Z HV (40-150VDC or D.20 Power), Compression termination, Conformal Coated

(517-0242 - ECC) - WESTERM D20 K4Z - Epoxy Conformal Coat

(D20K-TH-P-EU) - D20K4Z HV (40-150VDC or D.20 Power), Compression Termination, Epoxy Conformal Coated

(517-0220) - WESTERM D20KR TYPE 2

(D20K-TL-D-UW) - D20KR TYPE 2 LV (20-60VDC or D.20 Power), DB25 Termination with Wire-Wrap adapter option

(517-0250) - WESTERM D20 OKR

(D20K-TL-D-UR) - D20 OKR LV (20-60VDC or D.20 input), Compression Termination, redundant D.20 and PS Input

WESDAC MODULES - LEGACY PART NUMBER

WESDAC MODULES - NEW PART NUMBER PREFIX

(508-0101) - WESDAC D20K TYPE 1 VERSION 1

(D20K-DL-U-UU) - WESDAC D20K LV

(508-0101-CC) - WESDAC D20K TYPE 1 VERSION 1 (CONFORMAL COATED)

(D20K-DL-U-CU) - WESDAC D20K LV, Conformal Coated

(508-0102) - WESDAC D20K HV

(D20K-DH-U-UU) - WESDAC D20K HV

(508-0102-CC) - WESDAC D20K HV (CONFORMAL COATED)

(D20K-DH-U-CU) - WESDAC D20K HV, Conformal Coated

(508-0102-ECC) - WESDAC D20 KHV - Epoxy Conformal Coat

(D20K-DH-U-EU) - WESDAC D20K HV, Epoxy Conformal Coated

DNP 3 CONTROL MODULES - LEGACY PART NUMBER

DNP 3 CONTROL MODULES - NEW PART NUMBER PREFIX

(508-0301) - DNP I/O MODULE - CONTROL

(D20K-3L-U-UU)- WESDAC D20K LV, DNP3 Communications

(508-0301-CC) - DNP I/O MODULE - CONTROL (CONFORMAL COATED)

(D20K-3L-U-CU)- WESDAC D20K LV, DNP3 Communications, Conformal Coated

(508-0302) - DNP I/O MODULE - CONTROL HV

(D20K-3H-U-UU)- WESDAC D20K HV, DNP3 Communications

(508-0302-CC) - DNP I/O MODULE - CONTROL HV (CONFORMAL COATED)

(D20K-3H-U-CU)- WESDAC D20K HV, DNP3 Communications, Conformal Coated

Note: The cross reference tab attempts to compare the old part numbers to the new smart catalogue numbers. The new smart catalogue numbers represented
are the prefix or base line for the complete catalogue number. For the complete catalogue number, and to determine the selections for the various sub
components, visit: http://store.gedigitalenergy.com/ViewProd.asp?Model=D20K+Spare+Parts+
See figure 9 for examples of sub components specific to a user: D20K Special options, D.20 Link options, D20 PCOMMON options, DNP3 control output
configuration, D20K Wire Wrap Adapter.

GEDigitalEnergy.com

GE Digital Energy
650 Markland St.
Markham, ON
Canada L6C 0M1
+1 877-605-6777 (toll free in North America)
+1 678-844-6777 (direct number)
[email protected]

GEDigitalEnergy.com

Copyright 2014, General Electric Company.

GE and the GE monogram are trademarks of the General Electric Company.

imagination at work

GE Digital Energy reserves the right to make changes to specifications of products described at any
time without notice and without obligation to notify any person of such changes.
GEA-12711A(E)
English
140627