Ingenico Ict220 Users Manual 120304

Terminal User Guide
iCT220 & ML30
Contents
Section Title Page
1.
Introduction 2
2.
Important Safety Instructions 2
3.
Declaration of Conformity 5
4.
Installing the Terminal 6
5.
Using the Terminal 9
6.
Starting a Transaction 13
7.
Sale Transactions 13
8.
Setting the Referral Password 18
9.
Refunds 19
10.
Purchase with Cashback 20
11.
Cash Advance 21
12.
Purchase with Gratuity (Restaurants)
21
Refund with Gratuity 23
13.
14.
Pre-Authorisation 24
15.
Completion 25
16.
Key Entering Card Details and Mail Order Transactions
25
17.
Reversal 28
18.
Verify Account 28
19.
PIN Entry Failure 29
20.
Cancelling Transactions 29
21.
Clearing Mistakes 30
22.
Printing Duplicate Receipts 30
23.
X and Z Totals 30
24.
Waiter Totals 31
25.
End-of-Day Banking 31
26.
Entering Function Codes 32
27.
Waiter IDs (Restaurants) 33
28.
How to Change the Date and Time
34
29.
How to Print a Transaction Log
35
30.
How to Change a Paper Roll
36
31.
Insuring the Terminal 36
Security Warning Notice 36
32.
33.
Helpful Hints 37
34.
Miscellaneous Prompts 38
1.
Introduction
This guide will detail how you install and use your ICT220 terminal with ML30 PINpad, including safety
information and instructions on transaction processing, printing reports and general maintenance of the
terminal.
2.
Important Safety Instructions
Take care when unpacking, and inspect the product for any obvious external, or suspected internal
damage. When in doubt, do not proceed to install or operate equipment. Contact your supplier.
General Safety Information

This equipment has been designed and manufactured to meet international safety standards but, like
any electrical apparatus, due care must still be taken.

Do read and understand the instructions before using the equipment.

Do Not expose this apparatus to rain or moisture. For indoor use only.
Do Not remove any screws or non-operator accessible covers.
Do Not insert any metallic objects.
Do Not stack telephone splitters.
Do Not allow liquid to spill into cabinet openings.
Do Not allow anything to rest on the power or telecom cords and ensure all cables are routed to
prevent damage or accidental contact.
Do Not continue to operate the equipment if you are in any doubt about it working normally, or
if it is damaged in any way. Switch off then withdraw the mains plug and consult your service
agent.
Service Requirements
Operator Access (ESD Precaution)
This is an Electrostatic (ESD) sensitive area. As a minimum, the operator should be Electrostatically
Discharged via his/her hand to a suitable metallic earthing point prior to opening this area.
There are no other user serviceable parts inside. In the event of equipment malfunction, unplug the
power supply. It is the responsibility of users requiring service to report the need for service to the
authorised Service Agent.
Maintenance
Cleaning the Casing

DO NOT allow any water to enter inside the casing. Remove any dust from the casing using a
damp cloth. To clean off accumulated dirt and grime, use a damp cloth that has previously been
dipped in mild soap and water. Wring out thoroughly to remove excess water before use.
DO NOT use solvents, cleaning fluids or abrasives. These materials could damage the plastic
housing and any exposed contacts.
Page 2
External Power Supply

This apparatus is intended for use when supplied with power from a low voltage external power
supply.
Only an Ingenico approved power supply (CE Marked) specified for use with this Terminal may be
used.
Since this product does not have a disconnect device (ON/OFF switch), the Terminal and Power
Supply must be installed near a suitable power socket which is easily accessible.
In the event of a hazard or malfunction, the Power Supply Unit should be switched off at the
socket before being unplugged from the mains.
The power supply output lead should only be plugged into the product power input socket.
The power supply will provide adequate power for the Terminal. The user should ensure that all
other auxiliary apparatus, drawing power from the host, does not overload the power supply.
Operate only from a power source as specified on the Power Supply Unit.
A damaged mains cord (if not a replaceable type) or low voltage secondary input lead cannot
be replaced by the user, the unit must be returned to the authorised service agent for essential
repairs and/or replacement.
Connections
Interconnection to other equipment via the externally accessible ports on the Terminal must only be
made as follows:
Power Supply Input: Operates at Safety Extra Low Voltage (SELV). Connect only to an Ingenico
approved Power Supply (CE Marked) specified for use with the Terminal.
Port(s), 6 way: The RS232 type port(s) operate at SELV and must only be connected to a module
of the same type ie. SELV.
Public Switched Telephone Network (PSTN) Line, 6 Way: MUST only be connected to a PSTN socket
e.g. Telephone wall socket, PABX etc.
Under no circumstances must the PSTN cable be inserted into the RS232 ports. Take due care when
attaching cables.
External Cables
DO NOT use any other external cables and/or cable lengths (must be less than 3 metres long) other
than those specified and/or supplied by the manufacturer. Ensure all cables are routed to prevent
damage or accidental contact.
Page 3
MODEM
General Description
The Terminal has an integral modem that allows the Terminal to transfer transaction data to card
companies host computer systems.
The internal modem supports: CCITT V22bis/V22/V21/V32, V32bis, V34 data transfer protocols.
It has an automatic dialling facility.
Disclaimer
This equipment has been designed for connection to the local Public Switched Telephone Network
(PSTN). The apparatus must not be subjected to any modification, in any material way, unless
authorised by Ingenico. Nor must it be used with:

Internal Modem Software that has not been formally accepted by the manufacturer.
External control Software or external control equipment which causes operation of the modem or
associated call set up equipment to contravene the requirements of the PSTN Network.
Systems to which the Modem may be connected

This Modem is only approved for connection to the following telecommunications systems:

The Public Switched Telephone Network (PSTN).

Any equivalent service run by any Licensed Telecommunications Network Operator.
Private Branch Exchange (PABX) extensions, being a Branch Telecommunications System operating
under a license.
The Modem is not suitable for shared service or 1+1 carrier systems nor as an extension to a
pay-phone.
Note: It cannot be guaranteed that the Modem will operate correctly under all possible conditions of
connection to PABXs. Any cases of difficulty should be referred in the first instance to Ingenico.
Connection
The modem is connected to the PSTN via a standard plug and flexible cord, which requires a suitable
compatible socket (and adaptor if required).
Terminals connected to phone lines where a broadband service is present must be connected through
an ADSL microfilter.
Dialling
This modem is suitable only for connection to direct exchange and/or PABX lines which provide Dual
Tone Multi Frequency (DTMF) dialling facilities.
Ringer Equivalence Number (REN)
To determine the total number of items of apparatus that should be connected simultaneously to an
exclusive PSTN line, the total REN values of each of the items of apparatus connected to the line should
not exceed the maximum REN value 4.0. This value includes any Network operator provided
instrument, each of which is assumed to have a REN value of 1.0 unless otherwise marked.
Page 4
3.
Declaration of Conformity
The CE marking indicates that the product supplied complies with the basic requirements of European
Directive 1999/5/CE known as the R&TTE Directive concerning RF equipment and telecommunications
terminals with respect to:

The protection of the health and safety of the user and any other person.
The protection requirements with respect to electromagnetic compatibility.
and complies with the following harmonised standards:

IEC/EN 60950 1
Issued
Dec 2001
Electrical safety of data processing

equipment
EN 55022
Issued
1998/A1-2000/A2-2003
Radio electric disturbance characteristics

limits and measurement methods
EN 55024
Issued
1998/A1-2000/A2-2003
Immunity characteristics limits and

measurement methods
And, for the whole range, complies with the European approval specification on connecting terminals
with DTMF dialling to the Public Switched Telephone Network (Council Decision 1998/482/EC, Council
Decision 1999/303/EC).
ETSI ES 203021
ETSI TR 103000
The product supplied is designed to interwork with the following European analogue Public Switched
Telephone Networks:
Austria, Belgium, Denmark, Finland, France , Germany, Greece, Iceland, Ireland, Italy, Liechtenstein,
The Netherlands, Norway, Portugal, Spain, Sweden, Switzerland, United Kingdom.
WEEE Directive
The product belongs to the family of electrical and electronic equipment. Therefore it is subjected to
the WEEE Directive which requires the collection and recycling at the end of the life of the product.
Ingenico products present the symbol for the marking of electrical and electronic equipment as
required by the WEEE Directive.
The crossed through wheeled bin printed on the product gives information about the
requirement not to dispose of WEEE as unsorted municipal waste and to collect such WEEE
separately.
To ensure that the product is collected and recycled with respect to the environment, you must contact
your supplier (contact the Ingenico local office or the commercial head office in charge of your country
on www.ingenico.com <<contact us>> page).The abandonment or uncontrolled disposal of waste can
harm the environment and human health.
So, by recycling your product in a responsible manner you contribute to the preservation of natural
resources and the protection of human health.
Batteries
If your product contains batteries they must be disposed of at the appropriate collection points.
Page 5
4.
Installing the Terminal
Installing the Terminal via PSTN

Before switching the power on at the mains socket, plug the pre-connected telephone cable into your
telephone wall socket.
Position the terminal in a clear area where the display can be read and the keypad and card swipe are
easily accessible. Position the PINpad where it will be easily accessible to the cardholder.
Ensure you have your Merchant ID to hand. This can be found on your Welcome Letter.
Now switch the power on at the mains supply and Installation will begin.
Dual Comms Mode

1.
You should use the

arrows to highlight the
required option and then press ENTER to select Telephone (PPP) for PSTN.
Connection Method
Telephone (PPP)
LOCAL NETWORK
Terminal Displays
2.
PINpad Displays
Terminal Installation
Plug in Phone Line
<Software Version>
<Serial Number>
and then press ENTER
Ready
Ensure the telephone line is connected to the telephone IN port on the terminals connector box
and to the wall socket and then press the GREEN button.
Dial Prefix Required ?
<Software Version>
<Serial Number>
Enter=YES Clear=NO
Ready
If your terminal it is connected to a Switchboard/PABX select YES by pressing the GREEN button. Key in
the number used to get an outside line (often 9)and then press the GREEN button.
Key in the Number used
to get an Outside Line
<Software Version>
<Serial Number>
Ready
If however your terminal is connected via a direct line and you selected NO by pressing the YELLOW
button.
Does the Tel. Line have
Call Waiting or 1571 ?
<Software Version>
<Serial Number>
Enter=YES
Ready
Clear=NO
If your telephone line has Call Waiting or 1571 press the GREEN button.
Page 6
PLEASE NOTE: If you have Call Waiting and select NO when prompted, the terminal will be unable to
dial for authorisation when a call message is waiting.
3.
Key in your Merchant Number and press the GREEN button.

Key in Merchant No.
<Software Version>
<Serial Number>

Ready
The terminal will start to dial Ingenico terminal configuration system (GEMS) and a number of
communication messages will be displayed.
Connecting to
<Acquirer Name>
Please Wait...
<Software Version>
<Serial Number>
Ready
Once the configuration call completes, the terminal will then contact each acquirer of the cards it is
configured to accept. Further communications messages will be displayed.
Hardware Serial
Validation
Required
Press ENTER
POWERING UP

Please Wait...
An installation report will then be printed displaying the card types that your terminal will accept.
NOTE: If the print out shows cards type not accepted please contact the Helpdesk.
The PINpad will now be installed; when you see the display below press the GREEN button.
The terminal will start to dial the GEMS to validate the PINpad serial number.
Once the call to GEMS has completed the installation of the PINpad is complete.
Installation of the terminal and the PINpad is now complete and the terminal will display the READY
prompt. The terminal and PINpad are now ready for use.
READY
Merchant Number
12345678
<IDLE DISPLAY>
Before you start using the terminal confirm that the date and time are correct. If this needs to be
amended refer to Section 28 of this guide for details.
Page 7
Installing the Terminal via Ethernet (IP)

Before switching the power on at the mains supply, ensure that the Ethernet cable is connected to the
ETH port on the terminals connector box, and to your router or network point.
Position the terminal in a clear area where the display can be read and the keypad and card swipe are
easily accessible. Position the PINpad where it will be easily accessible to the cardholder.
Ensure you have your Merchant ID to hand. This can be found on your Welcome Letter.
Now switch on the power at the mains supply and installation will begin.
Dual Comms Mode

1.
You should use the

keys to highlight the
required option and then press the GREEN button when
Local Network is selected.
Connection Method
Telephone (PPP)
LOCAL NETWORK
Terminal Displays
Plug in Network
Cable
PINpad Displays
<Software Version>
<Serial Number>
Ready
Ensure the Network Cable is connected and then press the GREEN button.
2.
Key in your Merchant Number and press the GREEN button.

Key In Merchant No.
<Software Version>
<Serial Number>
Ready
The terminal will connect to the Ingenicos terminal configuration system (GEMS) and a number of
communication messages will be displayed.
Once the configuration call completes, will then contact each acquirer of the cards it is configured
to accept. Further communications messages will be displayed.
Connecting to
<Acquirer Name>
Please Wait...
3.
<Software Version>
<Serial Number>
Ready
An installation report will then be printed displaying the card types that your terminal will accept.
The terminal will dial GEMS to validate the PINpad serial number.
Hardware Serial
Validation
Required
Press ENTER
POWERING UP
Please wait...
PLEASE NOTE: If the print out shows cards type not accepted please contact the Helpdesk.
Page 8
Once the call to GEMS has completed the installation of the PINpad is complete.
Installation of the terminal is now complete and the terminal will display the READY prompt.
When you see the display below press the GREEN button.
READY
Merchant Number
12345678
<IDLE DISPLAY>
Before you start using the terminal confirm that the date and time are correct. If this needs to be
amended refer to Section 28 of this guide for details.
5.
Using the Terminal
Inserting a Chip Card into the PINpad

The card should always be inserted into the PINpad with the
chip facing uppermost.
If the card is inserted the wrong way or there is a problem
with the chip, the terminal will prompt for the card to be
removed and re-inserted.
The PINpad will prompt you when the card is to be
removed.
Inserting a Chip Card into the Terminal

If the PINpad is inoperable for any reason and you have had your terminal re-configured to work in
standalone mode, the card should be inserted into the terminal with the chip facing uppermost.
The terminal can detect if a chip card has been swiped as a magnetic card. If the card has not been
inserted previously, it will prompt you to insert the card.
If the card is inserted the wrong way or there is a
problem with the chip, the terminal will prompt for
the card to be removed and re inserted.
The terminal will prompt you when the card
is to be removed.
Page 9
Swiping a Card
The card should be swiped through the PINpad with the black magnetic stripe facing the terminal and
running along the bottom of the card. You will be required to swipe the card if the chip cannot be read
or if the customer has a card with only the magnetic swipe.
Make sure that the bottom of the card runs firmly along the bottom of the card swipe and that the card
is swiped at an even speed.
The speed of the card swipe should not be too slow as this can sometimes cause problems when the
terminal is reading the card.
PLEASE NOTE: It is important to swipe cards correctly through the terminal so that they can be read by
the card reader.
Using a Card with the Contactless Reader

The Contactless Card Reader is located on the PINpad. If the terminal is allowed to process Contactless
transactions the cardholder has the option to present their contactless card against the Contactless
symbol when displayed on the PINpad.
If the card is removed too quickly a message

will appear on the display and the cardholder
will be asked to present the card again.
The cardholder should hold their card against the

Contactless symbol for it to be read.
Page 10
AMOUNT
PRESENT OR INSERT
CARD
9.50
Using the Menus

The Transaction Menu enables you to perform a transaction on the terminal.
At the READY prompt press the MENU button.
The first option on the list will be highlighted.
The actual options shown may differ from those shown here.
TRANSACTION MENU
Refund
Purchase with Cashback
Force Sale
PLEASE NOTE: Only three options can be displayed on the terminal screen at any one time.
Use the
keys to view the available options.
Press the GREEN button to select a highlighted option. The terminal will return to the READY display if
no option is selected within 30 seconds.
The System Menu enables you to perform an administration function on the terminal.
Select the System Menu by following the instructions below.
At the READY prompt press the MENU button until the System
Menu is displayed. Other menu options may appear before/
after depending on your configuration.
Use the
keys to view the available options and
press the GREEN button when the required option is
highlighted.
Throughout the transaction flows in this guide, all your
instructions are denoted by this unshaded display.
All instructions to be carried out by the customer on the
PINpad are denoted by this shaded display. The customer
should follow the instructions displayed by the PINpad.
SYSTEM MENU
Totals
Print Function Codes
Select Function
READY
Merchant Number
12345678
AMOUNT
55.00
PIN ****
CARDHOLDER TO KEY PIN
ENTER=OK CLEAR=RE-KEY
Re-Printing Receipts
After a transaction a customer/merchant receipt is printed, if a re-print is required press the MENU
button and a re-print of the last receipt will be printed and the user will be asked to press ENTER.
Check to ensure receipt is correct, if another re-print is required press MENU to re-print.
PLEASE NOTE: This is not the same as printing a duplicate receipts.
Page 11
Entering Letters
You may need to enter letters using your terminal. Most numeric buttons have alphabetical
characters allocated to them.

e.g. the number 2 button has A, B and C allocated to it
e.g. the number 5 button has J, K and L allocated to it
To enter a letter press the relevant number button and then the MENU button to scroll through the
letters until you select the character required. To enter the next letter you must again select the
relevant number button. To enter a space press the 0 button followed by the MENU key.
If a mistake is made when entering numbers or letters, press the YELLOW button until the
incorrect numbers or letters have been removed. Then re-key the correct entry.
Once all the numbers or letters have been entered press the GREEN button to accept the entry.
Application Selection
Some cards support multiple card schemes and during the transaction flow the customer may be
required to choose which card scheme to use. Alternatively the customer can ask you to assist them
with this.
Customer Control
If the customer wishes to select which application to use they should press the arrow key to scroll
through the options when this screen is displayed. They should then press the GREEN button to select
the appropriate application.
Terminal Displays
<Transaction Type>
Customer to Select
Method of Payment
Press ENTER to assist
PINpad Displays
SELECT:
<Application Name>
TO SKIP
ENTER TO SELECT
Merchant Control
1.
If you press ENTER to assist you will be in control of selecting the application.
Terminal Displays
<Transaction Type>
Customer to Select
Method of Payment
2.
<Transaction Type>
Pay with ?
<Application Name>
Enter=YES
Clear=NO
PINpad Displays
SELECT:
<Application Name>
TO SKIP
ENTER TO SELECT
Now press the YELLOW button to scroll through the

options and then press the GREEN button to select the
appropriate one.
(Please refer to Section 7 of this guide for instructions on how to complete a Sale Transaction.)
Page 12
6.
Starting a Transaction
IMPORTANT INFORMATION
Your terminal may be configured to start a transaction by either entering the transaction amount first or
by inserting/swiping the payment card.
If your terminal is configured to accept Contactless payments it will always expect you to enter the
transaction amount first for whichever type of transaction you are performing.
If your terminal is configured to request the card details first the customer will be required to insert
their card into the PINpad rather than the terminal. Once this is done, enter the transaction amount
and continue from the Checking Card prompt for the chosen transaction type.
PLEASE NOTE: In this guide the PINpad displays are shown alongside the terminal displays so that you
know what the customer is being asked to do.
1.
At the READY PROMPT you may be asked to Key in the amount of the sale or to insert or swipe
customer card.
Terminal Displays
SALE
Present, Insert, Swipe
Card to Continue
(or press Cancel key)
PINpad Displays
AMOUNT 9.50
PRESENT OR INSERT
CARD
If you make a mistake, press the YELLOW button and re-enter the correct amount.
If the card is a Chip card, please see Sale (Inserting a Card) in Section 7.
If the customers card is a Contactless card and is to be used for a Contactless transaction,please see
Sale (Contactless) in Section 7.
If the customers card has been swiped, please see Sale (Card Swiped) in Section 7.
7.
Sale Transactions
Sale (Inserting a Card)

1.
Customer will be prompted to insert card into the PINpad.

SALE
Insert, Swipe Card
to Continue
2.
10:00
INSERT CARD
OR
HAND CARD TO
OPERATOR
The terminal will check the card. If the customer presents a card which supports multiple card
schemes you may be required to chose which card scheme to use.(See Section 5, Application
Selection.
SALE
Checking Card
Please Wait...
PROCESSING
PLEASE WAIT
DO NOT REMOVE
CARD
Page 13
3.
4.
Your terminal may be configured to allow Cashback, if

Cashback is required press the GREEN button.
SALE
Cashback?
If Cashback is not required press the YELLOW button

and continue from step 4.
Enter = YES
If Cashback was required, enter the Cashback amount

and press the GREEN button.
PWCB
Key in Cash Amount
If Cashback is not configured, continue from step 4

below.
Clear = NO
0.00
Ask the customer to enter their PIN into the PINpad, as they do asterisks will appear on the
screen. Now press the GREEN button.
If the PIN is entered incorrectly during this process use the YELLOW button to delete and then
re-key the correct PIN.
Amount
Customer PIN entry
25.00
AMOUNT

ENTER PIN
25.00
PIN ****
Press MENU to Bypass

Amount
Customer PIN entry
ENTER TO ACCEPT
CLEAR TO CORRECT

Amount
Customer PIN entry
PIN ACCEPTED
5.
AMOUNT
PIN ACCEPTED
DO NOT REMOVE
CARD
25.00
<Transaction Result>
PLEASE WAIT
DO NOT REMOVE
CARD
The terminal will now print a receipt which the CUSTOMER must retain for their records.
Printing
CUSTOMER RECEIPT
Please Wait...
7.
25.00
The terminal will now dial for authorisation and a number of messages will appear on the screen.
SALE
AUTH CODE: nnnnn
<Acquirer Name>
6.
25.00
Please wait...
DO NOT REMOVE
CARD
Tear off the receipt and press the GREEN button to continue. Should you require a reprint of the
receipt press the MENU button.
Tear Off
CUSTOMER RECEIPT
Press ENTER if OK
Press MENU to Reprint
Page 14
Please wait...
DO NOT REMOVE
CARD
8.
You will now be prompted to remove the customers card. The terminal will then print a
MERCHANT receipt which must be kept for your records.
SALE

Please Remove Card
REMOVE CARD
Printing
MERCHANT RECEIPT
Please Wait...
Tear Off
MERCHANT RECEIPT
Press ENTER if OK
9.
Press the GREEN button and the terminal will return to the READY prompt.
PLEASE NOTE: For security reasons and depending on the terminal configuration the full card number
may not be printed on the receipts.
Sale (Contactless)
1.
2.
The customer should present their card to the Contactless symbol on the PINpad where the card
will be read.
Terminal Displays
PINpad Displays
SALE 9.50
Card to continue
AMOUNT 9.50
PRESENT OR INSERT
CARD
The terminal will now print a Merchant receipt which should be kept for your records.
Printing
MERCHANT RECEIPT
APPROVED
Please Wait ...

Tear Off
MERCHANT RECEIPT
Press ENTER if OK
Processing
Please wait...
If the customer requests a receipt this must be done before the next transaction takes place.
3.
From the READY prompt press the

key and a customer receipt will be printed. Press the
GREEN button to return to the READY prompt.
Printing
CUSTOMER RECEIPT
<IDLE DISPLAY>
Please Wait ...
Page 15
Sale (Swiping a card)

1.
The customer should hand their card to you to swipe through the terminal. Once the card has been
swiped the terminal will check the card.
Terminal Displays
SALE
Insert or Swipe Card
to Continue
2.
PINpad Displays
INSERT CARD
OR
HAND CARD TO
OPERATOR
You may be prompted to confirm the last four digits of the card number. Key in the last four
numbers from the customers card and then press the GREEN button.
Key in last 4 digits
of Card Number
PROCESSING
PLEASE WAIT
3.
The terminal will now dial for authorisation and a number of messages will appear on the screen.
SALE
AUTH CODE: nnnnn
<Acquirer Name>
4.
PROCESSING
PLEASE WAIT
The terminal will print a Merchant receipt, tear this off and ask the customer to sign it.
Printing
MERCHANT RECEIPT
PROCESSING
PLEASE WAIT
Please Wait...
Tear Off
MERCHANT RECEIPT
Press ENTER if OK
5.
Check the signature and, if it is OK, press the GREEN button and a Customer receipt will be printed.
If the signature is not OK press the YELLOW button and the transaction will be cancelled.
SALE
Signature OK?
Enter=YES
6.
PROCESSING
PLEASE WAIT
Clear=NO
The terminal will now print the Customer receipt.

Printing
CUSTOMER RECEIPT
Please Wait...
Page 16
PLEASE WAIT
7.
Pass this receipt to the customer for their records.

Tear Off
CUSTOMER RECEIPT
Press ENTER if OK
8.
PLEASE WAIT
The transaction is now complete and the terminal will return to the READY prompt.
Voice Referrals
Sometimes transactions will require you to obtain a voice referral from the Authorisation Centre.
As a security measure your terminal may have been set up to request either the swipe of the
Supervisor Card or the input of a Referral Password when this situation arises.
Please follow the process below if your terminal has been set up to ask for a Referral Password.
1.
The following screens will be displayed if the transaction gets a referral message from the
acquiring host:
<Transaction Type>
<Voice Referral Message>
<Acquirer Name>
Press CLEAR
SALE
Please remove card
for voice referral
2.
SALE
REMOVE CARD AND
HAND TO OPERATOR
The card should be removed from the terminal and handed to the operator who will be
contacting the Authorisation Centre.
REFERRAL
MID: 12345678
CALL: nnnn nnnnnnn
3.
PROCESSING
PLEASE WAIT...
PROCESSING
PLEASE WAIT
You may be asked to swipe your Supervisor card or enter your Referral Password and then press
the GREEN button to continue.
Enter Referral Password
PROCESSING
PLEASE WAIT
and then press enter

Please Wait...
Once you have spoken to the Authorisation Centre and if the transaction is authorised, press the
GREEN button to continue with the transaction. If Authorisation is declined press the YELLOW
button.
PLEASE NOTE: Please see Section 8 on how to set a Referral Password.
Page 17
If the YELLOW button is pressed, the terminal will display Not Authorised and print a Not
Authorised receipt. The terminal will then return to the READY prompt.
SALE
Authorisation given?
ENTER=YES
CLEAR=NO
SALE
Key in Auth. Code

<Auth Code>
4.
If the GREEN button is pressed, enter the authorisation code provided by the Authorisation Centre
and press the GREEN button. The terminal will now print the receipts and then return to the READY
prompt.
8.
Setting the Referral Password
Function 23 will allow you to set and change the Referral Password.
1.
At the READY prompt, press the MENU button twice.
2.
Use the
key highlight the SELECT FUNCTION option
and then press the GREEN button.
3.
Enter the number 23 and then press the GREEN button,

the terminal will ask you to swipe the Supervisor card
or key in your Supervisor code.
4.
Now press the GREEN button to select the option to Set

the Referral Password.
SYSTEM MENU
Totals
Select Function
EFT
Set Referral Password?
Enter=YES
Clear=NO
Pressing the YELLOW button will return the terminal to the READY prompt.
If this is the first time the Password has been set please enter 0000 and then press the GREEN button.
2.
If the code is to be changed, key the current code and

then press the GREEN button.
Enter Current
Referral Password?
3.
Enter a new Referral Password and then press the

GREEN button.
Enter New
Referral Password?
4.
Re-key the new Referral Password to confirm and then

press the GREEN button.
The terminal will print a receipt to confirm the Password has been changed and will return to the READY
prompt.
Page 18
Confirm New
Referral Password?
9.
1.
Refunds
At the READY prompt, press the MENU button.

Use the
key to highlight REFUND and then press
the GREEN button.
2.
TRANSACTION MENU
Refund
Purchase with Cashback
Force Sale
Either key in the amount of refund transaction and then press GREEN button or swipe/insert card
into the PINpad and then key in the refund amount.
Terminal Displays
PINpad Displays
REFUND
to continue
PROCESSING
PLEASE WAIT
REFUND
Key in Amount:
0.00
<IDLE DISPLAY>
If performing a swiped transaction, your terminal may prompt you to enter the last four digits of the
card number. If so, key in the last four digits of the customers card number and press the GREEN button.
The terminal will check the card. If a customer presents a card that supports multiple card schemes, you
may be required to choose which card scheme to use. You may then be asked to remove the card and
the transaction will continue as per a signature verified sale.
(Please refer to Section 7 of this guide for instructions on how to complete a Sale Transaction.)
PROCESSING
PLEASE WAIT
DO NOT REMOVE
CARD
SALE
Checking Card
Please Wait...
Contactless Refund
To perform a Contactless Refund Amount Entry First must be enabled; the card scheme must be
configured to allow it and the transaction amount must be below the maximum contactless
transaction limit:
Note: A Contactless Refund may be performed either by using credit/debit cards (if configured) or
any other contactless devices such as Fobs or Mobile Telephones.The following screens will only be
displayed if the transaction amount is below the Contactless transaction limit:
Terminal Displays
PINpad Displays
If the transaction value is below the maximum Contactless Limit the following screen will be displayed:
REFUND
Key in the amount
<IDLE DISPLAY>
0.00
Page 19
3.
If the value is above the Contactless Limit you will be asked to swipe/insert card. Normal card
checks will be performed.
If refunds are supervisor protected then you will be asked to swipe the supervisor card or key in
the supervisor code.
REFUND
Card to Continue
5:00
AMOUNT 9.50
PRESENT OR INSERT
CARD
10. Purchase with Cashback

This option only needs to be selected when your terminal is configured to accept gratuities and you
may wish to provide Cashback instead of adding a Gratuity. Selecting this option will result in the
transaction being carried out with Cashback instead of Gratuity
PLEASE NOTE: Only certain types of debit cards allow Purchase with Cashback.
1.

Using the
key, highlight PURCH. WITH CASHBACK
and then press the GREEN button
2.
Key in the amount of the sale and press the GREEN button.
Terminal Displays
PWCB
Key in Sale Amount:
3.
PINpad Displays
<IDLE DISPLAY>
0.00
Either key in the cashback amount and then press GREEN button or swipe/insert card in the
terminal and then key in the cashback amount.
PWCB
Key in Cash Amount:
4.
TRANSACTION MENU
Refund
Purch.
with Cashback

Force Sale
0.00
PROCESSING
PLEASE WAIT
DO NOT REMOVE
CARD
The transaction will now continue as a normal sale transaction.

(Please refer to Section 7 of this guide for how to complete a Sale Transaction.)
PLEASE NOTE: For securinty reasons and depending on the configuration of your terminal the full
card number may not be prined on receipts.
Page 20
11. Cash Advance

Please note that this option is only available for certain types of business. Please contact Customer
Services for further information.
PLEASE NOTE: Only certain types of cards allow Cash Advance.
1.

Using the
key, select Cash Advance and then
2.
Either key in the transaction amount and then press GREEN button or swipe/insert card in the
terminal and then key in the transaction amount.
Terminal Displays
CASH ADVANCE
Key in Amount:
0.00
3.
TRANSACTION MENU
Refund
Cash Advance
Force Refund
PINpad Displays
<IDLE DISPLAY>
If performing a swiped transaction, your terminal may prompt you to enter the last four digits
of the card number. If so, key in the last four digits of the customers card number and press the
GREEN button.

(Please refer to Section 7 of this guide for how to complete a Sales Transaction.)
12. Purchase with Gratuity (Restaurants)

Please Note: This option is only available for certain types of business. Please contact Customer
1.
At the READY prompt, either key in the transaction amount and then press GREEN button or
swipe/insert the card in the terminal to start transaction. The terminal will check the card.
Terminal Displays
SALE
Checking Card

Please Wait...
PINpad Displays
PROCESSING
PLEASE WAIT
card number. If so, key in the last four digits of the customers card number and press the GREEN
button.
2.
Your terminal may prompt you to enter the Waiter ID. If so, enter the relevant Waiter ID and press
the GREEN button. You may also be prompted to enter the table number.
(Please see Section 27 for more information on Waiter IDs).
SALE
Key in <Waiter Prompt>
<Waiter ID>
PROCESSING
PLEASE WAIT
DO NOT REMOVE
CARD
Page 21
3.
The customer will be asked to confirm the amount. They should press the GREEN button to accept
or the YELLOW button to reject.
Amount 20.00
Customer to
confirm Amount
AMOUNT 20.00
ENTER TO Accept
CLEAR TO Reject
If the customer rejects the amount you will be prompted to press the GREEN button to re-enter
the amount.
4.
The customer will be asked if they want to add a gratuity; if they do not want to do this they
should press the YELLOW button and the transaction will continue from step 8.
If the customer wishes to add a gratuity they should press the GREEN button.
Amount 20.00
Customer to
Add a GRATUITY
5.
AMOUNT 50.00
Add a GRATUITY?
Enter=YES
Clear=NO
The customer will now be prompted to key in the gratuity amount and then press the GREEN
button.
Amount 20.00
Customer to
Add a GRATUITY
GRATUITY

ENTER TO ACCEPT
CLEAR TO CORRECT
5.00
If terminal is configured for Gratuity percentage contine from step 6. If terminal is configured for
Gratuity amount entry continue from step 7.
6.
If Gratuity with percentage is enabled the following screen will be displayed, either select a Fixed
Percentage from the available options or select OTHER to key in the amount.
Gratuity Percentage
15%
210 %
315 %
420 %
5Other
7.
The customer will then be prompted to confirm the total transaction amount.
TOTAL
Customer to
Confirm Total
8.
25.00
TOTAL

ENTER To Accept
CLEAR To Reject
25.00
The customer will be prompted to enter their PIN. Once the PIN has been entered, the customer
should press the GREEN button to confirm.
Amount
Customer PIN entry
25.00
AMOUNT

ENTER PIN
PLEASE NOTE: Removing the card at this point will VOID the transaction.
Page 22
25.00
The terminal will dial for authorisation and a number of messages will appear on the screen.
If authorisation is obtained the terminal will print the customers receipt. Press the GREEN button if the
receipt has printed correctly. If the receipt is not correct, press the MENU button for a
re-print. The customer will be prompted to remove their card.
The terminal will then print a MERCHANT receipt which should be retained for your records.
If the receipt has printed incorrectly, press the MENU button and the receipt will be re-printed. Press the
GREEN button and the terminal will return to the READY prompt.
13. Refund with Gratuity

1.
2.
Using the
key, highlight REFUND and then press
the GREEN button
3.
Key in the total amount of the transaction to be refunded, including any gratuity and press the
GREEN button. Alternatively insert/swipe the customers card and then key in the total amount.
Terminal Displays
REFUND
Key in TOTAL Amount
4.
TRANSACTION MENU
Refund
Sale
Force Sale
PINpad Displays
0.00
<IDLE DISPLAY>
You may be asked to either present, insert or swipe the customers card through the
terminal. You may be prompted to swipe your supervisor card or enter your supervisor code.
REFUND
to continue
INSERT CARD
OR
HAND CARD TO OPERATOR
button.
You may be prompted to swipe the Supervisor Card or enter the supervisor code through the terminal.
5.
If a gratuity has been added, press the GREEN button. If no gratuity has been added, press the
YELLOW button.
REFUND
<Gratuity String> Added?
Enter = YES
PROCESSING
PLEASE WAIT
Clear = NO
Page 23
5.
If a gratuity has been added, enter the amount of the gratuity and press the GREEN button.
REFUND
Key in <Gratuity String>
0.00
6.
PROCESSING
PLEASE WAIT
You may be asked to key in the Waiter ID from the original transaction and press the GREEN
button.
REFUND
Original Waiter ID:
PROCESSING
PLEASE WAIT
The transaction will now proceed as a normal refund transaction.

NOTE: Please see Section 9 for information on how to complete a Refund Transaction.
14. Pre-Authorisation
PLEASE NOTE: this option is only available for certain types of business. Please contact Customer
Where there is the likelihood of a large value transaction, such as a hotel or car hire bill, a
pre-authorisation transaction for the expected value can be made. If, following a pre-authorisation
transaction, the value of the transaction increases (e.g. as a result of an extended stay at a hotel)
a further pre-authorisation may be required.
1.

Using the
key, highlight PRE AUTH and then press
the GREEN button.
2.
TRANSACTION MENU
Refund
Purch. with Cashback
Pre-Auth
Key in the amount of the transaction and press the GREEN button, or insert/swipe the customers
card and then key in the transaction amount.
Terminal Displays
PRE-AUTH
Key in Amount:
0.00
PINpad Displays
PROCESSING
PLEASE WAIT
DO NOT REMOVE
CARD
button.
3.
The transaction will now continue as a normal Sales Transaction.

PLEASE NOTE: (Please refer to Section 7 for information on how to complete a Sales Transaction.)
Page 24
15. Completion
PLEASE NOTE: If the final bill is more than the total pre-authorised amount, a further pre-authorisation
may be required for the difference which must be obtained prior to carrying out the completion
transaction.
The following procedure will complete a pre-authorised transaction when the final amount is
confirmed with the customer.
1.

Using the
key, highlight COMPLETION and then
press the GREEN button
2.
TRANSACTION MENU
Pre-Auth
Completion
Cash Advance
Key in the amount of the transaction and press the GREEN button, or insert/swipe the customers
card and then key in the transaction amount.
Terminal Displays
COMPLETION
Key in Final Amount:
0.00
PINpad Displays
PROCESSING
Please wait...
DO NOT REMOVE
CARD
card number. If so, key in the last four digits of the customers card number and press the GREEN button.
3.
You will then be prompted to enter the last Pre-Authorised code and press the GREEN button.
COMPLETION
Key in Last Pre-Auth Code:
PROCESSING
PLEASE WAIT
DO NOT REMOVE
CARD T

(Please refer to Section 7 for information on how to complete a Sale Transaction.)
16. Key Entering Card Details and Mail Order

Transactions
You may need to key enter a customers card details if their card is faulty or if you are entering a mail
order transaction where the customer is not present.
A. Mail Order Transactions:
Begin at Step 1 if you are performing a Mail Order Transaction.
B. Card Read Failure or Key Card Number:
Begin at Step 2 if:
Page 25
You have swiped a customers card at the READY prompt and the terminal displays CARD
READ FAILURE
OR
If you have selected the Sale option from the Transaction menu and unsuccessfully
swiped the card three times, and the terminal displays Key in Card Number.
1.
2.
Use the
keys to highlight SALE and then press
the GREEN button.
3.
Key in the amount of the transaction and then press

the GREEN button, or key in the customers card
number when you see this prompt. The card number
will be displayed as it is keyed in.
TRANSACTION MENU
REFUND
Sale
Purch. with Cashback
<transaction type>
to continue
The terminal will check the card number.

4.
Key in the card expiry date and press the GREEN button.
<transaction type>
Key expiry date MMYY
5.
You may be asked to enter the start date or issue

number from the card. Enter them as they appear on
the card and press the GREEN button.
<transaction type>
Key start date MMYY
<transaction type>
Key in issue number
5.
6.
7.
If the customer is present, press the GREEN button. If

this is a mail order transaction, press the YELLOW button
and proceed from step 9 below.
If not entered earlier in the process, key in the amount

of the transaction and press the GREEN button. The
terminal will now dial for authorisation. The
authorisation code will be displayed. Press the GREEN
button.
A receipt will now be printed. Obtain the customers
signature. If the signature is OK, press the GREEN
button. If it is not, press the YELLOW button and the
transaction will be voided.
Page 26
<transaction type>
Is customer present?
Enter = YES
Clear = NO
<transaction type>
Key in Amount:
0.00
SALE
Signature OK?
Enter = YES
Clear = NO
8.
The signed receipt should be kept for your records. The

terminal will now print a receipt for the customer.
Pass the receipt to the customer and the transaction is
complete.
9.
If this is a mail order transaction, the YELLOW button

will be pressed when asked if the customer is present.
If not entered earlier in the process, key in the amount
of the transaction and press the GREEN button.
<transaction type>
Is customer present?
Enter = YES
Clear = NO
IF YOUR TERMINAL IS CONFIGURED FOR CSC/AVS (A CARDHOLDER VERIFICATION SERVICE) PROCEED AS

FOLLOWS.
If you see this prompt, key in the 3 digit security code,
which can be found on the signature strip on the back of the
customers card. Now press the GREEN button.
<transaction type>
Key in Security Code:
PLEASE NOTE: The security code for American Express cards is a four digit code and can be found on the
front of the card.
Your terminal will then prompt you to do the following:
Enter the numeric digits from the customers Post Code, (i.e
EH11 9YE would be entered 119) and then press the GREEN
button.
Key in Numerics From

The Post Code:
Enter the customers house number, ( i.e Flat 5, 29 High

Street would be entered 529) and then press the GREEN
button.
Key in First Five Digits

Of the Address:
10. The terminal will now dial out for authorisation and the
authorisation code will be displayed. Press the GREEN
button.
<transaction type>
AUTH CODE: nnnnn
<Acquirer Name>
press ENTER
The terminal will display the results of the address check. The result will be printed on the receipts.
The security message will advise the response for any information entered at the Security Code,
Address and Post Code prompts.
Message Text
Result
ALL MATCH
ALL DATA ENTERED IS CORRECT
SEC CODE MATCH ONLY
ONLY THE SECURITY CODE IS CORRECT
ADDRESS MATCH ONLY
ONLY THE ADDRESS IS CORRECT
NO DATA MATCHES
NONE OF THE DATA ENTERED IS CORRECT
DATA NOT CHECKED
THE DATA HAS NOT BEEN CHECKED
Page 27
11. To accept the transaction press the GREEN button and

a customer receipt will be printed. Press the GREEN
button again and this will print a copy of the receipt for
your records.
AUTH CODE:
nnnnn
<security message>
Press ENTER to Accept
Press CLEAR to Decline
To decline the transaction press the YELLOW button and a void receipt will be printed for the customer.
Press the YELLOW button again and a void receipt will be printed for your records.
17. Reversal
You can reverse the last previously authorised Sale or Refund transaction provided the reversal is
carried out within 30 seconds of completing the original transaction.
1.
2.
Using the
key, highlight REVERSAL and then press
the GREEN button
3.
The terminal will dial the authorisation centre and display the message CONNECTION MADE.
The terminal will now confirm the reversal is successful and print a receipt.
TRANSACTION MENU
Refund
Duplicate Receipt
Reversal
Tear off the receipt and give this to the customer as a copy of the transaction. Press the GREEN
button.
The terminal will now print a copy of the receipt for you to retain for your records. Press the GREEN
button and the terminal will return to the READY prompt.
If a re-print is required press the MENU button.
18. Verify Account

1.
Press the MENU button and then use the arrow keys
to highlight the transaction type from the transaction
menu and then Press GREEN.
2.
Insert or Swipe Card the customers card.
3.
Ask the customer to enter their PIN into the PINpad, as

they do asterisks will appear on the screen. Now press
the GREEN button.
4.
The terminal will contact the acquirer to verify that this

is a valid account.
Page 28
TRANSACTION MENU
Verify Account
Pre-Auth
Refund
VERIFY ACCOUNT
to continue
( or press Cancel key )
Amount 0.00
PIN: ****
Cardholder to key PIN
Enter=OK
Clear=REKEY
Amount 0.00
PIN ACCEPTED
RETURN TERMINAL
Do NOT Remove Card
19. PIN Entry Failure

If an incorrect PIN has been entered the PINpad and terminal will display INCORRECT PIN.
1.
The cardholder has three attempts to enter their PIN

after which the terminal will display the message: PIN
TRIES EXCEEDED
INCORRECT PIN

ENTER PIN
2.
If this message is displayed the customer will need to

contact their card issuer.
PIN TRIES
EXCEEDED
DO NOT REMOVE CARD
3.
The transaction will continue and seek authorisation

with a signature verification. Press the GREEN button to
continue the transaction.
PIN TRIES EXCEEDED

Press ENTER to
Continue with
Signature
20. Cancelling Transactions

1. CANCELLING BEFORE AUTHORISATION
A transaction can be cancelled at any time before authorisation has been obtained.
Press the RED button. The terminal will display CANCELLED and print a receipt for the customer which
will be marked as cancelled.
Then press the GREEN button and the terminal will print a merchant receipt for your records.
Press and GREEN button again and the terminal will then return to the READY prompt.
2. CANCELLING AFTER AUTHORISATION BUT BEFORE COMPLETION
When carrying out a swiped transaction and the transaction requires cancelling after authorisation has
been obtained, but before the transaction has been completed, press the YELLOW button at the
SIGNATURE OK prompt to select NO and reject the signature.The transaction will be cancelled and a
void receipt will be printed.
3. CANCELLING AFTER COMPLETION OF A TRANSACTION
If the transaction requires cancelling after the transaction has been completed a REVERSAL or a REFUND
will need to be performed. (Please refer to Section 16 for Reversal or Section 8 for Refund)
NOTE: Reversal transactions can only be carried out within 30 seconds of the transaction taking place.
4. CANCELLING THE TRANSACTION BY THE CUSTOMER
If the customer selects to cancel a transaction, they will be asked to confirm if they wish to do so. The
customer will only be prompted to remove their card after the cancellation receipt has been printed. If
the receipt is correct press the GREEN button. A merchant cancellation receipt will then be printed.
Page 29
21. Clearing Mistakes

If a mistake is made when entering numbers or letters, press the YELLOW button until the incorrect
numbers or letters have been removed or press the RED button to erase all input. Now re-key the
correct entry.
22. Printing Duplicate Receipts

1.

Using the
key, highlight DUPLICATE RECEIPT and
then press the GREEN button.
2.
Press the GREEN button to print a duplicate receipt. It

is not an exact copy of either a customer or merchant
receipt and has Duplicate Receipt printed on it.
TRANSACTION MENU
Print Chip Data
Reversal
Duplicate Receipt
EFT
Duplicate Receipt?
Enter = YES
Clear = NO
23. X and Z Totals

X Totals can be printed at any time throughout the day and give a sub-total of all transactions
performed. X totals do not reset the totals within the terminal.
Z Totals show the total of all transactions processed through the terminal for each card company since
the last Z Totals were performed. Once Z Totals have been completed the totals within the terminal are
reset to zero. X Totals will also be reset.
Z Totals are not connected to your Banking totals.
1.
At the READY prompt, press the MENU button twice. The

TOTALS option will be highlighted and then press the
GREEN button and the TOTALS MENU will be displayed.
2.
Use the
keys and press the GREEN button when
the X-TOTALS is highlighted.
3.
You will then be asked to swipe your Supervisor Card or

enter your Supervisor code.
4.
Press the GREEN button to proceed or the YELLOW

button to cancel.
5.
The terminal will print the report. Press the MENU

button if you wish to reprint the report. If not, press the
GREEN button and the terminal will return to the READY
prompt.
Page 30
SYSTEM MENU
Totals
Select Function
TOTALS MENU
End-of-Day Banking
Z-Totals
X-Totals
EFT
X-Totals? (or Z-Totals?)
Enter = YES
Clear = NO
Tear Off
TOTALS RECEIPT
Press ENTER if OK
Press Menu to Reprint
24. Waiter Totals

1.

TOTALS option will be highlighted and then press the
GREEN button and the TOTALS menu will be displayed.
2.
Use the
buttons to view the available options
and press the GREEN button when the Waiter Totals
option is highlighted.
3.
You will then be asked to swipe your Supervisor Card

or enter your Supervisor code.
4.
Press the GREEN button to print the totals.
SYSTEM MENU
Totals
Select Function
TOTALS MENU
Z-Totals
X-Totals
Waiter Totals
EFT
Print Waiter - Totals
Enter = YES
5.
Clear = NO
To reset the Waiter Totals press the GREEN button and

the totals will be reset.
WAITER TOTALS
Reset Waiter - Totals?
The terminal will now return to the READY prompt.
Enter = YES
Clear = NO
25. End-of-Day Banking

Banking should be carried out at the end of each business day once the last customer has left the
premises. This is to make checking credits and reconciliation with your bank statements easier.
PLEASE NOTE: If your acquirer has set a cut-off time for end-of-day banking, please note the following:
To ensure that your statement totals balance, it is important that you carry out your End-of- Day Banking before the cut-off time set by your acquirer. For information regarding these times please contact
Customer Services.
1.

TOTALS option will be highlighted. Press the GREEN
button and the TOTALS MENU will be displayed.
2.
Use the
key to highlight END of DAY and press
the GREEN button.
3.
You will then be asked to swipe your Supervisor Card or

enter your Supervisor code.
4.
Press the GREEN button to proceed.
SYSTEM MENU
Totals
Select Function
TOTALS MENU
End-of-Day Banking
Z-Totals
X-Totals
EFT
End-of-Day Banking?
Enter = YES
Clear = NO
Page 31
5.
You will now have the choice of selecting totals for ALL
card types or selecting those card types you wish to
bank.
Press the GREEN button to reconcile ALL card types and
the terminal will contact each acquirer before printing
the report or press the YELLOW button to select the
acquirers you wish to reconcile.
Select card types to be

banked
Press ENTER for ALL
Press CLEAR to SELECT
PLEASE NOTE: This screen will only be displayed if your terminal is set up with more than one acquirer.
6.
You will now be shown a list of the individual acquirers.

Press the GREEN button to reconcile an acquirer or press
the YELLOW button if you do not want to reconcile a
particular acquirer.
End-of-Day Banking
Bank <acquirer>
Enter = YES
Clear = NO
Once the desired acquirers have been selected, the terminal will dial the selected acquirers. You will be
prompted to wait while the terminal prints a banking report.
After all acquirers have been banked, tear off the receipt and press the GREEN button.
The terminal will return to the READY prompt.
PLEASE NOTE: If Stored or Session Totals Not Agreed is printed on your End-of-Day receipt, please
contact Customer Services.
26. Entering Function Codes

There may be occasions when you have further requirements of your terminal. These can be met
through the use of Function Codes.
1.
2.
Use the
buttons to view the available options
and press the GREEN button when the SELECT FUNCTION
option is highlighted.
3.
Key enter the function code required and then press the
GREEN button.
SYSTEM MENU
Totals
Select Function
Once the function code has been entered, follow the prompts displayed by the terminal. You may be
prompted to swipe your Supervisor Card or key in your Supervisor code.
The following codes are available for you to use:
CODE
TITLE
DESCRIPTION
16
Print Transaction Log
Refer to Section 29
23
Setting Referral Password
Refer to Section 8
30
Set Date/Time
Refer to Section 28
40
Waiter Setup
Refer to Section 27
Page 32
27. Waiter IDs (Restaurants)

Default Waiter 0
A default waiter, Waiter 0: SHARED will be created automatically by the terminal. This can be used if
you do not want to create individual Waiter IDs.
All Sale transactions with gratuity will add tips/gratuities to this waiter without the need for a waiter ID
to be entered during transaction processing.
The total of all Waiter 0 tips/gratuities will be printed as part of the Waiter Totals Report showing the
total value of tips/gratuities performed.
Adding an Individual Waiter ID
Your terminal can be configured to recognise individual Waiter IDs. These make it possible to
identify which staff member has dealt with the transaction. The Waiter ID will be printed on the receipt.
1.
At the READY prompt press the MENU button twice.
2.
Using the
key highlight the Select Function
option and then press the GREEN button.
3.
Enter the number 40 and then press the GREEN button.

Swipe your Supervisor Card or enter your Supervisor
code. If you want to proceed to the Waiter Setup menu,
press the GREEN button. If not, press the YELLOW button
to return to READY prompt.
4.
Using the
GREEN button.
key, highlight Add and then press the
SYSTEM MENU
Totals
Select Function
EFT
Waiter Setup
Enter = YES
Clear = NO
WAITER SETUP
Add
Delete
Print
Change Name
Delete All
Create Defaults
5.
Your terminal will automatically allocate the next

available Waiter ID. Key in the text/name description
and press the GREEN button (this field is limited to 10
characters).
ADD Waiter
Code nn
Key in Waiters Name
aaaaaaaaaaaa
(Please refer to Section 5 for instructions on how to Enter Letters).

A total of 99 waiters can be added.
Deleting a Waiter ID
Follow steps one to five above and select Delete from the WAITER SETUP menu, now proceed as
follows:
Page 33
1.
Key in the Waiter ID code that is to be deleted and then

DELETE Waiter
Key in Code to Delete
2.
If you want to proceed to delete the Waiter, press the

GREEN button.
If not, press the YELLOW button.
nn
DELETE Waiter nn
<name>
Enter = YES
Clear = NO
Changing a Waiter ID
Follow steps one to five of Section 27 (Adding an Individual Waiter ID) and select Change Name from
the WAITER SETUP menu. Now proceed as follows:
1.
2.
To change a Waiter Name, key in the Code of the

Waiter that requires change and then press the GREEN
button.
Amend the Waiter Name by using the RED and YELLOW
buttons to erase letters. Press the GREEN button and
the terminal will return to the Waiter Setup Menu.
CHANGE Name
Key in Code to Change

nn
CHANGE Name nn
Key in Waiters Name
<existing name>
(Please refer to Section 5 for instructions on how to Enter Letters.)

Creating Default IDs
When using the Create Defaults option, the terminal automatically creates numbered Waiters from
1-99 instead of named Waiters.
Follow steps one to five of Section 27 (Adding an Individual Waiter ID) and select Create Defaults from
the WAITER SETUP menu.
If Waiters do not yet exist
When asked whether you would like to create
defaults on your terminal, press the GREEN button to accept.
To decline, press the YELLOW button.
CREATE Defaults
Are You Sure?
Enter = YES
Clear = NO
If Waiters already exist

If Default Waiters exist on your terminal and you wish to add
a named waiter, this screen will be displayed. You MUST
delete a Default Waiter before a named waiter can be
added. Press the GREEN button.
Waiters Already Exist

Delete ALL if you wish
to remove existing IDs
Press ENTER
28. How to Change the Date and Time

The terminal has a built in clock which maintains the current date and time. If necessary you can also
change the date and time manually. Please note: This will need to be done twice a year when the
clocks change.
Page 34
1.
At the READY prompt press the MENU button twice.
2.
Using the
key highlight the SELECT FUNCTION
3.
Key enter the number 30 and press the GREEN button.

You will then be asked to swipe the Supervisor Card or
key in your Supervisor code.
4.
The current date will be displayed. Re-key the correct

date and press the GREEN button.
SET DATE/TIME
Enter Current Date
The current time will be displayed. Re-key the correct

time and press the GREEN button.
SET DATE/TIME
Enter Current Time
The terminal will return to the READY prompt.
5.
SYSTEM MENU
Totals
Select Function
Key in Function Code

dd/mm/yy
hh:mm
29. How to Print a Transaction Log

This function allows you to print a log of your last 100 transactions, should the need arise for
example to check any financial discrepancies.
1.
2.
Using the
key highlight the SELECT FUNCTION
3.
Key enter the number 16 and press the GREEN button.

You will then be asked to swipe the Supervisor Card or
key in your Supervisor code.
4.
To print a transaction log for the selected acquirer, press

the GREEN button. If not, press the YELLOW button.
SYSTEM MENU
Totals
Select Function
Key in Function Code


<Acquirer Name>?
Enter = YES
5.
6.
Press the GREEN button again and the transaction

log for that acquirer will be printed. It will show the
previous 20 transactions for that acquirer. Step 3 and 4
should be repeated for each acquirer.
Clear = NO

Continue?
Enter = YES
Clear = NO
Once all have been printed, press the GREEN button

and the terminal will return to the READY prompt.
Page 35
30. How to Change a Paper Roll

1.
2.
3.
4.
1. Hold the terminal securely in one hand. With the other hand using two fingers to lift the printer
cover release as shown.
2. Unstick the end of the new roll. Leaving the end free, hold the paper roll and carefully place into the
printer compartment.
3. Holding the free end of the paper and your terminal, close the printer cover carefully and push firmly
until it locks.
4. While your terminal is displaying the idle screen, press and hold the YELLOW button to ensure that
the paper feeds correctly. Only paper rolls that are 57mm wide and 40mm in diameter can be used in
your terminal. Attempting to fit rolls of a different size may damage your terminal.
31. Insuring the Terminal

Although you rent your terminal for a monthly charge it is strongly recommended that you insure the
terminal against loss or damage to a value as recommended by your acquirer.
32. Security Warning Notice

This terminal is used for the secure transfer of funds using credit and debit cards. As such it is designed
as a high security device.
Should you suspect that the terminal might have been removed, stolen or apparently modified or
replaced then you should advise your Bank immediately and stop using the terminal until advised
by the Bank accordingly. This is to protect both your business and also the persons who have or will
continue to use your terminal.
Please be vigilant at all times and check your terminal regularly.
Page 36
33. Helpful Hints

Terminal Tips

Your terminal unit should be left in your retail premises and plugged into a 24 hour power supply
and telephone line at all times.
If the terminal display is blank, ensure the terminal is plugged into the power supply.
If you have poor quality printing, change the paper roll.
Keep your Supervisor card in a secure place. Anyone with access to this card or code may perform
unauthorised refunds. If your terminal is configured for supervisor code do NOT write this down or
give this to anyone.
Financial Tips

Always check you have keyed in the correct amount before going ahead with the transaction.
If you are referred for an authorisation code, read the amount from the slip to ensure you have
the correct amount (It has been known for the amount of 2,000.00 to be keyed instead of 200.00;
A code is then obtained for the 200.00 but the cardholder is debited for the keyed amount of
2,000.00)
Always check your bank statement on a regular basis to ensure you are receiving your credits and
that the amounts are correct.
Remember to reconcile the terminal each day as this will generate all the funds to your bank
account.
You will not be credited with Z Totals as these are running totals for your records and do not
generate funds to your account.
Keep your copy transaction slips in a safe place. There may be occasions when you are asked to
provide copies of these. Please ensure that Refund transactions show as REFUND ACCEPTED.
If the terminal prints the message Totals not Agreed when you carry out your End of Day
Banking, please contact the Helpdesk.
If Stored is printed on your End Of Day report please contact the Helpdesk.
Page 37
34. Miscellaneous Prompts

Below are explanations for some of the common prompts displayed by the terminal.
PROMPTS
Call Auth centre
CAUSE/REASON
REMEDY
Assistance required.
Call the Authorisation Centre on the number displayed by

the terminal.
Once you have spoken to the Authorisation Centre press
the GREEN button and follow the prompts displayed by
the terminal.
Call Helpdesk
Please contact your Helpdesk.
Not Authorised
The card issuer has

declined to authorise
the transaction.
Ask the customer to pay by some other means and press

the YELLOW button.
Referral
Call the Authorisation Centre on the number displayed by

the terminal. When the call is answered quote the referral
message and your Merchant Number.
Unable to Authorise
Transaction declined
by the card.
Ask the customer to pay by some other means and press

the YELLOW button.
Unable to Connect
Terminal not
connecting to host
via a telephone line.
Check the telephone line is connected properly. Call the

Helpdesk for guidance.
DIV434692A
COPYRIGHT 2012 Ingenico UK Ltd
ALL RIGHTS RESERVED
Date: July 2012
Released for UT4.13.10
Page 38
Ingenico
Ridge Way
Donbristle Industrial Park
Dalgety Bay
Fife
KY11 9JU
Part Number: DIV434692A_Cover

Ingenico Ict220 Users Manual 120304

Uploaded by

Copyright:

Available Formats

Ingenico Ict220 Users Manual 120304

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ingenico Ict220 Users Manual 120304

Uploaded by

Copyright:

Available Formats

Terminal User Guide

iCT220 & ML30

Important Safety Instructions

General Safety Information

Do read and understand the instructions before using the equipment.

External Power Supply

Systems to which the Modem may be connected

The Public Switched Telephone Network (PSTN).

and complies with the following harmonised standards:

Electrical safety of data processing

Radio electric disturbance characteristics

Immunity characteristics limits and

Installing the Terminal

Installing the Terminal via PSTN

Dual Comms Mode

You should use the

and then press ENTER

and then press ENTER

Key in your Merchant Number and press the GREEN button.

Installing the Terminal via Ethernet (IP)

Dual Comms Mode

You should use the

Key in your Merchant Number and press the GREEN button.

and then press ENTER

Using the Terminal

Inserting a Chip Card into the PINpad

Inserting a Chip Card into the Terminal

Using a Card with the Contactless Reader

If the card is removed too quickly a message

The cardholder should hold their card against the

Using the Menus

keys to view the available options.

e.g. the number 2 button has A, B and C allocated to it

e.g. the number 5 button has J, K and L allocated to it

Now press the YELLOW button to scroll through the

Sale (Inserting a Card)

Customer will be prompted to insert card into the PINpad.

Your terminal may be configured to allow Cashback, if

If Cashback is not required press the YELLOW button

If Cashback was required, enter the Cashback amount

If Cashback is not configured, continue from step 4

and then press ENTER

Press MENU to Bypass

Press MENU to Bypass

Please Wait ...

From the READY prompt press the

Please Wait ...

Sale (Swiping a card)

and then press ENTER

The terminal will now print the Customer receipt.

Pass this receipt to the customer for their records.

and then press enter

Setting the Referral Password

At the READY prompt, press the MENU button twice.

Enter the number 23 and then press the GREEN button,

Now press the GREEN button to select the option to Set

If the code is to be changed, key the current code and

Enter a new Referral Password and then press the

Re-key the new Referral Password to confirm and then

At the READY prompt, press the MENU button.