JSDA series

AC SERVO SYSTEM
Instruction Manual

Warning and Alert:

Warning

Do not proceed to the assembly of the line while electrifying.

Circuit & change components between entering shutting down the power supply and stopping
showing CHARGE LED light of the Servo driver.

The output of Servo drive [U, V, W] must NOT touch the AC power.

Alert

Install the fan if the temperature around is too high while the Servo driver is installed in the
Control Board.

Do not proceed to the Anti-Pressure-Test to the Servo driver.

Confirm the quick stop function is available before operate servo drive.

Matching up machine to change the user parameter setting before machine performs. If there is
no according correct setting number, it could lead to out of control or breakdown.

Safety proceeding:
Check the covering letter detail before installing, running, maintaining and examining. Furthermore, only
the profession-qualified people can proceed to the line-assembly.
Safety proceeding in the covering letter discriminate between Warning&Alert.

Alarm

Indicating the possibility dangerous situation. It could cause the death or serious
damage if being ignored.

Indicating the possibility dangerous situation. It could cause smaller or lighter human

Warning

injured and damage of equipment.

Read this covering letter detail before using Servo driver.

First of all, thank you for using TECO Servo Driver JSDA Series (JSDA for short) and Servo Motors.
JSDA can be controlled by digital board or PC, and provide excellent performance for a wide range of
applications and different requirement from customers.
Read this covering letter before using JSDA. Contents of the letter comprises:

Servo System checking, installing and procedure of assembly line.

Controller procedure for digital board, status displaying, unusual alarm and strategy explanation.

Servo System control function, running testing and procedures adjusted.

Explanation for all parameter of Servo Driver.

Standard specification of JSDA Series.

In order to daily examine, maintain and understand the reason of unusual situation and handle strategy,
please put this covering letter in safe place to read it anytime.
P.S: The end user should own this covering letter, in order to make the Servo Driver bring the best
performance .

ii

Contents
Chapter 1

Checking and Installing

1-1 Checking Products ..........................................................................................................................1-1

1-1-1 Confirming with Servo Drives ..............................................................................................1-1
1-1-2 Confirming with Servomotors..............................................................................................1-2
1-2 Surface and Panel Board ................................................................................................................1-3
1-3 A Brief Introduction of Operation for Drives.................................................................................1-5
1-4 Conditions for Installation of Drives..............................................................................................1-6
1-4-1 Environmental Conditions....................................................................................................1-6
1-4-2 Direction and Distance..........................................................................................................1-7
1-5 Conditions for Installation of Servomotors ..................................................................................1-8
1-5-1 Environmental Conditions....................................................................................................1-8
1-5-2 Method of Installation ...........................................................................................................1-8
1-5-3 Notice for in stall motor ........................................................................................................1-9

Chapter 2

Wiring

2-1 Basic Wiring for Servo System ......................................................................................................2-1

2-1-1 Wiring for Main Circuit and Peripheral Devices .................................................................2-1
2-1-2 Wiring for Servo Drives.........................................................................................................2-2
2-1-3 Specifications of Wiring........................................................................................................2-3
2-1-4 Motor Terminal Layout ..........................................................................................................2-4
2-1-5 Typical Wiring for Motor and Main Circuit ..........................................................................2-6
2-1-6 TB Terminal ............................................................................................................................2-7
2-1-7 Wiring for Mechanical Brake. ................................................................................................2-8
2-1-8 Breaker/Fuse/Noise Filter Specification...............................................................................2-8
2-2 I/O Terminal ......................................................................................................................................2-9
2-2-1 Output Signals from the Servo pack .................................................................................2-10
2-2-2 Encoder Connector (CN2) Terminal Layout......................................................................2-23
2-3 Typical Circuit Wiring Examples. .................................................................................................2-25
2-3-1 Position Control Mode (Pe Mode) (Line Driver). .............................................................2-25
2-3-2 Position Control Mode (Pe Mode) (Open Collector). .......................................................2-26
2-3-3 Position Control Mode (Pi Mode).......................................................................................2-27
2-3-4 Speed Control Mode (S Mode). ..........................................................................................2-28
2-3-5 Torque Control Mode (T Mode). .........................................................................................2-29

Chapter 3

Panel Operator / Digital Operator

3-1 Panel Operator on the Drives .........................................................................................................3-1

3-2 Signal Display ..................................................................................................................................3-8
3-2-1 Status Display ........................................................................................................................3-8
3-2-2 Diagnostic function ...............................................................................................................3-9

Chapter 4 Trial Operation

4-1 Trial Operation for Servomotor without Load...............................................................................4-2
4-2 Trial Operation for Servomotor without Load from Host Reference .........................................4-5
iii

4-3 Trial Operation with the Servomotor Connected to the Machine ...............................................4-9

Chapter 5 Control Functions

5-1 Control Mode Selection. .................................................................................................................5-1
5-2 Torque Mode ....................................................................................................................................5-2
5-2-1 Analog Torque command Ratio ...........................................................................................5-3
5-2-2 Adjusting the Analog Torque Command Offset .................................................................5-4
5-2-3 Torque Command Linear Acceleration and Deceleration ................................................5-5
5-2-4 Definition of Torque Direction ..............................................................................................5-6
5-2-5 Internal Torque Limit .............................................................................................................5-7
5-2-6 Limiting Servomotor Speed during Torque Control ..........................................................5-7
5-2-7 Additional Torque Control Functions..................................................................................5-8
5-3 Speed Mode......................................................................................................................................5-9
5-3-1 Selection for Speed Command .........................................................................................5-10
5-3-2 Analog Speed Command Ratio ..........................................................................................5-11
5-3-3 Adjusting the Analog Reference Offset.............................................................................5-11
5-3-4 Analog Reference for Speed Command Limit ..................................................................5-12
5-3-5 Encoder Signal Output........................................................................................................5-12
5-3-6 Smoothing the Speed Command.......................................................................................5-14
5-3-7 Setting Rotation Direction ..................................................................................................5-17
5-3-8 Speed Loop Gain .................................................................................................................5-18
5-3-9 Notch Filter...........................................................................................................................5-19
5-3-10 Torque Limit of Speed Control Mode.................................................................................5-21
5-3-11 Gain Switched......................................................................................................................5-22
5-3-12 Other Functions...................................................................................................................5-29
5-4 Position Mode ................................................................................................................................5-31
5-4-1 External Pulse Command ...................................................................................................5-32
5-4-2 Internal Position Command................................................................................................5-34
5-4-3 Electronic Gear ....................................................................................................................5-37
5-4-4 Smoothing Acceleration ....................................................................................................5-41
5-4-5 Definition of Direction .........................................................................................................5-44
5-4-6 Gain Adjustment ..................................................................................................................5-44
5-4-7 Clear the Pulse Offset .........................................................................................................5-45
5-4-8 Original Home ......................................................................................................................5-46
5-4-9 Other Position Function......................................................................................................5-55
5-5 Gain Adjustment ............................................................................................................................5-56
5-5-1

Automatic Adjusting ...........................................................................................................5-59

5-5-2 Manual Adjusting.................................................................................................................5-62

5-5-3 Improving Resonance .........................................................................................................5-63
5-6 Other Functions.............................................................................................................................5-64
5-6-1 Programmable I/O Functions .............................................................................................5-64
5-6-2 Switch for the Control Mode...............................................................................................5-67
5-6-3 Auxiliary Functions .............................................................................................................5-67
5-6-4 Brake Mode ..........................................................................................................................5-68
iv

5-6-5 Timing Diagram of Mechanical Brake ...............................................................................5-68

5-6-6 CW/CCW Drive Inhibit Function ........................................................................................5-70
5-6-7 Selecting for External Regeneration Resistor ..................................................................5-71
5-6-8 Fan Setting ...........................................................................................................................5-75
5-6-9 Analog Monitor ....................................................................................................................5-75
5-6-10 Factory setting Paramerter ..............................................................................................5-76

Chapter 6 Parameter Function

6-1 Explanation of Parameter Groups ................................................................................................6-1
6-2 Parameter Display Table ................................................................................................................6-2

Chapter 7 Communications Function

7-1 Communications Function (RS232 & RS485) ...............................................................................7-1
7-1-1 Communication wiring ...........................................................................................................7-1
7-1-2 RS232 Communication Protocol and Format .....................................................................7-6
7-1-3 Modbus communication protocol for RS-485 ....................................................................7-9
7-2 Communication Address table.....................................................................................................7-20

Chapter 8 Troubleshooting
8-1 Alarm Functions ..............................................................................................................................8-1
8-2 Troubleshooting of Alarm and Warning ........................................................................................8-3

Chapter 9 Specifications
9-1 Specifications and Dimension for Servo Drives ........................................................................9-1
9-2 Specifications and Dimension for Servomotors ..........................................................................9-6

Appendix A - Peripheral for Servo motors ...................................................................... App-1

Chapter 1 Checking and Installing

1-1 Checking Products
Our Servo Pack have already completely been functionally examined before leaving the factory. In order to protect the
products from the damage during transportation, please check the items below before sealing off the pack:
y

Check if the models of servo driver and motor are the same with the models of ordering.
(About the model explanation, please check the chapters below)

Check if there are damage or scrape out side of the servo driver and motor.
(If there is any damage during transportation, do not power ON)

Check if there are any bad assembly or slipped component in the Servo Drive and Motor

Check if the Motors rotor and shaft can be rotated smoothly by hand
(The Servo Motor with Mechanical-Brake can not be rotated directly)

There must be the QC-seal in each servo drive, if not, please do not proceed Power ON.

If there is any bug or irregular under the situation above, please contact TECOs Local sales representative or
distributor instantly.

1-1-1 Confirming with Servo Drives

JSD A 15
TECO AC Servo
Product No.

Input voltage phase:

Single / Three
33 Phase input

Drive Series:
Series A
Drive Model:
15 / 20 / 30 / 50 / 75 /
100 / 150 / 200 / 300

AC Input Voltage
A : AC 220V

P.S : Maximum output power

15 : 400 W 100 : 4.4 KW
20 : 750 W 150 : 5.5 KW
30 : 1 KW 220 : 7.5KW
50 : 2KW 300 : 15KW
75 : 3 KW

1-1

1-1-2 Confirming with Servo Motors

JSM

AP S

08

H K

TECO AC Servo
Product No.

B
M:Machinery BK
: No BK
B:BK

Motor Series:
Series A

Encode Spline Grease Seal

IP67 (except shaft and connector)

Motor Speed:
A: 1000 rpm
B: 2000 rpm
C: 3000 rpm
H: 1500 rpm
Motor Speed:
A: 1000 rpm
B: 2000 rpm
C: 3000 rpm
H: 1500 rpm

No

No

Yes

No

No

Yes

Yes

Yes

Encolder:
B : 2500 ppr
H : 8192 ppr
Motor ratio power
P5 : 50 W 20 : 2 KW
01 : 100 W 30 : 3 KW
03 : 300 W 44 : 4.4KW
04 : 400 W 55: 5.5 KW
05 : 550 W 75 : 7.5 KW
08 : 750 W 110 : 11 KW
10 : 1 KW 150 : 15 KW
15 : 1.5 KW

1-2

AC input voltage
A : AC 220V

1-2 Surface and Panel Board

JSDA-15A / 20A / 30A

JSDA-50A3 / 75A3 / 100A3

1-3

JSDA-150A3

JSDA-200A3 / 300A3

LED Display

Serial
Communication
Interface

Control Power
Input Terminal

Main-Power
Input Terminal

Motor Encoder Interface

*External
Regenerative
Resistor Terminal

I/O Interface

Motor Terminal
*Terminal P and PC
can not be closed
Ground
Terminal
FG

1-4

Key Board

1-3 A Brief Introduction of Operation for Drives

There are many kinds of control-mode. The detail modes display as fellow:
Name
Position Mode
(External Pulse

Mode

Position control for the servo motor is achieved via an external

Pe

Command)
Position Mode
(Internal Position

Explanation

pulse command. Position command is input from CN1.

Position control for the servo motor is achieved via by 16

Pi

Command)

commands stored within the servo controller. Execution of the

16 positions is via Digital Input signals.

Single

Speed control for the servo motor can be achieved via

Mode

parameters set within the controller or from an external analog

Speed Mode

-10 ~ +10 Vdc command. Control of the internal speed

parameters is via the Digital Inputs. A maximum of three steps
speed can be stored internally.
Torque control for the servo motor can be achieved via

Torque Mode

parameters set or from an external analog -10 ~ +10 Vdc

command.

Multiple Mode

Pe-S

Pe and S can be switched by digital-input-contact-point.

Pe-T
Pi-S
Pi-T
S-T

Pe and T can be switched by digital-input-contact-point.

Pi and S can be switched by digital-input-contact-point.
Pi and T can be switched by digital-input-contact-point.
S and T can be switched by digital-input-contact-point.

1-5

1-4 Conditions for Installation of Drives

1-4-1 Environmental Conditions
The product should be kept in the shipping carton before installation. In order to retain the warranty coverage, the
AC drive should be stored properly when it is not to be used for an extended period of time. Some storage suggestions
are:
y

Ambient Temperature: 0 ~ + 55 ; Ambient Humidity: Under 90% RH (Under the condition of no frost).

Stored Temperature: - 20 ~ + 85 ; Stored Humidity: Under 90%RH (Under the condition of no frost).

Vibrating: Under 0.5 G.

Do not mount the servo drive or motor in a location where temperatures and humidity will exceed specification.

To avoid the insolation.

To avoid the erosion of grease and salt.

To avoid the corrosive gases and liquids.

To avoid the invading of airborne dust or metallic particles.

When over 1 Drives are installed in control panel, enough space have to be kept to get enough air to prevent the
heat; the fan also must be installed, to keep the ambient temperature under 55 .

Please Install the drive in a vertical position, face to the front, in order to prevent the heat.

To avoid the metal parts or other unnecessary things falling into the drive when installing.

The drive must be stable by M5 screws.

When there were the vibrating items nearby, please using vibration-absorber or installing anti-vibration- rubber, if
the vibration can not be avoided.

When there is any big-size magnetic switch, welding machines or other source of interference. Please install the
filter. When the filter is installed, we must install the insulation transformer.

1-6

1-4-2 Direction and Distance

Fan

Fan
Over 10mm

Over 30mm

Over 25mm

Over 25mm

Air flow

Over 25mm

Air flow

1-7

Over 30mm

Over 10mm

1-5 Conditions for Installation of Servo Motors

1-5-1 Environmental Conditions
y

Ambient Temperature: 0 ~ + 40 ; Ambient humidity: Under 90% RH (No Frost).

Storage Temperature: - 20 ~ + 60 ; Storage temperature: Under 90%RH (No Frost).

Vibration: Under 2.5 G.

In a well-ventilated and low humidity and dust location.

Do not store in a place subjected to corrosive gases, liquids, or airborne dust or metallic particles.

Do not mount the servo motor in a location where temperatures and humidity will exceed specification.

Do not mount the motor in a location where it will be subjected to high levels of electromagnetic radiation.

1-5-2 Method of Installation

1. Horizontal Install: Please let the cable-cavity downside to prevent the water or oil or other liquid flow into the servo
motor.

Attention
BRAKE

Encoder

2. Vertical Install: If the motor shaft is side-up installed and mounted to a gear box, please pay attention to and avoid the
oil leakage from the gear box.

1-8

1-5-3 Notice for install motor

1. Please using oil-seal-motor to avoid the oil from reduction gear flowing into the motor through the motor shaft.
2. The cable need to be kept dry.
3. Please fixing the wiring cable certainly, to avoid the cable ablating or breaking.
4. The extending length of the shaft shall be enough, otherwise there will be the vibration from motor operating.

Wrong Example

Correct Example

5. Please do not beat the motor when installing or taking it apart. Otherwise the shaft and the encoder of backside will
be damaged.
Attention:

Brake

Encoder

1-9

Chapter 2 Wiring
2-1 Basic Wiring for Servo System
2-1-1 Wiring for Main Circuit and Peripheral Devices

2-1

2-1-2 Wiring for Servo Drives

y

The wire material must go by Wiring Specifications.

Wiring Length: Command Input Wire: Less than 3m.

Encoder Input Wire: Less than 20m.
The Wiring goes by the shortest length.

Please wire according to the standard wiring schema. Dont connect if no using.

Please use the NFB to meet IEC (or UL Certification) between power supplier and servo drive.

In the addition of supplying max. voltage, the capability of short circuit current must below 5000Arms, If there is
posibility t

Drive output terminals (U,V,W) must be connected to motor correctly. Otherwise the servo motor will abnormally
function.

Shielded cable must be connected to FG terminal.

Dont install the capacitor or Noise Filter at the output terminal of servo drive.

At the control-output-signal relay, the direction of surge absorb diode must be correctly connected, otherwise it
can not output signal, and cause the protect loop of emergency-stop abnormal.

Please do these below to avoid the wrong operation from noise:

Please install devices such as the insulated transformer and noise filter at the input power.
Keep more than 30 cm between Power wire (power cable or motor cableetc.) and signal cable, do not
install them in the same conduit.

Please set emergency-stop switch to prevent abnormal operation.

After wiring, check the connection-situation of each joint (ex: loose soldering, soldering point short, terminal order
incorrectetc.). Tighten the joints to confirm if surly connected to the servo drive, if the screw is tight. There can
not be the situations such as cable break, cable pulled and dragged, or be heavily pressed.
* Especially pay attention to the polarity between servo motor wiring and encoder.

There is no necessary to add extra regeneration resistance under general situation. If there is any need or
problem, please connect to distributor or manufacturer.

2-2

2-1-3 Specifications of Wiring

Connection Terminal
Connecti
on
Terminal

Terminal

Mark
(Sign)

Name of Connect
Terminal

15

R, S, T

Main Power Terminal

1.25
(16)

2.0
(14)

U, V, W

Motor Terminal

1.25
(16)

2.0
(14)

R,s

Power-Control Terminal

PPc

External regeneration
resistance terminal

1
FG
26,27,28
30,31
33,34
CN1
Joint
Control
Signal

CN2
Joint of
motor
encoder
CN3
CN4
Communi
cation
connector

Servo Drives and Wire Specifications mm (AWG)

29,32,44

20

30

50

75

100

150

200

300

5.5
(10)

8.0
(8)

22.0
(4)

5.5
(10)

8.0
(8)

14.0
(6)

22.0
(4)

3.5
(12)

5.5
(10)

8.0
(8)

22.0
(4)

3.5
(12)
3.5
(12)
1.25
(16)

1.25
(16)

2.0
(14)

Ground

Over 2.0(14)

Speed / Torque
Command Input
Analog Monitor Output
1&2
Power Output +15V &
-15V
Analog Ground
Terminal

0.2mm or 0.3mm -> Twisted-pair-cable connecting to the

Analog Grounding wire (including shield cable)

1~13,47

General Analog Input

18~25,43

General Analog Output

45,46,
48,49

24V Power &

I/O Ground

14~17,41

Position Command
Input

35~40

Encoder Signal Output

1,2

Output 5V

3,4

Output Grounding wire

of power supply

5~18

Encoder Signal Input

2,3

Data transfer & receive

Communication
grounding wire

1,4,6,8

Floating

0.2mm or 0.3mm -> Twisted-pair-cable connecting to the I/O

Grounding wire (including shield cable)

0.2mm or 0.3mm -> Twisted-pair-cable (including shield cable)

0.2mm or 0.3mm -> Twisted-pair-cable (including shield cable)

0.2mm or 0.3mm -> Twisted-pair-cable (including shield cable)

P.S.: 1. Please pay attention to the NFB and the capacity of noise filter when using multi ServoDrives.
2. CN1 ->50 Pins (3M Co.)
3. CN2 -> 20 Pins (3M Co.)
4. CN3/CN4-> 8 Pins Mini-Din type
2-3

2-1-4 Motor Terminal Layout

A Table of Motor-Terminal Wiring
(1) General Joint:
Terminal Symbol

Color

Signal

Red

White

Black

Green

FG

Fine red

DC +24V

Fine yellow

0V

Brake control wire

(2)Military Specifications Joint (No Brake):

Terminal

Color

Signal

Red

White

Black

Green

FG

(3)Military Specifications Joint(Brake):

Terminal

Color

Signal

Red

White

Black

Green

FG

Fine red

Fine yellow

F
E

DC +24V

A
G

BK control wire
0V

P.S.: The military joint with BK of servo motor has 9 Pins; and the encoder joint has also 9 Pins. Please
confirm before wiring.

2-4

Table of Motor-Encoder Wiring

(1)General Joint:
Terminal Symbol

Color

Signal

White

+5V

Black

0V

Green

Blue

/A

Red

Purple

/B

Yellow

Orange

/Z

Shield

FG

(2) Military Specifications Joint

Terminal Symbol

Color

Signal

White

+5V

Black

0V

Green

Blue

/A

Red

Purple

/B

Yellow

Orange

/Z

Shield

FG

2-5

2-1-5 Typical Wiring for Motor and Main Circuit

* The Wiring Example of Single Phase Main Power (Less than 1KW)

* The Wiring Example of 3 Phase Main Power (More than 1KW)

Power ON
Power OFF

MC
MC/a

r
s

NFB
Power Filter
3 Phase 220V

MC/R

MC/S

MC/T

TB1

Red

White

W
TB1

FG
P
PC

CN2

FG

2-6

Black
Green

R
External
Regeneration
BK Resistance

PG

2-1-6 TB Terminal
Terminal

Name

Detail

Sign

Control circuit power input

terminal

Connecting to external AC Power.

Single Phase 200~230VAC +10 ~ -15% 50/60Hz 5%

R
Main circuit power input
terminal

Connecting to external AC Power.

Single / 3 Phase 200~230VAC +10 ~ -15% 50/60Hz 5%

T
External regeneration
resistance terminal
Regeneration terminal
common point
Internal regeneration
resistance terminal
Motor-power output
terminal
Motor-case grounding
terminal

P1

Please refer to Cn012 to see resistance value, when using external

regeneration resistance. After installing regeneration resistance, set the
resistance power in Cn012.
*If no using external regeneration resistance, PC-P1 need be close, P
doesnt be connected.
*When using external regeneration, equip regeneration resistance
between PC-P, do not connect P1 terminal.

Motor terminal wire is red

Motor terminal wire is white

Motor terminal wire is black

FG

Motor terminal wire is green or yellow-green.

PC

TB Terminal Tightening Torque

JSDA-15A

Max. Tightening Torque (kgf-cm / in-lbs)

Control circuit
Main circuit
terminal(r , s)
terminal(R, S, T)
10 / 8.7

JSDA-20A

10 / 8.7

JSDA-30A

10 / 8.7

JSDA-50A3

16 / 13.9

JSDA-75A3

16 / 13.9

JSDA-100A3

16 / 13.9

Servo Pack Model

JSDA-150A3

18 / 15.6

30 / 26

JSDA-200A3

15 / 13

30 / 26

JSDA-300A3

15 / 13

30 / 26

2-7

2-1-7 Wiring for Mechanical Brake

Uninstall BRAKE:
z

JSMA-S/L/T series: Use Red wire and yellow wire connecting to DC +24V voltage(No polarity)

JSMA-M/H series: BK outputs from A & F of Motor Power Joint, servo motor can operate normally after
uninstalling.

JSMA-S/T/L

Yellow Wire
Yellow Wire

JSMA-M/H

A
F

Encoder

Brake

Encoder

Brake

2-1-8 MCCB/Fuse/Filter Recommended Specification

y

Please use the MCCB and Fuse to meet IEC (or UL Certification) between power supplier and servo drive.

Any noise issue which occurred during servo drive operation could be avoided by using filter.

Recommended Specification

Servo pack Model

MCCB

JSDA-15A

Fuse

Filter

Rating

Suggestion

Suggestion

10A

20A

Bussmann 20CT

Schaffner FN3258-7-45

JSDA-20A

15A

20A

Bussmann 20CT

Schaffner FN3258-7-45

JSDA-30A

15A

20A

Bussmann 20CT

Schaffner FN3258-16-45

JSDA-50A3

30A

40A

Bussmann 40FE

Schaffner FN3258-16-45

JSDA-75A3

30A

40A

Bussmann 40FE

Schaffner FN3258-16-45

JSDA-100A3

50A

63A

Bussmann 63FE

Schaffner FN3258-30-47

JSDA-150A3

50A

63A

Bussmann 63FE

Schaffner FN3258-42-47

JSDA-200A3

75A

100A

JSDA-300A3

125A

100A

Ferraz Shawmut
A50QS100-4
Ferraz Shawmut
A50QS100-4

2-8

Schaffner FN3258-42-47
Schaffner FN3258-75-47

2-2 I/O Terminal

There are 4 group terminal, which control signal terminal(CN1), encoder terminal(CN2) and communication
connector(CN3/CN4). The diagram below displays all positions for the terminal.

CN3, CN4 (Female)

Communication Connector
6

CN1 connector (Male)

2

24
CN2 connector (Male)
2

10

12

19

2-9

11

20

25

27

49

26

50

2-2-1 Output Signals from the Servo pack

(1) Diagram of CN1 Terminal:

P.S.:
1. If there is unused terminal, please do not connect it or let it be the relay terminal.
2. The Shielded Wire of I/O cable should connect to the ground.

2-10

(2) CN1 Signal Name and Explanation:

(a) General I/O Signal:
Explanation of General I/O Signal Function

Signal
Position Pulse
Command Input
Position Symbol
Command Input
Open Collector
Position Command
Power Input.
Speed / Torque
Analog Command
Input
Torque Control Speed
Limit Command /
CCW Torque
Command Limit
CW Torque
Command Limit
Analog Monitor
Output 1
Analog Monitor
Output 2
Home Signal Output

Function
Symbol

Pin No.

Pulse

14

/Pulse

15

Sign

16

/Sign

17

OPC

41

Wired
Mode

IO3

IO3

Function
Symbol

Pin No.

PA

35

/PA

36

PB

37

/PB

38

PZ

39

/PZ

40

AG

29,32,44

+15V

33

-15V

34

DICOM

47

+24Vdc Output

IP24

45

+24Vdc Com
Terminal

IG24

46,48,49

Shielded Wire
Connect Point

FG

50

Signal
Encoder Output
A-Phase
Encoder Output / A
Phase
Encoder Output
B-Phase
Encoder Output
/B-Phase
Encoder Output
Z-Phase
/Z-Phase

SIN

Analog Signal
Ground Terminal
+15Vdc Output
Terminal

26

IO5
PIC

27

-15Vdc Output
Terminal

NIC

28

DigitaI input Com

Terminal

MON1

30
IO6

MON2

31

ZO

43

IO2

2-11

Wired
Mode

IO4

Explanation of General I/O Signal Function

Signal Name
Position Pulse
Command Input
Position Sign
Command Input
Open Collect
Position Command
PW Input
Speed Analog
command Input

Function
Mode
Symbol
Pulse
/Pulse
Sign

OPC

SIN

PIC
CCW Torque Limit
Command

NIC

Analog Monitor
Output 1

MON1

Analog Monitor
Output 2

MON2

The Driver can receive 3 kinds of Command below:

(Pulse)+ (Sign)
(CCW)/ (CW)Pulse

Pe

When open collect input in position command, OPC and IP24

can be close, and using internal 24V power and resistor.

/PB

ZO

ALL Z Phase Open Collector output connect point.

Analog Signal
Ground Terminal

AG

ALL

DI PW Conmen

5-4-1

5-3-1
In Speed Mode, when external speed command is operated at
5-3-2
S SPD1=0, SPD2=0, input the voltage range: -10V~+10V, Sn216
5-3-3
can be set input voltage: 10Vs Motor output speed.
5-3-4
In Torque Mode, input the voltage range -10~+10V, Tn103 can 5-2-1
T
be set input voltage 10Vs motor output torque.
5-2-2
In Torque Mode, when external speed limit is operated at input
T connect point SPD1=0 & SDP2=0(P.S), input voltage range: 5-2-6
0~+10V, 10Vs speed limit stands for motors ratio speed.
In Speed Mode, when external torque limit is be used at input
connect point TLMT=1(P.S.) , input voltage range: 0~+10V, to
S
5-3-10
input 10V will limit the motor CCW torque having 300% of ratio
torque.
In Speed Mode, when external torque limit is be used at input
connect point TLMT=1(P.S.), input voltage range: -10~0V, to
5-3-10
S
input -10V will limit the motor CW torque have 300% of ratio
torque.
Operating the motor to control the current speed to transform
the voltage output in accordance with the rate (10V/1.5 times
5-6-9
ALL
ratio speed) CCW stands for positive voltage, CW negative
voltage.
Operating the motor to control the current torque to transform
the voltage output in accordance with the rate (10V/3.5 times
ALL
5-6-9
ratio torque) CCW torque stands for positive voltage, CW
negative voltage.

Encoder Output A
Phase
Encoder Output / A
Phase
Encoder Output B
Phase
Encoder Output / B
Phase
Encoder Output Z
Phase
Encoder Output / Z
Phase
Home Signal
Output

+15V PW Output
Terminal
-15V PW Output
Terminal

Chapter

AB Phase pulse

/Sign

Torque Analog
Command Input
Torque Control
Speed Limit
Command

CW Torque Limit
Command

Pe

I/O Operation and Function

PA
/PA
PB

PZ

Outputting the Motor Encoder Signal through pulse per rotation

handle. The pulse quantity of every rotating can be set in
Cn005.
5-3-5
ALL
When 1 is set in Cn004, it is CCW rotation from the motor load
terminal direction, and A Phase gets 90 degree ahead B Phase.
Signal Output is Line Driver.

/PZ

+15V
-15V
DICOM

Analog signal grounding: CN1 - > Pin 2627283031

3334.

ALL To provide 15V output power (Max. 10mA), which can be used
in servo drive external voltage command. Suggestion: Using
ALL the variable resistance which is more than 3k.

ALL Digital input power supplement common terminal.

2-12

Signal Name

Function
Mode
Symbol

I/O Operation and Function

Chapter

Terminal
+24V PW Output
+24V PW Ground
Terminal
Shielded Wire
Connect Point

IP24

ALL +24V power output terminal(Max. 0.2A).

IG24

ALL +24V power grounding terminal

ALL Connect to Shield wire of signal cable.

FG

P.S.: 1 stands for close loop with IG24; 0 stands for open loop with IG24.
PW is abbreviation of Power

2-13

(b) Digital I/O Signal:

For many kinds of application, the digital input/output terminal layout of all operation mode are accordingly
different. In order to provide more functions, our drives can provide multi terminal layout settings. Users can set these
functions for application.
Digital input terminal layout provides 13 (Pin1~13) programmable terminal; digital output terminal provides 4
(Pin18~21) programmable terminals. The diagram below shows the default digital input/output terminal placement
and functions. Please refer to 5-6-1 to check related parameters setting.

Default Digital Input Terminal placement Functions and Wired Mode

Signal

Function
Sign

Pin
No.

Wired
Mode

Signal

Function
Sign

Pin
No.

Servo ON

DI-1

SON

Servo Lock

DI-8

LOK

Alarm reset

DI-2

ALRS

Emergency
Stop

DI-9

EMC

PI/P Switch

DI-3

PCNT

DI-10

SPD1

10

CCW
Operation Limit

DI-4

CCWL

DI-11

SPD2

11

CW
Operation Limit

DI-5

CWL

DI-12

MDC

12

External Torque
Limit

DI-6

TLMT

DI-13

SPDINV

13

Pulse error
amount delete

DI-7

CLR

IO1

Internal speed
command /
Limit select 1
Internal speed
command /
Limit select 2
Control Mode
Switch
Reverse
Direction
Speed
Command

Wired
Mode

IO1

Default Digital Input Terminal Layout Functions and Wired Mode

Signal

Function
Sign

Pin
No.

Wired
Mode

Signal

Function
Sign

Pin
No.

Servo ready

DO-1

RDY

18

Torque limit/
Alarm code A0

DO-5

LM/A0

22

Alarm

DO-2

ALM

19

P action /
Alarm code A1

DO-6

PC/A1

23

IO2

Wired
Mode

IO2

Zero speed

DO-3

ZS

20

Operation limit/
Alarm code A2

DO-7

ST/A2

24

Fix position

DO-4

INP

21

Base Block/
Alarm code A3

DO-8

BB/A3

25

2-14

Digital Input Function

(Except CCWL and CWL are high electric potential, other terminal layout are low electric potential. Please refer
to 5-6-1 to see related parameters)
Signal Name

Function
Sign

Servo On

SON

Abnormal Reset

ALRS

PI/P switch

PCNT

CCW
Operation limit

CCWL

ALL

Connect to CCW over travel detector: CCWL and IG24 close loop;
open loop with IG24 -> CCW over travel operates.

CW
Operation limit

CWL

ALL

Connect to CW over travel detector: CWL and IG24 close loop;

open loop with IG24 -> CW over travel operates.

External torque
limit

TLMT

Pulse error
amount delete

CLR

Servo lock

LOK

Emergency stop

EMC

ALL

Internal speed
command / limit
select 1
Internal speed
command / limit
select 2

SPD1
SPD2

Mode

I/O Function

Chapter

SON and IG24 close loop: Servo ON ; SON and IG24 open loop:
Servo OFF. Attention: Before power on, the input connect point
SON (servo on) can not be operated to avoid danger.
ALRS and IG24 close loop: Relieving the stop-situation from of
abnormality. But the abnormality of encoder or memory will
ALL
cause the same alarm again. Please reset power after the
abnormality is eliminated.
PCNT and IG24 close loop will cause the speed loop control
Pi/Pe/S transforming to ratio control from ratio integration control.
ALL

5-6-3
5-6-4
8-1

5-3-11
5-4-8
5-6-3
5-6-4
5-4-8
5-6-3
5-6-4

TLMT and IG24 close loop will cause the motor-output-torque-limit

Pi/Pe/S to stay in the command-voltage range of
5-3-10
torque-limit-terminal-layout (PICNIC).
When CLR and IG24 close loop, delete the pulse amount in the
Pi/Pe Position Error Counter.
5-4-7

S/T

When LOK and IG24 close loop will transform speed control mode
5-3-12
into position control mode in order to lock the motor at the last
position.
When EMC and IG24 close loop: Emergency stop -> Servo Off and
exit the rotating statue, and Cn008 will decide if the dynamic Brake 5-6-4
operates.

SPD2

SPD1

Speed
Command
(Speed Mode)

Speed Limit
Command
(Torque Mode)

External
command(SIN)

External limit(PIC)

Sn201

Tn105

Sn202

Tn106

Sn203

Tn107

Internal speed setting and limit:

1: Close loop with IG24
0: Open loop with IG24

2-15

5-2-6
5-3-1

Digital Input Function Explanation

(Except CCWL and CWL are the high electric potential, other terminal layout are the low electric potential,
please refer to 5-6-1 to check related parameters setting)
Signal Name
Control Mode
Switch
Position
Command Limit
Speed Command
Counter Wise
Gain Select

Electric Gear ratio

Numerator 1~2

Internal Position
Command
Trigger
Internal Position
Command Hold

Function
Symbol
MDC
INH
SPDINV
G-SEL

GN1
GN2

PTRG
PHOLD

Home

SHOME

External Origin

ORG

Mode

I/O Function

When MDC and IG24 close loop, current control mode will
Pe/S/T transform into default control mode, please refer to Cn001.
When INH and IG24 close loop, position command input does
not operate (do not accept external pulse command).
When SPDINV and IG24 close loop in speed mode, setting
S
rotating speed will become counter-wise rotating speed.
When G-SEL and IG24 close loop, first stage control gain
Pi/Pe/S switch to the second control gain.
Electric gear ratio: select explanation:
Pe

Pi/Pe

GN2
0
0
1
1

GN1
0
1
0
1

Electric Gear ratio Numerator

Pn302
Pn303
Pn304
Pn305

1: Close loop with IG24

0: Open loop withIG24
When PTRG and IG24 close loop (positively-triggered), the
motor will select related position command to operate in
Pi
accordance with the terminal layout POS1~POS4.
When PHOLD and IG24 close loop(positively-triggered), the
Pi
motor will stay holding.
When SHOME and IG24 close loop(positively-triggered),
Pi/Pe
HOME function operates
When ORG and IG24 close loop(positively-triggered), server
Pi
will use this as external reference point for home position
returning.

2-16

Chapter

5-1
5-6-2
5-4-1
5-3-7
5-3-11

5-4-3

5-4-8
5-4-8
5-4-8
5-4-8

Digital Input Function Explanation

(Except CCWL and CWL are the high electric potential, other terminal layout are the low electric potential,
please refer to 5-6-1 to check related parameters setting)
Signal Name

Function
Symbol

Mode

I/O Function

Chapter

Internal position command select :

Internal Position
Command select
1~4

POS1
POS2
POS3
POS4

Pi

POS1

POS2

POS3

POS4

0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1

0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1

0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1

0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1

Internal Position
Command select
Pn317, Pn318
Pn320, Pn321
Pn323, Pn324
Pn326, Pn327
Pn329, Pn330
Pn332, Pn333
Pn335, Pn336
Pn338, Pn339
Pn341, Pn342
Pn344, Pn345
Pn347, Pn348
Pn350, Pn351
Pn353, Pn354
Pn356, Pn357
Pn359, Pn360
Pn362, Pn363

5-4-2

Internal position command select explanation:

1: close loop with IG24
0: open loop with IG24

Torque Command
Counter Clock TRQINV
Wise

When TRQINV and IG24 close loop in torque mode, setting

torque command output wise becomes counter wise output.

5-2-4

External torque command direction select :

External torque
command
direction select

RS1
RS2

RS2

RS1

No torque command input

According to torque command

Opposite direction for currently torque
command
No torque command input

Statement

1 means short with IG24.

0 means open with IG24.

2-17

5-2-4

Digital Output Function Explanation

(The terminal layout here from this explanation are all the low electric potential, please refer to 5-6-1 to check
parameter settings)
Signal Name

Function
Symbol

Servo Ready

RDY

Alarm

ALM

Zero Speed

ZS

BK Signal

BI

In Speed

INS

In Position

INP

Home
Torque Reach
signal

HOME

Limiting Torque/
Alarm No. 0
P in Action /
Alarm No.1

INT

LM/A0

PC/A1

Mode

I/O Function

Main power and control power input are normal. Under the
situation of no alarm, terminal layouts RDY and IG24 close
loop.
If normally operates, the terminal layouts ALM and IG24 open
ALL loop. When alarm occurs, protection-function operates, the
terminal and IG24 close loop.
When the motor speed is less than the speed from Sn215, the
S
terminal layout ZS and IG24 close loop.
When Cn008 is set 1 or 3 and the servo on, the terminal
layout BI and IG24 close loop; when servo off , terminal layout
ALL and IG24 open loop. (When this terminal layout is generally
applied, it is the Brake relay, which is connected to control
motor).
When the motor speed has achieved the setting speed from
S
Cn007, INS and IG24 close loop.
When the amount of position error counter is less than the
Pi/Pe
amount range which is set in Pn307, INP and IG24 close loop.
Pi/Pe When HOME is accomplished, HOME and IG24 close.
When the output torque reached the setting value of Tn108, INT
ALL
and IG24 close.
When motor output torque is limited by internal torque limit
amount (Cn010&Cn011) or external torque limit command
ALL (PIC&NIC). LM/A0 and IG24 close loop.
When alarm occurs, this terminal layout is alarm code output
A0.
When speed loop is ratio(P)-control, PC/A1 and IG24 close
loop.
Pe/Pi/S
When alarm occurs, this terminal layout is alarm code output
A1.
ALL

Server in Limiting/
Alarm No.2

ST/A2

ALL

Base Block/
Alarm No.3

BB/A3

ALL

When CCW or CW operation-limit occurs, ST/A2 and IG24 close loop.

When alarm occurs, this terminal layout is alarm code output A2

When servo motor has not be operated, BB/A3 and IG24 close
loop.
When alarm occurs, this terminal layout is alarm code output A3

2-18

Chapter

5-3-12
5-6-4
5-6-5
5-3-12
5-4-9
5-4-8

8-1

8-1
8-1
8-1

(3) CN1 Interface Circuit and Wire Mode:

The diagram below introduces all interface circuit of CN1 and wire-method of host controller.
(a) Digital input interface circuit (IO1):
Digital input interface circuit can be operated by relay or collector transistor circuit. The relay should be the low
electric current, in order to avoid the faulty contacting. External voltage: 24V.
Internal 24V Power

External 24V Power

Servo Driver

DC24V
IP24

CN1-45

CN1-47

i=4.3mA

5.6K

DICOM
SON

CN1-49

IG24

(b) Digital Output Interface Circuit(IO2):

When using external power, please attention to the power polarity. Adverse polarity will case circuit damage.
Digital output is Open Collector. The maximum of external voltage is 24V; and the maximum electric current is
10mA.
Internal 24V Power

External 24V Power

2-19

(c) Pulse Command Input Interface Circuit(IO3):

Suggesting to use the input method of Line Driver to send the pulse command. The maximum input command
frequency is 500kpps. Using the input method of Open Collector will cause the decrease of input command
frequency, the maximum input command frequency is 200kpps. The servo provides only 24V power, and other
power should be prepared. Adverse polarity of power will cause the servo damage. The maximum of External
power (Vcc) is 24V limited. Input current is about 8~15mA. Please refer to the examples below to select
resistance. Please refer to 5-4-1 to check pulse input command timing.

Line Driver pulse command input

The max. frequency of line driver type pulse command

is 500kpps

Open Collector pulse command input

Maximum input command frequency of open collector is

200kpps

Open Collector (Internal 24V)

Open Collector Selection of input Resistance

Servo Driver
DC24V
IP24

CN1-45
CN1-41

OPC

2K
330

Pulse
Sign

External Power

External Power

External Power

Vcc=24V

Vcc=12V

Vcc=5V

R=2K

R=750

R=100

1K
/Pulse
/Sign
CN1-49

IG24

The maximum input command frequency of open

collector is 200kpps

2-20

(d) Encoder Output Interface Circuit (IO4):

Encoder output interface circuit is the output method of Line Driver, please let end terminal
resistance(R=200~330) connect to Line Receiver input terminal.
Encoder Output Interface Circuit (Line Driver)

(e) Analog Input Interface Circuit(IO5):

There is sometimes ripple inside the servo internal power. Adverse external power polarity will cause severe
damage. Maximum external power voltage (Vc) should be less than12V; terminal input voltage should not more
than10V. Over voltage will cause damage. When using internal power of server, user need to choose the
resistance(suggestion: more than 3K), which maximum current is less than 10mA.
SIN Input impedance: 15K
PIC Input impedance: 40K
NIC Input impedance: 20K

Analog Input Interface Circuit

2-21

(f) Analog Output Interface Circuit(IO6):

The maximum current of analog output is 5mA, so user need to choose the device, which Impedance is larger.

Analog Input Interface Circuit

Servo Driver

TG
V
AG

2-22

2-2-2 Encoder Connector (CN2) Terminal Layout

(1) Diagram of CN2 Terminal:
(a) Diagram of Fewer Wiring Type Encoder:

(b) Diagram of non-Fewer Wiring Type Encoder:

P.S.: Do not wire to the terminal, which is un-operated.

2-23

(2) Name and Explanation of I/O Signal:

Encoder Output
No. and Color
Pin
No.

Signal Name

Code

General
Joint
9 wires
(fewer
wiring)

Plug-in
Joint

15 wires
Output
(non-fewer
No.
wiring)

1
2

Power output
+ Terminal

+5V

white

Red

3
4

Power output
- Terminal

0V

Black

Black

Green

/A

Blue

Red

Green
Green
White
Gray

/B

Pink

Gray white

Yellow

/Z

Orange

Yellow
Yellow
white
Brown
Brown
white
Blue

/V

Blue white

Orange
Orange
white

5
6
7
8
9
10
11
12
13
14
15
16

A Phase encoder
input A
B Phase encoder
input
Z Phase encoder
input
U Phase encoder
input
V Phase encoder
input
W Phase encoder
input

17
18
19

No operated

20

Shielded wire
terminal layout

U
/U

/W

Terminal Layout Function

5V Power for encoder (provided from driver).

When the cable is more than 20m, user should
separately use 2 cables to avoid decreasing
voltage of encoder. When the cable is more
than 30m, please contact to the distributorship.

Encoder A Phase: From motor terminal to the

driver.
Encoder B Phase: From motor terminal to the
driver.
Encoder Z Phase: From motor terminal to the
driver.
When using fewer-wiring-type motor, do
not wire.
When using fewer-wiring-type motor, do
not wire.
When using fewer-wiring-type motor, do
not wire.

Do not wire.

FG

Shielded net wire

2-24

Shielded wire, which is connected to the signal

wire.

2-3 Typical Circuit Wiring Examples

2-3-1 Position Control Mode (Pe Mode) (Line Driver)

Pe mode =External pulse positioning command

2-25

2-3-2 Position Control Mode (Pe Mode) (Open Collector)

Pe mode =External pulse positioning command

2-26

2-3-3 Position Control Mode (Pe Mode) (Pi Mode)

NFB

R
Supply
Filter

S
T

S
T

SERVO

FG

Digital input common

IP24
DICOM

PC
Regeneration resistor

P
PC
P1

DC 24V

Internal +24V DC

RS232

C
N
4

r
s

45

47

SERVO
MOTOR

V
Servo ON ( SON)
CCW Limit ( CCWL)
CW Limit ( CWL)
Emergency stop ( EMC)
HOME ( SHOME)
External Torque Limit ( TLMT)
Position Trigger ( PTRG)
Alarm Clear ( ALRS)
Position Hold ( PHOLD)
Position Select 1 ( POS1)
Position Select 2 ( POS2)

+24V ground

CCW Torque Limit

Analog Grounding
CW Torque Limit

Shield ground

DI-1

DI-4

DI-5

DI-9

DI-3

DI-6

DI-12

12

DI-2

DI-8

DI-10

10

DI-11

IG24

PIC
AG
NIC

FG

11

R1

FG

R1

Encoder
C
N
2

R1

R1

35

PA

R1

36

/PA

R1

37

PB

R1

38

/PB

R1

39

PZ

40

/PZ

R1

Encoder Output A Phase

Encoder Output /A Phase
Encoder Output B Phase
Encoder Output /B Phase
Encoder Output Z Phase
Encoder Output /Z Phase

R1

43
48

R1

DC24V

48

27
29
28

20K
R2

Z0

R4

IG24

+Vc Origin Output

*Max Vc:24V
Vc=24V, R4=4.7K
Vc=12V, R4=2.4K
Vc=5V, R4=1.0K

45
18

DO-1

LOAD

Servo Ready (RDY)

19

DO-2

LOAD

Alam(ALM)

20

DO-3

LOAD

HOME (HOME)

21

DO-4

LOAD

Positioning Completed(INP)

22

DO-5

LOAD

Limiting Torque/Alarm Code 0

23

DO-6

LOAD

P in Action/Alarm Code 1

24

DO-7

LOAD

Servo in limit/ Alarm Code 2

25
49

DO-8

LOAD

Base Block /Alarm Code 3

Max Voltage: 24V

Max Output Current :10mA

IG24

20K
R2

50

Pi mode =Internal position command

2-27

30

MON1

32

AG

31

MON2

33

+15V

34

- 15V

Analog Monitor Output 1

Analog Grounding

Max Output Current 5mA

Analog Monitor Output 2

+15V PW output (AG)

Max Output Current 10mA
-15V PW output (AG)

2-3-4 Speed Control Mode (S Mode)

NFB

R
Supply
Filter

S
T

S
T

SERVO

FG
45

Internal +24V DC
Digital input common

Servo ON ( SON)

CCW Limit ( CCWL)

CW Limit ( CWL)
Emergency stop ( EMC)

PI/P Switch ( PCNT)

Torque Limit ( TLMT)
Model Control ( MDC)
Alarm Clear ( ALRS)
Look ( LOK)
Speed 1 (SP1)

DICOM

DI-1
DI-4

1
4

DI-5

DI-9

DI-3

DI-6

DI-12

12

DI-2

DI-8

DI-10

10

Speed 2 (SP2)
Reverse Control ( SPDINV)

DI-13

13

IG24

48

Analog Ground
CW Torque Limit

Analog Speed Input (10V)

Analog Ground

Shield ground

SERVO
MOTOR

11

CCW Torque Limit

47

DI-11

+24V ground

PC
Regeneration resistor

P
PC
P1

DC 24V

IP24

RS232

C
N
4

r
s

PIC
AG
NIC

SIN
AG

FG

FG

R1

Encoder

C
N
2

R1

R1

35

PA

R1

36

/PA

R1

37

PB

R1

38

/PB

R1

39

PZ

40

/PZ

R1

Encoder Output A Phase

Encoder Output /A Phase
Encoder Output B Phase
Encoder Output /B Phase
Encoder Output Z Phase
Encoder Output /Z Phase

R1

43
48

R1

DC24V

R1

20K

27
29
28

26
29

R1

R2

Z0

R4

IG24

+Vc

External supply
*Max Vc=24V
Vc=24V, R4=4.7K
Vc=12V, R4=2.4K
Vc=5V, R4=1.0K

45
18

DO-1

LOAD

Servo Ready (RDY)

19

DO-2

LOAD

Alam(ALM)

20

DO-3

LOAD

Zero Speed (ZS)

21

DO-4

LOAD

In Speed (INS)

22

DO-5

LOAD

Limiting Torque/Alarm Code 0

23

DO-6

LOAD

P in Action/Alarm Code 1

24

DO-7

LOAD

Servo in limit/ Alarm Code 2

25
49

DO-8

LOAD

Base Block /Alarm Code 3

Max Voltage: 24V

Max Output Current :10mA

IG24

20K
R2

20K

30

MON1

32

AG

31

MON2

R2

50

2-28

33

+15V

34

- 15V

Analog Monitor Output 1

Analog Grounding

Max Output Voltage 5mA

Analog Monitor Output 2

+15V PW output (AG)

Max Output Current 10mA

-15V PW output (AG)

2-3-5 Torque Control Mode (T Mode)

NFB

R
Supply
Filter

S
T

SERVO

S
T

FG
45

P
PC
P1

47

DC24V

Internal+24 V DC

IP 24

Digital input common DICOM

RS232

C
N
4

r
s

PC
Regeneration resistor

SERVO
MOTOR

V
Servo ON ( SON)
CCW Limit( CCWL)
CW Limit ( CWL)
Emergency stop( EMC)
Model Control( MDC)
Alarm Clear( ALRS)
Torque Inverse(TRQINV)
Speed1 (SPD1)
Speed2 (SPD2)
Torque CW Selecting (RS1)
Torque CCW Selecting (RS2)
+24 V ground

Torque Control
Speed Limit (0~10V)
Analog Ground

Torque Input(10V)
Analog Ground

Shield ground

DI-1

DI-4

DI-5

DI-9

DI-12

12

DI-2

DI-8

DI-10

10

DI-11

11

R1

35

PA

R1

36

/ PA

R1

37

PB

R1

38

/ PB

R1

39

PZ

R1

40

/ PZ

DI-7

R1

IG24

48

FG

43
48

DC24V

20K

27
29

26
29

Encoder
C
N
2

R1

DI-6

SIN
AG

FG

R1

R1

PIC
AG

R1

R2

Z0

Encoder Output A Phase

Encoder Output /A Phase
Encoder Output B Phase
Encoder Output /B Phase
Encoder Output Z Phase
Encoder Output /Z Phase

R4

IG24

45
18

DO-1

19

DO-2

20

DO-3

21

DO-4

22

DO-5

23

DO-6

24

DO-7

25
49

DO-8

+ Vc External supply
*Max Vc=24V
Vc=24V , R4=4.7K
Vc=12V , R4=2.4K
Vc=5V , R4=1.0K

LOAD

Servo Ready ( RDY)

LOAD

Alam( ALM)

LOAD

Zero Speed (ZS)

LOAD

In Speed ( INS)

LOAD

Limiting Torque /Alarm Code 0

LOAD

P in Action /Alarm Code 1

LOAD

Servo in limit /Alarm Code 2

LOAD

Base Block /Alarm Code 3

Max Voltage: 24V

Max Output Current:10mA

IG24

20K

30

MON1

32

AG

31

MON 2

R2

50

2-29

33

+15V

34

- 15V

Analog Monitor Output 1

Analog Grounding

Max Output Current 5mA

Analog Monitor Output 2

+15V PW output (AG)

Max Output Current 10mA
-15V PW output (AG)

Chapter 3 Panel Operator / Digital Operator

3-1 Panel Operator on the Drives
The operator keypad & display contains a 5 digit 7 segment display, 4 control keys
and two status LED displays.
Power status LED (Green) is lit when the power is applied to the unit.
Charge LED (Red) Indicate the capacitor s charge status of main circuit. power on to light up Charge LED
and gradual dark when internal power capacitors are discharged complete.
Do NOT wire or assemble to the servo drive before Charge LED is off.

Key

Name
MODE/SET

INCREMENT
DECREMENT
DATA SETTING
&
DATA ENTER

Function Keys Description

1. To select a basic mode, such as the status display mode, utility
function mode, parameter setting mode, or monitor mode.
2. Returning back to parameter selection from data-setting screen.
1. Parameter Selection.
2. To increase the set value.
3. Press
and
at the same time to clear ALARM.
1. To confirm data and parameter item.
2. To shift to the next digit on the left.
3. To enter the data setting (press 2 sec.)

3-1

After power on, MODE button can be used to select 9 groups of parameter.
By pressing the Mode key repeatedly once at a time you can scroll trough the displays below.
Step

Key

Power on

Description

LED Display after Operation

Drive status parameters.

Diagnostic parameters.

Alarm parameters.

System Control parameters.

Torque Control parameters.

Speed Control parameters.

Position Control parameters.

Quick set up parameters.

Multi function I/O ( programmable Inputs/Outputs) Parameters.

10

Return to Drive status parameters.

3-2

Once the first parameter in a parameter group is displayed use Increment or Decrement keys to
select the required parameter then use Enter key in order to view and alter the parameter setting,
once this is done then press Enter key again to save the change.
Notes: On each parameter display the first digit will be flashing, the enter key can be used
to move between digits.
Example procedures are shown below: Ex: Setting Speed Parameter Sn203 to 100rpm.
Step

Key

Power On

Description

LED Display after Operation

Display status of servo drive

Press MODE-Key 6 times to select Sn 201

Press INCRMENT- Key twice Sn203 is displayed.

To view the Sn203 preset value by press ENTER-Key for 2

seconds

Shift to the second digit by press ENTER- Key once

Shift to next Digit by press ENTER-Key once again

Change the digit preset value by press the DECREMET-Key

twice

To save the altered preset value, Press the ENTER- Key for 2
seconds until SETis displayed briefly and then display is
returned to parameter Sn203
Following example shows the sequence where a parameter preset value is displayed
When no change is made and it is skip back to the original parameter by pressing the Mode-Key.

Step

Key

Power ON

Description

LED Display after Operation

When power on drive status parameter will display

Pressing MODE-Key 6 times, Sn 201 will be displayed.

Pressing INCRMENT- Key twice Sn203 is displayed.

To view the Sn203 preset press ENTER-Key for 2 seconds.

No change is made and LED display return to last select parameter

Sn203, press MODE-Key once skip

3-3

Some of the data entry in this drive are in the format shown below, for these data the Most significant digit
will be shown by the Capital letter H as shown below.
Ex: Home search function in position mode Pn365 = 0212. Each digit of this preset for Pn365 parameter
defines a selection for a specific function.
Bit0 corresponds to a selection for parameter Pn 365.0 and bit1 setting for Pn 365.1 etc.
Parameter Pn 365 Format for the 5 digits data value is shown below:

Display of Positive and Negative values:

Description of Positive/Negative Display

Display of Positive Display of Negative

For negative numbers with 4 digits or less, the negative sign is

displayed In the most significant digit as shown.
Ex: Sn201 (Internal Speed Command 1).

3000

-3000

For negative numbers with 5 digits the negative sign is indicated by

displaying all the 5 decimal points on the display.
Ex: Pn317(Internal Position Command 1- Rotation number)

30000

-30000

Setting a negative value.

(1) If the negative value has 4 digits or less follow the steps in the example below:
Ex: Sn201(Internal speed command 1)= preset speed of 100 to 100 rpm.
Step

Key

Power ON

Description

LED Display after Operation

On power on Drive Status parameter is displayed.

Pressing MODE-Key 5 times, Sn 201 will be displayed.

To view the Sn201 preset press ENTER-Key for 2 seconds.

To move to the most significant digit press the ENTER-Key

4 times.

or

Use INCREMENT Or DECREMENT key until

the minus sign ( _ ) is displayed. You can toggle between and
+ by this key.

To save the altered preset value, Press the ENTER- Key for 2
seconds until SETis displayed briefly and then
display is returned to parameter Sn201.

3-4

If the negative value has 5 digits follow the steps in the example below:
Ex: Pn317 (internal position preset command 1) set to a negative value -10000 revolutions.
Step
1

Description

Control Keys LED Display after Operation

Power On

On power on Drive Status parameter is displayed.

Pressing MODE-Key 6 times, position parameter Pn 301 will

be displayed.

Use INCREMENT- Key to display Pn317.

To view the Pn317 preset press ENTER-Key for 2 seconds.

To move to the most significant digit press the ENTER-Key

4 times.

Press DECREMENT-Key once to set the most significant digit

To 1. And press the DECREMENT-Key once again.
All 5 decimal points will light up to indicate a negative number.

To save the altered preset value, Press the ENTER- Key for 2
seconds until SETis displayed briefly and then
display is returned to parameter Pn 317.

Alarm Reset from the Keypad.

All alarm displays can be cleared from the keypad without a need for an external Alarm clear (Reset) signal.

Ex. Under voltage Alarm AL-01.

Step

Control Key

Alarm

Description

LED Display after Opertion

Under voltage Alarm AL-01 is displayed.

To clear Alarm:Remove input contact SON (Servo On).
Then press INCREMENT-Key and DECREMENT-Key
at the same time.
The display will show RESET briefly and then returns back to
parameter display.

3-5

The LED display contains status code and the digit of LED, the LED shows different meaning in
Torque/Speed control mode and Position control mode, the statement is below.
(1) Speed and Torque control mode

The following table describes the digit and status code.

Digit
BASE BLOCK
Speed Reached
(INS)
Speed Command
Reached
Torque Command
Reached

Description
Digit Lighting

Digit Off

Servo OFF
Motor speed was greater than
Cn007(Speed reached preset)
Speed command was greater than
Cn007(Speed reached preset)
Torque command was greater than 0%
of rated torque.

Servo ON
Motor speed was less than
Cn007(Speed reached preset)
Speed command less than
Cn007(Speed reached preset)
Torque command was less than 0% of
rated torque.

Status Code

Description
BASE BLOCK
Servo OFF (Motor hasnt established the magnetic flux)
Servo drive running
Servo ON (Motor is establishing the magnetic flux)
CCW direction banned
Input contact(CCWL) operation.
CW direction banned
Input contact(CWL) operation.

3-6

(2) Position control mode

The following table describes the digit and status code.

Digit
BASE BLOCK
Position Complete
(INP)
Speed Reached
(INS)
External Pulse
Train Command
Pulse Error Clear
Mode

Description
Digit Lighting
Servo OFF
Position error was less than
Pn307(Position complete value)
Motor speed was greater than
Cn007(Speed reached preset)

Digit Off
Servo ON
Position error was greater than
Pn307(Position complete value)
Motor speed was less than Cn007
(Speed reached preset)

External Pulse Train Command

Internal Pulse Command

Input Contact CLR(Pulse error clear)

opration

Input Contact CLR(Pulse error clear)

Disable

Status Code

Description
BASE BLOCK
Servo OFF(Motor hasnt established the magnetic flux)
Servo drive running
Servo ON(Motor is establishing the magnetic flux)
CCW direction banned
Input contact(CCWL) operation.
CW direction banned
Input contact(CWL) operation.

3-7

3-2 Signal Display

3-2-1 Status Display
Following parameters can be used to display drive and motor Status.
Parameter
Signal

Displayed

Unit

Description

Un-01

Actual motor speed

rpm

Actual Motor Speed is displayed in rpm.

Un-02

Actual motor torque

It displays the torque as a percentage of the rated torue.

Ex: 20 are displayed. It means that the motor torque output is 20% of
rated torque.

Un-03

Regenerative load ratio

Value for the processable regenerative power as 100% .

Un-04

Accumulated load ratio

Value for the rated torque as 100%.

Un-05

Max load rate

Max value appeared on accumulated load rate

Un-06

Speed command

Un-07

Position error counter value

pulse

Un-08

Position feedback pulse counter

pulse The accumulated number of pulses from the motor encoder.

Un-09

External voltage command

External analog voltage command value in volts.

Un-10

Main circuit Vdc Bus Voltage

DC Bus voltage in Volts.

Un-11

External speed limit command

value

Un-12

External CCW Torque limit

command value

Ex: Display 100. Means current external CCW torque limit command is
set to 100 %.

Un-13

External CW Torque limit command

value

Ex: Display 100. Means current external CW toque limit command is set
to 100%.

Un-14

Motor feed back Rotation value

(absolute value)

rev After power on, it displays motor rotation number as an absolute value.

Un-15

Motor feed back Less then 1

After power on, it displays the pulse number for less than a revolution of
pulse
the motor as an absolute value.
rotation pulse value(absolute value)

Un-16

Pulse command rotation

value(absolute value)

Un-17

Pulse command Less then 1

After power on, it displays pulse command input for less than a rotation.
pulse
pulse value is an absolute value.
rotation pulse value(absolute value)

Un-18

Torque command

Un-19

Load inertia

Un-20

Digital Output status(Do)

The status of digital output represented in hexadecimal.

Ex : H00XX (0000 0000 Do-8/7/6/5 Do-4/3/2/1)

Un-21

Digital input status(Di)

The status of digital input represented in hexadecimal.

Ex : HXXXX (000Di-13 Di-12/11/10/9 Di-8/7/6/5 Di-4/3/2/1)

rpm Speed command is displayed in rpm.

Error between position command value and the actual position
feedback.

rpm Display external speed limit command value in rpm.

rev

After power on, it displays pulse command input rotation number in

absolute value.

It displays the torque command as a percentage of the rated torque.

Ex: Display. 50.Means current motor torque command is 50% of rated
torque.
When Cn002.2=0(Auto gain adjust disabled), it displays the current
preset load inertia ratio from parameter Cn025.
x0.1
When Cn002.2=1(Auto gain adjust enabled), it displays the current
estimated load inertia ratio.
%

3-8

3-2-2 Diagnostic function

Following diagnostics parameters are available:
Parameter
Signal
dn-01
dn-02
dn-03
dn-04
dn-05
dn-06
dn-07
dn-08
dn-09

Name and Function

Control mode display
Output terminal status
Input terminal status
Software version (CPU version)
JOG mode operation
Reserve function
Auto offset adjustment of external analog command voltag
Servo model code
ASIC software version display

dn-01 (Control Mode Display)

Access dn-01 to display the selected control mode.
Control mode display description is listed in the table below:
Control Mode

dn-01 ( Control mode display)

Torque controlT
Speed controlS
Position control
(External pulse command)Pe
Position/Speed control switchPe/S
Speed/Torque control switchS/T
Position/Torque control switchPe/T
Position control
(Internal position command) Pi
Internal Position / Speed control
switchPi/S
Internal Position / Speed control
switchPi/T

3-9

dn-02 (Output terminal status)

Use dn-02 to check the status of output terminals.
Output status display is described below:

When output terminal signal has a low logic level (close loop with IG24),
the corresponding LED will be on.
When output terminal signal has a high logic level (open loop with IG24),
the corresponding LED will be off.
Table below shows the functions of the digital outputs.
DO-1~DO-4 are programmable outputs. Default settings are shown below.
DO-5~DO-8 are fix function outputs. ( non-programmable)
For programmable output list see section 5-6-1.
LED No.
1
2
3
4
5
6
7
8

Output terminal number

DO-1
DO-2
DO-3
DO-4
DO-5
DO-6
DO-7
DO-8

Default function
RDY
ALM
ZS
INP
LM/A0
PC/A1
ST/A2
BB/A3

Note: To set the logic state (High or Low) of for programmable digital outputs refer
to section 5-6-1.
For the DO-5~DO-8 ( non-programmable) terminals are active when logic is low.

3-10

dn-03 (Input terminals status)

Use dn-03 to check the status of Input terminals.
Digital Input status display is described below:

10

LED Number

When Input terminal signal has a low logic level (close loop with IG24), the corresponding LED will be on.
When Input terminal signal has a high logic level (open loop with IG24), the corresponding LED will be off.
Table below shows the functions of the digital input.
DI-1 ~ DI -10 are programmable Inputs. Default settings are shown below.
For programmable function list see section 5-6-1.
LED Number
1
2
3
4
5
6
7
8
9
10

Input terminal number

DI-1
DI -2
DI -3
DI -4
DI -5
DI -6
DI -7
DI -8
DI -9
DI -10

3-11

Default function
SON
ALRS
PCNT
CCWL
CWL
TLMT
CLR
LOK
EMC
SPD1

dn-04 (Version of Software)

Use dn-04 to view the current software version of the Servo drive.
Software version can be checked as below:
Step

Keys

Power On

Description

LED Display

On power on Drive Status is displayed.

Press MODE-Key twice to view diagnostics parameter dn-01.

Press INCREMENT-Key 3 times to display dn-04.

Press ENTER-Key for 2 seconds to view the software version.

(Software version: 2.00)

Press MODE-Key once to return to dn-04 and parameter

selection.

3-12

dn-05 (JOG Operation)

Use dn-05 to JOG the motor. Jog is activated by following the steps below:
Note: JOG speed is in accordance with setting of Sn201(internal speed command 1).
Ensure that the required speed is set in Sn201 before executing this function.
Warning: Motor will be agitated run as soon as JOG command is activated.
without the need for SON input (Servo On signal).
Step

Key

Power on

LED display

Description

On power on Drive Status is displayed.

Press MODE-Key once to view diagnostics parameter dn-01.

Press INCREMENT-Key 4 times to display dn-5.

Press ENTER-Key for 2 seconds to enter JOG MODE.

Motor will power on immediately.

Press INCREMENT-Key, motor will run in the pre-defined

positive direction.

6
7

Press DECREMENT-Key, motor will run in the pre-defined

negative direction.
Press MODE-Key once to return to dn-05 and parameter
selection.
Motor stoped the excitation immediately.

3-13

dn-07 (Auto offset adjustment of external analog command voltage)

If the external torque or speed analog command is set to 0V and the motor is rotating slowly,
this is due to analog input zero offset, use dn-07 to auto adjust this offset and stop the motor rotating.
Follow the steps below:
Step
1
2

Key
LED Display
Description
Insert a link between analog command terminal SIN(CN1-26) and Analog Ground terminal
AG(CN1-29) before proceeding.
Power on

On power on Drive Status is displayed.

Press MODE-Key twice into diagnostics parameter dn-01.

Press INCREMENT-Key 6 times to display dn-7.

Press ENTER-Key for 2 seconds to enter dn-07

Press INCREMENT-Key once to set to 1

(Enable auto offset adjustment).

To save the altered preset value and activate auto offset adjust,
Press the ENTER- Key for 2 seconds until SETis displayed
briefly and then display is returned to parameter dn-07.
To save this offset value, please select parameters Tn104 or
Sn217 as required and press the ENTER-Key.
Tn107 for analog torque command.
Sn217 for analog speed command.

3-14

dn-08 (Servo motor Model Code display)

Use dn-08 to display servo motor code and check the servo drive and motor compatibility according to the table
below.
If the dn08 preset is not according to the list below then contact your supplier.
The motor model code is stored in parameter Cn30.

dn-08 Display
Cn030 Setting

Motor Standards
Drive Model

Motor Model

H1111

JSMA-SC01AB
JSMA-PSC01AB

H0121
H1121

JSMA-LC03AB
JSMA-PLC03AB

H0122
H1122

JSMA-LC03AH
JSMA-PLC03AH

JSDA-15A

H1141

JSMA-SC04AH

H1151

JSMA-PSC04AB

H1152

JSMA-PSC04AH

H0211
H1211

JSMA-LC08AB
JSMA-PLC08AB

H0212
H1212

JSMA-LC08AH
JSMA-PLC08AH

H1221

JSMA-SC04AB

Speed
(rpm)

0.1

3000

Encoder
Specification
2500
2500

0.3

3000
8192

JSMA-SC04AB

H0142

Watt
(KW)

2500

0.4
(Rated 3.5A)

3000

0.4
(Rated 2.5A)

3000

0.75

3000

8192
2500
8192
2500
8192

0.4
(Rated 3.5A)

2500
3000

H0222

JSMA-SC04AH

8192

H1231

JSMA-SC08AB
JSMA-PSC08AB

2500

H0232
H1232

JSDA-20A

H0241
H1241
H0242
H1242
H0251
H1251
H0252
H1252

JSMA-MA05AB
JSMA-PMA05AB
JSMA-MA05AH
JSMA-PMA05AH
JSMA-MH05AB
JSMA-PMH05AB
JSMA-MH05AH
JSMA-PMH05AH

H1261

JSMA-(P)SC04AB

H1262

0.75

3000

JSMA-SC08AH
JSMA-PSC08AH

8192
2500
3000
8192
0.55

0.4
(Rated 2.5A)

JSMA-(P)SC04AH

3-15

1500

2500

1500

8192
2500

3000
8192

dn-08 Display
Cn030 Setting

Motor Standards
Drive Model

Motor Model

Watt
(KW)

Speed
(rpm)

0.75

3000

Encoder
Specification

H0312
H1312

JSMA-SC08AB
JSMA-PSC08AB
JSMA-SC08AH
JSMA-PSC08AH

H0321
H1321

JSMA-MA10AB
JSMA-PMA10AB

H0322
H1322

JSMA-MA10AH
JSMA-PMA10AH

8192

H0331
H1331

JSMA-MB10AB
JSMA-PMB10AB

2500

H1311

H0332
H1332

JSDA-30A

2500
8192
2500
1000

2000
JSMA-MB10AH
JSMA-PMB10AH

8192
1.0

H0341
H1341

JSMA-MH10AB
JSMA-PMH10AB

H0342
H1342

JSMA-MH10AH
JSMA-PMH10AH

8192

H0351
H1351

JSMA-MC10AB
JSMA-PMC10AB

2500

H0352
H1352

JSMA-MC10AH
JSMA-PMC10AH

8192

H0511
H1511

JSMA-MA15AB
JSMA-PMA15AB

2500

H0512
H1512

JSMA-MA15AH
JSMA-PMA15AH

8192

H0521
H1521

JSMA-MB15AB
JSMA-PMB15AB

2500

JSDA-50A

2500
1500

3000

1000

1.5

2000

H0522
H1522

JSMA-MB15AH
JSMA-PMB15AH

8192

H0531
H1531

JSMA-MC15AB
JSMA-PMC15AB

2500

H0532
H1532

JSMA-MC15AH
JSMA-PMC15AH

3000
8192

3-16

dn-08 Display
Cn030 Setting

Motor Standards
Drive Model

Motor Model

H0541
H1541

JSMA-MB20AB
JSMA-PMB20AB

H0542
H1542

JSMA-MB20AH
JSMA-PMB20AH

JSDA-50A

Watt
(KW)

Speed
(rpm)

Encoder
Specification
2500

2000
8192
2.0

H0551
H1551

JSMA-MC20AB
JSMA-PMC20AB

H0552
H1552

JSMA-MC20AH
JSMA-PMC20AH

8192

H0711
H1711

JSMA-MB30AB
JSMA-PMB30AB

2500

H0712
H1712

JSMA-MB30AH
JSMA-PMB30AH

2500
3000

H0721
H1721

JSDA-75A

2000
8192

JSMA-MC30AB
JSMA-PMC30AB

3.0

2500
3000

H0722
H1722

JSMA-MC30AH
JSMA-PMC30AH

H0732
H1732

JSMA-MH30AH
JSMA-PMH30AH

H0822
H1822

JSMA-MH44AH
JSMA-PMH44AH

4.4

H0832
H1832

JSMA-HH30AH
JSMA-PHH30AH

3.0

H0922
H1922

JSMA-MH55AH
JSMA-PMH55AH

5.5

H0932
H1932

JSMA-HH44AH
JSMA-PHH44AH

4.4

H0A12
H1A12

JSMA-MH75AH
JSMA-PMH75AH

7.5

H0A22
H1A22

JSMA-HH55AH
JSMA-PHH55AH

5.5

H0B12
H1B12

JSMA-MH110AH
JSMA-PMH110AH

11.0

JSMA-MH150AH
JSMA-PMH150AH

15.0

JSMA-HH75AH
JSMA-PHH75AH

7.5

H0B22
H1B22
H0B32
H1B32

JSDA-100A

JSDA-150A

JSDA-200A

JSDA-300A

8192

3-17

1500

8192

1500

8192

1500

8192

1500

8192

1500

8192

Chapter 4 Trial Operation

Before proceeding with trial run, please ensure that all the wiring is correct.
Trial run description below covers the operation from keypad and also from an external controller such as a PLC.
Trial run with external controller speed control loop (analog voltage command) and position control loop
(external pulse command).
(1) No-load servo motor. Trial run (Reference:4-1)
A. Servo Drive wiring and motor installation

B. Purpose of trial run

P o w e r W in in g

Confirm if the items below are correct:

Drives power cable wiring
Servo Motor wiring
Encoder wiring
Setting servo motor rotation direction and speed
S V -M o to r

M o tio n T a b le

(2) No-load servo motor with a host controller.

Trial run (Reference:4-2)

A. Servo drive wiring and motor installation

B. Purpose of trial run

Confirm if the items below are correct:

M o w e r W in in g

Control signal wiring between host controller and servo

C o n n e c t to
H o s t C o n tro lle r

drive.
Servo motor rotation direction, speed and rotating
number .
Brake function, operation limit function and protection
function.

S V -M o to r

M o to r T a b le

(3) Servo motor connected to load and controlled by a host controller. Trial run (Reference:4-3)
A. Servo drive wiring and motor installation

B. Purpose of trial run

P o w e r W in in g

C o n n e c t to
H o s t C o n tro lle r

S V -M o to r

Confirm if the items below are correct:

Servo motor rotation direction, speed and
mechanical operation range.
Set related control parameters.

M o tio n T a b le

4-1

4-1 Trial Operation Servo motor without Load

To carry out a successful trial run follow the steps below and ensure that drive wiring is correct and as specified.

Warning!
In order to prevent potential damage,prior to trial run ensure that the driven
mechanism, couplings and belts etc are disconnected from the motor.

1. Installation of servo motor.

Ensure that the motor is installed securely so that there is no movement and vibration during trial run.
2. Wiring.
Check servo drive motor power connections and motor encoder connection.
No control signal wiring is required of this stage thus remove connector (CN1) from the servo drive.
3. Servo drive power.
Apply power to servo drive. If the display showed any Alarm message as below, please refer to chapter 8
to identify the cause.

AL-14 is caused by Input terminals CCWL (Counter clockwise Limit) and CWL (Clockwise Limit)
being activated at the same time.
See (the default setting of high or low input logic state according to the description in section 5-6-1 ).
Because of the alarm, the servo can not operate normally.
Set the parameter Cn002.1=1 to disable the drive limit function temporarily during trial run period.

4-2

Steps for setting parameter Cn002.1 ( CCWL &CWL Rotation limit selection).
Setp

Keys

Power on

LED Display

Description

On power on Drive Status is displayed.

Press MODE-Key 4 times to display Cn001.

Press INCREMENT-Key once to display Cn002.

Press ENTER-Key for 2 secs to display the preset value of

Cn002. Note: Cn 002 includes 4 digits corresponding to
Cn002.0,Cn002.1,Cn002.2 & Cn002.3.

Press ENTER-Key once to move to the 2nd digit for (Cn 002.1).

Press INCREMENT- Key once to adjust the 2nd digit to 1.

Disable the function of external limits CCWL and CWL.

To save the setting value by

Press the ENTER- Key for 2 seconds until SETis displayed
briefly and then display is returned to parameter Cn-002.

After accomplish these steps, reset the power. If there are any other alarms then
refer to section 8-2 (Clearing Alarms). Once there is no alarms then operate the drive again.
If any of the alarms can not be cleared, please contact your local supplier for assistance.
4. Mechanical Brake Release.
When a brake type servo motor is used then must release the brake before starting trial run
by applying 24vdc voltage to brake terminals.
5.

Keypad Trial run (JOG function).

Jog function can be used to check if motor speed and rotation direction is correct.
Parameters Sn 201(internal speed command 1) and Cn004 (motor rotation direction selection)
Can be used to set the required speed and direction.

Warning!
Set the required JOG speed before the trial run otherwise the motor will run at the default speed set in
parameter Sn201(internal speed command 1).
Warning!
Regardless of external SON (servo on) is active of not, Servo motor will get excitation as soon as JOG is
activated.

4-3

Steps for setting JOG function:

Step

Keys

Power on

LED Display

Description
On power on Drive Status is displayed.

Press MODE-Key twice to view diagnostics parameter dn-01.

Press INCREMENT-Key 4 times to display dn-5.

Press ENTER-Key for 2 seconds to enter JOG MODE.

Motor will power on immediately.

Press INCREMENT-Key, motor will run in the pre-defined

positive direction.

Press DECREMENT-Key, motor will run in the pre-defined

negative direction.

Press MODE-Key once to return to dn-05 and parameter

selection.
Motor power will be turned off immediately.

4-4

4-2 Trial Operation for Servo motor without Load from Host Reference
Check and ensure that all power connections to the drive and motor and control signal connection between
the host controller and the drive are correct.Motor must be mechanically disconnected from the load.
Following section describes the trial run when using a host controller such as a PLC.
Two trial runs have been discussed. Speed control mode ( Section B) and Position control mode ( Section C).
Section A shows the connections and SON signal (servo on) requirements for both trial runs.

A. Launching Servo motor

Example wiring diagram:
Speed Control(Cn001=1)

Position Control(Cn001=2)
Servo Drives

Servo Drives
IP24
DICOM
SON

CN1-45
DICOM

CN1-47
SON

CN1-1

CCWL CN1-4
CWL CN1-5
IG24
SIN

IP24

CN1-48

CN1-47
CN1-1

Servo Motor

CCWL CN1-4

Servo Motor

CWL CN1-5

IG24
Pulse
/ Pulse

CN1-26

Sign

AG

CN1-45

CN1-32

/ Sign

CN1-48
CN1-14
CN1-15
CN1-16
CN1-17

a. Disable Analog Input command terminals.

Speed control mode: Link analog input terminal SIN to 0V terminal (AG).
Position control mode: Link external pulse command terminals Pulse to /Pulse and Sign to
/Sign.
b. Enable Servo ON Signal
Connect SON terminal to IG 24 (0V) terminal (Digital Ground).
On drive power up servo will be turned on. Now check for any Alarms. If any alarms then refer to
Chapter 8-2 for how to reset the Alarms.

To control the motor operating and stop, please input Torque/Speed/Position command after
Servo ON.

When input Torque/Speed/Position command, Please do not control the motor operating and stop
by using servo on signal.

4-5

B.

Trial run in Speed control mode(Cn001=1).

1. Wiring check:
Check and ensure that all power cable and control signal connections are correct as shown below.
To be able to adjust the speed for test connect a potentiometer between terminals SIN (analog input voltage)
and AG (Analog Ground). Set the analog input voltage to 0V. (No speed reference).
Servo Drive
IP24
DICOM
SON

CN1-45
CN1-47
CN1-1

CCWL CN1-4

Servo Motor

CWL CN1-5
IG24
SIN
AG

2.

CN1-48
CN1-26
CN1-32

Apply Servo on.

Apply power to the drive and activate (SON) signal by switching SON terminal to IG24 (input digital Ground).
If the motor rotates slowly, while the speed analog input voltage is 0 volts
then use dn-07 function to auto offset adjustment for the analog input value. (refer to section 3-2-2).

3. Check the relationship between motor speed and the analog input speed command.
Increase the analog speed input voltage gradually (by potentiometer) and monitor the actual motor speed by
parameter Un0-01.
Check if motor rotation direction is correct and if necessary set it by parameter Cn004.
Check for correctness of analog speed command ratio in relation to the preset in parameter (Sn216) and
analog speed command limit as set in parameter (Sn218).
Finally, switch off SON signal (turn off the servo motor).

4-6

4. Connection with a host controller.

Check and ensure that the wiring for the servo drive and host controller, speed analog signal input (SIN), and
encoder output (PA, /PA, PB, /PB, PZ, /PZ) are all correct and according to the diagram below:

5. Confirm the rotation number and encoder output of Servo Motor.

Use parameter Un-14 to check if the Motor feed back (number of revolutions) per minute is correct and the
same as number of revolutions sent by the host controller.
If there is any difference then check and make sure that parameter Cn005 ( Encoder ppr) is set correctly.
Once this is complete remove SON signal to switch off power to the motor.

4-7

C.

Position control mode trial run (Cn001=2).

1. Wiring:
Check and ensure that all power connections to the drive and motor and control signal connections are correct as
diagram below.

2. Setting electronic gear ratio.

Set electronic gear ratio parameters Pn302~Pn306 as required for the positioning application.
(refer to section 5-4-3).
Note: Electronic gear ratio parameter can be used to scale the command output pulse.
This would be useful in transmission applications where move distance per move command pulse
has to be scaled due to mechanical requirements.
3. Apply Servo on.
Apply power to the drive and activate (SON) signal by switching SON terminal to IG24 (input digital Ground).
4. Confirm motor speed, direction and number of revolutions.
Apply a low-speed pulse command from the host controller to the servo drive so that the servo motor
operates at low-speed.

Compare the number of pulses per revolution from parameters Un-15 ( motor feed back pulse ppr)
and Un-17 (Input command ppr) these should be the same.

Compare the number of revolutions using parameters Un-14 ( motor feed back rotation number) and
Un-16 (pulse command rotation number) these should be the same.

If there are differences then adjust electronic gear ratio parameters Pn302~Pn306 as required and test
again until the result is satisfactory.
If the direction of motor rotation is incorrect then check and if necessary set parameter Pn 301.0
(position pulse command types).
Also check and if necessary set parameter Pn314 (Position command direction selection).
Once the test result is correct then remove SON signal. (Power to the motor is switched off).

4-8

4-3 Trial Operation with the Servo motor Connected to the Machine

Servo drive parameters must be set correctly otherwise damage to machinery and potential injury
may result.
Do not close to the machine after temporary power loss, the machine may restart unexpected.

Please take the measures highlighted in the section below before trial run with load.

Consider the Mechanical system requirements and set the parameters appropriate for control by the host
controller.

Ensure that the rotation direction and speed are suitable for the Mechanical system.

Steps required for Trial run.

1. Ensure that the ServoDrive Power is off.
2. Connect the servo motor to the load shaft.
Refer to Chapter 1-5 to check the installation guidelines for the servo motor.
3. Gain adjustment for the servo control loop.
Refer to Chapter 5-5 for details.
4. Trial run with a host controller.
Run command is to be signaled by the host controller.
Refer to Chapter 4-2 to choose the required trial run mode (Speed control or position control modes)
according to the application and set and adjust the parameters if necessary for the application.
5. Repeat adjusting and record the set parameter values.
Repeat steps 3 and 4 until the mechanical system is operating satisfactorily then
record the Gain value and the parameters changes for the future use.

4-9

Chapter 5 Control Functions

5-1 Control Mode Selection
There are three control modes in the servo drive, torque, speed and position modes can be selected
individually or as a combination according to the selection table below:
Parameter

Name

Setting
0
1

Cn001

Control
mode
selection

Description
Torque control
To use one analog voltage command signal to control
torque. Please refer to 5-2.
Speed control
Input contacts SPD1 and SPD2 can be used to select 4
-steps of speed. Please refer to section 5-3-1.
Position control (External pulse command)
Four separate selectable pulse command types are
possible to control position. Please refer to section
5-4-1.
Position / Speed control switch
Input contact MDC can be used to switch between
position & speed control. Please refer to section 5-6-2.
Speed / Torque control switch
Input contact MDC can be used to switch between
speed
& torque control. Please refer to section 5-6-2.
Position / Torque control switch
Input contact MDC can be used to switch between
position & torque control. Please refer to section
5-6-2.
Position control (internal position command)
Input contacts POS 1~POS 4 can be used to select 16
programmable preset position commands to control
position. Please refer to 5-4-2.
Internal Position / Speed control switch
Input contact MDC can be used to switch control mode
between position and speed, please refer to chapter
5-6-2.
Internal Positin / Torque control switch
Input contact MDC can be used to switch control mode
between position and torque, please refer to chapter
5-6-2.

New setting will become effective after re-cycling the power.

5-1

Default
Value

Control
Mode

ALL

5-2 Torque mode

Torque mode is used in applications such as printing machines, coil wiring machines, injection molding
machines and specific application that requiring torque control.
Diagram below shows the torque control process diagram.

Analog voltage torque command is applied to the drive input terminals as shown below:

Caution!
Care should be taken in selection of required torque direction CW/CCW.
Please refer to Chapter 5-2-4.

5-2

5-2-1 Analog Torque command Ratio.

Analog torque command ratio can be used to adjust the relationship between
Input voltage torque command and actual torque command.
Parameter

Name

Default

Unit

Setting range

Control Mode

Tn103

Analog torque
command ratio

300

%/10V

0~300

Setting example: refer to the following diagram.

1. With Tn103 set to 300, a torque command input voltage of 10V, corresponds to
300% of rated torque. For input voltage of 5V, actual torque command will be 150% of rated torque.
2. With Tn03 set to 200 , a torque command input voltage of 10V, corresponds to
200% of rated torque. For input voltage of 5V, actual torque command will be 100%.

300
Torque
200
Command (%)
100
-10

-5
-100

10
5
Input Voltage (V)

-200
-300

5-3

Slope is set by Tn103

5-2-2 Adjusting the analog torque command offset

For a torque command of 0V, motor could possibly be rotating slowly.
To rectify this effect by adjust offset value in parameter Tn104 or use auto offset adjust feature.
(Please refer to section 3-2-2).
Note : To check and set the offset to zero, insert a link between analog torque command contact
SIN(CN1-26) and analog ground contact AG (CN1-29).

Parameter

Name

Default

Unit

Setting range

Control mode

Tn104

Analog torque
command offset

mV

-10000~10000

Input Voltage (V)

Bias Voltage

Torque Command (%)

5-4

5-2-3 Torque command linear acceleration and deceleration

An smooth torque command can be achieved by enabling acceleration/Deceleration parameter Tn101.
Parameter

Name

Setting

Tn101

Linear acceleration/
deceleration method

Description

Disable

Enable

Control
mode
T

Torque command acceleration/deceleration time,

is the time taken for the torque to rise from zero to the required level by Tn102.
As per diagram below:Parameter

Name

Default

Unit

Setting Range

Control
mode

Tn102

Linear acceleration
/deceleration time period

msec

1~50000

New setting will become effective after re-cycling the power.

Torque Command
Rated Torque
Command

Required Torque
Command

Tn102
Setting examples:
(1) To achieve 50% of rated torque output in 10msec:

Tn102 = 10(msec)

100%
= 20(msec)
50%

(2) To achieve 75% of rated torque output in 10msec:

Tn102 = 10(msec)

100%
= 13(msec)
75%

5-5

Time (ms)

5-2-4 Definition of torque direction

In torque mode, torque direction can be defined by one of the following three methods.
(1) Input contacts RS1, RS2. (torque command CW/CCW selectable by programmable input)
(2) Parameter Cn004. (motor rotation direction )
(3) Input contact TRQINV. (reverse torque command)
Caution !
All 3 methods can be active at the same time.
User must ensure that correct selections are made for these three selections.
Control
mode

Input Contact
Description
RS2
RS1
0
0
Zero torque
Rotation in the current torque command
0
1
direction
Reverse the current torque command direction
1
0
1
1
Zero torque

Note: RS2 and RS1 contact status 1 (ON) and 0 (OFF).

Please check 5-6-1 to set the required high /Low signal levels ( PNP/NPN) .
Parameter
Signal

Name

Motor rotation
direction (load end)

Control
mode

Description

Setting

No.

Torque Control

Speed Control

Counter Clockwise(CCW)

Counter Clockwise (CCW)

Clockwise(CW)

Counter Clockwise (CCW)

CCW

S/T

Cn004
CW

Counter Clockwise (CCW)

Clockwise (CW)

Clockwise (CW)

Clockwise (CW)

Input contact TRQINV

Description

Rotation in current torque command

direction

Reverse torque command direction

Control
mode
T

Note: Input contacts status 1 (ON) and 0 (OFF).

Please refer to 5-6-1 to set the required high /Low signal levels ( PNP/NPN) selection.

5-6

5-2-5 Internal Torque Limit

In torque Control mode, user can set internal torque limit values as required.
Set as below:Parameter

Name
CCW Torque
command limit
CW Torque
command limit

Cn010
Cn011

Default

Unit

Setting range

Control mode

300/200

0~300

ALL

-300/-200

-300~0

ALL

5-2-6 Limiting Servomotor Speed during Torque Control

In torque control, input contacts SPD1 and SPD2 can be used for selecting one of the two
methods below for setting speed limits.
(1) External Analog command ( Default) Signal is applied to terminals PIC & AG ( pins 27& 29 on CN1)
(2) Selection of Three presentable Limits (Tn105~Tn107) according to the table below.
Caution! For achieving smooth speed response please refer to section 5-3-6.
Input contact SPD2

Input contact
SPD1

Speed limit command

Control
mode

External analog
command
PIC(CN1-27)
Internal speed limit1
Tn105
Internal speed limit2
Tn106
Internal speed limit3
Tn107

Note: Input contacts status 1 (ON) and 0 (OFF).

Please check 5-6-1 to set the required high /Low signal levels ( PNP/NPN) selection.
Below is the external analog speed limit command wiring diagram:

Internal presentable speed limit parameters for torque control mode are listed below:
These preset limits apply to both CW & CCW directions.
Parameter

Name

Default

Unit

Setting range

Control mode

Tn105
Tn106
Tn107

Internal speed limit 1

Internal speed limit 2
Internal speed limit 3

100
200
300

rpm
rpm
rpm

0~3000
0~3000
0~3000

T
T
T

P.S also refer to page 6-11 for detail.

5-7

5-2-7 Additional torque control functions

Torque Output Monitor
When the torque level in CW or CCW directions becomes greater than the value set in
Tn108 (torque level monitor value), the output contact INT is active.
Parameter

Name

Default

Unit

Setting range

Control mode

Tn108

Torque output monitor

level

100

0~300

ALL

Note: Input contacts status 1 (ON) and 0 (OFF).

Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

Torque Smoothing Filter

Torque vibration can be diminution by setting an appropriate value in Cn034 (Torque command smoothing
filter), In the other hand, this will cause a delay in the response time of the torque loop.

Parameter
Cn034

Name
Torque smoothing
filter

Default

Unit

Setting range

Control mode

Hz

0~1000

ALL

5-8

5-3 Speed Mode

Speed Mode is necessary for applications that require precisely speed control, such as weaving, drilling
and CNC type machines.Diagrams below shows the speed control system in two parts.
First stage shows Speed processing and conditioning and the second stage shows the Speed controller
With PI/P control modes, and controller1&2 selection and interface with torque control stage.

Speed Command Processor

Analog Speed Command

Host Controllor

A/D

Once Smooth
AC/deceleration

Analog Speed Command Limit

Ratio
Sn216

Sn206

Sn218

Sn217

Linear
AC/deceleration

Bias Adjusting

Speed
Rotating Direction
Cn004
Input Contact
SPDINV

Speed Feed Back

Sn208~Sn210
Cn005

Sn201~Sn203

Encoder Signal
Encode-ratio Output

Internal Speed Command

Speed Controller

S-Curve
AC/deceleration
Sn205
AC/deceleration Method

Speed Controller
Analog Torque Limit

A/D

Speed Controller 1
Resonance filter

Speed Command
From Speed
Processor

Analog Torque Limit

Sn211, Sn212
Torque Control
Loop

Cn013, Cn014
Internal Torque
Limit

Speed Controller 2
Speed
Feed Back
Smooth Filter
Cn032

Sn213, Sn214

Gain switch method

Cn010, Cn011

Input Contact

Cn015~Cn024
Speed Feed Back

5-9

5-3-1 Selection for speed command

In Speed control, input contacts SPD1 and SPD2 can be used for selecting one of the two methods below
for setting speed limits.
(1) External Analog command (Default) : Analog signal is input from terminals SIN & AG (pins 26& 29 on
CN1)
(2) Internal speed command: Selection of Three presentable Limits according to the table below.
.
Input Contact SPD2 Input Contact SPD1

Speed Command

External analog command

SIN(CN1-26)

Internal speed command 1

Sn201

Internal speed command 2

Sn202

Internal speed command 3

Sn203

Control
Mode

Note: Input contacts status 1 (ON) and 0 (OFF).

Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.
Diagram below shows the external analog speed command wiring:

Internal presetable speed limit parameters for speed command mode are listed below:
These preset limits apply to both CW & CCW directions.

Parameter
Sn201
Sn202
Sn203

Name
Internal speed
command 1
Internal speed
command 2
Internal speed
command 3

Default

Unit

Setting range

Control mode

rpm

-3000~3000

100
200
300

5-10

5-3-2 Analog speed command Ratio

Analog speed command ratio can be used to adjust the relationship between
Input voltage speed command and actual speed command.
Parameter

Name

Default

Unit

Setting range

Control mode

Sn216

Analog speed
command ratio

3000

rpm/10V

100~4500

Setting Example:
(1) With Sn216 set to 3000, a speed command input voltage of 10V, corresponds to
3000rpm; for an input voltage of 5V speed command will be 1500rpm.
(2) With Sn216 set to 2000, a speed command input voltage of 10V, corresponds to 2000rpm,
for an input voltage of 5 volts speed command will be 1000rpm.

5-3-3 Adjusting the analog reference offset

For a speed command of 0V, motor could possibly be rotating slowly.
To rectify this effect by adjust offset value manually in parameter Sn217 or use auto offset adjust feature.
(Please refer to section 3-2-2).
Note : To check and set the offset to zero, insert a link between analog torque command contact
SIN(CN1-26) and analog ground contact AG (CN1-29).

Parameter
Sn217

Name
Analog speed
command offset
adjust

Default

Unit

Setting range

Control mode

mV

-10000~10000

5-11

Refer to the following diagrams:

Input Voltage (V)

Input Voltage (V)

Bias Voltage

Bias Voltage
Adjusting Value

Speed Command(rpm)

Speed Command(rpm)

5-3-4 Analog reference for speed command limit

A maximum limit for analog speed can be set by Sn218.
Parameter

Name

Default

Unit

Setting range

Control mode

Sn218

Analog speed
command limit

Rate rpm
x 1.02

rpm

100~4500

5-3-5 Encoder Signal Output

Servo motor encoder pulse signal can be output to a host controller to establish an external control loop.

Set the required encoder Pulse Per Revolution (PPR) in parameter Cn005.
Default output value is the actual encoder PPR.

5-12

Parameter

Name

Default

Unit

Setting range

Control
mode

Cn005

Encoder pulse
output scale

Encoder
Pulse Per
Revolution

pulse

1~ Encoder PPR

ALL

New setting will become effective after re-cycling the power.

Encoder pulse output terminal description:
Pin
PA
/PA
PB
/PB
PZ
/PZ

Pin NO. of
CN1

Name
Encoder pulse output A Phase
signal
Encoder pulse output /A Phase
signal
Encoder pulse output B Phase
signal
Encoder pulse output /B Phase
signal
Encoder pulse output Z Phase
signal
Encoder pulse output /Z Phase
signal

90

Control
mode

CN1-35
CN1-36
CN1-37

ALL

CN1-38
CN1-39
CN1-40

90

PA

PA

PB

PB

PZ

PZ
TIME

TIME

5-13

5-3-6 Smoothing the speed command

Sn205 can be used to eliminate speed overshoot and motor vibration by selecting one of the
acceleration /deceleration methods which is suitable for the application from the table below.
Parameter

Name

Sn205

Speed
command
accel/decel
smooth
method

Setting

Control
mode

Description

Disable accel/decel smooth function

Smooth accel/decel according to parameter Sn206

Linear accel/decel according to parameter Sn207

S-curve accel /decel according to parameter Sn208

Above three methods of Acceleration/deceleration are described below.

(1)Speed command smooth ac/deceleration:

Set Sn205=1 to enable the use of speed command smooth acceleration/deceleration function.
Parameter

Name

Default

Unit

Setting range

Control
mode

Sn206

Speed command smooth

accel/decel time Constant

msec

1~10000

Smooth acceleration/deceleration time corresponds to the time in which the speed command increases from 0 to
63.2% as shown in diagram below.

5-14

Setting example:
(1) To achieve 95% of speed command output in 30msec:
Set

Sn206 =

30(msec)
= 10(msec)
- ln(1- 95%)

(2) To achieve 75% of speed command output in 30msec:

Set Sn206 =

30(msec)
= 22(msec)
- ln(1 - 75%)

ln= Natural log

(2)Speed command linear acceleration/deceleration function:

Set Sn205=2 to enable the use of speed command linear acceleration/deceleration function.
Parameter

Name

Default

Unit

Setting range

Control
mode

Sn207

Speed command linear

accel/decel time constant

msec

1~50000

Linear acceleration/deceleration time corresponds to the time in which the speed increases (linearly)
from zero to the rated speed. As shown in the diagram below.
Speed Command
Rated Speed Command

Current Speed Command

Sn207

Setting examples:
(1) To achieve 50% of rated speed output in 10msec:
Set Sn207 = 10(msec)

100%
= 20(msec)
50%

(2) To achieve 75% of rated speed output in 10msec:

Set Sn207 = 10(msec)

100%
= 13(msec)
75%

5-15

Time(ms)

S-Curve Speed Command Acceleration/Deceleration:

Set Sn205=3 to enable the use of S-Curve speed command ac/deceleration function.

Parameter
Sn208
Sn209
Sn210

Name
S-Curve speed command
accel/decel time setting
S-Curve speed command
acceleration time setting
S-Curve speed command
deceleration time setting

Default

Unit

Setting range

Control mode

msec

1~1000

200

msec

0~10000

200

msec

0~10000

In applications where normal acceleration/deceleration on ramp up or ramp down bring in vibration of the
mechanical
system. S- curve acceleration/deceleration parameters could help to reduce vibration as diagram below:

Speed Command (rpm)

ts=Sn208
ta=Sn209
td=Sn210

ts

ts

ts

ta

Caution! Setting Rule:

ts
td

ta
t
> ts d > ts
2
2

5-16

Time (ms)

5-3-7 Setting rotation direction

Motor rotation direction in speed mode can be set by parameter Cn004 (Motor rotation direction)and input
contact SPDINV according to the tables below.
Caution!
Both methods can be operated at the same time.
Ensure that these parameters are set correctly for the required direction.
Parameter

Name
Motor rotation
direction (observation
from load side).

No.
0

Control
mode

Description

Setting

Torque control

Speed control

Counter Colckwise (CCW) Counter Colckwise (CCW)

CCW

Colckwise (CW)

Counter Colckwise (CCW)

Cn004

S/T
CW

Input contact
SPDINV

Counter Colckwise (CCW)

Colckwise (CW)

Colckwise (CW)

Colckwise (CW)

Description

Rotation by speed command direction.

Rotation by reverse speed command direction.

Control
mode
S

Note: Input contacts status 1 (ON) and 0 (OFF).

Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-17

5-3-8 Speed Loop Gain

In speed mode there are two speed controller loops,
with separate Gain ( P) and Integral (I) functions.
Speed controllers 1 or 2 can be selected by setting one of the multi- function input terminals,
to selection G-SEL or by setting one of the parameters Cn20-Cn24 as required.
Please refer to section 5-3-11 section B for more details.

Parameter

Name

Default

Unit

Setting range

Control
mode

Sn211

Speed loop gain 1

40

Hz

10~450

Pe/Pi/S

Sn212

Speed loop integral time constant 1

100

x0.2
ms

1~500

Pe/Pi/S

Sn213

Speed loop gain 2

40

Hz

10~450

Pe/Pi/S

Sn214

Speed loop integral time constant 2

100

x0.2
ms

1~500

Pe/Pi/S

Diagram below shows the speed controller.

Setting a high speed loop gain or a lower speed loop integral time provides a faster speed control response
time.
For more details refer to section 5-5.

Kv 1

1
TiS

5-18

Kv: Speed Loop Gain (Hz)

Ti: Speed Loop Integral
Time Constant (sec)

5-3-9 Notch Filter

The function of the Notch filter is to suppress mechanical system resonance.
Resonance occurs due to low mechanical system rigidity (high springiness) of transmission systems used
with servo motors such as couplings, bearings, lead screws, etc.
Enter the mechanical system vibration (resonance frequency) in parameter Cn013 (Notch Filter frequency)
and adjust Cn014 to set the filter bandwidth scaling factor.
Lower the setting of Cn014 value, wider is the notch filter frequency bandwidth. The adjustment required
depends on the application.
Caution!
If Cn013 is set to 0 the Notch filter is disabled.
Parameter

Name

Defaul
t

Unit

Setting range

Control mode

Cn013

Notch Filter frequency

Hz

0~1000

Pi/Pe/S

Cn014

Notch Filter Band Width

Scaling factor

1~100

Pi/Pe/S

5-19

5-20

Q3

Q1

Cn013
(Notch Filter-Frequency

Q2

Response Line for Notch Filter

Resonant Frequency

The Response Line for Resonance

Q1>Q2>Q3
Cn014(Notch Filter-Quality Factor)

Gain

Gain

Frequency

Frequency

Gain

After adding Notch Filter

Frequency

5-3-10 Torque limit of speed control mode

In speed mode, the motor torque limit input contact TLMT could be used to select one of the two methods
below:
(1) Internal toque limit: Using default Cn010 (CCW Torque command limit ) and
Cn011(CW Torque command limit ).
(2) External analog command: Using two separate analog voltage command signals at input terminals
PIC(CN1-27) to limit CCW torque and NIC(CN1-28) to limit CW torque.
As shown in the table below:

Input contact
TLMT

CCW torque command limit

source

CW torque command limit

source

Control
mode

Cn010

Cn011

ALL

External analog command

PIC(CN1-27)

External analog command

NIC(CN1-28)

Pi/Pe/S

Note: Input contacts status 1 (ON) and 0 (OFF).

Please check 5-6-1 to set the required high /Low signal levels ( PNP/NPN) selection.
Caution!
To use external analog torque command limit , If analog torque command limit is greater than
internal torque command limit, the internal torque command limit has the priority over external
analog torque command limit.
Internal Torque command limit is set as below.
Parameter
Cn010
Cn011

Name
CCW torque command limit
CW torque command limit

Default

Unit

Setting range

300 / 200
-300 / -200

%
%

0~300
-300~0

The diagram below shows the external analog torque limit command wiring:

5-21

Control
mode
ALL
ALL

5-3-11 Gain Switched

PI/P control mode selection (Section A)
Automatic gain 1& 2 switch (Section B)
The selection of PI/P control mode switch and Automatic gain 1& 2 switch by parameters or from input
terminals can be used in following conditions.
(1) In speed control, to restrain acceleration/deceleration overshooting.
(2) In position control, to restrain oscillations and decrease the adjusting time.
(3) To decrease the possible noise caused by using Servo Lock function.

(A) Switching between PI/P Control modes

Switch over from PI to P mode is determined by setting of parameter Cn015.0 and according to
the selection options below:
Parameter
Signal

Name

0
1
Cn015.0

PI/P control
mode
switch

2
3
4

Parameter
Cn016
Cn017
Cn018
Cn019

Description

Control
mode

Switch from PI to P if the torque command is

greater than Cn016
Switch from PI to P if the speed command is
greater than Cn017
Switch from PI to P if the acceleration command is
greater than Cn018
Switch from PI to P if the position error is greater
than Cn019
Switch from PI to P by the input contact PCNT.
Set one of the multi function terminals to option 03.

Pi/Pe/S

Setting

Name
PI/P control mode switch by
(torque command)
PI/P control mode switch by
(speed command)
PI/P control mode switch by
(acceleration)
PI/P control mode switch by
(position error value)

Default

Unit

Setting range

Control
mode

200

0~399

Pi/Pe/S

rpm

0~4500

Pi/Pe/S

rps/s

0~18750

Pi/Pe/S

pulse

0~50000

Pi/Pe/S

5-22

(1) PI to P mode switch over by comparing Torque command.

When the Torque command is less than Cn016 PI control is selected.
When the Torque command is greater than Cn016 P control is selected..
As shown in diagram below:

(2) PI to P mode switch over by comparing Speed command.

When the Speed command is less than Cn017 PI control is selected.
When the Speed command is greater than Cn017 P control is selected.
As shown in diagram below:

Speed
PI/P -Mode Switching Condition
(Speed Command)

5-23

(3) PI to P mode switch over by comparing Acceleration command.

When the Acceleration command is less than Cn018 PI control is selected.
When the Acceleration command is greater than Cn018 P control is selected.
As shown in diagram below:
Speed

Cn018
PI/P-Mode Switching Condition
(Acceleration)

Acceleration Command

(4) PI to P mode switch over by comparing Position Error value.

When the Position Error value is less than Cn019 PI control is selected.
When the Position Error value is greater than Cn019 P control is selected.
As shown in diagram below:

(5) PI to P mode switch over by PCNT input contact.

When the PCNT input contact is open PI control is selected.
When the PCNT input contact is closed P control is selected.
Note: Input contacts status 1 (ON) and 0 (OFF).
Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

Switch PI/P
by PCNT input contact

Status of contact PCNT

Enable

0
P control

PI control

5-24

PI control

(B) Automatic gain 1& 2 switching

Selection of Automatic gain 1& 2 switch with different P&I Gains is possible by setting
Parameter Cn 015.1 to one of the selections listed in the table below.
Parameter Cn 020 can be use for setting a switch delay time between different gains. (Gain 1 and 2)
Parameter

Name

Setting
0
1

Cn015.1

Automatic
gain 1& 2
switch

2
3
4

Parameter

Cn020

Cn021
Cn022

Cn023

Cn024

Control
Mode

Description

Switch from gain 1 to 2 if torque command is greater

than Cn021.
Switch from gain 1 to 2 if speed command is greater
than Cn022.
Switch from gain 1 to 2 if acceleration command is
Pi/Pe/S
greater than Cn023.
Switch from gain 1to2 if position error value is
greater than Cn024.
Switch from gain 1 to 2 by input contact G-SEL. Set
one of the multi function terminals to option 15 of
Hn501.

Name
Automatic gain 1& 2
switch delay time.
Automatic gain 1& 2
switch condition
(torque command)
Automatic gain 1& 2
switch condition
(speed command)
Automatic gain 1& 2
switch condition
(acceleration
command)
Automatic gain 1& 2
switch condition
(position error value)

Default

Unit

Setting Range

Control
Mode

x0.2 msec

0~10000

Pi/Pe/S

200

0~399

Pi/Pe/S

rpm

0~4500

Pi/Pe/S

rps/s

0~18750

Pi/Pe/S

pulse

0~50000

Pi/Pe/S

Note: Gain 1 : is consisted of Pn310(position loop gain 1), Sn211(speed loop gain 1 ) and
Sn212(Speed loop integral time 1).
Gain 2 : is consisted of Pn311(position loop gain 2), Sn213(speed loop gain 2) and
Sn214(Speed loop integral time 2 ).

5-25

(1) Automatic gain 1&2 switch condition ( by torque command ).

When torque command is less than Cn021 , Gain 1 is selected.
When torque command is greater than Cn021, Gain 2 is selected
When Gain 2 is active and torque command becomes less than Cn021 system will automatically switch back
to Gain 1 the switch time delay can be set by Cn020.
|As show in the diagram below:

(2) Automatic gain 1&2 switch condition (by Speed command ).

When speed command is less than Cn022 Gain 1 is selected.
When speed command is greater than Cn022 Gain 2 is selected.
When Gain 2 is active and speed command becomes less than Cn022 system will automatically switch back
to Gain 1 the switch time delay can be set by Cn020.
|

As show in the diagram below :

5-26

(3) Automatic gain 1&2 switch condition (by Acceleration command ).

When acceleration command is less than Cn023 Gain 1 is selected.
When acceleration command is greater than Cn023 Gain 2 is selected.
When Gain 2 is active and acceleration command becomes less than Cn023 system will automatically
switch back to Gain 1 the switch time delay can be set by Cn020.
|

As show in the diagram below :

(4) Automatic gain 1&2 switch condition (by Position error value ).
When position error value is less than Cn024 Gain 1 is selected.
When position error value is greater than Cn024 Gain 2 is selected.
When Gain 2 is active and position error value becomes less than Cn024 system will automatically switch
back to Gain 1 and the switch time delay can be set by Cn020.
|

As show in the diagram below :

Speed

Cn024
Switching Condition of
2 Stages Gain Mode
(Position Error Value)

Position Error Value

Cn020
Delay Time

Gain 1

Gain 2

5-27

Gain 1

(5) Automatic gain 1&2 switch condition by G-SEL input contact.

When the G-SEL input contact is open Gain 1 is selected.
When G-SEL input contact is closed Gain 2 is selected.
When G-SEL input contact opens again then Gain 1 is selected and switch delay time can be set by Cn20.
As show in the diagram below :

Use Input Contact G-SEL to

Switch 2 Stages Gain Mode

Input Contact G-SEL Statu

Motion

1
0

Cn020
Delay Time

Gain 1

Gain 2

Gain 1

Note: Input contacts status 1 (ON) and 0 (OFF).

Please refer to 5-6-1 for setting required high /Low signal levels (PNP/NPN) selection.

5-28

5-3-12 Other Functions

When the speed level in CW or CCW directions becomes greater than the value set in
Cn007 (Speed reached preset), the output contact INS operates.

Speed reached preset

Parameter
Signal

Name

Default

Unit

Setting Range

Control Mode

Cn007

Speed reached
preset

Rated rpm
1/3

rpm

0~4500

S/T

Note: Input contacts status 1 (ON) and 0 (OFF).

Please check section 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-29

Zero Speed preset

When the speed is less than the speed set in Sn215 (Value of ZS), the output contact ZS operates.
Parameter
Signal
Sn215

Name

Default

Unit

Setting Range

Control Mode

Value of zero speed

50

rpm

0~4500

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check section 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

To Zero the speed command according to preset level in Sn215 set Sn204 to selection 1.
Parameter
Signal

Name

Sn204

Zero Speed
selection

Setting

Description

No action

Regard Speed command as Zero. (According to Sn215

setting).

Control
Mode

Speed Command

Zero speed
preset level

Set the speed

preset level as
Zero speed

Previous Speed Command

Adjusted Speed Command

Servo Lock
In speed mode: the Servo Lock is used to lock servo motor when input voltage command is not at 0V.
When input contact LOK operates: The control mode changes to internal position control mode, it temporarily
stop motor rotation. Please refer to section 5-6-1 for setting input contact LOK function.

5-30

Speed Feed Back Smooth Filter

When there is system abnormal vibration or noise, Set Cn032 (speed feed back smoothing filter)
to restrain vibration or noise. Addition of this filter will delay the speed response of servo system.
Parameter
Signal

Name

Default

Unit

Setting Range

Control Mode

Cn032

Speed feed back

smoothing filter

500

Hz

1~1000

Pe/Pi/S

5-4 Position mode

Position control mode is used for high-precision applications on machinery such as machine tools.
The Position control mode offers two methods of control.

External pulse input position command

Internal position command.

In external pulse command input mode, the positioning command is signaled to the drive by a host Controller
to achieve a fixed position.
In internal position command mode, 16 preset position commands can be set by parameters
(Pn317~Pn364),
and can be activated by use of input contacts POS1 ~ POS4.
Set parameter Cn001 (control mode selection) as required according to the table below.
Parameter
Signal

Name

Setting
2

Cn001

Control mode
selection
6

Control
Mode

Description
Position control (External pulse command)
Using one pulse command signal to control position.
Please refer to 5-4-3.
Position control (Internal pulse command)
Use input contacts to select 16 programmable preset
position commands. Please refer to 5-4-2.

ALL

New setting will become effective after re-cycling the power.

The diagram below shows the position loop control. Detailed functions are described in the following chapters.
Control Mode
Selection
Internal position
Command
Cn317~Cn364
Input contacts
POS1~ POS4
PTRG, HOLD
External Pulse External pulse
Command
command mode
Pn301

Internal Position
Command Mode

Feed for ward gain

Pn312

Cn001

Pn370
Pn371

Pn316
Electric Gear
Pn302~Pn306

Counter

GN1 , CN2
Input Contacts

Pn313
Smooth
AC/ Deceleration

Position
Command
Direction

Position
error set
to 0

Position Rate Gain 1

Pn310

Pn314
Motor Position
Feed Back

Pn311
Gain-Switch Method

Cn 015 ~Cn024
Input Contact
G- SEL
PCNT

Pulse clear mode

Pn315
Input contact CLR

5-31

Speed for ward

smooth filter
Cn033

Position Rate Gain 2

Speed control
loop

5-4-1 External Pulse Command

Four types of external position pulse command signals can be interfaced,
These can be selected from the list below.
Position pulse signal logic can be selected Positive or negative as required.
Parameter
Signal

Pn301.0

Pn301.1

Name

Setting

Position pulse
command selection

Position pulse
command logic
selection

Control
Mode

Description

(Pulse)+(Sign)

(CCW)and (CW) pulse

AB-Phase Pulsex2

AB-Phase Pulsex4

Positive Logic

Negative Logic

Pe

Pe

New setting will become effective after re-cycling the power.

Position pulse
command types

Positive Logic
CCW Command

Negative Logic

CW Command

(Pulse)+
(Sign)

(CCW)/
(CW) Pulse

AB-Phase Pulse

5-32

CCW Command

CW Command

Two types of pulse command can be connected, (Open collector) and (Line driver).
Please refer to section 2-2-1 for the pulse wiring method.
Pulse command timing should be in accordance with the time sequence standard below.
Pulse Command
Types

Time Sequence Diagram of Pulse Command

(Pulse)+
(Sign)

t3

t1

Time Standard
Line Driver:
t1, t2 0.1s
t3 3s
1.0s
(/T) 50%
OpenCollector:
t1, t2 0.2s
t3 3s
2.0s
(/T) 50%
LineDrive:
t1, t2 0.1s
t3 3s
1.0s
(/T) 50%
OpenCollector:
t1, t2 0.2s
t3 3s
2.0s
(/T) 50%
LineDrive:
t1, t2 0.1s
1.0s
(/T) 50%

t3

Pulse
t

t2

t2

Sign

t1

Pulse

(CCW)/
(CW) Pulse

t2

Sign
t3

t1

Pulse
t2

AB-Phase Pulse

OpenCollector:
t1, t2 0.2s
2.0s
(/T) 50%

Sign
t

Position command can be disabled ( Inhibited) by extrernal input contact INH.

Input Contact
INH

Description

Position Pulse command enabled

Position Pulse command disabled

Control
Mode
Pe

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check section 5-6-1 to set the required high /Low signal levels ( PNP/NPN) selection.

5-33

5-4-2 Internal Position Command

In internal position command mode, 16 preset position commands can be set by parameters
(Pn317~Pn364), and can be activated by use of input contacts POS1 ~ POS4.
Preset positions are programmable and can be selected according to the table below:
Position
Command

POS4

POS3

POS2

POS1

P1

P2

P3

P4

P5

P6

P7

P8

P9

P10

P11

P12

P13

P14

P15

P16

Position Command Parameter

Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number
Rotation Number
Pulse Number

5-34

Pn317
Pn318
Pn320
Pn321
Pn323
Pn324
Pn326
Pn327
Pn329
Pn330
Pn332
Pn333
Pn335
Pn336
Pn338
Pn339
Pn341
Pn342
Pn344
Pn345
Pn347
Pn348
Pn350
Pn351
Pn353
Pn354
Pn356
Pn357
Pn359
Pn360
Pn362
Pn363

Position
Speed
Parameter
Pn319
Pn322
Pn325
Pn328
Pn331
Pn334
Pn337
Pn340
Pn343
Pn346
Pn349
Pn352
Pn355
Pn358
Pn361
Pn364

For internal positioning mode there are two types of moves incremental move or absolute move,
selectable byparameter Pn316 as below.
Parameter
Signal

Name

Setting

Internal position
command mode
selection

Absolute mode

Pn316

Incremental mode

Description

Control
Mode
Pi

New setting will become effective after re-cycling the power.

Example below shows the difference between absolute and incremental moves.
For two pulse commands of 10 pulse position pulse command and followed with another 20 pulse,
the traveled positions will be different.

PTRG. (Position Trigger).

Once any preset position is selected by input contacts POS1~POS4 then require a trigger signal (PTRG)
from the input contact , enable PTRG to start operation.
Diagram below shows an example for 4 different absolute encoders.

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check section 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-35

PHOLD. (Position Hold)

The Position command can be inhibited (Held) at any time by input contact signal PHOLD.
Once PHOLD is initiated the motor will decelerate and stop.
As soon as the input contact PTRG is triggered again the original position command will be Completed.
Diagram below shows PHOLD function with incremental encoder.

CLR ( Clear position command).

If the CLR input is activated when a position command is in process then the motor will stop immediately
and the remaining positioning pulses will be cleared. Parameter Pn315 must be set to 1or 2 as required
( refer to section 5-4-7).
Once the PTRG input contact is activated again then a new position command will be started according to
the selection of input contacts POS1~POS4.

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check section 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-36

5-4-3 Electronic Gear

Electronic gear ratio parameter can be used to scale the command output pulse.
This would be useful in transmission applications where move distance per move command pulse
has to be scaled due to mechanical requirements.
Diagram and notes below describe the electronic gear ratio effect.

Example of a transmission device and calculations that show the required number of pulses from a
host controller to move the table by 10mm.

Screw Pitch = 5mm. (Move distance for

1revolution of screw)

Encoder pulse per

revolution(PPR)=2000

Calculations without Electronic Gear Ratio

Calculations with Electronic Gear Ratio

1.One rotation of ball screw = Table move distance of

For Calculating the number of pulses command required,

5mm.

Setting of Electronic gear ratio see next chapter.

2. If the table is required to move 10mm, then Ball

Electronic gear ratio can be set according to the required

screw needs to rotate by (10mm 5 mm/rev)= 2

move distance per move command pulse.

Revs

For example:

3. Command pulses required to cause one revolution:- 1. One Pulse command = Move distance of 1m.
= Encoder ppr ( Internal multiplication factor).

2. If the Motion Table needs to move 10mm,

= 2000 ppr x 4 = 8000 pulses.

Then the required command pulses from a Host Controller

4.So the Command pulses required to move 10mm (2

revs):-

is
= 10mm 1m / Pulse.= 10000 Pulses.

= 8000 pulses x 2 ( revs) = 16000 Pulses.

Number of command pulses for an specific move
distance can be calculated according to the formula
below:
= Number of Ball Screw Revs x (Encoder ppr x 4).

Once the move distance per pulse and the Electronic

gear ratio is known then the required number of pulse
command can be calculated.

5-37

Electronic Gear Ratio Calculation

Follow the Steps below:
1. Define the requirements of the positioning system
Establish the following:

Move distance per one revolution of load shaft.

Servo motor Encoder ppr (Pulse Per Revolution). (please refer to section 1-1-2 Servo Motor Standards).

Motor / load Shaft deceleration ratio.

2. Move distance per one move command pulse.

Define the move distance caused by the transmission system as a result of, one move command pulse from
the host controller.
Ex: When 1 Pulse Command move = 1m
If the Host Controller gives a move command of 2000 pulses, the transmission device will move by: -

2000pulse 1um/pulse = 2mm (The Electronic Gear Ratio must be set correctly).
3. Calculate the Electronic Gear Ratio
Calculate the Electronic Gear Ratio according to the formula below:Encoder ppr ( Pulse Per Revolution) x 4
Electronic Gear Ratio =
Move distance per load shaft revolution Move distance per command Pulse

If the deceleration ratio between motor and load shaft is

(m = Motor Rotating number , n= Load Shaft Rotating Value), Then the formula for Electronic Gear Ratio is:
Encoder ppr ( Pulse Per Revolution) x 4
Electronic Gear Ratio =

m
X

Move distance per load shaft revolution Move distance per command Pulse

Warning!
The calculated Electronic Gear Ratio must be according to the conditions below,
otherwise the servo drive and motor will not function correctly.

1
ElectroniceGearRatio 200
200

5-38

4.Parameter Setting for Electronic Gear Ratio

Setting gear ratio Numerator and denominator parameters:
Numerator and denominator values of the calculated electronic gear ratio must be entered in the required
parameters.
These two values have to be integer and with a value within the specified range in the table below.
Parameter
Signal
Pn302
Pn303
Pn304
Pn305
Pn306

Name

Default

Unit

Numerator of Electronic Gear Ratio 1

Numerator of Electronic Gear Ratio 2
Numerator of Electronic Gear Ratio 3
Numerator of Electronic Gear Ratio 4
Denominator of Electronic Gear Ratio

1
1
1
1
1

X
X
X
X
X

Setting
Range
1~50000
1~50000
1~50000
1~50000
1~50000

Control
Mode
Pi/Pe
Pi/Pe
Pi/Pe
Pi/Pe
Pi/Pe

New setting will become effective after re-cycling the power.

This device provides 4 selections of Numerator for Electronic Gear Ratio.
Input contacts GN1 and GN2 can be used to select the required Numerator for the Electronic Gear Ratio
According to the table below.
Input
Input Contact
Numerator of Electronic Gear Ratio
Contact GN2
GN1
0

Control
Mode

Numerator of Electronic Gear Ratio 1

Pn302
Numerator of Electronic Gear Ratio 2
Pn303
Numerator of Electronic Gear Ratio 3
Pn304
Numerator of Electronic Gear Ratio 4
Pn305

Pi/Pe

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-39

Electronic Gear Ratio setting examples

Transmission System

Ball Screw

Pulse Value of 1 Rotating for

Encoder=2000pulse/rev

Distance of 1 Rotating for Ball

Screw = 5mm

Mechanical Disc

Setting Process
1. Main positioning specifications:
a) Load Shaft(Ball Screw) pitch
move distance per revolution= 5mm
b) Motor Encoder ppr ( Pulse per revolution) =
2000pulses
2. Move distance per one pulse of move Command.
Moving Distance of 1 Pulse Command =1m
3. Calculation of the Electronic Gear Ratio:
2000 pulse / rev 4
8000
ElectronicGear Ration =
=
5mm / rev 1um / pulse 5000
4. Set the parameter of Electronic Gear Ratio:
Numerator of Electronic Gear Ratio = 8000
Denominator of Electronic Gear Ratio = 5000
1. Main positioning specifications:
a) Deceleration Ratio=1/5
b) Load Shaft(Mechanical Disc)Move Value per one
revolution=360

Deceleration Ratio-1/5

Load Shaft

Servo Motor
Pulse Value of Rotating for Encoder
= 2500pulse/rev

Motor Encoder ppr ( Pulse per revolution)= 2500 pulses

2. Move distance per one pulse of move Command.
Distance for 1Pulse Command =0.1
3. Calculation of the Electronic Gear Ratio:
Electronic Gear Ratio =

2500 pulse / rev 4 5 50000

=
360 0.1 / pulse 1 3600

4. Set the parameter of Electronic Gear Ratio:

Numerator of Electronic Gear Ratio = 50000
Denominator of Electronic Gear Ratio =3600
1. Main positioning specifications:
a) Deceleration Ratio=1/8
b) Load Shaft ( Idler) Move Value per revolution.

= 3.14 100mm = 314mm

Transmission Belt

c) Motor encoder ppr ( Pulse Per Revolution) =

8192pulse
2. Move distance per pulse of move Command.
Distance for 1Pulse Command =10m
3. Calculation the Electronic Gear Ratio:
8192 pulse / rev 4
8 262144
Electronic Gear Ratio =
=
314mm 10um / pulse 1 31400
4. Set the parameter of Electronic Gear Ratio:
Reduction of the fraction to make the Numerator and
Denominator less than 50000.
Numerator of Electronic Gear Ratio
32768
Denominator of Electronic Gear Ratio
3925

5-40

5-4-4 Smooth Acceleration

Using the One Time Smooth Acceleration/Deceleration of Position Command
It smoothes the position pulse command frequency.
Parameter
Signal

Name
External Position
command
Accel/Decel Time
Constant

Pn313

Default

Unit

Setting Range

Control Mode

msec

0~10000

Pi/Pe

New setting will become effective after re-cycling the power.

Time Constant of Smooth Acceleration/Deceleration of Position Command defined for a cycle as below:
The require time of the Position Pulse Frequency started from 0 to 63.2%.
Frequency of Position
Pulse Command (%)

100

Frequency of Position Pulse Command

63.2
50

Time (ms)

Pn313

Setting Examples:
(1) To achieve 95% of Position Pulse Command Frequency Output in 30msec:

Pn313 =

30(msec)
= 10(msec)
- ln(1 - 95%)

(2) To achieve 75% of Position Pulse Command Frequency Output in 30msec:

Pn313 =

30(msec)
= 22(msec)
- ln(1 - 75%)

Note:Above curve is a logarithmic

ln = Natural log.

5-41

S-curve time constant of the Internal Position Command

S-curve time constant generator can smoothen the command, it provides continuous speed and acceleration
which not only better the motor characteristic of acc/dec but also helps the motor to operate more smoothly in
machinery structure.S-curve time constant generator is only applicable to the mode of internal position command
input. When position command input switch to external position pulse, the speed and acceleration are already
constant, so it doesnt use the S-curve time constant generator.

Parameter
Signal

Pn370

Pn371

Name

Default Unit

S-Curve Time Constant for Internal Position command(TSL)

S-curve time constant generator can smoothen the command, it
provides continuous speed and acceleration which not only better
the motor characteristic of acc/dec but also helps the motor to
operate more smoothly in machinery structure.S-curve time
constant generator is only applicable to the mode of internal
position command input. When position command input switch to
external position pulse, the speed and acceleration are already
constant, so it doesnt use the S-curve time constant generator.
Notice
1. Setting rulePn371(TACC)Pn370(TSL)
2. When Pn370 = 0S-Curve time constant disabled.
S-Curve Time Constant for Internal Position command(TACC)
Please refer to Pn370 statament

Setting Control
range mode

x0.4ms

5000

Pi

x0.4ms

5000

Pi

We define the input time parameter are TSL and TACC. It judges the acc/dec trip by the setted time
parameter.
Figure (a) shows that when TACC > TSL, it will generate a constant acceleration region, and the time of
acceleration is TACC TSL.
Refered to figure (b), there is no constant acceleration region when TACC = TSL, and it can not be define on
TACC<TSL.

5-42

TACC = TSL

TACC > TSL

TACC < TSL

TSL
2

TSL
2

TSL
2

TACC

TACC

TSL
2

x(t)
t

(d)
vMAX
v(t)

(c)
aMAX
a(t)

jMAX

-aMAX

(b)

j(t)
-jMAX
0

TSL

TACC

(a)

T1

T1

T1

TACC

TSL

TACC

TSL

T1

TSL
+

S-Curve trip time definition

5-43

TACC

5-4-5 Definition of Direction

In position mode, user can use Pn314 (Position Command Direction Definition) to define motor rotation
direction. The setting is showed as follow:
Parameter
Signal

Name

Setting

Definition of position
command direction (from
motor load end)
CCW

Description

Control
Mode

Clockwise (CW)

CW

Pi
Pe

Pn314
1

Counter Clockwise (CCW)

New setting will become effective after re-cycling the power.

5-4-6 Gain Adjustment
The table below shows the parameters for adjusting the position loop.
Two position loop gains can be selected from input contact terminals according to table below.
For selection methods refer to section. 5-3-11.
Parameter
Signal
Pn310
Pn311
Pn312
Cn033

Name

Default

Unit

Setting Range

40
40
0
40

1/s
1/s
%
Hz

1~450
1~450
0~100
1~100

Position Loop Gain1

Position Loop Gain 2
Position Feed-Forward Gain
Speed Feed-Forward Smooth Filter

Control
Mode
Pe/Pi
Pe/Pi
Pe/Pi
Pe/Pi

Diagram below shows the position controller. Adjust a higher gain value can reduse response time.
Position Feed-Forward Gain can also be used to shorten the positioning time.
refer to section 5-5 for Position Loop Gain Adjustment methods.

Position Controllor
K pff
Position Pulse
Command

Filter

Kp

Encoder Pulse Feed Back

5-44

Kp : Position Loop Gain (1/s)

Kpff : Position Loop
Feed-Forward Gain (%)

5-4-7 Clear the Pulse Offset

In position control mode, parameter Pn315 (Pulse Error clear mode) has three modes can be select.
CLR input contact is used to clear the pulse error as required according to the list below.

Parameter

Name

Setting
0

Pn315

Pulse Error Clear

Mode

Description
When Input CLR contact, clears the pulse error
value.
When Input CLR contact to cancels the position
command, Stops the motor rotating, the pulse error
value is cleared and mechanical Home signal is
reset.
When Input CLR contact to cancels the position
command, stops the motor rotating and the pulse
error value is cleared.

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-45

Control
Mode
Pe
Pi
Pe
Pi

5-4-8 Original Home

Home routine is used to find and set a reference point for correct positioning.
To set a HOME reference position, one of input contacts ORG (external sensor input), CCWL, or CWL can be
used.
An encoder Z phase (marker pulse) can also be used as home reference and can be search by CW or CCW
direction. Following Home routine selections are available for setting parameter Pn 365.0.
Parameter

Name

Setting

On activation of
Home input
contact,
Pn365.0
It sets the
search
direction
and Home
reference.
(Setting for
home routine)

Description

Control
Mode

Once the home routine is activated, motor will search for Home
Position switch in 1st preset speed in CCW direction.
Input contacts CCWL or CWL can be used as the Home Reference
Switch.
Once Home reference switch is detected and complete, input contacts
CCWL and CWL will act as limits input contact again.
Note:
When using this function, 1 or 2 setting of Pn365.1 is not allowable.
Cn002.1 (CCWL & CWL Input terminal function) must to set as 0.
Once the home routine is activated, motor will search for Home
Position switch in 1st preset speed in CW direction.
Input contacts CCWL or CWL can be used as the Home Reference
Switch.
Once Home reference switch is detected and complete, input contacts
CCWL and CWL will act as limits input contact again.
Note:
When using this function, 1 or 2 setting of Pn365.1 is not allowable.
Cn002.1 (CCWL & CWL Input terminal function) must to set as 0.
Once the home routine is activated , motor will search for Home
Position switch in 1st preset speed in CCW direction and sets the input
contact ORG (external sensor input) as a Home reference when ORG
contact is activated.
If Pn365.1=2, it will directly find the closest Rising-Edge of ORG
to be the Home position (without a need for Home reference),then it
stops in accordance with Pn365.3 setting.
Once the home routine is activated , motor will search for Home
Position switch in 1st preset speed in CW direction and sets the input
contact ORG (external sensor input) as a Home reference when ORG
contact is activated.
If Pn365.1=2, it will directly find the closest Rising-Edge of ORG
to be the Home position (without a need for Home reference),then it
stops in accordance with Pn365.3 setting.
Once the home routine is activated , motor will search for Home
position in 1st preset speed in CCW direction and sets the Home
reference
Servo drive start to find the Home position of the nearest Z phase.
(No need for Home reference)
When using this function, set Pn365.1=2 .
After finished setting of Z Phase to the Home position, for the stop
method refer to the setting of Pn365.3.
Once the home routine is activated , motor will search for Home
position in 1st preset speed in CW direction and sets the Home
reference
Servo drive start to find the Home position of the nearest Z phase.
(No need for Home reference)
When using this function, set Pn365.1=2 .
After finished setting of Z Phase to the Home position, for the stop
method refer to the setting of Pn365.3.

5-46

Pi/Pe

Parameter

Name

Setting

Once Reference
Home switch or
Signal, is found
set search
method
for the Home
position.

Pn365.1

2
0
Pn365.2

Setting of
Home Routine
Start method

Pn365.3

Stopping mode
after finding
Home signal.

Control
Mode

Description
Once the Home Reference switch or signal is detected,
motor reverses direction in 2nd speed to find the nearest Z
Phase pulse and sets this as the Home position,
then stops in accordance with Pn365.3 setting method.
Once the Home Reference switch or signal is detected,
motor Continues in its direction in 2nd speed to find the
nearest Z Phase pulse and sets this as the Home position,
then stops in accordance with Pn365.3 setting method.
When Pn365.0=2 or 3, it finds the rising edge of ORG to be the
Home position, then stops in accordance with Pn365.3;
When Pn365.0=4 or 5, it finds Z Phase pulse to be the Home,
then stops in accordance with Pn365.3.
Homing routine is Disabled.
On power up and activation of Servo on the home routine is
started automatically.
This method is useful for applications that do not require
repeated home routines. No external home reference switch is
required.
Use SHOME input contact to start a home routine.
In position mode, SHOME can be used to start a home routine
at any moment.
After detecting the Home signal, it sets this position to be the
Home reference (Un-14 encoder feed back rotating number and
Un-15 encoder feed back pulse number are all 0), motor
decelerates and stops.
Then it reverses direction in 2nd speed to detect the Home
Position again then it decelerates and stops..
After detecting the Home signal, it sets this position to be the
Home reference (Un-14 encoder feed back rotating number and
Un-15 encoder feed back pulse number are all 0), motor
decelerates and stops.

Pi/Pe

Pi/Pe

Pi/Pe

Home Mode selection table

Pn365.0 pn 365.1 selections can be made for each application as required according to the table
below:Pn365.0
Pn365.1

0
1
2
HOME routine available

HOME routine not available.

5-47

Additional Home routine parameters

Home search speed parameters 1st (Fast) and 2nd (Slow) speeds are set according to table below:
Parameter
Signal
Pn366
Pn367

Name
1st preset high speed of
HOME
2nd preset low speed of HOME

Default

Unit

Setting Range

Control Mode

100

rpm

0~2000

Pi/Pe

50

rpm

0~500

Pi/Pe

Parameters Pn368 and Pn 369 provide Home position offset feature for applications where
the machine mechanical home position is a different position to the detected home position.
This offset can be achieved by setting the two parameters below.
Once the detected home position is found in accordance with Pn365 (Home routine mode),
then it will search by number of revolutions and pulses set in Pn368 and Pn 369 to find the
new off set Home position.
Parameter
Signal
Pn368
Pn369

Name
HOME Position Offset.
(No of Revolutions)
HOME position Bias Pulse
value (No of pulses)

Default

Unit

Setting Range

Control
Mode

rev

-30000~30000

Pi/Pe

pulse

-32767~32767

Pi/Pe

5-48

Home routine Timing Chart

During the Home routine if the SON (Servo On) is not activated or any alarm happens,
Home routine is stopped and Home Complete output contact is reset (Cleared).
Pn365.2=2
(SHOME triggers HOME)

Pn365.2=1
(After Power ON, Home function will be automatically
operated when first time Servo ON)

Turn ON
Power

Turn ON

Power

Output Contact RDY

1

Output Contact RDY

Input Contact SON

1

1
Input Contact SHOME

Input Contact SON

Process of Home

Into the Process of

Home

Process of Home

Into the Process of

Home

1
Output Contact Home

Output Contact Home

Time

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check 5-6-1 to set the required high /Low signal levels ( PNP/NPN) selection.

5-49

Time

Home Routine Speed /Position Timing Charts

Following Sections Show the Speed/Position Timing charts according to Pn 365.0 and Pn365.1 selections.
Pn365.0
Pn365.1
0
1
2

(1)

(2)

(1)
(3)
(5)

(2)
(4)
(6)

(7)

(8)

No Home routine
(1)
Pn365.0=0 or 2 (After starting HOME routine, run CCW in 1st preset high speed for HOME Reference
(CCWL, CWL or ORG).
Pn365.1=0(After finding HOME Reference, reverse direction in 2nd preset low speed to search
for the nearest Z Phase pulse to be set as the HOME position).
Pn365.2=2(Input Contact SHOME to Start Home routine).
Pn365.3=0(Reverse search for HOME position).

5-50

(2)
Pn365.0=1or 3. After starting the HOME routine, run CW in 1st preset high speed to search for HOME
Reference (CWL, CCWL or ORG).
Pn365.1=0 . After finding HOME Reference, reverse direction in 2nd preset low speed to search for the
nearest Z Phase pulse to be set as the HOME position.
Pn365.2=2 . Input Contact SHOME Starts the Home routine.
Pn365.3=0. Reverse search for HOME position.

Speed

(2nd Stage
Pn367 low speed) Pn365.1=0

Position
Pn365.3=0

Pn366 (1st Stage

high Speed)

Z-Phase Pulse of
Motor Encoder
Pn365.0=1

Input Contacts CWL, CCWL

or ORG
Pn365.0=3
Input Contact SHOME

1
Pn365.2=2

(3)
Pn365.0=2. After starting HOME routine, run CCW in 1st preset high speed to search for HOME Reference
(ORG).
Pn365.1=1. After finding HOME Reference, continues in the same direction in 2nd preset low speed to find
the nearest Z Phase to be set as the HOME position.
Pn365.2=2 Input Contact SHOME Starts the HOME routine.
Pn365.3=0 Reverse search for HOME position

5-51

(4)
Pn365.0=3(After Starting HOME routine, run CW in 1st preset high speed to search for HOME
Reference.( ORG)
Pn365.1=1. After finding HOME Reference, continues in the same direction in 2nd preset low speed to find
the nearest Z Phase to be set as the HOME position.
Pn365.2=2 Input Contact SHOME Starts the HOME routine.
Pn365.3=0 Reverse search for HOME position

Speed
Pn365.3=0
Position
Pn367 (2nd Stage low speed)
Pn365.1=1
Pn366 (1st Stage High Speed)

Z-Phase Pulse of
Motor Encoder
1

Input Contact ORG

Pn365.0=3
Input Contact SHOME

1
Pn365.2=2

5-52

(5)
Pn365.0=2. After Starting HOME routine, run CCW in 1st preset high speed to search for HOME
Reference.( ORG).
Pn365.1=2. After Finding the HOME Reference, the Rising Edge of ORG sets the HOME Position.
Pn365.2=2 Input Contact SHOME Starts the HOME routine.
Pn365.3=0 Reverse search for HOME position

Speed
Pn366 (1st stage high speed)

Pn365.3=0
Position
Pn367

(2nd

stage low speed)

Pn365.1=2
1

Input Contact ORG

Pn365.0=2
Input Contact SHOME

1
Pn365.2=2

(6)
Pn365.0=3. After Starting HOME routine, run CW in 1st preset high speed to search for HOME
Reference.( ORG).
Pn365.1=2. After Finding the HOME Reference, the Rising Edge of ORG sets the HOME Position.
Pn365.2=2 Input Contact SHOME Starts the HOME routine.
Pn365.3=0 Reverse search for HOME position
Speed
Pn367 (2nd stage low speed)
Position
Pn365.3=0

Pn366 (1st stage high speed)

Pn365.1=2
1

Input Contact ORG

Pn365.0=3
Input Contact SHOME

1
Pn365.2=2

5-53

(7)
Pn365.0=4. After Starting HOME routine, run CCW in 1st preset high speed to search for the nearest Z phase
pulse.
Pn365.1=2. After Finding the Z phase pulse, set this position as the HOME position.
Pn365.2=2 Input Contact SHOME Starts the HOME routine.
Pn365.3=0 Reverse search for HOME position

Speed
Pn366 (1st stage high speed)

Pn365.3=0
Position
Pn367

(2nd

stage low speed)

Pn365.1=2

Z-Phase Pulse of
Motor Encoder
Pn365.0=4
1

Input Contact SHOME

Pn365.2=2

(8)
Pn365.0=5. After Starting HOME routine, run CW in 1st preset high speed to search for the nearest Z phase
pulse.
Pn365.1=2. After Finding the Z phase pulse, set this position as the HOME position.
Pn365.2=2 Input Contact SHOME Starts the HOME routine.
Pn365.3=0 Reverse search for HOME position

Speed
Pn367 (2nd stage low speed)
Position
Pn365.3=0

Pn366 (1st stage high speed)

Pn365.1=2

Z-Phase Pulse of
Motor Encoder
Pn365.0=5
Input Contact SHOME

1
Pn365.2=2

5-54

5-4-9 Other Position Function

In position (Position Complete)
As long as the position error value (counts) is less than the pulse counts set in
Pn307 (Position Complete value) then INP output contact will be activated.

Parameter

Name

Default

Unit

Setting Range

Pn307

Position Complete value

10

pulse

0~50000

Control
Mode
Pi/Pe

Speed Command
Motor Speed
Speed

Pn307
Position Complete Value

Position Incorrect Value

pulse

INP Statue

Note: Input contacts status 1 (ON) and 0 (OFF)

Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

Position error alarm

When the Position error value is greater than the preset pulse value of Pn308 (Positive position error level) or
Pn309 (Negative position error level) this will generate AL-11 (Position error) signal.

Parameter
Pn308
Pn309

Name
Positive position error level
Negative position error level

Default

Unit

Setting Range

50000
50000

pulse
pulse

0~50000
0~50000

5-55

Control
Mode
Pi/Pe
Pi/Pe

5-5

Gain Adjustment
The Servo controller provides 3 control loops as diagram shown below:
Control methods are: Current Control, Speed Control and Position Control.

Host
Controllor

Speed
Controllor

Position
Controllor

Power
Circuit

Current
Controllor

SM

PG

Diagram above shows the three control loops.

Current ( Inner loop), Speed ( middle loop) and position (outer loop).
Theoretically, the bandwidth of inner control loop must be higher than the bandwidth of the outer control loop,
otherwise, the whole control system will become unstable, and cause vibration or abnormal response.
The relationship between the band width for these three control loops is as follows:
Current Loop (Inner) >Speed Loop (Middle )>Position Loop(outer).
The default current control bandwidth has already been set for optimum response, So Only speed an d
position control loop gains may be adjusted.
Table below shows the Gain adjustment parameters for the three control loops.

Parameter

Name

Default

Unit

Setting Range

Control
Mode

Sn211

Speed Loop Gain 1

40

Hz

10~450

Pe/Pi/S

Sn212

Speed Loop Integration Time

Constant 1

100

x0.2
msec

1~500

Pe/Pi/S

Sn213

Speed Loop Gain 2

40

Hz

10~450

Pe/Pi/S

Sn214

Speed Loop Integration Time

Constant 2

100

x0.2
msec

1~500

Pe/Pi/S

Pn310

Position Loop Gain 1

40

1/s

1~450

Pe/Pi

Pn311

Position Loop Gain 2

40

1/s

1~450

Pe/Pi

Pn312

Position
Gain

0~100

Pe/Pi

Cn025

Load Inertia Ratio

40

x0.1

0~1000

Pe/Pi/S

Loop

Feed-Forward

5-56

Speed Loop Gain

Speed Loop Gain has a direct effect on the response Bandwidth of Speed Control Loop.
Under the condition of no vibration or noise, when higher is the Speed Loop Gain Value is setting speed
response is becoming faster.
If Cn025 (Load Inertia Ratio) is correctly set then,
Speed Loop Bandwidth = Sn211 (Speed Loop Gain1) or Sn213 (Speed Loop Gain2).
Load Inertia Ratio Formula is as below:

Speed Loop Integration Time Constant

Integral element in Speed Control Loop eliminates the steady state error.
Under the condition of no vibration or noise, reducing the speed loop Integral Time Constant can enhance
system rigidity. If the Load Inertia Ratio is very high or the system has vibration factors, ensure that the Speed
Loop Integral Time Constant is also high enough, otherwise the mechanical system would produce
resonance easily.
Integral Time Constant for Speed Loop can be set using the formula below:

Sn212(Integral Time constant 1 of Speed Loop) 5

1
2 Sn211(Speed Loop Gain 1)

Setting Example:
Assume: Cn025 (Load Inertia Ratio) is correctly set, If target Speed Loop Bandwidth 100Hz,
set Sn211(Speed Loop Gain 1)=100(Hz) then
Sn212(Integral Time Constant 1 of Speed Loop) 5

1
= 40 (0.2msec)
2 100

5-57

Position Loop Gain

Position Loop Gain has a direct effect on the response speed of Position Loop.
Under the condition that there is no vibration or noise from servo motor, increasing the Position Loop Gain
Value can enhance the response speed and hence reduce the positioning time.

Position Loop Feed-Forward Gain

Using Position Loop Feed-Forward Gain can enhance the response speed.
If the Feed-Forward Gain value is setting too high, overshooting could occur and cause the INP (In Position)
output contact to switch ON and OFF repeatedly.
SO monitor Speed Curve and INP (In Position Signal) at the same time then increase Feed-Forward Value
slowly.
If Position Loop Gain is too high, Feed-Forward function will be insignificant.

Quick Parameters for Gain adjustment

Quick Gain adjust parameters are available for setting manually.
The related Gain Adjust parameters are listed in the Quick-Parameter leaflet for convenient reference.
Quick adjust parameters once altered are saved and become effective immediately,
without pressing the Enter-Key. The table below shows the Gain Adjust Quick-Parameters.
Name

Parameter

Default

Unit

Setting Range

Control
Mode

qn401

Speed Loop Gain 1

40

Hz

10~450

Pe/Pi/S

qn402

Integral Time Constant 1 of

Speed Loop

100

x0.2
msec

1~500

Pe/Pi/S

qn403

Speed Loop Gain 2

40

Hz

10~450

Pe/Pi/S

qn404

Integral Time Constant 2 of

Speed Loop

100

x0.2
msec

1~500

Pe/Pi/S

qn405

Position Loop Gain 1

40

1/s

1~450

Pe/Pi

qn406

Position Loop Gain 2

40

1/s

1~450

Pe/Pi

qn407

Position
Gain

0~100

Pe/Pi

Loop

Feed-Forward

Become effective immediately without pressing Enter-Key

5-58

5-5-1 Automatic Adjusting

This device provides ON-LINE Auto tuning, which can quickly and precisely measure Load Inertia
and adjust the Gain automatically. Setting is according to the table below:
Parameter

Name

Setting

Cn002.2

Description

Control
Mode

Auto tuning Disabled

Auto tuning

Pe/Pi/S
1

Enable Auto tuning

When Cn002.2 is set to 0 (Auto tuning Disabled), following Gain adjust parameters must be set.
Parameter
Signal
Cn002.2

Name
Auto tuning

Sn211

Speed Loop Gain 1

Sn212

Speed-loop Integral time constant 1

Sn213

Speed loop Gain 2

Sn214

Speed loop Integral time constant 2

Pn310

Position Loop Gain 1

Pn311

Position Loop Gain 2

Pn312

Position Loop Feed-Forward Gain

When Cn002.2 is set to 1 auto tuning is enabled and the Servo controller will adjust the Servo Gain in
accordance with Cn026 (Rigidity Setting) and the measured Load Inertia Ratio by monitor parameter Un-19
(Load Inertia Ratio), when the Load Inertia Ratio is becomes stable,
Then set 0 in Cn002.2 to cancel Auto tuning. At this moment, servo controller will record the measured Load
Inertia Ratio into Cn025 (Load Inertia Ratio).
If servo drive is used in a applications where there is no significant load variations, then monitor Un-19 (Load
Inertia Ratio) if this is stable then it is recommended that Auto tuning is not used.

5-59

Apply conditions of Auto tuning

The Servo drive provides Auto tuning and uses an advanced control technique ON-LINE to measure the
Load Inertia Ratio to control the system to achieve default speed or Position Response Bandwidth.
System must comply with the conditions below, so that the Auto tuning can operate normally.
(1) The timing from stop to 2000rpm needs be less than 1 second.
(2) Motor speed is larger than 200rpm.
(3) Load Inertia needs be 100 times less than the inertia of the motor.
(4) External force or the variation of inertia ratio can not be excessive.

Rigidity Setting
When Auto tuning is used, set the Rigidity Level depending on the various Gain settings for applications
such as those listed below:
Rigidity
Setting
Cn026

Position Loop
Gain
Pn310 [1/s]

Speed Loop
Gain
Sn211 [Hz]

Speed-loop Integral
time constant 1
Sn212 [x0.2msec]

Mechanical
Rigidity

15

15

300

Low

20

20

225

30

30

150

40

40

100

60

60

75

85

85

50

120

120

40

160

160

30

200

200

25

250

250

20

5-60

Middle

High

Application
Machines driven by timing
Belt, Chain or Gear: Large
Moving Table, Conveyor Belt.
The machines driven by
Ballscrew through
decelerator: Ordinary
machines, Mechanics arms,
robot arms, conveyor.
The machines driven by
Ballscrew: High precision
Machines, Metal engraving
Machine, Insertion Machine
and IC inspection Machine.

Process for Auto tuning

The Diagram below show the process for Auto tuning.

Note: After Auto tuning is complete Set 0 in Cn002.2, otherwise it will not record the present
measured Load Inertia Ratio.
If the power is cut off during Auto tuning then when the power is established, Servo controller will use
the previously recorded setting of Load Inertia Ratio which is stored in parameter Cn025.

5-61

5-5-2 Manual Adjustting

Manual Gain adjustment is made available for applications when
auto tune is not providing a good and stable system response, Or a system where there is no
significant load variations and the auto tune is not used.

Manual Gain Adjustment in Speed control Mode

Step 1: Set Rigidity level in parameter Cn 26 (See section 5-5-1 for the selection table) and Cn25.
Step 2: If the Servo system includes a host controller which is used for positioning control, then its position
loop Gain should be set lower, relative to the servo drive Gain.
Step 3: Adjusting Speed Loop Gain 1 (Sn211):
a) Increase Sn212 (Integral Time Constant 1of Speed Loop). Set a higher value than default or the set
value when auto tune was unsuccessful.
b) Increase the Speed Loop Gain (Sn211) until there is no vibration or noise.
c) Then decrease the Speed Loop Gain (Sn211) slowly and increase Position Loop Gain of Host
Controller until there is no vibration or noise.
Step 4: Adjusting Speed Loop Integral Time Constant 1 (Sn212):
Set the Integral Time Constant of Speed Loop for minimum time setting that without causing mechanical
vibration.
Step 5: Finally, Slowly adjust the Speed Loop Gain, Position Loop Gain of Host Controller and Integral Time
Constant of Speed Loop until the servo system provides the best response.

Manual Gain Adjustment in Position Control mode

Step 1: Set Rigidity level in parameter Cn 26 (See section 5-5-1 for the selection table) for the correct Load
Inertia Ratio.
Step 2: Decrease Position Loop Gain 1 (Pn 310).
Set a lower value than default or the set value when auto tune was unsuccessful.
Set a relatively higher value in Sn212 (Integral Time Constant 1 of Speed Loop).
Step 3: Adjust Speed Loop Gain 1(Sn211).
Increase the Speed Loop Gain until there is no vibration or noise.
Step 4: Adjusting Position Loop Gain 1 (Pn310).
Slowly decrease the Speed Loop Gain again, then increase the Position Loop Gain until there is no
vibration or noise.
Step 5: Adjusting Speed Loop Integral Time Constant 1 (Sn212).
Set the Integral Time Constant of Speed Loop for a minimum time without causing mechanical vibration.
Step 6: Finally, slowly adjusting the Speed Loop Gain, Position Loop Gain and the Integral Time Constant of
Speed Loop until the servo system provides the best response.

5-62

5-5-3 Improving Resonance

The Servo drive provides the function of Gain Switching and Position Loop Feed-Forward Gain
to improve system response.
Note: Both of these features must be used correctly to improve system response, otherwise
the response will become worse. Refer to the description below:

Gain Switch
Following Gain Switching features are provided:a) Speed Loop Gain PI/P Switching
b) 2-stage Gain Switching.
Purposes list:
(1) To restrict overshoot during acceleration/deceleration in speed control.
(2) Reducing the in position oscillations and providing shorter settling time in position control.
(3) Decrease the noise caused when using Servo Lock.
For further details refer to section 5-3-11.

Position Loop Feed-Forward Gain

Position Loop Feed-Forward Gain can be used to reduce the error result from position control and improve
the response speed.
Position loop Feed forward gain and position loop gain should be matched with. If adjusting to higher position
loop gain, the feed fordward gain can be ignored. Oppositly, if the loop gain value is setting for a relatively low
level, adjust position loop feed forward gain will improve system response time obviously.
The adjustment steps are as follows:
Step 1: Refer to the procedures in sections 5-5-1~5-5-2 to adjust Speed and Position Gain.
Step 2: Increase Pn312(Position Feed-Forward Gain) slowly, and observe the INP ( Output Signal of In
Position) at the same time and INP output should be activated faster.
Note: The Position Loop Feed-Forward Gain can not be set too high, otherwise it will cause speed
overshooting and INP (In Position output signal) will be switching On/Off repeatedly.

5-63

5-6 Other Functions

5-6-1 Programmable I/O Functions
Digital Inputs.
There are 13 DI (Digital Inputs) contacts and 4 DO (Digital Outputs) contacts which
are programmable as listed below:Parameter

Name

Setting

Description
Signal

Hn501.0
Hn501.1

DI-1
Digital Input 1
programmable
Functions

01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F

SON
ALRS
PCNT
CCWL
CWL
TLMT
CLR
LOK
EMC
SPD1
SPD2
MDC
INH
SPDINV
G-SEL

10

GN1

11

GN2

12
13
14

PTRG
PHOLD
SHOME

15

ORG

16
17
18
19
1A
1B
1C

POS1
POS2
POS3
POS4
TRQINV
RS1
RS2

Control
Mode

Contactor Function
Servo On
Alarm Reset
PI/P Switching
CCW Limit
CW Limit
External Torque Limit
Clear Pulse Error Value
Servo Lock
Emergency Stop
Speed 1
Speed 2
Control Mode Switch
Position Command Inhibit
Speed Inverse
Gain Select
Electronic Gear Ratio
Numerator 1
Electronic Gear Ratio
Numerator 2
Position Trigger
Position Hold
Start Home
Home Position Reference
(Origin)
Internal Position select 1
Internal Position select 2
Internal Position select 3
Internal Position select 4
Torque Inverse
Torque CW Selecting
Torque CCW Selecting

ALL

New setting will become effective after re-cycling the power.

Parameter
Signal
Hn501.2

Name
DI-1
Logic State
NO/NC Selection

Setting
0
1

Description
Input contact state. NO (Normally Open).
Connecting (IG24) to inputs, enables the
selected function.
Input contact state. NC (Normally Closed).
Disconnecting (IG24) from inputs, enables
the selected function.

Control
Mode

ALL

New setting will become effective after re-cycling the power.

Digital Inputs 2 to 13 (Hn 502 to Hn 513). Are programmable and the logic state NO/NC can also be
selected same as that shown for digital input 1. See Hn501.

5-64

Parameter

Name

Description

Control
Mode

Hn502
Hn503
Hn504
Hn505
Hn506
Hn507
Hn508
Hn509
Hn510
Hn511
Hn512
Hn513

DI-2 Programmable
DI-3 Programmable
DI-4 Programmable
DI-5 Programmable
DI-6 Programmable
DI-7 Programmable
DI-8 Programmable
DI-9 Programmable
DI-10 Programmable
DI-11 Programmable
DI-12 Programmable
DI-13 Programmable

Refer to Hn501 for programmable options.

ALL

Warning! If any of programmable Inputs of DI-1 ~ DI-13 are set for the same type of function
then the logic state selection ( NO or NC selection) for these inputs must be the same type.
Otherwise an Alarm will be displayed. AL-07 (Multi-function contact setting error).

5-65

Digital Outputs.
There are 4 programmable Digital Outputs according to the table below:
Parameter

Name

Setting

Description
Code

Hn514.0
Hn514.1

DO-1 Logic
state

Hn514.2
DO-1

01
02
03
04
05
06
07

RDY
ALM
ZS
BI
INS
INP
HOME

08

INT

Control
Mode

Contactor functions
Servo Ready
Alarm
Zero Speed
Brake Signal
In Speed
In Position
HOME

ALL

In Torque

Close, when the output is activated.

Open, when the output is activated..

ALL

Parameter

Name

Description

Control
Mode

Hn515
Hn516
Hn517

DO-2 Programmable
DO-3 Programmable
DO-4 Programmable

Refer to Hn514 for programmable options.

ALL

New setting will become effective after re-cycling the power.

Warning!
When programmable DO-1 ~ DO-4 are set for the same type of function alarm will be displayed.
AL-07 (Multi-function contact setting error).

5-66

5-6-2 Switch for the Control Mode

Set one of the programmable input terminals to MDC (Control mode) selection.
The input then will select the preset control mode, which is set by Parameter Cn001.
Selections are listed below:
Parameter

Cn001

Name

Setting

Control Mode
Selection

Description
MDC Input off

MDC Input On

Position Control
(External Pulse Command)

Speed Control

Speed Control

Torque Control

5
7
8

Position Control
(External Pulse Command)
Position Control
(Internal Pulse Command)
Position Control
(Internal Pulse Command)

Control
Mode

ALL
Torque Control
Speed Control
Torque Control

New setting will become effective after re-cycling the power.

Please check 5-6-1 to setting the input contact required high /Low signal levels (PNP/NPN
selection).

5-6-3 Auxiliary Functions

Function of Input Contacts SON, CCWL and CWL can be set according to the list below:Parameter

Name

Cn002.0

SON
(Servo ON )

Cn002.1

CCWL and CWL

(Counter Clockwise
&
Clockwise Limits)

Setting
0
1
0

Description
Use input contact SON to switch Servo On
Servo on with Power on.
SON input contact not required.
CCWL and CWL(external limits) are effective.
CCW and CW rotation is inhibited by
CCWL&CWL.
CCWL and CWL(external limits) are
ineffective.
CCW&CW rotation is not limited by
CCWL&CWL.

New setting will become effective after re-cycling the power.

5-67

Control Mode
ALL

ALL

5-6-4 Brake Mode

Brake function for servo motor and the external mechanical brake if it is used can be set according to the table
below. Set the brake mode as required for Servo off, Emergency Stop and CCW/CW rotation inhibit functions.
Parameter

Cn008

Name

Brake
Modes

Setting

Control
Mode

Description
Dynamic Brake

Mechanical Brake

Disable

Disable

Disable

Enable

Enable

Disable

Enable

Enable

4
5

Disable(Under
100rpm)
Disable(Under
100rpm)

ALL

Disable
Enable

Note!
When the CCW/CW Drive Inhibit occur, the Cn009 has the higher priority than Cn008.
Example:
If Cn008 is set to 0 or 1 which means (no Dynamic Brake).
BUT Cn009= 1 (with Dynamic Brake), then the dynamic brake will be effective( enabled).

5-6-5 Timing Diagram of Mechanical Brake

In applications with vertical loading, if the power is turned off, to prevent the load from falling
due to gravity, a servo motor with electro-mechanical brake can be used.
This servo drive provides a brake output (BI) which can be used for controlling the external brake.
Timing of brake output signal can be set by parameter Cn003 (Output Time for electro-mechanical Brake).

Typical Circuit Diagram

CN2

5-68

Timing for Brake output signal

Set the required time for the operation of brake output signal (BI) according to the following.
BI output can be used to control the function of an external electro-mechanical brake.
Parameter
Cn003

Name
Output time setting for
Mechanical Brake
Signal

Default

Default

Setting Range

Control Mode

msec

-2000~2000

ALL

Note!
To use brake output signal set Cn008 (Brake mode) to selections 1 or 3 as required.
When the servo system has vertical loading, please set Cn003 to a Positive Number.
For definition of a time value with a positive or a negative sign refer to the following
notes and timing diagrams.
(1) Cn003 set to a time value with a Positive sign.
AS soon as the input contact SON is switched on, Servo on is activated at the same time,
then after a time delay set by parameter Cn003,Output Contact BI is switched on. (Signal to release the
brake).
When SON input contact is switched off, BI output contact is also switched off (Signal to operate the
brake).
Then after a time delay set by parameter Cn003, Servo ON is de-activated.
(2) Cn003 set to a time value with a Negative sign.
AS soon as the input contact SON is switched on, Output Contact BI is switched on at the same time.
(Signal to release the brake). then after a time delay set by parameter Cn003, Servo on is activated.
When SON input contact is switched off, Servo ON is de-activated at the same time.
then after a time delay set by parameter Cn003, Output Contact BI is switched off. (Signal to operate the
brake).

1
1

Note: Input contacts status of above time sequence diagram 1 (ON) and 0 (OFF).
Please check 5-6-1 to set the required high /Low signal levels (PNP/NPN) selection.

5-69

5-6-6 CW/CCW Drive Inhibit Function

Stopping method of the servo motor as a result of CW/CCW Inhibit function
can be selected according to the list below:
Parameter

Name

Setting
0

Cn009

CW/CCW drive
inhibit

Description
When torque limit reached the setting value of
(Cn010,Cn011), servo motor deceleration to
stop in the zero clamp status.
Deceleration by using dynamic brake to stop
then hold in dynamic brake status. Cn009 setting
has priority over Cn008 setting, it require
re-cycling power to take effect after setting
changed.

Control
Mode

ALL

Once max torque limit ( 300% ) is detected then

deceleration to stop with zero clamp.

New setting will become effective after re-cycling the power.

Note!
When the Drive Inhibit occurs in CCW/CW, the Cn009 has the higher priority than Cn008.
Example:
If Cn008 is set to 0 or 1 which means (without Dynamic Brake).
BUT Cn009= 1 (with Dynamic Brake), then the dynamic brake will be effective( enabled).

CW/CCW
Drive Inhibit

Deceleration Mode

After Stopping

Cn009=0

Torque Limit (Cn010,

Cn011) Decelerating

Cn009=1

Dynamic BK
Decelerating

Cn009=2

300% of Torque Limit

Decelerating

Zero Clamp

Dynamic BK The Servo Power

needs Restart

5-70

Zero Clamp

5-6-7 Selecting for External Regeneration Resistor

In applications where a high inertia load is stopped rapidly, motor will generate an energy, which is regenerate
power back to the servo drive ( Regeneration energy)
(1) Short deceleration time with heavy loads.
(2) In vertical load applications.
(3) High inertia rotary load applied to the motor shaft.
Part of the regeneration power will be absorbed by the drive main smoothing capacitors
If there is too much regeneration power which can not be totally absorbed by the capacitor then regeneration
resistors can be used to absorb the excess power.
Built-in Regeneration Resistor specification is as below table.

Drive Model
JSDA-15
JSDA-20
JSDA-30
JSDA-50
JSDA-75
JSDA-100
JSDA-150
JSDA-200
JSDA-300

Resistance()

Power(W)

50
50
25
20
12.5
12.5
8

60
60
60
150
150
150
200

The Regeneration
Power(W) absorbed by
the built in Resistor
(Average Power)
24
24
24
60
60
60
80

Built-in Regeneration
Resistor Specifications

Minimum allowed
Resistance Value
()
50
40
25
15
10
10
6
3
3

Built-in Regeneration Resistor

The Regeneration Resistor which is built-in this device can absorb the Regeneration Power from
acceleration and deceleration running or Vertical Loading.
But for applications that the large load inertia causes the motor shaft to rotate, an external regeneration
Resistor must be installed to protect the servo drive otherwise the servo drive can not function correctly.
Select the resistor according to the specified values and if installing regeneration resistors in a parallel way to
have more power absorb capacibility.
Ensure that the total resistance value does not smaller than the minimum resistance listed in the
table above.

5-71

Setting for the Power of External Regeneration Resistor

When using external regeneration resistor, the power value (Watts) must be set in parameter Cn012.
Parameter

Name

Default

Unit

Setting Range

Control Mode

Cn012

Watts setting for

External Regeneration
Resistor

60 ~150

0~10000

ALL

Wiring for External Regeneration Resistor

When external Regeneration Resistor is used, must remove the link between PC and P1 on TB1 Terminal.
Then the resistor should be installed between terminals P and PC.
For safety, use of resistors with thermal protection is recommended.
The thermal switch contact can then be interlocked to disable drive or remove power if necessary.
Refer to connection diagram below:

When installing Regeneration Resistors care must be taken as the resistor absorbs the regeneration power,
and it is possible to generate the high temperatures above 100C.
Provide the necessary cooling and use appropriate high temperature wires and ensure there has enough
space between regeneration resistor and other materials.

5-72

Assess for an external resistor and calculate for the power consumption:
Use the table below to determine, if an external regeneration Resistor is necessary.
The table below shows the permitted number of no load operation cycles per minute for various servo motors
in regeneration condition.
Defination of No load operation cycles:
The servo motor, accerlate from 0 speed to rated speed and deceleration from the rated speed to 0 speed.
(No load)
The regeneration energy capacity (in Joules) which can be absorbed by the built-in resistor during no load
acceleration/deceleration period, refer to the table list below.

Drive Model

Motor Model

Permitted number of
no load operation cycles/min

JSDA-15

JSMA-LC03
JSMA-SC02

433
1775

JSMA-SC04

1004

JSMA-LC08

118

JSMA-SC04

1004

JSMA-SC08

321

JSMA-MA05

411

JSMA-MH05

186

JSMA-SC08

321

JSMA-MA10

213

JSMA-MB10

102

JSMA-MH10

95

JSMA-MA15

145

JSMA-MB15

73

JSMA-MC15

45

JSMA-MA15

484

JSMA-MB15

245

JSMA-MC15

152

JSMA-MB20

178

JSMA-MB30

121

JSMA-MC30

79

JSDA-20

JSDA-30

JSDA-50

JSDA-75

5-73

Main Capacitor
energy absorption capacity
in Joules. E C (J).

13

13

18

Calculation for the allowable operation cycles per minute by motor speed and inertia.
The formula below should be used to to calculate the permitted number of cycles/min
in regenerative mode in accordance with the actual loading and the running speed of the motor.

Allowable operation cycle/min. =

No load operation cycles

(1 + )

Rated Speed
MaxRunningSpeed

)2

= Load Inertia / Motor Inertia

If the required number of cycles /min is higher than the calculated value then an external
regeneration resistor must be installed.

Calculation of the external regeneration resistor power (Watts).

Calculate the resistor watts according to the information and formulas below:
(Energy consumed by the motor internally is ignored).
Speed

Running
Speed

Time(s)

tD

Torque

TL
Time(s)

Cycle

Step

Item

Calculate the working Energy of

the servo system.

Formula

2
E M = J T rm
/ 182

Description

E M : Working Energy of Servo system (J)

J T : Inertia applied to the motor shaft
( kg m )
2

rm : Motor running Speed(rpm)

2

Calculate the Energy

consumption by the load during
deceleration.

E L = ( / 60)rmTL t D

Calculate the Energy absorbed by

internal main capacitor.

EC Check the diagram above

E L : The Energy during deceleration (J)

TL : Loading Torque(Nm)
t D : The Time from deceleration to stopping(s)
EC : The Energy absorbed by the main

Calculate the Energy which

regeneration resistor consumes

E R = E M - ( E L + EC )

E R : The Energy which Regeneration Resistor

Calculate the Power for

regeneration resistor

PR = ( E R /T ) / 0.4

capacitor (J)
consumes (J)

PR : Regeneration Resistor Power(W)

T : Operating cycle for servo system(s)

Note 1 : 0.4 in the formula for PR corresponds to 40% regeneration duty cycle.
Note 2: If the E L can not be calculated, then let E L = 0 , then calculate ER .
In applications with regenerative loads, which cause reverse torque, a large amount of energy will flow back to
the driver.

5-74

In such applications, calculate ER and hence regeneration resistor power according to the formula below.
Item

Formula

Description for Symbols

EG : Working Energy during the regenerative

Calculate the working Energy
during the continuous
regenerative period.

EG = ( / 60)rm ,G TG t G

period. (J)
rm ,G : Motor running speed during the
regenerative period . (rpm)
TG : Loading Torque during the regenerative
period (Nm)
t G : Regenerative Time. (s)

The formula for step 4 in the previous table will be: E R = E M - ( E L + EC ) + E G

5-6-8 Fan Setting

Availabel models that equipped with the fan ( JSDA-50 & JSDA-75 ).
Parameter

Cn031

Name

Setting

Cooling fan running

mode

Control
Mode

Description

Auto-run by internal temperature sensor.

Run when Servo ON

Always Running.

Disabled.

ALL

5-6-9 Analog Monitor

There are two analog output signals which can be used to monitor running Speed, Torque, Current and
Position as follows:

Parameters

Name & Function

Default

Unit

Setting
Range

Control
Mode

ALL

Analog monitor output selection (MON1)

Setting

Cn006.0

Cn006.1

Explanation

Speed feedback

Torque control

Speed control

3
Pulse command input
4
Position deviation value
5
Electrical angle
6
Main circuit (Vdc Bus) voltage
7
Speed feedback (+10V/1.5 times of the rated speed)
8
Torque control (+10V/3.5 times of the rated torque)
9
Speed control (+10V/1.5 times of the rated speed)
A
Torque feedback (10V/3.5 times of the rated torque)
Analog monitor output selection MON2
Refer to Cn006.0 for setting this parameter

5-75

Circuit diagram for analog monitor shows below:

Analog monitor output zero offset can be adjusted by parameters Cn027&Cn028 as below.
Parameter
Cn027
Cn028

Name

Default

Unit

Setting Range

Control Mode

x40mV

-250~250

ALL

x40mV

-250~250

ALL

Analog Monitor 1
Offset adjustment
Analog Monitor 2
Offset adjustment

Analog Monitor
Output Voltage (V)
Adjusting Value for
Bias Voltage

Time

5-6-10 Factory setting parameter

This parameter can reset all parameter settings to default value (factory reset).
Parameter
Signal

Name

Cn029

Reset parameters

Setting

Description

Disabled

All parameters are reset to default values.

New setting will become effective after re-cycling the power.

5-76

Control
Mode
ALL

Chapter 6 Parameter
6-1 Explanation of Parameter groups.
There are 9 groups of parameters as listed below.
Symbol

Description

Un-xx

Status Display Parameters.

dn-xx

Diagnostics Parameters.

AL-xx

Alarm Parameters

Cn-xx

System Parameters

Tn1xx

Torque Control Parameters

Sn2xx

Speed Control Parameters

Pn3xx

Position Control Parameters

qn4xx

Quick Set-up Parameters

Hn5xx

Multi-function I/O parameters

Control Mode Code

Signal
ALL

Control Mode
All Control Mode

Pi

Position Control Mode(Internal Positional Command )

Pe

Position Control Mode(External Pulse Command)

Speed Control Mode

Torque Control Mode

Definition of Symbols.
Symbol

Explanation
Parameter becomes effective after recycling the power.
Parameter is Effective without pressing the Enter key.

6-1

6-2 Parameter Display Table

System Parameters
Parameter

Cn001

Cn002.0

Cn002.1

Cn002.2

Cn002.3

Name & Function

Default Unit

Control Mode selection

Setting
Explanation
0
Torque Control
1
Speed Control
External Position Control (external pulse
2
Command)
3
External Position/Speed Control Switching
4
Speed/Torque Control Switching
5
External Position/Torque Control Switching
Internal Position Control (internal position
6
Command)
7
Internal Position/Speed mode switching
8
Internal Position/Torque mode switching
SON (Servo On) Input contact function
Setting
Explanation
0
Input Contact, Enables SON (Servo On).
Input Contact has no function.
1
(SON is enabled when Power on).
CCWL & CWL Input contact function.
Setting
Explanation
CCWL and CWL input contacts are able to
0
control the drive inhibit of CCW and CW.
CCWL & CWL input contacts are not able to
1
control CCW and CW drive inhibit. CCW and
CW drive inhibit is disable.
Auto Tuning
Setting
Explanation
0
Continuously Auto Tuning is Disable
1
Continuously Auto Tuning is Enabled.
EMC reset mode selection
Setting
Explanation
Reset EMC signal is only available in Servo
Off condition (SON contact is open) and
0
reset AL-09 by ALRS signal.
P.S.) It is NOT allow to reset when SON is
applied.
When EMC status is released, AL-09 can be
reset on both Servo ON and Servo OFF
conditions.
1

Attention!
Ensure that the speed command are
removed before the alarm is reset to avoid
motor unexpected start.

6-2

Setting
Range

Control
Chapter
Mode

ALL

5-1
5-6-2

ALL

5-6-3

5-5-1

Pi
Pe
S

ALL

Parameter

Name & Function

Setting Control
Chapter
Mode

Default Unit Range

Output time setting for Mechanical Brake Signal

Brake Signal Timing Sequence

Cn003

msec

-2000

2000

ALL

5-6-5

S
T

5-2-4
5-3-7

Implementation a pin for dynamic brake signal(BI) as a

output signal before to perform this function. Refer to
sequence diagram above.
Note: Signal logic level status: 1 = ON.
0 = OFF.
Refer to section5-6-1 for setting contact the high & Low
logic levels.
Motor rotate direction.(Inspect from the load side)
CW

CCW

When Torque or Speed Command value is Positive, the

setting of Motor retation direction are:
Cn004

Setting
0

Explanation
Torque Control
Counter
ClockWise(CCW)

Speed Control
Counter
ClockWise (CCW)
Counter
ClockWise (CCW)

ClockWise (CW)

Counter
ClockWise (CCW)

ClockWise(CW)

ClockWise (CW)

ClockWise (CW)

6-3

Parameter

Name & Function

Default

Unit

Encoder pulse output scale.

For default set to the rated encoder number of pulses
per revolution, such as 2500ppr.
Encoder
Cn005 Encoder ppr can be scaled by setting a ppr in the range pulse per pulse
of 1 to the rated ppr of the encoder for scaling purpose. rotation
PPR = Pulse per revolution.
Ex:encorder rated precision is 2000 ppr, If you
setting Cn005 =1000, the output is 1000ppr.
Analog monitor output selection MON1
Setting
Explanation
Speed feedback
0
(10V/1.5 times of the rated speed)
Torque control (10V/3.5 times of the rated
1
torque)
Speed control (10V/1.5 times of the rated
2
speed)
3
Pulse command input
Cn006.0
4
Position deviation value
2
5
Electrical angle
X
6
Main circuit (Vdc Bus) voltage
Speed feedback detection
7
(+10V/1.5 times of the rated speed)
Torque command
8
(+10V/3.5 times of the rated torque)
Speed command
9
(+10V/1.5 times of the rated speed)
Torque feedback detection
A
(10V/3.5 times of the rated torque)
Cn006.1 Analog monitor output selection MON2
0
Refer to Cn006.0 for setting this parameter

Cn007

Cn008

Speed reached preset.

Speed preset level for ClockWise or Counter
Rated
ClockWise rotation.
rpm 1/3
When the speed is greater then preset level in Cn007
the Speed reached output signal INS will be activated..
Brake Mode
Selectable Brake modes for Servo off, EMC and
CCW/CW drive inhibit.
Setting
Explanation
Dynamic brakes
Mechanical brakes
0
No
No
2
1
No
Yes
2
Yes
No
3
Yes
Yes
4
No (Under 100rpm)
No
5
No (Under 100rpm)
Yes

6-4

Setting
Range
1

Control
Chapter
Mode

ALL

5-3-5

ALL

5-6-9

rpm

4500

S
T

5-3-12

ALL

5-6-4

Encoder
pulse per
rotation

Parameter

Name & Function

CW/CCW drive inhibit mode

Setting
Explanation
When torque limit reached the setting value of
0
(Cn010,Cn011), servo motor deceleration to
stop in the zero clamp condition.
Deceleration by using dynamic brake to stop
Cn009
then hold in dynamic brake status. Cn009
1
setting has priority over Cn008 setting, it
require re-cycling power to take effect after
setting changed.
Once max torque limit ( 300% ) is detected
2
then deceleration to stop, zero clamp is
applied when stop.
CCW Torque command Limit.
Cn010 Ex: For a torque limit in CCW direction which is twice
the rated torque , set Cn10=200.
CW Torque command Limit.
Cn011 Ex: For a torque limit in CW direction which is twice the
rated torque , set Cn11=-200.
Power setting for External Regeneration Resistor
Refer to section 5-6-7 to choose external Regen
resister and set its power specification in Watts of
Cn012
Cn012.
P.S.)This default value will change depend on servo
model.
Frequency of resonance Filter ( Notch Filter).
Cn013 Enter the vibration frequency in Cn013, to eliminate
system mechanical vibration.
Band Width of the Resonance Filter.
Adjusting the band width of the frequency, lower the
Cn014
band width value in Cn014, restrain frequency Band
width will be wider.
PI/P control switch mode.
Setting
Explanation
Switch from PI to P if the torque command is
0
larger than Cn016.
Switch from PI to P if the speed command is
1
larger than Cn017.
Cn015.0
Switch from PI to P if the acceleration rate is
2
larger than Cn018.
Switch from PI to P if the position error is
3
larger than Cn019.
Switch from PI to P be the input contact PCNT.
4
Set one of the multi function terminals to option
03.
Automatic gain 1& 2 switch
Explanation
Setting
Switch from gain 1 to 2 if torque command is
0
greater than Cn021.
Switch from gain 1 to 2 if speed command is
1
greater than Cn022.
Cn015.1
Switch from gain 1 to 2 if acceleration
2
command is greater than Cn023.
Switch from gain 1 to 2 if position error value
3
is greater than Cn024.
Switch from gain 1 to 2 by input contact
4
G-SEL. Set one of the multi function terminals
to option 15.
6-5

Default

Unit

Setting
Range

300
250
200
-300
-250
-200

300
-300

Control Chapter
Mode

ALL

5-6-6

ALL

5-2-5
5-3-10

ALL

5-2-5
5-3-10

60
150
200

10000

ALL

5-6-7

Hz

1000

Pi
Pe
S

5-3-9

100

Pi
Pe
S

5-3-9

Pi
Pe
S

5-3-11

Parameter

Name & Function

Default Unit

Cn016

PI/P control mode switch by Torque Command

Set the Cn015.0=0 first.
If Torque Command is less than Cn016 PI control is
selected.
If Torque Command is greater than Cn016 P control is
selected.

Setting Control
Chapter
Range Mode

200

399

Pi
Pe
S

5-3-11

rpm

4500

Pi
Pe
S

5-3-11

rps/s

18750

Pi
Pe
S

5-3-11

pulse

50000

Pi
Pe
S

5-3-11

x02
msec

10000

Pi
Pe
S

5-3-11

200

399

Pi
Pe
S

5-3-11

rpm

4500

Pi
Pe
S

5-3-11

PI/P control mode switch by Speed Command

Cn017

Set the Cn015.0=1 first.

If Speed Command is less than Cn017 PI control is
selected.
If Speed Command is greater than Cn017 P control is
selected.
PI/P control mode switch by accelerate Command

Cn018

Set the Cn015.0=2 first.

If Acceleration is less than Cn018 PI control is
selected.
If Acceleration is greater than Cn018 P control is
selected.
PI/P control mode switch by position error number

Cn019

Set the Cn015.0=3 first.

If Position error value is less than Cn019 PI control is
selected.
If Position error value is greater than Cn019 P control is
selected.
Automatic gain 1& 2 switch delay time.

Cn020

Cn021

Cn022

Speed loop 2 to speed loop 1, Change over delay,

when two control speed loops ( P&I gains 1 & 2) are
used.
Automatic gain 1& 2 switch condition (Torque
command)
Set Cn015.1=0 first.
When torque command is less than Cn021 , Gain 1 is
selected.
When torque command is greater than Cn021, Gain 2
is selected
When Gain 2 is active and torque command becomes
less than Cn021 setting value, system will
automatically switch back to Gain 1 switch time delay
can be set by Cn020.
Automatic gain 1& 2 switch condition (Speed
Command)
Set the Cn015.1=1 first.
When speed command is less than Cn022 Gain 1 is
selected.
When speed command is greater than Cn022 Gain 2
is selected.
When Gain 2 is active and speed command becomes
less than Cn022 setting value, system will
automatically switch back to Gain 1 the switch time
delay can be set by Cn020.

6-6

Parameter

Cn023

Cn024

Cn025

Cn026

Name & Function

Default Unit

Automatic gain 1& 2 switch condition

(Acceleration Command)
Set Cn015.1=2 first.
When accel. command is less than Cn023 Gain 1 is
selected.
When accel. command is greater than Cn023 Gain 2 is
selected.
When Gain 2 is active and acceleration command
becomes less than Cn023 system will automatically
switch back to Gain 1 the switch time delay can be set
by Cn020.
* accel. is acceleration
Automatic gain 1& 2 switch condition (Position
error value)
Set Cn015.1=3 first.
When position error value is less than Cn024 Gain 1 is
selected.
When position error value is greater than Cn024 Gain 2
is selected.
When Gain 2 is active and position error value
becomes less than Cn024 system will automatically
switch back to Gain 1 and the switch time delay can be
set by Cn020.
Load-Inertia ratio
LoadInertiaToMotor (J L )
LoadInertiaRatio =
100%
MotorRotorInertia(J M )
Rigidity Setting
When Auto tuning is used, set the Rigidity Level
depending on the various Gain settings for
applications such as those listed below:
Explanation
Speed Loop
Position
Loop
Speed
Loop
Integral-Time
Setting
Gain
Gain
Constant
Pn310 [1/s] Sn211 [Hz]
Sn212
[x0.2msec]
15
15
300
1
20
20
225
2
30
30
150
3
40
40
100
4
60
60
75
5
85
85
50
6
120
120
40
7
160
160
30
8
200
200
25
9
250
250
20
A

6-7

Setting Control
Chapter
Range
Mode

rps/s

18750

Pi
Pe
S

5-3-11

pulse

50000

Pi
Pe
S

5-3-11

40

x0.1

1000

Pi
Pe
S

5-5

Pi
Pe
S

5-5-1

Parameter

Name & Function

Default Unit

Setting Control
Chapter
Range Mode

Analog monitor output 1, Offset adjustment

Analog monitor output zero offset can be adjusted by
parameter. Cn027 as below.

Cn027

x40
mV

-250

250

ALL

5-6-9

x40
mV

-250

250

ALL

5-6-9

ALL

5-6-10

ALL

3-2-2

ALL

5-6-8

ALL

3-1
3-2-1

500

Hz

Pe
Pi
S

5-3-12

40

Hz

Pe
Pi

5-4-6

Hz

ALL

5-2-7

Analog monitor output 2, offset adjustment

Cn028

Analog monitor output 2, zero offset can be adjusted by

parameter. Cn028. See diagram for Monitor 1 above.

Reset parameters.
Setting
Explanation
Cn029
0
0
Disabled
Reset all Parameters to default ( Factory
1
setting)
Servo motor model code
Servo model code can be display and checked with
parameter dn-08, refer 3-2-2 dn-08 table for more
Cn030 information.
Default
AttentionBefore operate your servo motor., check this
parameter setting is compatible for servo drive and
motor. If there has any incompatible problem contact
supplier for more information.
Cooling fan running modes
(Available for JSDA-50 & JSDA-75)

Setting
Explanation
0
Auto-run by internal temperature sensor.
1
Run when Servo ON
2
Always Running.
3
Disabled.
Low Voltage Protection(AL-01) auto-reset selection
This parameter(AL-01) could be set the method of Low
Voltage Protection.
Setting
Explanation
As servo on, it shows AL-01 low voltage alarm
Cn031.1
immediately when it detect low voltage, and
0
after eliminating the situation, to reset it, servo
off is a must.
It shows BB(baseblock) immediately when it
detect low voltage, and after eliminating the
1
situation, drive would be auto-reset and
displayed Run.
Speed feed back smoothing filter
Cn032 Restrain sharp vibration noise by the setting and this
filter also delay the time of servo response.
Speed Feed-forward smoothing filter
Cn033
Smooth the speed feed-forward command.
Cn031

Cn034

Torque command smoothing filter

Restrain sharp vibration noise by the setting and this
filter delay the time of servo response.

6-8

1000
1

100
0

1000

Default

Parameter Name & Function

Unit Setting
Range

Control Chapter
Mode

Panel display content selection

Select display content for LED panel for power on
status.
Setting
Explanation
Display
data
set
and
drive status parameter.
Cn035
0
Refer 3-1
Display Un-01 ~ Un-19 content. Refer 3-2-1
1
for more information.

ExSet Cn035=1, when power on it display

21
the actual speed of motor. (content of Un-01)
Servo ID number
When
using Modbus for communication,each servo
Cn036
units has to setting a ID number. repeated ID number
will lead to communication fail.
Modbus RS-485 braud rate setting
Setting
Explanation
0
4800
Cn037.0
1
9600
2
19200
3
38400
4
57600
5
115200
PC Software RS-232 braud rate setting
Setting
Explanation
Cn037.1
0
4800
1
9600
2
19200
3
38400
Communication RS-485 selection
This parameter can be set to RS-485 communication
Cn037.2 written to the EEPROM or SRAM.
Setting
Explanation
0
Write to EEPROM
1
Write to SRAM
Communication protocol
Setting
Explanation
0
7 , N , 2 ( Modbus , ASCII )
1
7 , E , 1 ( Modbus , ASCII )
2
7 , O , 1 ( Modbus , ASCII )
Cn038
3
8 , N , 2 ( Modbus , ASCII )
4
8 , E , 1 ( Modbus , ASCII )
5
8 , O , 1 ( Modbus , ASCII )
6
8 , N , 2 ( Modbus , RTU )
7
8 , E , 1 ( Modbus , RTU )
8
8 , O , 1 ( Modbus , RTU )
Communication time-out dection
Setting non-zero value to enable this function,
Cn039 communication Time should be in the setting period
otherwise alarm message of communication time-out
will show. Setting a zero value to disable this function.
Communication response delay time
Cn040
Delay Servo response time to master control unit.

6-9

21

ALL

3-1
3-2-1

254

ALL

bps

ALL

bps

ALL

ALL

ALL

sec

20

ALL

0.5
msec

255

ALL

Torque-Control Parameter
Parameter

Name & Function

Default Unit

Linear acceleration/deceleration method

Setting
Explanation
0
Disabled.
Tn101
1
Enabled.
Enable Torque command smooth accel/decel
2
time Constant.
Linear accel/decel time period.
Time taken for the torque-command to linearly
accelerate to the rated torque level or Decelerate to
zero torque .

Tn102

Setting Control
Chapter
Range Mode

5-2-3

msec

50000

5-2-3

300

5-2-1

Analog Torque Command Ratio

Slope of voltage command / Torque command can be
adjusted.
%
300

Tn103

10V

6-10

Parameter

Name & Function

Default Unit

Setting Control
Chapter
Range Mode

Torque Command, analog input voltage offset

The offset amount can be adjusted by this parameter.

Input Voltage (V)

Tn104

mV

-10000

10000

5-2-2

100

rpm

3000

5-2-6

200

rpm

3000

5-2-6

300

rpm

3000

5-2-6

300

ALL

5-2-7

Offset
Voltage
Torque
(%)
Command

Preset Speed Limit 1. ( Torque control mode)

In Torque control, input contacts SPD1 and SPD2 can
be used to select Preset speed limit 1. As follows:
Tn105

Input Contact SPD2

0

Input Contact SPD1

1

Note: Input contacts status 1 (ON) and 0 (OFF).

Refer to 5-6-1 to set high or low input logic levels.
Preset Speed Limit 2. ( Torque control mode)
In Torque control, input contacts SPD1 and SPD2 can
be used to select Preset speed limit 2. As follows:
Tn106

Input Contact SPD2

1

Input Contact SPD1

0

Note: Input contacts status 1 (ON) and 0 (OFF)

Refer to 5-6-1 to set high or low input logic levels.
Preset Speed Limit 3. ( Torque control mode)
In Torque control, input contacts SPD1 and SPD2 can
be used to select Preset speed limit 3. As follows:Tn107

Tn108

Input Contact SPD2

1

Input Contact SPD1

1

Note: Input contacts status 1 (ON) and 0 (OFF)

Refer to 5-6-1 to set high or low input logic levels.
Torque output monitor value
When the torque level in CW or CCW direction
become greater then this value setting, the output
contact INT operate.

6-11

Parameter

Default Unit Setting

Range

Name & Function

Control Chapter
Mode

Analog Speed Limited Proportion Controller

This function used for adjusted analog voltage
command compared with the slope of speed limit
command.

Tn109

3000

rpm
/10V

100

4500

msec

10000

Torque command smooth accel/decel time

Constant.
Setting Tn101=2 to enable this function.
This function is depend on rising time of the torque
command from 0 to 63.2%.
Torque
Command (%)
100

Torque Command

Tn110
63.2
50

Tn110

Time (ms)

6-12

5-3-6

Speed-Control Parameter
Parameter

Name & Function

Sn201

Internal Speed Command 1

In Speed control, input contacts SPD1 and SPD2 can
be used to select 3 sets of internal speed command,
select for speed command 1 contact status shows
below:
Input Contact SPD2
0

Sn202

Input Contact SPD2

1

Sn204

Sn205

rpm

-3000

3000

5-3-1

200

rpm

-3000

3000

5-3-1

300

rpm

-3000

3000

5-3-1

5-3-12

S
T

5-3-6

Input Contact SPD1

0

Note: Input contacts status 1 (ON) and 0 (OFF)

Refer to 5-6-1 to set high or low input logic levels.
Internal Speed Command 3
In Speed control, input contacts SPD1 and SPD2 can
be used to select 3 sets of internal speed command,
select for speed command 3 contact status shows
below:
Input Contact SPD1
1

Note: Input contacts status 1 (ON) and 0 (OFF).

Refer to 5-6-1 to set high or low input logic levels.
Zero Speed selection Enable or Disable the zero
speed preset parameter Sn215.
Setting
Explanation
No Action. ( Sn215 zero preset is not
0
effective).
1
Set the preset value in Sn215 as zero speed.
Speed command accel/decel smooth method.
Setting
Explanation
0
By Step response
Smooth Acceleration/deceleration according
1
to the curve defined by Sn206.
Linear accel/decel time constant .Defined by
2
Sn207
S curve for Acceleration/deceleration. Defined
3
by Sn208.

6-13

Setting Control
Chapter
Range Mode

100

Input Contact SPD1

1

Note: Input contacts status 1 (ON) and 0 (OFF)

Refer to 5-6-1 to set high or low input logic levels.
Internal Speed Command 2
In Speed control, input contacts SPD1 and SPD2 can
be used to select 3 sets of internal speed command,
select for speed command 2 contact status shows
below:
Input Contact SPD2
1

Sn203

Default Unit

Parameter

Name & Function

Default Unit

Setting Control
Chapter
Range Mode

Speed command smooth accel/decel time

Constant.
Set Sn205=1 to enable this function then set the time
period for the speed to rise to 63.2% of the full speed.

Sn206

msec

msec

10000

S
T

5-3-6

S
T

5-3-6

Speed command linear accel/decel time constant.

Set Sn205=2 to enable this function then set the time
period for the speed to rise linearly to full speed.
Speed Command (%)
Ratio Speed

100
Sn207

Speed Command
50

Sn207

Time (ms)

6-14

50000

Name & Function

Parameter

Default Unit

Setting Control
Chapter
Range Mode

S curve speed command acceleration and

deceleration time setting.
Set Sn205=3 to enable this function.
In the period of Acc/Dec , drastic speed changing
might cause vibration of machine. S curve speed
command acc/dec time setting has the effect to
smooth acc/dec curve.
Speed Command (rpm)
ts=Sn208
ta=Sn209
td=Sn210

Sn208

ts

ts

ts

ta

Rule for the setting

ts
td

msec

200

msec

200

msec

Sn211

40

Hz

100

x0.2
ms

5-3-6

S
T

5-3-6

S
T

5-3-6

10

450

Pi
Pe
S

5-3-8
5-5

500

Pi
Pe
S

5-3-8
5-5

ta
t
> ts d > ts
2
2

Refer Sn208
S curve speed command deceleration time setting.

Sn210

S
T

Time

S curve speed command acceleration time setting.

Sn209

1000

Refer Sn208
Speed loop Gain 1
Speed loop gain has a direct effect on the frequency
response bandwidth of the Speed-control loop.
Without causing vibration or noise Speed-loop-gain
can be increased to obtain a faster speed response.

5000
0

5000

If Cn025 (load Inertia ratio) is set correctly, the

speed-loop-bandwidth will equal to speed-loop-gain.
Speed-loop Integral time 1

Sn212

Speed loop integral element can eliminate the steady

speed error
and react to even slight speed variations.
Decreasing Integral time can improve system rigidity.
The formula below shows the relationship between
Integral time and Speed loop Gain.
1
SpeedLoopI ntegration TimeCons tan t 5
2 SpeedLoopG a

6-15

Parameter

Speed loop Gain 2

Sn213

40

Refer to Sn211
Speed loop Integral time 2

Sn214

Sn215

Settin
Control
Chapter
g
Mode
Range
10
Pi
5-3-8
Hz

Pe
5-5
450
S
1
Pi
x0.2
5-3-8

Pe
msec
5-5
500
S

Defaul
Unit
t

Name & Functions

100

Refer to Sn212
Value of zero speed
Set the zero speed range in Sn215
When the actual speed is lower than Sn215 value, Output
contact ZS is activated.
Analog Speed Command Ratio
Slope of voltage command / Speed command can be
adjusted.

Sn216

50

rpm

4500

5-3-12

Rate
rpm

rpm
/10V

100

4500

5-3-2

mV

-10000

10000

5-3-3

rpm

100

4500

5-3-4

Analog Speed Command offset adjust

The offset amount can be adjusted by this parameter.
Input Voltage (V)

Sn217

Offset
Voltage
Speed
Command (rpm)

Sn218

Rate
Analog speed command limited
Setting Sn218 for limit the highest speed command of rpm x
1.02
analog input.

6-16

Position Control Parameter

Parameter

Name & Function

Default Unit

Position pulse command selection

Setting
Explanation
Pn301.0
0
(Pulse)+(Sign)
1
(CCW)/(CW) Pulse
2
AB-Phase pulse x 2
3
AB-Phase pulse x 4
Position- Pulse Command Logic
Pn301.1 Setting
Explanation
0
Positive Logic
1
Negative Logic
Selection for command receive of drive inhibit
mode
Pn301.2 Setting Explanation
When drive inhibit occurs, record value of
0
position command input coherently.
When drive inhibit occurs, ignore the value of
1
position command.
Electronic Gear Ratio Numerator 1
Use input contacts GN1 & GN2 to select one of four
electronic Gear Ratio Numerators.
To select Numerator 1, the statue of the input-contacts
GN1 & GN2 should be as follows:
Pn302
Input Contact GN2
0

Setting Control
Chapter
Range Mode
0

3
Pe

5-4-1

Pi
Pe

5-4-1

50000

Pi
Pe

5-4-3

50000

Pi
Pe

5-4-3

50000

Pi
Pe

5-4-3

Input Contact GN1

0

Note: Input contacts status 1 (ON) and 0 (OFF).

Refer to 5-6-1 to set high or low input logic levels.
Electronic Gear Ratio Numerator 2

Pn303

Use input contacts GN1 & GN2 to select one of four

electronic Gear Ratio Numerators.
To select Numerator 2, the statue of the input-contacts
GN1 & GN2 should be as follows:
Input Contact GN2
0

Input Contact GN1

1

Note: Input contacts status 1 (ON) and 0 (OFF).

Refer to 5-6-1 to set high or low input logic levels.

Pn304

Electronic Gear Ratio Numerator 3

Use input contacts GN1 & GN2 to select one of four
electronic Gear Ratio Numerators.
To select Numerator 3, the statue of the input-contacts
GN1 & GN2 should be as follows:
Input Contact GN2
1

Input Contact GN1

0

Note: Input contacts status 1 (ON) and 0 (OFF).

Refer to 5-6-1 to set high or low input logic levels.

6-17

Parameter

Name & Function

Pn305

Electronic Gear Ratio Numerator 4

Use input contacts GN1 & GN2 to select one of four
electronic Gear Ratio Numerators.
To select Numerator 4, the statue of the input-contacts
GN1 & GN2 should be as follows:
Input Contact GN2
1

Default Unit

50000

Pi
Pe

5-4-3

50000

Pi
Pe

5-4-3

pulse

50000

Pi
Pe

5-4-9

pulse

50000

Pi
Pe

5-4-9

pulse

50000

Pi
Pe

5-4-9

1/s

450

Pi
Pe

5-4-6
5-5

40

1/s

450

Pi
Pe

5-4-6
5-5

100

Pi
Pe

5-4-6
5-5

Input Contact GN1

1

Note: Input contacts status 1 (ON) and 0 (OFF).

Refer to 5-6-1 to set high or low input logic levels.
Electronic Gear Ratio Denominator
Set the calculated Electronic Gear Ratio Denominator
in Pn 306. ( Refer to section 5-4-3).
Pn306 Final Electronic Gear Ratio should comply with the
formula below.

1
ElectronicGearRatio 200
200
Pn307

Pn308

Pn309

Pn310

Position complete value

Set a value for In position output signal.
10
When the Position pulse error value is less then Pn307
output-contact INP (In position output signal) will be
activated.
Incorrect position Error band Upper limit.
When the Position error value is higher then number of
50000
pulses set in Pn308, an Alarm message
AL-11(Position error value alarm) will be displayed.
Incorrect position Error band lower limit.
When the Position error value is lower then number of 50000
pulses set in Pn309, an Alarm message
AL-11(Position error value alarm) will be displayed.
Position Loop Gain 1
Without causing vibration or noise on the mechanical
system the position loop gain value can be increased
to speed up response and shorten the positioning time.
Generally, the position loop bandwidth should not be
40
higher then speed loop bandwidth. The relationship is
according to the formula below:

PositionLoopGain 2

SpeedLoopGain

Position Loop Gain 2

Pn311

Pn312

Setting Control
Chapter
Range Mode

Refer to Pn310
Position Loop Feed Forward Gain
It can be used to reduce the track error of position
control and speed up the response.
If the feed forward gain is too large, it might cause
speed
Overshoot and in position oscillations which result in
the repeated ON/OFF operation of the output contact
INP(In Positionoutput signal).

6-18

Name & Function

Parameter

Default Unit

Setting Control
Chapter
Range Mode

Position command smooth

Acceleration/Deceleration Time Constant
Set the time period for the Position command pulse
frequency to rise from 0 to 63.2%.
Position Pulse Command Frequency (%)
100

Position Pulse Command Frequency

Pn313

10

msec

10000

Pi
Pe

5-4-4

Pi
Pe

5-4-5

63.2
50

Time (ms)

Pn313

Positioning Command Direction Definition

CCW

CW

Pn314

Pn315

Setting
Explanation
0
(CW) .Clockwise
1
(CCW). Counter Clockwise
Pulse Error Clear Modes.
Setting
Explanation
Once CLR signal is activated, it eliminates,
0
the Pulse error amount.
Once CLR signal is activated, following takes
place:
The position command is cancelled.
1
Motor rotation is interrupted
Pulse error amount is cleared.
Machine home reference is reset
Once CLR signal is activated, following takes
place:2
The position command is cancelled..
Motor rotation is interrupted
Pulse error amount is cleared.

6-19

Pe

Pi
Pe

Pi

5-4-7

Parameter

Name & Function

Default Unit

Internal Position Command Mode

Setting
Explanation
Pn316
0
Absolute Position
1
Incremental Position
Internal Position Command Hold (PHOLD)
program select
Setting
Explanation
When
PHOLD
is
active then received PTRG
Pn316.1
0
signal. servomotor will be proceed internal
posistion command from PHOLD position.
When PHOLD is active then received PTRG
1
signal. Servomotor will operate interal position
command of current selection.
Internal Position Command 1 Rotation Number
Set the Rotation number of the internal Position
Pn317 Command 1
Use input contacts POS1~POS4 to select Refer to
5-4-2.
Internal Position Command 1 - Pulse Number
Set the rotation pulse number of internal position
Pn318 Command 1
Internal Position Command 1 =Pn317(Rotation Number)
x
Pulse number of One Rotate x 4 + Pn318(Pulse number)

Pn319

Pn320

Internal Position Command 1 - Move Speed

Setting the Move Speed of internal Position Command
1
Internal Position Command 2-Rotation Number

Pi

5-4-2

Pi

5-4-2

rev

-30000

30000

Pi

5-4-2

pulse

-32767

32767

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

Pi

5-4-2

0
0

Please refer to Pn317

Internal Position Command 2-Pulse Number

Pn321

Please refer to Pn318

Internal Position Command 2-Move Speed

Pn322

Please refer to Pn319

Internal Position Command 3-Rotation Number

Pn323

Please refer to Pn317

Internal Position Command 3-Pulse Number

Pn324

Please refer to Pn318

Internal Position Command 3-Move Speed

Pn325

Please refer to Pn319

Internal Position Command 4 -Rotation Number

Pn326

Please refer to Pn317

Internal Position Command 4-Pulse Number

Pn327

Please refer to Pn318

Internal Position Command 4-Move Speed

Pn328

Please refer to Pn319

6-20

Setting Control
Chapter
Range Mode

3000
-30000
rev

30000
-32767
pulse

32767
0
rpm

3000
-30000
rev

30000
-32767
pulse

32767
0
rpm

3000
-30000
rev

30000
-32767
pulse

32767
0
rpm

3000
rpm

Parameter

Name & Function

Default Unit

Internal Position Command 5 -Rotation Number

Pn329

Please refer to Pn317

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

Internal Position Command 5-Pulse Number

Pn330

Please refer to Pn318

Internal Position Command 5-Move Speed

Pn331

Please refer to Pn319

Internal Position Command 6 -Rotation Number

Pn332

Please refer to Pn317

Internal Position Command 6-Pulse Number

Pn333

Please refer to Pn318

Internal Position Command 6-Move Speed

Pn334

Please refer to Pn319

Internal Position Command 7 -Rotation Number

Pn335

Please refer to Pn317

Internal Position Command 7-Pulse Number

Pn336

Please refer to Pn318

Internal Position Command 7-Move Speed

Pn337

Please refer to Pn319

Internal Position Command 8 -Rotation Number

Pn338

Please refer to Pn317

Internal Position Command 8-Pulse Number

Pn339

Please refer to Pn318

Internal Position Command 8-Move Speed

Pn340

Please refer to Pn319

Internal Position Command 9 -Rotation Number

Pn341

Please refer to Pn317

Internal Position Command 9-Pulse Number

Pn342

Please refer to Pn318

Internal Position Command 9-Move Speed

Pn343

Please refer to Pn319

Internal Position Command 10 -Rotation Number

Pn344

Please refer to Pn317

Internal Position Command 10-Pulse Number

Pn345

Please refer to Pn318

6-21

Setting Control
Chapter
Range Mode
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767

Parameter

Name & Function

Default Unit

Internal Position Command 10-Move Speed

Pn346

Please refer to Pn319

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

pulse

rpm

rev

Internal Position Command 11 -Rotation Number

Pn347

Please refer to Pn317

Internal Position Command 11-Pulse Number

Pn348

Please refer to Pn318

Internal Position Command 11-Move Speed

Pn349

Please refer to Pn319

Internal Position Command 12-Rotation Number

Pn350

Please refer to Pn317

Internal Position Command 12-Pulse Number

Pn351

Please refer to Pn318

Internal Position Command 12-Move Speed

Pn352

Please refer to Pn319

Internal Position Command 13 -Rotation Number

Pn353

Please refer to Pn317

Internal Position Command 13-Pulse Number

Pn354

Please refer to Pn318

Internal Position Command 13-Move Speed

Pn355

Please refer to Pn319

Internal Position Command 14 -Rotation Number

Pn356

Please refer to Pn317

Internal Position Command 14-Pulse Number

Pn357

Please refer to Pn318

Internal Position Command 14-Move Speed

Pn358

Please refer to Pn319

Internal Position Command 15 -Rotation Number

Pn359

Please refer to Pn317

Internal Position Command 15-Pulse Number

Pn360

Please refer to Pn318

Internal Position Command 15-Move Speed

Pn361

Please refer to Pn319

Internal Position Command 16 -Rotation Number

Pn362

Please refer to Pn317

6-22

Setting Control
Chapter
Range Mode
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000
-32767
Pi
5-4-2

32767
0
Pi
5-4-2

3000
-30000
Pi
5-4-2

30000

Parameter

Name & Function

Internal Position Command 16-Pulse Number

Pn363

Please refer to Pn318

Internal Position Command 16-Move Speed

Pn364

Setting Control
Chapter
Range Mode
-32767
pulse
Pi
5-4-2

32767
0
rpm
Pi
5-4-2

3000

Default Unit

Please refer to Pn319

Setting for HOME routine.

Setting
Explanation
Once the home routine is activated, motor will s
for Home Position switch in 1st speed in CCW
direction.
Input contacts CCWL or CWL can be used as
Home Reference Switch.
Once Home reference switch is detected, then
0
Contacts CCWL and CWL will act as normal M
limits again.
Note:
When using this function, Pn365.1 can not be s
or 2. Cn002.1 ( selection for CCWL and CWL
be set to set to 0.
Once the home routine is activated, motor will
search for Home
Position switch in 1st speed in CW direction.
Input contacts CCWL or CWL can be used as
the Home Reference Switch.
Once Home position is detected, then input
contacts CCWL and CWL will act as normal
1
max. limits again.
Note:
Pn365.0
When using this function, Pn365.1 can not be
set to 1 or 2.
Cn002.1 ( selection for CCWL and CWL)
must be set to 0.
Once the home routine is activated , motor will
search for Home position switch in 1st speed in
CCW direction and sets the Home
reference position as soon as the input contact
ORG is activated.
2
If Pn365.1=2, it will directly find the closest
Rising-Edge of ORG to be the Home position
(without a need for Home Reference),
then it stops in accordance with Pn365.3
setting.
Once the home routine is activated , motor will
search for Home
Position switch in 1st speed in CW direction
and sets the reference Home position as soon
as the input contact ORG is activated.
3
If Pn365.1=2, it will directly find the closest
rising -Edge of ORG to be the Home position
(without a need for Home reference),
then it stops in accordance with Pn365.3
setting.

6-23

Pi
Pe

5-4-8

Parameter

Name & Functions

Default Unit

Once the home routine is activated , motor will

search for Home
position in 1st speed in CCW direction and
sets the Home reference position as soon as
4
the nearest Z (marker pulse) is detected.
When using this function, set Pn365.1=2 .
After setting the Z Phase to be the Home, it
stops in accordance with the setting of
Pn365.0
Pn365.3.
Once the home routine is activated , motor will
search for Home position in 1st speed in CW
direction and sets the Home reference
position as soon as the nearest Z (marker
5
pulse) is detected.
When using this function, set Pn365.1=2 .
After setting the Z Phase to be the Home, it
stops in accordance with the setting of
Pn365.3.
Once Reference Home switch or Signal, is found it
sets the search method for the Home position.
Setting
Explanation
Once the Home Reference switch or signal is
detected, motor reverses direction in 2nd
speed to find the nearest Z. Phase pulse and
0
sets this as the Home position,
then stops in accordance with Pn365.3
setting method.
Once
the Home Reference switch or signal is
Pn365.1
detected, motor Continues in its direction in
1
2nd speed to find the nearest Z Phase pulse
and sets this as the Home position, then stops
in accordance with Pn365.3 setting method.
When Pn365.0=2 or 3, it finds the rising edge
of ORG to be the Home position, then stops in
accordance with Pn365.3.
2
When Pn365.0=4 or 5, it finds Z Phase pulse
to be the Home, then stops in accordance
with Pn365.3.
Setting of Home Routine Start method
Setting
Explanation
0
Homing routine is Disabled.
On power up and activation of Servo on the
home routine is started automatically.
Pn365.2
1
This method is useful for applications that do
not require repeated home routines. No
external home reference switch is required.
Use SHOME input contact to start a home
routine.
2
In position mode, SHOME can be used to
start a home routine at any moment.

6-24

Setting Control
Chapter
Range Mode

Pi
Pe

5-4-8

Pi
Pe

5-4-8

Parameter

Name & Function

Default Unit

Setting of stopping mode after finding Home

signal.
Setting
Explanation
After detecting the Home signal, it sets this
position to be the Home reference (Un-14
encoder feed back rotating number and
Un-15 encoder feed back pulse number are
0
Pn365.3
all 0), motor decelerates and stops.
Then it reverses direction in 2nd speed to
detect the Home Position again then it
decelerates and stops..
After detecting the Home signal, it sets this
position to be the Home reference (Un-14
1
encoder feed back rotating number and
Un-15 encoder feed back pulse number are
all 0), motor decelerates and stops.
Machine Home reference search speed. 1st speed
Pn366 ( Fast)
HOME Refeence search speed . Speed 1.
Machine Home position search speed. 2nd Speed
Pn367 (Slow)
Home position search speed . Speed 2.
Home position offset . Number of revolutions.
Once the searched home position is found in
accordance with Pn365 (Home routine mode), then it
Pn368
will search by a number of revolutions and pulses set in
parameters Pn368 and Pn 369 to find the new (off set)
Home position.
Home position offset . Number of Pulses.
Pn369

Home Offset position = Pn368(Rotate Number) x

Number of Encoder Pulse per Rotation x 4
+ Pn369(Pulse Number)

6-25

100

rpm

50

rpm

rev

pulse

Setting Control
Chapter
Range Mode

Pi
Pe

5-4-8

Pi
Pe

5-4-8

Pi
Pe

5-4-8

-30000

30000

Pi
Pe

5-4-8

-32767

32767

Pi
Pe

5-4-8

2000
0

500

Parameter

Name & Function

Default Unit

Setting Control
Chapter
Range Mode

S-Curve Time Constant for Internal Position

command(TSL)
S-curve time constant generator can smoothen the
command, it pro vides continuou s speed and
acceleration which not only better the motor
characteristic of acc/dec but also helps the motor to
operate more smoothly in machinery structure.S-curve
time constant generator is only applicable to the mode
of internal position command input. When position
command input switch to external position pulse, the
speed and acceleration are already constant, so it
doesnt use the S-curve time constant generator.

TACC > TSL

a(t)
t
Pn370

TSL
2

TACC
(a)

TACC = TSL

TSL
2

Pn371

TACC

TSL
2

x0.4
ms

5000

Pi

5-4-4

x0.4
ms

5000

Pi

5-4-4

TACC < TSL

TSL
2

Notes
1. Rule of setting: Pn371(TACC)Pn370(TSL).
2. When Pn370 sets as 0, the S-curve time constant
will be disabled.
S-Curve Time Constant for Internal Position
command(TACC)
Please refer to Pn370

6-26

Quick Set-up Parameters

Name & Function

Parameter

Default Unit

Speed Loop Gain 1.

( Same function as Sn211)
Speed loop gain has a direct effect on the frequency
response bandwidth of the Speed-control loop.
qn401 Without causing vibration or noise Speed-loop-gain
can be increased to obtain a faster speed response.
If Cn025 (load Inertia ratio) is correctly set, the
speed-loop-bandwidth will equal to speed-loop-gain.
Speed-loop Integral time 1. (Same function as

Setting
Range

Control
Mode

Chapter

40

Hz

10

450

Pi
Pe
S

5-3-8
5-5

100

x0.2
ms

500

Pi
Pe
S

5-3-8
5-5

40

Hz

100

x0.2
ms

10

450
1

500

Pi
Pe
S
Pi
Pe
S

40

1/s

450

Pi
Pe

5-4-6
5-5

40

1/s

450

Pi
Pe

5-4-6
5-5

100

Pi
Pe

5-4-6
5-5

Sn212)

Speed loop integral element can eliminate the steady

speed error
and react to even slight speed variations.
qn402
Decreasing Integral time can improve system rigidity.
The formula below shows the relationship between
Integral time and Speed loop Gain.
SpeedLoopI ntegration TimeCons tan t 5

1
2 SpeedLoopG ain

Speed Loop Gain 2.

(Same function as
qn403 Sn213)
Refer to qn401
Speed Loop Integration Time Constant 2.
qn404 (Same function as Sn214)
Refer to qn402
Position Loop Gain 1.
(Same function as

5-3-8
5-5
5-3-8
5-5

Pn310)

Without causing vibration or noise on the mechanical

system the position loop gain value can be
increased to speed up response and shorten the
qn405 positioning time.
Generally, the position loop bandwidth should not be
higher then speed loop bandwidth. The relationship
is according to the formula below:

PositionLoopGain 2
Position Loop Gain 2

SpeedLoopGain

5
(Same function as

qn406 Pn311)
Please refer to qn405
Position Loop Feed Forward Gain
It can be used to reduce the follow up error of
position control and speed up the response.
If the feed forward gain is too large, it might cause
qn407
speed
Overshoot and in position oscillations which result in
the repeated ON/OFF operation of the output
contact
INP(In Position output signal).

6-27

Multi-Function Input Parameters

All digital inputs D1 to D13 are programmable and can be set to one of the funhctions listed below.
Hn 501 which includes Hn 501.0 ,Hn501.1, Hn501.2 is used for digital input 1 ( D1-1).
Hn502 to Hn513 are used for setting digital inputs 2 to 13.( D1-2 to D1-13).
Parameter

Name & Function

Default Unit

Setting
Range

Control
Mode

Chapter

ALL

5-6-1

DI-1
Seting

Explanation
Functions
01
Servo On
02
Alarm Reset
03
PI/P Switching
04
CCW Limit
05
CW Limit
06
External Torque Limit
07
Clear Pulse Error Value
08
Servo Lock
09
Emergency Stop
0A
Speed 1
0B
Speed 2
0C
Control Mode Switch
Position Command Inhibit
Hn501.0 0D
Speed Inverse
Hn501.1 0E
0F
Gain Select
Electronic Gear Ratio Numerator
10
GN1
1
Electronic Gear Ratio Numerator
11
GN2
2
12
PTRG Position Trigger
13
PHOLD Position Hold
14
SHOME Start Home
Home Position Reference
15
ORG
(Origin)
16
POS1 Internal Position select 1
17
POS2 Internal Position select 2
18
POS3 Internal Position select 3
19
POS4 Internal Position select 4
1A
TRQINV Torque Inverse
1B
RS1 Torque CW Selecting
1C
RS2 Torque CCW Selecting
DI-1 Logic State. NO/NC Selection
Setting
Explanatoin
Input contact state. NO (Normally Open).
Hn501.2
0
Connecting (IG24) to inputs, enables the
selected function.
1
Input contact state. NC (Normally Closed).
Disconnecting (IG24) from inputs, enables
the selected function.
Signal
SON
ALRS
PCNT
CCWL
CWL
TLMT
CLR
LOK
EMC
SPD1
SPD2
MDC
INH
SPDINV
G-SEL

01

01

26

New setting will become effective after re-cycling the power.

Warning! If any of programmable Inputs of DI-1 ~ DI-13 are set for the same type of function
then the logic state selection ( NO or NC selection) for these inputs must be the same type.
Otherwise an Alarm will be displayed. AL-07 (Abnormal DI/DO programming).

6-28

Parameter

Name & Function

Signal

Default

Unit

002

003

104

105

006

007

008

009

00A

00B

00C

00E

DI-2
Hn502

Plearse refer to Hn501

DI-3

Hn503

Plearse refer to Hn501

DI-4

Hn504

Plearse refer to Hn501

DI-5

Hn505

Plearse refer to Hn501

DI-6

Hn506

Plearse refer to Hn501

DI-7

Hn507

Plearse refer to Hn501

DI-8

Hn508

Plearse refer to Hn501

DI-9

Hn509

Plearse refer to Hn501

DI-10

Hn510

Plearse refer to Hn501

DI-11

Hn511

Plearse refer to Hn501

DI-12

Hn512

Plearse refer to Hn501

DI-13

Hn513

Plearse refer to Hn501

Setting
Range
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C
001

11C

New setting will become effective after re-cycling the power.

Warning! If any of programmable Inputs of DI-1 ~ DI-13 are set for the same type of function
then the logic state selection ( NO or NC selection) for these inputs must be the same type.
Otherwise an Alarm will be displayed. AL-07 (Abnormal DI/DO programming).

6-29

Control
Mode

Chapter

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

Parameter

Name & Function

DO-1
Setting
Signal
RDY
ALM
ZS
BI
INS
INP
HOME
INT

Default Unit

Explanation
Functions
Servo Ready
Alarm
Zero Speed
Brake Signal
In Speed
In Position
HOME
In Torque

01
02
03
04
05
06
07
08
DO-1
Hn514.2 Setting
Explanation
0
Close, when the output is activated.
1
Open, when the output is activated.
DO-2
Hn515
Plearse refer to Hn514
Hn514.0
Hn514.1

01

002

003

006

DO-3
Hn516

Plearse refer to Hn514

DO-4

Hn517

Plearse refer to Hn514

Setting
Range

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

ALL

5-6-1

1
001

108
001

108
001

108

Warning! If any of programmable Inputs of DI-1 ~ DI-13 are set for the same type of function
then the logic state selection ( NO or NC selection) for these inputs must be the same type.

6-30

Chapter

01

08

New setting will become effective after re-cycling the power.

Otherwise an Alarm will be displayed. AL-07 (Abnormal DI/DO programming).

Control
Mode

Parameter
Signal

Hn518

Name & Function

Default Unit

Digital input control method selection.

Select digital input (13 pins) control method by
external terminal or communication. Convert Binary
code to Hex code for setting this parameter. DI and
binary bits table as below.
Ex. DI-1 is bit 0 and DI-13 is bit 12.

DI-[ ] DI-13 DI-12

DI-1

0
bit
12
11

Binary code representation

0 Digital input control by external terminal.
1 Digital input control by communication.

H0000

Set H0000 for Hn518 represent DI-1 ~ DI-13 are

controlled by external terminal and set H1FFF
represent
all
terminal
is
controlled
by
communication.
Ex. Set DI (1, 3, 6, 10, 12) for communication control
other pins by external terminal;
The corresponding binary code is :[0 1010 0010
0101] convert to Hex code is : [H 0A25]for entering
parameter.
For the setting Bit0 (DI-1) is control by
communication and Bit1 (DI-2) is control by external
terminal .etc

Hn519

Setting digital input status in communication

mode
Change Hn519 Hex code for setting digital input
status of communication control mode; Setting
method refer Hn518.
Binary code representation
0 : digital input contact OFF
H0000
1 : digital input contact ON
Set H0000 for Hn518 represent DI-1 ~ DI-13 are
controlled by external terminal and set H1FFF
represent all terminal is controlled by
communication.
P.S.)This parameter should co-operate with
Hn518.

6-31

Setting
Range

H0000

H1FFF

Control
Mode

Chapter

ALL

5-6-1
7

ALL

5-6-1
7

(HEX)

H0000

H1FFF
(HEX)

Display Parameter
Parameter

Signal

Display

Unit

Explanation

Un-01

Actual Motor Speed

rpm

Un-02

Actual Motor Torque

It displays the torque as a percentage of the rated torue.

Ex: 20 are displayed. It means that the motor torque output is 20% of
rated torque.

Un-03

Regenerative load rate

Value for the processable regenerative power as 100% .

Displays regenerative power consumption in 10-s cycle.

Un-04

Accumulated load rate

Value for the rated torque as 100%.

Displays effective torque in 10-s cyle.

Un-05

Max load rate

Max value of accumulated load rate

Un-06

Speed Command

Un-07

Position Error Value

pulse feedback.

Un-08

Position Feed-back Value

pulse The accumulated number of pulses from the encoder.

Un-09

ExternalVoltage Command

Un-10
Un-11

(Vdc Bus)Main Loop

Voltage
External Spped Limit
Command Value

rpm

Motor Speed is displayed in rpm.

Speed command is displayed in rpm.

Error between position command value and the actual position

External analog voltage command value in volts.

DC Bus voltage in Volts.

rpm

External speed limit value in rpm.

Un-12

External CCW Torque Limit

Command Value

Ex: Display 100. Means current external CCW torque limit command is
set to 100 %.

Un-13

External CW Torque
LimitCommand Value

Ex: Display 100. Means current external CW toque limit command is set
to 100%.

Un-14

Motor feed back Rotation

value (absolute value)

rev

After power on, it displays motor rotation number as an absolute value.

Un-15

Motor feed back Less

then 1 rotation pulse
value(absolute value)

Un-16

Pulse command rotation

value(absolute value)

Un-17

Pulse command Less

then 1 rotation pulse
value(absolute value)

Un-18

Torque command

Un-19

Load inertia

Un-20

Digital Output status(Do)

Un-21

Digital Input status(Di)

Un-22

Motor speed feedback

(Filter)

Motor speed by using filter.

Communication Address: RS485H0616, RS23261E

Un-23

Currently Fault Status Read

(Communication)

Reads currently fault status by using communication.

Communication Address: RS485H0617

After power on, it displays the number of pulses for an incomplete

pulse revolution of the motor as an absolute value.

rev

After power on, it displays pulse command input rotation number in

absolute value.
After power on, it displays pulse command input for an incomplete

pulse rotation. pulse value is an absolute value.

%

x0.1

It displays the torque command as a percentage of the rated torque.

Ex: Display. 50.Means current motor torque command is 50% of rated
torque.
When Cn002.2=0(Auto gain adjust disabled), it displays the current
preset load inertia ratio from parameter Cn025.
When Cn002.2=1(Auto gain adjust enabled), it displays the current
estimated load inertia ratio.

The status of digital output contact(Do) represented in

hexadecimal.
Ex : H00XX (0000 0000 Do-8/7/6/5 Do-4/3/2/1)
The status of digital input contact(DI) represented in
hexadecimal.
Ex : HXXXX (000Di-13 Di-12/11/10/9 Di-8/7/6/5 Di-4/3/2/1)

6-32

Diagnosis Parameter
Parameter
dn-01
dn-02
dn-03
dn-04
dn-05
dn-06
dn-07
dn-08
dn-09

Name & Function

Selected control mode
Output terminal signal status.
Input terminal signal status.
Software version
JOG mode operation
Hold position.
Auto offset adjustment of external analog command voltage.
Servo model code.
ASIC software version display

6-33

Chapter

3-2-2

Chapter 7 Communications function

7-1 Communications function ( RS-232 & RS-485 )
The Servo drive provides RS232 communication. The description below shows the communication wiring and
communication protocol.

7-1-1 Communication wiring

RS-232 Wiring

Driver terminal MD-Type 9Pins

PC terminal D-Type 9Pins(female)

Pin 4 and Pin 6 is a close loop

Pin 7 and Pin 8 is a close loop

7-1

RS-485 Wiring

Driver terminal MD-Type 8Pins

Pin

Description

Receive Data

RS-232 / RS-485
Description

Name
RxD

Name

Serial transmission +

Data +

Serial transmission -

Data -

Ground

GND

Power Supply

+ VS

Transmit Data

TxD

Ground

GND

Serial transmission +

Data+

Serial transmission -

Data -

6
7

Power Supply

7-2

RS-232/RS-485 communication parameter

Parameter

Name & Function

Default Unit

Servo ID number
Cn036

When using Modbus for communication,each servo

units has to setting a ID number. repeated ID number

Setting

Control

Range

Mode

Chapter

0
1

ALL

ALL

ALL

ALL

ALL

254

will lead to communication fail.

Modbus RS-485 braud rate setting
Setting
Cn037.0

Explanation

4800

9600

19200

38400

57600

115200

0
1

bps

PC Software RS-232 braud rate setting

Cn037.1

Setting

Explanation

4800

9600

19200

38400

0
1

bps

RS-485 communication selection

Cn037.2

This parameter can be set to RS-485 communication

written to the EEPROM or SRAM.
Setting

Explanation

Write to EEPROM

Write to SRAM

0
X

Communication protocol
Setting

Cn038

Explanation

7 , N , 2 ( Modbus , ASCII )

7 , E , 1 ( Modbus , ASCII )

7 , O , 1 ( Modbus , ASCII )

8 , N , 2 ( Modbus , ASCII )

8 , E , 1 ( Modbus , ASCII )

8 , O , 1 ( Modbus , ASCII )

8 , N , 2 ( Modbus , RTU )

8 , E , 1 ( Modbus , RTU )

8 , O , 1 ( Modbus , RTU )

0
0

7-3

Parameter

Default

Name & Function

Unit

Setting

Control

Range

Mode

Chapter

Communication time-out dection

Cn039

Setting non-zero value to enable this function,

communication Time should be in the setting period

0
0

sec

ALL

ALL

20

otherwise alarm message of communication time-out

will show. Setting a zero value to disable this function.
Communication response delay time
Cn040

Delay Servo response time to master control unit.

7-4

0.5
msec

255

Parameter

Name & Function

Signal

Default Unit

Setting

Control

Range

Mode

Chapter

Digital input control method selection.

Select digital input (13 pins) control method by
external terminal or communication. Convert Binary
code to Hex code for setting this parameter. DI and
binary bits table as below.
Ex. DI-1 is bit 0 and DI-13 is bit 12.
DI-[ ]

DI-13

DI-12

bit

12

11

DI-1

Binary code representation :

H0000

0 Digital input control by external terminal.

1 Digital input control by communication.

H0000

Hn518

Set H0000 for Hn518 represent DI-1 ~ DI-13 are

all

terminal

is

controlled

ALL

5-6-1
7

(HEX)

controlled by external terminal and set H1FFF

represent

H1FFF

by

communication.
Ex. Set DI (1, 3, 6, 10, 12) for communication control
other pins by external terminal;
The corresponding binary code is :[0 1010 0010
0101] convert to Hex code is : [H 0A25]for entering
parameter.
For the setting Bit0 (DI-1) is control by
communication and Bit1 (DI-2) is control by external
terminal .etc
Setting digital input status in communication
mode
Change Hn519 Hex code for setting digital input
status of communication control mode; Setting
H0000

method refer Hn518.

Binary code representation

Hn519

0 : digital input contact OFF

H0000

1 : digital input contact ON

Set H0000 for Hn518 represent DI-1 ~ DI-13 are
controlled by external terminal and set H1FFF
represent all terminal is controlled by
communication.
P.S.)This parameter should co-operate with
Hn518.
7-5

H1FFF
(HEX)

ALL

5-6-1
7

7-1-2 RS-232 Communication protocol and format

Baud rate

9600bps (Selection by Cn037.1 )

Parity

No

Data bit

Stop bit

Symbol H in folling sentence is for Hex representation.

(1) Read a word from servo drive  Function code format: R5XxSs
Xx : A request to read register Xx from slave device( Unit :Byte, Hex representation)
Ss : Check Sum Ss =R+5+X+x ( Unit :Byte, Hex representation)
Ex1: Read register address 30H and
( ConvertR530into ASCII codes )
Check Sum=52H+35H+33H+30H=EA H
R

Obtain Function code for read register address 30H:R530EA

Servo drive response : %XxYySs
Ss is Check Sum, Ss=%+X+x+Y+y
Response message of example 1:
0008H is the data store in register address 30H:
Check Sum=25H+30H+30H+30H+38H=EDH
% 0

0 0

Drive response message:%0008ED

* When function code incorrect , drive response :!(ASCII code: 21H )

7-6

(2) Read consecutive 2 words from drive  Function code format: L5NnSs
Nn : A request to read register Nn from slave device ( Unit :Byte, Hex representation)
Ss : Check SumSs =L+5+N+n ( Unit : Byte, Hex representation)
Ex2: Read data from register address 60H and
( ConvertL560into ASCII codes )
Check Sum=4CH+35H+36H+30H=E7
L

Obtain Function code for read register address 60H:L560E7

Servo drive response: %XxYyAaBbSs
Ss is Check SumSs=%+X+x+Y+y +A+a+B+b
XxYy is the data store in register address Nn+1,
AaBb is the data store in register address Nn
Response message of example 2:
0001 000AH is the data store in register 60H
Check Sum=25H+30H+30H+30H+31H+30H+30H +30H+41H=1B7H
%

Drive response message:%0001000AB7

* When function code incorrect , drive response :!(ASCII code: 21H )

7-7

(3) Write a word to drive  Function code format: W5XxYyZzSs

Xx : Address for write data ( Unit :ByteHex representation)
YyZz : Writes the data contents ( Unit :word, Hex representation)
Ss : Check SumSs =W+5+X+x+Y+y+Z+z ( Unit :Byte, Hex representation)
Ex3Write data 0008H to register 30H
( ConvertW5300008into ASCII codes )
Check Sum=57H+35H+33H+30H+30H+30H+30H+38H=1B7H
W

Obtain Function code for write data 0008H to register 30H : W5300008B7
Drive response message :%(ASCII code :25H)
* When function code incorrect , drive response :!(ASCII code: 21H )
(4) Write consecutive 2 words to drive  Function code format: M5NnXxYyAaBbSs
Nn : Address for write data( Unit :ByteHex representation)
XxYy : Writes the data contents of address Nn+1 ( Unit :WordHex representation)
AaBb : Writes the data contents of address Nn ( Unit :WordHex representation)
Ss : Check Sum , Ss =M+5+N+n+X+x+Y+y+A+a+B+b ( Unit :ByteHex representation)
Ex4: Write data 0002 000BH to register 60H
( ConvertM5600002000Binto ASCII codes )
Check Sum=4DH+35H+36H+30H+30H+30H+30H+32H+30H+30H+30H+42H =27CH
M

Obtain Function code for write data 0002000BH to register 60H

M5600002000B7C
Drive response message:%(ASCII code :25H )
* When function code incorrect , drive response :!(ASCII code: 21H )

7-8

7-1-3 Modbus communication protocol for RS-485

The MODBUS protocol allows an easy communication within types of network architectures,before start to
communication with slave device, set the ID number ( Cn036 ) for Servo drive respectively, server distinguish ID
number for controlling specific client station.
Standard Modbus networks combine two transmission modes: ASCII or RTU: ASCII(American Standard Code
for information interchange) Mode and RTU (Remote Terminal Unit) Mode, Use Cn038 to select ASCII or RTU
mode.

Coding method
ASCII Mode
8-bits Data consist of two ASCII code.
Ex: Data 26H 1-byte , the 26 convert to ASCII code is include character 2 <32H> and 6 <36H>
ASCII Chart ( 0 ~ 9 and A ~ F ):
Character

ASCII code(Hex)

30H

31H

32H

33H

34H

35H

36H

37H

Character

ASCII code(Hex)

38H

39H

41H

42H

43H

44H

45H

46H

RTU Mode
Each 8bits is consist of 2 Hex number (4-bits per Hex number).
Ex.: Data 26H, the data length is 1-byte.

7-9

ASCII Mode Framing

10 bits Frame (7-bits Data)
7N2

Start
bit

Stop
bit

Stop
bit

Data:7 bits
Character Frame10 bits

7E1

Start
bit

Even
parity

Stop
bit

Data:7 bits
Character Frame:10 bits

7O1

Start
bit

Odd
parity

Stop
bit

Data:7 bits
Character Frame:10 bits
11 bits Frame8-bits Data

8N2

Start
bit

Stop
bit

Stop
bit

Data:8 bits
Character Frame:11 bits

8E1

Start
bit

Even
parity

Stop
bit

Data:8 bits
Character Frame:11 bits

8O1

Start
bit

Odd
parity

Stop
bit

Data:8 bits
Character Frame:11 bits

7-10

ASCII Mode Framing

Symbol

Name

STX

Comm. start

Description
3AH, Char :
Include 2 ASCII code within 1-byte

ADR

Slave address

Comm. add : 1 ~ 254 convert to Hex representation ;

Ex. Servo drive ADR is No.20 convert to 14H ;
ADR = 1 , 4 1 = 31H , 4 = 34H
Include 2 ASCII code within 1-byte

Function Code

Function code

Function codes : 03H : Read the register contents,

06H : Write Single Register , 08H : Diagnostic function,
10H : Write Multipile Registers

DATA(n-1)

Data

DATA(0)

n-word = 2n-byte (ASCII numbers : 4n ), n30

The format of data is depend on Function code

LRC

Check code

Include 2 ASCII code within 1-byte

END 1

END 1 (CR)

0DHChar \ r

END 0

END 0 (LF)

0AHChar \ n

RTU Mode
Symbol

Name

STX

Comm. start

Description
Excess comm. loss time setting 10ms
1-byte

ADR

Slave address

Comm. address : 1 ~ 254convert to Hex representation ;

Ex. Comm. address = 20 convert representation to 14 Hex, ADR
= 14H
1-byte

Function Code

Function code

Function codes : 03H : Read the register contents,

06H : Write Single Register , 08HDiagnostic function,
10H : Write Multipile Registers

DATA(n-1)

Data

DATA(0)

n-word = 2n-byten30
The format of data is depend on Function code

CRC-Low

Checking code-LO

1-byte

CRC-High

Checking code-HI

1-byte

END 0

End 0

Excess comm. loss time setting 10ms

7-11

Common function codes

03H : Read the register contents
Continuous read N words. * Largest number of N is 29 (1DH)
Ex.: Read two words ( register 0200H and 0201H ) from Slave address 01H.

ASCII Mode
Query PC Servo
STX

:
0

ADR

Function Code

Register
ADD.

(Hi)
(Lo)

0
3

STX

:
0

ADR

Function Code

Servo PC (ERROR)
STX
ADR

:
0
1

Function

Code

Data length

Exception

(byte)

code

0
0
0

Data length

(word)

0
2
F

LRC

Response Servo PC OK)

(Hi)

Data of
0200H

(Lo)
(Hi)

Data of
0201H

(Lo)

END1 (CR)

(0DH)

END0 (LF)

(0AH)

0
0

LRC

7
A

END1 (CR)

(0DH)

END0 (LF)

(0AH)

1
F
4
0
E

LRC

END1 (CR)

(0DH)

END0 (LF)

(0AH)

RTU Mode
Query PC Servo

Response Servo PC (OK)

Servo PC (ERROR)

ADR

01H

ADR

01H

ADR

01H

Function Code

03H

Function Code

03H

Function Code

83H

Register

(Hi)

02H

Data (Byte)

04H

Exception

02H

ADD

(Lo)

00H

Data of

(Hi)

00H

CRC(Lo)

C0H

Data length

00H

0200H

(Lo)

BAH

CRC(Hi)

F1H

(word)

02H

Data of

(Hi)

1FH

CRC(Lo)

04H

0201H

(Lo)

40H

CRC(Hi)

07H

CRC(Lo)

A3H

CRC(Hi)

D4H

7-12

06H : Write Single Register

Write a word into register.
Ex : Write data (0064H) into register address 0200H and slave ADR= 01

ASCII Mode
Query PC Servo
STX

STX

ADR

(Hi)

Register

(Lo)

0
6

:
0

ADR

Function Code

ADD

Response ServoPC (OK)

Function Code

0
2

Register

ADD.

(Hi)
(Lo)

0
0

ADR

:
0
1

Function

Code

Exception

code

0
0

LRC

7
6

END1 (CR)

(0DH)

END0 (LF)

(0AH)

Write data

(word)

(word)

6
4

LRC

STX

Write data

Servo PC (ERROR)

LRC

END1 (CR)

(0DH)

END1 (CR)

(0DH)

END0 (LF)

(0AH)

END0 (LF)

(0AH)

RTU Mode
Query PC Servo

Response Servo PC (OK)

Servo PC (ERROR)

ADR

01H

ADR

01H

ADR

01H

Function Code

06H

Function Code

03H

Function Code

86H

Register
ADD

(Hi)

02H

(Lo)

00H

Register
ADD.

Exception

(Hi)

02H

(Lo)

00H

CRC(Lo)

02H

CRC(Hi)

61H

Write data

00H

Write data

00H

(word)

64H

(word)

64H

CRC(Lo)

89H

CRC(Lo)

89H

CRC(Hi)

99H

CRC(Hi)

99H

7-13

code

03H

08H : Diagnostic function

The sub-function code 0000H is able to check communication signal between Master and Slaver. Data
content is random value.
Ex: Use the diagnostic function for ID=01H

ASCII Mode
Query PC Servo
STX

STX

ADR

(HI)

Function
(Lo)

0
8
0
0
0

:
0

ADR

Function Code
Sub-

Response Servo PC (OK)

Function Code
(HI)

SubFunction

(Lo)

0
A

Code

Exception

code

0
0

LRC

7
4

END1 (CR)

(0DH)

END0 (LF)

(0AH)

(word)

(word)

0
8

Data

ADR

Function

LRC

STX

Data

Servo PC (ERROR)

7
1

LRC

END1 (CR)

(0DH)

END1 (CR)

(0DH)

END0 (LF)

(0AH)

END0 (LF)

(0AH)

RTU Mode
Query PC Servo

Response Servo PC (OK)

Servo PC (ERROR)

ADR

01H

ADR

01H

ADR

01H

Function Code

08H

Function Code

08H

Function Code

88H

Sub-

(HI)

00H

(Lo)

00H

Function

SubFunction

Exception

(HI)

00H

(Lo)

00H

CRC(Lo)

06H

CRC(Hi)

01H

Data

A5H

Data

A5H

(word)

37H

(word)

37H

CRC(Lo)

DAH

CRC(Lo)

DAH

CRC(Hi)

8DH

CRC(Hi)

8DH

7-14

code

03H

10H : Write Multipile Registers

Continuously write N words to register. * Largest number of N is 27 (1BH)
Ex.: Write data (0064H) and (012CH) into register address 100H and 101H respectively.
ASCII Mode
Query PC Servo
STX

(HI)
(Lo)

1
0

:
0

ADR

Function Code

ADD

STX

ADR

Register

Response Servo PC (OK)

Function Code

0
1

Register

ADD

(HI)
(Lo)

0
0

Code

Exception

code

0
0

END0 (LF)

(0AH)

ADD.
0100H

(Lo)
(HI)

ADD.
0101H

(Lo)

LRC

2
E
C

END1 (CR)

(0DH)

END0 (LF)

(0AH)

6
4
0
1
C
2
5
7

END1 (CR)

(0DH)

END0 (LF)

(0AH)

7-15

D
(0DH)

(word)

(HI)

END1 (CR)

LRC

(word)

(byte)

LRC

0
9

Data length

ADR

Function

Byte counters

STX

Data length

Servo PC (ERROR)

RTU Mode
Query PC Servo

Response Servo PC (OK)

Servo PC (ERROR)

ADR

01H

ADR

01H

ADR

01H

Function Code

10H

Function Code

10H

Function Code

90H

(HI)

01H

(HI)

01H

(Lo)

00H

(Lo)

00H

CRC(Lo)

CDH

CRC(Hi)

C1H

Register
ADD

Register
ADD

Data length

00H

Data length

00H

(word)

02H

(word)

02H

Byte counters

04H

CRC(Lo)

40H

Data

(HI)

00H

CRC(Hi)

34H

0100H

(Lo)

64H

Data

(HI)

01H

0101H

(Lo)

2CH

CRC(Lo)

BFH

CRC(Hi)

ADH

Exception
code

02H

LRC (ASCII Mode ) and CRC (RTU Mode) Check methods

LRC Checking:
ASCII Mode LRC (Longitudinal Redundancy Check) checking method
The LRC is calculated by adding together successive 8bit bytes of the message, discarding any carries.
Ex. add ADR, Function code, register address and data contents together, if it get the sum 19DH then discard
carrier 1 and find twos complement for 9DH to obtain LRC code.
Ex: Execute diagnostic function for Servo drive ID =01H
STX

ADR

Data (word)

Function code
(HI)
Sub-function
(Lo)

5
3
7

LRC

1
B

END1 (CR)

(0DH)

END0 (LF)

(0AH)

01H+08H+00H+00H+A5H+37H = E5H
Twos complement for E5H is 1BH ; derive LRC code: 1 , B

7-16

CRC Checking:
CRC check code is from Slave Address to end of the data. The calculation method is
illustrated as follow:
(1) Load a 16-bit register with FFFF hex (all1s). Call this the CRC register.
(2) Exclusive OR the first 8-bit byte of the message with the low-order byte of the 16-bit
CRC register, putting the result in the CRC register.
(3) Shift the CRC register one bit to the right (toward the LSB), Zero-filling the MSB,
Extract and examines the LSB.
(4) (If the LSB was 0): Repeat Steps (3) (another shift) (If the LSB was 1):
Exclusive OR the CRC register with the polynomial value A001 hex (1010 0000
0000 0001).
(5) Repeat Steps (3) and (4) until 8 shifts been performed. When this is done, a complete
8-bit byte will be processed.
(6) Repeat Steps (2) through (5) for next 8-bit byte of the message, Continue doing this
until all bytes have been processed. The final content of the CRC register is the CRC value.
Placing the CRC into the message:
When the 16-bit CRC (2 8-bit bytes) is transmitted in the message, the low-order byte
will be transmitted first, followed by the high-order byte, For example, if the CRC value
is 1241 hex, the CRC-16 (Low) put the 41h, the CRC-16 (Hi) put the 12h.
Example :
An example of a C language function performing CRC generation is shown on the following
pages. All of the possible CRC values are preloaded into two arrays, which are simply indexed
as the function increments through the message buffer. One array contains all of the 256
possible CRC values for the high byte of the 16-bit CRC field, and the other array contains all
of the values for the low byte.
Indexing the CRC in this way provides faster execution than would be achieved by calculating a
new CRC value with each new character from the message buffer.
Note
This function performs the swapping of the high/low CRC bytes internally. The bytes are
already swapped in the CRC value that is returned from the function.
Therefore the CRC value returned from the function can be directly placed into the message for
transmission.
The function takes two arguments:
unsigned char *puchMsg ;

A pointer to the message buffer containing binary data

to be used for generating the CRC

unsigned short usDataLen ;

The quantity of bytes in the message buffer.

The function returns the CRC as a type unsigned short.

7-17

CRC Generation Function

unsigned short CRC16(puchMsg, usDataLen)
unsigned char *puchMsg ;

/* message to calculate CRC upon*/

unsigned short usDataLen ;

/* quantity of bytes in message*/

{
unsigned char uchCRCHi = 0xFF ;

/* high byte of CRC initialized*/

unsigned char uchCRCLo = 0xFF ;

/* low byte of CRC initialized*/

unsigned uIndex ;
while (usDataLen--)

/* will index into CRC lookup table*/

/* pass through message buffer

{
uIndex = uchCRCHi ^ *puchMsgg++ ;

/* calculate the CRC*/

uchCRCHi = uchCRCLo ^ auchCRCHi[uIndex} ;

uchCRCLo = auchCRCLo[uIndex] ;
}
return (uchCRCHi << 8 | uchCRCLo) ;
}

High-Order Byte Table

/* Table of CRC values for high-order byte */
static unsigned char auchCRCHi[] = {
0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,
0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0,
0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01,
0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41,
0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81,
0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0,
0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01,
0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40,
0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,
0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0,
0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01,
0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41,
0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,
0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0,
0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01,
0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81, 0x40, 0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41,
0x00, 0xC1, 0x81, 0x40, 0x01, 0xC0, 0x80, 0x41, 0x01, 0xC0, 0x80, 0x41, 0x00, 0xC1, 0x81,
0x40
};

7-18

Low-Order Byte Table

/* Table of CRC values for low-order byte */
static char auchCRCLo[] = {
0x00, 0xC0, 0xC1, 0x01, 0xC3, 0x03, 0x02, 0xC2, 0xC6, 0x06, 0x07, 0xC7, 0x05, 0xC5, 0xC4,
0x04, 0xCC, 0x0C, 0x0D, 0xCD, 0x0F, 0xCF, 0xCE, 0x0E, 0x0A, 0xCA, 0xCB, 0x0B, 0xC9, 0x09,
0x08, 0xC8, 0xD8, 0x18, 0x19, 0xD9, 0x1B, 0xDB, 0xDA, 0x1A, 0x1E, 0xDE, 0xDF, 0x1F, 0xDD,
0x1D, 0x1C, 0xDC, 0x14, 0xD4, 0xD5, 0x15, 0xD7, 0x17, 0x16, 0xD6, 0xD2, 0x12, 0x13, 0xD3,
0x11, 0xD1, 0xD0, 0x10, 0xF0, 0x30, 0x31, 0xF1, 0x33, 0xF3, 0xF2, 0x32, 0x36, 0xF6, 0xF7,
0x37, 0xF5, 0x35, 0x34, 0xF4, 0x3C, 0xFC, 0xFD, 0x3D, 0xFF, 0x3F, 0x3E, 0xFE, 0xFA, 0x3A,
0x3B, 0xFB, 0x39, 0xF9, 0xF8, 0x38, 0x28, 0xE8, 0xE9, 0x29, 0xEB, 0x2B, 0x2A, 0xEA, 0xEE,
0x2E, 0x2F, 0xEF, 0x2D, 0xED, 0xEC, 0x2C, 0xE4, 0x24, 0x25, 0xE5, 0x27, 0xE7, 0xE6, 0x26,
0x22, 0xE2, 0xE3, 0x23, 0xE1, 0x21, 0x20, 0xE0, 0xA0, 0x60, 0x61, 0xA1, 0x63, 0xA3, 0xA2,
0x62, 0x66, 0xA6, 0xA7, 0x67, 0xA5, 0x65, 0x64, 0xA4, 0x6C, 0xAC, 0xAD, 0x6D, 0xAF, 0x6F,
0x6E, 0xAE, 0xAA, 0x6A, 0x6B, 0xAB, 0x69, 0xA9, 0xA8, 0x68, 0x78, 0xB8, 0xB9, 0x79, 0xBB,
0x7B, 0x7A, 0xBA, 0xBE, 0x7E, 0x7F, 0xBF, 0x7D, 0xBD, 0xBC, 0x7C, 0xB4, 0x74, 0x75, 0xB5,
0x77, 0xB7, 0xB6, 0x76, 0x72, 0xB2, 0xB3, 0x73, 0xB1, 0x71, 0x70, 0xB0, 0x50, 0x90, 0x91,
0x51, 0x93, 0x53, 0x52, 0x92, 0x96, 0x56, 0x57, 0x97, 0x55, 0x95, 0x94, 0x54, 0x9C, 0x5C,
0x5D, 0x9D, 0x5F, 0x9F, 0x9E, 0x5E, 0x5A, 0x9A, 0x9B, 0x5B, 0x99, 0x59, 0x58, 0x98, 0x88,
0x48, 0x49, 0x89, 0x4B, 0x8B, 0x8A, 0x4A, 0x4E, 0x8E, 0x8F, 0x4F, 0x8D, 0x4D, 0x4C, 0x8C,
0x44, 0x84, 0x85, 0x45, 0x87, 0x47, 0x46, 0x86, 0x82, 0x42, 0x43, 0x83, 0x41, 0x81, 0x80,
0x40
};

Exception Codes
When communication error occur , servo drive is returned with an error code and
Function code+80H return to the ModBus host controller.
Code

Name

01

ILLEGAL FUNCTION

02

ILLEGAL DATA ADD.

03

ILLEGAL DATA VALUE

04
05
06

SLAVE DEVICE
FAILURE

Description
The function code received in the query is not an allowable action
for the server (or slave).
The data address received in the query is not an allowable
address for the server (or slave).
A value contained in the query data field is not an allowable value
for server (or slave).
An unrecoverable error occurred while the server (or slave) was
attempting to perform the requested action.

RTU CHECK FAILURE RTU mode: CRC check error

ASCII CHECK
FAILURE

ASCII mode: LRC check error or no end code(CRLF)

7-19

7-2 Communication address table

All parameters allow to write data by communication excluding display parameters.
System parameters
Address

Parameter

Name of parameter

RS485

RS232

0001

510H

Cn001

Control Mode

0002

51DH

Cn002

DI Contacts function and Auto tunning

0003

511H

Cn003

Output time setting for Mechanical Brake Signal

0004

512H

Cn004

Motor rotation direction

0005

513H

Cn005

Encoder pulse output scale

0006

514H

Cn006

Reserve

0007

515H

Cn007

Value for Speed reached

0008

516H

Cn008

Brake Modes

0009

517H

Cn009

CW/CCW Drive inhibit

000A

518H

Cn010

CCW Torque command limit

000B

519H

Cn011

CW Torque command limit

000C

51AH

Cn012

Power setting for external Re-generation resistor

000D

5DEH

Cn013

Frequency of Notch Filter (Resonance Filter)

000E

5DFH

Cn014

Band Width of the Resonance Filter.

000F

58FH

Cn015

Gain selection.

0010

5F8H

Cn016

PI/P control switch Mode (Torque Command)

0011

5F9H

Cn017

PI/P control switch Mode (Speed Command)

0012

5FAH

Cn018

Switch-condition in PI/P mode (accelerate Command )

0013

5FBH

Cn019

PI/P control switch Mode (position error number)

0014

53CH

Cn020

Automatic Gain 1 & 2 switch delay time

0015

53DH

Cn021

Automatic Gain 1 & 2 switch condition (Torque command)

0016

53EH

Cn022

Automatic Gain 1 & 2 switch condition (Speed Command)

0017

53FH

Cn023

0018

540H

Cn024

Automatic Gain 1 & 2 switch condition (Position error value)

0019

587H

Cn025

Load-Inertia ratio

001A

5D0H

Cn026

Rigidity Setting

001B

58BH

Cn027

Reserve

001C

58CH

Cn028

Reserve

001D

5FDH

Cn029

Reset Parameter

001E

50BH

Cn030

Servo motor model code

001F

50EH

Cn031

Cooling fan running mode

0020

546H

Cn032

Speed feed-back smoothing filter

0021

51EH

Cn033

Speed Feed-forward smoothing filter

0022

5B8H

Cn034

Torque command smoothing filter

0023

541H

Cn035

Panel display content selection

Automatic Gain 1 & 2 switch condition (Acceleration

Command)

7-20

Address

Parameter

Name of parameter

RS485

RS232

0024

51BH

Cn036

Servo ID number

0025

544H

Cn037

Braud rate setting for (Modbus RS-485 / PC Software RS-232)

0026

545H

Cn038

Communication protocol selection

0027

567H

Cn039

Communication time-out dection time

0028

579H

Cn040

Communication response delay time

Torque control parameters

Address

Parameter

Name of parameter

RS485

RS232

0101

520H

Tn101

Linear acceleration/deceleration method selection

0102

523H

Tn102

Linear acceleration/deceleration time period

0103

521H

Tn103

Analog Torque Command Ratio

0104

522H

Tn104

Analog torque command offset

0105

526H

Tn105

Internal Speed Limit 1

0106

527H

Tn106

Internal Speed Limit 2

0107

528H

Tn107

Internal Speed Limit 3

0108

5CDH

Tn108

Torque output monitor value

Speed control parameters

Address

Parameter

Name of parameter

RS485

RS232

0201

536H

Sn201

Internal Speed Command 1

0202

537H

Sn202

Internal Speed Command 2

0203

538H

Sn203

Internal Speed Command 3

0204

529H

Sn204

Zero Speed preset selection

0205

52AH

Sn205

Speed command acceleration / deceleration methods

0206

52BH

Sn206

0207

52CH

Sn207

0208

52DH

Sn208

0209

52EH

Sn209

S curve speed command acceleration time setting

020A

52FH

Sn210

S curve speed command deceleration time setting

020B

530H

Sn211

Speed loop Gain 1

020C

531H

Sn212

Speed-loop Integral time constant 1

020D

53AH

Sn213

Speed loop Gain 2

020E

53BH

Sn214

Speed loop Integral time constant 2

020F

532H

Sn215

Value of zero speed

Speed command Smooth acceleration/deceleration-time

constant
Speed command Linear acceleration/deceleration time
constant
S curve speed command acceleration and deceleration time
setting

7-21

Address

Parameter

Name of parameter

RS485

RS232

0210

533H

Sn216

Analog Speed Command Ratio

0211

534H

Sn217

Analog Speed Command offset adjust

0212

599H

Sn218

Analog Speed Command Limit

Position control parameters

Address

Parameter

Name of parameter

RS485

RS232

0301H

550H

Pn301

0302H

560H

Pn302

Position command selection (for pulse typelogic and

drive inhizibit )
Electronic Gear Ratio Numerator 1

0303H

561H

Pn303

Electronic Gear Ratio Numerator 2

0304H

562H

Pn304

Electronic Gear Ratio Numerator 3

0305H

563H

Pn305

Electronic Gear Ratio Numerator 4

0306H

554H

Pn306

Electronic Gear Ratio Denominator

0307H

552H,553H

Pn307

Position complete value

0308H

556H,557H

Pn308

Position error band upper limit

0309H

558H,559H

Pn309

Position error band lower limit

030AH

55AH

Pn310

Position Loop Gain 1

030BH

551H

Pn311

Position Loop Gain 2

030CH

55BH

Pn312

Position Loop Feed Forward Gain

030DH

55CH

Pn313

Position command Smooth Accel/Decel time constant

030EH

55DH

Pn314

Position Command Direction definition

030FH

51FH

Pn315

Position Pulse error clear mode

0310H

50DH

Pn316

Internal Position Command Mode

0311H

568H

Pn317

Internal Position Command 1-Rotation Number

0312H

569H

Pn318

Internal Position Command 1-Pulse Number

0313H

56AH

Pn319

Internal Position Command 1-Move Speed

0314H

56BH

Pn320

Internal Position Command 2-Rotation number

0315H

56CH

Pn321

Internal Position Command 2-Pulse Number

0316H

56DH

Pn322

Internal Position Command 2-Move Speed

0317H

56EH

Pn323

Internal Position Command 3-Rotation number

0318H

56FH

Pn324

Internal Position Command 3-Pulse Number

0319H

575H

Pn325

Internal Position Command 3-Moving Speed

031AH

576H

Pn326

Internal Position Command 4-Rotation number

031BH

577H

Pn327

Internal Position Command 4-Pulse Number

031CH

578H

Pn328

Internal Position Command 4-Move Speed

031DH

59CH

Pn329

Internal Position Command 5-Rotation Number

031EH

59DH

Pn330

Internal Position Command 5-Pulse Number

7-22

Address

Parameter

Name of parameter

RS485

RS232

031FH

59EH

Pn331

Internal Position Command 5- Move Speed

0320

59FH

Pn332

Internal Position Command 6-Rotation Number

0321

5A0H

Pn333

Internal Position Command 6-Pulse Number

0322

5A1H

Pn334

Internal Position Command 6- Move Speed

0323

5A2H

Pn335

Internal Position Command 7-Rotation Number

0324

5A3H

Pn336

Internal Position Command 7-Pulse Number

0325

5A4H

Pn337

Internal Position Command 7- Move Speed

0326

5A5H

Pn338

Internal Position Command 8-Rotation Number

0327

5A6H

Pn339

Internal Position Command 8-Pulse Number

0328

5A7H

Pn340

Internal Position Command 8- Move Speed

0329

5A8H

Pn341

Internal Position Command 9-Rotation Number

032A

5A9H

Pn342

Internal Position Command 9-Pulse Number

032B

5AAH

Pn343

Internal Position Command 9- Move Speed

032C

5ABH

Pn344

Internal Position Command 10-Rotation Number

032D

5ACH

Pn345

Internal Position Command 10-Pulse Number

032E

5ADH

Pn346

Internal Position Command 10-Move Speed

032F

5AEH

Pn347

Internal Position Command 11-Rotation Number

0330

5AFH

Pn348

Internal Position Command 11-Pulse Number

0331

5B3H

Pn349

Internal Position Command 11-Move Speed

0332

5E0H

Pn350

Internal Position Command 12-Rotation Number

0333

5E1H

Pn351

Internal Position Command 12-Pulse Number

0334

5E3H

Pn352

Internal Position Command 12-Move Speed

0335

5E4H

Pn353

Internal Position Command 13-Rotation Number

0336

5E5H

Pn354

Internal Position Command 13- Pulse Number

0337

5E6H

Pn355

Internal Position Command 13- Move Speed

0338

5E7H

Pn356

Internal Position Command 14-Rotation Number

0339

5E8H

Pn357

Internal Position Command 14- Pulse Number

033A

5E9H

Pn358

Internal Position Command 14- Move Speed

033B

5EAH

Pn359

Internal Position Command 15-Rotation Number

033C

5EBH

Pn360

Internal Position Command 15- Pulse Number

033D

5ECH

Pn361

Internal Position Command 15- Move Speed

033E

5EDH

Pn362

Internal Position Command 16- Rotation Number

033F

5EEH

Pn363

Internal Position Command 16- Pulse Number

0340

5EFH

Pn364

Internal Position Command 16-Move Speed

0341

54AH

Pn365

Setting for HOME routine

0342

54BH

Pn366

1 st preset speed of HOME (high speed)

0343

54CH

Pn367

2 nd preset speed of HOME ( low speed )

0344

54DH

Pn368

HOME Position Offset. (No of Revolutions)

0345

54EH

Pn369

HOME Bias Pulse value (No of pulses)

Pn370

S-Curve Time Constant for Internal Position

command(TSL)
7-23

Address
RS485

RS232

Parameter
Pn371

Name of parameter
S-Curve Time Constant for Internal Position
command(TACC)

Quick Setup parameters

Address

Parameter

Name of parameter

RS485

RS232

0401

530H

qn401

Speed Loop Gain 1

0402

531H

qn402

Integral Time constant for Speed Loop 1

0403

53AH

qn403

Speed Loop Gain 2

0404

53BH

qn404

Integral Time constant for Speed Loop 2

0405

55AH

qn405

Position Loop Gain 1

0406

551H

qn406

Position Loop Gain 2

0407

55BH

qn407

Position Loop Feed-Forward Gain

Multi-function programmable contact parameter

Address

Parameter

Name of parameter

RS485

RS232

0501

5C0H

Hn501

DI-1 Pragrammable digital inupt

0502

5C1H

Hn502

DI-2 Pragrammable digital inupt

0503

5C2H

Hn503

DI-3 Pragrammable digital inupt

0504

5C3H

Hn504

DI-4 Pragrammable digital inupt

0505

5C4H

Hn505

DI-5 Pragrammable digital inupt

0506

5C5H

Hn506

DI-6 Pragrammable digital inupt

0507

5C6H

Hn507

DI-7 Pragrammable digital inupt

0508

5C7H

Hn508

DI-8 Pragrammable digital inupt

0509

5C8H

Hn509

DI-9 Pragrammable digital inupt

050A

5C9H

Hn510

DI-10 Pragrammable digital inupt

050B

5CAH

Hn511

DI-11 Pragrammable digital inupt

050C

5CBH

Hn512

DI-12 Pragrammable digital inupt

050D

5CCH

Hn513

DI-13 Pragrammable digital inupt

050E

5F4H

Hn514

DO-1 Pragrammable digital output

050F

5F5H

Hn515

DO-2 Pragrammable digital output

0510

5F6H

Hn516

DO-3 Pragrammable digital output

0511

5F7H

Hn517

DO-4 Pragrammable digital output

0512

5CEH

Hn518

Digital input control method selection

0513

5FFH

Hn519

Digital input status control in communication mode

7-24

Display parameters
Address

Parameter

Name of parameter

RS485

RS232

0601

6E4H

Un-01

Actual Motor Speed

0602

9B6H

Un-02

Actual Motor Torque

0603

691H

Un-03

Regenerative load rate

0604

693H

Un-04

Accumulated load rate

0605

694H

Un-05

Max load rate

0606

678H

Un-06

Speed Command

0607

65CH

Un-07

Position Error Value

0608

688H

Un-08

Position Feed-back Value

0609

632H

Un-09

ExternalVoltage Command

060A

6B7H

Un-10

(Vdc Bus) Main Loop Voltage

060B

695H

Un-11

External Spped Limit Command Value

060C

6C0H

Un-12

External CCW Torque Limit Command Value

060D

6C1H

Un-13

External CW Torque Limit Command Value

060E

8BBH

Un-14

Motor feed back Rotation value (absolute value)

060F

8BAH

Un-15

0610

8C5H

Un-16

0611

8C4H

Un-17

0612

67EH

Un-18

Pulse command rotation value(absolute value)

Pulse Command-Pulse value less than one
rotation(Absolute value)
Torque command

0613

844H

Un-19

Load inertia ratio

0614

Un-20

The status of digital output contact(Do)

0615

Un-21

The status of digital input contact(Di)

Motor feed back Less then one rotation pulse

value(absolute value)

7-25

Chapter 8 Troubleshooting
8-1 Alarm functions
The Alarm codes are displayed in a format such as that shown below. For any Alarm messages , refer to this
section for identify the cause and dispel the error. to reset the Alarm message by following pages description.
If this is not possible for any reason then contact your local supplier for assistance.

Alarm Status Display

For Alarm List refer to the section 8-2. In the example above AL-01 indicate (Under Voltage)
There is also an Alarm history which can record ten entry of alarm record.
History record is listed as alarm history record table shows.

Alarm History Record

Display
AL -
A1 -
A2 -
A3 -
A4 -
A5 -
A6 -
A7 -
A8 -
A9 -

Explanation
The Latest Alarm.
Previous First Alarm.
Previous Second. Alarm.
Previous Third Alarm.
Previous Fourth Alarm.
Previous Fifth Alarm.
Previous Sixth Alarm.
Previous Seventh Alarm.
Previous Eighth Alarm.
Previous Ninth Alarm.

Note is denotation of the Alarm Codes.

8-1

Latest record

Earliest record

Example:
Following table are procedures to access the alarm history record parameter.
Steps

Key

Turn On
the Power

LED Display

Procedures
On power on Drive Status parameter is displayed.

Press MODE key to enter the Alarm History record.

Key to view the Alarm 1 message that previously

Press
happened and the alarm code is 03 (Overload)

Key again to view Alarm 2 message and repeat

Press
this to see entire alarm history list.
In this example Alarm code is 01. (Under voltage)

Press
MODE key once to view System Parameters.
Repeat this to select all other available parameters.

8-2

8-2 Troubleshooting of Alarm and Warning

Alarm
Code

Alarm Name
and Description

Corrective Actions

Reset
Method

00

Normal

Under-voltage
01

02

03

04

The main circuit

voltage is below its
minimum specified
value. (190Vac)

Use multi-meter to check

whether the input voltage is
Turn
within the specified limit. If it can
ALRS(DI)
not be solved, there may be
ON
failure inside the Drive.

1. Use multi-meter to check

Over-voltage
(Regeneration error) whether the input voltage is
within the specified limit.
2. Check the Parameter Cn012 if
it is setting correctly.
3. If this alarm appears during
1. The main circuit
Turn
operation.
voltage is exceeded
ALRS(DI)
maximum allowable Extend ac/deceleration time
ON
or reduce load ratio in the
value. (410V)
permitted range. Otherwise,
2. Regeneration
an external regeneration
voltage is too high.
resistor is needed.
(Please contact your supplier
for assistance.)
Motor Over-load 1. Check connection for Motor
terminal s (U,V,W) and
Encoder.
The drive has
2. Adjust the Drive gain, If gain is
exceeded its rated
Turn
not correctly adjusted, it would
load during
ALRS(DI)
cause motor vibration and
continuous operation.
ON
large current will lead to motor
When the loading is
over load.
equal to 2 times of
rated loading, alarm 3. Extend acc/deceleration time
or reduce load ratio in the
occurs within 10sec.
permitted range.
Drive Over-current 1. Check connection of the motor
cable (U,V,W) and encoder.
Check power cable
connection. Refer to the
Reset
diagram in Chapter 2.
Drive main circuit
2. Turn off the power, and turn on Power
Over current or
again after 30 min. If the alarm Supply
Transistor error.
still exists, there may be
power module malfunction or
noise consider the drive for
test and repair.

8-3

Fault Status Digital Output

CN1-25 CN1-24 CN1-23 CN1-22
BB/A3
ST/A2 PC/A1
LM/A0
If there is no Alarm, CN1-22~CN1-25
operates in accordance with default
function. Please refer to 2-2-1.

Alarm
Alarm Name
Code and Description

05

06

07

08

09

Encoder ABZ
phase signal
error
Motors encoder
failure or encoder
connection
problem.
Encoder UVW
phase signal
error
Motors encoder
failure or encoder
connection
problem.
Multi-function
contact setting
error

Reset
Method

Corrective Actions

1.Check the motors encoder

connections.
2.Check the encoder if short circuit,
poor solder joints or break.
3.Check the encoder signal terminals
CN2-1 and CN2-2. ( power cable 5v)

Alarm Status Digital Output

CN1-25
BB/A3

CN1-24
ST/A2

CN1-23
PC/A1

CN1-22
LM/A0

Reset
Power
Supply

Reset
Power
Supply

1. Check parameters Hn501~Hn513,

trigger level selected by 2nd digit of
Reset
Hn 501 to 513 should be the same
Power
for all inputs DI-1~DI-13.
Input/output
2.Check parameters setting of Hn514 Supply
contacts function
~ Hn517 should NOT be the same
setting error.
for outputs contact DO-1~DO-4.
Disconnect all command cable then
Reset
Memory Error
Power
Parameter write-in re-cycle the power. If alarm still
occurs, it means the Drive was failure. Supply
error
Emergency Stop 1. Disable Emergency stop signal
input.
2. Internal mal-function.
When the input
Turn
Ensure that all connection are
contact point EMC
ALRS(DI)
correct, refer to Chapter 2 Power
is activated.
ON
and motor circuit diagrams
Alarm 09 appears.
connection.
Control wiring diagrams.
1.Check if the motor wiring U,V,W)and
encoder wiring correct or not.
2.Internal interference and
Turn
mal-function. Ensure that all
ALRS(DI)
Motor current is 4
connection are correct ,refer to
ON
times greater than Chapter 2 Power and motor circuit
rated current.
diagrams.
Motor
over-current

10

8-4

Alarm
Alarm Name
Code and Description

Reset
Method

Corrective Actions

1. Increase the position loop gain

(Pn310 and Pn311) setting value.
The deviation
2. Increase in position tolerance value
between Pulse
Turn
by (Pn307) for a better motor
command and
ALRS
response.
encoder feed back
(DI)
3. Extend the time of ac/deceleration
( position error) is
ON
or reduce load inertia in the
greater than the
permitted range.
setting of Pn308 or
4. Check if the motor wiring (U,V,W) is
Pn309.
correct.
Motor over speed 1. Reduce the speed command.
Turn
2. Electronic gear ratio is incorrect
Motors speed is
ALRS
check and set correctly.
1.5 times more
(DI)
3. Adjust speed loop gains (Sn211 &
then motors rated
ON
Sn213) for a better motor
speed.
response.
Turn off the power. Turn on again after
CPU Error
Reset
30min. If error alarm still exists, this
Power
may be due to external interference.
Control system
Refer to the chapter 2 Motor power Supply
Mal-function.
cable and control signals connections.
Drive disable
1. Remove input contact signal
CCWL or CWL.
When input
Turn
2. Check all input wiring for correct
contacts
ALRS
connections.
CCWL & CWL
(DI)
are operated at the 3. For the selected High /Low logic
ON
potential settings refer to Section
same time this
5-6-1.
alarm occurs.
Drive overheat
Turn
Over-load for a long duration will
ALRS
Power transistor
cause driver overheat, check and
(DI)
temperature
reset operation system.
ON
exceed 90C.

Alarm Status Digital Output

CN1-25
BB/A3

CN1-24
ST/A2

CN1-23
PC/A1

CN1-22
LM/A0

Position error

11

12

13

14

15

8-5

Alarm Reset Methods

1. carry out the suggestions below to reset Alarm.
(a) Reset by input signal : Once the cause of Alarm is rectified,
disable SON signal (Switch off Servo ON), then activate input signal ALRS.
Alarm condition should be cleared and the drive will be ready for operation.
Reference 5-6-1 for setting SON and Alarm signal.
(b) Reset from Keypad : Once the cause of Alarm is rectified,
disable SON signal (Switch off Servo ON), then press the buttons

and

at the same time to reset

Alarm and the drive will be ready for operation.

2. Power reset: Once the cause of Alarm is rectified, disable SON signal (Switch off Servo ON) and re-cycling
power.
Alarm condition can be reset and the drive will be ready for operation.
Waning!
1) Before applying power rest , ensure that SON is off ( SON signal is removed first) to prevent danger.
2) Ensure that the speed commands are removed before the alarm is reset, otherwise the motor may
run abruptly once the alarm signal is reset.

8-6

Chapter 9

Specifications

9-1 Specifications and Dimension for Servo Drives

Servo motor for JSDA-

Available Servo Motor

(Applicable Motor Models)
JSMA-

Servo motor capacity [KW]

Max.
Continuous output
current [A rms]
Basic Specifications

Max. output current [A

rms]
Main Circuit
Input Power
Supply

R/S/T

15A

20A

30A

50A3

75A3

100A3

150A3

200A3

300A3

SC01

SC04

SC08

MA15

MB30

MH44

MH55

MH75

MH110

SC04*1 SC08*1

TC08

MB15

MC30

HH30

HH44

HH55

MH150

TC04*1

TC04

MA10

MC15

MH30

HH75

LC03

LC08

MB10

MB20

MA05

MC10

MC20

MH05

MH10

0.4

0.8

1.0

2.0

3.0

4.4

5.5

7.5

15.0

3.5

4.4

5.16

9.5

15.0

23.0

33.2

42.1

78.0

10.5

13.2

15.5

28.5

42.0

59.8

86.3

109.5

170.0

Single/Three Phase AC

Three Phase AC 170 ~ 253V

170 ~ 253V

50 / 60Hz 5%

Main Circuit

Single Phase AC 170 ~ 253V

R/S/T

50 / 60Hz 5%

Cooling System
Control of Main Circuit
Resolution of
Encoder Feedback

Natural Air Cooling

Fan Cooling

Three-phase full-wave rectification IGBT- SVPWM Control

Incremental type: 2000ppr / 2500ppr / 8192ppr

Panel and operation key 5 digital seven-segment display ; four function key.
Control Mode

Position(Pulse input), Position (Internal control), Speed, Torque, and Dual

mode switching (Position/Speed, Speed/Torque, Position/Torque)

Internal Functions

Built-in braking
Regeneration Brake

Built-in braking transistor and resistor / External braking

resistor

transistor /
External braking
resistor

Dynamic Brake

Power-off, Servo-off, Drive prohibited and Alarm occured

Low Voltage, Over Voltage, Overload, Over Current, Encoder signal error,

Prottection Function

Muti-function contact setting error, Memory error, Emergency stop, Position

error, Motor Over Speed, CPU error, Drive disable, Overheat

Communication interface RS-232 / RS-485 (Modbus protocol)

9-1

Command Source External Pulse Control / 16-Stage internal register control

Type
Input

Pulse

Waveform
Max.
Frequency

Position
Control
Mode

Electronice Gear
Position Smoothing
Constant

Positive/Negative Edge Trigger Type : CW/CCW, CLK+DIR, A Phase + B

Phase
Line Driver (+5V), Open Collector (+5 ~ +24V)
500Kpps(Line Driver) / 200Kpps(Open Collector)
1/200 A/B 200 ( A=1~50000, B=1~50000 )
Ripple Time Constant 0~10sec

(Input Ripple Filtering)

Final Position Tolerance
(In Position)

0 ~ 50000 Pulse

Torque Limit Operation 0 ~ 100 %

Feed Forward
Compensation
Command Source

Set by Parameters
External Analog Command / 3-Stage internal Parameters

Analog
External

voltage input 0 ~ 10Vdc / 0 ~ 4500rpm (Set by Parameters)

Analog

range

Command

Input
Impedance

Speed Control Range

Speed

15000(Internal speed control) / 12000(External analog voltage control)

-0.03% or less at Load fluctuation 0 to 100% (at Rated Speed)

Control
Mode

10K

Speed fluctuation Rate

0.2% or less at power fluctuation 10% (at Rated Speed)

0.5% or less at ambient temperature fluctuation 0 to 50 (at Rated
Speed)

Accel / Decl time constant Linear: 0 ~ 50sec ; S-curve : 0 ~ 5sec ; Time constant : 0 ~ 10sec
Frequency Characteristics 400Hz (JL=JM)

Torque Limit
Zero Speed /
Speed Reach Range

Command Source
Analog

Torque

Input

Control

Signal

Mode

External analog signal / Set by Parameters

0 ~ 4500rpm (Set by Parameters)
External analog signal

Voltage Range 0 ~ 10Vdc / 0 ~ 300%

Impedance

Accel / Decel Time Constant

Speed Limit
Torque Reach Range

10K
Linear : 0 ~ 50sec
External analog signal / Set by Parameters
0 ~ 300% (Set by Parameters)
9-2

Output
Position

Type

Output

Encoder
Ratio

Phase A, B, Z Line Drive /Phase Z Open collector

Rotation Resolution 1 ~ 8192 (any arbitrary value)

Servo onAlarm resetP/PI switchingCCW/CW switch limitedExternal

Optional

DI

Input

[NPN/PNP]

To 13

Input

ports

Digital

torque limitPulse deviation clearServo lockEmergency stopSpeed

command selectionControl mode switchingPulse command inhibit
Gain switchingElectric gear ratio settingInternal pulse command
triggerInternal pulse command pauseHomingExternal reference
signalInternal position command selectionTorque/Speed command
reverseForward/Reverse operation in torque maod

Fix Output
to 4 Ports

Servo alarm codeP mode enableTorque limitDrive disableBase Block

Digital Output
[Photocoupler]

Optional
Output to
4 ports

Analog Monitor
Output

Optional
Output to
2 ports

Install Location
Environ-

Altitude

ment

Temperature

Servo readyServo alarmZero speedBrake interlockSpeed reach

Position completedHoming completedTorque reach

Speed feedbackTorque/Speed/Pulse input commandPosition

deviationvalueelectrical angleMain circuit voltage(Vdc Bus)
Indoor (avoiding direct sunshine) no erosion air (avoiding oil gases,
inflammable gas and dust)
Sea level 1000m below
o

Operating Temperature 0~ 55 C , storage Temperature: -20 ~ +85 C

Humidity

Operating, storage below 90% RH

Vibration

10 ~ 57Hz : 20m/s2 ; 57 ~ 150Hz : 2G

*1 the max. torque is up to 240% while the motor horse power is the same as the servo drive.

9-3

 Dimension for JSDA-15A/20A/30A

W (mm)
JSDA-15A/20A 69
JSDA-30A

80

Dimension for JSDA-50A3 / 75A3 / 100A3

9-4

 Dimension for JSDA-150A3

Dimension for JSDA-200A3 / 300A3

9-5

9-2 Specifications and Dimension for Servomotors

Description for Servo Motor Type Number

JSM

AP S

08

H K

TECO AC Servo

Mechanical BK :

Product Name

Without BK
BWith Brake

Motor Series :
A series

IP67
(except shaft and connector)
Motor inertia :

No.

Keyway

Oil seal

No

No

Yes

No

No

Yes

Yes

Yes

S/T : Super Low

Encoder :
B2500 ppr
H8192 ppr

L : Low
M : Middle

H : Middle
Rated Speed :
A1000 rpm
B2000 rpm
C3000 rpm
H1500 rpm

Rated Output Power :

P550 W
202 KW
01100 W 303 KW
03300 W 444.4 KW
04400 W 555.5 KW
05550 W 757.5 KW
08750 W 11011 KW
101 KW 15015 KW
151.5 KW

9-6

Input Voltage :

AAC 220V

 Standard Specifications for JSMA-PSC/PLC/TC

Motor Mode Symbol

Unit

JSMA-P
SCP5
10A

Drive Model

SC01

SC04

SC08

TC04

TC08

LC03

LC08

30A

15A

20A

10A/15A 15A/20A 20A/30A 15A/20A

Rated Output

PR

KW

0.05

0.1

0.4

0.75

0.4

0.75

0.3

0.75

Rated Torque

TR

Nm

0.16

0.32

1.27

2.39

1.27

2.39

0.95

2.39

Max. Torque

Tmax

Nm

0.48

0.95

3.82

7.16

3.78

7.16

2.86

7.16

Rated Speed

NR

rpm

Max. Speed

Nmax

rpm

Rated Current

IR

0.65

0.94

2.5

4.3

2.7

Imax

1.95

2.82

7.5

12.9

KT

Nm/A

0.356

0.380

0.510

KE

V/k rpm

40.4

39.8

JM

Kgcm2

0.029

Ra

La

3000

3000

4500

4200

5.0

2.0

3.4

8.1

15.0

6.0

10.2

0.610

0.480

0.500

0.523

0.774

61.1

63.8

50.3

52.2

54.8

81.4

0.036

0.280

0.940

0.340

1.080

0.677

2.459

71.00

25.00

5.60

2.41

5.10

1.30

5.58

2.18

mH

24.3

35.0

14.5

8.0

17.0

6.3

11.6

6.8

Tm

ms

1.43

0.59

0.50

0.58

0.72

0.54

1.32

0.85

Te

ms

0.34

1.40

2.59

3.30

3.33

4.85

2.08

3.12

Weight(Standard)

kgw

0.48

0.70

1.37

2.47

1.30

2.50

1.59

3.05

Insulation Grade

RH

Storage Temp.

Storage Humidity

RH

Max. Armature
Current
Torque Constant
Induced Voltage
Constant
Rotor Moment of
Inertia
Armature
Resistor
Armature
Inductance
Mechanical Time
Constant
Electrical Time
Constant

Operating
Ambient Temp.

4500

4200

3000

Class B (130)

5000

Class F (155)
0 ~ 40

Operating
Ambient

<80

<90

Humidity

1( kgfcm)0.0980665(Nm)

-20 ~ 60
<80

<90

1(gfcms2)0.980665(kgcm2)

9-7

 Standard Specifications for JSMA-PM

Motor Mode Symbol

Unit

JSMA-P
MA05

MA10

MA15

MH05

MH10

20A

30A

30A/50A3

20A

30A

Drive Model
Rated Output

PR

KW

0.55

1.0

1.5

0.55

1.0

Rated Torque

TR

Nm

5.25

9.55

14.32

3.50

6.40

Max. Torque

Tmax

Nm

15.76

28.65

42.96

10.51

19.21

Rated Speed

NR

rpm

1000

1500

Max. Speed

Nmax

rpm

1500

2000

Rated Current

IR

3.43

5.16

7.45

2.98

5.0

Imax

10.3

15.5

22.35

8.94

15.0

KT

Nm/A

1.679

2.039

2.110

1.293

1.411

KE

V/k rpm

175.9

213.6

221.3

135.6

147.6

JM

Kgcm2

6.26

12.14

17.92

6.26

12.14

Ra

3.58

1.85

1.19

2.31

0.95

La

mH

18.33

12.14

8.44

10.80

8.78

Tm

ms

0.76

0.52

0.46

0.83

0.55

Te

ms

5.12

6.55

7.09

4.68

9.28

Weight(Standard)

kgw

6.45

10.18

13.87

6.45

10.18

Insulation Grade

Class B (130)

0 ~ 40

RH

<90

Storage Temp.

-20 ~ 60

Storage Humidity

RH

Max. Armature
Current
Torque Constant
Induced Voltage
Constant
Rotor Moment of
Inertia
Armature Resistor
Armature
Inductance
Mechanical Time
Constant
Electrical Time
Constant

Operating
Ambient Temp.
Operating
Ambient
Humidity

1( kgfcm)0.0980665(Nm)

<90

1(gfcms )0.980665(kgcm2)
2

9-8

 Standard Specifications for JSMA-PM

Motor Mode Symbol

Unit

JSMA-P
MB10
30A

Drive Model

MB15

MB20

MB30

MC10

30A/50A3 50A3

75A3

30A

MC15

MC20

MC30

30A/50A3 50A3

75A3

Rated Output

PR

KW

1.0

1.5

2.0

3.0

1.0

1.5

2.0

3.0

Rated Torque

TR

Nm

4.78

7.16

9.55

14.33

3.20

4.78

6.37

9.55

Max. Torque

Tmax

Nm

14.33

21.49

28.65

42.96

9.60

14.33

19.11

28.65

Rated Speed

NR

rpm

2000

3000

Max. Speed

Nmax

rpm

2800

4000

Rated Current

IR

5.16

7.57

9.18

14.0

4.96

7.06

9.5

14.0

Imax

15.5

22.71

27.5

42.0

14.88

21.2

28.5

42.0

KT

Nm/A

1.019

1.060

1.140

1.130

0.715

0.740

0.740

0.750

KE

V/k rpm

106.8

108.7

119.3

118.3

74.6

77.5

77.4

78.5

JM

Kgcm2

6.26

8.88

12.14

17.92

4.60

6.26

8.88

12.14

Ra

1.22

0.79

0.58

0.33

1.02

0.65

0.40

0.25

La

mH

6.70

4.74

3.78

2.12

5.06

3.58

2.40

1.62

Tm

ms

0.70

0.61

0.52

0.45

0.88

0.71

0.62

0.51

Te

ms

5.49

6.00

6.52

6.38

4.96

5.48

6.00

6.56

Weight(Standard)

kgw

6.47

8.08

10.16

13.87

5.29

6.49

8.08

10.16

Insulation Grade

Class B (130)

0 ~ 40

RH

<90

Storage Temp.

-20 ~ 60

Storage Humidity

RH

<90

Max. Armature
Current
Torque Constant
Induced Voltage
Constant
Rotor Moment of
Inertia
Armature
Resistor
Armature
Inductance
Mechanical Time
Constant
Electrical Time
Constant

Operating
Ambient Temp.
Operating
Ambient
Humidity

1( kgfcm)0.0980665(Nm)

1(gfcms2)0.980665(kgcm2)

9-9

Standard Specifications for JSMA-PMH

Motor Mode Symbol

Unit

Drive Model

JSMA-P
MH30

MH44

MH55

MH75

MH110

MH150

75A3

100A3

150A3

200A3

300A3

300A3

Rated Output

PR

KW

3.0

4.4

5.5

7.5

11.0

15.0

Rated Torque

TR

Nm

19.1

28.0

35.1

47.8

70.1

95.5

Max. Torque

Tmax

Nm

49.5

71.5

89.6

122.6

179.0

204.0

Rated Speed

NR

rpm

1500

1500

1500

1500

1500

1500

Max. Speed

Nmax

rpm

2000

2000

2000

2000

2000

2000

Rated Current

IR

15.0

22.5

28.5

38.0

58.0

78.0

Imax

39.0

58.5

74.1

98.8

152.0

170.0

KT

Nm/A

1.27

1.24

1.23

1.26

1.21

1.22

KE

V/k rpm

81.32

82.23

81.20

81.62

83.40

83.10

JM

Kgcm2

39.99

51.44

63.52

93.94

160.94

222.20

Ra

0.18

0.12

0.09

0.05

0.03

0.02

La

mH

2.89

1.98

1.52

1.02

0.80

0.50

Tm

ms

0.69

0.60

0.56

0.49

0.48

0.37

Te

ms

16.12

16.81

17.24

18.96

26.77

29.12

Weight(Standard)

kgw

19.5

26.2

30.0

42.0

52.5

70.5

Insulation Grade

Class F (155)

0 ~ 40

RH

<90

Storage Temp.

-20 ~ 60

Storage Humidity

RH

<90

Max. Armature
Current
Torque Constant
Induced Voltage
Constant
Rotor Moment of
Inertia
Armature
Resistor
Armature
Inductance
Mechanical Time
Constant
Electrical Time
Constant

Operating
Ambient Temp.
Operating
Ambient
Humidity

1( kgfcm)0.0980665(Nm)

1(gfcms2)0.980665(kgcm2)

9-10

Standard Specifications for JSMA-PHH

Motor Mode Symbol

Unit

Drive Model

JSMA-P
HH30

HH44

HH55

HH75

100A3

150A3

200A3

300A3

Rated Output

PR

KW

3.0

4.4

5.5

7.5

Rated Torque

TR

Nm

19.1

28.0

35.1

47.8

Max. Torque

Tmax

Nm

49.5

71.4

89.6

122.6

Rated Speed

NR

rpm

1500

1500

1500

1500

Max. Speed

Nmax

rpm

3000

3000

3000

3000

Rated Current

IR

23.0

33.2

42.1

58.0

Imax

86.3

109.5

151.0

KT

Nm/A

0.84

0.83

0.82

KE

V/k rpm

54.82

53.27

53.75

JM

Kgcm2

53.02

63.52

93.94

Ra

0.08

0.05

0.04

0.02

La

mH

1.48

0.89

0.68

0.43

Tm

ms

0.70

0.62

0.56

0.51

Te

ms

18.75

16.54

17.46

18.00

Weight(Standard)

kgw

19.5

26.2

30.0

42.0

Insulation Grade

Class F (155)

0 ~ 40

RH

<90

Storage Temp.

-20 ~ 60

Storage Humidity

RH

<90

Max. Armature
Current
Torque Constant
Induced Voltage
Constant
Rotor Moment of
Inertia
Armature
Resistor
Armature
Inductance
Mechanical Time
Constant
Electrical Time
Constant

Operating
Ambient Temp.

59.8
0.83
54.21
39.99

Operating
Ambient
Humidity

1( kgfcm)0.0980665(Nm)

1(gfcms2)0.980665(kgcm2)

9-11

JSMA-PSC/PLC/TC dimension diagram

Motor Mode

Without
Brake

JSMA-PL
Series
With
Brake

LC03AB/H

5.5 100

90

76

14 70

25

20

30

113.4

LC08AB/H

6.5 112 100

86

16 80

30

25

35

148

LC08AB/H-0C 6.5 112 100 86

19 80

30

25

35

148

LC03AB/H

5.5 100

90

76

14 70

25

20

30

147.8

LC08AB/H

6.5 112 100

86

16 80

30

25

35

183.2

LC08AB/H-0C 6.5 112 100 86

19 80

30

25

35

183.2

Without

TC04AB/H

5.5 80

70

60

14 50

23

20

30

124.4

JSMA-T

Brake

TC08AB/H

6.5 105

90

80

2.5

19 70

28

25

35

135

Series

With

TC04AB/H

5.5 80

70

60

14 50

23

20

30

159

Brake

TC08AB/H

6.5 105

90

80

2.5

19 70

28

25

35

171.6

SCP5AB/H

3.5 55

48

42

30 22.5

16

2.5

25

85.8

Without

SC01AB/H

3.5 55

48

42

30 22.5

16

2.5

25

106.8

Brake

SC04AB/H

5.5

70

60

14 50

25

20

30

132.8

SC08AB/H

5.5

90

80

2.5

19 70

35

30

40

139

With

SC04AB/H

5.5

70

60

14 50

25

20

30

168.2

Brake

SC08AB/H

5.5

90

80

2.5

19 70

35

30

40

174

JSMA-PS
Series

9-12

 JSMA-PM/PH motor dimension diagram

Motor Mode

JSMA-PM
JSMA-PH
Series

Without
Brake

LZ

LA

LC

LB

LE

MA05

145

130

2.5

22

110

58

164.8 222.8

MH05

145

130

2.5

22

110

58

164.8 222.8

MA10

145

130

2.5

22

110

58

214.8 272.8

MB10

145

130

2.5

22

110

58

164.8 222.8

MC10

145

130

2.5

22

110

58

149.8 207.8

MH10

145

130

2.5

22

110

58

214.8 272.8

MA15

145

130

2.5

22

110

58

264.8 322.8

MB15

145

130

2.5

22

110

58

184.8 242.8

MC15

145

130

2.5

22

110

58

164.8 222.8

MB20

145

130

2.5

22

110

58

214.8 272.8

MC20

145

130

2.5

22

110

58

184.8 242.8

MB30

145

130

2.5

22

110

58

264.8 322.8

MC30

145

130

2.5

22

110

58

214.8 272.8

MH30

13.5

200

180

10

35

114.3

3.2

79

MH44

13.5

200

180

10

35

114.3

3.2

79

273.5 352.5

MH55

13.5

200

180

12

42

114.3

3.2

113

282.5 395.5

MH75

13.5

200

180

12

42

114.3

3.2

113

MH110

13.5

235

220

12

42

200

116

343.5 459.5

MH150

13.5

235

220

12

42

200

116

418.5 534.5

HH30

13.5

200

180

10

35

114.3

3.2

79

HH44

13.5

200

180

10

35

114.3

3.2

79

273.5 352.5

HH55

13.5

200

180

12

42

114.3

3.2

113

282.5 395.5

HH75

13.5

200

180

12

42

114.3

3.2

113

9-13

LL

245

371

245

371

324

484

324

484

Motor Mode

JSMA-PM
JSMA-PH

With
Brake

LZ

LA

LC

LB

LE

MA05

145

130

2.5

22

110

58

219.8 277.8

MH05

145

130

2.5

22

110

58

219.8 277.8

MA10

145

130

2.5

22

110

58

269.8 327.8

MB10

145

130

2.5

22

110

58

219.8 277.8

MC10

145

130

2.5

22

110

58

204.8 262.8

MH10

145

130

2.5

22

110

58

269.8 327.8

MA15

145

130

2.5

22

110

58

319.8 377.8

MB15

145

130

2.5

22

110

58

239.8 297.8

MC15

145

130

2.5

22

110

58

219.8 277.8

MB20

145

130

2.5

22

110

58

269.8 327.8

MC20

145

130

2.5

22

110

58

239.8 297.8

MB30

145

130

2.5

22

110

58

319.8 377.8

MC30

145

130

2.5

22

110

58

269.8 327.8

9-14

LL

Appendix A: Peripheral for Servo motors

App-1

App-2

App-3