Machine Tool Testing

METROLOGY LAB
QIS COLLEGE OF ENGG. & TECH.:ONGOLE,A.P.
MACHINE TOOL
ALIGNMENT TESTS
39
Machine Tool Alignment Tests
METROLOGY LAB
MACHINE TOOL TESTING

INTRODUCTION:
The surface components produced by machining processes are mostly by
generation. As a result, the quality of surface produced depends upon the
accuracy of the various movements of the machine tool concerned. It therefore
becomes important to know the capability of the machine tool by evaluating the
accuracy of the various mechanisms that are directly responsible for generating
the surface. For this purpose a large variety of tests have been designed.
MEASURING INSTRUMENTS USED FOR TESTING:
The accuracy of the machine tools employed should be higher than the
accuracy of the components that it produces. Similarly the quality of the
measuring equipment used for machine tool testing should be commensurate
with the quality expected from such testing. A few commonly used equipments
are
Dial Indicators
Test mandrels
Straight edges
Spirit levels
TEST PROCEDURES:
The major tests that are conducted on machine tool are:
Testing the quality of the slide ways and the locating surfaces
Testing the accuracy of the main spindle and its alignment with respect to
other parts of the machine tool.
Testing the accuracy of the parts produced by the machine tool.
40
METROLOGY LAB
ACCEPTANCE TESTS
LATHE MACHINE
Tests that can be conducted on Lathe machine:
1. Quality of slide ways: To test the quality of the slide ways it is necessary to
mount the dial indicator on a good datum surface. Then the plunger is moved
along the longitudinal direction of the slide ways which provides an indication
of the undulations present on the surface of the slide ways.
2. Accuracy of the spindle:
These tests are related to the true running of the spindle and the centre
located
in
the
spindle
along
with
the
alignment,
parallelism
and
perpendicularity of the spindle with the other axes of the concerned machine
tool.
True running of the centre: The live centre may be loaded into the lathe
spindle and a dial indicator mounted as shown in fig. This test is required only
for machines where the work piece is held between centres. The readings of
the dial indicator are taken while rotating the spindle through full rotation.
True running of the spindle: the taper shank of the test mandrel of about 300
mm length is mounted into the spindle as shown in fig. The plunger of the dial
indicator rests on the cylindrical surface of the mandrel. The spindle is rotated
slowly and the readings of the dial indicator are noted. The deviation should
normally be less than 0.01mm. The test is to be repeated with the dial
indicator positioned close to the spindle bore as well as at the extreme end of
the test mandrel.
41
METROLOGY LAB
Squreness of the face: this test is used to measure the squreness of the
shoulder face with reference to the spindle axis. The plunger of the dial
indicator rests on the extreme radial position of the shoulder face and the
reading is taken. It is repeated by slowly rotating the spindle till the dial
indicator comes to a point that is diametrically opposite to the reading taken
earlier.
3. Alignment tests:
Parallelism and perpendicularity: Parallelism and perpendicularity between
two axes or two surfaces is normally measured in two planes, horizontal and
vertical. For this purpose the test mandrel is mounted in the spindle as shown
in fig. with dial indicator mounted on the saddle or carriage. The plunger of
the dial indicator touches the mandrel surface as shown in fig. the saddle is
moved for a specified distance and the dial reading noted. The test is
repeated in the horizontal direction as well.
42
METROLOGY LAB
Parallelism between the outside diameter of the tail stock sleeve and the slide
ways as shown in fig.
Parallelism between the line of centres and the slide ways shown in fig.
43
METROLOGY LAB
MILLING MACHINE:
The following tests can be conducted:
1.
True running of the spindle:
2.
Spindle alignment:
In this test dial indicator is mounted on one of the surfaces whose alignment
is to be tested with another surface. In case of a horizontal milling machine
the testing of the alignment between the spindle and the over arm support
can be done as shown in fig.
44
METROLOGY LAB
The dial indicator is mounted on the spindle while a test mandrel is mounted
in the over arm support with the plunger of the dial indicator resting on the
cylindrical surface of the test mandrel. The spindle is rotated and readings are
taken when it is at different positions on the periphery of the test mandrel. The
test may be conducted at two extreme ends of the mandrel.
Parallelism between the table and the spindle axis shown in fig. A test
mandrel 300mm long is mounted in the spindle axis and the dial indicator is
mounted on the table. The reading of the dial indicator is taken at the two
extreme positions with out the table movement.
Other tests that can be conducted are:
Parallelism between the spindle axis and the transverse movement of
the table.
Perpendicularity between the spindle and the vertical column ways.
45
METROLOGY LAB
RADIAL DRILLING MACHINE:

Tests that can be conducted on Drilling Machine are:
1. True running of the spindle.
2. Perpendicularity between the spindle and the base plate.
46
METROLOGY LAB
3. Perpendicularity between the feed movement and the base plate.
47

Machine Tool Testing

Uploaded by

Copyright:

Available Formats

Machine Tool Testing

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Machine Tool Testing

Uploaded by

Copyright:

Available Formats

METROLOGY LAB

QIS COLLEGE OF ENGG. & TECH.:ONGOLE,A.P.

Machine Tool Alignment Tests

QIS COLLEGE OF ENGG. & TECH.:ONGOLE,A.P.