Lateral Torsional Buckling of Rectangular Plates in Accordance With BS EN 1993-1-1

Advisory Desk
AD 391: Lateral Torsional Buckling of rectangular

plates in accordance with BS EN 1993-1-1
BS EN 1993-1-1 does not explicitly cover LTB of rectangular plates. This
AD note provides guidance for calculating the design buckling resistance
moment ( Mb,Rd ) that can be used for BS EN 1993-1-1. To calculate Mb,Rd it is
necessary to determine the non-dimensional slenderness LT . This AD note
gives two methods of calculating LT for a plate. The first method is from first
principles, using the formula for the elastic critical moment Mcr of a plate;
the second is by using the formula for the equivalent slenderness LT of a
plate given in Appendix B, clause B.2.7 of BS 5950-1.
For BS 5950-1, AD note 310 (Staircases with flat stringers) discusses the
design of steel stairs with flat plate stringers. It suggests the design of the
stringers can be carried out by determining the buckling resistance of the
stringer over a buckling length equal to the tread spacing, assuming the
stringer is class 3.
Method 1 to determine LT :
Starting from first principles, the non-dimensional slenderness of a plate can
be determined as follows:
The standard moment for the elastic critical moment of an I section is:
Mcr = C1
2EIz
Iw
l2
Iz
2EIz
dt3
12
, IT =
dt3
3
and G =
E
2(1+)
is Poissons ratio and equals 0.3 for steel.

t and d are the thickness and depth of the plate respectively.
Therefore Mcr =
dt E
6
t2
2E
The quantity
y 1.0 2.6 ld
2E
t2
y
2E
2.8
0.667ld
t2
is denoted 1 in BS EN 1993-1-1 and is the slenderness
at which the Euler load equals the squash load.

Starting from the formula in BS 5950 -1, clause B.2.7 the equivalent
slenderness is given as:
LT = 2.8
w ld
(Equation 3)
t2
For a class 3 section, w = 2/3 = 0.667.
LT =
LT
1
2.6
(Equation 1)
(Equation 4)
For y = 275, 1 =
for y = 355,
EIzGIT
Making the substitutions Iz =

where
y 1.0 2.6 ld
LT =
Therefore for design to BS EN 1993-1-1, the non-dimensional slenderness LT

of a plate can be stated as:
l2GIT
Under uniform moment, C1 = 1.0. For a plate, there is no term involving the
warping constant IW because the section has no flanges and it is assumed
axial stresses due to warping are not developed. The formula for a plate
therefore reduces to:
Mcr =
Method 2 to determine LT :
Substituting for Mcr from equation 1 and Wel = d2t/6 into equation 2, leads to:
210000
275
= 87
1 = 76
The design buckling resistance Mb,Rd can then be calculated from clause
6.3.2.1 (3) (equation 6.55) assuming a class 3 cross-section. The reduction
factor LT is calculated from clause 6.3.2.2 (1) (equation 6.56) based on curve
d (i.e imperfection factor LT = 0.76 )
The non-dimensional slenderness LT may be determined from equation 2
or 4 above.
Assuming a class 3 cross-section, the non-dimensional slenderness is given

in BS EN 1993-1-1 (clause 6.3.2.2 (1)) by the formula:
LT =
Wel y
Mcr
(Equation 2)
Contact: Richard Henderson

Tel:
01344 636525
Email:
[email protected]
where Wel = d2t/6
New and revised codes & standards

From BSI Update September 2015
BS EN PUBLICATIONS
BS EN 10338:2015
Hot rolled and cold rolled noncoated products of multiphase steels
for cold forming. Technical delivery
conditions
No current standard is superseded.
BS EN 10346:2015
Continuously hot-dip coated steel
flat products for cold forming.
Technical delivery conditions
Supersedes BS EN 10346:2009
28
NSC
October 15
BRITISH STANDARDS UNDER

REVIEW
BS ISO 4992-1:2006
Steel castings. Ultrasonic
examination. Steel castings for
general purposes.
BS ISO 4992-2:2006
Steel castings. Ultrasonic
examination. Steel castings for
highly stressed components
NEW WORK STARTED

BS 7668
Weldable structural steels. Hot
finished structural hollow sections
in weather resistant steels.
Specification
Will supersede BS 7668:2004
EN ISO 17660-1
Welding. Welding of reinforcing
steel. Load-bearing welded joints
Will supersede
BS EN ISO 17660-1:2006
EN ISO 17660-2
Welding. Welding of reinforcing
steel. Non load-bearing welded
joints.
Will supersede
BS EN ISO 17660-2:2006
NA to EN 1993-1-4
UK National Annex to Eurocode 3.
Design of steel structures. General
rules. Supplementary rules for
stainless steels.

Lateral Torsional Buckling of Rectangular Plates in Accordance With BS EN 1993-1-1

Uploaded by

Copyright:

Available Formats

Lateral Torsional Buckling of Rectangular Plates in Accordance With BS EN 1993-1-1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lateral Torsional Buckling of Rectangular Plates in Accordance With BS EN 1993-1-1

Uploaded by

Copyright:

Available Formats

Advisory Desk

AD 391: Lateral Torsional Buckling of rectangular

is Poissons ratio and equals 0.3 for steel.

is denoted 1 in BS EN 1993-1-1 and is the slenderness

at which the Euler load equals the squash load.

For a class 3 section, w = 2/3 = 0.667.

Making the substitutions Iz =

Therefore for design to BS EN 1993-1-1, the non-dimensional slenderness LT

Assuming a class 3 cross-section, the non-dimensional slenderness is given

Contact: Richard Henderson

where Wel = d2t/6

New and revised codes & standards

BRITISH STANDARDS UNDER

NEW WORK STARTED

You might also like