Kovinyl A/F738: Physical Properties

Kovinyl
A/F738
Product
Description
A vinyl resin based antifouling paint with high content of bioactive materials providing very effective
and extended protection against fouling.
Approved as TBT-free antifouling paint by Korean Register of Shipping (KR).
Recommended Use
As a long-life antifouling paint, keel to load line, for fast or very large vessels in global trade with
extended docking intervals.
Physical Properties
Finish and Color
Drying Time
Flat. Bluish Grey (5591K), Brown (6611K), Red Brown, Dark Brown
* Bluish Gray (5591K) and Brown (6611K) color change to blue and green after a short time in service.
5 /41
20 /68
30 /86
Set to touch
8h
2h
2h
Dry through
24 h
12 h
8h
Substrate temperature
* The actual drying time is subject to the film thickness, ventilation, humidity etc., and drying time under other temperature
conditions should be checked and informed by KCC.
Solids by Volume
Approx. 42 % (Determined by ISO 3233)
Theoretical
Spreading Rate
8.4 /L in 50 dry film thickness on a smooth surface.
Specific Gravity
Approx. 1.70
Flash Point
26 /79 (Closed cup)
Application Details
Surface
Preparation
Remove any oil, grease, dirt and any other contaminants from the surface before painting by proper
method such as solvent cleaning and fresh water washing, etc.
Application
Conditions
The surface should be completely cleaned and dried. Do not apply when relative humidity is above
85 %. The surface temperature should be at least 2.7 (5 ) above dew point to prevent
condensation. In confined areas, ventilate with clean air during application to assist solvent evaporation.
Preceding Coat
Korabor Aluminum H.B. RH248, Kovinyl sealer VH137AL, Korepox H.B. EH2560 or according to
specification.
* Tar bleeding may occur from Korepotar H.B. EH173(S), etc.
This effect is only cosmetic problem and has no negative influence on the antifouling performance.
Thinning
Thinner No. 025
Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience.
However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee without
the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and you
should check that this data sheet is current prior to using the product.
KCC Corporation
Kovinyl A/F738
Application
Method
Spray (Airless or Air), Roller or Brush application.

For airless spray application ;
Nozzle orifice
: 483 ~ 584 (0.019 ~ 0.023)
Output pressure
: 13.8 MPa ~ 19.7 MPa
Fan
: 60
(Airless spray data are indicative and subject to adjustment)
Typical
Film Thickness
50 dry.
Two (2) coats are recommended in general.
Depending on the purpose and the area of use, different film thickness may be applied.
This will alter spreading rate and may influence drying time and recoating interval.
Recoating Interval
At 20 /68 , Minimum : 6 h
Maximum : Free
Before overcoating, remove any oil, salt, chalking material and any other contaminants on aged coating
film completely by proper cleaning method such as solvent cleaning and/or fresh water washing.
Shelf Life
12 months
Standard Packing
Unit
4 L, 15 L
Remarks
Avoid contact with skin and inhalation of paint mist or solvent vapor.
In case of eye contact, the eyes should be rinsed immediately by fresh water continuously for at least
15 minutes. Doctors advice is recommended.
In case of skin contact, the exposed area should be cleansed thoroughly with soap and water.
Contaminated clothing should be removed and laundered with soap and water before reuse.
In case of ingestion, swallow promptly a large quantity of milk, egg white or gelatin as a first aid.
(If
these are not available, drink a large quantity of water instead.) And obtain immediate medical
attention.
Issued
July 2011
Disclaimer : The information in this data sheet is believed to the best of our knowledge based on laboratory test and practical experience.
However, there are many factors affecting the performance of product and the product quality itself, so we are not able to guarantee without
the confirmation of the purpose of using the product from us in writing. We reserve the right to change the data without notice and you
should check that this data sheet is current prior to using the product.
KCC Corporation

Kovinyl A/F738: Physical Properties

Uploaded by

Copyright:

Available Formats

Kovinyl A/F738: Physical Properties

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kovinyl A/F738: Physical Properties

Uploaded by

Copyright:

Available Formats

Kovinyl

Approx. 42 % (Determined by ISO 3233)

8.4 /L in 50 dry film thickness on a smooth surface.

26 /79 (Closed cup)

Thinner No. 025

Spray (Airless or Air), Roller or Brush application.

You might also like