Subject:: TKC Mms 8 Round Ancillary Specifications

SECTION
TKC MMS 8 ROUND

ANCILLARY
SPECIFICATIONS
GTF
05/15/08
Engineer
RJH
05/15/08
Dir Engr
DR
05/16/08
GM QA
GTF
05/15/08
REVISION
SUBJECT:
Prepared By
001
05/14/08
VISUAL THREAD INSPECTION
1.0
SCOPE
1.1
This document sets forth the broad guidelines for the field visual thread inspection of TKC MMS 8 ROUND connections by independent inspection agencies.
2.0
DEFINITION
2.1
Visual thread inspection shall be defined as those inspections that may be performed on TKC MMS
- 8 ROUND connections without the use of thread element gages.
3.0
PIN/FIELD END INSPECTION

3.1
Pin Face
3.1.1
Visually inspect the pin face for surface irregularities. Minor dents or dings to the pin face
are detrimental to the connection, however, most can be repaired by lightly filing if they do
not exceed 50% of the face width. Dents or dings on new connections that are sufficiently
deep to cause a raised area or protrusion on the pin face surface are rejectable. The repair
of such conditions during the running of the connection is at the discretion of Huntings
service representative.
3.1.2
The pin face, ID chamfer and OD chamfer are to be smooth and free from burrs.
3.1.3
Visually inspect the OD and ID chamfers to assure they consist of the proper radius.
3.1.4
Visually inspect the internal coating condition in the connection area.
4.0
3.2
Threaded Area
3.2.1
Visually inspect for full form thread length. The full form thread length is measured from
the thread start point axially along the thread crests. The connections are required to have
full form threads for the appropriate distance as specified by API 5B Table 2.3 and 2.6
(Lc).
3.3
Make-up Length
3.3.1
Visually inspect each connector for the presence of visual make-up.
3.3.2
The make-up length may be measured with a vernier dial caliper capable of measuring in
0.001" increments. The make-up length is provided in each of Hunting product brochures
under the heading of Make-up loss.
COUPLING/MILL END INSPECTION

4.1
Mill Make-up
4.1.1
Visually inspect the powertight connection for indications of proper make-up. The
coupling face should be circumfrentially parallel to the tube make-up marks and the
coupling mark within the two marks on the tube.
4.1.2
Visually inspect the made-up pin face on the coupling seal ring to ensure it is properly
seated into the seal ring with no bulges, tears or flat spots present.
4.2
Threaded Area
4.2.1
Visually inspect the full form threaded area for damage. Small areas of impact damage or
galls occurring during hydrotest must be repaired. Field repairable thread damage on new
connectors shall not exceed 0.125" in circumferential length or 0.004" in depth. All
repaired areas should be covered with an anti-gall and anti-corrosion compound such as
Moly-Kote.
4.2.2
Allowable corrosion pitting in the full form thread area shall be as defined in the
DEFINITION OF TERMS under Minor Pitting.
h:\degeorge\myfiles\publisher\tkc mms8rd\visual-00
Page 1 of 2 Pages
SECTION
TKC MMS 8 ROUND

ANCILLARY
SPECIFICATIONS
GTF
05/15/08
Engineer
RJH
05/15/08
Dir Engr
DR
05/16/08
GM QA
GTF
05/15/08
REVISION
SUBJECT:
Prepared By
001
05/14/08
VISUAL THREAD INSPECTION
4.3
Coupling Face
4.3.1
Visually inspect the coupling face and OD chamfer for impact damage. Impact damage
that has caused the starting thread crest to be indented sufficiently to cause interference
with the pin connector thread root on make-up is cause for rejection.
4.4
Coupling Seal Ring

4.4.1
The coupling should include a teflon seal ring. Visually inspect the seal ring to insure it is
properly seated in the seal ring groove. If any portion of the seal ring is cut away or torn, it
must be disgarded and a new one installed in accordance with the TKC MMS 8 ROUND
SEAL-RING INSTALLATION PROCEDURE.
5.0
CONNECTION GAGING
5.1
The gaging of Huntings proprietary connections shall only be performed by a Hunting Quality
Assurance or Service Representative or an approved Licensee. Hunting personnel or Licensee are
the only persons that have availability to the proprietary gages to which the products are
manufactured.
6.0
THREAD/STORAGE COMPOUND
6.1
Upon completion of visual thread inspection verify appropriate thread or storage compound is being
applied to both ends of the tube. The approved thread/storage compound shall be as stated in the
applicable "FIELD RUNNING AND HANDLING PROCEDURE".
NOTE: Notify Hunting Northpoint, Houston, Texas, Quality Assurance Department
immediately if thread/storage compound being applied is not listed in the applicable
"FIELD RUNNING AND HANDLING PROCEDURE".
7.0
REJECTION
7.1
Any thread that does not meet the specified requirements, shall be considered a reject.
7.2
All rejects shall have the entire thread area painted red.
7.3
All rejects shall be clearly identified as reject to protect against out-of-tolerance material being
shipped as prime material.
7.4
Rejection may be reworked by removing the defective condition and re-threading the parts within
the appropriate tolerances.
7.5
Any discrepancies shall be clarified and dispositioned by Huntings Q.A. Department before any
further processing or delivery.
h:\degeorge\myfiles\publisher\tkc mms8rd\visual-001
Page 2 of 2 Pages

Subject:: TKC Mms 8 Round Ancillary Specifications

Uploaded by

Copyright:

Available Formats

Subject:: TKC Mms 8 Round Ancillary Specifications

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Subject:: TKC Mms 8 Round Ancillary Specifications

Uploaded by

Copyright:

Available Formats

SECTION

TKC MMS 8 ROUND

VISUAL THREAD INSPECTION

PIN/FIELD END INSPECTION

COUPLING/MILL END INSPECTION

TKC MMS 8 ROUND

VISUAL THREAD INSPECTION

Coupling Seal Ring

You might also like