Earn

3 CE credits
This course was
written for dentists,
dental hygienists,
and assistants.

Anatomy of a Handpiece:
Understanding Handpiece
Maintenance and Repairs
A Peer-Reviewed Publication
Written by Glenn Williams, BS

Publication date: December 2010

Expiry date: November 2013

Go Green, Go Online to take your course

This course has been made possible through an unrestricted educational grant. The cost of this CE course is $59.00 for 3 CE credits.
Cancellation/Refund Policy: Any participant who is not 100% satisfied with this course can request a full refund by contacting PennWell in writing.

Educational Objectives
The overall goal of this article is to provide the reader with
information on current air-driven and electric handpieces.
Upon completion of this course the reader will be able to do
the following:
1. List and describe the major components of air-driven
high-speed handpieces and electric handpieces
2. List and describe the main differences between air-driven
high-speed handpieces and electric handpieces
3. List and describe the signs of failure for air-driven and
electric handpieces
4. List and describe the maintenance steps for air-driven
handpieces
5. List and describe the options for repair/rebuild of airdriven handpieces and considerations in selecting one.

Abstract
Todays clinician is extremely dependent on the handpiece to
sustain a smooth-running practice. The handpiece is an incredibly sophisticated device that requires a diligent maintenance protocol to keep it running properly and safely; routine,
repeated heat sterilization has the most adverse effect on the
dental handpiece. Perhaps due to this dependency on handpieces, combined with the damage resulting from repeated
routine sterilization and the need for consistent maintenance,
the handpiece has earned an undeserved reputation for excessive breakdowns. The dental team can keep handpieces
functioning smoothly longer, and maximize the return on
the significant investment the dentist has made in handpiece
technology, through appropriate maintenance procedures.
Careful selection from repair options is also required.

Introduction
The dental handpiece of today is a sophisticated combination of precision parts moving in perfect synchronization at
extremely high speed. This combination delivers a smooth,
powerful cut that allows the clinician to remove tooth structure in an efficient manner with as little discomfort to the
patient as possible. In contrast, up until the 1950s all dentistry
was performed with electric belt-driven instruments with top
rotational speeds of 50,000 rpm. This relatively slow speed
increased the time spent on tooth preparation and was also extremely uncomfortable for the patient, who experienced much
pressure and vibration. The belts that ran the handpieces were
heavy and restrictive and tangled with any nearby hair. The
leap from belt-driven to air-driven handpieces in the United
States was made by Dr. John Borden during the 1950s, and
pioneering work for the air-driven high-speed handpiece was
performed by Sir John Walsh in New Zealand.1,2
Figure 1. First-generation air-driven high-speed handpiece

This new technology paved the way for higher cutting

speeds, which dramatically reduced the time involved in
preparing teeth for restorative treatment. As the air turbine
handpiece evolved, other problems such as increased concentricity were solved. This resulted in a smoother cut with
better margins and less vibration transferred to the patient,
and water spray was introduced to cool the tooth surface
due to the heat generated from the much higher speeds.
Dentistry was revolutionized starting in the early 1970s
as traditional treatment methodology gave way to more
modern methods of delivering treatment in an environment
that was more comfortable for both the patient and dentist.
Sit-down dentistry and four-handed dentistry were
introduced, along with reclining patient chairs and multiple
simultaneous patient appointments. Most of what we now
take for granted as restorative dentistry was made possible because of the advancing technology of the air-driven
handpiece.
Figure 2. Air-driven low-speed handpiece circa 1968

Evolving Handpiece Technology

As more manufacturers entered the marketplace throughout
the 1980s, the handpiece industry evolved. New features were
introduced, including the placement of optic fibers through
the handpiece to deliver light directly to the cutting area at
the tip of the bur. Various automatic chucking mechanisms
were also developed in an effort to speed up the changing of
burs, and with the advent of the autochuck, the need to
use two high-speed handpieces at once (so that the assistant
could change the cutting instrument while the dentist was
working with a different bur) was eliminated. Most clinicians
now change their own burs effortlessly in seconds. The next
improvement came in the form of a swivel connector incorporated into the design of the handpiece to reduce the amount of
tubing torque. Tubing torque is defined as the resistance
or drag the operator feels from the weight of the tubing
transferred through the handpiece, and creates a tendency
for the handpiece to resist rotating in the operators hand or
to spring back after being rotated during a procedure. Most
swivels were designed as quick disconnects, which facilitated
the removal of the handpiece for daily lubrication.
www.ineedce.com

At this point, handpieces required oil only once daily

and average turbine life was measured in years. This soon
changed with the increased awareness of infectious diseases,
including the relatively new disease known as AIDS. Debate ensued over proper infection control protocols within
the dental treatment room. On May 20, 1992, millions of
Americans sat watching their televisions, not knowing that
dentistry and the handpiece industry were about to change
virtually overnight. That evening, CBS Street Stories
and NBC Dateline aired controversial stories about the
lack of handpiece sterilization in the dental practice. This
night marked a turning point and changed forever the
way handpieces are purchased, used, and maintained. In
1992 a report was published, based on laboratory studies,
recommending routine heat-treatment of handpieces.3
Shortly prior to this, a tragic event had made headlines:
a young woman in Florida, Kimberly Bergalis, became
infected with the AIDS virus under highly questionable
circumstances.4 News media sources were quick to associate this tragedy with the young womans dentist. Televised
congressional hearings in 1993 focused national attention
on the dental industry, and soon after this the FDA issued
the first guidelines mandating routine handpiece sterilization for private dental practices.5,6 The handpiece was soon
to become one of the most troublesome workhorses in the
dental office, placing increasing demands on staff time and
increasing handpiece costs, which until then had been a
minimal overhead expense.

Criteria for Selecting Air-Driven High-Speed

Handpieces for Clinical Use
Investing in a handpiece system can quickly add up to
become a significant capital expense, and there are also the
long-term operational costs of handpiece maintenance to
consider. Therefore, the clinician should apply careful consideration to the features, reliability, and maintenance requirements of a particular handpiece model when evaluating
different brands for a purchase decision. To complicate the
process, FDA regulations prohibit handpiece manufacturers from accepting opened product back from customers not
satisfied with their purchases. For this reason, the purchaser
should request a demonstration handpiece be supplied so
that it can be incorporated into the practice for some period
of time under real-life operating conditions before making
a final decision. The following list of possible criteria to be
considered may serve as a useful guide when selecting a new
handpiece system.
Head Size and Angulation: Historically there has been
a natural trade-off between head size and cutting power.
Most manufacturers offer different models featuring a large
and a small head design. A small head size improves visibility and access, especially in the posterior region, while larger
head sizes incorporate a larger turbine impeller with more
inertial mass that can yield higher power output. More cutwww.ineedce.com

ting power equals less time involved in tooth preparation.

Head angulation is another feature that some manufacturers
have taken steps to improve. The typical handpiece head is
angled back at 22.5 degrees so that the cutting instrument
remains in line with the operators line of sight, however this
can sometimes restrict access to posterior teeth by causing
the handpiece to come in contact with the maxillary arch.
Newer designs feature a unique head angle to increase posterior access and patient comfort.
Figure 3. Handpiece head sizes
8.5 mm

10.2 mm
11.9mm

9.8 mm
Stylus ATC 990

Stylus ATC 990

13.0 mm
14.5mm
Stylus ATC 890
Stylus ATC 890

Sound Level: Dental professionals are at risk for hearing

loss from the long-term effects of proximity to high-speed
handpiece noise over a career. Elevated handpiece noise levels can also cause patient discomfort and increased anxiety.
In recent years, newer handpiece models with lower noise
levels have become available, operating in a range of 58 to
71 decibels (dB).
Ergonomic Design: The minutes the clinician spends
holding a handpiece constitute a significant portion of an
eight-hour treatment day, and over the course of a career,
long-term health issues can manifest in the form of carpal tunnel syndrome, resulting from holding a heavy or
awkward handpiece. Different handpiece models can vary
significantly in length, weight, and balance. A good way to
determine the best fit and feel for your hand is to actually use
the handpiece in your practice, not while standing in a booth
at a dental meeting.
One recent trend in handpiece design is a wider, flared
body shape toward the rear of the handpiece, which reduces
the pinching force required to grip the handpiece, thereby
reducing hand and wrist fatigue. The addition of a fully
rotating swivel connecting the handpiece to the delivery
tubing significantly reduces the tubing torque felt by
the operator. Without a swivel, the operator is fighting this
constant resistance throughout the day, which can lead to
fatigue and injury over time.
3

Figure 4. Air-driven high-speed handpieces

and produce a very quiet hum as opposed to the highpitched whine of an air-driven high-speed handpiece. Fiber
optics and multiport water spray are delivered through the
attachments.7
Figure 5. Electric handpiece unit and attachment examples

Water Delivery: All high-speed handpieces incorporate

a water spray as a coolant; the latest innovation is a multiport
spray emanating from the face of the handpiece. This provides
even distribution of coolant water over the entire surface of
the tooth and prevents the water spray from being blocked
when cutting is performed on the distal surface of a tooth.
Fiber Optics: Fiber optics enhance operator visibility.
Cellular optics have been introduced that are made from one
solid glass rod instead of a collection of optic fibers. The newest innovation in optics is an LED lightbulb that generates a
brighter, whiter light. Most existing systems are retrofittable
to an LED lightbulb.
Autoclavability: Handpiece manufacturers are constantly seeking improvement in their handpiece designs to
better withstand the harmful effects of the autoclave. Materials from bearing retainers to O-rings have evolved through
several generations to higher-temperature heat-resistant
components. New materials such as titanium are used for
the handpiece body or shell, or special coatings are applied to
help preserve the handpieces external finish.

Electric Handpieces
The single biggest difference in comparing an electric
handpiece to an air-driven handpiece is its constant speed.
With an electric handpiece, there is no difference between
free-running speed and active speed, due to the amount of
power generated by the electric motor driving the handpiece, and no power is lost while cutting tooth structure.
Another advantage of the new electric handpieces is that
they are significantly quieter than air-driven handpieces.
An electric handpiece consists of an entire system. A control
box must be mounted on the delivery unit, and a conventional delivery tubing plugs into the box, which provides
signal air and water, enabling the motor to be operated from
the foot control already in use. The control box has digital
settings so the operator can literally dial in the exact speed
at which he or she would like the bur to rotate. Lightweight
tubing extends from the control box to the motor. Electric
motors look and feel like cylindrical low-speed air motors
4

Any number of attachments with various gearing combinations will connect onto an electric motor. The most
commonly used attachment for operative dentistry is a 1:5
step-up referred to as a high speed attachment. Most
electric motors operate at 40,000 rpm; adding a 1:5 speedincreasing attachment provides 200,000 rpm at the bur.
This speed remains constant no matter how aggressively
the clinician is cutting, and the advantage is much faster
preparation time. There is a learning curve associated with
mastering this increased power. Electric attachments are
generally universal, meaning that any brand will work with
any motor. One exception is the new Comfort Drive by
Kavo, a more compact design.
There are a few trade-offs to be aware of with electric
handpieces. Together, the attachment and the motor are
similar to working with a low-speed handpiece in your
hand, versus the shorter and lighter high-speed air-driven
devices. This may be of particular concern to operators with
a smaller hand size. On the other hand, many users report
that since the actual cutting time is reduced, this offsets any
limitations based on size and weight. Electric handpieces
have been found to be more efficient than air-driven highspeed handpieces.8 Head size is also typically larger than
with the average high-speed air-driven handpiece. A major
investment is associated with equipping an office with
electric technology, with the cost for a complete system
beginning at around $3,500, and there are additional costs
for each attachment required for sterilization redundancy.
Electric handpieces consist of several complex parts the
attachment is more similar to a gear-driven low-speed than
to an air-driven high-speed handpiece. A series of drive
shafts and transmissions increase the rpm of the handpiece
from 40,000 where it connects to the motor up to 200,000
in the head. This intricate array of gears and bearings
makes repair more costly than for air-driven high-speed
handpieces.
www.ineedce.com

Figure 6. Internal working of an electric handpiece

Unlike an air-driven handpiece, which loses torque as the turbine components wear, the electric motor is so powerful that it
will continue to drive the attachment as internal parts fail. Even
after bearings or gears disintegrate, the motor will continue to
operate the handpiece, and this increased friction leads to heat
that can burn a patient. On September 23, 2010, the FDA issued a second safety alert regarding reports of serious patient
tissue damage due to overheated electric attachments during
dental treatment procedures.9 The operator must be aware of
any sensation of heat in the handpiece or the head. It is imperative that you stop using an electric handpiece immediately if
you feel any heat during use. This simple precaution will, most
importantly, prevent patient injury and will also reduce the
cost of repair by not causing further damage to internal parts.

A Hybrid Air-Electric Handpiece

The latest evolution in handpiece design is the Stylus ATC
by Midwest. This system resembles an electric installation
but is referred to as a hybrid, using both air pressure and
electricity. ATC refers to Adaptive Torque Control and
uses a sensor in the handpiece tubing to operate a valve that
continuously regulates the amount of air pressure flowing to
the turbine. Instead of the handpiece losing power and freerunning speed when the bur contacts the tooth, the valve
opens, sending more pressure to the turbine to compensate.
This constant active speed delivers the same torque curve
as an electric handpiece does. The benefit to the clinician is
a handpiece with the power of an electric handpiece but size
and weight characteristics similar to those of a high-speed airdriven handpiece.
Figure 7. Torque control unit

Routine Sterilization of Handpieces

Prior to the 1990s, dental handpiece sterilization was not an
issue, and while handpiece manufacturers maintained that
handpieces were autoclavable, there was little practical call
for testing those claims. However, once clinicians began to
sterilize handpieces between patients, they began to experience a variety of performance problems. Handpiece life
expectancy dropped dramatically due to the stresses of repeated sterilization, and handpieces required substantially
more service and repair. Rather than lasting for several
years and requiring little if any maintenance, handpieces
now showed signs of extreme wear within a year or less.
How long does a handpiece turbine last? This is perhaps the
most frequently asked question related to handpiece purchase and repair. It is difficult to quantify life expectancy
under sterilization conditions because of the tremendous
number of variables associated with turbine life: lubrication, type of sterilizer, conditions of use, number of use/
sterilization cycles per day, and maintenance practices of
the individual office.
Two noteworthy independent studies devoted to quantifying handpiece longevity under continued sterilization
have been published. The United States Air Force Dental
Investigative Service (DIS) at Brooks Air Force Base is responsible for dental product evaluation for all branches of
the military and in 1993 conducted an extensive study to determine the life expectancy of a handpiece subjected to ongoing use and sterilization. DIS measured ten performance
parameters on nine different handpiece models subjected to
1,000 use/sterilization cycles. Each handpiece was properly
maintained and subjected to simulated clinical use prior to
every sterilization cycle. DIS concluded that the clinician
can expect a handpiece to survive approximately 500 sterilization cycles without significantly reduced performance,
if the handpiece is properly maintained.10 In October 2000,
Clinical Research Associates (CRA) published very similar
results from a long-term study performed with four different models of handpieces. CRA concluded that with proper
maintenance the handpiece models tested should achieve at
least 539 use/sterilization cycles before failure. Five hundred cycles for a handpiece used and sterilized twice a day,
five days per week, would translate into approximately one
year of clinical service.11

Air-Driven Handpiece Component Parts and

the Impact of Sterilization
Understanding handpiece components and how they work
and learning how to maintain them properly can help
clinicians reduce expense and realize long, dependable
service from their handpieces. An air-driven high-speed
handpiece consists of two main components: the body, or
shell, through which air and water are delivered, and the
turbine. Each element is affected differently by repeated
heat sterilization.
www.ineedce.com

Body or Shell
Brass is the most common material used in handpiece
manufacturing; it is a relatively inexpensive material and
easy to machine, although it is soft and susceptible to denting. Cosmetic protective plating is applied over the brass
but can discolor or flake off over time as a result of sterilization. Stainless steel is another material commonly used to
make handpiece bodies. Steel is lighter and stronger than
brass, but its use results in higher manufacturing costs, so
the prices are generally higher. The current state-of-the-art
in handpiece construction is titanium, which is 40 percent
lighter than stainless steel and stronger and more resistant
to the corrosive effects of autoclaving.

The Air-Driven High-Speed Handpiece Turbine

The component that fails most often on a high-speed air-driven handpiece is the turbine; as this degrades, the handpiece
exhibits signs of impending failure that are all too familiar to
the dental team.

Figure 8. Body or shell

Figure 10. High-speed turbine Figure 11. Effects of wear and

sterilization

Figure 9. Corrosive
effects of sterilization

The body shell of most handpieces comprises two parts: the

head that houses the turbine and an outer sheath. Problems
have been experienced with the heads separating from the
outer shell as a result of heat processing, and various methods have been employed in the past to join these two parts
together. However, the joint is a weak area, and further stress
is introduced with pushbutton-type bur changing. The joint
between the head and body can loosen, and the head can
become too dented and affect the turbine operation.
Older-generation handpieces contain bundles of tiny lighttransmitting glass fibers held together with adhesive; these
bundle optics degrade and darken over time with repeated
sterilization. Most new handpiece models employ cellular, or
fused-rod, optics. Manufacturers claim that virtually no degradation occurs with cellular optics and back their claims with
a five-year warranty. However, cellular optics are more fragile
and will not survive a severe drop without fracturing.
Air and water are delivered through the body to the handpiece head. This includes drive air (used to rotate the turbine),
coolant water, and chip air (often used to atomize the water
spray). After the drive air is passed through the turbine, it
is exhausted through the hollow body of the handpiece and
down the handpiece tubing. A major problem associated with
handpiece sterilization is the continual buildup of rust and
corrosion that naturally occur in the steam-saturated environment of the autoclave. One way internal corrosive buildup
negatively impacts handpiece performance is a gradual closing off of the handpiece exhaust ports, leading to increased
backpressure around the turbine. This results in loss of turbine speed and power. Air and water lines are more prone to
clogging as a result of sedimentary buildup in the recirculated
6

water of older sterilizer models utilizing a reservoir. Newer

sterilizer designs provide a fresh charge of distilled water for
every steam cycle, greatly reducing the susceptibility to clogging. The latest handpiece models feature a multi-port water
spray that disperses water evenly around the work area. These
systems, however, incorporate tiny O-rings that break down
with repeated sterilization.

Turbines rotate at speeds ranging from 380,000 to 450,000

rpm, faster than anything else on the planet. Turbine speed
can be categorized as free speed and active speed.12 Free
speed is the maximum rpm with no load. Active speed is
the actual speed the turbine is reduced to when the cutting
instrument engages the tooth structure. Most high-speed
handpieces have an active speed in the range of 180,000 to
200,000 rpm. This extremely high speed allows the clinician
to cut through hardened tooth structure with ease, leaving
a smooth, clean margin, with reduced trauma to the surrounding structure and tissue. As the turbine bearings wear,
speed decreases. Clinically, this results in longer preparation
times with slower cutting and rougher margins. Power, also
referred to as torque, is the measure of the handpieces
ability to remove tooth structure and is expressed as watts
of energy, while torque is measured in oz/inch. Handpieces
used to generate 10 to 13 watts, while newer handpiece
models produce 15 to 18 watts and have smaller head sizes.
The greater the power available to operate the cutting instrument, the less physical demand is placed on the operators hand and wrist, which means less fatigue and reduced
risk of long-term injury.
Concentricity can be defined as the ability of the handpiece to produce a cutline consistent with the diameter of
the bur. The more concentrically a handpiece operates, the
smoother the bur cuts, with less perceptible vibration and
greater comfort for the patient. The International Standards
www.ineedce.com

Organization (ISO) specifications13 allow up to 0.03 mm

of eccentricity, commonly referred to as run out or bur
wobble. Concentricity one of the most critical features of
handpiece performance diminishes as the turbine deteriorates, and a pronounced lack of concentricity can be visible
to the eye. Bur retention is another critical feature of todays
automatic chucking mechanisms. Sterilization affects autochucks in different ways. Autoclaving causes accelerated
chuck failure when heat causes the springs that provide gripping force to lose their temper and strength, while corrosion
dulls the sharp edges used to grip bur shanks. Clinically,
autochuck failure is manifested as the bur working out of the
chuck during use, which creates a very dangerous situation.
In spite of significant technological advancements in
handpiece design over the last ten years, dental professionals
continue to experience recurring handpiece problems resulting from sterilization. Misconceptions abound throughout
the dental field about exactly what goes wrong when a handpiece turbine fails. Closer examination of the turbine may
shed light on just what is happening inside your handpiece.

These miniature bearings are the heart of the turbine. As

reported in the 1993 DIS study, handpieces do not fail
gradually because of decreased speed and power but, rather,
fail as a result of catastrophic failure of the turbine bearings.
The most critical element of these bearings is the retainer, or
cage, that secures the ball bearings within the raceways. This
becomes brittle as it is subjected to harsh sterilization environments; upon failure, the bearing cage disintegrates and the
turbine will no longer rotate or generate power. You will most
often see evidence of this final degradation when black stuff
is expelled from the handpiece head during use or lubrication
procedures. The dentist may also note that the bur will stall
out when applied to tooth structure. Other symptoms of
bearing failure include the bur no longer spinning concentrically, unacceptable vibration when the handpiece is activated,
or unusually loud sounds emanating from the turbine.14
Figure 14. Bearing retainer showing stages of degradation

The Handpiece Turbine Assembly

As the only moving part inside a high-speed handpiece, the
turbine is the most common source of problems. A highspeed turbine contains two components: a chucking mechanism to hold the cutting instrument and a rotary system that
spins the bur at speeds up to 6,000 times per second when air
pressure is supplied.
Figure 12. Handpiece turbine assembly

The rotary system consists of an impeller, or rotor, which

catches drive air (similar to a water wheel), mounted on a
spindle. The spindle rotates clockwise at high speeds, supported by two precision bearings and two suspension O-rings.
Figure 13. High-speed air-driven turbine components

1.
2.
3.
4.
5.
6.
7.
www.ineedce.com

Spindle
Chuck
Rear bearing
Impeller
Front bearing
End cap
O-rings

Improved cage materials and manufacturing processes have

extended handpiece life since the advent of routine sterilization, as evidenced by the longer warranties prevalent today.
Other design improvements offer the clinician the choice of
maintenance-free (lube-free) handpieces. This is accomplished by saturating the bearing cage with a food-grade,
autoclavable grease that gradually releases onto the ball bearings over time through use and sterilization. The bearings are
not really lubrication free. They are maintenance free,
however, as it is no longer necessary for the staff to apply
lubricant. One of the latest innovations in dental bearing applications is a bearing cage coated with a layer of pure silver.
According to a leading bearing manufacturer, the new silver
composite retainers combine the lubricating capabilities
of metallic silver with strength and the ability to withstand
repetitive autoclave cycles.

Prolonging Handpiece Life Through Proper

Use and Maintenance
Much can be done to prolong handpiece life by understanding the importance of variables that can be controlled
within the practice and by understanding and adhering to
some basic handpiece maintenance.
Proper Air Supply
One of the most frequent causes of premature bearing failure is excessive air pressure entering the handpiece. Every
handpiece head has a specific capacity for exhausting air.
Additional air tends to accumulate around the turbine and
may reduce speed. An accurate reading for handpiece air
pressure can be obtained only by using an in-line air gauge
7

to measure air pressure directly at the handpiece connection (the air pressure gauge on the front of the dental unit is
little more than a relative indicator and does not account for
frictional air loss through the tubing). Some manufacturers
incorporate a valve inside the handpiece that regulates incoming air to prevent excessive pressure from reaching the
turbine. The quality of the drive air can also impact turbine
life. Oil and condensation accumulate in the compressor
tank during normal operation, and without proper drying or
filtration, oil and water may travel through the air lines to the
handpiece tubing. These particles then impact the delicate
turbine at high speed, like marbles tossed against a spinning fan. You can easily check drive air quality by aiming
an empty hose at a mirror or facial tissue. Any water or oil
will show up as moisture or discoloration on the surface. If
you have doubts about your air quality or pressure, contact a
service technician to inspect dryers, filters, and connections
and drain the compressor tank.
Cutting Instruments
The cutting instrument itself can have an impact on turbine life. Overusing dull burs may cause the operator to
exert more lateral force against the tooth structure, thereby
increasing the side load on the bearings and resulting in
excessive friction while operating the handpiece. Using a
surgical-length bur, or simulating one by extending the bur
from the chuck a few millimeters, can significantly affect the
load on the turbine. The longer the cutting instrument, the
greater the negative impact on concentricity. Burs should
be seated fully into an autochuck and never extended. Conversely, short-shanked burs should never be inserted into
a chuck past the taper on the shank. Inferior-quality burs
with variable shank diameters overextend the springs in autochucks, leading to premature failure. It may seem obvious
the nature of the dental practice can also have an impact
on turbine life. A high-volume crown and bridge practice
cannot hope to achieve the same life span from a handpiece
as can a pediatric dentist or periodontist, who typically uses
a handpiece less often and with less force.

General Handpiece Maintenance Procedures

A number of steps are mandatory in the general handpiece
maintenance protocol.

Air-Driven High-Speed Handpieces

1. Surface Clean the Handpiece: Prior to removing a
handpiece from the air line, CDC guidelines call for
flushing water through the handpiece in the operatory
for 30 seconds to remove potential contaminants from
the internal water line. Then use a brush under running
water to remove any bio burden from the exterior of the
handpiece. Hold the handpiece upright to reduce the
amount of water entering the head of the handpiece. Do
not use any chemical solutions for cleaning. Chemicals
8

can create reactions during the sterilization cycle that

have a detrimental effect on the sterilizer and the handpiece.
2. Dry the Handpiece: This step is important, especially
if the office is using a chemiclave, or cassette-type sterilizer with a vacuum chamber. Excess water can lead to
corrosion inside the handpiece.
3. Lubricate the Handpiece: Use the proper lubricating tip to spray oil into the drive air line; spray until
oil comes out of the handpiece head, to ensure that the
lubricant has penetrated to the bearings. Even if the
lubricant is delivered incorrectly, oil coming from the
head indicates it has reached the bearings. If you prefer
a dropper, apply two or three full drops to the drive air
line and immediately run the handpiece (the droplets
will not be delivered to the bearings without being propelled by pressurized air).
4. Run the Handpiece to Expel Excess Oil: After lubrication, it is important to run the handpiece to evenly
distribute oil through the bearings and chuck mechanism and to expel excess oil to prevent coagulation during autoclaving. Install a bur in the chuck and run the
handpiece for 20 seconds. Do not use a bur blank - they
are not made to ISO specifications, do not run concentrically, and may damage the turbine. (Note: Some manufacturers specifically state NOT to install a bur prior to
operation.)
Air flush stations located in the sterilization area are
an excellent investment. A flush station eliminates a
return trip to the operatory to run the handpiece. These
stations are readily available from many sources and require only a connection to compressed air. Most stations
have a handpiece adapter that operates the handpiece
upon depressing. Using an air station also prevents oil
from being exhausted back into the handpiece tubing,
leading to discoloration and stiffening. Remove the bur
after operating. Lever-style handpieces must remain in
the closed position during sterilization.
5. Clean Fiber-Optic Surfaces: Alcohol and a Q-tip may
be used to remove excess oil and debris from all fiberoptic surfaces, which will prevent buildup and discoloration.
6. Bag the Handpiece: CDC guidelines recommend
bagging all instruments and handpieces to maintain
sterility. A paper/plastic combination bag allows steam
to evaporate through the paper side while the contents
remain readily identifiable.
7. Sterilize: Autoclave the handpiece following the manufacturers guidelines. Be sure to place the bag paper side
up in the autoclave. Allow the sterilizer to completely
process through the dry cycle. This step is CRITICAL.
If still damp after completion of the full sterilization
cycle, leave the bagged instruments in the autoclave
until the packaging is dry.
www.ineedce.com

Figure 15. Proper lubrication of handpiece

Figure 17. Latch head components

Handpiece Lubricants

Air-Driven Low-Speed Motors and Attachments

CDC guidelines indicate that only the portion of the attachment that comes in contact with patient tissue is
required to be sterilized, or disposed of. It is not necessary
to sterilize the motor if a barrier is used. If you are not autoclaving motors, make sure they are removed from the tubing
and lubricated at least once a week. Not removing motors at
some interval leads to the accumulated disinfectant corroding the threads onto the tubing permanently. Motors, especially rotary vane models, do not require much oil. Dental
motors and attachments require higher viscosity oil than a
high-speed spray. One or two drops of oil in the drive air line
are all that is necessary. Run the motor to distribute the oil.
Also apply some oil as a preventative measure to forward/
reverse valves, shift rings, and sheath attachment points.
Wipe away excess oil with a paper towel. Most straight attachments do not require lubrication. Perform an external
cleaning with a brush under running water prior to bagging
the sheath or nose cone for sterilization.
Figure 16. Low-speed attachments

During the initial warranty period, you should always follow

the manufacturers suggested maintenance procedures and
use the approved lubricant supplied with a new handpiece.
It is important to follow these instructions to the letter to
avoid any disputed warranty claims should your handpiece
fail under warranty. The same is true when you purchase
or have a new original manufacturers turbine installed in
your handpiece. Manufacturers reserve the right to void
your warranty if you are not using their brand of lubricant.
Once your handpiece is out of the warranty period, or if
you choose a different source for handpiece repair than the
original manufacturer, then you are free to use any lubricant
you wish. There are a myriad of choices on the market,
sporting all sorts of claims. Some are advertised as a cleaner
and lubricant in one, some are synthetic, and some advocate
the use of a separate cleaner and oil. That you consistently
employ a good-quality oil matters more than which brand
of oil you choose.

Automatic Lubrication Stations

Many manufacturers offer an automatic clean and lube
station to minimize staff time and take the guesswork
out of the maintenance process. These units vary in cost,
depending on features. One incentive to purchase an automatic lubrication station would be that some manufacturers will significantly extend their handpiece warranties if
their respective automatic stations are used to maintain
the handpieces.
Figure 18. Lubrication stations

It is very important to take latch angles apart for proper

lubrication. If you are processing angles routinely, at least
once a day unscrew the head from the sheath and remove
the transmission gear for cleaning and oiling (try doing this
first thing in the morning as part of the opening routine).
Apply a drop of oil under each gear on the transmission gear
as well as in the center hole. Apply several drops of oil to the
exposed cartridge while the transmission gear is removed.
www.ineedce.com

The simplest lubricator design holds only one handpiece, and the operator must remain at the station to hold
the button down during the entire process. This ensures
a complete cycle of lubrication and flushing, but there
is no time savings for staff. Fully automatic designs will
hold more than one handpiece, including low-speed attachments. Similar to using an autoclave, the operator
loads the machine, closes the door, and presses a button.
This begins the maintenance cycle, and the machine will
dispense the correct amount of lubricant and then operate
each handpiece at the correct running speed. During operation the staff member is free to complete other duties while
the machine runs multiple handpieces through the maintenance cycle. While the automatic machines initially cost
more, there is absolute consistency of operation, which may
result in longer handpiece life and reduced repair costs.
Additional savings may accrue while the staff member
completes normal between-patient tasks and does not need
to use valuable time performing routine handpiece maintenance procedures. One area of concern that is not often
addressed is chuck maintenance. According to a handpiece
manufacturer product manager, Ninety-five percent of all
turbine or attachment problems are found in the head of
the handpiece. Everyone always seems to lubricate the back
end, maybe purge, but do not address the head of the handpiece or the chuck.15 When a handpiece is in operation, the
air is being expelled outward. Once the clinician takes his
or her foot off the rheostat the physics reverse, which can
bring contaminants and tooth dust back into the head of
the handpiece. If these particles are not purged, they bake
onto the internal components and will cause premature
failure. By shooting lubricant and compressed air into the
chuck, this will help dislodge the debris or at least loosen it
up. Once you run a purge cycle by attaching it to the tubing
or maintenance system, the particles are much more likely
to be expelled from the handpiece, extending longevity.

Common Handpiece Maintenance Mistakes

There are a number of common maintenance mistakes that
should be avoided:
1. Using a chemical wipe-down on a handpiece before sterilizing: this is not only redundant, it may multiply harmful
reactions when the handpiece is subjected to heat.
2. Using an ultrasonic cleaner or solution: except for immersion in a cleaning solution offered by the handpiece
manufacturer, handpieces should never be immersed in
any fluids.
3. Lubricating in the wrong hole The drive air line leads
directly to the turbine; other orifices such as exhaust and
water do not. If you are using a liquid oil applicator on a
swivel-type handpiece, it is critical that you deliver oil to
the correct internal opening.
4. Using an incorrect lube applicator Make sure the
spray tip fits the handpiece quick-disconnect correctly.
10

Some models depend on a pressurized fit to flush out

debris.
5. Not applying enough lubricant Sometimes the staff is
directed not to overspray oil into the handpiece, to reduce excess residue; however, it is important to ensure
that oil is getting to the bearings, by seeing oil leave the
head.
6. Not running the handpiece prior to autoclaving Failing
to operate the handpiece following lubrication will gum
up the turbine as excess oil gets baked into the bearings;
an undesirable clinical effect is expelling oil into the operating field after not properly running out the excess.
7. Not cleaning the fiber-optic bundles Failing to keep the
fiber-optic bundle surfaces clean will lead to a buildup of
oil and debris, affecting the ability to transmit light.
8. Leaving the bur in the chuck during autoclaving When
a bur is held in an autochuck, the springs are compressed.
Subjecting any spring to heat and corrosion under tension will weaken it and shorten the life. Leaving a bur in a
manual chuck leads to buildup of debris in the chuck and
increased difficulty of operation.
9. Leaving levers open during autoclaving When a
lever chuck is actuated, about eight pounds of force is
exerted onto the front O-ring of the turbine. During
normal operation this force is momentary as the bur is
changed. Leaving the chuck open during the autoclave
cycle means compressing the O-ring while subjecting it
to heat for 30 minutes. This will dramatically accelerate
turbine failure.
10. Failing to maintain autoclaves If the autoclave is not
properly cleaned, buildup can occur that contaminates
the entire system, including the handpieces.

Handpiece Repair Options

Historically, the most conventional method of restoring a
handpiece to service was to replace the old turbine with a
new one. With replacement intervals measured in years,
cost was no great concern. As the rate of repair increased
once handpieces required sterilization, cost became a consideration. Options available for handpiece repair include
replacing or rebuilding the turbine, either doing this inoffice or sending the handpiece to the original equipment
manufacturer or an independent repair service.
Turbine Replacement
Handpiece turbine repair options include returning the
handpiece to the original equipment manufacturer, purchasing a new turbine from the original manufacturer and
installing it yourself, or purchasing a new aftermarket
or generic turbine and installing it yourself. Before 1992,
standard procedure was simply to order a new turbine from
the original manufacturer or send the handpiece back to
the manufacturer for repair (who may or may not charge a
significant labor fee for installing a new turbine).
www.ineedce.com

In-Office Turbine Replacement

Staff can replace some models in the office, or a sales rep or
service technician could offer help if needed. In this situation, buying a turbine from the company that built your
handpiece guarantees continued quality and consistency.
One advantage of purchasing a new original turbine is the
warranty. Handpiece manufacturers offer warranties on
their in-house repairs as well as on new turbines ranging
from six months to one year, two years or more if their respective automatic maintenance stations are used to process
handpieces for sterilization.
Installing original turbines in the office preserves all the
performance characteristics that influenced the purchase
of that brand in the first place and reduces the cost of replacement. It also eliminates the need for the handpiece to
leave your office, reducing turnaround time associated with
sending handpieces back to a manufacturer. This option
still represents a major expense, and some models may be
complicated to install. Your local dental supply rep can demonstrate proper installation techniques, or you can request
a visit from the manufacturers representative to go over
maintenance and turbine replacement.
Another option for handpiece repair is to install aftermarket replacement turbines. These are turbines produced
by anyone other than the original handpiece manufacturer.
Aftermarket (generic) turbines can be as little as one-third
the cost of a new original turbine. However, although they
are less expensive, the quality of aftermarket turbines varies
depending on the source. Some bearing manufacturers that
supply parts to handpiece manufacturers also market high
quality turbines directly to handpiece repair facilities as well
as dentists. In contrast, some other sources market poor
quality aftermarket turbines that can result in poor handpiece performance; more frequent breakdown; a cycle of
disposability; and greater cost over time than either replacing the failed original turbine with a new original turbine or
rebuilding the original turbine in the first place. Be sure if
you decide to purchase aftermarket turbines that these are
of high quality and that you are purchasing them from a
trusted, reliable source.

Turbine Repair/Rebuild
Rebuilding a turbine instead of replacing it saves money. As
handpiece repair costs escalated, dentists increasingly turned
to local independent repair services to extend turbine life, by
rebuilding as opposed to replacing turbines. Turbine rebuilding services have earned greater acceptance throughout the
dental industry over the years. According to a December 2003
survey of workhorse systems by Dental Products Report, 59
percent of dentists employ a dedicated handpiece repair shop
to maintain their handpieces.16 One handpiece manufacturer
has now adopted this lower-cost option when they have to
replace a turbine under warranty. At a high-quality independent repair service, a technician will evaluate the turbine to
www.ineedce.com

determine if the key component parts remain usable and safe.

A turbine can be rebuilt effectively (vs. buying a whole new
turbine) if the spindle/chuck assembly is not worn enough to
degrade performance. The technician will replace the damaged bearings and supporting O-rings with new ones meeting
factory specifications. Rebuilding a turbine properly consists
of carefully removing the broken bearings without damaging
the rest of the assembly. New bearings are then pressed onto
the spindle/chuck assembly. The suspension O-rings are
critical to handpiece performance and are replaced as well. Independent studies cited earlier confirm that it is usually only
the bearings that fail. As long as the remaining components
are still serviceable, total replacement is unnecessary.
Figure 19. Turbine assembled and unassembled

The price for rebuilding a turbine is usually around $100

substantially lower than the cost of a new original manufacturer replacement turbine. Warranties offered on rebuilt turbines
range from three months to one year, depending on handpiece
models and the experience and ability of the technician. Most
repair services offer relatively fast turnaround, minimizing
downtime and eliminating the need to own extra handpieces.
The major disadvantages of independent repair services are
that everything depends on the individual skill and experience
of the technician performing the work as well as access to the
right repair parts and specialty tooling; these can vary widely
among services. There are no uniform standards of practice,
and no certifying body exists within the industry. One solution is to find a repair facility that has technicians certified
by a handpiece manufacturer, or that at least has a relationship with handpiece manufacturers, and the ability to offer
original replacement parts. Handpiece manufacturers do not
distribute high-speed turbine component parts; they sell only
complete assemblies. How then can independent repair shops
obtain original parts? Higher-quality repair shops are able to
purchase directly from the component parts manufacturer.
It takes knowledge, experience, and a willingness to do what
is best for the customer for an independent repair service to
make the extra effort to obtain the correct original parts.
Some dentists decide to rebuild their turbines in the dental office using a commercially available do-it-yourself process. This approach may be acceptable for simpler designs
but risks damaging more sophisticated turbine assemblies.
Quality of parts selected may be a concern, depending on
the source, and the skill and attention to detail of the repairer
in the dental office can vary substantially.
11

Evaluating Claims Made by the Handpiece

Industry
Very few companies are able to produce the miniature precision bearings capable of performing under the tremendous
speeds required by dentistry and of withstanding harsh sterilization conditions. The current CDC guidelines recommend autoclaving of dental handpieces after use for a single
patient.17 Due to the highly specialized nature of precision
bearing production, dental handpiece manufacturers purchase bearings and other components from only a limited
number of suppliers. Exact specification dental bearings and
other parts are available to independent repair services from
these same bearing manufacturers.
Quality ratings for bearings are established by the Annular Bearing Engineering Committee (ABEC) of the American Bearing Manufacturers Association. Quality is rated on
the ABEC scale from 1 to 9. For example, rollerblade skate
bearings are ABEC 3. The dental industry standard begins
at ABEC 7. A plethora of bearing designs and specifications
are available for handpiece repair. Using cheap or incorrect
bearings is one reason why repair quality varies so much
from shop to shop. If the technician is not installing a bearing as good as that originally specified by the manufacturer,
handpiece performance will suffer. A quality repair shop
should know which bearing is specified by the handpiece
manufacturer and should be using only the correct bearings
as replacements.

Factors to Consider When Choosing a Handpiece Repair Service

Deciding where to turn to for handpiece repair can be
challenging. Cost and turnaround time are major considerations that may result in a dental office selecting an
option other than returning the handpiece to the original
equipment manufacturer outside of warranty period. On
the other hand, if a handpiece repair service is selected, care
must be taken to select one that will not result in poor quality instead of higher cost ultimately, poor quality leads
to high cost, too, and major inconvenience. If selecting a
repair service, considerations include the following:
1. Training: Make sure your service provider has made
a significant investment in training and equipment and
takes continuing education courses to remain current on
new products and techniques. Simply attending a weekend seminar or watching a video is not enough. Without
adequate training, even a well-meaning person will produce poor results and possibly damage your handpiece.
2. Make sure repairs are performed in-house: If a repair
service simply acts as a middleman for a repair facility
elsewhere, you may experience a lack of quality control,
longer turnaround times, and limited customer service.
3. Use of genuine manufacturer turbines: Some repair
services replace the dentists original turbine with an
inferior generic replacement without informing the
12

dentist of the substitution. This is unethical. A handpiece is a sophisticated device and can easily be compromised with improper techniques and inferior parts.
Watch out for nebulous claims such as same as manufacturers specifications or manufacturer-quality
parts. There should be no room for interpretation. If
a repair shop claims to supply original turbines, then
original packaging and instructions should accompany
these installations.
4. Relationship with the repair service: The best service results from dealing directly with the technician
who performs the repair, not with customer service or
voicemail. Dental professionals need to establish a trusting relationship with someone who can easily articulate
exactly what services are being provided.
5. Obtaining estimates: Repair options and costs should
be spelled out clearly. Communication is vital in order
for you to be sure you are receiving exactly what you are
paying for. Be wary of companies that do not provide
published pricing and of repair contracts promising to
service handpieces for a fixed fee (which result in an incentive to replace as few parts as possible instead of performing a complete overhaul of the turbine if required).
Some companies offer clean and lube services at prices
up to $45. This can be done in the office by the staff instead, at no cost and until a high-speed handpiece actually fails, daily staff maintenance is all that is required to
prolong its life.
6. Get a warranty: A quality repair operation should
provide a substantial warranty on all repairs. Another
indicator of a qualified service is the ability to facilitate
and provide original factory repairs if these are necessary
(not all handpiece repairs can be performed correctly in
the field).
7. Honest advice and commitment: An ethical service
provider should inform the office when total replacement
makes more sense. A good repair service holds a sincere
interest in serving the needs of dental professionals and
should be committed to improving the overall industry.
Look for a company that belongs to a trade association
and supports local dental society meetings and events.

Summary
Handpieces are one of the most important workhorse systems in the dental practice and require routine autoclaving,
yet they have an often undeserved reputation for excessive
breakdown and expense. If you maintain your handpieces
properly, you will get many years of optimal performance;
and, when the time comes to repair your handpiece, consideration should be given to the quality of the repair and
reliability of a qualified service provider to restore your
workhorse to optimal performance. The bottom line is that
handpieces represent a significant investment and play a
vital role in any dental practice.
www.ineedce.com

References:
1

2
3
4
5
6
7
8
9
10
11
12
13
14

Ring ME. The true discoverer of the dental air turbine

handpiece, Sir John Walsh of New Zealand. Bull Hist Dent. 1987
Oct;35(2):106-9.
http://www.dentalproductsreport.com/articles/show/
dpr0709_pf_handpieces
Lewis DL, Boe RK. Cross-infection risks associated with current
procedures for using high-speed dental handpieces. J Clin
Microbiol. 1992 Feb;30(2):401-6.
Breo DL. Meet Kimberly Bergalis--the patient in the dental
AIDS case. JAMA. 1990 Oct 17;264(15):2018-9.
FDA Guideline to Dentists, September 28, 1992.
CDC/FDA Medical Bulletin March 1993.
Electric Handpiece Systems. ADA Professional Product Review,
vol. 2, issue 1.
Choi C, Driscoll CF, Romberg E. Comparison of cutting
efficiencies between electric and air-turbine dental handpieces.
J Prosthet Dent. 2010 Feb;103(2):101-7.
Available at: http://www.fda.gov/MedicalDevices/Safety/
AlertsandNotices/ucm226995.htm
Leonard DL, Charlton DG. Performance of High-Speed
Dental Handpieces Subjected to Simulated Clinical Use and
Sterilization. J Am Dent Assoc. 1999;130(9):1301-11.
Advancements in Handpieces 10 Years After Sterilization.
Clinical Research Associates Newsletter, October 2000.
Dyson JE, Darvell BW. Flow and free running speed
characterization of dental air turbine handpieces. J Dent. 1999
Sep;27(7):465-77.
ISO Standard 7785-1, Dental Handpieces, International
Standards Organization, 1992.
Monagahn DM, Wilson NH, Darvell BW. The performance of

air-turbine handpieces in general dental practice. Oper Dent.

2005 Jan-Feb;30(1):16-25.
15 Personal Communication. Eric Ozelski, Product Manager for
SciCan.
16 Survey of Workhorse Systems. Dental Products Report,
December 2003.
17 Centers for Disease Control and Prevention. Guideline for
disinfection and sterilization in healthcare facilities, 2008.
Available at: http://www.cdc.gov/ncidod/dhqp/pdf/guidelines/
Disinfection_Nov_2008.pdf. Accessed December 8, 2008.

Author Profile

Glenn Williams, BS
Glenn Williams is a twenty-five year veteran of
the dental industry, specializing in handpieces
since 1987. From 1987-1994, Glenn worked for
a major handpiece manufacturer. He has owned
and operated a successful handpiece repair service in Northern California since 1994. Glenn
was one of the founding members, and is President, of the National Dental Handpiece Repair Association. The
NDHRA is an association of other dedicated independent handpiece professionals who desire to better serve the dental profession
through advancing the handpiece repair industry by establishing
and maintaining high standards of service.

Disclaimer

The author of this course owns and operates an independent repair service
and is the President of the National Dental Handpiece Repair Association.

Reader Feedback

We encourage your comments on this or any PennWell course. For your

convenience, an online feedback form is available at www.ineedce.com.

Online Completion

Use this page to review the questions and answers. Return to www.ineedce.com and sign in. If you have not previously purchased the program select it from the Online Courses listing and complete the
online purchase. Once purchased the exam will be added to your Archives page where a Take Exam link will be provided. Click on the Take Exam link, complete all the program questions and submit your
answers. An immediate grade report will be provided and upon receiving a passing grade your Verification Form will be provided immediately for viewing and/or printing. Verification Forms can be viewed
and/or printed anytime in the future by returning to the site, sign in and return to your Archives Page.

Questions
1. Pioneering work for the air-driven
high-speed handpiece was performed by
_______.
a.
b.
c.
d.

Sir John Nash

Sir James Black
Sir James Walsh
Sir John Walsh

2. Increased concentricity results in

_______.
a.
b.
c.
d.

a smoother cut
better margins
less vibration
all of the above

3. Most of what we now take for granted as

restorative dentistry was made possible
because of the advancing technology of
the _______.
a.
b.
c.
d.

hybrid handpiece
air-driven handpiece
electric handpiece
all of the above

6. The FDA issued the first guidelines

mandating routine handpiece sterilization
for private dental practices in the _______.

11. In recent years, newer handpiece models

have become available, operating in a
range of _______.

7. The clinician should apply careful

consideration to the _______ of a
particular handpiece model when making
a purchase decision.

12. A handpiece with a wider, flared body

shape toward the rear of the handpiece
_______.

a.
b.
c.
d.

a.
b.
c.
d.

1960s
1970s
1980s
1990s

features
reliability
maintenance requirements
all of the above

8. A small head size in a handpiece_______.

a.
b.
c.
d.

improves visibility
improves access
improves seizing
a and b

4. Automatic chucking mechanisms were

developed in an effort to _______.

9. Larger head sizes in handpieces _______.

5. Tubing torque is defined as the _______

the operator feels from the weight of the
tubing transferred through the handpiece.

10. The typical handpiece head is angled

back at _______.

a.
b.
c.
d.

a.
b.
c.
d.

speed up the changing of burs

speed up the removal of debris
automate bur rotational speed adjustment
a and c

resistance or drag
rotation
pressure
all of the above

www.ineedce.com

a.
b.
c.
d.

a.
b.
c.
d.

incorporate a larger turbine impeller

yield higher power output
result in less time involved in tooth preparation
all of the above

12.5 degrees
17.5 degrees
22.5 degrees
27.5 degrees

a.
b.
c.
d.

38 to 51 decibels
48 to 61 decibels
58 to 71 decibels
none of the above

a. reduces the pinching force required to grip the

handpiece
b. reduces hand fatigue
c. reduces wrist fatigue
d. all of the above

13. An electric handpiece _______.

a. is louder than an air-driven high-speed handpiece

b. has differences between freerunning speed and
active speed
c. loses power while cutting tooth structure
d. none of the above

14. Fiber optics and multiport water spray

are available in _______.
a.
b.
c.
d.

electric handpiece attachments

air abrasion units
high-speed air-driven handpieces
a and c

15. The most commonly used electric

handpiece attachment for operative
dentistry is a _______.
a.
b.
c.
d.

1:3 step-up
1:5 step-up
1:7 step-up
any of the above

13

Questions (Continued)
16. It is imperative that you stop using an
electric handpiece immediately if you
_______.
a.
b.
c.
d.

feel any heat during use

hear any noise during use
notice any reduction in vibration
all of the above

17. Handpiece life expectancy dropped

dramatically during the 1990s due to
_______.
a.
b.
c.
d.

contamination with bacteria

repeated sterilization
debris entering the handpiece
all of the above

18. _______ is a variable that affects turbine

life.
a.
b.
c.
d.

Lubrication
Conditions of use
Maintenance practices of the individual office
All of the above

19. In one study, DIS concluded that the

dentist can expect a handpiece to survive
approximately _______ sterilization cycles
without significantly reduced performance,
if the handpiece is properly maintained.
a.
b.
c.
d.

250
500
750
none of the above

27. Free speed is the maximum rpm with

_______.

39. Dental motors and attachments require

_______ than a high-speed spray.

28. As the turbine bearings wear, speed

decreases and results in _______.

40. Using a chemical wipe-down on a

handpiece before sterilizing _______.

a.
b.
c.
d.
a.
b.
c.
d.

no load
load
activation
a and c

longer preparation times

slower cutting
rougher margins
all of the above

29. The more concentrically a handpiece

operates, the _______.
a.
b.
c.
d.

smoother the bur cuts

less perceptible vibration is
more comfort patients experience
all of the above

30. A high-speed turbine contains _______.

a.
b.
c.
d.

a chucking mechanism
a vibratory system
a rotary system
a and c

31. Handpieces fail as a result of catastrophic

failure of the _______.
a.
b.
c.
d.

chuck
spindle
turbine bearings
all of the above

a.
b.
c.
d.

higher viscosity oil

lower viscosity oil
silanized oil
b and c

a. is redundant
b. is necessary
c. may multiply harmful reactions when the
handpiece is subjected to heat
d. a and c

41. Handpiece turbine replacement options

include _______.

a. returning the handpiece to the original equipment

manufacturer
b. purchasing a new turbine from the original
manufacturer and installing it yourself
c. purchasing a new aftermarket or generic turbine
and installing it yourself
d. all of the above

42. Installing original turbines in the office

_______.
a. preserves the performance characteristics of the
handpiece
b. reduces the cost of replacement
c. eliminates the need for the handpiece to leave your
office
d. all of the above

20. An air-driven high-speed handpiece

consists of two main components: the
_______.

32. The retainer, or cage, that secures the

ball bearings within the raceways

43. Rebuilding a turbine properly consists

of _______.

21. The current state-of-the-art in handpiece construction is _______.

33. _______ is a symptom of bearing failure.

44. If you select an independent handpiece

repair service, it is important to _______.

a.
b.
c.
d.
a.
b.
c.
d.

body and the turbine

turbine and the impeller
body and the spindle
body and the outlet
titanium
stainless steel
brass
none of the above

22. Manufacturers claim that virtually no

degradation occurs with _______ optics
and back their claims with a five-year
warranty.
a.
b.
c.
d.

glass fiber
cellular
chip
all of the above

23. A major problem associated with

handpiece sterilization is the continual
buildup of _______.
a.
b.
c.
d.

bacterial debris
rust and corrosion
lysed sterilization products
all of the above

24. The latest handpiece models feature a

multi-port water spray that _______.

a. disperses air and water evenly around the work area

b. disperses lubrication and water evenly around the
work area
c. disperses water evenly around the work area
d. all of the above

25. The component that fails most often on

a high-speed air-driven handpiece is the
_______.
a.
b.
c.
d.

impeller
turbine
chuck
none of the above

26. Turbines rotate at speeds ranging from

_______.
a.
b.
c.
d.

14

180,000 to 250,000 rpm

280,000 to 350,000 rpm
380,000 to 450,000 rpm
none of the above

a. becomes brittle as it is subjected to harsh sterilization environments

b. disintegrates upon failure
c. becomes eccentric after 200 cycles
d. a and b
a. The bur stalling out when applied to tooth
structure
b. Unacceptable vibration when the handpiece is
activated
c. Unusually loud sounds emanating from the turbine
d. all of the above

34. ______ can have an impact on turbine life.

a.
b.
c.
d.

Overusing dull burs

Long cutting burs
Incorrect bur seating in the autochuck
all of the above

35. Prior to removing a handpiece from the

air line, CDC guidelines call for flushing
_______ through the handpiece in the
operatory for _______.
a.
b.
c.
d.

ethanol; 20 seconds
ethanol; 30 seconds
water; 20 seconds
water; 30 seconds

36. After lubrication, it is important to

_______.

a. run the handpiece to evenly distribute oil through

the bearings and chuck mechanism
b. avoid running the handpiece prior to sterilization
c. ensure excess oil is present to allow for waste
d. a and c

37. A flush station _______.

a. eliminates a return trip to the operatory to run the

handpiece
b. requires only a connection to compressed air
c. prevents oil from being exhausted back into the
handpiece tubing
d. all of the above

38. After autoclaving a handpiece, _______.

a. the handpiece may be removed halfway through
the dry cycle
b. the packaging must be completely dry before it is
removed from the autoclave
c. the handpiece should be sprayed with disinfectant
to maintain sterility
d. a and c

a. carefully removing the broken bearings without

damaging the rest of the assembly
b. pressing new bearings onto the spindle/chuck assembly
c. replacing the suspension O-rings
d. all of the above
a.
b.
c.
d.

get a warranty
ensure the technician has adequate training
make sure the repair service is using the correct bearings
all of the above

45. Until a high-speed handpiece actually fails,

______ is all that is required to prolong its life.
a.
b.
c.
d.

daily maintenance by staff

weekly servicing
monthly check-ups by the handpiece technician
all of the above

46. Failing to keep the fiber-optic bundle

surfaces clean will _______.
a.
b.
c.
d.

lead to a buildup of oil

lead to a buildup of debris
affect the ability to transmit light
all of the above

47. Quality ratings for bearings are

established by the _______.
a.
b.
c.
d.

Annular Bearing Engineering Council

American Bearing Association
Annular Bearing Engineering Committee
none of the above

48. The dental industry for bearings begins

at _______.
a.
b.
c.
d.

ABEC 3
ABEC 5
ABEC 7
ABEC 9

a.
b.
c.
d.

49 percent
59 percent
69 percent
none of the above

a.
b.
c.
d.

your local dental assisting school on request

anyone other than the original handpiece manufacturer
the original handpiece manufacturer
all of the above

49. According to a 2003 survey, _______ of

dentists employ a dedicated handpiece
repair shop to maintain their handpieces.

50. An aftermarket turbines is one that is

produced by _______.

www.ineedce.com

ANSWER SHEET

Anatomy of a Handpiece: Understanding Handpiece Maintenance and Repairs

Name:

Title:

Address:

E-mail:

City:

State:

Telephone: Home (

Office (

Specialty:

ZIP:

Country:

Lic. Renewal Date:

Requirements for successful completion of the course and to obtain dental continuing education credits: 1) Read the entire course. 2) Complete all
information above. 3) Complete answer sheets in either pen or pencil. 4) Mark only one answer for each question. 5) A score of 70% on this test will earn
you 3 CE credits. 6) Complete the Course Evaluation below. 7) Make check payable to PennWell Corp. For Questions Call 216.398.7822

Educational Objectives

For immediate results,

go to www.ineedce.com to take tests online.
Answer sheets can be faxed with credit card payment to
(440) 845-3447, (216) 398-7922, or (216) 255-6619.

1. List and describe the major components of air-driven high-speed handpieces and electric handpieces.
2. List and describe the major differences between air-driven high-speed handpieces and electric handpieces.
3. List and describe the signs of failure for air-driven and electric handpieces.

P ayment of $59.00 is enclosed.

(Checks and credit cards are accepted.)

4. List and describe the maintenance steps for air-driven handpieces.

5. List and describe the options for repair/rebuild of air-driven handpieces and considerations in selecting from these options.

If paying by credit card, please complete the

following:
MC
Visa
AmEx
Discover
Acct. Number: ______________________________

Course Evaluation

Exp. Date: _____________________

Please evaluate this course by responding to the following statements, using a scale of Excellent = 5 to Poor = 0.
1. Were the individual course objectives met?

O bjective #1: Yes No

Objective #2: Yes No
Objective #5: Yes No

Charges on your statement will show up as PennWell

Objective #3: Yes No

Objective #4: Yes No

2. To what extent were the course objectives accomplished overall?

3. Please rate your personal mastery of the course objectives.

4. How would you rate the objectives and educational methods?

5. How do you rate the authors grasp of the topic?

6. Please rate the instructors effectiveness.

7. Was the overall administration of the course effective?

8. Do you feel that the references were adequate?

Yes

No

Yes

No

9. Would you participate in a similar program on a different topic?

31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.

10. If any of the continuing education questions were unclear or ambiguous, please list them.
___________________________________________________________________
11. Was there any subject matter you found confusing? Please describe.
___________________________________________________________________
___________________________________________________________________
12. What additional continuing dental education topics would you like to see?
___________________________________________________________________
___________________________________________________________________
If not taking online, mail completed answer sheet to

Academy of Dental Therapeutics and Stomatology,

A Division of PennWell Corp.

P.O. Box 116, Chesterland, OH 44026

or fax to: (440) 845-3447

AGD Code 148, 550

PLEASE PHOTOCOPY ANSWER SHEET FOR ADDITIONAL PARTICIPANTS.

AUTHOR DISCLAIMER
The author of this course owns and operates a handpiece repair service company and is
President of the NDHRA.
SPONSOR/PROVIDER
This course was made possible through an unrestricted educational grant. No
manufacturer or third party has had any input into the development of course content.
All content has been derived from references listed, and or the opinions of clinicians.
Please direct all questions pertaining to PennWell or the administration of this course to
Machele Galloway, 1421 S. Sheridan Rd., Tulsa, OK 74112 or [email protected].
COURSE EVALUATION and PARTICIPANT FEEDBACK
We encourage participant feedback pertaining to all courses. Please be sure to complete the
survey included with the course. Please e-mail all questions to: [email protected].

www.ineedce.com

INSTRUCTIONS
All questions should have only one answer. Grading of this examination is done
manually. Participants will receive confirmation of passing by receipt of a verification
form. Verification forms will be mailed within two weeks after taking an examination.
EDUCATIONAL DISCLAIMER
The opinions of efficacy or perceived value of any products or companies mentioned
in this course and expressed herein are those of the author(s) of the course and do not
necessarily reflect those of PennWell.
Completing a single continuing education course does not provide enough information
to give the participant the feeling that s/he is an expert in the field related to the course
topic. It is a combination of many educational courses and clinical experience that
allows the participant to develop skills and expertise.

COURSE CREDITS/COST
All participants scoring at least 70% on the examination will receive a verification
form verifying 3 CE credits. The formal continuing education program of this sponsor
is accepted by the AGD for Fellowship/Mastership credit. Please contact PennWell for
current term of acceptance. Participants are urged to contact their state dental boards
for continuing education requirements. PennWell is a California Provider. The California
Provider number is 4527. The cost for courses ranges from $39.00 to $110.00.
Many PennWell self-study courses have been approved by the Dental Assisting National
Board, Inc. (DANB) and can be used by dental assistants who are DANB Certified to meet
DANBs annual continuing education requirements. To find out if this course or any other
PennWell course has been approved by DANB, please contact DANBs Recertification
Department at 1-800-FOR-DANB, ext. 445.

Customer Service 216.398.7822

RECORD KEEPING
PennWell maintains records of your successful completion of any exam. Please contact our
offices for a copy of your continuing education credits report. This report, which will list
all credits earned to date, will be generated and mailed to you within five business days
of receipt.
CANCELLATION/REFUND POLICY
Any participant who is not 100% satisfied with this course can request a full refund by
contacting PennWell in writing.
2010 by the Academy of Dental Therapeutics and Stomatology, a division
of PennWell

ANAT0111C
15