Adr245b V2 10

Download as pdf or txt
Download as pdf or txt
You are on page 1of 20

Type: ADR245B

ASHIDA Numerical Directional 3OC + 1EF

( AD I T Y A V 2 S e r i e s )

Protection Relay

Protection Features:
9

(Preliminary)

Internal calculation of zero seq. EF

4 Element (3 Phase + EF +sensitive EF)

current (3Io) and Zero sequence voltage

Directional / Non Directional Over current

(3Vo) for directional detection for Earth

IDMT/DMT.

fault.

Negative Phase Sequence element (46)

Selection of Curve: Five selectable curves


(Normal Inverse1 (C1), Normal Inverse2,

NDV Protection with Definite or IDMT


characteristic.

(C2) Very inverse (C3), Extremely Inverse

Definite time or IDMT UV/OV


characteristic

(C4), Long Time Inverse (C5)) and Define


9

Time (C6).

Relay Design Features:

Instantaneous Over-Current Protection with

Large 20x4 LCD display for Parameter and


setting display.

adjustable timer.
9

Disturbance Recorder. Up 3sec of actual

Breaker Failure detection.

In-built CB Trip Circuit Supervision function

waveform of current & voltage along with

during pre closing and post closing of CB.

logical and physical status are captured

In built Auto Reclose Relay (ARR).

& saved in the built-in memory with date

On site CT Secondary selection 1A or 5A.

time

In built VT supervision features and

condition & fault location.


9

under/over voltage Alarm.


9

Internal

reconstruction

for direction detection.

for

analyzing

fault

Pre fault & Post fault duration can be


selectable in Disturbance Recorder.

phase-phase

voltage and open delta voltage required

stamping,

Disturbance Recorder can be trigger by


External Digital Input.

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 1 / 16

Type: ADR245B

ASHIDA Numerical Directional 3OC + 1EF

( AD I T Y A V 2 S e r i e s )

Protection Relay
9

Fully communicable with IEC standard open

(Preliminary)

4. Digital Input output module.

protocol. IEC60870-5-103, MODBUS & IEC


The

61850.
9

Separate Communication Port for SCADA

Online display of CB status and other digital

Continuous monitoring of modules internal


hardware and alarm generation in case of

11 Digital Output contacts for local alarm as

2 Setting Groups.

CB CLOSE/TRIP from Relay keyboard

10 Optically isolated digital status input for

9
9

continuously monitors phase, E/F current and PT

isolated status connections. The high-speed

voltage signals through a A/D converter. The


Digital Signal performs powerful Numerical

harmonic contents of the current and voltage, the

protection

Controller

direction of power flow then this value is used for

well as tele-signalling.

Signal

Algorithms to find out RMS of fundamental &

failure of any critical components.


9

Digital

micro-controller samples these current and

and logical status.


9

speed

Secondary voltage along with different optical

(RS485) as well as Local testing (RS232C)


9

High

and

metering

function.

All

measurement is tuned to fundamental frequency


i.e 50 or 60Hz depending upon setting, thus

monitoring of status and avoid used of

relay remain stable during distorted waveform by

external relay logic.

various industrial load. All these measure values

2 dedicated status input for Trip Circuit

are then used for different protection function

Monitoring.

such as IDMT/DMT Over current protection,

5000 nos of event memory, event such CB

Instantaneous Over current protection, Earth

close, Trip, digital status change, relay pkp

Fault protection, IDMT/DMT Directional Over

etc. All events are with date and time

Current

stamped up to 1ms.

Directional

10 nos of Fault data stored with keypad

protection etc. These measured values are also

interface and time stamping.

displayed on large 20 x 4 LCD display for

Display of Voltage, current, PF, Active,

metering purpose. The DSC also monitors

Reactive Power in terms of Primary value.

and

Earth

Over

Fault,

Current

Instantaneous

and

Earth

Fault

different digital input through optical isolator and


perform some monitoring function such trip

Description:
ADR245B

is

circuit supervision, and control potential free


second

generation

Numerical

Directional Over Current Earth fault Relay.


consist

all

the

necessary

protection

It

contact for control CB and generate ALARM and


Tele-signalling

and

monitoring functions required for Normal feeder


It consist of
1. High Speed Digital DSP Controller
2. Analog Measuring Module
3. Power supply Module

The power supply module is basically DC DC


converted designed using modern PWM based
Switching mode technique to convert 110Vdc
station battery supply to the 12V and 24Vdc low
voltage supply for relay electronics and control
circuit. It also provides necessary isolation from

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 2 / 16

ASHIDA Numerical Directional 3OC + 1EF

Type: ADR245B
( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

station battery. There are two type of power

directional over current (Ip1>, Ip2>, IP>>, &

supply modules are available 1) having range of

IP>>>). Stage 1 (>) stage 2 (>>) can be

77Vdc 250Vdc. Covering requirement of

programmed as IDMT or Definite Time. All major

110Vdc and 220Vdc station battery system 2)

international IDMT curves are available. Stage 3

having range of 18Vdc to 250Vdc covering

(>>>) can be programmed Instantaneous or

24Vdc, 30Vdc, 110Vdc and 220Vdc station

Define Time. Range of for stage 1 and 2 is 10%

battery requirement.

to 250% for phase the output of stage 1 (Ip>) is

The relay is having total 8 nos of high intensity

separate and not connected to trip contact. The

dual LED for easy identification of type of fault

output of Ip1> and Ip2> can be assigned to any

for easy user interface. LEDs L2 to L8, digital

of 10 programmable relay through key board.

status input and control output R1 to RB are fully

While output of Ip>> and Ip>>> is connected to

programmable via keypad interface.

trip element. Thus Ip> can be used as ALARM


before TRIP or can be used to TRIP another CB

Main Functions
The ADR245B are having following protection
functions.

before tripping main CB.


Although the curves tend towards infinite when
the current approaches Is (general threshold),

1. 4 stage of Directional phase Over current


element. (Ip1>, Ip2>, Ip>> and Ip>>>).
2. 3 stages of Directional 3Io (Internally derived
EF) (3Io>, 3Io>> and 3Io>>>).

the minimum guaranteed value of the operating


current for all the curves with the inverse time
characteristic is 1.1Is (with a tolerance of
0.05Is).

3. 3 stages of Directional Ie (Externally EF or


REF) (Ie>, Ie>> and Ie>>>).

Earth Fault Element:

4. Negative phase sequence element.

The relay has two different type of Earth Fault

5. Under / over voltage Protection.

one is marked as 3Io and another is marked as

6. Neutral Displacement voltage Protection.

Ie. The 3Io is derived internally by software

7. Trip Circuit Super vision.

through phase current while Ie is measured from

8. Breaker Failure Detection.

external CT. Thus Ie can be used as Core

9. Monitoring Functions.

Balance CT (CBCT) or Restricted EF (REF).

10. Auto Recloser Relay (ARR).

Each EF is having 3 stages (>, >>, & >>>).

11. Relay / LED configuration

Stage 1 (>) stage 2 (>>) can be programmed as

Each of these functions are independently

IDMT or Definite Time. All major international

programmable and can be enable or disable by

IDMT curves are available. Stage 3 (>>>) can be

user depending upon requirement.

programmed instantaneous or Define Time.


Range for stage 1 and stage 2 3Io is 10% to

Over Current Element:


The ADR245B is member of Ashida Numerical
Relay family design for protection general

100% and for stage 3 3Io is 50% - 1200%. The


Range for EF is from 5% to 80% for stage 1,
stage 2 and 50% to 1200% for stage 3. The

feeder. The relay has four independent stages of


Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 3 / 16

Type: ADR245B

ASHIDA Numerical Directional 3OC + 1EF

( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

output of stage 1 (Ie>) is separate and not

The separate output contact allows to use each

connected to trip contact. The output of > can be

stage for independent function such as stage 1

assigned to any of 10 programmable relay

can be used for ALARM stage 2 for tripping or

through key board. While output of >> and >>> is

both can be use for tripping independent CB.

connected to trip element. Thus Ie> can be used

Each stage can enable or disable depend upon

as ALARM before TRIP or can be used to TRIP

application.

another CB before tripping main CB.


As standard practice all direction relay use two
healthy phase voltage for direction detection and
use MTA setting for phase angle correction. For
example R phase element use R phase current
and Y, B phase voltage. In ADR245B use
standard star connection at relay side and
internally reconstruct phase to phase voltage
required for direction detection. Similarly relay
calculates open delta voltage (3Vo) and EF
current (3Io) required for detection of EF

Trip Circuit Supervision:The ADR245B is having 2 separate digital optocoupler status input which can be used to
continuously monitor continuity of trip-circuit. The
general scheme is as shown in fig. 4.
Relay monitor Trip coil continuity through CB NO
during close condition and through CB NC during
Trip condition. If any discontinuity observed it
generate Alarm signal.
The output marked as PROTH (Protection
healthy) is normally is ON and become OFF at

element.

following condition
Inverse Time Curves:The each stage thresholds for phase (earth) over

B+

TCCOM

1
6

current can be selected with an Inverse Definite

CB NO

Minimum Time (IDMT) characteristic. The time

To Relay CPU

T1

B-

delay is calculated with a mathematical formula

T2

TC

t=

Fig.4 Trip Circuit Logic

Iref
Curve
Type
C1
C2
C3
C4
C5
C6

To Relay CPU

CB NC

K * a
I

6
2

When DC supply is not sufficient (DC fail)

When T1 and T2 both active or both inactive.

i.e CB NO as will as CB NC are both close or

Description

Standard
Inverse_1
Standard
Inverse_2
Very Inverse
Extremely
inverse
Long Time
Inverse
Define Time

0.14

0.02

0.06

0.02

13.5
80

1
2

The ADR245B is provided with 4 shot Auto

120

recloser 1) Dead Time for shot 1 (DT1) 2) Dead

open. Relay detects any internal hardware


Error.
Auto Recloser Logic:-

recloser function. There are 4 timer for auto

Time for shot 2 (DT2) 3) Dead Time for shot 3

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 4 / 16

ASHIDA Numerical Directional 3OC + 1EF

Type: ADR245B
( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

(DT3) 4) Dead Time for shot 4 (DT4) and 5)

below under voltage setting relay start internal

Reclaim Time (RT). After clearing of fault

timer (settable from 0.1 to 10 sec in steps of 0.1

ADR245B trigger dead Time 1 i.e DT1. after the

sec). If voltage remain abnormal during is time

time delay Relay provide reclose command and

relay generate Alarm signal. Any of the output

start reclaim timer RT. If second fault occur

element from RL1 to RLB can be assign to this

during RT relay trigger Dead Time 2 i.e DT2. If

function. The output can be use for alarm or

third fault occur during RT relay trigger Dead

tripping of CB.

Time 3 i.e DT3, If Fourth fault occur during RT


relay trigger Dead Time 4 i.e DT4 and after time
delay it again provide reclose command and
retrigger RT. If fifth fault occur during RT Relay
generate Lock-Out alarm and block further
reclose. The Lock-Out condition can be reset
locally as well remotely by SCADA through
communication digital status input.

Negative sequence over current (46): The ADR245B relay will be included
programmable function to detect unbalanced
fault conditions. When earth fault elements are
not operated or not sufficiently sensitive. The
ADR245B include negative phase sequence
over current element it can be programmed as
IDMT or definite time the actual setting range
will be finalized during later stage of design.

Breaker Failure Detection :Normally after tripping current should become


Zero within 100 200ms time depend upon
type of fault and breaker mechanism. After Fault
ADR245B trigger internal timer (settable from
0.1s to 2.0s) if fault is not cleared during this
time then relay declare as Breaker fail (LBB
function) and change another contacts. These
contacts is marked as Breaker Fail can be used
to TRIP back up breaker or can be used to

Neutral Displacement Voltage Protection :Neutral displacement voltage protection function


is provided with internal & External selection.
With internal setting it uses 3Vo voltage (Open
Delta voltage) for sensing. In external setting it
uses external PT Voltage (Terminals C27 & C28)
for sensing. The setting is from 5.5V to 20V. Any
output elements i.e. from RL1 to RLB can be
assign to this function.

generate ALARM signal.


Under / Over Voltage Alarm :The ADR245B relay will

Setting Group:The relay is provided with two setting groups G1


be

included

programmable function to detect under / over


voltage conditions. Relay had separate under
voltage and over voltage element. The under

and G2, one of the groups is active at time. The


setting group can changed from digital input, this
allow user to change relay setting dynamically as
per outgoing load CB condition.

voltage setting is from 25% to 95% and over


voltage setting from 105% to 155% of rated
(100% = 65.5V). Each function can be separately
enable or disable independently. Whenever any
phase voltage is above over voltage setting or

Programmable DI/DO and LED:The ADR245B has 11 digital outputs, 10 optoisolated input and 7 general purpose LEDs.
These can be programmed by local key board.

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 5 / 16

Type: ADR245B

ASHIDA Numerical Directional 3OC + 1EF

( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

Any logical of physical status can be assigned to

pick, trip operation of relay. This waveform

any relay contact The logic of digital status input

can be downloaded through communication port

as well as logical status can be formed and

for further analysis.

assigned to any of the relay output. The


disturbance record can be trigger from external
logical input.

Relay Talk Software:


The

general

communication

software

is

provided to communicate with relay, known as


Monitoring Functions (Event, Disturbance

Relay Talk. By using this software data such as

Record):-

event log, disturbance records etc can be down

Relay support IEC60870-5-103 / IEC61850 and

loaded and can be further analysis. The

modbus protocol. The In communicable version

disturbance record data can be saved in

IEC61850 is optional and need to specify while

standard

ordering while IEC60870-5-103 and MODBUS

understandable by numbers of relay testing

is default. The relay auto detect IEC-60870-5-

units for play back.

COMTRADE

Format

which

is

103 and MODBUS command and respond in


respective language. There is no any specific
setting which define protocol. (Please note
MODBUS by design do not support event
functionality)
Apart from basic protection functions. Relay is
continuously monitors all substations operation
through status, it internal functions, internal
hardware etc. if any changed is observed it
marked as event. Such type of events is stored
in internal non-volatile memory along with time
stamped. Following some of the events. Relay
PKP, Relay Reset, CB Trip, CB close, Changed
of any digital status input, Relay setting
changed etc. Up to 5000 such event can be
stored and can be download for detailed
analysis. Apart from Event record Relay also
record actual waveform of current and voltage
along with all digital and logical status during
fault condition. Up to 10 such waveforms can be
recorded, the duration of disturbance record is
3sec. The disturbance record can be trigger
from physical status input as well as from

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 6 / 16

ASHIDA Numerical Directional 3OC + 1EF


Protection Relay

Type: ADR245B
( AD I T Y A V 2 S e r i e s )
(Preliminary)

Following as some of software clips


All The data can view at time

All The data can view at time


Event list with real time

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 7 / 16

ASHIDA Numerical Directional 3OC + 1EF


Protection Relay

Type: ADR245B
( AD I T Y A V 2 S e r i e s )
(Preliminary)

The waveform and logical and physical status latched by relay can be view and analysed
Data can be viewed as raw sine wave

or RMS value

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 8 / 16

Type: ADR245B

ASHIDA Numerical Directional 3OC + 1EF

( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

While Ordering Specify the following Information for ADR245B Relay

Definition of Model No of Aditya Series of Relays

AM XXXXX XX XX XX XXXX
Communication protocol
02=IEC03+MODBUS

Sub Type
330= NUMERICAL 3OC+1EF
IDMT DIRECTIONAL RELAY

PT Secondary
01= 63.5 VAC
CT Secondary

03 = 1 Amp. / 5 Amp. Selectable


C a b i n e t Size

Auxiliary Supply
08 = 18 250 V dc

05=CSD-H (282 X 138MM)

C a b i n e t Type
01 = Non-drawout
Ordering information:
A

ADR245B AM330050108030102
Type: ADR245B with IEC103 Communication Protocol
Cabinet Size: CSD-H (282 x 138 MM)
Cabinet Type : Non-drawout
Auxiliary Supply: 18-250Vdc
C T s e c :1Amp. / 5Amp. Selectable

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 9 / 16

ASHIDA Numerical Directional 3OC + 1EF

Type: ADR245B
( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

Technical Specifications:
General specifications
Sr. No. Specification

Particulars

I.

Current Input

: Suitable for CT secondary 5Amp. Or 1Amp. site selectable

II.

Aux. Supply

: 18 250VDC to be specified

III.

VA burden on CT

: Less than 0.2VA

IV.

VA burden on Aux.

: Less than 10 Watts

V.

VA burden on PT

: Less than 0.2 VA

VI.

Operating Temp. range

: -10 deg. To + 65 deg.

VII.

Continuous carrying capacity

: 2 x of rated for CT and 1.5 x of rated for PT

VIII.

Pick up

: Within 1.1 times of set value.

IX.

Reset Value

: 95% to 90% of pick up.

X.

Output Contact

: 11 for General Programmable

XI.

Contact Rating

: Continuous: 5A
: Make & carry for 0.5 sec : 30A
: Make & carry for 3 sec : 15A

XII.

Opto Isolated input

: 1 for CB NO & 1 for CB NC


: 10 as general programmable

XIII.

Thermal Withstand for CT

: 20 x of rated for 3.0 sec.

XIV.

Numbers of Event

:5000

General Setting
XV.

Settings

: Unit ID

1 250 in steps of 1

: Baud Rate

1200 57600

: Com Port

RS232 / RS485

: Set Parity

None / Even / Odd

: Freq Select

50Hz 60Hz

: Grp Selection

G1 / G2

: BF Enable

Int / Ext / Byp

: Extbf_I

10 200%

: BF Delay

100 2000 msec in steps of 10msec

: OC CT Sec

1Amp. / 5Amp.

: OC CT Primary

10 2000 in steps of 1

: EF CT Sec

1Amp. / 5Amp.

: EF CT Primary

10 2000 in steps of 1

: PT Primary

1KV 400KV in steps of 1KV

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 10 / 16

ASHIDA Numerical Directional 3OC + 1EF

Type: ADR245B
( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

: Local Control

YES / NO

: Trip Ckt Test

YES / NO

: R Angle Offset

00 359 in steps of 1

: Y Angle Offset

00 359 in steps of 1

: B Angle Offset

00 359 in steps of 1

: Test I R

0.5 2.0 in steps of 0.1

: Test I Y

0.5 2.0 in steps of 0.1

: Test I B

0.5 2.0 in steps of 0.1

: Post Trigger

10% 90% in steps of 1%

Phase Section (Ip)


XVI.

Phase (OC G1 )

: IP1> Enable

OFF/+Dir/-Dir/NDir

: IP1> Settings

10% 250% in steps of 1%.

: IP1> Time Multiplier


(TMS)

x0.02 x1.00 in steps of 0.01

: IP1> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6)

: IP1> C6 Delay

0 1899.9 Sec in steps of 0.1Sec.

: IP2> Enable

OFF/+Dir/-Dir/NDir

: IP2> Settings

10% 250% in steps of 1%

: IP2> Time Multiplier


(TMS)

x0.02 x1.00 in steps of 0.01

: IP2> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6)

: IP2> C6 Delay

0 1899.9 Sec in steps of 0.1Sec.

: IP>> Enable

OFF/+Dir/-Dir/NDir

: IP>> Settings

10% 250% in steps of 1%

: IP>> Time Multiplier


(TMS)

x0.02 x1.00 in steps of 0.01

: IP>> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6)

: IP>> C6 Delay

0 99.99 Sec in steps of 0.1Sec.

: IP>>> Enable

OFF/+Dir/-Dir/NDir

: IP>>> Settings

50% 3000% in steps of 10%

: IP>>> C6 Delay

0 90.00 Sec in steps of 0.01Sec.

: MTA Settings

0 360 Lead in steps of 5

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 11 / 16

ASHIDA Numerical Directional 3OC + 1EF

Type: ADR245B
( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

External Earth Fault Section (Ie)


XVII.

EF G1

: IE> Enable

OFF/+Dir/-Dir/NDir

: IE> Settings

5% 80% in steps of 1%

: IE> Time Multiplier


(TMS)

x0.02 x1.00 in steps of 0.01.

: IE> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6)

: IE> C6 Delay

0 99.9 Sec in steps of 0.1Sec.

: IE>> Enable

OFF/+Dir/-Dir/NDir

: IE>> Settings

5% 80% in steps of 1%

: IE>> Time Multiplier


(TMS)

x0.02 x1.00 in step of 0.01.

: IE>> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6 )

: IE>> C6 Delay

0 99.9 Sec in steps of 0.1Sec.

: IE>>> Enable

OFF/+Dir/-Dir/NDir

: IE>>> Settings

50% 1200% in steps of 10%

: IE>>> C6 Delay

0 3.00 Sec in steps of 0.01Sec.

Internally derived Earth Fault Section (3Io)


XVIII.

3Io G1

: 3Io> Enable

OFF/+Dir/-Dir/NDir

: 3Io> Settings

10% 100% in steps of 1%

: 3Io> Time Multiplier


(TMS)

x0.02 x1.00 in step of 0.01.

: 3Io> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6)

: 3Io> C6 Delay

0 99.9 Sec in steps of 0.1Sec.

: 3Io>> Enable

OFF/+Dir/-Dir/NDir

: 3Io>> Settings

10% 100% in steps of 1%

: 3Io>> Time Multiplier


(TMS)

x0.02 x1.00 in step of 0.01.

: 3Io>> Curve

C1 C6

(Operating Time)

( IDMT curve C1 C5 or Define Time C6)

: 3Io>> C6 Delay

0 99.9 Sec in steps of 0.1Sec.

: 3Io>>> Enable

OFF/+Dir/-Dir/NDir

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 12 / 16

ASHIDA Numerical Directional 3OC + 1EF

Type: ADR245B
( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

: 3Io>>> Settings

50% 1200% in steps of 10%

: 3Io>>> C6 Delay

0 3.00 Sec in steps of 0.01Sec.

: MTA Settings

0 360 Lag in steps of 5

Negative Phase sequence Element (46)`Section


XIX.

NPS G1

: I2>> Enable

YES / NO

: I2>> Settings

10% 100% in steps of 1%

: I2>> Time Multiplier


(TMS)

x0.02 x1.00 in step of 0.01.

: I2>> Curve

C1 C6

(Operating Time)

Additional Data

( IDMT curve C1 C5 or Define Time C6


)

: I2>> C6 Delay

0 99.9 Sec in steps of 0.1Sec.

: I2>>> Enable

YES / NO

: I2>>> Settings

50% 1500% in steps of 10%

: I2>>> C6 Delay

0 3.00 Sec in steps of 0.01Sec.

: C1

Std. Inverse. 1 (3.0S)

: C2

Std. Inverse 2 (1.3S)

: C3

Very Inverse

: C4

Extremely inverse

: C5

Long Time Inverse

: C6

Define Time
(00 99 Sec In steps of 1.0s.)

Under / Over voltage Section (V< / V>)


XX.

Under Voltage (V<)

Over Voltage (V>)

: UV Enable

YES / NO

: UV Setting

25% 95% in steps of 1%

: Operating Time

0.1 10.0 sec in steps of 1sec

: OV Enable

YES / NO

: OV Setting

105% 155% in steps of 1%

: Operating Time

0.1 10.0 sec in steps of 1sec

Neutral Displacement Voltage Protection (NDV)


XXI.

Neutral Displacement
Voltage

: NDV Enable

YES / NO

: NDV Ext/Int

Int/Ext

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 13 / 16

Type: ADR245B

ASHIDA Numerical Directional 3OC + 1EF

( AD I T Y A V 2 S e r i e s )

Protection Relay

(Preliminary)

: Setting

5.5 20V in steps of 1

: Timing

0 10 sec. in steps of 1sec

: Numbers of shot

04

: Dead Time 1, 2 , 3, 4

0.10S 180.00s in steps of 0.1s

: Relaim Time

200 300s in steps of 1s

Auto Recloser Section


XXII.

Auto Recloser

/ 0 = bypass

Operational Indicators (Flags)


XXIII.

PROT.H /ERR

: Green LED indicates Relay OK (Protection Healthy)


: Red LED indicates Fault in following conditions.
1. Problem in relay Hardware.
2. Trip Circuit Faulty.

XXIV.

L2, L3, L4, L5, L6, L7 &


L8

: Spare LEDs Programmable

Drawing References

: For Cabinet Type

- MAC01914

: For Back Connections

- ADV02409

: For Typical External connection

- ADV02314

The Relay Confirm to following standard


Sr. No.

Title

Standard no.

Electromagnetic Compatibility Type Test:


1.

High Frequency Test

: IEC 60255-22-1, class III


: Frequency : 1MHz Damped Oscillatory
: Longitudinal :5 KV (peak)
: Duration: sec duration 2 sec.
: Between input current Terminal

2.

Electrostatic Discharge
Direct Application

: IEC 60255-22-2 Class III and IEC 61000-4-2 class III.


: Contact discharge: 6kV,
: Air discharge: 8KV
: Polarity: both +ve and Ve polarities.

3.

Indirect Application

4.

Fast Transient
Disturbance

: IEC-61000-4-2, Class-III
: IEC 60255-22-4 and IEC 61000-4-4, class A
: 1.2KV; 5/50ns; 5KHz burst duration = 15ms.
: Repetition rate 300ms; Both polarities; Ri = 50; duration 1 min.

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 14 / 16

ASHIDA Numerical Directional 3OC + 1EF


Protection Relay

Type: ADR245B
( AD I T Y A V 2 S e r i e s )
(Preliminary)

: IEC 60255-22-5 / IEC 61000-4-6 class 4


5.

Surge Immunity Test

: Differential Mode = 2kV


: Common Mode = 4kV
: 1.2/50uS , 5 surges of each polarity

6.

Power Frequency
Immunity Test

: IEC-60255-22-7, Class-A

7.

Power Frequency
Magnetic Field Test

: IEC-61000-4-8, Class-V

8.

Radiated
Electromagnetic Field
Disturbance

: IEC- 60255-22-3

Conducted Disturbance
Induced By Radio
Frequency Field

: IEC 60255-22-6 / IEC 61000-4-6: 1996.

10.

AC Ripple In DC
Supply Test

: IEC 60255-11

11.

Radiated Emission

: IEC- 60255-25

9.

: EN-61000-4-3
: Frequency 80MHz 1GHz
: Freq. 150kHz 80MHz, Amplitude 10 V, Modulation 80% AM @
1 KHz

Insulation Tests:
12.

High Voltage Test

: IEC 60255-5. class III


: At 2.5kV 50Hz between all terminal connected together and
earth for 1 minutes

13.

Impulse Voltage Test

: IEC60255-5. class III


: Test voltage: 5KV (peak) 1.2 / 50us,
: Energy :0.5 J,
: Polarity : + ve and Ve
: Nos. of impulses : 3 positive and 3 negative impulse
: Duration between Impulses : 5 sec.

Environmental tests:
14.

Cold test Storage test

: IEC-60068-2-1

15.

Dry heat test

: IEC-60068-2-2

16.

Damp heat test, steady


state

: IEC-60068-2-3

17.

Damp heat test, cyclic

: IEC-60068-2-30

CE compliance
18.

Immunity

: IEC-60255-26

19.

Emissive Test

: IEC- 60255-26

20.

Low voltage directive

: EN-50178

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 15 / 16

ASHIDA Numerical Directional 3OC + 1EF


Protection Relay

Type: ADR245B
( AD I T Y A V 2 S e r i e s )
(Preliminary)

Mechanical tests
: IEC 60255-21-1 class 1
21.

Vibration

: Frequency Range = 10Hz 150Hz, acceleration. = 1gn (9.8


m/s2)
: Sweep rate 1 octave/min; 20 cycle in 3 orthogonal axis.

22.

Bump Test

: IEC 60255-21-2 Class-1


: 1000 bumps of 10gn peak acceleration and 16ms pulse duration
in each of the two opposite direction per axis as per IEC6025521-2 class 1 No. of axes . 3.

23.

Shock Withstand

: IEC 60255-21-2 Clas-1


: 3 shocks of 15gn peak acceleration and 11ms pulse in each of
two opposite direction. No. of axis : 3

24.

Seismic Test

: IEC 60255-21-3
: In single axis sine sweep in X-axis
sweep (@a sweep rate of 1 octave/minute) vibration in the
frequency range (5-40 Hz) at amplitude of 3.5mm or 1.0gn
(whichever is less)
: In single axis sine sweep in Y-axis
- sweep (@a sweep rate of 1 octave/minute) vibration in the
frequency range (5-40 Hz) at amplitude of 1.5mm or 0.5gn
(whichever is less)

Revision Note

Rev. No.
01

Date
15.10.2009

Description
Original specifications

02

01.02.2010

Photograph of the Relay update

03

19.03.2010

IEC61850 option Added

04

26.10.2010

IDMT option added in UV/OV and NDV settings

05

27.06.2011

Back Terminal Arrangement Modified

06

24.04.2012

Back Terminal Arrangement Modified

07

15.09.2012

Event Record increased from 100 to 5000.


Modbus Protocol add
In Monitoring Functions (Event, Disturbance Record):Description of protocol is added

08

17.05.2013

BF setting revised.

09

17.09.2013

Technical information modified

10

15.11.2013

Cabinet Box & Back Terminal details Modified

Note: Due to our policy to upgrade our products constantly, we reserve the right to
supply products which may vary slightly from that indicated above.
ASHIDA ELECTRONICS PVT LTD.

ASHIDA HOUSE, Plot No. A-308, Road No. 21,


Wagle Industrial Estate,Thane (W)-400 604. INDIA.
E-mail: [email protected]
Web: www.ashidaelectronics.com

Ref.:ADR245B_V2
Issue: 10 15.11.2013
Page 16 / 16

You might also like