Pve27 2 Parte

Download as pdf or txt
Download as pdf or txt
You are on page 1of 4

Service Data

Vickers

Piston Pumps

Heavy Duty Piston Pump


PVE27*-E2-21-C**-20

Revised 4/1/85

M-2241-S

676584 C Pressure
compensator S/A
preset at 250 bar.

: 1489 Nut
: 582544 Adj. Screw
: 1497 Nut

: 676561 Plug

: 676180 Adj. Screw


: 1489 Nut
: 582544 Adj. Screw

: 627375 Spring Seat

: 676591 Spring Seat

: 170160 O-Ring

: 676561 Plug

: 197590
Back-Up Ring

: 627375 Spring Seat

: 154010 O-Ring

: 170160 O-Ring

: 628273 Spring
(300 PSI)

: 631529 Spring

: 676586 Spring Guide

: 627374 Spring Guide

: 181728 Plug
Torque 40-45 N.m
(30-33 lb. ft.)

: 676578 Body
: 627373 Spool
: 298126 Screw
(4 reqd)
Torque 31-37 N.m
(23-28 lb. ft.)
: 154128 O-Ring
: 627391 Plug
Torque 18-20
N.m
(13-15 lb. ft.)

: 631529 Spring
: 627374 Spring Guide
: 676579 Body
: 177969 O-Ring (3 reqd)

: 154128 O-Ring
(2 reqd)

: 627373 Spool (Press. Limiter)


: 154128 O-Ring (3 reqd)

: 177969 O-Ring
(3 reqd)

: 627391 Plug (3 reqd)


Torque 18-20 N.m
(13-15 lb. ft.)

: 298126 Screw
(4 reqd)
Torque 31-37 N.m
(23-28 lb. ft.)
: 676585 Spool
(Load Sensing)
584455 Spring

J 680624 Spring Guide

402644 Poppet
186580 Plug
Torque 54-59 N.m
(40-40.3 lb. ft.)

J 680625 Cylinder
Block

402643 Seat
580532 Pin
(2 reqd)

Y 396098 O-Ring
Valve Block
(See table)
(Refer to table
on back page
for thru-drive
valve blocks)

J 627524 Spring

214688 Screw (6 reqd)


Torque 50-55 N.m
(36.8-40.5 lb. ft.)

Valve Plate (See table)


Bronze surface must
face Cylinder Block

214684 Screw (2 reqd)


Torque 50-55 N.m
(36.8-40.5 lb. ft.)

926258 Shaft Spacer Kit

227401 Screw (2 reqd)


404751 Rotation Plate

J 584524 Spring Guide


J 85560 Retaining Ring

989704 Bearing S/A


Y 396094 O-Ring
(3 reqd)
189087 Plug (3 reqd)
Torque 15-16 N.m
(11-12 lb. ft.)

248935 Pin

PVE27*-E2-21-C**-20

676580 CVP Load Sensing/


Pressure limiter compensator S/A. Shipped preset at
approximately: Load sensing
differential pressure 20 bar.
Pressure limiter 250 bar.

409857 Cover (2 reqd)

676590 Housing

164881 Screw (8 reqd)


Torque 15-17 N.m
(11-12 lb. ft.)

Y 597022 Gasket
366865 Bearing S/A

Y 589953 O-Ring
(2reqd)
597032 Spacer
(2 reqd)

597033 Key
627593 Yoke S/A
392059 Pin

103824 Retaining Ring

J 584515 Swash Plate


J 584512 Shoe Cage
J 632587 Spacer

Y 627484 Shaft Seal


(Spring faces inward)

680608 Shaft

227376 Screw (2 reqd)


Nameplate
353187 Bearing S/A (2 reqd)
J 926257 Piston Kit
(Includes 9 Piston
and Shoe S/A)

zY 154130 O-Ring
z 584510 Control Stem
Torque 75-83 N.m
(55-61 lb. ft.)
z 584511 Control Piston

926259 Pintle Shim Kit


(Refer to Pintle Brg.
preload in overhaul
manual)
F 634470 Bias Piston

Y Included in
920267 Seal Kit

F 634499 Spring
F 584485 Bias Piston Rod
Torque 75-83 N.m
(55-61 ft. lb.)
FY 154130 O-Ring

F Included in 926450
Bias Piston Kit
J Included in 938102
rotating group
z Included in 926449
Control Piston Kit

: Individual parts not


available for sale. Order
complete subassembly.
Valve
Valve
Plate
Block
680786 680630
680785 680631

Shaft
Rotation
CCW Left
CW Right

Note
Parts are shown for left hand shaft
rotation. The position of control and
bias pistons are reversed for right
hand rotation. (Assemble using
Loctite 270.

Model Code

Model Series

Input Shaft

Pump Design

Control Type

Control Design

PVE - Pump, variable, inline series E


2

Flow Rating in USgpm


(at 1800 RPM)

27 - 27 USgpm

Shaft Rotation
(Viewed from Shaft End)

CPressure compensator
CVP - Load sensing with pressure
limiter

R - Right hand (CW)


L - Left hand (CCW)
4

Ports and Configuration

E - Rear ports
Omitted - Side ports, flanged standard

For satisfactory service life of these components, use full flow filtration to provide fluid which meets ISO cleanliness code
20/18/15 or cleaner. Selections from Eaton OFP,OFR and OFRS filter series are recommended.
Printed in U.S.A.

You might also like