Peres 10PPS103 2 Electrical Machines PDF

ELECTRICAL GENERATORS USED FOR WIND POWER GENERATION
The mechanical power of a wind turbine is converted into electric power by an

alternating current (AC) generator or a direct current (DC) generator. The AC generator
can be either a synchronous machine or an induction machine, the latter being the most
widely used in the wind power industry. The electrical machine works on the principle of
action and reaction of electromagnetic induction. The resulting electromechanical energy
conversion is reversible. The same machine can be used as a motor for converting electric
power into mechanical power or as a generator for converting mechanical power into
electric power.
Figure 1 depicts common construction features of electrical machines. Typically,
there is an outer stationary member (stator) and an inner rotating member (rotor). The
rotor is mounted on bearings fixed to the stator. Both the stator and the rotor carry
cylindrical iron cores, which are separated by an air gap. The cores are made of magnetic
iron of high permeability and have conductors embedded in slots distributed on the core
surface. Alternatively, the conductors are wrapped in the coil form around salient
magnetic poles. Figure 2 is a cross-sectional view of a rotating electrical machine with
the stator made of salient poles and the rotor with distributed conductors. The magnetic
flux, created by the excitation current in one of the two coils, passes from one core to the
other in a combined magnetic circuit always forming a closed loop. Electromechanical
energy conversion is accomplished by interaction of the magnetic flux produced by one
coil with the electrical current in the other coil. The current may be externally supplied or
electromagnetically induced. The induced current in a coil is proportional to the rate of
change in the flux linkage of that coil.
The various types of machines differ fundamentally in the distribution of the
conductors forming the windings, and by their elements: whether they have continuous
slotted cores or salient poles. The electrical operation of any given machine depends on
the nature of the voltage applied to its windings. The narrow annular air gap between the
stator and the rotor is the critical region of the machine operation, and the theory of
performance is mainly concerned with the conditions in or near the air gap.
www.ravivarmans.hpage.com
DC GENERATOR
All machines in the internal working are AC machines, because the conductors
rotate in the magnetic flux of alternate north and south poles. The DC machine converts
the inside AC into DC for outside use. It does so by using a mechanical commutator. The
commutator performs this function by sliding carbon brushes along a series of copper
segments. It switches the positive output terminal continuously to the conductor

generating the positive polarity voltage, and likewise for the negative polarity terminal.
The sliding contacts inherently result in low reliability and high maintenance cost.
Despite this disadvantage, the DC machine was used extensively as a motor until the
early 1980s because of its extremely easy speed control. It has been used as a generator in
a limited number of wind power installations of small capacity, particularly where the
electricity could be locally used in the DC form. However, the conventional DC machine
with a mechanical commutator and sliding carbon brushes has fallen out of favor in the
present day. Its brushless version is used where the DC machine gives a system
advantage.
The conventional DC machine is either self-excited by shunt or by series coils
carrying DC current to produce a magnetic field. The modern DC machine is often
designed with permanent magnets to eliminate the field current requirement, hence, the
commutator. It is designed in the inside-out configuration. The rotor carries the
permanent-magnet poles and the stator carries the wound armature. The stator produces
AC current, which is then rectified using the solid-state semi conducting devices. Such a
machine does not need the commutator and the brushes; hence, the reliability is greatly
improved. The permanent-magnet DC machine is used with small wind turbines.
However, due to limitations of the permanent-magnet capacity and strength, the brushless
DC machine is generally limited to ratings below 100 kW.
SYNCHRONOUS GENERATOR
The synchronous generator produces most of the electric power consumed in the
world. For this reason, the synchronous machine is an established machine. The machine
works at a constant speed related to the fixed supply frequency. Therefore, it is not well
suited for variable-speed operation in wind plants without power electronic frequency
converters. Moreover, the conventional synchronous machine requires DC current to
excite the rotor field, which has traditionally used sliding carbon brushes on slip rings on
the rotor shaft. This introduces some unreliability in its use. The modern synchronous
machines are made brushless by generating the required DC field current on the rotor
itself. Reliability is greatly improved while reducing the cost. The DC field current need
can be eliminated altogether by using a reluctance rotor, in which the synchronous

operation is achieved by the reluctance torque. The reluctance machine rating, however,
is limited to tens of kW. It is being investigated at present for small wind generators.
The synchronous machine, when used in a grid-connected system, has some
advantages over the induction machine. It does not require reactive power from the grid.
This results in a better quality of power at the grid interface. This advantage is more
pronounced when the wind farm is connected to a small-capacity grid using a long lowvoltage transmission link.
The synchronous generator is rarely used in gear-driven wind systems. However,
the low-speed design of the synchronous generator is often found advantageous in the
direct-drive variable-speed wind turbine. In such a design, the generator is completely
decoupled from the grid by a voltage source power electronic converter connected to the
stator, and the rotor is excited by an excitation winding or a permanent magnet.
INDUCTION GENERATOR
The electric power in industry is consumed primarily by induction machines
working as motors driving mechanical loads. For this reason, the induction machine,
invented by Nikola Tesla and financed by George Westinghouse in the late 1880s,
represents a well-established technology. The primary advantage of the induction
machine is the rugged brushless construction that does not need a separate DC field
power. The disadvantages of both the DC machine and the synchronous machine are
eliminated in the induction machine, resulting in low capital cost, low maintenance, and
better transient performance. For these reasons, the induction generator is extensively
used in small and large wind farms and small hydroelectric power plants. The machine is
available in numerous power ratings up to several megawatts capacity, and even larger.
For economy and reliability, many wind power systems use induction machines as
electrical generators.
CONSTRUCTION OF INDUCTION GENERATOR

In the electromagnetic structure of the induction generator, the stator is made of
numerous coils wound in three groups (phases), and is supplied with three-phase current.
The three coils are physically spread around the stator periphery and carry currents,
which are out of time phase. This combination produces a rotating magnetic field, which
is a key feature in the working of the induction machine. The angular speed of the
rotating magnetic field is called the synchronous speed. It is denoted by N s and is given
by the following in rpm
Ns
120 f
p
(1)
Where f = frequency of the stator excitation

p= Number of magnetic poles.
The stator coils are embedded in slots in a high-permeability magnetic core to
produce the required magnetic field intensity with a small exciting current. The rotor,
however, has a completely different structure. It is made of solid conducting bars, also
embedded in slots in a magnetic core. The bars are connected together at both ends by
two conducting end rings (Figure 3). Because of its resemblance, the rotor is called a
squirrel cage rotor, or the cage rotor, for short, and the motor is called the squirrel cage
induction motor.
WORKING PRINCIPLE
The stator magnetic field is rotating at the synchronous speed determined by
Equation 1. This field is conceptually represented by the rotating magnets in Figure 3.
The relative speed between the rotating field and the rotor induces the voltage in each
closed loop of t
of the
induced voltage is given by Faradays law of electromagnetic induction, namely:

e
Where
d
dt
( 2)
=the magnetic flux of the stator linking the rotor loop.

This voltage in turn sets up the circulating current in the rotor. The
electromagnetic interaction of the rotor current and stator flux produces the torque. The
magnitude of this torque is given by the following:
The rotor accelerates under this torque. If the rotor were on frictionless bearings
in a vacuum with no mechanical load attached, it would be completely free to rotate with
zero resistance. Under this condition, the rotor would attain the same speed as the stator
field, namely, the synchronous speed. At this speed, the current induced in the rotor is
zero, no torque is produced, and none is required. Under these conditions, the rotor finds
equilibrium and will continue to run at the synchronous speed.
If the rotor is now attached to a mechanical load such as a fan, it will slow down.
The stator flux, which always rotates at a constant synchronous speed, will have a relative
speed with respect to the rotor. As a result, electromagnetically induced voltage, current,
and torque are produced in the rotor. The torque produced must equal that needed to drive
the load at this speed. The machine works as a motor in this condition.
If we attach the rotor to a wind turbine and drive it faster than its synchronous
speed via a step-up gear, the induced current and the torque in the rotor reverse the
direction. The machine now works as the generator, converting the mechanical power of
the turbine into electric power, which is delivered to the load connected to the stator
terminals. If the machine were connected to a grid, it would feed power into the grid.
Thus, the induction machine can work as an electrical generator only at speeds higher
than the synchronous speed. The generator operation, for this reason, is often called the
super synchronous operation of the induction machine.
As described in the preceding text, an induction machine needs no electrical
connection between the stator and the rotor. Its operation is entirely based on
electromagnetic induction; hence, the name. The absence of rubbing electrical contacts
and simplicity of its construction make the induction generator a very robust, reliable,
and low-cost machine. For this reason, it is widely used in numerous industrial
applications.
Engineers familiar with the theory and operation of the electrical transformer
would see the working principle of the induction machine can be seen as the transformer
with shorted secondary coil. The high-voltage coil on the stator is excited, and the lowvoltage coil on the rotor is shorted on itself. The electrical or mechanical power from one
to the other can flow in either direction. The theory and operation of the transformer,
therefore, holds true when modified to account for the relative motion between the stator
and the rotor. This motion is expressed in terms of the slip of the rotor relative to the
synchronously rotating magnetic field.
ROTOR SPEED AND SLIP

The slip of the rotor is defined as the ratio of the speed of rotating magnetic field
sweeping past the rotor and the synchronous speed of the stator magnetic field as follows:
The slip is positive in the motoring mode and negative in the generating mode. In both
modes, a higher rotor slip induces a proportionally higher current in the rotor, which
results in greater electromechanical power conversion. In both modes, the value of slip is
generally a few to several percent. Higher slips, however, result in greater electrical loss,
which must be effectively dissipated from the rotor to keep the operating temperature
within the allowable limit.
The heat is removed from the machine by the fan blades attached to one end ring
of the rotor. The fan is enclosed in a shroud at the end. The forced air travels axially
along the machine exterior, which has fins to increase the dissipation area.
The induction generator feeding a 60-Hz grid must run at a speed higher than
3600 rpm in a 2-pole design, 1800 rpm in a 4-pole design, and 1200 rpm in a 6- pole
design. The wind turbine speed, on the other hand, varies from a few hundred rpm in kWrange machines to a few tens of rpm in MW-range machines. The wind turbine, therefore,
must interface the generator via a mechanical gear. As this somewhat degrades efficiency
and reliability, many small stand-alone plants operate with custom-designed generators
operating at lower speeds without any mechanical gear.
Under the steady-state operation at slip s, the induction generator has the
following operating speeds in rpm:
Thus, the squirrel cage induction machine is essentially a constant-speed machine,

which runs slightly slipping behind the rotating magnetic field of the three phase stator
current. The rotor slip varies with the power converted, and the rotor speed variations are
within a few percent. It always consumes reactive power undesirable when connected
to a weak grid which is often compensated by capacitors to achieve the systems power
factor closed to one. Changing the machine speed is difficult. It can be designed to run at
two different but fixed speeds by changing the number of poles of the stator winding.
The voltage usually generated in the induction generator is 690-V AC. It is not
economical to transfer power at such a low voltage over a long distance. Therefore, the
machine voltage is stepped up to a higher value between 10,000 V and 30,000 V via a
step-up transformer to reduce the power losses in the lines.
SELF EXCITATION OF INDUCTION GENERATOR (SEIG)

The IG with capacitor excitation is driven by a prime mover with the main power
switch open (Figure 4(a)). As the speed increases, due to prime-mover torque, eventually,
the no-load terminal voltage increases and settles to a certain value, depending on
machine speed, capacitance, and machine parameters.
Figure (4) Self-excitation on self-excited induction generator (SEIG):

(a) The general scheme, (b) oversimplified equivalent circuit, and
(c) quasi-steady-state self-excitation characteristics.
The equivalent circuit is further simplified by neglecting the stator resistance and
leakage inductance and by considering zero slip (s=0 open rotor circuit) for no-load
conditions (Figure 4.3(b)).E rem represents the no-load initial stator voltage (before self-
excitation), at frequency at frequency
10
, produced by the remnant flux density in
the rotor left there from previous operation events.

To initiate the self-excitation process, E rem has to be nonzero. The magnetization
curve of the IG, obtained from typical motor no-load tests, E 1 (I m) has to advance to the
nonlinear (saturation) zone in order to firmly intersect the capacitor straight-line voltage
characteristic (Figure 4.(c)) and, thus, produce the no-load voltage E 1 .The process of selfexcitation of IG has been known for a long time.
The increasing of the terminal voltage from Vrem toV 10 unfolds slowly in time
(seconds), and Figure 4(c) presents it as a step-wise quasi-steady-state process. It is a
qualitative representation only. Once the SEIG is self-excited, the load is connected. If
the load is purely resistive, the terminal voltage decreases and so does (slightly) the
frequency
<
With
for constant (regulated) prime-mover speed
, the SEIG delivers power to the load for negative slip S<0
np
f1
;S 0
1 S
The computation of terminal voltage V1 , frequency f1 , stator current I 1 , delivered
1
active and reactive power (efficiency) for given load (speed n), capacitor C, and machine
parameters, R1 ,R 2 ,L1l ,L2l ,L m(I m ) represents, in fact, the process of obtaining the steadystate performance. The nonlinear function L m(I m ) magnetization curve and the
variation of frequency f1 with load, at constant speed n, make the process mathematically
intricate.
Steady-State Analysis of Three-Phase SEIGs

Various analytical (and numerical) methods to calculate the steady-state
performance of SEIGs were proposed. They seem, however, to fall into two main
categories:
Loop impedance models
Nodal admittance models
Both models are based on the SEIG equivalent circuit (Figure 5) expressed in per unit
(P.U.) form for frequency f (P.U.) and speed U (in P.U.) as follows:
f
f1
;
f1b
np1
;
f1b
The base frequency for which all reactances X 1l , X 2 l , X m ( I m ) are calculated is f1b
With an R L , L L , C L load, the equivalent circuit in Figure 5 with speed and frequency in
P.U. terms becomes as shown in Figure 6.
The presence of frequency f in the load, the dependence of core loss resistance R m
of frequency f, and the nonlinear dependence on X m of I m makes the solving of the
equivalent circuit difficult. The SEIG plus load show zero total impedance:
R e (IG+load) =0
X e (IG+excitation_capacitor+load) =0
for self-excitation, under load.
To solve it simply, the problem is reduced to two unknowns: f (frequency) and X m for
given excitation capacitor, IG (R 1 , R 2, X 1l , X 2 l , X m ( I m ) ), load (R L , X L , X c), and speed U
High-order polynomial equation (in f) approaches.
Optimization approaches.
2.4.1 Second-Order Slip Equation Methods
The standard equivalent circuit of Figure 6 may be changed by lumping together the IG
stator
(R 1 , jfX 1l ),
( RL , jfX L , j
X 1L
the
excitation
capacitor
reactance (
jX c
),
f
and
the
load
X CL
) into an equivalent series circuit ( R1L , jfX 1L ) .For self-excitation,
f
The Analysis and Modelling

of a Self-excited Induction
Generator Driven by a
Variable Speed Wind Turbine
1. Introduction
Induction machine is used in a wide variety of applications as a means of converting electric
power to mechanical work. The primary advantage of the induction machine is its rugged
brushless construction and no need for separate DC field power. These machines are very
economical, reliable, and are available in the ranges of fractional horse power (FHP) to multi
megawatt capacity. Also, unlike synchronous machines, induction machines can be
operated at variable speeds. For economy and reliability many wind power systems use
induction machines, driven by a wind turbine through a gear box, as an electrical generator.
The need for gearbox arises from the fact that lower rotational speeds on the wind turbine
side should be converted to high rotor speeds, on the electrical generator side, for electrical
energy production.
There are two types of induction machine based on the rotor construction namely, squirrel
cage type and wound rotor type. Squirrel cage rotor construction is popular because of its
ruggedness, lower cost and simplicity of construction and is widely used in stand-alone
wind power generation schemes. Wound rotor machine can produce high starting torque
and is the preferred choice in grid-connected wind generation scheme. Another advantage
with wound rotor is its ability to extract rotor power at the added cost of power electronics
in the rotor circuit.
This chapter focuses on the electrical generation part of a wind energy conversion system.
After a brief introduction of the induction machine, the electrical generator used in this
chapter, a detailed analysis of the induction machine operated in stand-alone mode is
presented. As a generator, induction machines have the drawback of requiring reactive
power for excitation. This necessitates the use of shunt capacitors in the circuit. The effect of
magnetization inductance on self-excitation of the induction generator is discussed. Also,
this chapter presents the two existing methods to analyze the process of self-excitation in
induction machine and the role of excitation-capacitors in its initiation.
Simulation results of the self-excited induction generator driven by the variable speed wind
turbine are presented in the last section of this chapter. The process of voltage build up and
the effect of saturation characteristics are also explained in the same section.
2. Induction machine
In the electromagnetic structure of the Induction machine, the stator is made of numerous
coils with three groups (phases), and is supplied with three phase current. The three coils
are physically spread around the stator periphery (space-phase), and carry currents which
are out of time-phase. This combination produces a rotating magnetic field, which is a key
feature of the working of the induction machine. Induction machines are asynchronous
speed machines, operating below synchronous speed when motoring and above
synchronous speed when generating. The presence of negative resistance (i.e., when slip is
negative), implies that during the generating mode, power flows from the rotor to the stator
in the induction machine.
2.1 Equivalent electrical circuit of induction machine
The theory of operation of induction machine is represented by the per phase equivalent
circuit shown in Figure 1 (Krause et al., 1994).
Fig. 1. Per-phase equivalent circuit of the induction machine referred to the stator.
In the above figure, R and X refer to the resistance and inductive reactance respectively.
Subscripts 1, 2 and m represent stator, rotor values referred to the stator side and
magnetizing components, respectively.
Induction machine needs AC excitation current for its running. The machine is either selfexcited or externally excited. Since the excitation current is mainly reactive, a stand-alone
system is self-excited by shunt capacitors. In grid-connected operation, it draws excitation
power from the network, and its output frequency and voltage values are dictated by the
grid. Where the grid capacity of supplying the reactive power is limited, local capacitors can
be used to partly supply the needed reactive power (Patel, 1999).
3. Self-Excited Induction Generator (SEIG)

Self-excited induction generator (SEIG) works just like an induction machine in the
saturation region except the fact that it has excitation capacitors connected across its stator
terminals. These machines are ideal choice for electricity generation in stand-alone variable
speed wind energy systems, where reactive power from the grid is not available. The
induction generator will self-excite, using the external capacitor, only if the rotor has an
adequate remnant magnetic field. In the self-excited mode, the generator output frequency
and voltage are affected by the speed, the load, and the capacitance value in farads (Patel,
1999). The steady-state per-phase equivalent circuit of a self-excited induction generator is
shown in the Figure 2.
Fig. 2. Self-excited induction generator with external capacitor.

The process of self-excitation in induction machines has been known for many decades
(Basset & Potter, 1935). When capacitors are connected across the stator terminals of an
induction machine, driven by an external prime mover, voltage will be induced at its
terminals. The induced electromotive force (EMF) and current in the stator windings will
continue to rise until the steady-state condition is reached, influenced by the magnetic
saturation of the machine. At this operating point the voltage and the current will be
stabilized at a given peak value and frequency. In order for the self-excitation to occur, for a
particular capacitance value there is a corresponding minimum speed (Wagner, 1935). So, in
stand-alone mode of operation, it is necessary for the induction generator to be operated in
the saturation region. This guarantees one and only one intersection between the
magnetization curve and the capacitor reactance line, as well as output voltage stability
under load as seen in the Figure 3:
Fig. 3. Determination of stable operation of self-excited induction generator.

At no-load, the capacitor current Ic=V1/Xc must be equal to the magnetizing current
Im=V1/Xm. The voltage V1 is a function of Im, linearly rising until the saturation point of the
magnetic core is reached. The output frequency of the self-excited generator is, f=1/(2 CXm)
and =2 f where C is self-exciting capacitance.
4. Methods of analysis
There are two fundamental circuit models employed for examining the characteristics of a
SEIG. One is the per-phase equivalent circuit which includes the loop-impedance method
adopted by (Murthy et al, 1982) and (Malik & Al-Bahrani, 1990), and the nodal admittance
method proposed by (Ouazene & Mcpherson, 1983) and (Chan, 1993). This method is
suitable for studying the machines steady-state characteristics. The other method is the dqaxis model based on the generalized machine theory proposed by (Elder et al., 1984) and
(Grantham et al., 1989), and is employed to analyze the machines transient state as well as
steady-state.
4.1 Steady-state model
Steady-state analysis of induction generators is of interest both from the design and
operational points of view. By knowing the parameters of the machine, it is possible to
determine the performance of the machine at a given speed, capacitance and load conditions.
Loop impedance and nodal admittance methods used for the analysis of SEIG are both
based on per-phase steady-state equivalent circuit of the induction machine (Figure 4),
modified for the self-excitation case. They make use of the principle of conservation of active
and reactive powers, by writing loop equations (Murthy et al, 1982], (Malik & Al-Bahrani,
1990), (Al-Jabri & Alolah, 1990) or nodal equations (Ouazene & Mcpherson, 1983), (Chan,
1993), for the equivalent circuit. These methods are very effective in calculating the
minimum value of capacitance needed for guaranteeing self-excitation of the induction
generator. For stable operation, excitation capacitance must be slightly higher than the
minimum value. Also there is a speed threshold, below which no excitation is possible,
called as the cutoff speed of the machine. In the following paragraph, of loop impedance
method is given for better understanding.
The per-unit per-phase steady-state circuit of a self-excited induction generator under RL
load is shown in Figure 4 (Murthy et al., 1982), (Ouazene & Mcpherson, 1983).
Fig. 4. Equivalent circuit of self-excited induction generator with R-L Load.

Where:
Rs, Rr, R : p.u. per-phase stator, rotor (referred to stator) and load resistance respectively.
Xls, Xlr, X, Xm : p.u. per-phase stator leakage, rotor leakage (referred to stator), load and
magnetizing reactances (at base frequency), respectively.
Xsmax : p.u. maximum saturated magnetizing reactance.
C : per-phase terminal-excitation capacitance.
Xc : p.u. per-phase capacitive reactance (at base frequency) of the terminal excitation
capacitor.
f, v : p.u.frequency and speed, respectively.
N : base speed in rev/min
Zb : per-phase base impedance
fb : base frequency
Vg, V0 : per-phase air gap and output voltages, respectively.
In the analysis of SEIG the following assumptions were made (Murthy et al., 1982):
1. Only the magnetizing reactance Xm is assumed to be affected by magnetic saturation,
and all other parameters of the equivalent circuit are assumed to be constant. Selfexcitation results in the saturation of the main flux and the value of Xm reflect the
magnitude of the main flux. Leakage flux passes mainly in the air, and thus these fluxes
are not affected to any large extent by the saturation of the main flux.
2. Stator and rotor leakage reactance, in per-unit are taken to be equal. This assumption is
normally valid in induction machine analysis.
3. Core loss in the machine is neglected.
For the circuit shown in Figure 4, the loop equation for the current can be written as:
IZ=0
(1)
Where Z is the net loop impedance given by

Z=
+j
(2)
Since at steady-state excitation I 0, it follows from (equation 1) that Z = 0 , which implies

that both the real and imaginary parts of Z are zeros. These two equations can be solved
simultaneously for any two unknowns (usually voltage and frequency). For successful
voltage-buildup, the load-capacitance combination and the rotor speed should result in a
value such that Xm=Xsmax, which yields the minimum value of excitation capacitance below
which the SEIG fails to self-excite.
4.2 Steady-state and transient model (abc-dq0 transformation)
The process of self-excitation is a transient phenomenon and is better understood if
analyzed using a transient model. To arrive at transient model of an induction generator,
abc-dq0 transformation is used.
4.2.1 abc-dq0 transformation
The abc-dq0 transformation transfers an abc (in any reference frame) system to a rotating dq0
system. (Krause et al., 1994) noted that, all time varying inductances can be eliminated by
referring the stator and rotor variables to a frame of reference rotating at any angular
velocity or remaining stationary. All transformations are then obtained by assigning the
appropriate speed of rotation to this (arbitrary) reference frame. Also, if the system is balanced
the zero component will be equal to zero (Krause et al., 1994).
A change of variables which formulates a transformation of the 3-phase variables of stationary
circuit elements to the arbitrary reference frame may be expressed as (Krause et al., 1994):
Fqdos = Ksfabcs
Where:
Fqdos =
;fabcs =
;Ks =
(3)
is the dummy variable of integration

For the inverses transformation:
In (equation 3), f can represent voltage, current, flux linkage, or electric charge. The
subscript s indicates the variables, parameters and transformation associated with stationary
circuits. This above transformation could also be used to transform the time-varying rotor
windings of the induction machine. It is convenient to visualize the transformation
equations as trigonometric relationships between variables as shown in Figure 5.
Fig. 5. Transformation for stationary circuits portrayed bytrigonometric relationships.

The equations of transformation may be thought of as if the fqs and fds variables are directed
along axes orthogonal to each other and rotating at an angular velocity of , where upon fas,
fbs, and fcs (instantaneous quantities which may be any function of time), considered as
variables directed along stationary paths each displaced by 1200. Although the waveforms of
the qs and ds voltages, currents and flux linkages, and electric charges are dependent upon
the angular velocity of the frame of reference, the waveform of the total power is same
regardless of the reference frame in which it is evaluated (Krause et al., 1994).
4.2.2 Voltage equations in arbitrary reference-frame variables
The winding arrangement for a 2-pole, 3-phase, wye-connected, symmetrical induction
machine is shown in Figure 6.
The stator windings are identical sinusoidally distributed windings, displaced 1200, with Ns
equivalent turns and resistance rs. The rotor is consists of three identical sinusoidally
distributed windings, with Nr equivalent turns and resistance rr. Note that positive a, b, c
sequence is used in both in Figures 5 and 6.
The voltage equations in machine variables can be expressed as (Krause et al., 1994):
Fig. 6. Two-pole, 3-phase, wye connected symmetrical induction machine.

Vabcs = rsiabcs + p
abcs
(4)
Vabcr = rriabcr + p
abcr
(5)
Where:
Subscript s denotes parameters and variables associated with the stator.
Subscript r denotes parameters and variables associated with the rotor.
Vabcs, Vabcr are phase voltages.
Iabcs, Iabcr are phase currents.
,
abcs abcr are the flux linkages and p = d/dt.
By using the abc-dq0 transformation and expressing flux linkages as product of currents and
winding inductances, we obtain the following expressions for voltage in arbitrary reference
frame (Krause et al., 1994):
Vqdos = rsiqdos +
Vqdor = rriqdor + ( -
dqs +
r)
(6)
qdos
(7)
dqr + p qdor
Where:
is the electrical angular velocity of the arbitrary frame.
r is the electrical angular velocity of the rotor.
(
dqs)
=[
ds
qs
0] ; ( dqr)T = [ dr
- qr
0]
"" denotes rotor values referred to the stator side.

Using the relations between the flux linkages and currents in the arbitrary reference frame
and substituting them in (equations 6) & (equations 7), the voltage and flux equations are
expressed as follows:
Vqs = rsiqs +
ds + p qs
(8)
Vds = rsids -
qs
+p
(9)
ds
Vqr = rriqr ( -
r)
dr + p qr
(10)
Vdr = rridr - ( -
r)
qr + p dr
(11)
qs =
Llsiqs + Lm (iqs + i'qr)
(12)
ds =
Llsids + Lm (ids + i'dr)
(13)
qr = Llriqr + Lm (iqs + i'qr)
(14)
dr = Llridr + Lm (ids + i'dr)
(15)
Where:
Lls and Lms are leakage and magnetizing inductances of the stator respectively.
Llr and Lmr are leakage and magnetizing inductances of the rotor respectively.
Magnetizing inductance, Lm = Lms
The voltage and flux linkage equations suggest the following equivalent circuits for the
induction machine:
Fig. 7. Arbitrary reference-frame equivalent circuits for a 3-phase, symmetrical induction

machine
4.2.2.1 Torque equations
The expression for electromagnetic torque, positive for motor operation and negative for
generator operation, in terms of the arbitrary reference variables can be expressed as
(Krause et al., 1994):
For motor action, Te =
For generator action, Te =
m(iqsidr
idsiqr)
m(idsiqr
iqsidr)
(16)
(17)
The torque and speed are related by the following expressions:

For the motor operation, Te-motor = J
For the generator operation, TD = J
TD
(18)
Te-gen
(19)
Where:
P: Number of poles.
J: Inertia of the rotor in (Kg m2).
TD: Drive torque in (Nm).
4.2.3 Stationary reference frame
Although the behavior of the induction machine may be described by any frame of
reference, there are three which are commonly used (Krause et al., 1994). The voltage
equations for each of these reference frames can be obtained from the voltage equations in
the arbitrary reference frame by assigning the appropriate speed to . That is, for the
stationary reference frame,
= 0, for the rotor reference frame,
= r, and for the
synchronous reference frame, = e.
Generally, the conditions of operation will determine the most convenient reference frame
for analysis and/or simulation purposes. The stator reference frame is used when the stator
voltages are unbalanced or discontinuous and the rotor applied voltages are balanced or
zero. The rotor reference frame is used when the rotor voltages are unbalanced or
discontinuous and the stator applied voltages are balanced. The stationary frame is used
when all (stator and rotor) voltages are balanced and continuous. In this thesis, the stationary
reference frame( =0) is used for simulating the model of the self-excited induction generator
(SEIG).
(0)=0 (see (equation 3)), the
In all asynchronously rotating reference frames(
r) with
phasor representing phase a variables (with subscript as) is equal to phasor representing qs
variables. In other terms, for the rotor reference frame and the stationary frame,
fas = fqs , fbs = fas
and fcs = fas
4.2.4 SEIG model
As discussed above, the dq model of the SEIG in the stationary reference frame is obtained
by substituting =0 in the arbitrary reference frame equivalent of the induction machine
shown in Figure 7. Figure 8 shows a complete dq-axis model, of the SEIG with load, in the
stationary reference frame. Capacitor is connected at the stator terminals for the selfexcitation. For convenience, all values are assumed to be referred to the stator side and here
after is neglected while expressing rotor parameters referred to the stator (Seyoum et al.,
2003).
Fig. 8. dq model of SEIG in stationary reference frame (All values referred to stator)
For no-load condition, rearranging the terms after writing loop equations for Figure 8, we
obtain the following voltage equations expressed in the form of a matrix (Krause et al., 1994),
(Seyoum et al., 2003):
(20)
Where:
Kd and Kq are constants representing initial induced voltages along the d-axis and q-axis
respectively, due to the remaining magnetic flux in the core.
Vcqo and Vcdo are initial voltages in the capacitors.
Ls = Lls + Lm and Lr = Llr + Lm.
The above equations can further be simplified in the following manner using (equations 815):
In the stationary reference frame (equations 8) can be written as,
Vqs = -Vcq = rsiqs + 0
ds
(21)
qs
Substituting (equation 12) in (equation 21), will result

(22)
0 = Vcq + rsiqs + Lspiqs + Lmpiqr

Solving for piqr by substituting (equation 14) and (equation 15) in (equation 10) yields:
(23)
Piqr =
Substituting (equation 23) in (equation 22) results in the final expression for iqs as:
)
piqs =
(24)
Where:
L = LsLr Similarly, the expressions for other current components are obtained and the SEIG can be
represented in a matrix form as:
pI = AI + B
Where:
(25)
I=
;Vcq =
; Vcq =
Any combination of R, L and C can be added in parallel with the self-excitation capacitance
to act as load. For example, if resistance R is added in parallel with the self-excitation
capacitance, then the term 1/pC in (equation 20) becomes R/(1+RpC). The load can be
connected across the capacitors, once the voltage reaches a steady-state value (Grantham et
al., 1989), (Seyoum et al., 2003).
The type of load connected to the SEIG is a real concern for voltage regulation. In general,
large resistive and inductive loads can vary the terminal voltage over a wide range. For
example, the effect of an inductive load in parallel with the excitation capacitor will reduce
the resulting effective load impedance (Zeff) (Simoes & Farret, 2004).
Zeff = R + j
(26)
This change in the effective self-excitation increases the slope of the straight line of the
capacitive reactance (Figure 3), reducing the terminal voltage. This phenomenon is more
pronounced when the load becomes highly inductive.
Double Fed Induction Generator-Basic Principles (DFIG)

Wound rotor induction generators (WRIGs) are provided with three phase
windings on the rotor and on the stator. They may be supplied with energy at both rotor
and stator terminals. This is why they are called doubly fed induction generators (DFIGs)
or double output induction generators (DOIGs). Both motoring and generating operation
modes are feasible, provided the power electronics converter that supplies the rotor
circuits via slip-rings and brushes is capable of handling power in both directions. As a
generator, the WRIG provides constant (or controlled) voltage Vs and frequency f 1 power
through the stator, while the rotor is supplied through a static power converter at variable
voltage Vr and frequency f 2 . The rotor circuit may absorb or deliver electric power. As
the number of poles of both stator and rotor windings is the same, at steady state,
according to the frequency theorem, the speed
is as follows:
The sign is positive (+) in Equation 1.1 when the phase sequence in the rotor is the same
as in the
1,
that is, sub
Equation 1.1 corresponds to an inverse phase sequence i
super synchronous operation.
1,
that is,
2
has
to be modified in step with the speed variation. This way, variable speed at constant
frequency (and voltage) may be maintained by controlling the voltage, frequency, and
phase sequence in the rotor circuit. It may be argued that the WRIG works as a
synchronous generator (SG) with three-phase alternating current (AC) excitation at slip
2
m,
the stator induces voltages in the
rotor circuits even at steady state, which is not the case in conventional SGs. Additional
power components thus occur. The main operational modes of WRIG are depicted in
Figure 1.1a through Figure 1.1d (basic configuration shown in Figure 1.1a). The first two
modes (Figure 1.1b and Figure 1.1c) refer to the already defined sub synchronous and
super synchronous generations. For motoring, the reverse is true for the rotor circuit; also,
the stator absorbs active power for motoring. The slip S is defined as follows:
S
characteristics of an induction machine. The main output active power is delivered
through the stator, but in super synchronous operation, a good part, about slip stator
powers (SPs), is delivered through the rotor circuit. With limited speed variation range,
say from S max
S max , the rotor-side static converter rating for zero reactive power
capability on the rotor side would be PCONV
S max PS With S max typically equal to
0.2 to 0.25, the static power converter ratings and costs would correspond to 20 to 25%
of the stator delivered output power. At maximum speed, the WRIG will deliver
increased electric power, Pmax
with the WRIG designed at Ps for
speed. The increased power is delivered at
higher than rated speed:
Consequently, the WRIG is designed electrically for Ps

wm
max
1,
but mechanically at
and P max . The capability of a WRIG to deliver power at variable speed but at
constant voltage and frequency represents an asset in providing more flexibility in power
conversion and also better stability in frequency and voltage control in the power systems
to which such generators are connected. The reactive power delivery by WRIG depends
heavily on the capacity of the rotor-side converter to provide it. When the converter
works at unity power delivered on the source side, the reactive power in the machine has
to come from the rotor-side converter. However, such a capability is paid for by the
increased ratings of the rotor-side converter. As this means increased converter costs, in
general, the WRIG is adequate for working at unity power factor at full load on the stator
side. Large reactive power releases to the power system are still to be provided by
existing SGs or from WRIGs working at synchronism (S = 0,
= 0) with the back-to-
back pulse-width modulated (PWM) voltage converters connected to the rotor controlled
adequately for the scope. Wind and small hydro energy conversion in units of 1 megawatt
(MW) and more per unit require variable speed to tap the maximum of energy reserves
and to improve efficiency and stability limits. High-power units in pump-storage hydro(400 MW) and even thermo power plants with WRIGs provide for extra flexibility for the
ever-more stressed distributed power systems of the near future. Even existing (old) SGs
may be retrofitted into WRIGs by changing the rotor and its static power converter
control. The WRIGs may also be used to generate power solely on the rotor side for
rectifier loads (Figure 1.1d). To control the direct voltage (or direct current [DC]) in the
load, the stator voltage is controlled, at
1,
by a low-cost alternating
current (AC) three-phase voltage changer. As the speed increases, the stator voltage has
to be reduced to keep constant the current in the DC load
m ).
If the machine has a large number of poles (2p 1 = 6, 8, 12), the stator AC
excitation input power becomes rather low, as most of the output electric power comes
from the shaft (through motion). Such a configuration is adequate for brushless exciters
needed for synchronous motors (SMs) or for generators, where field current is needed
from zero speed, that is, when full-power converters are used in the stator of the
respective SMs or SGs. With 2p 1 = 8, n = 1500 rpm, and f 1 = 50 Hz, the frequency of the
rotor output f 2 = f 1 + np 1 = 50 + (1500/60)* 4 = 150 Hz. Such a frequency is practical
with standard iron core laminations and reduces the contents in harmonics of the output
rectified load current.
So, the reactive power required to magnetize the machine may be delivered by the
rotor or by the stator or by both. The presence of S in Equation 1.40 is justified by the
fact that machine magnetization is perceived in the stator at stator frequency
1.
As the
static power converter rating depends on its rated apparent power rather than active
power, it seems to be practical to magnetize the machine from the stator. In this case,
however, the WRIG absorbs reactive power through the stator from the power grids or
from a capacitive-resistive load. In stand-alone operation mode, however, the WRIG has
to provide for the reactive power required by the load up to the rated lagging power factor
conditions. If the stator operates at unity power factor, the rotor-side static power
converter has to deliver reactive power extracted either from inside itself (from the
capacitor in the DC link) or from the power grid that supplies it. As magnetization is
achieved with lowest kVAR in DC, when active power is not needed, the machine may
r
1)
to fully contribute to the voltage stability and
control in the power system. To further understand the active and reactive power flows in
the WRIG, phasor diagrams are used.
DYNAMIC MODEL OF PM SYNCHRONOUS MOTORS
ABSTRACT: In a permanent magnet synchronous motor where inductances vary as a function of rotor
angle, the 2 phase (d-q) equivalent circuit model is commonly used for simplicity and intuition. In this
article, a two phase model for a PM synchronous motor is derived and the properties of the circuits and
variables are discussed in relation to the physical 3 phase entities. Moreover, the paper suggests
methods of obtaining complete model parameters from simple laboratory tests. Due to the lack of
developed procedures in the past, obtaining model parameters were very difficult and uncertain, because
some model parameters are not directly measurable and vary depending on the operating conditions.
Formulation is mainly for interior permanent magnet synchronous motors but can also be applied to
surface permanent magnet motors.
I. INTRODUCTION
PM synchronous motors are now very popular in a wide variety of industrial applications. A large majority
of them are constructed with the permanent magnets mounted on the periphery of the rotor core. Following [1], we
will call them as the Surface Permanent Magnet (SPM) synchronous motors. When permanent magnets are buried
inside the rotor core rather than bonded on the rotor surface, the motor not only provides mechanical ruggedness but
also opens a possibility of increasing its torque capability. By designing a rotor magnetic circuit such that the
inductance varies as a function of rotor angle, the reluctance torque can be produced in addition to the mutual
reaction torque of synchronous motors. This class of Interior PM (IPM) synchronous motors can be considered as
the reluctance synchronous motor and the PM synchronous motor combined in one unit. It is now very popular in
industrial and military applications by providing high power density and high efficiency compared to other types of
motors.
Conventionally, a 2-phase equivalent circuit model (d-q model) [2] has been used to analyze reluctance
synchronous machines. The theory is now applied in analysis of other types of motors [3-7] including PM
synchronous motors, induction motors etc. In Section II, an equivalent 2-phase circuit model of a 3-phase IPM
machines is derived in order to clarify the concept of the transformation and the relation between 3-phase quantities
and their equivalent 2-phase quantities. Although the above equivalent circuit is very popular, discussions on
obtaining parameters of the equivalent circuit for a given motor are rarely found. The main objective of the article is
to establish a method to obtain 2-phase circuit parameters from physically measured data. Throughout the article,
the following assumptions are made:
(1) Stator windings produce sinusoidal mmf distribution. Space harmonics in the air-gaps are neglected.
(2) Air-gap reluctance has a constant component as well as a sinusoidally varying component.
(3) Balanced 3 phase supply voltage is considered.
(4) Although magnetic saturation is considered, eddy current and hysteresis effects are neglected.
In addition, presence of damper windings are not considered here because they are not used in PM synchronous
machines in general. A model with short-circuited damper windings may be used to analyze eddy current effects.
Nomenclature on this article is listed in the following. More definitions may appear as appropriate during
discussion. For notational convenience, units on all angles are in degrees.
P:
Ia, Ib, Ic:
Va, Vb, Vc:
Id, Iq:
number of poles of the motor.

phase a, b, c instantaneous stator current.
phase a, b, c instantaneous stator voltage.
d- and q- axis components of stator current
Vd, Vq:
Rs:
p:
Ld, Lq:
Ls:
Lx:
m:
:
:
d and q- axis components of stator phase voltage

stator resistance
d/dt
d- and q- axis stator self inductance
Average inductance. Ls = (1/2) (Lq + Ld)
Inductance fluctuation. Lx = (1/2) (Lq Ld)
peak flux linkage due to permanent magnet.
electrical angle between a-axis and q-axis in degrees. See Fig. 2.1.
= p , angular velocity of rotation (in electrical rad/Sec.)
II. DERIVATION OF A PM SYNCHRONOUS MOTOR MODEL
Fig. 2.1 illustrates a conceptual cross-sectional view of a 3-phase, 2-pole IPM synchronous motor along
with two reference frames. To illustrate the inductance difference (Lq > Ld), rotor is drawn with saliency although
actual rotor structure is more likely a cylinder. The stator reference axis for the a-phase is chosen to the direction of
maximum mmf when a positive a-phase current is supplied at its maximum level. Reference axis for b- and c- stator
frame are chosen 120 and 240 (electrical angle) ahead of the a-axis, respectively. Following the convention of
choosing the rotor reference frame, the direction of permanent magnet flux is chosen as the d-axis, while the q-axis is
90 degrees ahead of the d-axis. The angle of the rotor q-axis with respect to the stator a-axis is defined as . Note
that as the machine turns, the d-q reference frame is rotating at a speed of = d /dt, while the stator a-,b-,c- axes are
fixed in space. We will find out later that the choice of this rotating frame greatly simplifies the dynamic equations
of the model.
The electrical dynamic equation in terms of phase variables can be written as
Va = Rs Ia + p a
(2.1)
Vb = Rs Ib + p b
(2.2)
Vc = Rs Ic + p c
(2.3)
while the flux linkage equations are

a = Laa Ia + Lab Ib + Lac Ic +
ma
(2.4)
b = Lab Ia + Lbb Ib + Lbc Ic +
mb
(2.5)
c = Lac Ia + Lbc Ib + Lcc Ic +
mc,
(2.6)
considering symmetry of mutual inductances such as Lab=Lba. Note that in the above equations, induc-tances are
functions of the angle . Since stator self inductances are maximum when the rotor q-axis is aligned with the phase,
while mutual inductances are maximum when the rotor q-axis is in the midway between two phases. Also, note that
the effects of saliency appeared in stator self and mutual inductances are indicated by the term 2 .
Laa = Lso + Lsl + Lx cos (2 )
(2.7)
Lbb = Lso + Lsl + Lx cos (2 + 120)
(2.8)
Lcc = Lso + Lsl + Lx cos (2 - 120)
(2.9)
Lab = - (1/2)Lso + Lx cos (2 - 120)
(2.10)
Lbc = - (1/2)Lso + Lx cos (2 )
(2.11)
Lac = - (1/2)Lso + Lx cos (2 + 120)
(2.12)
For mutual inductances in the above equations, the coefficient -(1/2) comes due to the fact that stator phases are
displaced by 120 , and cos(120) = -(1/2). Meanwhile, flux-linkages at the stator windings due to the permanent
magnet are
ma =
m cos
(2.13)
mb =
m cos ( - 120)
(2.14)
mc =
m cos ( + 120)
(2.15)
For this model, input power Pi can be represented as

Pi = Va Ia + Vb Ib + Vc Ic
(2.16)
Unfortunately, the output power Po and the output torque T = (P/2) Po/ cannot simply be derived in this 3-phase
model. The torque can be expressed as
T = (P/6) (Lq - Ld) [ { (Ia2 - 0.5 Ib2 - 0.5 Ic2 -Ia Ib - Ia Ic + 2 Ib Ic) sin 2
+ ( 3/2) (Ib2 + Ic2 - 2Ia Ib + 2 Ia Ic) cos 2 } + m { (Ia - 0.5 Ib - 0.5 Ic) cos
+ ( 3/2) (Ib - Ic) sin }].
(2.17)
Refer to [6] for detailed derivation by using energy method.
b-axis
q-axis
a
b
c
S
a-axis
N
c
b
a
d-axis
c-axis
Fig. 2.1 PM Synchronous Motor
Now, let S represent any of the variables (current, voltage, and flux linkage) to be transformed from the a-bc frame to d-q frame. The transformation in matrix form is given by
Sq
Sd
So
= (2/3)
cos
sin
0.5
cos ( - 120)
sin ( - 120)
0.5
cos ( + 120)
sin ( + 120)
0.5
Sa
Sb
Sc
(2.18)
Here So component is called the zero sequence component, and under balanced 3-phase system this component is
always zero. Since it is a linear transformation, its inverse transformation exists and is
Sa
Sb
Sc
cos
cos ( - 120)
cos( + 120)
sin
sin ( - 120)
sin ( + 120)
1
1
1
Sq
Sd
So
(2.19)
Now, by applying the transform of Eq. 2.18 to voltages, flux-linkages and currents of Eqs.2.1-2.6, we get a set of
simple equations as
Vq = Rs Iq + p q +
(2.20)
Vd = Rs Id + p d -
q,
(2.21)
where
q = Lq Iq
d = Ld Id +
(2.22)
m.
(2.23)
Here, Lq and Ld are called d- and q-axis synchronous inductances, respectively, and are defined as
Lq = (3/2) ( Lso + Lx) + Lsl
(2.24)
Ld = (3/2) ( Lso - Lx) + Lsl.
(2.25)
As noticed in the above equation, synchronous inductances are effective inductances under balanced 3 phase
conditions. Each synchronous inductance is made up of self inductance (which includes leakage inductance) and
contributions from other 2 phase currents. Now, a more convenient equation may result by eliminating the fluxlinkage terms from Eqs.2.20-2.21 as
Vq = (Rs + Lq p) Iq +
Ld Id +
Vd = (Rs + Ld p) Id -
Lq Iq
(2.26)
(2.27)
Fig. 2.1 shows a dynamic equivalent circuit of an IPM synchronous machine based on Eqs.2.26-2.27. Note that in
practice, magnetic circuits are subject to saturation as current increases. Especially, when Iq is increased, the value
of Lq is decreased and m and Ld is subject to armature reaction. Since Id is maintained to zero or negative value
(demagnetizing) in most operating conditions, saturation of Ld rarely occurs.
Rs
Lq
Rs
+
Iq
Vq
-
Ld
Id
m
Ld Id
+
Vd
-
(a) q-axis circuit
Lq Iq
+
(b) d-axis circuit
Fig. 2.1 Equivalent Circuit of a PM Synchronous Motor

For this model, instantaneous power can be derived from Eq. 2.16 via transformation as
Pi = (3/2) { Vq Iq + Vd Id } ,
(2.28)
neglecting the zero sequence quantities. The output power can be obtained by replacing Vq and Vd by the
associated speed voltages as
Po = (3/2) { -
q Id +
d Iq}
(2.29)
The produced torque T, which is power divided by mechanical speed can be represented as
T = (3/2) (P/2) ( m Iq + (Ld - Lq) Iq Id ).
(2.30)
It is apparent from the above equation that the produced torque is composed of two distinct mechanisms. The first
term corresponds to "the mutual reaction torque" occurring between Iq and the permanent magnet, while the second
term corresponds to "the reluctance torque" due to the differences in d-axis and q-axis reluctance (or inductance).
Note that in order to produce additive reluctance torque, Id must be negative since Lq > Ld.
In order to discuss about the relation between the original 3-phase system and the 2-phase equivalent
system, consider the transformation of Eq. 2.18-2.19. In fact, this reversible linear transformation can be interpreted
as a combination of two transformations. First, let - axis be a stationary frame so that -axis and -axis coincide
with q- and d-axis, respectively when the angle is zero. The transformation from 3-axis variables to 2-axis
variables is
S
S
So
= (2/3)
1
0
0.5
cos (120 )
-sin (120 )
0.5
cos (120 )
sin (120 )
0.5
Sa
Sb
Sc .
(2.31)
As before, the variable S represents voltage, current or flux linkage and the zero sequence component So is always
zero for a balanced 3 phase system. The second transformation simply converts from stationary - frame to the
rotating d-q frame as
Sq
Sd
So
cos
sin
0
- sin
cos
0
0
0
1
S
S
So
(2.32)
It can be easily verified that multiplication of the above two transformations lead to Eq. 2.18. Since the d-q frame
itself is rotating at a synchronous frequency, all sinusoidally modulated terms vanish after the transformation into this
d-q frame. Notice that since the transformation of Eq. 2.18 (and Eq. 2.31) is not unitary (A square matrix is unitary
if its inverse is the same as its transpose), the power and torque of the 2-phase equivalent system is different from
those of the original 3-phase system. To calculate power and torque from the 2-phase equivalent circuit, (3/2) factor
has to be included as shown in Eq. 2.28-2.30. The reason that this non-unitary transformation of Eq. 2.18 is popular
is because the magnitude of voltages, currents and flux linkages are the same in both frames. See Appendix for
further information regarding a unitary transformation. In this 2-phase equivalent circuit, inductances are roughly
(3/2) times those of the actual 3 phase value (refer to Eq. 2.24-25). These "synchronous inductances" Ld and Lq are
the effective inductances seen by a phase winding during balanced operation. In addition to the self-flux linkage of
one phase, additional flux linkages are produced from the other two phase currents.
For some applications, it is useful to define voltage vector Vs and current vector Is whose magnitudes are
|Vs| = Vs =
|Is| = Is =
Vq2 + Vd2,
(2.33)
Iq2 + Id2.
(2.34)
Assume that current vector Is is m degrees ahead of the q-axis. Then, the relation between the stator current
magnitude Is, and Id and Iq are
Iq = Is cos m,
(2.35)
Id = - Is sin m,
(2.36)
and Eq. 2.30 can be expressed in terms of m as

T = (3/2)(P/2)( m Is cos m + 0.5 (Lq-Ld) Is2sin 2 m).
(2.37)
For surface PM motors whose Lq = Ld, the reluctance torque term of the above equation vanishes and the above
equation is reduced to
T = (3/2) (P/2) m Is cos m.
(2.38)
Here, the maximum torque is produced when m = 0 , or the angle between the stator flux linkage vector and the PM
flux linkage vector on the rotor is 90 degrees which is analogous to the characteristics of a separately excited DC
motor. For interior PM synchronous motors, the reluctance torque is not negligible and higher torque can be
produced by appropriately adjusting the angle m.

Peres 10PPS103 2 Electrical Machines PDF

Uploaded by

Copyright:

Available Formats

Peres 10PPS103 2 Electrical Machines PDF

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Peres 10PPS103 2 Electrical Machines PDF

Uploaded by

Copyright:

Available Formats

ELECTRICAL GENERATORS USED FOR WIND POWER GENERATION

The mechanical power of a wind turbine is converted into electric power by an

segments. It switches the positive output terminal continuously to the conductor

can be eliminated altogether by using a reluctance rotor, in which the synchronous

CONSTRUCTION OF INDUCTION GENERATOR

Where f = frequency of the stator excitation

induced voltage is given by Faradays law of electromagnetic induction, namely:

=the magnetic flux of the stator linking the rotor loop.

ROTOR SPEED AND SLIP

Thus, the squirrel cage induction machine is essentially a constant-speed machine,

SELF EXCITATION OF INDUCTION GENERATOR (SEIG)

Figure (4) Self-excitation on self-excited induction generator (SEIG):

excitation), at frequency at frequency

, produced by the remnant flux density in

the rotor left there from previous operation events.

for constant (regulated) prime-mover speed

Steady-State Analysis of Three-Phase SEIGs

Loop impedance models

Nodal admittance models

The Analysis and Modelling

3. Self-Excited Induction Generator (SEIG)

Fig. 2. Self-excited induction generator with external capacitor.

Fig. 3. Determination of stable operation of self-excited induction generator.

Fig. 4. Equivalent circuit of self-excited induction generator with R-L Load.

Where Z is the net loop impedance given by

Since at steady-state excitation I 0, it follows from (equation 1) that Z = 0 , which implies

is the dummy variable of integration

Fig. 5. Transformation for stationary circuits portrayed bytrigonometric relationships.

Fig. 6. Two-pole, 3-phase, wye connected symmetrical induction machine.

"" denotes rotor values referred to the stator side.

Llsiqs + Lm (iqs + i'qr)

Llsids + Lm (ids + i'dr)

qr = Llriqr + Lm (iqs + i'qr)

dr = Llridr + Lm (ids + i'dr)

Fig. 7. Arbitrary reference-frame equivalent circuits for a 3-phase, symmetrical induction

The torque and speed are related by the following expressions:

Substituting (equation 12) in (equation 21), will result

0 = Vcq + rsiqs + Lspiqs + Lmpiqr

Double Fed Induction Generator-Basic Principles (DFIG)

that is, sub

Equation 1.1 corresponds to an inverse phase sequence i

super synchronous operation.

the stator induces voltages in the

capability on the rotor side would be PCONV

S max PS With S max typically equal to

with the WRIG designed at Ps for

speed. The increased power is delivered at

higher than rated speed:

Consequently, the WRIG is designed electrically for Ps

= 0) with the back-to-

to fully contribute to the voltage stability and

DYNAMIC MODEL OF PM SYNCHRONOUS MOTORS

number of poles of the motor.

d and q- axis components of stator phase voltage

while the flux linkage equations are

b = Lab Ia + Lbb Ib + Lbc Ic +

c = Lac Ia + Lbc Ib + Lcc Ic +

Lbb = Lso + Lsl + Lx cos (2 + 120)

Lcc = Lso + Lsl + Lx cos (2 - 120)