Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings

Designation: A780/A780M 09
Standard Practice for
Repair of Damaged and Uncoated Areas of Hot-Dip

Galvanized Coatings1
This standard is issued under the fixed designation A780/A780M; the number immediately following the designation indicates the year
of original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.
A superscript epsilon () indicates an editorial change since the last revision or reapproval.
This standard has been approved for use by agencies of the Department of Defense.
2. Referenced Documents
1. Scope*
2.1 ASTM Standards:2

A902 Terminology Relating to Metallic Coated Steel Products
D520 Specification for Zinc Dust Pigment
2.2 Society for Protective Coatings (SSPC) Documents:3
SSPC-PA2 Measurement of Dry Paint Thickness with Magnetic Gages
SSPC-SP2 Hand Tool Cleaning
SSPC-SP5/NACE No.1 White Metal Blast Cleaning
SSPC-SP10/NACE No.2 Near-White Blast Cleaning
SSPC-SP11 Power Tool Cleaning to Bare Metal
1.1 This practice describes methods that may be used to

repair damaged hot-dip galvanized coatings on hardware,
structural shapes, and other products fabricated prior to hot-dip
galvanizing, and uncoated areas remaining after initial hot-dip
galvanizing. The damage may be the result of welding or
cutting (flame), in which case the coating will be damaged
predominantly by burning. This practice can also be used to
repair hot-dip galvanized coatings damaged by excessively
rough handling during shipping or erection. Requirements
concerning the renovation of uncoated areas remaining after
initial hot-dip galvanizing are contained within the applicable
material specification.
3. Terminology
1.2 This practice describes the use of low melting point zinc
alloy repair rods or powders made specifically for this purpose,
the use of paints containing zinc dust, and the use of sprayed
zinc (metallizing).
3.1 DefinitionsFor definitions of terms used in this practice, refer to Terminology A902.
4. Materials
1.3 The extent of repair shall be limited to an area mutually

agreeable to the contracting parties. Similarly, contracting
parties shall agree to the repair method to be used.
4.1 PropertiesThe material used for repairs shall have the

following characteristics:
4.1.1 One application of the material shall provide a coating
thickness of at least 2.0 mils (50.8 m).
4.1.2 The applied coating shall provide barrier protection
and shall preferably be anodic to steel.
4.1.3 Application of the coating material shall be possible
under shop or field conditions.
1.4 This specification is applicable to orders in either

inch-pound units (as A780) or in SI units (as A780M).
Inch-pound units and SI units are not necessarily exact
equivalents. Within the text of this specification and where
appropriate, SI units are shown in brackets. Each system shall
be used independently of the other without combining values in
any way.
4.2 TypesThere are three types of material that possess the

required properties and may be used to repair damaged
galvanized coatings, as follows:
4.2.1 Zinc-Based SoldersZinc alloy solders are to be used
for repairs. The most common types of solders are zinccadmium, zinc-tin-lead, and zinc-tin-copper alloys. Zinccadmium and zinc-tin-lead alloys have liquidus temperatures in
the ranges from 518 to 527F (270 to 275C) and 446 to 500F
1.5 This standard does not purport to address the safety

problems, if any, associated with its use. It is the responsibility
of the user of this standard to establish appropriate safety and
health practices and determine the applicability of regulatory
limitations prior to use.
1
This practice is under the jurisdiction of ASTM Committee A05 on MetallicCoated Iron and Steel Products and is the direct responsibility of Subcommittee
A05.13 on Structural Shapes and Hardware Specifications.
Current edition approved May 1, 2009. Published May 2009. Originally
approved in 1980. Last previous edition approved in 2006 as A780 01(2006).
DOI: 10.1520/A0780_A0780M-09.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
contact ASTM Customer Service at [email protected]. For Annual Book of ASTM
Standards volume information, refer to the standards Document Summary page on
the ASTM website.
3
Available from Society for Protective Coatings (SSPC), 40 24th St., 6th Floor,
Pittsburgh, PA 15222-4656, http://www.sspc.org.
*A Summary of Changes section appears at the end of this standard

Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
Copyright by ASTM Int'l (all rights reserved); Mon Sep 17 01:09:42 EDT 2012
Downloaded/printed by
A780/A780M 09
(230 to 260C), respectively. (The liquidus temperature is that
temperature above which an alloy is completely molten.) The
zinc-tin-copper alloys have a liquidus temperature in the range
from 660 to 670F (349 to 354C), but they are applied while
in a semisolid state in the preferred application temperature
range from 480 to 570F (250 to 300C). The solders can be
used in rod form or as powders. Annex A1 describes the use of
zinc-based solders.
4.2.2 Paints Containing Zinc DustThese are usually based
on organic binders, pre-mixed and formulated specifically for
use on steel surfaces. Paints containing zinc dust, with concentrations of zinc dust in the range of 65 to 69 % or above 92 %
in the dried film, are considered equally effective for the repair
of damaged galvanized coatings. The repair paint to be used
shall be selected by the galvanizer, unless the purchaser
specifies a particular concentration or paint system. Corrosion
resistance and service performance are very dependent on the

properties of the paint system, the extent of surface preparation, and skills of individual applicators. Annex A2 describes
the use of paints containing zinc dust. Specification D520
describes the zinc dust component of these paints.
4.2.3 Sprayed ZincThis method involves the application
of a zinc coating by spraying the surface to be repaired with
droplets of molten metal using wire or ribbon, or powder
processes. Annex A3 describes the use of sprayed zinc.
4.3 For further information, reference may be made to the
papers, procedures, and specifications in Refs. (1) through (4)
(see list of references at the end of this practice).
5. Keywords
5.1 coatingszinc; galvanized coating repair; galvanized
coatings; touch-up; zinc coating repair; zinc coatings
ANNEXES
(Mandatory Information)
A1. REPAIR USING ZINC-BASED ALLOYS
A1.1 Clean the surface to be reconditioned using a wire

brush, a light grinding action, or mild blasting. To ensure that
a smooth reconditioned coating can be effected, surface preparation shall extend into the surrounding, undamaged galvanized coating.
A1.4 Rub the cleaned, preheated area with the repair stick to
deposit an evenly distributed layer of the zinc alloy. When
powdered zinc alloys are used, sprinkle the powder on the
cleaned, preheated surface and spread out with a spatula or
similar tool. The thickness of the applied coating shall be as
agreed upon between the contracting parties.
A1.2 If the area to be reconditioned includes welds, first

remove all weld flux residue and weld spatter (of a size that
cannot be removed by wire brushing or blast cleaning) by
mechanical means, such as chipping, grinding, or power
scaling, etc.
A1.5 When the repair has been effected, remove flux residue
by rinsing with water or wiping with a damp cloth.
A1.6 Take thickness measurements with either a magnetic,
electromagnetic, or eddy-current gage to ensure that the
applied coating is as specified.
A1.3 Preheat the cleaned area to be reconditioned to at least

600F (315C). Do not overheat the surface beyond 750F
(400C), nor allow the surrounding galvanized coating to be
burned. Wire brush the surface to be reconditioned during
preheating. Pre-flux, if necessary.
A2. REPAIR USING PAINTS CONTAINING ZINC DUST
A2.1 Preparation of the damaged surface will be influenced

by the type of paint selected and the anticipated service
conditions. Experience shows that in general, organic zinc-rich
systems are tolerant of marginal surface preparation. Most
organic paints containing zinc dust are not critical of climatic
or atmospheric conditions for curing. The following general
guidelines shall apply:
A2.1.1 Surfaces to be reconditioned with paints containing

zinc dust shall be clean, dry, and free of oil, grease, preexisting
paint, and corrosion by-products.
A2.1.2 Where anticipated, field service conditions include
immersion, blast clean the surface in accordance with SSPCSP10/NACE No. 2 near white metal. For less critical field
A780/A780M 09
exposure conditions, clean the surface to bare metal, in
accordance with SSPC-SP11, as a minimum. Where circumstances do not allow blast or power tool cleaning, it is
permissible to hand tool areas clean in accordance with
SSPC-SP2. To ensure that a smooth reconditioned coating can
be effected, surface preparation shall extend into the undamaged galvanized coating. The method and extent of surface
preparation shall be mutually agreeable to the contracting
parties.
A2.1.4 Spray or brush-apply the paints containing zinc dust

to the prepared area. Apply the paint as in accordance with the
manufacturers printed instructions in a single application
employing multiple passes to achieve a dry film thickness to be
agreed upon between the contracting parties. Allow adequate
curing time before subjecting repaired items to service conditions in accordance with the manufacturers printed instructions.
A2.1.5 Take thickness measurements with either a magnetic, electromagnetic, or eddy-current gage to ensure that the
applied coating is as specified in accordance with SSPC-PA2.
A2.1.3 If the area to be reconditioned includes welds, first

remove all weld flux residue and weld spatter (of a size that
cannot be removed by wire brushing or blast cleaning) by
mechanical means, such as chipping, grinding, or power
scaling, etc.
A3. REPAIR USING SPRAYED ZINC (METALLIZING)
A3.6 The surface of the sprayed coating shall be of uniform

texture, free of lumps, coarse areas, and loosely adherent
particles.
A3.1 Surfaces to be reconditioned by zinc metallizing shall

be clean, dry and free of oil, grease, and corrosion products.
A3.2 If the area to be reconditioned includes welds, first
remove all flux residue and weld spatter of a size or type that
cannot be removed by blast cleaning by mechanical means,
that is, chipping, etc.
A3.7 The nominal thickness of the sprayed zinc coating

shall be previously agreed upon between the contracting
parties.
A3.3 Blast clean the surface to be reconditioned in accordance with SSPC-SP5/NACE No. 1, white metal.
A3.8 Take thickness measurements with either a magnetic,

electromagnetic, or eddy-current gage to ensure that the
applied coating is as specified.
A3.4 To ensure that a smooth reconditioned coating can be

effected, surface preparation shall be extended into the surrounding undamaged galvanized coating.
A3.5 Apply the coating to the clean and dry surface by
means of metal-spraying pistols fed with either zinc wire or
zinc powder. Apply the sprayed coating as soon as possible
after surface preparation and before visible deterioration of the
surface has occurred.
REFERENCES
(1) Van Eijnsbergen, J. F. H., et al, Reconditioning Damaged Galvanized

Surfaces, 6th International Conference on Hot Dip Galvanizing,
Interlaken, June 1961, pp. 128141.
(2) SSPC-Paint-20, Zinc Rich Coatings, Type I Inorganic, Type II
Organic, Steel Structures Painting Council, 4400 Fifth Ave., Pittsburgh, PA 15213, 1979.
(3) MIL-P-21035 (Ships), Military Specification, Paint, High Zinc Dust

Content, Galvanizing Repair, Amendment 1, U.S. Government
Printing Office, Washington, DC, 1970.
(4) Recommended Practices for Fused Thermal Sprayed Deposits,
American Welding Society, Inc., 550 N.W. LeJeune Rd., Miami, FL
33135, 1975.
A780/A780M 09
SUMMARY OF CHANGES
Committee A05 has identified the location of selected changes to this standard since the last issue
(A780 01(2006)) that may impact the use of this standard. (May 1, 2009)
(1) Revised 1.4 and changed designation to make standard
applicable in both units.
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or [email protected] (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).

Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings

Uploaded by

Copyright:

Available Formats

Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized Coatings

Uploaded by

Copyright:

Available Formats

Designation: A780/A780M 09

Standard Practice for

Repair of Damaged and Uncoated Areas of Hot-Dip

2.1 ASTM Standards:2

1.1 This practice describes methods that may be used to

1.3 The extent of repair shall be limited to an area mutually

4.1 PropertiesThe material used for repairs shall have the

1.4 This specification is applicable to orders in either

4.2 TypesThere are three types of material that possess the

1.5 This standard does not purport to address the safety

*A Summary of Changes section appears at the end of this standard

resistance and service performance are very dependent on the

A1.1 Clean the surface to be reconditioned using a wire

A1.2 If the area to be reconditioned includes welds, first

A1.3 Preheat the cleaned area to be reconditioned to at least

A2. REPAIR USING PAINTS CONTAINING ZINC DUST

A2.1 Preparation of the damaged surface will be influenced

A2.1.1 Surfaces to be reconditioned with paints containing

A2.1.4 Spray or brush-apply the paints containing zinc dust

A2.1.3 If the area to be reconditioned includes welds, first

A3. REPAIR USING SPRAYED ZINC (METALLIZING)

A3.6 The surface of the sprayed coating shall be of uniform

A3.1 Surfaces to be reconditioned by zinc metallizing shall

A3.7 The nominal thickness of the sprayed zinc coating

A3.8 Take thickness measurements with either a magnetic,

A3.4 To ensure that a smooth reconditioned coating can be

(1) Van Eijnsbergen, J. F. H., et al, Reconditioning Damaged Galvanized

(3) MIL-P-21035 (Ships), Military Specification, Paint, High Zinc Dust

You might also like