Scribd
Upload
39 views

Lecture 2: Fundamentals and PCB Layout: 2.996/6.971 Biomedical Devices Design Laboratory

This document provides an overview of fundamental circuit elements like resistors, capacitors, and inductors. It discusses circuit analysis techniques including Ohm's law, KVL, KCL and impedance. Simple filters and cascaded filters are introduced. Practical component considerations for resistors, capacitors, inductors, and PCB layout are covered. Key topics include component types, parameters, applications, layout techniques to minimize interference, and general design guidelines.

Uploaded by

eran1900
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
39 views

Lecture 2: Fundamentals and PCB Layout: 2.996/6.971 Biomedical Devices Design Laboratory

This document provides an overview of fundamental circuit elements like resistors, capacitors, and inductors. It discusses circuit analysis techniques including Ohm's law, KVL, KCL and impedance. Simple filters and cascaded filters are introduced. Practical component considerations for resistors, capacitors, inductors, and PCB layout are covered. Key topics include component types, parameters, applications, layout techniques to minimize interference, and general design guidelines.

Uploaded by

eran1900
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 28

2.996/6.

971 Biomedical Devices Design


Laboratory

Lecture 2: Fundamentals
and PCB Layout
Instructor: Hong Ma
Sept. 12, 2007

Fundamental Elements
Resistor (R)
Capacitor (C)
Inductor (L)
Voltage Source
Current Source
Enough to model any physical linear circuit

Fundamental Relationships
Ohms law: R = V / I
KVL, KCL Conservation laws
Impedance:
1
ZC =
Z L = j L
jC
Treat capacitors and inductors as resistors

Fundamental question:
Given an arbitrary circuit, what happens when you
hook up another circuit up to it?

Thevenin-Norton Equivalents

Represent an arbitrary circuit using a source and a


source impedance
Thevenin and Norton representation is equivalent
Result: Reduce all circuits into one fundamental circuit

Source and Load


Sources
Power supply
Signal Generator
Sensor
Amplifier output

Optimize for Voltage: ZLOAD >> ZSOURCE


Optimize for Current: ZLOAD << ZSOURCE
Optimize for Power: ZLOAD = ZSOURCE
Purpose of amplifier / active circuit:
impedance transform

Loads
Actuator
Measurement
device
Amplifier input

Simple Filters

RC Low pass
RC high pass
Bandpass
Bandstop (notch)

Simple Cascaded Filters


What if 2 stages are needed?

Practical Introduction to Passive


Components

Resistors
Range: 1 to 22M
Carbon composite (axial)
5% accuracy typical

Wirewound

Images removed due to copyright restrictions.


Photo examples of resistors.

1% accuracy typical

Thick film (Screen printed / electroplated)


Accuracies down to 1%

Thin film (Vacuum deposited)


Accuracies down to 0.1%

Temperature coefficient: 20-200 ppm / C

Potentiometer

Concerns:
Over-usage
Wiper skips not all values are achievable
Mechanical stability multi-turn not
necessarily better

Courtesy of PagerMotors.com. Used with permission.

Practical Capacitor Considerations


Accuracy: 10%
typical
Effective series
capacitance
Dielectric soakage
(dielectric absorption)
Temperature
dependence

ESR

Ceramic Capacitors
Most common type
1pF to 1F
Accuracy
Through-Hole 20%
SMT 10%

Images removed due to copyright restrictions.


Photo examples of ceramic capacitors.

Low ESR, loss tangent 0.002


Temperature coefficient
Z5U, X7R, C0G (NP0)

Cost = ~$0.01 in quantity

Aluminum Electrolytic Capacitors


Primary use: power supply bypassing
Range: 1F 1F Typical: 100F
Cost: ~$0.10 depending on size
Polar, designated by the negative terminal
Will blow up if reverse biased
Nonpolar versions available
Images removed due to copyright restrictions.
Photo examples of aluminum electrolytic capacitors.

Very inaccurate
Typical tolerance: +80%, -20%
Limited lifetime
High ESR, loss tangent = R/Xc 0.2

Tantalum Electrolytics
Similar to aluminum electrolytics, but better
energy density
More expensive than aluminum electrolytics
Range: 0.1F to 1000F
Polarity designated by the positive terminal

Images removed due to copyright restrictions.


Photo examples of tantalum electrolytics.

Double Layer Capacitors

Extremely high capacitance


Range 0.1F 1000F
Low voltage rating
Used for energy storage

Images removed due to copyright restrictions.


Photo examples of double layer capacitors.

Specialty Capacitors: Polypropylene


Improved performance:
Accuracy
ESR at high frequencies
Low dielectric soakage
Temperature stability
Higher breakdown voltage

Tradeoffs
Larger size
Smaller range of values
Higher cost: ~$0.10

Image removed due to copyright restrictions.


Photo of polypropylene capacitor.

Power Supply Bypassing


Ideal sources do not exist!
Source impedance increases with
frequency
Ceramic capacitor on each IC component
Electrolytic on both sides of the power
supply

Practical Inductors
Inaccurate (at best 10%)
Expensive
Parasitics
All inductors self resonate

Avoid whenever possible

Images removed due to copyright restrictions.


Photo examples of practical inductors.

Where to find information / parts


Manufacturers website: datasheet &
samples
Distributors:
Digikey
Mouser
Newark

Meta search engine: www.findchips.com

PCB Layers
Image removed due to copyright restrictions.

Substrate
FR-4 standard; Specialty: G-10, polyimide (Kapton), ceramic
Standard thicknesses: 0.062, 0.031

Copper

2, 4, up to 12 layers
Minimum trace/spacing 6 mil, smaller is possible
Thickness: 1 oz copper = 500 per square
Exposed copper tined with solder
Interlayer connection by vias; Blind and buried vias = $$$

Soldermask very important Hydrophobic to solder


Silkscreen

PCB Layout Error Sources


Capacitive interference
Inductive interference
Electromagnetic interference
Need a ground plane but why?!?

Image removed due to copyright restrictions.

Capacitive Interference
Cause: capacitance between nearby traces
When to watch out for it:
High impedance circuit nodes
High-voltage excitation signals
High frequency signals

How to avoid it:

Lower the circuit impedance


Use groundplanes and shielding to isolate signal lines
Boot-strap to reduce capacitance to ground
Separate analog and digital ground planes

Inductive Interference
Cause: mutual inductance between traces
When to watch out for it:
Large AC current
Transient switching
Long traces
Loops

How to Avoid Inductive Interference

Keep traces short


Make traces perpendicular
Use star power / ground routing
Reduce loop area
Careful use of ground planes
Watch out for return lines

Image removed due to copyright restrictions.


See Figure 12 here: http://www.analog.com/library/analogdialogue/archives/41-06/ground_bounce.html

Electromagnetic Interference (EMI)


Cause:
long traces/wires acting as an antenna

When to watch out for it:


Length > 1/20 wavelength

Source of interference

Wireless communication (900MHz, 2.4GHz, 5GHz)


FM radio
Microwave oven
Lightning, solar flares, cosmic rays
High speed processors

Real products must pass FCC and CE testing

Ferrite Bead
A lossy inductor
Resistor at high frequencies

Example photos removed due to copyright restrictions.

Where to put the ground planes?


Ground planes outside, signals inside:
Essentially eliminate capacitive interference

Ground planes inside, signal outside:


Ground plane with frewer interruptions

Image removed due to copyright restrictions.

Project Teams

You might also like