63988

Download as pdf or txt
Download as pdf or txt
You are on page 1of 23

UNIT V GAS MIXTURES AND PSYCHROMETRY

PART A
1. Define Mole Fraction.
Mole fraction of a gas in a gas mixture is defined as the ratio between the number of kmol of that gas and
the total number of kmol of the gas mixture.
2. Define Mass Fraction.
Mass fraction of a gas in a gas mixture is defined as the ratio between the mass of that gas and the total
mass of the gas mixture.
3. What is Partial Pressure?
The partial pressure of each constituent is that pressure which the gas would exert if it occupied alone that
volume occupied by the mixtures at the same temperature
4. What is Partial Volume?
The partial volume of a constituent gas in a gas mixture is the volume of that gas required to exert the
same pressure of the gas mixture, at the same temperature of the mixture.
5. Explain Daltons law of partial pressure.
The pressure of a mixture of gases is equal to the sum of the partial pressures of the constituents. The
partial pressure of each constituent is that pressure which the gas would expect if it occupied alone that
volume occupied by the mixtures at the same temperatures.
m
=
mA+mB+mC+.
= mA, mB - mass of the constituent.
p
=
pA+pB+pC+.
= pA, pB - partial pressure of the constituent.
6. Explain Amagats law of partial volume.
[APR/MAY 2015]
Amagats law states that the total volume of a gas mixture is equal to the sum of the partial volumes of all
constituent gases.
7. State Avogadros Law.
The number of moles of any gas is proportional to the volume of gas at a given pressure and temperature.
8. Define Molecular mass.
[NOV/DEC 2014]
Molecular mass is defined as the ratio between total mass of the mixture to the total number of moles
available in the mixture.
9. Define psychrometry.
The science which deals with the study of behavior of moist air (mixture of dry air and water vapour) is
known as psychrometry.
10. Define specific humidity.
It is defined as the ratio of the mass of water vapour (ms) in a given volume to the mass of dry air in a
given volume (ma).
11.Define absolute humidity.
It is the mass of water vapour present in a unit volume of dry air and is generally expressed in terms of
gram per cubic meter of dry air.
12. Define relative humidity.
It is defined as the ratio of partial pressure of water vapour (pw) in a mixture to the saturation pressure (ps)
of pure water at the same temperature of mixture.
13. Differentiate absolute humidity and relative humidity.
Absolute humidity is the mass of water vapour present in one kg of dry air. Relative humidity is the ratio
of the actual mass of water vapour present in one kg of dry air at the given temperature to the maximum
mass of water vapour it can with hold at the same temperature. Absolute humidity is expressed in terms of
kg/kg of dry air. Relative humidity is expressed in terms of percentage
14. Define Degree of saturation.
[NOV/DEC 2015]
It is the ratio of actual mass of water vapour in certain mass of dry air to the mass of water vapour in the
same mass of dry air when it is saturated at the same temperature.
15. What is meant by wet bulb temperature (WBT)?
It is the temperature recorded by a thermometer whose bulb is covered with cotton wick (wet) saturated
with water. The wet bulb temperature may be the measure of enthalpy of air. WBT is the lowest
temperature recorded by moistened bulb.
16. What is meant by dry bulb temperature (DBT)?
The temperature recorded by the thermometer with a dry bulb. The dry bulb thermometer cannot affect
by the moisture present in the air. It is the measure of sensible heat of the air.
17. What is psychrometer?
Psychrometer is an instrument which measures both dry bulb temperature and wet bulb temperature.
18. What is dew point temperature?
St. Josephs College of Engineering / St. Josephs Institute of Technology

31

The temperature at which the vapour starts condensing is called dew point temperature. It is also equal to
the saturation temperature at the partial pressure of water vapour in the mixture. The dew point
temperature is an indication of specific humidity.
19. Define dew point depression.
It is the difference between dry bulb temperature and dew point temperature of air vapour mixture. It is
also inversely proportional to the relative humidity of the air.
20. What is psychrometric chart?
It is the graphical plot with specific humidity and partial pressure of water vapour in y axis and dry bulb
temperature along x axis. The specific volume of mixture, wet bulb temperature, relative humidity and
enthalpy are the properties appeared in the psychrometric chart.
21. What is humidification and dehumidification?
The addition of water vapour into air is humidification and the removal of water vapour from air is
dehumidification.
22. What is effective temperature?
The effective temperature is a measure of feeling warmth or cold to the human body in response to the air
temperature, moisture content and air motion. If the air at different DBT and RH condition carries the
same amount of heat as the heat carried by the air at temperature T and 100% RH, then the temperature T
is known as effective temperature.
23. What are the important psychrometric processes?
1. Sensible heating and sensible cooling,
2. Cooling and dehumidification,
3. Heating and humidification,
4. Mixing of air streams,
5. Adiabatic evaporative cooling.
24. What is meant by adiabatic mixing?
The process of mixing two or more stream of air without any heat transfer to the surrounding is known as
adiabatic mixing. It takes place in air conditioning system.
25. Sketch the sensible heating process on a skeleton psychrometric chart.

26. When are the dry-bulb and dew-point temperatures identical?


The dry-bulb and dew-point temperatures are identical when the air is saturated.

27. What is evaporative cooling? Will it work in humid climates?


It is defined as the reduction in temperature resulting from the evaporation of a liquid, which removes
latent heat from the surface from which evaporation takes place and it will not work in humid climates.
29. State Gibbs-Daltons law.
[NOV/DEC 2015]
This states that as the pressure of a real gas approaches zero, the pressure of each component in the
mixture approaches its Partial Pressure. The Joule-Thomson Coefficient is a notable example of this. It
remains nonzero at P = 0, whereas the perfect gas value is identically zero.
30. Define sensible heat and latent heat.
[APR/MAY 2015]
Sensible heat is the heat that changes the temperature of the substance when added to it or when
abstracted from it. Latent heat is the heat that does not affect the temperature but change of state occurred
by adding the heat or by abstracting the heat.
31. Define sensible heat factor.
[NOV/DEC 2014]
St. Josephs College of Engineering / St. Josephs Institute of Technology

31

Sensible Heat Factor (SHF) is the ratio of total sensible heating load to that of the total heating load of the
air conditioning apparatus. SHF is used in the design process of the air conditioning apparatus
32. Define adiabatic saturation temperature.
[APR/MAY 2014]
It is the temperature at which the outlet air can be brought into saturation state by passing through the
water in the long insulated duct (adiabatic) by the evaporation of water due to latent heat of vapourisation. 33.
What is by-pass factor?
[APR/MAY 2014]
The bypass factor of the coil is defined as the ratio of temperature difference between the coil and the exit
air to the maximum possible theoretical temperature rise in air.
34. Why do wet clothes dry in the sun faster?
[NOV/DEC 2013]
The heat of sun causes evaporation of water from the wet clothes more rapidly than the evaporation in
shade. Due to this, wet clothes dry up quickly in sun than in shade.
35. When is humidification of air necessary?
[APR/MAY 2013]
Humidification of air is the process of adding moisture to the air and it is necessary to provide human
comfort.
36. How does the wet bulb temperature differ from the dry bulb temperature?
[APR/MAY 2013]
The thermometer on the psychrometer that contains the wet wick is called the "wet bulb". The
thermometer on the psychrometer without the wick is called the "dry bulb". The thermometers are then
whirled around the dowel by their strings. The thermometers are whirled until the wet bulb is dry. When
there is little water vapor present, the water on the wet bulb is able to evaporate. This results in a greater
difference between the wet and dry bulbs of the psychrometer. When the air is saturated with water vapor,
then the water on the wet bulb cannot evaporate.
37. In a gas mixture, which component will have the higher partial pressure - the one with the higher
mole number or the one with the larger molar mass?
[NOV/DEC 2009]
The one with the larger molar mass will have higher partial pressure.
38. What is the difference between dry air and atmospheric air?
[NOV/DEC 2009]
The difference between dry air and atmospheric air is that atmospheric air contains water vapor but dry
air contains no water vapor. Moisture content is zero in dry air.
39. Deduce the expression for the molecular weight of the mixture of two non-reacting ideal gases.
[APR/MAY 2007]

PART B
1. A vessel of 0.35 m3 capacity contains 0.4 kg of carbon monoxide (molecular weight=28) and 1 kg of air
at 20C. Calculate:
a) The partial pressure of each constituent,
b) The total pressure in the vessel.
The gravimetric analysis of air is to be taken as 23.3% oxygen (molecular weight = 32) and 76.7%
nitrogen (molecular weight = 28).
Hint:
Gravimetric analysis specifies mass of each component.
Find molar mass, mass fraction and finally calculate partial pressure and total pressure.
2. A vessel contains a mixture of 1 mole of CO2 and 4 moles of air at 1 bar and 20C. Calculate for the
mixture:
a) The masses of CO2, O2 and N2, and the total mass;
b) The percentage carbon content by mass;
c) The apparent molecular weight and the gas constant for the mixture;
d) The specific volume of the mixture.
The volumetric analysis of air can be taken as 21% oxygen and 79% nitrogen.
Hint:
Volumetric analysis specifies the volume of each component.
Find mass, molar mass, mass fraction, molecular weight and finally calculate specific volume of the
mixture.
3. A vessel of 1.8 m3 capacity contains oxygen at 8 bar and 50C. The vessel is connected to another vessel
of 3.6 m3 capacity containing carbon monoxide at 1 bar and 20C. A connecting valve is opened and the
gases mix adiabatically. Calculate :
a) The final temperature and pressure of the mixture;
St. Josephs College of Engineering / St. Josephs Institute of Technology
31

b)

The change of entropy of the system. Take: For oxygen, Cv = 21.07 kJ/mole K. For carbon
monoxide, Cv = 20.86 kJ/mole K.
Hint:
Number of moles has to be determined using characteristic gas equation.
System under consideration is adiabatic. Hence W = 0 and Q = 0.
Change in internal energy = [mCv(Tf - Ti)]Nitrogen + [mCv(Tf - Ti)]Oxygen = 0 (for finding final temperature of
the mixture)
For final pressure of the mixture, use PV = NRuT
Change in entropy of the system, associated with mixing process is the sum of changes in entropy of each
constituent.
4. A mixture of ideal gas consists of 3 kg of N2 and 5 kg of CO2 at a pressure of 300 kPa and at 20C. Find
a. The mole fraction of each constituent,
b. Equivalent molecular weight of the mixture,
c. Equivalent gas constant of the mixture,
d. The partial pressures and partial volumes,
e. Volume and density of the mixture and Cp and Cv of the mixture.
Assume, the value of CP/Cv for CO2=1.286, for N2=1.4.

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

5. Five moles of gas mixture contains 45% N2, 27% He and 28% C6H6 by mass. Considering analysis by
volume find (i) the number of moles of each constituent (ii) the volume of mixture at 3.5 bar and 20 C.
Hint:
Find mass of each component, mass fraction, molar mass, and the number of moles of each component.
Calculate volume of the mixture using characteristic gas equation.
6. 40 m3 of air per minute at 35C DBT and 50% R.H. is cooled to 25C DBT maintaining its specific
humidity constant. Determine: (i) Relative humidity (R.H.) of cooled air; (ii) Heat removed from air.
Hint:
Plot the initial and final condition of air in psychrometric chart to get RH of cooled air.
Or determine saturation pressure of water vapour to get relative humidity of heated air since RH = p v/pvs
Calculate enthalpy using the formula h = Cptdb + hvapour, where hvapour = [hg + 1.88 (tdb tdp)]
Heat removed from air can be calculated from mair(h1-h2).
7. 120 m3 of air per minute at 35C DBT and 50% relative humidity is cooled to 20C DBT by passing
through a cooling coil. Determine the following:
a) Relative humidity of out coming air and its wet bulb temperature.
b) Capacity of cooling coil in tonnes of refrigeration.
c) Amount of water vapour removed per hour.
Hint:
Locate the process in psychrometric chart and find RH and wet bulb temperature.
Calculate mass flow rate.
Capacity of cooling coil is the difference of enthalpy and 1 TR = 3.5 kW.
Amount of water vapour removed is the difference of specific humidity.
St. Josephs College of Engineering / St. Josephs Institute of Technology

31

8. It is required to design an air-conditioning plant for a small office room.


.
Outdoor conditions
14C DBT and 10C WBT
Required conditions
20C DBT and 60% R.H.
Amount of air circulation
0.30 m3/min./person
Seating capacity of office
60
The required condition is achieved first by heating and then by adiabatic humidifying.
Determine the following: (a) Heating capacity of the coil in kW and surface temperature required if the
bypass factor of coil is 0.4. (b) The capacity of the humidifier. Solve the problem by using
psychrometric chart.
Hint:
Locate the points 1 and 3 on the psychrometric chart.
Draw a constant enthalpy line through 3 and constant specific humidity line through 1. Locate the point
2 where the above two lines intersect.

From the psychrometric chart :

h1
h2 = h3
tdb2
vs1
The mass of air circulated per minute
(i) Heating capacity of the heating coil
(ii) Coil surface temperature
(iii) Capacity of humidifier

= 29.3 kJ/kg
= 42.3 kJ/kg
= 24.5C
= 0.817 m3/kg
= 22.03kg/min.
= ma(h2 h1)
= 4.77 kJ/s or 4.77 kW
= 32.8 C
= ma( 2 1)
= 2.379 kg/h

9. Two streams of air 25 C, 50% RH and 25 C, 60% RH are mixed adiabatically to obtain 0.3 kg/s of dry
air at 30 C. Calculate the amounts of air drawn from both the streams and humidity ratio of the mixed
air.
Hint:
Locate the conditions of air in the psychrometric chart and use the below relation to obtain amount of air
and humidity ratio of the resultant air.

10. An air-conditioned room requires 30 m3/min of air at 1.013 bar, 20 C, 52.5% RH. The steady flow
conditioner takes in air at 1.013 bar, 77% RH, which it cools to adjust the moisture content and reheats to
room temperature. Find the temperature to which the air is cooled and thermal loading on both the cooler
and heater. Assume that a fan before the cooler absorbs 0.5 kW, and that the condensate is discharged at
the temperature to which the air is cooled.
Hint:
Locate the initial condition and required indoor condition in psychrometric chart.
St. Josephs College of Engineering / St. Josephs Institute of Technology

31

Temperature to which air is cooled


Thermal loading on cooler
Thermal loading on heater

= 10C
= 25 kW
= 6.04 kW

11. In an engine cylinder, a gas has a volumetric analysis of 13% Co2, 12.5% O2 and 74.5% N2. The
temperature at the beginning of expansion is 950C and the gas mixture expands reversibly through a
volume ratio of 8:1, according to the law PV1.2= constant. Calculate per kg of gas: (a) The workdone, (b)
The heat flow, (c) Change of entropy per kg of mixture.
The values of cp for the constituents Co2, O2 and N2 are 1.235 kJ/kg K, 1.088 kJ/kg K and 1.172 kJ/kg K
respectively.
[NOV/DEC 2015]
Hint:
Calculate initial volume of the mixture and gas constant.
Volume ratio is the expansion ratio of the process.
W = (p1V1 p2V2 )/n-1

12.i.A sling psychrometer in a laboratory test recorded the following readings:


Dry bulb temperature = 35C
Wet bulb temperature = 25C
Calculate the following: (i) Specific humidity (ii) Relative humidity (iii) Vapour density in air (iv) Dew
point temperature (v) Enthalpy of mixture per kg of dry. Take atmospheric pressure = 1.0132 bar.
ii. Write short notes on mixing of air streams adiabatically.
[NOV/DEC2015]
Hint:
i) Plot the given condition of air in psychrometric chart and find the properties.
Or use the following formulae:

ii) Mixing of air streams:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

13. Atmospheric air at 1.0132 bar has a DBT of 30C and WBT of 25C. Compute: (a) The partial pressure
of water vapour, (b) Specific humidity, (c) Dew point temperature, (d) Relative humidity, (e) Degree of
saturation, (f) Density of air in the mixture, (g) Density of vapour in the mixture, (h) Enthalpy of
the mixture. Use thermodynamic tables only.
[APR/MAY 2015]
Hint:

14. A gas mixture contains 7 kg of nitrogen and 2 kg of oxygen at 4 bar and 27C. Calculate the mole
fraction, partial pressures, molar mass, gas constant, volume and density.
[APR/MAY 2015]
Hint:
St. Josephs College of Engineering / St. Josephs Institute of Technology

31

15. A mixture of hydrogen (H2) and oxygen (O2) is to be made so that the ratio of H2 to O2 is 2:1 by volume.
If the pressure and temperature are 1 bar and 25 C Respectively. Calculate (i) the mass of O2 required,
(i) the volume of the container.
[NOV/DEC 2014]
Hint:
Calculate mass fraction and molar fraction and gas constant of the mixture.
Find volume of the mixture by characteristic gas equation.
16.120 m3 of air per minute at 35 C DBT and 50% relative humidity is cooled to 20 C DBT by passing
through a cooling coil. Determine the following (i) relative humidity of out coming air and its wet bulb
temperature (ii) capacity of cooling coil in tones of refrigeration (iii) amount of water vapour removed per
hour.
[NOV/DEC 2014]
Hint:
Plot the conditions of air in psychrometric chart.
Find RH and WBT from the chart.
Calculate mass flow rate.
Capacity of cooling coil is the difference of enthalpy and 1 TR = 3.5 kW.
Amount of water vapour removed is the difference of specific humidity.
17. An air-water vapour mixture enters an air-conditioning unit at a pressure of 1 bar, 38 C DBT, and a
relative humidity of 75%. The mass of dry air entering is 1 kg/s. The air-vapour mixture leaves the air
conditioning unit at 1 bar, 18 C, 85% relative humidity. The moisture condensed leaves at 18 C.
Determine the heat transfer rate for the process.
[NOV/DEC 2014]
Hint:
Find the mass of water vapour with the value of relative humidity.
Find mass flow rates of air in each stream.
Amount of heat transferred is the difference in enthalpy of condition 1 and 3.
18. It is required to design an air-conditioning system for an industrial process for the following hot and wet
summer conditions.
Outdoor conditions
32C DBT and 65% RH
Required air inlet conditions
25C DBT and 60% RH
Amount of free air circulated
250 m3/min
Coil dew temperature
13C
The required condition is achieved by first cooling and dehumidifying and then by heating. Calculate the
following (solve this problem with the use of psychrometric chart).
i.
The cooling capacity of the cooling coil and its by-pass factor.
ii.
Heating capacity of heating coil in kW and surface temperature of heating coil if the by-pass
factor is 0.3
iii.
The mass of water vapour removed per hour
[NOV/DEC 2014]
Hint:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

Locate the points 1, 5 and 3 as shown on psychrometric chart.


Join the line 1-5 and draw constant specific humidity line through 3 which cuts the line 1-5 at point
2.
From psychrometric chart :
h1 = 82.5 kJ/kg, h2 = 47.5 kJ/kg
h3 = 55.7 kJ/kg, h5 = 36.6 kJ/kg
W1 = 19.6 gm/kg, W3 = 11.8 gm/kg
tdb2 = 17.6C,
vs1 = 0.892 m3/kg.
The mass of air supplied per minute = 280.26 kg/min
The capacity of the cooling coil = 42.04 TR
The heating capacity of the heating coil= ma (h3 h2) = 2298.13 kJ/min = 38.3 kW
19. i. Air at 20C, 40% R.H is mixed with air at 40 C, 40% R.H in the ratio of (former) 1:2 (later) on dry
basis. Determine the final condition of air.
ii. Briefly discuss about evaporative cooling process. [NOV/DEC 2013]

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

Evaporative cooling process:

20.i. Derive the sensible heat factor for cooling and dehumidification process. Also explain the process.
ii. One kg of air at 40 C dry bulb temperature and 50% relative humidity is mixed with 2 kg of air at
20C dry bulb temperature and 20 C dew point temperature. Calculate the temperature and specific
humidity of the mixture.
[APR/MAY 2013]
Hint:
i) Cooling and dehumidification: When moist air is cooled below its dew-point by bringing it in contact
with a cold surface as shown in Fig.28.3, some of the water vapor in the air condenses and leaves the air
stream as liquid, as a result both the temperature and humidity ratio of air decreases as shown. This is the
process air undergoes in a typical air conditioning system. Although the actual process path will vary
depending upon the type of cold surface, the surface temperature, and flow conditions, for simplicity the
process line is assumed to be a straight line. The heat and mass transfer rates can be expressed in terms of
the initial and final conditions by applying the conservation of mass and conservation of energy equations
as given below: By applying mass balance for the water:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

ii) Hint:

21.

i. Prove that specific humidity of air is =0.622 /


ii. With the aid of model psychometric chart explain the following processes.
a. Adiabatic mixing
b. Evaporative cooling
i) Hint:

St. Josephs College of Engineering / St. Josephs Institute of Technology

[May/June 2013]

31

ii) Hint:
a. Adiabatic mixing (Refer Q. No. 12. ii)
b. Evaporative cooling process:

22. A tank of 0.2 m3 capacity contains O2 at 15 bar and 400 C. A second tank of 0.5 m3 contains N2 at 20 bar
and 300 C. The two tanks are connected together and allowed to mix. The heat lost during mixing is 50 kJ.
Determine the final pressure, final temperature of the mixture and net entropy change due to mixing.
[APR/MAY 2012]
Hint:
The mole numbers have to be determined using characteristic gas equation.
Heat lost is 50 kJ.
Change in internal energy = [mCv(Tf - Ti)]Nitrogen + [mCv(Tf - Ti)]Oxygen = 50 (for finding final temperature of the
mixture)
For final pressure of the mixture, use PV = NRuT
Change in entropy of the system is the sum of changes in entropy of each constituent.
23. A mixture of ideal gases consists of 4 kg of nitrogen and 6 kg of carbon dioxide at a pressure of 4 bar and a
temperature of 20C. Find:
a. Mole fraction of each constituent,
b. The equivalent molecular weight of the mixture,
c. Equivalent gas constant of the mixture,
d. Partial pressures and partial volumes,
e. Volume and density of the mixture, and
f. Cp and Cv of the mixture.
[APR/MAY 2012]
If the mixture is heated at constant volume to 50C, find the changes in internal energy, enthalpy and
entropy of the mixture. Find the changes in internal energy, enthalpy and entropy of the mixture if the
heating is done at constant pressure.
Take for CO2 = 1.286 and for N2 = 1.4.
[Nov/Dec 2012] [APR/MAY 2012]
St. Josephs College of Engineering / St. Josephs Institute of Technology

31

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

25. i.One kg of air at 35C DBT and 60% R.H. is mixed with 2 kg of air at 20C DBT and 13C dew point
temperature. Calculate the specific humidity of the mixture.
Solution:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

ii. 90 m3 of air per minute at 20C and 75% R.H. is heated until its temperature becomes 30C. Calculate:
(i) R.H. of the heated air. (ii) Heat added to air per minute.
Solution:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

26.i. For the atmospheric air at room temperature of 30C and relative humidity of 60% determine partial
pressure of air, humidity ratio, dew point temperature, density and enthalpy of air.
Hint:
Dew point temperature and density(reciprocal of specific volume) can be read from psychrometric chart.

ii. Show the processes of adiabatic mixing on a skeleton psychrometric chart and explain the process.
[Nov/Dec 2012]
Solution: Refer Q. No. 12. ii.
27.A rigid tank contains 2 kmol of CO2 gases at 300K and 15Mpa. Estimate the volume of the tank on the
basis of (a) The ideal-gas equation of state, (b) Amagats law and Compressibility factors
[Nov/Dec 2010]
Hint:
Ideal gas equation:
pV=nRT
Compressibility factors: Use compressibility chart to get reduced properties
pV=ZcRT

Amagats law:

28. An insulated rigid tank is divided into two compartments by a partition. One compartment contains 7 kg
of Oxygen gas at 40C and 100kPa, and the other compartment contains 4 kg of nitrogen gas at 20 C and
150kPa. Now the partition is removed, and the two gases are allowed to mix. Determine,
a) The mixture temperature and
b) The mixture pressure after equilibrium has been established.
[Nov/Dec 2010]
Solution:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

29.A 5m x 5m x 3m room contains air at 25C and 100 kPa at a relative humidity of 75 percent. Determine
(a) The partial pressure of dry air, (b) The specific humidity, (c) The enthalpy per unit mass of the dry air,
and (d)The masses of the dry air and water vapour in the room.
[Apr/May 2010]
Solution:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

30. The dry and the wet-bulb temperatures of atmospheric air at 1 atm (101.325 kPa) pressure are measured
with a sling psychrometer and determined to be 25C and 15C respectively. Determine
a) The specific humidity,
b) The relative humidity and
c) The enthalpy of the air using thermodynamic relations.
[Nov/Dec 2010]
Hint:

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

31.Two vessels A and B, both containing nitrogen are connected by a valve which is opened to allow
the contents to mix and achieve an equilibrium temperature of 27C. Before mixing the
following information is known about the gases in two vessels.
Vessel A
Vessel B
P = 1.5 MPa
P = 0.6 MPa
T = 50 C
T = 20 C
Contents = 0.5 kg mol
Contents = 2.5 kg
Calculate the final equilibrium process, and the amount of heat transferred to the surroundings. If the
vessel had been perfectly insulated Calculate the final temperature and pressure which would have been
reached. Take = 1.4.
[May/June 2009]

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

32. An air-conditioning system is to take in outdoor air at 283 K and 30% R.H at a steady rate of 45 m3/min
and to condition it to 298 K and 60 % R.H. The outdoor air is first heated to 295 K in the heating section
and then humidified by the injection of hot steam in the humidity section. Assuming the entire process
takes place at a pressure of 100 kPa, determine (i) the rate of heat supply in the heating section and (ii)
the mass flow rate of the steam required in the humidifying section.
[Nov/Dec 2009]
Hint:

Calculate partial pressure of dry air and water vapour.


Calculate specific volume using characteristic gas equation and the mass flow rate.

Calculate mass of steam using mass balance equation.

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

St. Josephs College of Engineering / St. Josephs Institute of Technology

31

You might also like