Engineering Standard: IPS-E-EL-100

IPS-E-EL-100(1)
ENGINEERING STANDARD
FOR
ELECTRICAL SYSTEM DESIGN
(INDUSTRIAL AND NON-INDUSTRIAL)
FIRST EDITION
FEBRUARY 2012
This Standard is the property of Iranian Ministry of Petroleum. All rights are reserved to the owner.
Neither whole nor any part of this document may be disclosed to any third party, reproduced, stored
in any retrieval system or transmitted in any form or by any means without the prior written consent
of the Iranian Ministry of Petroleum.
Feb. 2012
IPS-E-EL-100(1)
FOREWORD
The Iranian Petroleum Standards (IPS) reflect the views of the Iranian Ministry of Petroleum and are
intended for use in the oil and gas production facilities, oil refineries, chemical and petrochemical
plants, gas handling and processing installations and other such facilities.
IPS are based on internationally acceptable standards and include selections from the items
stipulated in the referenced standards. They are also supplemented by additional requirements
and/or modifications based on the experience acquired by the Iranian Petroleum Industry and the
local market availability. The options which are not specified in the text of the standards are
itemized in data sheet/s, so that, the user can select his appropriate preferences therein.
The IPS standards are therefore expected to be sufficiently flexible so that the users can adapt
these standards to their requirements. However, they may not cover every requirement of each
project. For such cases, an addendum to IPS Standard shall be prepared by the user which
elaborates the particular requirements of the user. This addendum together with the relevant IPS
shall form the job specification for the specific project or work.
The IPS is reviewed and up-dated approximately every five years. Each standards are subject to
amendment or withdrawal, if required, thus the latest edition of IPS shall be applicable
The users of IPS are therefore requested to send their views and comments, including any
addendum prepared for particular cases to the following address. These comments and
recommendations will be reviewed by the relevant technical committee and in case of approval will
be incorporated in the next revision of the standard.
Standards and Research department

No.17, Street14, North kheradmand
Karimkhan Avenue, Tehran, Iran .
Postal Code- 1585886851
Tel: 88810459-60 & 66153055
Fax: 88810462
Email: Standards@ nioc.ir
Feb. 2012
IPS-E-EL-100(1)
GENERAL DEFINITIONS
Throughout this Standard the following definitions shall apply.
COMPANY :
Refers to one of the related and/or affiliated companies of the Iranian Ministry of Petroleum such as
National Iranian Oil Company, National Iranian Gas Company, National Petrochemical Company
and National Iranian Oil Refinery And Distribution Company.
PURCHASER :
Means the Company" where this standard is a part of direct purchaser order by the Company,
and the Contractor where this Standard is a part of contract document.
VENDOR AND SUPPLIER:

Refers to firm or person who will supply and/or fabricate the equipment or material.
CONTRACTOR:
Refers to the persons, firm or company whose tender has been accepted by the company.
EXECUTOR :
Executor is the party which carries out all or part of construction and/or commissioning for the
project.
INSPECTOR :
The Inspector referred to in this Standard is a person/persons or a body appointed in writing by the
company for the inspection of fabrication and installation work.
SHALL:
Is used where a provision is mandatory.
SHOULD:
Is used where a provision is advisory only.
WILL:
Is normally used in connection with the action by the Company rather than by a contractor,
supplier or vendor.
MAY:
Is used where a provision is completely discretionary.
Feb. 2012
CONTENTS:
IPS-E-EL-100(1)
Page No.
1. SCOPE ............................................................................................................................................ 4
2. REFERENCES ................................................................................................................................ 4
3. UNITS .............................................................................................................................................. 5
4. ENVIRONMENTAL AND SITE CONDITIONS ............................................................................... 5
5. GENERAL ....................................................................................................................................... 6
5.1 Definitions ................................................................................................................................ 6
5.2 Operational Safety and Reliability ....................................................................................... 11
5.3 Certificates, Declarations and Test Reports ...................................................................... 11
5.4 Quality Assurance and Control ........................................................................................... 12
5.5 Standards, Codes and Regulations .................................................................................... 12
5.6 Document List ....................................................................................................................... 12
6. BASIC ELECTRICAL SYSTEM DESIGN CONSIDERATION ..................................................... 12
6.1 Industrial Electrical System ................................................................................................. 12
6.2 Non-industrial electrical systems ........................................................................................ 40
6.3 Electrical Apparatus for Potentially Explosive Gas Atmospheres .................................. 51
7. DESIGN AND SELECTION REQUIREMENTS FOR EQUIPMENT ............................................. 51
7.1 Electric Network Supply and Emergency Systems (Diesel Generator ) ...................... 51
7.2 Switchgear, Controlgear and Substations ......................................................................... 62
7.3 Transformers ......................................................................................................................... 72
7.4 Electrical motors .................................................................................................................. 82
7.5 Electrical Protection, Metering & Control ........................................................................... 84
7.6 Batteries, Chargers and UPS ............................................................................................. 101
7.7 Power Cables ...................................................................................................................... 108
7.8 Static power factor correction equipment ........................................................................ 115
7.9 Overhead Lines ................................................................................................................... 117
7.10 Lighting ............................................................................................................................. 117
7.11 Earthing, Bonding and Lightning Protection ................................................................. 124
APPENDICES:
APPENDIX A DOCUMENT LIST .................................................................................................. 134
Feb. 2012
IPS-E-EL-100(1)
1. SCOPE
This recommendation covers the minimum requirements which shall be considered in design of
electrical systems in oil, gas, and petrochemical industries. It deals with planning, selection of
equipment, economics of design and hints to be taken care in operation and maintenance. It
describes criteria in selection of system voltage, fault consideration and discusses the safety and
protection of electrical system.
Note:
This is a revised version of this standard, which is issued as revision (1)-2012. Revision (0)1997 of the said standard specification is withdrawn.
2. REFERENCES
a) This recommendation is based on IEC standards and the following standards have been referred
in this document.
b) The following IPS standards may be referred in detail design engineering when required.
IPS
(IRANIAN PETROLEUM STANDARDS)

IPS-C-EL-115 (1)
Construction Standard for Electrical Installation
IPS-M-EL-131 (2)
Material and Equipment Standard for Low Voltage Induction Motors
IPS-M-EL-132 (2)
Material and Equipment Standard for Medium and High Voltage

Induction Motors
IPS-E-EL-110 (1)
Engineering Standard for Hazardous Area
IPS-M-EL-138 (0)
Materials and Equipment Standard for Synchronous Generators
IPS-E-EL-160 (1)
Engineering Standard for Overhead Transmission & Distribution

Lines
IPS-I-EL-215 (1)
Procedure for Initial & Periodical Inspection in Potentially Explosive

Atmospheres (Hazardous Area)
IPS-M-EL-136 (1)
Material and Equipment Standard for Rotating Electrical Machines

Direct Current Motors
IPS-M-EL-138 (0)
Material and Equipment Standard for Synchronous Generators
IPS-I-EL-217 (0)
Inspection Standard for Pre-commissioning Electrical Tests
IPS-M-EL-143 (2)
Material and Equipment Standard for Low Voltage Switchgear and

Control gear
IPS-M-EL-144 (1)
Material and Equipment Standard for Medium and High Voltage

Switchgear and Controlgear
IPS-M-EL-181 (2)
Material and Equipment Standard for Power Factor Improvement

Capacitor
IPS-M-EL-151 (1)
Dry Type Power Transformers
IPS-M-EL-152 (2)
Oil Immersed Power Transformers
IPS-M-EL-190 (1)
Material Standard for Electrical Heat Tracing
IPS-M-EL-165 (0)
Material and Equipment Standard for Low Voltage Industrial and

Flameproof AC Motor Control Centers (MCC)
IPS-M-EL-220 (1)
Material and Equipment Standard for Current Limiting Reactors
IPS-M-EL-174 (2)
Material and Equipment Standard for Battery and Battery Charger

(DC Power supply)
Feb. 2012
ISO
IPS-E-EL-100(1)
IPS-M-EL-176
Material and Equipment Standard for Uninterruptible Power Supply

(UPS)
IPS-M-EL-240 (0)
Material and Equipment Standard for Low Voltage Industrial and

Flameproof AC Switch-Fuse Assembly
IPS-M-EL-271 (1)
Material Standard for Low Voltage Cables & Wires
IPS-M-EL-272 (1)
Material Standard for Medium and High Voltage Power Cables
IPS-M-EL-273 (1)
Material Standard for Sub Marine Power Cables with Inherent Optical
Fibers
(INTERNATIONAL ORGANIZATION FOR STANDARDIZATION)

ISO 12332
Code of practice for Ventilation in Petrochemical Plants and

Refineries
NFPA (NATIONAL FIRE PROTECTION ASSOCIATION)

NFPA 76
Fire Protection for Telecommunication facilities
NFPA 70
Electrical Safety Requirements for Employee Workplaces
ASHRAE (AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING

ENGINEERS)
ASHRAE 62
BSI
Ventilation for Acceptable Indoor Air Quality
(BRITISH STANDARDS INSTITUTION)

EN 50272-2
Safety requirements for Secondary Batteries and Battery Installations
IEEE (INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS)

IEEE Guide for Substation Fire Protection IEEE Std 979-1994
3. UNITS
This Standard is based on International System of Units (SI), as per IPS-E-GN-100 except where
otherwise specified.
4. ENVIRONMENTAL AND SITE CONDITIONS
The following are the minimum typical information that shall be completed in conjunction with the
environmental conditions before engineering work proceeds on:
1) Site elevation ....................................... m above sea level
2) Maximum ambient temperature............................................. C
3) Minimum ambient temperature.............................................. C
4) Minimum relative humidity.............................. %
5) Atmosphere: Saliferrous, dust corrosive and subject to dust storms with concentration of 70-1412
mg/m, H2S may be present unless otherwise specified.
6) Lightning storms: Isoceraunic level......... storm-day/year
7) Earthquake zone.................................................
8) Wind direction (where relevant).........................................
9) Area classification (where applicable)
Feb. 2012
IPS-E-EL-100(1)
5. GENERAL
5.1 Definitions
For the purpose of this standard, the following definitions apply:
Autonomy time (of a battery)

The autonomy time is the duration for which the battery can supply its rated load within its specified
voltage limits, following a prolonged period (i.e. not less than one year) of battery float-charge
operation.
Certificate
Document issued by a recognized authority certifying that it has examined a certain type of
apparatus and, if necessary, has tested it and concluded that the apparatus complies with the
relevant standard for such apparatus.
Certificate of conformity
Certificate stating that the electrical apparatus complies with the relevant standards for apparatus
for potentially explosive atmospheres.
Declaration of compliance
Document issued by the manufacturer declaring that the electrical apparatus complies with the
requirements of IEC 60079-15.
Distribution of electricity
The transfer of electricity to consumers within an area of consumption.
Electrical installation
Civil engineering works, buildings, machines, apparatus, lines and associated equipment used for
the generation, conversion, transformation, transmission, distribution and utilization of electricity:
Electrical power system

All installations and plants provided for the purpose of generating, transmitting and distributing
electricity.
Emergency Lighting
Lighting provided for use when the supply to the normal lighting fails.
Escape Lighting
That part of the emergency lighting which is provided to ensure that the escape route is illuminated
at all material times.
Feb. 2012
IPS-E-EL-100(1)
Essential service
A service, which, when failing in operation or when failing if called upon, will affect the continuity,
the quality or the quantity of the product.
Firm capacity
The installed capacity less than stand-by capacity.
Frequency deviation
The difference between the system frequency at a given instant and the nominal value.
Hazardous area
An area in which an explosive gas atmosphere is or may be expected to be present in quantities
such as to require special precautions for the construction, installation and use of electrical
apparatus.
Installed capacity
The sum of the rated powers of equipment of the same kind (generators, transformers, converters,
etc.) in an electrical installation.
Low voltage (LV)

A set of voltage levels used for the distribution of electricity and whose upper limit is 1000 V AC
Non-essential service
A service that is neither vital nor essential.
Non-hazardous area
An area in which an explosive gas atmosphere is not expected to be present in quantities such as
to require special precautions for the construction, installation and use of electrical apparatus.
Point of common coupling (PCC)

The point of coupling at the public utility networks, to which the system under consideration is, or is
to be, connected.
Rated value
A quantity value assigned, generally by the manufacturer, for a specific operating condition of a
component, device or equipment.
Site conditions
The external factors, e.g. altitude, air temperature, wind velocity, vibrations, earthquakes, black
body temperature, relative humidity, etc., which may influence the operation of a machine or
apparatus.
Feb. 2012
IPS-E-EL-100(1)
Spare capacity
The difference between firm capacity and the maximum calculated (peak) load.
Stand by capacity
The capacity provided for the purpose of replacing that which may be withdrawn from service under
planned or unplanned circumstances.
Test report
Document prepared by the manufacturer indicating in detail the tests and verifications to which the
electrical apparatus has been subjected, and their results.
Uninterruptible power supply

A source of electrical power which is backed up by a second (emergency) source of power, such as
to provide a supply of electricity that may be interrupted for no more than 0.5 ms.
Vital service
A service which, when failing in operation or when failing if called upon, can cause an unsafe
condition of the process and/or electrical installation, jeopardize life, or cause major damage to the
installation.
Voltage deviation
The difference, generally expressed as a percentage, between the voltage at a given instant at a
point in the system, and a reference voltage such as nominal voltage, a mean value of operating
voltage, or declared supply voltage.
Voltage dip
A sudden reduction of the voltage at a point in the system, followed by voltage recovery after a
short period of time, from a few cycles to a few seconds.
Voltage surge
A transient voltage wave propagating along a line or a circuit and characterized by a rapid increase
followed by a slower decrease of the voltage.
Zone 0 (in the classification of hazardous gas areas)

An area in which an explosive gas atmosphere is present continuously, or is present for long
periods.

An area in which an explosive gas atmosphere is likely to occur in normal operation.

An area in which an explosive gas atmosphere is not likely to occur in normal operation and if it
does occur it will exist for a short period only.
Feb. 2012
IPS-E-EL-100(1)
Zone 21 (in the classification of hazardous dust areas)

An area in which combustible dust is present or may be present as a cloud during normal
processing, handling, or cleaning operations in sufficient quantity that it is capable of producing an
explosive concentration of combustible or ignitable dust in mixtures with air.
Note:
A dust layer maybe present and should be taken into account.
Zone 22 (in the classification of hazardous dust areas)

Areas, not classified as Zone 21, in which ignitable dust clouds may occur infrequently and persist
for only a short period, or in which accumulations or layers of combustible or ignitable dust may be
present under abnormal conditions and give rise to ignitable mixtures of dust in air. Where, following
an abnormal condition, the removal of dust accumulations or layers cannot be assured, the area
shall be classified as Zone 21.
Note:
This zone can include areas in the vicinity of apparatus containing dust, from which, dust
can escape from leaks and form dust deposits in hazardous areas.
Bus coupler circuit breaker

In a substation a circuit breaker which is located between two busbars and which permits the
busbars to be coupled; it may be associated with selectors in case of more than two busbars.
Bus section circuit breaker (= switched busbar circuit breaker)

In a substation a circuit breaker, connected in series within a busbar, between two busbar sections.
Controlgear
A general term covering switching devices and their combination with associated control,
measuring, protective and regulating equipment, also assemblies of such devices and equipment
with associated interconnections, accessories, enclosures and supporting structures, intended in
principle for the control of electric energy consuming equipment.
Converter
An operative unit for electronic power conversion comprising one or more electronic valve devices,
e.g. thyristors, associated firing and control circuits and, if necessary, filters and auxiliaries.
Distribution substation/switchboard
A substation/switchboard mainly used for distributing power to several plant substations.
Generating set
A group of rotating machines transforming mechanical or thermal energy into electricity.
Generator
A machine which converts mechanical power into electrical power.
9
Feb. 2012
IPS-E-EL-100(1)
Intake substation/switchboard
A substation/switchboard at which the supply provided by the public utility is interconnected with the
site's electrical distribution system.
Note:
An intake substation and a power plant substation may be combined as a single substation.
Inverter
A converter for conversion from DC to AC
Plain feeder
A feeder which consists of a cable or an overhead line only and does not have. An interconnected
transformer.
Plant substation/switchboard
A substation/switchboard mainly used for feeding one process or utility plant.
Power plant substation/switchboard

A substation/switchboard to which generators and outgoing feeders are connected.
Note:
An intake substation and a power plant substation may be combined as a single substation.
Power station (power plant)

An installation whose purpose is to generate electricity and which includes civil engineering works,
energy conversion equipment and all the necessary ancillary equipment.
Power transformer
A static piece of apparatus with two or more windings which, by electromagnetic induction,
transforms a system of alternating voltage and current into another system of voltage and current
usually of different values and at the same frequency for the purpose of transmitting electrical
power.
Rectifier
A converter for conversion from AC to DC.
Remote control unit (RCU)

A control device in the vicinity of a consumer for operation of the remotely installed controlgear of
the consumer.
10
Feb. 2012
IPS-E-EL-100(1)
Substation (of a power system)

The part of a power system, concentrated in a given place, including mainly the terminations of
transmission or distribution lines, switchgear and housing and which may also include transformers.
It generally includes facilities necessary for system security and control (e.g. the protective devices).
Switchgear
A general term covering switching devices and their combination with associated control,
measuring, protective and regulating equipment, also assemblies of such devices and equipment
with associated interconnections, accessories, enclosures and supporting structures, intended in
principle for use in connection with generation, transmission, distribution and conversion of electric
power.
Switch room
A room in a substation or building intended exclusively for the installation of one or more
switchboards, distribution boards etc.
Variable speed drive system (VSDS)

A line-fed AC to AC conversion system consisting of all facilities required to operate its electric
motor at variable speeds.
5.2 Operational Safety and Reliability

The design of the electrical installation shall be based on the provision of a safe and reliable supply
of electricity at all times. Safe conditions shall be ensured under all operating conditions, including
those associated with start-up and shutdown of plant and equipment, and throughout the
intervening shutdown periods.
The design of electrical systems and equipment shall ensure that all operating and maintenance
activities can be performed safely and conveniently and shall permit periods of continuous operation
of at least 4 years. To fulfill the above requirements provisions may be required for alternative
supply sources and supply routes, spare/stand-by capacity, load shedding and automatic restarting
schemes, etc.
The simultaneous failure of two pieces of equipment shall not be catered for.
The insulating and dielectric materials used in all electrical equipment shall be non-toxic and shall
not contain compounds that are persistent and/or hazardous environmental contaminants. e.g.
polychlorinated biphenyls (PCBs).
The design of the electrical installation shall ensure that access is provided for all operational and
maintenance purposes.
Special attention shall be paid to provisional and temporary installations required for the erection of
permanent installations to ensure compliance with basic rules for good working practice and safety
and to cope with increased hazards which are present in temporary installations.
5.3 Certificates, Declarations and Test Reports

For all major equipment, the Contractor shall obtain at least the manufacturer's test reports in
accordance with the equipment specifications, e.g. for generators, motors, VSDS, HV ;MV; LV
switchgear, UPS equipment, and transformers.
Further certificates or declarations relating to the application of equipment for use in hazardous
areas may be required by local authorities, according to the following rules:
11
Feb. 2012
IPS-E-EL-100(1)
For electrical apparatus in Zone 0, Zone 1 and Zone 2 areas, a certificate of conformity shall be
obtained from the Manufacturer; For electrical apparatus in Zone 2 areas, which has type of
protection 'n', a declaration of compliance may be accepted instead of a certificate of conformity.
5.4 Quality Assurance and Control

Contractors and suppliers shall demonstrate to the Principal that they implement quality control and
assurance systems which conform to the ISO 9001:2000 series and shall be approved by company
representative.
5.5 Standards, Codes and Regulations

This recommendation is based on the publications of the International Electro technical Commission
(IEC), where relevant the specific publications are referenced in this recommendation.
The design and engineering of the electrical installation shall satisfy all statutory requirements of the
national and/or local authorities of the country in which the electrical installation will be located.
The electrical installation shall be suitable for the site conditions as specified by the Principal.
Where necessary special attention shall be paid to the selection and installation of electrical
equipment suitable for seismic conditions.
Furthermore, the contents of this recommendation and of standards and publications referred to
herein shall be adhered to, except where amended by specific requirements given by the Principal
relating to a particular installation, and as far as is permitted under the statutory requirements
mentioned above.
Electrical equipment and materials shall comply with the relevant standard and/or MESC (Group
Materials and Equipment Standards and Code) specifications, which in turn shall be considered as
supplementary to IEC equipment standards.
CENELEC or national standards of the country in which the installation will be located may be used
in lieu of IEC standards for the design and engineering of the electrical installation, provided they
are not less stringent in their total requirement.
In the event of contradiction between the requirements of recommendation specifications and IEC.
national standards, the former shall prevail, subject to satisfying statutory obligations in the country
of installation.
In the event of contradiction between the requirements of this recommendation and those of
specifications referenced in this recommendation, the more recently published document shall
prevail, except where otherwise specified by the Principal for a particular installation.
In some cases, other standards except IEC standard could be used, so these standards shall be
approved by company representative.
5.6 Document List

The project documents in the basic and detail design shall be included as the Appendix A.
6. BASIC ELECTRICAL SYSTEM DESIGN CONSIDERATION
6.1 Industrial Electrical System
6.1.1 Basic design consideration
12
Feb. 2012
IPS-E-EL-100(1)
6.1.1.1 General
Minimum required Documents for basic and detail design shall be accordance with "Appendix A".
6.1.1.1.1 Safety
Safety takes to form: Safety to personnel, safety to materials, building and safety to electric
equipment.
Safety to personnel involves no compromise, only the safest system can be considered. Safety to
materials. Buildings and electric equipment may involve some compromise when safety of
personnel is not jeopardized. In general:
Safe and reliable supply of electrical supply electricity should be designed.
Safe condition for start-up and shut-down of plant shall be provided.
Safety of personnel and equipment during operation and maintenance shall be considered.
6.1.1.1.2 Continuity of service

The electrical system should be designed to isolate faults with a minimum of disturbance to the
system and should feature to give the maximum dependability consistent with the plant
requirements.
6.1.1.1.3 Voltage regulations

For some plant power system, voltage spread may be the determining factor of the distribution
design. Poor regulation is detrimental to the life and the operation of electric equipment.
The voltage regulation of system shall not exceed 5% for HV., MV. and LV. main bus bar.
6.1.1.1.4 Plant expansion

Plant load generally increase, consideration of the plant voltages, rating of equipment, space for
additional equipment and capacity for increased load must be included according to client
requirements.
While the power capacity of a system is increased compatibility of fault level of existing installation
shall be carefully scrutinized in conjunction with new available fault level.
6.1.1.1.5 Other requirements

The following principles also shall be considered in design of electrical systems:
The insulating materials used shall be non-toxic or hazardous environmental contaminants. Use of
electrical equipments in hazardous area should be minimized. Access to electrical installations for
the purpose of operational and maintenance shall be ensured. Equipment of similar natures and
identical construction should be of the same manufacturer. Test reports for all electrical equipments
shall be provided. Certification for equipments used in hazardous areas shall be provided.
6.1.1.2 Planning guide for distribution design

With the above mentioned factors in mind, the following procedure is given to guide the engineer in
the design of an electric system for any industrial plant.
6.1.1.2.1 Obtain a general layout and mark it with the major loads at various locations and
determine the approximate total plant load in horsepower, kilowatts, and kilo volt-amperes.
Estimate the lighting, air-conditioning, and other loads from known data.
13
Feb. 2012
IPS-E-EL-100(1)
6.1.1.2.2 Determine the total connected load and calculate the maximum demand by using demand
and diversity factors.
6.1.1.2.3 Investigate unusual loads, such as the starting of large motors, or welding machines, and
operating conditions such as boiler auxiliary motors, loads that must be kept in operation under all
conditions, and loads that have a special duty cycle.
6.1.1.2.4 Investigate the various types of distribution system and select the system or systems best
suited to the requirements of the plant. Make a preliminary one line diagram of the power system.
6.1.1.2.5 If power is to be purchased from the utility, obtain such information concerning the supply
system or systems as:
performance data, voltage available, voltage spread, type of systems available, method of system
neutral grounding, and other data such as relaying, metering and the physical requirements of the
equipment. The interrupting rating and momentary ratings of power circuit breakers should be
obtained as well as the present and future short-circuit capabilities of the utility system at the point
of service to the plant. Investigate the utilitys power contract to determine if off-peak power at lower
rates available, and any other requirements, such as power factor and demand clauses, that can
influence power cost.
6.1.1.2.6 If considering a generating station for an industrial plant, such items should be determined
as : generating KVAR required including standby loads, generating voltage, and such features as
relaying, metering, voltage regulating equipment, synchronizing equipment and grounding
equipment. If parallel operation is contemplated, be sure to review this with the utility and obtain its
requirements.
6.1.1.2.7 A cost analysis may be required of the different voltage levels and various arrangements
of equipment to justify and properly determine the voltage and equipment selected. The study
should be made on the basis of installed cost including all the components in that section of the
system.
6.1.1.2.8 Check the calculations of short-circuit requirements to be sure that all breakers are of the
correct rating. Review the selectivity of various protective devices to assure selectivity during load
or fault disturbances.
6.1.1.2.9 Calculate the voltage spread and voltage drop at various critical points.
6.1.1.2.10 Determine the requirements of the various components of the electric distribution system
with special attention given to special operating and equipment conditions.
6.1.1.2.11 Review all applicable national and local codes for requirements and restrictions.
6.1.1.2.12 Check to see that the maximum safety features are incorporated in all parts of the
system.
6.1.1.2.13 Write specification on the equipment and include a one-line diagram as a part of the
specifications.
14
Feb. 2012
IPS-E-EL-100(1)
6.1.1.2.14 Obtain typical dimensions of equipment and make drawings of the entire system.
6.1.1.2.15 Determine if the existing equipment is adequate to meet additional load requirements.
Check such ratings as voltage, interrupting capacity, and current-carrying capacity.
6.1.1.2.16 Determine the best method of connecting the new part of the power system with the
existing system so as to have a minimum outage at minimum cost. Naturally the above procedure
will not automatically design the electric power system in itself; it must be used with good, sound,
basic engineering judgment.
6.1.1.3 General layout

A general layout of the plant should be available before the engineer can begin his study. This
layout usually gives the location and the size of the proposed building or buildings in the initial
particular project. The extent of the available layout gives the engineer an idea of the possible
expansion of the plant in the future, and must be considered by the engineer in planning the electric
distribution system.
6.1.1.4 Type of circuit arrangements

Load centers shall be employed as far as possible and the main busbars shall be fed from both
sides.
6.1.1.5 Flexibility
Flexibility for expansion should be considered. In line with this, the engineer should strive for a
system design that will permit reasonable expansion with minimum downtime to existing production.
6.1.1.6 System reliability

The system shall be designed so that, when one fault occurs the operation of the system will not be
jeopardized.
6.1.1.7 Selection of equipment

The fundamental consideration in selecting equipment is to choose optimum equipment consistent
with the requirements of the plant. Frequently it costs no more in the long run to use the best
equipment available as it pays dividends in service continuity and lower maintenance. Some widely
accepted principles are:
6.1.1.7.1 Use metal enclosed for 400 volt indoor switchgear and metal clad for outdoor.
6.1.1.7.2 Choose dry type transformers for indoor installations in non-process areas.
6.1.1.7.3 Use factory assembled equipment for easier field installation and better coordination as far
as possible.
6.1.1.7.4 Rating and sizing

a) The rating of equipment shall be as per IEC recommendation.
b) For sizing of equipment refer to section "7. Design And Selection Requirements For Equipment"
6.1.1.7.5 Be sure equipment complies with requirement of pertinent hazard classification.
15
Feb. 2012
IPS-E-EL-100(1)
6.1.2 Load
6.1.2.1 Rating and Diversity Factors
6.1.2.1.1 Electrical equipment shall be rated to carry continuously the maximum load associated
with peak design production with an additional 20% contingency.
The ambient condition at which this rating applies shall be defined in equipment specifications and
unless otherwise approved by client shall not be less than 40C maximum air temperature at an
altitude not exceeding 1000 m above sea level.
6.1.2.1.2 Assessment of maximum load requirements of an installation shall allow for diversity
between various loads, drives or plants. The diversity factors used shall consider the coincidentally
requiring peak demands and shall be based on similar installations whenever possible. The use of
diversity factors shall result in "After Diversity Maximum Demands" (ADMD) being used for design
purposes.
6.1.2.2 Types of loads
6.1.2.2.1 Basic types
a) Dynamic: These are electric motors driving rotating equipment.

b) Static: These are non moving types of electrical equipment such as lighting, heating and
supplies to rectifiers etc.
The bulk of the loads on the majority of installations comprise dynamic loads and the proportion of
dynamic loads to static loads is generally high and varies under different circumstances.
6.1.2.2.2 Critical loads

These are loads of prime importance to the safety of the installation or the operational staff, and
which require power to permit their safe shutdown in emergency. They shall have a second
independent power source and be generally associated with no break supplies. In certain cases, a
short supply break may be acceptable if this does not represent a hazard to safety.
6.1.2.2.3 Essential loads

These are loads whose loss would affect continuity of plant operation resulting in loss of revenue
but would not result in an unsafe situation arising. Any decision to provide an alternative source of
supply for these types of load shall be based on economic considerations as specified by client.
6.1.2.2.4 Non-essential loads

Non-essential loads are those which do not form an important component of a production or
process plant and their disconnection is only of minimal or nuisance value. They usually form a
small proportion of the total connected load and may have a single power source.
16
Feb. 2012
IPS-E-EL-100(1)
6.1.3 Power supply sources
6.1.3.1 General
The power supply system shall be designed to provide safe and economical operation. The safety
aspects should cover both plant and personnel. Economic considerations shall cover capital and
running costs and an assessment of the reliability and consequent availability of the system. The
cost of improved power systems reliability should be weighed against the progressive potential loss
incurred by loss of production. However a technical / economical study should be performed for
power supply source selection.
All negotiations with public utilities shall be the sole responsibility of client.
6.1.3.1.1 Electrical import from a public utility

Where the principal sources of electrical power is selected to be from a public utility, the supply
should be via duplicate feeders.
An exception to this may be permitted for economic reasons where low power loads are to be
supplied from overhead lines and where a single feeder may be employed, provided that on-site
standby generating equipment is available to meet the total load. Critical loads should always be
provided for by on-site standby generating equipment which should only operate in the event of
main supply failure.
Grid intake systems shall be controlled by circuit breakers with the protection, control, alarm,
instruments and relevant meters such as KWH meters and MAX. Demand meters .The design of
these systems should be performed in coordination with public utility.
6.1.3.1.2 On-site generation with no public utility connection

Where a site is offshore, or remote from a public utility network, or has a surplus of fuel or process
energy, on-site generation will normally be selected as the principal source of power. The number
and types of on-site generating sets shall depend on:
i) The fuel source.
ii) The nature of the process energy.
iii) The process steam or other heat requirements, if any
iv) The relationship between electric power requirements and the energy sources on any given site.
v) Economic size
vi) Maintenance requirements
vii) Future development
Unless otherwise agreed by client, a minimum of 3 generating sets, which may include an
emergency generator to supply the critical loads, will be required on sites where there is no
alternative electricity supply. The following criteria shall be satisfied:
- There shall be sufficient generation to meet the "After Diversity Maximum Demand" (ADMD),
when the largest single source of supply is out of service at peak demand times due to
maintenance or any other reason.
- Generation shall be able to cater for the load requiring a supply after automatic load shedding if
provided) when the largest single source of supply is out of service and the second largest single
source is coincidentally shut down due to unforeseen circumstances.
6.1.3.1.3 On site generation run in parallel with a public utility

Where on-site generation is selected to be the principal source of power and where a connection to
a public utility is available, the public utility connection may serve:
17
Feb. 2012
IPS-E-EL-100(1)
i) As a standby source of electric power.

ii) A means of export of surplus electrical power.
iii) A combination of both.
6.1.3.2 Emergency power supply equipment
6.1.3.2.1 Critical loads by definition require a high degree of reliability of supply. This reliability may
be achieved by, in order of preference:
i) Providing another source of energy, such as batteries.
ii) Increasing the amount of normal supply generation equipment.
iii) Ensuring a number of alternative supply feeds is available to the loads.
iv) Providing local standby plant.
In cases where the provision of another source of energy is not practicable, the least cost of the
remaining alternatives should normally be adopted bearing in mind the additional servicing and fuel
requirements associated with standby generation.
6.1.3.2.2 Critical loads shall be supplied by reliable generators or other suppliers during
maintenance of the largest generator at coincidental to the unscheduled outage of the next largest
generator.
6.1.3.2.3 Where increased generating plant or local standby plant is selected to provide power to
critical loads, it shall be either diesel engine or gas turbine driven generator set(s) each with its own
dedicated fuel supply. Secure static power supplies may be selected depending on the nature of the
critical loads being supplied and on fuel availability for generator sets. The emergency equipment
shall be rated to have a spare capacity of 10%. The efficiency of operation of emergency equipment
is not a significant factor but its ability to start reliably and supply the loads under emergency
conditions is critical.
6.1.3.2.4 Emergency generator sets shall be capable of starting and running when no alternative
source of electrical AC power is available i.e., a black start capability. This shall be achieved by
compressed air starting with air receivers being capable of six engine starts from one air charge, or
by battery starting with a similar capability.
6.1.3.2.5 It shall not be possible to connect emergency generators to a load greater than their rated
capacity. Parallel operation of emergency diesel generators with grid supply shall not be permitted
and safe and reliable interlocks shall be considered for that. Manual facilities shall also be provided
for regular testing purposes.
Testing facilities should permit the loading of standby generator sets.
6.1.3.3 Primary substation
6.1.3.3.1 Generator circuits other than local emergency generators and public utility power intakes
shall be connected together at a common primary substation, the busbars of which are used as the
main load distribution center. In certain cases, however, generators and public utility power intakes
may be located at different points throughout the site, in which case there may be a number of
primary substations which shall be interconnected on the site.
6.1.3.3.2 The switchgear for primary substations shall comply with the requirements of
IPS-M-EL-144.
18
Feb. 2012
IPS-E-EL-100(1)
6.1.3.3.3 Busbar arrangements shall be selected to be cost effective, operationally flexible and safe.
The following technical points shall be taken into account:
i) Operational flexibility to permit loads and power supplies to be effectively connected under
schedule and unscheduled outages of circuits and busbar sections.
ii) Minimal switchgear per circuit and simple control and protection.
iii) Unscheduled loss of busbar sections shall not shut down the system beyond the level designed
and provided for.
iv) Scheduled maintenance of busbars shall be possible without system shutdowns beyond those
designed and provided for.
6.1.3.3.4 The location of the primary substations shall be considered in safe areas.
6.1.3.4 Synchronizing
6.1.3.4.1 Synchronizing or check synchronizing equipment shall be provided wherever more than
one source of power may be operated in parallel with another.
6.1.3.4.2 The simplest form of check synchronizing equipment shall comprise voltmeters and
synchroscope to show the voltage and frequency differences between the two systems that need to
be paralleled. A check synchronizing relay may be utilized to prevent operator mal-operation, but in
order to allow closing a power source on to a dead system, as is required under black start
conditions, the check synchronizing relay shall have a means of manual or automatic disconnection.
6.1.3.4.3 Synchronizing or check synchronizing facilities shall be fitted to busbar section and bus
coupler circuit breakers only when it is possible to run the two systems feeding either section of a
busbar completely segregated from the other. The numbers of circuit breakers provided with
synchronizing or check synchronizing facilities shall be kept to a minimum. A similar logic shall be
applied to public utility intake circuits. Alternatively, circuit breaker interlocking schemes shall be
installed to preclude the possibility of paralleling two sources of power where synchronizing facilities
are excluded. Synchronizing facilities shall be provided at the primary power supply voltage and
avoided at other voltages by use of appropriate circuit breaker interlocking.
6.1.3.5 Secondary unit substations
6.1.3.5.1 Application
Secondary unit substations form the heart of all industrial plant electrical distribution systems. They
are used to step down the primary voltage to the utilization voltage at various load centers
throughout the plant. Many factors must be considered when selecting and locating substations.
Most important of these are:
i) Load grouping by KVA
ii) Voltage rating
iii) Service facilities
iv) Safety
v) Ambient conditions
vi) Continuity of service
vii) Aesthetic consideration
viii) Lightning protection requirements
ix) Space available
x) Outdoor vs. indoor location
19
Feb. 2012
IPS-E-EL-100(1)
xi) Plans for future expansion

xii) Safe area location
6.1.3.5.2 Components of secondary unit substations

An articulated secondary unit substation consists of three basic components i.e.:
- Incoming line section
- Transformer section
- Outgoing section
The design principle of which is similar to load centers.
6.1.4 Load center systems

A load-center system may be defined as one in which power is transmitted at voltages above 400
volts to unit substations located close to the centers of electric load. At these substations the
voltage is stepped down to the utilization level and distributed by short secondary feeders to the
points of use. The trend to this type of system has become very marked in recent years. An
examination of the advantages listed below for the load-center system when compared to older
systems will indicate why such a trend has come about.
i) Lower first cost.
ii) Reduced power losses.
iii) Improved voltage regulation.
iv) Increased flexibility.
v) Better continuity of service.
vi) Simplified engineering, planning, and purchasing.
vii) Lower field installation expense.
It should also be pointed out that a contributing factor to the increased use of load center system
has been the development of air circuit breakers, metal-clad and metal-enclosed switchgear, and
especially dry type transformers. These equipments have permitted the installation of the unit
substations in buildings and close to the centers of loads without requiring expensive vaults to
minimize fire hazards and danger to personnel.
6.1.5 Selection of system voltage

The selection of utilization distribution and transmission voltage levels is one of the most important
consideration in power system design. System voltages usually affect the economics of equipment
selection and plant expansion more than any other single factor; it behooves the power system
engineer to consider carefully the problem when designing the distribution system.
6.1.5.1 Voltage levels

The various voltage levels may be broadly defined as follows:
Low voltage (LV): is defined as voltages below 1000 volt in a 3 phase 4 wires, 50 Hz
system.400/230 volt system is adopted as standard voltage for low voltage. However 110 volt ac for
small power or control systems and 25 volt AC for inspection system are common.
Medium voltage (MV): is defined as voltages higher than 1000 volt up to 10 kV in a 3 phase, 3
wires, 50 Hz system. The following voltages may be used depending on technical and economical
considerations, available utility voltages and similar equipments used indifferent locations: 3.3 KV, 6
KV
20
IPS-E-EL-100(1)
Feb. 2012
High Voltage (HV): is defined as 10 kV and higher in a 3 phase, 3 wires, 50 Hz system and it
should be 10 KV, 11 KV, 20 KV, 33 KV, 63 KV, 66 KV, 132 kV and 230 KV. The low voltage is
normally restricted for supplying to utilization equipment directly.
The high and medium voltage is used most frequently for distribution purposes and also is
employed as utilization voltage particularly for motors rated 3.3, 6 and 11 kV.
The high voltages above 20 KV and the high voltages are mainly used for power distribution and or
transmission.
The frequency of power supply systems for onshore systems shall be 50 Hz. For offshore systems
the voltage of power system shall be based on engineering evaluation and decided by company
engineer.
6.1.5.2 The factors affecting system voltage

At least the following points should be considered for voltage selection:
1) service voltage available from utility
2) load magnitude
3) distance the power is transmitted
4) rating of utilization device
5) result of load flow studies
6) safety
7) compatibility with existing installations
6.1.5.3 System voltage variation

An ideal electric power system is one which will supply constant frequency and voltage at rated
nameplate value to every piece of apparatus in the system. In modern power system frequency is a
minor problem but it is impractical to design a power system which will deliver absolutely constant
rated nameplate voltage to every piece of apparatus. Since this cannot be attained what are the
proper limits of voltage in an industrial plant?
This should be determined by the characteristics of the utilization apparatus.
The voltage at incoming terminal shall not deviate more than 5% and the system frequency shall
not deviate from the rated frequency more than 2%. the total harmonic distortion shall not be more
than 8% and each harmonic distortion shall not be more than 5%.
6.1.5.3.1 Permissible voltage drop

Voltage drop in a distribution system is the difference at any instant between the voltages at the
source and utilization end of a feeder branch circuit or transformer. Voltage spread is the difference
between the maximum and minimum voltages existing in any one voltage class system under
specified steady state condition. Voltage regulation is a measure of the change in voltage between
no load and full load in terms of the full load voltage.
(no load voltage) - (full load voltage)

Percent regulation =
100
full load voltage
The electrical power system shall be so designed to limit voltage drop (base on nominal voltage) in
the feeder cables to the following values:
21
Feb. 2012
IPS-E-EL-100(1)
- Feeders to area sub-station
1%
- Feeders from area sub-station
1%
- Motor branch circuit (at full load)
5%
- Power source to panel board
2%
- Lighting circuits from panel board to last lighting fixture
3%
- The maximum voltage drop in the motor feeder cable during motor starting
15%
Note:
The total voltage drop to the terminals of motors shall not exceed 15% of the nominal system
voltage during the motor starting period under the worst conditions of the supply through
the distribution network.
For medium and high voltage motors the cable voltage drop at motor full load shall not exceed
3.25%.
6.1.5.3.2 Improvement of voltage conditions

If voltage condition must be improved the following are suggested lines of consideration:
- Changing circuit constants
- Changing the transformer taps
6.1.5.4 Motor starting voltage drop

It is characteristic of most alternating-current motors that the starting current is much higher than
their normal running current. Synchronous and squirrel-cage induction motors starting on full
voltage may draw a current as high as seven or eight times their full load running current. This
sudden increase in the current drawn from the power system may result in excessive drop in
voltage unless it is considered in the design of the system. The motor starting KVA, imposed on the
power-supply system and the available motor torque are greatly affected by the method of starting
used.
Table 1 gives a comparison of motor starting common methods.
Table 2 shows general effect of voltage variations on induction motor characteristics.
22
IPS-E-EL-100(1)
Feb. 2012
TABLE 1 - COMPARISON OF MOTOR-STARTING METHODS*

Type of Starter
(Settings given are the more common for
each type)
Motor
Terminal Voltage
Line Voltage
Starting Torque
Full-Voltage
Starting Torque
Line Current
Full-Voltage
Starting Current
Full-voltage starter
1.0
1.0
1.0
Auto transformer
80 percent tap
65 percent tap
50 percent tap
0.80
0.65
0.50
0.64
0.42
0.25
0.88
0.46
0.30
0.80
0.64
0.80
0.50
0.45
0.375
0.25
0.20
0.14
0.50
0.45
0.375
Part-winding starter
(low-speed motors only)
75 percent winding
50 percent winding
1.0
1.0
0.75
0.50
0.75
0.50
Star delta starter
0.57
0.33
0.33
Resistor starter, single step

(adjusted for motor voltage to be
80 percent of line voltage)
Reactor
50 percent tap
45 percent tap
37.5 percent tap
* Notes:
1) For a line voltage not equal to the motor rated voltage multiply all values in the first
column by the ratio:
Actual voltage
Motor rated voltage

2) Multiply all values in the second column by the ratio:
Actual voltage
Motor rated voltage
3) And multiply all values in the last column by the ratio:
Actual voltage
Motor rated voltage
23
IPS-E-EL-100(1)
Feb. 2012
TABLE 2 - GENERAL EFFECT OF VOLTAGE VARIATIONS ON INDUCTION MOTOR

CHARACTERISTICS
Characteristic
Voltage Variation
Function of Voltage
90 Percent Voltage
110 Percent Voltage
Starting and maximum running torque
(Voltage)
Decreases 19%
Increase 21%
Synchronous speed
Constant
No Change
No Change
Percent Slip
1/(Voltage)
Increase 20%
Decrease 17%
Full-Load Speed
(Synchronous Speed-Slip)
Decrease 1
Increase 1%
Decrease 2%
Practically No Change
Increase 1-2%
Increase 1/2-1%
Practically No Change
Decrease 1-2%
Increase 1%
Increase 2-3%
Increase 4-5%
Decrease 3%
Decrease 4%
Increase 5-6%
Efficiency
Full Load
3/4 Load
1/2 Load
---
Power Factor
Full Load
3/4 Load
1/2 Load
---
Full-Load Current
---
Increase 11%
Decrease 7%
Starting Current
---
Decrease 10-12%
Increase 10-12%
Temperature Rise Full Load
---
Increase 6-7C
Decrease 1-2C
Maximum Overload Capacity
Voltage
Decrease 19%
Increase 21%
Decrease Slightly
Increase Slightly
Magnetic Noise-No load in particular
(Voltage)
* Note:
This data applies to motors above 25 horsepower (hp) .
6.1.6 power distribution systems
6.1.6.1 General
6.1.6.1.1 The distribution network shall be designed to carry continuously at least 120% of the After
Diversity Maximum Demand (ADMD) associated with peak design production at the maximum
ambient conditions.
6.1.6.1.2 The selected distribution arrangement shall have a degree of reliability consistent with the
type of load being supplied, and with the power supply design philosophy which provides for
coincidental maintenance and unscheduled outage of the largest component of on site generating
plant or unscheduled outage of the largest feeder component of the power supply equipment.
6.1.6.2 Radial systems

These systems distribute power radially from the power source to the load and shall be used in
single, duplicate or triplicate arrangements.
6.1.6.3 Single radial
6.1.6.3.1 The single radial system provide power to non-essential electrical loads or loads where
alternative sources of energy are available such as standby generating plant.
6.1.6.3.2 Each component of the single radial circuit shall be capable to supply 120% of the
required electrical load. Transformers or other plant which includes forced cooling equipment shall
not relay on the forced cooling arrangements to obtain the necessary rating.
24
Feb. 2012
IPS-E-EL-100(1)
6.1.6.4 Double radial
6.1.6.4.1 Critical and essential loads shall be supplied by two or more identically rated radial
system.
6.1.6.4.2 In double radial systems, each circuit shall be capable of carrying 120% of the ADMD and
all busbars shall include bus-section switchgear. They shall be arranged to ensure that unscheduled
outage of any component of the circuit would not result in loss of power supply after the faulty
equipment has been disconnected from the system, the only exception to this is the bus-section
switch.
6.1.6.4.3 Double radially fed systems shall generally be operated in parallel with all bus-section
switches closed. Also provision shall be considered for operation in two out of three scheme
system.( non-parallel incomers)
6.1.6.4.4 Where switchgear fault levels are found to be above the values outlined in 6.1.8.3.2
attention shall be given to operating with bus-section breakers open as opposed to purchasing
higher fault level switchgear. Where an open bus-section breaker philosophy is being given
attention, the need to restore rapidly the supplies to drives shall determine whether automatic
closure of bus section circuit breaker(s) is to be employed. Schemes with auto-reclosure are
covered in 6.1.6.7.
6.1.6.5 Triple radial
6.1.6.5.1 Critical and essential loads may be alternatively supplied by triple identically rated radial
systems. These systems are preferred to double radial systems wherever there is an overall total
cost advantage.
6.1.6.5.2 Each circuit of triple fed radial systems shall be capable of providing 60% of the ADMD
and all busbars shall be split into at least three sections with two bus-section switches. This will
allow for the loss of any one of the three circuits, leaving the two healthy circuits still capable of
providing 120% of the ADMD.
6.1.6.5.3 Triple radial systems shall be provided where the power flow is relatively large. They shall
generally be operated with only two circuits in parallel to reduce switchgear fault levels. The
incoming circuit breaker on the third identically rated feeder shall be left open and automatically
closed in order to restore rapidly full supplies to the load. Triple radial system can also be operated
with two non-parallel circuits closed and one open circuit for reserve.
Note:
For typical electrical distribution network see following typical single line diagrams1,2 and 3.
6.1.6.6 Ring fed systems
6.1.6.6.1 Power may be distributed from a primary or central substation to number of subsidiary
load centers by using two primary cable feeders connected in a ring emerging from the source
busbar and controlled by circuit breakers.
6.1.6.6.2 Ring fed systems should normally duplicate only the primary cables to the load substation.
They may however, duplicate the load substation transformers and the low voltage busbar by
providing a low-voltage or secondary bus section breaker.
6.1.6.6.3 Ring fed systems may be operated with the ring closed or with it open at some point.
6.1.6.6.4 Where the ring feed is operated closed, intermediate primary circuit breakers, including
unit feeder protection, shall be provided at all vital or essential load centers on the ring, thereby
ensuring fault clearance of only the unhealthy section of the ring. The whole of the ring circuit shall
25
Feb. 2012
IPS-E-EL-100(1)
be fully rated to be capable of supplying 120% of the ADMD at all substations. Essential or critical
loads may be supplied by ring systems if they are operated closed, their choice shall be based on
the comparative reliability and cost as compared to the duplicate radial systems.
6.1.6.6.5 Ring fed systems which are operated open shall not include circuit breakers on the ring.
Fault clearance shall be achieved at the source substation and in that event power will be lost to all
loads fed between the source and the open point on the ring.
In order that a fully section of the primary ring may be disconnected and repaired without power loss
during the whole of the repair period, the ring shall include isolating means at every load substation.
These ring dependent on availability, cost, and the need for rapid reconnection of load.
Open operated ring fed systems shall be permitted only to supply non-industrial system. Their
choice shall be based on the comparative reliability and cost as compared with single radially fed
systems with a non-automatic standby power supply back-up.
6.1.6.7 Automatic transfer schemes
6.1.6.7.1 Automatic transfer schemes shall be given attention where there is a need to obtain a
reliability level consistent with two or more sources of supply. Their use shall be economically
justified when compared against other ways of providing duplication of power sources, and shall be
limited to installations where there is a need to reduce switchgear short circuit levels either for
reasons of cost or non-availability. All schemes shall only include load transfers that never parallel
the preferred and emergency sources. Load transfer schemes may use circuit breakers, or on-load
transfer switches/contactors.
6.1.6.7.2 Load transfer schemes may be applied to either static loads or induction motor loads or
combination of the two. They shall not be used where synchronous motor loads are supplied. The
load transfer shall be arranged so that the residual voltage of induction motors has decayed to less
than 25% of the rated source voltage before the transfer is initiated. The rate of residual voltage
decay shall be calculated and the complete transfer scheme shall be subject to approval by the
client.
6.1.6.7.3 Induction motors which are controlled by circuit breakers, or contactors of the DC
controlled or AC controlled mechanically latched type shall include time delay under voltage
relaying. This relaying shall be set to trip the controller in typically 2 seconds or more on voltage
dips to below 85% of the rated voltage. Transfer schemes associated with switchgear supplying
these types of induction motor controllers shall be designed either to be capable of reaccelerating
the motors within if the transfer taken place within the motor under voltage tripping time, or time
delaying the transfer to be in excess of the motor under voltage tripping time.
6.1.6.7.4 Motors which are controlled by unlatched AC, contactors will inherently disconnect from
the supply on loss of voltage. Where it is required to restore power to these types of motor drives
the auto-transfer schemes shall be supplemented by contactors control schemes which restart
motors individually or in groups after a requisite time delay.
6.1.6.7.5 Load transfer schemes for the startup, run and loading of a standby generator on to a
busbar normally fed from a preferred AC source shall be initiated by time delayed under voltage
relaying set at 85% volts which shall trip the AC source and auto-start up the standby generator
simultaneously. No transfer time delay is required in this case as standby generators take many
seconds to be run up and loaded.
6.1.6.7.6 Power system re-acceleration and re-start studies to determine the most technically
acceptable and cost effective solution shall be carried out for each load transfer scheme considered
and all such studies and their conclusions shall be subject to approval by the client.
6.1.6.8 Manual transfer schemes

Interlock should be provided for 2 out of 3 systems, such that in every distribution only 2 breakers of
3 could be in close position.
26
Feb. 2012
27
IPS-E-EL-100(1)
Feb. 2012
28
IPS-E-EL-100(1)
Feb. 2012
29
IPS-E-EL-100(1)
Feb. 2012
IPS-E-EL-100(1)
6.1.7 Power factor improving equipment
6.1.7.1 Power factor improving equipment shall be provided on all installation where energy is
imported from a public utility which applies a tariff penalty associated with low power factor energy
provision.
6.1.7.2 The equipment may be capacitors or synchronous motors depending on economics and
suitability over the range of known operating condition.
6.1.7.3 Where the public utility system is normally in parallel with on site generation, the generating
equipment shall be designed and operated to supply the load KVAR; this will avoid the need for
power factor improving equipment to be installed for the normal parallel operating mode and will
limit its provision to that required for standby (unparalleled operation alone).
6.1.7.4 The amount of power factor equipment provided shall be such as to avoid any possibility of
paying power factor penalties under the worst conceivable plant operating condition.
6.1.7.5 Any power factor improving equipment provided either to reduce system losses (or to raise
voltage levels alone) shall be subject to approval of client.
6.1.7.6 Where synchronous motors are supplied for power factor improvement, they shall include
constant power factor control equipment.
Note:
In order to avoid risks of over voltages or high transient torques, induction motors shall not
be switched as a unit with their power factor improving capacitors, unless the capacitive
current is less than the no load magnetizing current of the associated induction motor.
6.1.7.7 Correction can be applied in the form of individual, group or central compensation to set the
power factor at 0.95. A technical / economical study for the size and location of power factor
correction equipment shall be performed.
6.1.8 Power system fault considerations
6.1.8.1 Fault calculations
6.1.8.1.1 The fault currents that flow as a result of short circuits shall be calculated at each system
voltage for both three phase and phase to earth fault conditions. These calculated currents shall be
used to select suitably rated switchgear and to allow the selection and setting of protective device to
ensure that successful discriminatory fault clearance is achieved.
6.1.8.1.2 The voltage disturbance sustained during the faults and after fault clearance shall also be
ascertained to ensure that transient disturbances do not result in loss of supplies due to low
voltages or overstressing of plant insulation due to high voltages.
6.1.8.1.3 The calculation of fault currents shall include the fault current contribution from generators
and from synchronous and induction motors. Both the AC symmetrical and DC component of fault
currents shall be calculated at all system voltages. Public utility fault in feeds shall be obtained from
the public utility concerned, and they shall exclude any decrement associated with fault duration,
though maximum and minimum values consistent with annual load cycles shall be obtained.
6.1.8.1.4 Positive sequence impedances shall be used for calculating balanced three phase faults.
Positive, negative and zero sequence impedances shall be used for calculating unbalanced faults.
6.1.8.1.5 Three phase balanced fault current calculations shall be carried out to obtain prospective
circuit breaker ratings and shall include:
30
Feb. 2012
IPS-E-EL-100(1)
i) Asymmetric make capacity-expressed in peak amperes and calculated half a cycle after fault
inception. Both AC and DC current decrements shall be included for the half cycle.
ii) Asymmetric break capability-expressed in rms amperes calculated at a time at which the breaker
contacts are expected to part and allowing a maximum of 10 ms for instantaneous type protection
operation. Both AC and DC decrements shall be included for the selected time.
iii) Symmetrical break capability-expressed in rms amperes calculated at a time as defined in item
(ii) above. This assumes nil DC current component and shall allow for AC decrement for the
selected time.
6.1.8.1.6 Earth fault currents may be assumed to be no greater than the maximum phase fault
currents for solidly earthed systems. On systems where the earth fault currents are limited by
neutral earthing equipment, the currents may be assumed to include no decrement and shall be
considered constant whatever the level of bonding between the conductor and the faulted phase.
6.1.8.1.7 Both the AC and DC components of motor fault current contributions shall be calculated
and included in calculation of prospective fault currents. At the instant of fault inspection the AC
peak symmetrical component and the DC component shall be taken to be identical. Both values
shall be taken as the peak direct-on-line starting current, this being dictated by the motor locked
rotor reactance. Both these currents shall be taken to decay exponentially with time using AC and
DC short circuit time constants respectively. The AC time constant shall be determined by using the
ratio of the locked rotor reactance to the standstill rotor resistance. The DC time constant shall be
determined by using the locked rotor reactance to the stator resistance ratio. In the case of faults
not directly on the motor terminals, these time constants shall be modified to take account of
external impedances to the point of fault.
6.1.8.1.8 The calculation of individual fault current contributions shall be carried out for individual
motors of significant rating on the power system. Generally motors with ratings greater than 500 kw
should be treated in this way.
6.1.8.2 Equipment fault current ratings
6.1.8.2.1 All switchgear and distribution equipment on the power system shall be capable of
carrying the prospective symmetrical fault currents for specified short time duration of 1 or 3
seconds without deleterious effect. The choice between 1 and 3 second durations shall be dictated
by availability, economics and fault current protection clearing times. Generally 3 second short time
rating is preferred to avoid the necessity for rapid protection. The back-up fault current protection
clearing times shall always be less than the equipment short time current rating.
6.1.8.2.2 The closure of switchgear on to a balanced or unbalanced fault shall not result in shock
load damage to healthy parts of the system as a result of peak asymmetrical make currents
following.
6.1.8.2.3 The selection of circuit breakers shall be dependent on the make and break duty which the
breaker is required to cater for switching devices that may be closed on to fault shall have the
necessary fault making capability.
6.1.8.2.4 Plant protected by fault current limiting HRC type fuses need not be designed to sustain
the prospective shock or thermal loads obtained by calculating system fault currents.
6.1.8.3 Methods of limiting fault currents
6.1.8.3.1 The power distribution system shall be designed to provide the required security and
quality of supply with prospective fault levels within the capability of commonly available switchgear
acceptable maximum short circuit symmetrical breaking current for various system voltages unless
otherwise specified or approved by company are as follows:
31
Feb. 2012
IPS-E-EL-100(1)
i) Power systems with a voltage in excess of 1000 V shall be so designed that the rms value of the
AC components of the short-circuit breaking current of the circuit breakers is to IEC 60056 and or
shall not exceed 25 KA.
ii) For power systems with a voltage less than 1000 volt, the rms value of the AC component of the
short circuit breaking current of circuit breaker designed shall be IEC 60157 and shall not exceed 50
KA.
If the power system design indicates prospective short circuit requirements exceeding the maximum
circuit breaker rating given above, the following alternatives should be considered:
i) Increase the system reactance, provided this causes no other technical or commercial problem.
ii) Change the operating mode by operating with certain breakers open and provide auto-transfer
facilities to reinstate the supply security and quality levels.
iii) Purchase switchgear and equipment to provide for the higher short circuit levels if these are
available.
iv) Provide fault current limiting devices other than fuses.
v) Carry out any combination of the alternatives listed in items (i) to (iv) above.
6.1.8.3.2 To have an idea of the short time withstand current for switchgear the following are to be
considered:
a) All short circuit studies to be carried out in compliance with requirements of IEC standards.
b) The minimum short time withstand current for busbars shall be according to figures given in
Table 3.
c) The minimum short time withstand current for low voltage busbars with explosion protection type
Exd (EExd) shall be 15 KA.
TABLE 3
RATED VOLTAGE
WITHSTAND CURRENT
20 KA (R.M.S.)
25 KA (R.M.S.)
25 KA (R.M.S.)
25 KA (R.M.S.)
25 KA (R.M.S.)
25 KA (R.M.S.)
50 KA (R.M.S.)
63-66 KV
33 KV
20 KV
* 11 KV
6 KV
* 3.3 KV
0.4 KV
* Refer to: 6.1.5.1
6.1.8.4 Effects of faults on distribution systems

Bolted three phase faults on the system will depress the voltage at the point of fault and
downstream of the fault to zero.
All locations between the sources of fault current and the fault will experience reduced voltages.
This conditions will apply until the faulty section has been cleared at which stage voltages will be
rapidly restored.
The following effects of three phase fault applications and clearances shall be investigated:
i) Possible loss of synchronize between parallel running synchronous machines. This would only be
likely for dissimilar machines or for identical machines connected to the fault which are not
electrically symmetrical.
ii) The possibility of motor contactors dropping out, and the consequential need to re-start the
motors, either manually or automatically.
iii) Possible extinction of certain discharge lamps and the time for re-ignition. The provision of
emergency lighting systems avoids the need to study this.
32
Feb. 2012
IPS-E-EL-100(1)
iv) Loss of electronic and control equipment supplies resulting in maloperation. The provision of DC
or no break supplies for vital loads avoids the need to study this.
v) The extent of overvoltage on the system components resulting from fault clearance. This could
cause unacceptable transient recovery voltages occurring for short periods which may have a
destructive effect on electrical insulation.
6.1.9 System one line diagram

A one line diagram is one which indicates by means of single lines and simplified symbols the
course and component devices or parts of an electric circuit or system of circuits.
In the preparation of preliminary plans for a system or specification it is not necessary to show all
details in complete form on a one line diagram. Some of the more important items to be included
are as follows:
i) Voltage, phase and frequency.
ii) The available fault level of system and (time).
iii) The size, type and number of incoming and outgoing cables.
iv) The ratings, impedances and connections of the transformers.
v) The points at which power is metered (where applicable).
vi) The amount and character of the load on all feeders.
The following items if given special attention during preparation ensure complete, accurate and
clear diagrams.
a) Keep the diagram simple
b) Avoid duplication
c) Use of standard symbols
d) Show all known facts
By the following list before releasing a diagram the omission of some of the more important details
can be avoided:
- Rating and protection of devices.
- Ratio of current and potential transformers.
- Connection of transformer winding.
- Circuit breaker rating.
- Switch and fuse rating.
- Function of relays.
- Rating of motors and transformers.
- Size and type of transformers.
- Size and type of cables.
A statement should accompany this information stating whether or not the neutral of any apparatus
connected to the source is grounded. If grounded the statement should specify whether the ground
is solid or through an impedances, if the latter, the value of the impedances should be given.
e) Show future plans and extension where applicable.
f) Include correct title data.
33
Feb. 2012
IPS-E-EL-100(1)
6.1.10 Device function numbers

While preparing single line diagrams, It is necessary to show the numbers indicating electrical
instrument function.
The most common type of electrical/instrument function numbers which follow are extracted from:
IEEE Std. C 37.2 "Standard Electric Power System Device Function Numbers"
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Master element
Time-Delay starting or closing relay
Checking or interlocking relay
Master contactor
Stopping device
Starting circuit breaker
Reserved for future application
Control power disconnecting device
Reversing device
Unit sequence switch
Multifunction device
Over speed device
Synchronous-Speed device
Under speed device
Speed or frequency matching device
Reserved for future application
Shunting or discharge switch
Accelerating or decelerating device
Starting-To-Running transition contactor
Electrically operated valve
Distance relay
Equalizer circuit breaker
Temperature control device
Volts per hertz relay
Synchronizing or synchronism check device
Apparatus thermal device
Under voltage relay
Flame detector
Isolating contactor
Annunciator relay
Separate excitation device
Directional power relay
Position switch
Master sequence device
Brush-Operating or slip-ring Short-Circuiting device
Polarity or polarizing voltage device
Undercurrent or under power relay
Bearing protective device
Mechanical condition monitor
Field relay
Field circuit breaker
Running circuit breaker
Manual transfer or selector device
Unit sequence starting relay
Atmospheric condition monitor
Reverse-Phase or phase-balance current Relay
Phase-Sequence or phase balance voltage Relay
Incomplete sequence relay
Machine or transformer thermal relay
Instantaneous over current or rate-of rise Relay
34
Feb. 2012
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
IPS-E-EL-100(1)
AC time over current relay

AC circuit breaker
Exciter or DC generator relay
Turning gear engaging device
Power factor relay
Field application relay
Short-Circuiting or grounding device
Rectification failure relay
Overvoltage relay
Voltage or current balance relay
Density switch or sensor
Time-Delay stopping or opening relay
Pressure switch
Ground detector relay
Governor
Notching or jogging device
AC directional over current relay
Blocking relay
Permissive control device
Rheostat
Level switch
DC circuit breaker
Load-Resistor contactor
Alarm relay
Position changing mechanism
DC over current relay
Telemetering device
Phase-Angle measuring or out-of-step Protective relay
AC reclosing relay
Flow switch
Frequency relay
DC reclosing relay
Automatic selective control or transfer Relay
Operating mechanism
Carrier or pilot-wire receiver relay
Lockout relay
Differential protective relay
Auxiliary motor or motor generator
Line switch (disconnecting switch)
Regulating device
Voltage directional relay
Voltage and power directional relay
Field-Changing contactor
Tripping or trip-free relay
Used only for specific application
6.1.11 Drawings and schedules

Unless specified otherwise, the consultant responsible for the system design shall provide the
following:
1) Plant layout diagram
2) Hazardous area classification (where applicable)
35
Feb. 2012
IPS-E-EL-100(1)
3) General single line diagram

4) Single line diagram for each substation
5) Relaying and metering diagrams
6) Schematic and wiring diagram
7) Coordination diagrams
8) Substation layouts
9) Cable runs and schedules (type, size and length)
10) Lighting layout
11) Earthen layout
12) Load flow analysis
13) Short circuit studies
14) Stability studies
15) Load shedding system
6.1.12 Alarms, indication and communication system
6.1.12.1 Plant alarms
6.1.12.1.1 Each substation and each on-site generator shall be provided with an alarm annunciation
system. This shall comprise an alarm panel which shall collect together all the alarm conditions
associated with that particular substation or generator. A common alarm shall be derived from each
substation or generator alarm panel for transmission to an emergency control center.
6.1.12.1.2 Each generator alarm panel shall have an alarm window associated with each separate
alarm condition required.
6.1.12.1.3 A window shall be provided on the substation alarm panel for each switchboard circuit
breaker way which has protective relaying.
Where battery chargers are provided for closing and tripping supplies a window shall be provided
on the substation alarm panel for each battery charger.
6.1.12.1.4 Each alarm window of a substation alarm panel shall be operated by the combined alarm
functions of the equipment the window is supposed to represent. For any circuit breaker each
protective relay shall provide a contact into a common alarm circuit which shall operate the
appropriate circuit breaker alarm window in the alarm panel. The alarms associated with a battery
charger shall form a common alarm to operate the appropriate battery charger alarm window in the
alarm panel.
6.1.12.2 Fire alarm

Fire alarm circuits should be installed in a manner that will guarantee the least interruption from
faults and changes in buildings or plant operations. Lines should be arranged to provide easy
means of testing and of isolating portions of the system, in case of fault or changes without
interference with the balance of the system.
6.1.12.3 Indications
6.1.12.3.1 Local indication of status of circuit breakers on switchgear shall be as described on

IPS-M-EL-143(2) and IPS-M-EL-144(2).
36
Feb. 2012
IPS-E-EL-100(1)
6.1.12.4 Plant communication system

Any plan for the protection of a plant must include an adequate and reliable system of
communication, both within the plant and to the associated utilities and emergency services which
may be called upon in case of need. This can be accomplished in several ways; a principal one is
by a completely self-contained and self-maintained inter-plant system of telephones, alarms, etc.,
and may include modern radio equipment as well.
6.1.13 Safety and plant protection
6.1.13.1 Personnel safety

There are listed below items which shall be considered in order to provide safe working conditions
for the personnel.
1) Interrupting devices shall be able to function safely and properly under the most severe duty to
which they may be exposed.
2) Protection shall be provided against accidental contact with energized conductors by elevation,
barriers, enclosures, and other similar equipment.
3) Disconnecting switches should not be operated while they are carrying currents, unless designed
to do so. Suitable barriers shall be provided between phases to confine accidental arcs unless
adequate space separation is provided.
4) In many instances interlocks between the disconnecting switch and the power circuit breaker are
desirable, so that the breaker in series shall be opened first before the disconnects can be
operated, thus preventing accidental opening of the disconnects under load.
5) Sufficient unobstructed room in any area containing electric apparatus shall be provided for the
operator to perform all necessary operations safely.
6) A sufficient number of exits with panic hardware on all doors shall be provided from any room
containing electric apparatus such as a substation, control room or motor so that escape from this
area can be easily affected in the event of failure of apparatus in the room.
7) A protective tagging procedure shall be set up to give positive protection to men working on
equipment. Such a procedure shall be coordinated with the local utility for the common equipment.
8) Industrial plant electric systems should generally be designed so that all necessary work on
circuits and equipment can be accomplished with the particular circuits and equipment deenergized.
9) All circuits shall be marked in the switching station so as to be readily identified. Cables shall be
identified with suitable tags at both ends and in all manholes for the protection of men working on
them.
10) A fire crew shall be formed of local employees who are familiar with the equipment and the
hazards involved. This group shall be trained in the proper procedures to follow in the event of fire
in the electric apparatus, the proper use of the various types of extinguishers and methods of fire
fighting.
For more details see IEEE Guide for Substation Fire Protection IEEE Std 979-1994.
6.1.13.2 Equipment safety

Electrical interlocks : Safety interlocks can be arranged for almost any machine and any operating
condition.
"An interlock is a device actuated by the operation of some other device with which it is directly
associated to govern succeeding operations of the same or allied devices."
Interlocks have three general functions:
37
Feb. 2012
IPS-E-EL-100(1)
To assure personal safety
To protect equipment
And to coordinate complex operations
Adequate machinery guarding is of course basic to any organized safety program.
Human habits and practices in the interest of safety are difficult to establish and maintain,
interlocking of equipment either by manufacturer or by the user removes hazards and is
part of safe design and installation. As a general rule the starting point in determining the
interlocking is to consider the past accident history of injury or major material damage, the
of whether the use of an interlocking device to prevent the injury should be considered.
however
a critical
need for
question
It should be remembered that interlocking devices and their application go beyond protecting the
point of operation during the normal work process. They can be used to restrict, access areas
through gate operated controls or through other device such as castle interlock.
Interlocks can initiate visual or audible warnings or stop an operation or malfunction. Key type
interlocks are often employed for access and sequence control.
If a visual warning is desirable flashing red light may be considered. Immediately, there is the
problem of "burned out" light and the system is not "fail safe". Two lights in parallel offer redundancy
and are generally acceptable.
In a series of process operations interlocks can be provided which will afford the necessary safety
for operator and equipment in the event of failure of sequence timers or controllers.
The design and application of interlocks usually affect a critical safety function. It follows that they
must be extensively tested and proved be convenient to use, have fail safe provisions and if
applicable have detailed procedures to verify proper function.
6.1.14 Hints on protection of property against fire

A potential fire or explosion hazard is inherent with the use of nearly all electric apparatus and
proper arrangement and protection of the equipment at the start will minimize if not eliminate
serious property damage or interruption to production when insulation failures or breakdown occur.
The fire and explosion hazard of oil-insulated and compound-filled equipment is one of the most
common hazards to safeguard against. Fires or explosions in oil insulated transformers occur
infrequently, but where they do the results may be disastrous depending upon the arrangement of
the equipment and the safeguards provided. The old practice of locating oil-filled transformers in the
same room with an important switchgear assembly or other valuable apparatus should be avoided
because a fire in the transformer will usually involve the other equipment increasing the damage
and prolonging the interruption to production.
The National Electrical Code clearly outlines the installation requirements for transformers of all
types. Oil-insulated transformers installed indoors must be installed in a vault of fire resistant
construction if the total capacity exceeds 75 KVA .
Where a vault is required, adequate ventilation and drainage facilities are necessary to prevent
overheating of the transformer and to drain away, to a safe place, any oil that may be released or
expelled.
The cost of a vault may be eliminated, and a saving in space effected, by substituting dry type
transformers in place of the oil insulated type. Dry-type sealed-tank nitrogen-filled transformers are
considered fire and explosion resistant and need no special safeguards from this standpoint.
Where oil-insulated transformers are installed outdoors they should be located at least 8 meters
away from combustible buildings or structures. They should not be located under important bridges,
conveyors, tanks or similar structures where heat from a fire in the transformer may cause collapse
of or serious damage to the structure. Facilities such as crushed stone-filled basins or drained
concrete basins should be provided under the transformers to drain away and oil that may be
expelled from them in time of trouble. Where a fire in one outdoor oil-insulated transformer is likely
to involve other transformers in the same bank, a non-combustible barrier or wall is sometimes
provided between adjacent transformers to confine the fire to the unit in which it started.
38
Feb. 2012
IPS-E-EL-100(1)
Permanently piped fire extinguishing Co 2 systems shall also be installed over large oil-insulated
transformers or other oil-insulated apparatus where the value or importance of the apparatus and
nearby equipment justifies this expense. These systems may be arranged to discharge either
manually or automatically. One system employs water spray nozzles connected to a reliable and
strong water supply.
The grouping together of a number of valuable or important cables or wires in trenches, cable
boxes, junction boxes and manholes should be avoided, particularly if they have combustible
insulation. This applies to low, medium, and high-voltage installations, and lead sheathed cables as
well. A failure in one cable or conductor can cause an arc that ignites the insulation on one cable
and fire may destroy the entire group, or the arc can do extensive damage in the event of sustained
arcing. Where it is necessary to group such cables together, they should be protected with a
fireproof covering.
The control circuits in power houses and substations should be arranged so that they will not be
exposed to damage by arcing or fire. When possible, these wires should have asbestos or similar
fire-resistive coverings.
An adequate supply of fire extinguishers should be provided on the premises, particularly in the
vicinity of large quantities of electric apparatus. Extinguishers suitable for use on live electric
apparatus are the vaporizing liquid, carbon dioxide, and dry chemical types.
Where insulating oil or compound is present in large quantities in power houses, substations, and
motor rooms where there are many large motors present.
Note:
For further information on fire protection see the following Standards:
IPS-E-SF-260 Automatic detectors and fire alarm system
IPS-G-SF-126 Hand and wheel type fire extinguishers
IPS-E-SF-160 Co 2 gas fire extinguishing system
6.1.15 Special studies
6.1.15.1 Load flow analysis

The objective of load flow analysis is to check voltage profile and circuit loading conditions under
steady state conditions. Systematic routine solution of load flow problems are outlined as follows:
1) Mesh current method and connection matrices.
2) Nodal voltage method and connection matrices.
3) Application of nodal voltage method to the solution of power system load flow problem.
4) Direct methods involving inversion of the nodal admittance matrix.
5) Modification of the inverse of the nodal admittance metric.
6) Iterative methods
7) Tearing
6.1.15.2 Short circuit studies

Refer to clause 12 under title power system fault consideration.
6.1.15.3 Stability study of system

A synchronous power system has steady state stability if after a small slow disturbance it can regain
and maintain synchronous speed; a small slow disturbance is taken to mean normal load
fluctuation, including the action of automatic voltage regulators and turbine governors. A power
39
Feb. 2012
IPS-E-EL-100(1)
system has transient stability if, after a large sudden disturbance it can regain and maintain
synchronous speed: a large sudden disturbance is one caused by faults and switching. In order to
develop the main principles simply it is assumed that the automatic voltage regulations and turbine
governors are too slow to act during the period of the analysis. Dynamic stability refers to the case
of transient stability where the regulations and governors are fast acting and are taken into account
in the analysis.
The stability limit of the system is the maximum (Steady state) power which can be transformed
through the system without loss of stability. The limits depend also on the magnitude, type and
location of the disturbance. The stability factor is the ratio of the stability limit to the actual loadpower transfer it can be shown that all the machines in a power exporting area can be reduced to
an equivalent generator "G" and similarly that all the machines in a power importing area can be
reduced to an equivalent synchronous motor M the distribution or transmission system which
connects these two areas is called interconnection (or tie line) the above two machine system can
be reduced to one machine connected to an infinite busbar a constant voltage and constant
frequency system.
Generally resistance will be neglected, relative to the inductive reactance of the system.
To analyze the transient and dynamic performance of power systems, after large load changes and
fault disturbances. These should be used to check:
a) The ability of the system to stay in synchronism.
b) Induction motor stability after start.
c) Re-acceleration and re-start schemes.
d) The need and effectiveness of under frequency load shedding schemes.
They should also be used to consider the technical merit of:
e) Auto changeover schemes.
f) Parallel or open operation or radial feeders.
g) Operation of fault limiting devices.
h) Insertion of switched reactors or capacitors, etc.
6.2 Non-industrial electrical systems
6.2.1 General
This recommendation covers the basic requirements to be considered in design of electrical
systems in non-industrial buildings that comprise all buildings outside the process area, e.g.
workshops, warehouses, canteens, administration and residential buildings, fire stations, training
centers, gatehouses, chemical stores, etc.
6.2.2 Planning guide for distribution design

The following procedure is given to guide the engineer in the design of an electric system for any
non-industrial buildings.
6.2.2.1 Obtain a general layout and mark it with the major loads at various locations and determine
the approximate total non-industrial buildings load in horsepower, kilowatts, and kilo volt-amperes.
Estimate the lighting, air-conditioning, and other loads from known data.
6.2.2.2 Determine the total connected load and calculate the maximum demand by using demand
and diversity factors.
6.2.2.3 Investigate unusual loads, such as the starting of large motors, or welding machines, and
operating conditions such as boiler auxiliary motors, loads that must be kept in operation under all
conditions, and loads that have a special duty cycle.
40
Feb. 2012
IPS-E-EL-100(1)
6.2.2.4 Investigate the various types of distribution system and select the system or systems best
suited to the requirements of the switchboard. Make a preliminary one line diagram of the power
system.
6.2.2.5 If power is to be purchased from the utility, obtain such information concerning the supply
system or systems as:
performance data, voltage available, voltage spread, type of systems available, method of system
neutral grounding, and other data such as relaying, metering and the physical requirements of the
equipment. The interrupting rating and momentary ratings of power circuit breakers should be
obtained as well as the present and future short-circuit capabilities of the utility system at the point
of service to the switchboard. Investigate the utilitys power contract to determine if off-peak power
at lower rates available, and any other requirements, such as power factor and demand clauses,
that can influence power cost.
6.2.2.6 A cost analysis may be required of the different voltage levels and various arrangements of
equipment to justify and properly determine the voltage and equipment selected. The study should
be made on the basis of installed cost including all the components in that section of the system.
6.2.2.7 Check the calculations of short-circuit requirements to be sure that all breakers are of the
correct rating. Review the selectivity of various protective devices to assure selectivity during load
or fault disturbances.
6.2.2.8 Calculate the voltage spread and voltage drop at various critical points.
6.2.2.9 Determine the requirements of the various components of the electric distribution system
with special attention given to special operating and equipment conditions.
6.2.2.10 Review all applicable national and local Codes for requirements and restrictions.
6.2.2.11 Check to see that the maximum safety features are incorporated in all parts of the system.
6.2.2.12 Write specification on the equipment and include a one-line diagram as a part of the
specifications.
6.2.2.13 Obtain typical dimensions of equipment and make drawings of the entire system.
6.2.2.14 Determine if the existing equipment is adequate to meet additional load requirements.
Check such ratings as voltage, interrupting capacity, and current-carrying capacity.
6.2.2.15 Determine the best method of connecting the new part of the power system with the
existing system so as to have a minimum outage at minimum cost.
Naturally the above procedure will not automatically design the electric power system in itself; it
must be used with good, sound, basic engineering judgement.
6.2.2.16 Estimate the future load, it is necessary to study building plans and area utilization plans of
the relevant area.
6.2.2.17 A general layout of the buildings should be available before the engineer can begin his
study. This layout usually gives the location and the size of the proposed building or buildings in the
initial particular project. The extent of the available layout gives the engineer an idea of the possible
expansion in the future, and must be considered by the engineer in planning the electric distribution
system.
6.2 2.18 The voltage regulation of system shall not exceed 5%.
6.2.3 Selection of distribution voltage

In general the voltage levels of the low-voltage and medium-voltage systems are fixed for the utility
supply authorities.
For the low-voltage system of the public supply, a uniform standard value of 230/400 Volt is
recommended. Where a high proportion of load is in motors then in new installations 400 volt 3
phase is also employed.
The medium-voltage systems lying above the low-voltage systems must fulfill two main functions: It
must be sufficiently powerful to transmit the high incoming power from the main substation (feeding
41
Feb. 2012
IPS-E-EL-100(1)
from the high-voltage systems) and its component parts on the other hand transmit energy
economically to numerous main substations and consumer stations. The optimum values for high
voltage systems are the voltage levels of 11 and 20 kV or 33 kV.
6.2.4 Power distribution systems
6.2.4.1 General
a) In locations where there is a significant rising demand for power the selection of voltage levels in
the medium-voltage systems forms a particularly important part of the network planning. Frequently
because of the hitherto development, numerous voltage steps are found and because of several
transformation steps additional costs for investment and losses are incurred. It must, however, be
checked whether these voltage levels are adequate in the future for increasing demand or whether
a higher voltage system should be used. In this aspect it must be assessed whether an existing
intermediate voltage can be omitted partially or even completely or should be revised.
b) The distribution network shall be designed to carry continuously at least 120% of the After
Diversity Maximum Demand (ADMD) associated with peak design production at the maximum
ambient conditions.
c) The selected distribution arrangement shall have a degree of reliability consistent with the type of
load being supplied, and with the power supply design philosophy which provides for coincidental
maintenance and unscheduled outage of the largest component of on site generating plant or
unscheduled outage of the largest feeder component of the power supply equipment.
6.2.4.2 Distribution arrangements

The distribution system shall be designed using one of the following arrangements:
6.2.4.2.1 Single radial

a) The single radial system provide power to non-essential electrical loads or loads where
alternative sources of energy are available such as standby generating plant.
b) Each component of the single radial circuit shall be capable to supply 120% of the required
electrical load. Transformers or other plant which includes forced cooling equipment shall not relay
on the forced cooling arrangements to obtain the necessary rating.
6.2.4.2.2 Double radial

a) Critical and essential loads should be supplied by two or more identically rated radial system.
b) In double radial systems, each circuit shall be capable of carrying a 120% of the ADMD and all
busbars shall include bus-section switchgear. They shall be arranged to ensure that unscheduled
outage of any component of the circuit would not result in loss of power supply after the faulty
equipment has been disconnected from the system; the only exception to this is the bus-section
switch.
c) Double radially fed systems shall generally be operated in parallel with all bus-section switches
closed.
d) Where switchgear fault levels are found to be above the values outlined in 6.1.8.3.2 attention
shall be given to operating with bus-section breakers open as opposed to purchasing higher fault
level switchgear. Where an open bus-section breaker philosophy is being given attention, the need
to restore rapidly the supplies to drives shall determine whether automatic closure of bus section
circuit breakers(s) is to be employed. Schemes with auto-reclosure are covered in 6.1.6.7.
42
Feb. 2012
IPS-E-EL-100(1)
6.2.4.2.3 Triple radial

a) Critical and essential loads may be alternatively supplied by triple identically rated radial systems.
These systems are preferred to double radial systems wherever there is an overall total cost
advantage.
b) Each circuit of triple fed radial systems shall be capable of providing 60% of the ADMD and all
busbars shall be split into at least three sections with two bus-section switches. This will allow for
the loss of any one of the three circuits, leaving the two healthy circuits still capable of providing
120% of the ADMD.
c) Triple radial systems shall be provided where the power flow is relatively large. They shall
generally be operated with only two circuits in parallel to reduce switchgear fault levels. The
incoming circuit breaker on the third identically rated feeder shall be left open and automatically
reclosed in order to restore rapidly full supplies to the load.
6.2.4.2.4 Ring fed systems

a) Power may be distributed from a primary or central substation to number of subsidiary load
centers by using two primary cable feeds connected in a ring emerging from the source busbar and
controlled by circuit breakers.
b) Ring fed systems should normally duplicate only the primary cables to the load substation. They
may however, duplicate the load substation transformers and the low voltage busbar by providing a
low-voltage or secondary bus section breaker.
c) Ring fed systems may be operated with the ring closed or with it open at some point.
d) Where the ring feed is operated closed, intermediate primary circuit breakers, including unit
feeder protection, shall be provided at all vital or essential load centers on the ring, thereby ensuring
fault clearance of only the unhealthy section of the ring. The whole of the ring circuit shall be fully
rated to be capable of supplying 120% of the ADMD at all substations. Essential or critical loads
may be supplied by ring systems if they are operated closed, their choice shall be based on the
comparative reliability and cost as compared to the duplicate radial systems.
e) Ring fed systems which are operated open shall not include circuit breakers on the ring. Fault
clearance shall be achieved at the source substation and in that event power will be lost to all loads
fed between the source and the open point on the ring.
In order that a fully section of the primary ring may be disconnected and repaired without power loss
during the whole of the repair period, the ring shall include isolating means at every load substation.
These ring dependent on availability, cost, and the need for rapid reconnection of load.
Open operated ring fed systems shall be permitted only to supply non-essential loads. Their choice
shall be based on the comparative reliability and cost as compared with single radially fed systems
with a non-automatic standby power supply back-up.
6.2.5 Power supply systems
6.2.5.1 General
For the estimation of loads for large building complexes the physical arrangement (vertical or
horizontal) of the individual consumers and the distribution of load center within the building must be
taken into consideration. Apart from consumer equipments spread across an area, e.g. light fittings
and small appliances, mostly also concentrated loads (lifts, air conditioning equipment, or large
kitchens) must be supplied.
6.2.5.2 Power requirement

To plan the incoming supply of the system under consideration from a higher level of voltage or
from a power station requires knowledge of the total load to be expected. The time related differing
43
IPS-E-EL-100(1)
Feb. 2012
load peaks of individual system parts are taken into account when determining the power
requirements. It is necessary to take care of Maximum Demand and Diversity.
6.2.5.3 Maximum demand
Maximum demand (often referred to as MD) is the largest current normally carried by circuits,
switches and protective devices; it does not include the levels of current flowing under overload or
short circuit conditions. Assessment of maximum demand is sometimes straightforward. For
example, the maximum demand of a 220 V single-phase 8 kW shower heater can be calculated by
dividing the power (8 kW) by the voltage (220 V) to give a current of 36.3 A. This calculation
assumes a power factor of unity, which is a reasonable assumption for such a purely resistive load.
There are times, however, when assessment of maximum demand is less obvious. For example, if
a ring circuit feeds fifteen 13 A sockets, the maximum demand clearly should not be15 x 13 = 195
A, if only because the circuit protection will not be rated at more than 32 A. Some 13 A sockets may
feed table lamps with 60 W lamps fitted, whilst others may feed 3 kW washing machines; others
again may not be loaded at all. Guidance is given in Table 4.
Lighting circuits pose a special problem when determining MD. Each lamp-holder must be assumed
to carry the current required by the connected load, subject to a minimum loading of 100 W per
lamp holder (a demand of 0.45 A per lamp holder at 220 V). Discharge lamps are particularly
difficult to assess, and current cannot be calculated simply by dividing lamp power by supply
voltage. The reasons for this are:
1) control gear losses result in additional current,
2) the power factor is usually less than unity so current is greater,
3) chokes and other control gear usually distort the waveform of the current so that it contains
harmonics which are additional to the fundamental supply current.
TABLE 4 - CURRENT DEMAND OF OUTLETS
Type of outlet
Assumed current demand
2 A socket outlet
Other socket outlets
At least 0.5A
Rated current
Connected load, with minimum of 100
W
Lighting point
Shaver outlet, bell transformer or any
equipment of 5 W or less
May be neglected
Household cooker
10A + 30% of remainder + 5A for

socket in cooker unit
Switches for circuits feeding discharge lamps shall be rated at twice the current they are required to
carry, unless they have been specially constructed to withstand the severe arcing resulting from the
switching of such inductive and capacitive loads.
When assessing maximum demand, account must be taken of the possible growth in demand
during the life of the installation. Apart from indicating that maximum demand must be assessed,
the Regulations themselves give little help. Suggestions for the assumed current demand of various
types of outlet are shown in Table 4.
6.2.5.4 Diversity factor

A domestic ring circuit typically feeds a large number of 13 A sockets hut is usually protected by a
fuse or circuit breaker rated at 30 A or 32 A. This means that if sockets were feeding 13 A loads,
more than two of them in use at the same time would overload the circuit and it would be
disconnected by its protective device.
In practice, the chances of all domestic ring sockets feeding loads taking 13 A are small. Whilst
there maybe a 3 kW washing machine in the kitchen, a 3 kW heater in the living room and another
in the bedroom, the chance of all three being in use at the same time is remote. If they are all
connected at the same time, this could be seen as a failure of the designer when assessing the
44
Feb. 2012
IPS-E-EL-100(1)
installation requirements; the installation should have two ring circuits to feed the parts of the house
in question.
Most sockets, then, will feed smaller loads such as table lamps, vacuum cleaner, television or audio
machines and so on. The chances of all the sockets being used simultaneously is remote in the
extreme provided that the number of sockets (and ring circuits) installed is large enough. The
condition that only a few sockets will be in use at the same time, and that the loads they feed will be
small is called diversity.
By making allowance for reasonable diversity, the number of circuits and their rating can be
reduced, with a consequent financial saving, but without reducing the effectiveness of the
installation. However, if diversity is over-estimated, the normal current demands will exceed the
ratings of the protective devices, which will disconnect the circuits - not a welcome prospect for the
user of the installation! Overheating may also result from overloading which exceeds the rating of
the protective device, but does not reach its operating current in a reasonably short time. The
Regulations require that circuit design should prevent the occurrence of small overloads of long
duration.
The sensible application of diversity to the design of an installation calls for experience and a
detailed knowledge of the intended use of the installation. Future possible increase in load should
also be taken into account. Diversity relies on a number of factors which can only be properly
assessed in the light of detailed knowledge of the type of installation.
6.2.5.5 Applied diversity
Suggestions of values for the allowances for diversity are given in Table 5.
TABLE 5 - ALLOWANCE FOR DIVERSITY
Note the following abbreviations :
X is the full load current of the largest appliance or circuit
Y is the full load current of the second largest appliance or circuit
Z is the full load current of the remaining appliances or circuits
Type of final circuit
Lighting
* window-type cooler
or air conditioner
Heating and power
Cookers
Motors (but not lifts)
Instantaneous water
heaters
* Thermostatic water
heaters
Standard circuits
Sockets and stationary
equip.
Type of premises
Households
66% total demand
100%
Small shops, stores, offices

90% total demand
100%
Hotels, guest houses

75% total demand
100%
100% up to 10 A + 50%
balance
10 A + 30% balance + 5 A for
socket
100%X + 75%(Y+Z)
100%X + 80%Y + 60%Z
100%X + 80%Y + 60%Z
100%X + 80%Y + 60%Z
100%X + 100%Y + 25%Z
100%X + 80%Y + 60%Z

100%X + 100%Y + 25%Z
100%X + 50%(Y+Z)
100%X + 100%Y + 25%Z
100%
100%
100%
100%X + 40%(Y+Z)
100%X + 40%(Y+Z)
100%X + 50%(Y+Z)
100%X + 75%(Y+Z)
100%X + 50%(Y+Z)
100%X + 75%Y + 40%Z
* Note: Depending on the ambient temperature the allowance for diversity can be considered
by designer.
6.2.6 Power supply in non- residential buildings
6.2.6.1 Supply and distribution considerations
In this section consideration is given to some of the special features and requirements of the
installations in stores, office and leisure premises and other non domestic medium sized
installations.
45
Feb. 2012
IPS-E-EL-100(1)
While single phase 25 A services are adequate for the smaller shop or office unit, premises with a
prospective maximum demand in excess of about 5 kW will be provided with a three phase 230/400
volt supply.
The service cable will be terminated in a cut-out located in agreement with the Electricity Authority
where applicable. This should preferably be in a separate room away from stored materials, work
areas etc., with adequate wall space for the meters, and the consumers switchgear, together with
access space for maintenance and alterations later. The switchboard will consist of a main fuseswitch or circuit breaker adequate in capacity for the installation, a busbar chamber and a number
of circuit switch-fuses or circuit breakers which will in turn supply distribution. It is usually more
economic to locate distribution boards as near as possible to the centers of the electrical load. Thus
a building on three floors would have a distribution board on each floor fed by sub-main cables from
the main switchboard.
Unless three-phase motors or other three-phase equipments are to be installed, the three phases of
the supply should be segregated within the building. The lighting and all power circuits in any one
area should be connected to the same phase so that the risk of 400 volt appearing between two
adjacent outlets or pieces of equipment is minimized. Where, for good practical reasons, this
separation cannot be achieved warning notices are required wherever two items of equipment
connected to different phases are simultaneously accessible.
6.2.6.2 Circuits for power-using equipment
The growth in the use of telecommunications equipment, office machinery and data transmission
equipment means that almost every desk and work station may need access to such facilities. The
trend away from small offices towards large flexible open-plan areas which can be replanned to suit
changing needs makes the provision of such facilities somewhat more difficult. However, the
installation of a network of floor trunking which, if laid in a 2 meter matrix, provides the flexibility the
user will require in the future without the risks which follow the use of long trailing flexes. Floor and
skirting trunking systems are available with two or three compartments so that circuits supplying
socket outlets, telephones and data processing equipment can be carried along the same route. A
wide variety of floor trunking systems are available which are adjustable to match the finished floor
level and carpet or other floor finishes can be applied to them to render them without being
obstructed.
General purpose power circuits in commercial premises will usually be wired on the ring circuit
principle, an adequate number of outlets within a 100 m area being connected to a 32 A fuse or
circuit breaker. However, this practice to connect sockets to a single ring should be exercised with
care. The installation designer must be satisfied that the prospective demand on that circuit will not
exceed the 32 A rating of the circuit protection.
RING CIRCUIT FEEDING SOCKET OUTLETS

Fig. 1
46
Feb. 2012
IPS-E-EL-100(1)
6.2.7 Power supply in residential buildings

6.2.7.1 General
The supply enters the buildings at the service entry point, and then passes through the house
service cut-out which contains the main fuse and meter. In new properties these may be situated in
special boxes on the exterior of the house, while in flats they may be communally sited for ease of
reading by the Electricity Company staff. The distribution of electricity to all circuits in a house is
controlled by a consumers unit (Fig. 2), incorporating a main switch to isolate the supply. Each
circuit inside the house is connected to its own terminal, with a fuse or preferably miniature circuit
breaker matched in rating to the circuit it protects.
Consideration should be given at the earliest stage to the prospective short circuit current at the
origin of the installation. This is, in practical terms, the current which would flow if a short circuit
occurred in the consumers main switch. The level and duration of this current is dependent upon
the electricity network and fuse characteristics. The designer needs to satisfy himself that the main
switch or consumers unit proposes to use will withstand the worst short circuit condition that could
be imposed upon it and must therefore relate the data provided by the power authority with the
manufacturers data.
In the event of a fault occurring in an installation, whether in an appliance or part of the wiring, it is
essential that the faulty section be disconnected from the supply immediately, although the
remainder of the system should remain in operation. This can be achieved by an adequate system
of fuses or miniature circuit breakers, and by the provision of earthing.
TYPICAL ARRANGEMENTS FOR FEEDING FINAL CIRCUITS IN A NON-INDUSTRIAL

BUILDING
Fig. 2
6.2.7.2 Circuits for domestic installations
In selecting consumers unit the designer should consider:
a) The adequacy of the main switch for the maximum demand of the installation.
b) The number of circuits required to be connected to it and their respective loadings.
c) The benefits of installation of miniature circuit breakers rather than fuses.
d) The added safety provided by one or more residual current devices.
e) The desirability of providing at least two spare way for future needs.
The designer shall decide on rating of main switches.
The decision regarding the number of circuits is to some extent subjective but the following
represents a typical selection:
a) Lighting circuit, ground floor.
47
Feb. 2012
IPS-E-EL-100(1)
b) Lighting circuit, first floor (although the total prospective load could be contained by 5 A circuit,
the consequences of a circuit failure plunging the whole dwelling into darkness should persuade the
designer to use two circuits).
*c) Immersion heater(s)(which must be on separate circuits, not connected to a ring main).
d) Kitchen/laundry area socket outlets.
e) Socket outlets ground floor.
f) Socket outlets-first floor. (Where applicable)
*g) Cooker circuit(s).
*Note: In rare cases.
6.2.7.3 Domestic socket outlet circuits

A domestic ring circuit may serve adequate number of sockets within a floor area of 100 m.
However consideration of the probable growth of electricity usage in future makes the use of two or
three ring circuits i.e. ground floor, first floor and kitchen, highly desirable.
Table 6 gives the number of socket outlets recommended in the new houses, and the desirable
minimum indicated by a reasonable consideration of the growth in ownership of appliances over the
next few years.
TABLE 6 - RECOMMENDED MINIMUM PROVISION OF SOCKET OUTLETS IN DOMESTIC

PREMISES
PART OF THE HOME
RECOMMENDED NUMBER OF SOCKETS
Kitchen
Dining room areas
Living rooms
Each bedroom
Hall
Storage or garage
4-8
2-4
5-8
2-4
2-4
12
Total for typical 3 bed house
16 30
Not only must the number and distribution of socket outlets provide for the appliances the
householder may own, it must also provide for the fact that the positioning of furniture and the
utilization of appliances varies from family to family with time. Flexible cords between sockets and
appliance must always be as short as possible and never longer than 1.5-2 meters, from which it
follows that a dual socket should be available within 1.5 meters of every point in a room at which a
future occupier may wish to utilize an appliance or portable luminaries.
It is not necessary for every socket outlet to be connected into a ring circuit.
Often it is not fully appreciated that an adequate number of socket outlets must be provided if an
installation is to be safe under all conditions. Apart from the convenience of being able to use
appliance in any required position, a reasonable number of socket outlets will eliminate lengths of
trailing flex and other dangers.
The mounting height of the fittings above finished floor level shall be as follows:
- Socket outlet (general)
- Socket outlet (in kitchen)
- Light switch
- Door bell push wall type
30 cm
110 cm
110 cm
110 cm
6.2.7.4 Special precautions in bathrooms

Socket outlets are not permitted in bathrooms nor within 2.5 meters of a shower cubicle or bath in a
bedroom. This is because the consequences of a shock when the person is wet, has bare feet or is
in contact with earthed metal are far more likely to prove fatal than if the same shock were
48
Feb. 2012
IPS-E-EL-100(1)
sustained elsewhere. For the same reason, lamp holders within 2.5 meters of a bath must be
shrouded or totally enclosed and no fixed wall switches or heaters may be installed within reach of a
person using a bath or shower. Pull cord switches are permissible and are indeed the preferred way
of meeting the switching requirements of a bathroom.
6.2.7.5 Sockets for outdoor installations

Weatherproof socket outlets according to demand shall be provided outdoor where deemed
necessary.
6.2.8 Power supply for high rise buildings

Power supply to different floors shall be via power cables. Alternatively bus trunking can be utilized
upon approval.
If cables are used each floor shall be fed by one individual feeder.
Normal loads shall be supplied from normal supply bus and emergency load shall be supplied from
emergency bus in normal conditions both buses are to be supplied from mains power supply. In
case of mains power failure an emergency diesel generator shall be started via a suitable mains
failure panel which opens the bus coupler and closes the emergency generator circuit breaker when
frequency reaches 50 Hz. On resumption of normal supply, the generator circuit breaker shall open
and busbar coupler closed through properly designed interlocks, after 3 minutes the diesel engine
shall stop. See Fig.3.
When requirement dictates power feeder shall be provided for:
1) Central cooling machinery
2) Ventilation
3) Smoke stack, fire pumps
4) Central power factor correction equipment
5) Lift(s)
49
Feb. 2012
IPS-E-EL-100(1)
TYPICAL ELECTRICAL SYSTEM IN HIGH RISE BUILDING

Fig. 3
6.2.9 Load increase in existing supply systems
In existing systems load increase can occur, e.g. due to extensions and modernization of dwellings
or commercial premises.
The expected load is calculated using an annual rate of increase based on the present load and
preceding development. Depending on the type of building development in the area of supply and
the probable in filling of vacant spaces, growth rates of between 2 to 5 % per year can arise.
Furthermore, without a general load increase due to alterations or change of consumers, local
deviations of the load must be expected requiring a suitable extension to the system.
6.2.10 Selection of equipment

The fundamental consideration in selecting equipment is to choose optimum equipment consistent
with the requirements of the buildings. Frequently it costs no more in the long run to use the best
equipment available as it pays dividends in service continuity and lower maintenance.
The following design notes shall be considered:
a) Metal clad switchgears for medium voltage and low voltage main distribution boards.
b) Metal enclosed for low voltage subsidiary distribution boards.
c) Dry type transformers for substations in or attached to buildings.
d) Factory assembled equipment for easier field installation and better coordination as far as
possible.
e) Copper conductor, armored cable for medium voltage and low voltage.
50
IPS-E-EL-100(1)
Feb. 2012
f) Galvanized steel conduit and fittings for the electrical installation of buildings.
g) i- Minimum cross section for ring circuit of socket is 2.5 mm
ii- Minimum cross section for lighting fixtures is 1.5 mm
h) The size of conduit should be designed such that at most %40 of the cross section is occupied.
6.3 Electrical Apparatus for Potentially Explosive Gas Atmospheres

For this section refer to latest revision of IPS-E-EL-110.
7. DESIGN AND SELECTION REQUIREMENTS FOR EQUIPMENT
7.1 Electric Network Supply and Emergency Systems (Diesel Generator )
7.1.1 Scope
This standard covers the minimum requirements for design of industrial revolving field, cylindrical
pole construction, self exciting, brushless self regulating L.V. and M.V. & 3 phase (4 wires in L.V.)
50HZ 4 pole 1500 R.P.M. at 0.8 lagging P.F. AC generator.
7.1.2 Design and construction of alternator
7.1.2.1 General
1) All machines shall be of continuous running duty S1 and continuous Max. rating in addition diesel
driven units shall be capable of running at full. Load for one hour in every twelve hours.
2) The ingress degree of protection for rotating machines shall be IP54. The degree for all other
electrical equipments shall be as followings:
Off shore
outdoor locations
IP55
On shore
outdoor locations
IP54
On/Off shore
Indoor locations
IP42
Between adjacent compartments in electrical apparatus
IP40
3) Rotating machines which are to be located in a hazardous area shall be provided with and
appropriate type of protection.
4) The generator and its auxiliaries shall comply with IPS-M-EL-138 and part 7.1 of this standard
and may be used for based load generation or standby duties based on technical/economical
studies.
5) For generators above 1250 KVA, each generator set shall be provided with its own LV auxiliary
switchboards for the supply and control of all its motor driven auxiliaries. This switchboard should
be treated as an essential services switchboard.
7.1.2.2 Stator winding

1) Stator windings shall be fabricated from copper conductors.
2) The insulation class shall be F with design temperature rise limited to class B.
51
Feb. 2012
IPS-E-EL-100(1)
7.1.2.3 Rotor
1) The shaft shall be precisely machined from high quality steel and adequately hardened and shall
carry the rotating field system , DC exciter rotor winding rotating three phases roll wave rectifier
assembly and cooling fan.
2) The complete rotor assembly shall be securely braced and statically and dynamically balanced
on completion. Balance weights shall be of non ductile material such as lead. And rotor design
shall allow for balance weights attaching if necessary.
3) The direction of the air flow shall be such that the discharged air does not pass over the driver.
The ventilation system shall include air intake filter.
4) The rotor shall include excitation system independent of external power supply.
5) Winding conductor of the rotor shall be copper with mica paper, glass cloth and epoxy resin
insulations. Impregnation and curing shall be either by the resin method or vacuum. And shall be
baked and treated to provide a hard setting , oil and moisture resistant anti-tracking finish suitable
for a dusty saline and tropical environ meant.
6) The direction of rotation shall be clearly and permanently indicated by means of an arrow on the
external surface of the frame at the N.D.E. painted or adhesive tape methods of indication are not
acceptable.
7.1.2.4 Main terminals

1) Terminal box and cable terminations shall be suitable for operation at given faulty level.
2) Means shall be provided for electrically isolating individual windings from each other and from the
main outgoing connections without involving motor dismantling of the machine or risking damage to
the windings or connections.
3) Space shall be provided for the installation of current transformers.
4) Terminal box shall be of air insulated pattern in which the protection of passes conductors
against electrical short circuit is done by adequately spaced bare conductors with appropriate
insulated supports.
5) Terminal marking. Shall be U-V-W and provided in a clear and permanent manner.
6) Terminal arrangement shall have adequate space to accommodate easily the size and type of
cable required.
7) Mechanical metallic glands shall be provided for the type and size of cable required.
8) The earthing terminal shall be external to the terminal box.
9) Heater and any other additional connections shall be clearly identified.
separated and terminals fully shrouded.
Circuits shall be
7.1.2.5 Exciter and automatic voltage regulator

1) The excitation system shall be of brushless type and power for field excitation shall be supplied
from the shaft driven pilot exciter.
2) The system should be complete without needing external power supply, and power may be
derived from generator terminals.
3) The excitation system shall be capable of providing at least 3 times the rated current under three
phase terminal short circuit conditions for at least 10 seconds.
4) A timed current limiting circuit shall be provided if static thruster exciter is required to prevent
sustained overload.
5) It is necessary to initially provide a high excitation current during fault conditions to supply
additional reactive power demanded during fault condition and to maintain a synchronous torque at
52
Feb. 2012
IPS-E-EL-100(1)
low voltage levels rotor current limitation is necessary to prevent the undesirable disconnection of
the generator due to overload of the rotorcraft current.
6) The A.V.R. shall be of solid state design and including protection against over voltage and be
provided with means to adjust the set point of the main generator output voltage over a range of
+10% nominal voltage rating at full load.
7) The A.V.R shall have an adjustable reactive current droop characteristic and be suitable for
reactive load sharing known as quadrate current compensation (Q.C.C.) providing the ability for
generators in parallel to share reactive currents in equal of proportional amounts.
8) The A.V.R shall allow 100% voltage to be generated at 80% of speed under all conditions of
operation.
9) Over fluxing control shall be provided, this shall not reduce excitation until frequency is less than
75% of rated frequency.
10) Max. excitation limitation and max. Volts/hertz facilities shall be included within the A.V.R. unit.
11) Temp. stability of the voltage regulation shall be better than 0.5% for temperature between max.
and min. of ambient temperatures.
12) The A.V.R shall regulate the voltage within 2.5% of the set point between No-Load and full-load
and for all speed droop variations. The regulation capability of the AC generation and A.V.R system
under transient conditions shall be arranged such that following any transient disturbance, voltage
shall be restored to 2.5% within 10 seconds, and voltage will be restored to 97% of nominal voltage
within 1 second.
7.1.2.6 Built-in temperature detection

1) Stator winding shall include built-in thermal protection, two levels of detection, alarm and trip.
The alarm and trip setting differential should be such that adequate time would be available for the
plant operator to shed load in the event of slow overload. Trip setting, slow and rapid should be as
high as practicable under all operating conditions.
2) A minimum of six resistances temperature detectors shall be provided and spaced equally
around the circumference of the stator, and two for bearings.
3) All detectors leads shall be metric. Armored detectors shall be located between coil sides in the
stator slots with their centers at the longitudinal midpoints of the stator.
7.1.2.7 Bearings and lubrication

1) For emergency generator applications self lubricated bearings are preferred. Hydrodynamic
radial bearings shall be fitted to all machines of 1 moa rating and above with R.T.D. for 2 moa and
above.
2) On both oil and grease lubricated bearings it shall be possible to re lubricate in safety without
stopping the machine. Where oil lubricated bearings use level indicator or a non rest active oil flow
indicator to each bearing shall be provided.
3) where hydrodynamic radial bearings are fitted they shall be provided with local dial type
thermometers with detachable stainless steel thermo wells and accuracy within 1% range over
scale to read oil bath or oil outlet temperatures.
4) Machines without thrust or location bearings shall be stated. As such in the initial proposal and
on the manufacturers drawing. The machine shall be coupled to the driver by limited end float
coupling. The machine rating plate shall be marked ("limited end float" (L.E.F).
5) The correct running positions on the rotor shall be permanently marked together with the limits of
permissible movement. It shall be possible to deserve the rotor position at all times relative to the
above marks.
6) All bearings shall be fully insulated from the machine carcass and/or bedplate to prevent a flow of
shaft current unless type tests demonstrate that the shaft voltage measured at any load across the
53
Feb. 2012
IPS-E-EL-100(1)
ends of the shaft is less than 150mv-rms. The insulation method shall be permanent and non-deter
10 rating. This shall include any lube oil supply and drain connections to the bearing housing.
7) Machines shall be tested with their service bearings fitted. If transit bearings or other devices are
employed for transport purposes, clear labels starting this shall be affixed to the machine.
8) Bearing housings shall have provision for mounting two shaft proximity type vibration probes at
each radial bearing with the probes mounted 90 + 10 circumferentially apart and shall be furnished
with standard breather.
9) All bearings shall provide shaft access for vibration measurement through or adjacent to the
bearings.
10) The critical speeds of the rotor shall not be within 20% of any speed in the operating range nor
within 20% of two times operating speed range.
7.1.2.8 Machine cooling

1) Machine cooling shall be either by air or water. Air cooling is the preferred method. Whenever
water cooling is utilized, A leak detection system shall be provided and measures taken to prevent
damage to the machine in the event of a leak and shall include temperature detecting system with
contacts for alarm annunciation.
2) Precautions shall be taken to ensure no corrosion occurs due to contact between dissimilar
metals.
3) Water cooling system shall be included as part of the package. In water cooling, water supply
shall not be derives from outside the package excepting the case of an off skid located radiator
water coolers shall be side or bottom mounted. Top mounted water coolers are not acceptable.
4) Coolers shall be so designed that if one section is intended to be taken out of serve for cleaning
the unit can carry at least two third of the rated load continuously without the permissible
temperatures of the active parts of the machine being exceeded.
5) The following elements should be considered in water cooling:
a) Cooling water supply pressure
b) Cooling water supply pressure
c) Test pressure , that should be twice the working pressure
6) Fans for generators cooling shall be brass, bronze or aluminum. Plastic or non metallic fans and
housing are not acceptable. And shall be of non sparking material.
7.1.2.9 Earthing
1) The neutral point of the alternator in the connecting terminal box shall be grounded solidly or
through resistor.
2) Generator frame and skid shall have grounding bolts to be grounded.
Connections to the bearing housings of generators having insulated bearing pedestals shall ensure
that no connection, including that of the bearing sheath, provides a by pass around the insulation.
2
The generator shall be provided with at least two main earthing points to which 70mm copper cable
strip will be made. The location of the earth points shall be in an accessible place to enable
external connections to be made and subsequently inspected or tested. Any equipment which is
part of main generator skid shall be effectively bonded to the base frame. Any electrical equipment
which will be separately mounted from the base frame shall have provided, means for earth bonding
to the main frame.
Earth bonding by holding down bolts will be generally acceptable. However particular attention
should be made to the arrangements for bonding that equipment which may rest on insulating antivibration mountings. For these applications a supplementary earth bond may be necessary,
particularly if the item of equipment has an electrical supply.
54
Feb. 2012
IPS-E-EL-100(1)
7.1.2.10 Lifting points

1) All equipment shall be mounted on a single skid frame. The skid frame shall be provided with
lifting lugs to enable the package to be moved by the use of an over head crane.
2) Lifting points shall be an integral part of the generator frame. Where this is not the case and the
lifting is by the use of eye bolts, these shall be collar pattern.
3) All necessary spreader beams, slings, shackles and lifting gear shall be provided to enable the
package to be hand kept at the jobsite and all necessary specular tools to enable maintenance to
be carried out.
4) Facilities shall be provided for the application of jacking screws in all three planes, and their
location marked on the machine general arrangement drawings.
5) Where it is intended to use spreader bars for lifting all or part of the machine or where other
spicier handling precautions are necessary these requirements shall be identified on a suitable plate
attached to the external surface of the machine.
7.1.2.11 Generator control panel

1) The package shall be provided with its own unit control equipment logic system and alarm
annunciation necessary for the protection and operation of the compete set as an integral part of
the package.
2) The control panel shall be installed in a front access cubicle. And shall have an Ip55 enclosure
and be suitably protected against a saline atmosphere. It shall be made from 2.5mm steel sheet.
The unit control panel shall be mounted either on or off the equipment skid. If the panel is mounted
on the skid it shall be protected from vibration by means of suitable anti vibration mountings.
3) If the panel is mounted remotely from the skid all cables etc. Shall be routed to a junction box
located on the skid and the panel shall have a matching junction box.
4) The control panel shall be protected by a canopy. The control panel doors shall be hinged and
lockable. The enclosure shall be constructed and assembled so that it will have the strength and
rigidity necessary to resist the abused to which it is likely to be subjected without total or partial
collapse resulting in a risk of fire, electric shock or injury to persons due to reduction of spacing,
loosening or displacement of parts or other serious defects.
5) The control panel shall typically include the following:
a) AC generator synchronizing and alarms.
b) AC generator voltage regulation.
c) AC generator protection.
d) Speed raise/Lower.
e) Voltage raise/Lower.
f) Emergency stop push button.
g) Normal start/Stop push buttons.
h) Trip/Close switch and position indicator for generator circuit breaker.
i) Local/Remote control selector.
j) Excitation manual/Off/automatic(are) selector.
k) Start selector manual/Auto-standby/Off.
l) Jacket water heater switch.
6) If manual synchronizing facilities are included in the scope then check synchronizing relays shall
also be included in the scheme.
If automatic synchronizing facilities are included Then manual synchronizing backup together with
check synchronizing relays shall also be provided.
55
Feb. 2012
IPS-E-EL-100(1)
7) The drivers of all machines shall be fitted with speed governing equipment.
Where the generator is to operate in isolation the governor shall provide isochronal oust control.
8) Where the generator is to operate in parallel with other generators then adjustable droop control
shall be provided.
9) Facilities shall provide to repeat informations and alarms to a remote control room, each alarm
signal shall be wired to output terminals in the unit control panel. A common remote alarm facility
shall also be arranged.
10) The following are accessories which may be selected depending on rating, voltage and
application of specific cases:
a) Power factor meter.
b) KVRH meter.
c) KWH meter.
d) Generator voltage.
e) Generator current.
f) Frequency meter
g) Hours run counter
h) Under/Over frequency protection.
i) Short circuit sustaining protection.
j) Ground fault protection.
k) Surge protection.
l) Differential protection.
m) Lightning arrested.
n) Synchronizing check recap.
o) KW Indicator.
p) Aver/Manual excitation null balance meter.
q) Running and incoming volt meters.
r) Running and incoming frequency meters.
s) Exciter field volt meter.
t) Exciter field ammeter.
u) Synchronizing lamps.
v) Alarm indications.
w) Synchrony scope
11) Electrical instruments shall be of the flush mounted, industrial grade, enclosed in dust and damp
proof casing, non projecting dial with non-glare, non-reflecting windows.
12) All abnormal conditions which would ultimately lead to a shutdown shall have warning pre
alarms where possible the interval between set points shall be sufficient for corrective action to be
taken.
13) In the event of an equipment trip a "first out" facility shall be provided to identify the original fault.
14) Repeat volt free contacts shall be provided for remote indication of each alarm and shutdown
condition wired to panel outgoing terminal.
15) Facilities shall be provided to permit remote acceptance of alarms.
16) For analogue additional remote signals 4-20mA transducers shall be used.
56
Feb. 2012
IPS-E-EL-100(1)
17) In the event of an automatic shutdown due to low engine lube oil pressure, over speed or high
jacket water temperature attempts to restart shall be automatically inhibited until the trip has been
locally reset.
18) All shutdowns except over speed, shall be via fuel cutoff, over speed shutdown shall be by both
fuel shutdown and air intake close up.
19) The package control system shall be fitted with a local/Remote control switch and a
manual/Auto standby/Off control switch, both switches shall be mounted on the control panel.
20) Local start and stop shall be by push buttons on the unit control panel, the local stop signals
shall be operative in both the local and remote modes of control. Terminals shall be provided for
multiple remote start and stop signals.
21) Facilities shall be provided for remote emergency shutdown of the set from the emergency
shutdown system.
22) With the local/Remote switch in the "Remote" position, remote control shall only be effective
with the remotely located mallow switch in the (Auto) position under these circumstances the
remote control shall enable a manual over ride start is the auto-start has failed a manual stop shall
also be provided at the remote control point. The auto start shall be initiated by a maintained close
to start contact.
23) In the "manual" or "auto standby" modes the generator shall automatically run up to the selected
speed upon start initiation.
24) As specific requirements facilities shall be provided for data logger and ground fault resistors.
7.1.2.12 Vibration
1) Bearing housings for hydro dynamic radial bearings shall have provision for the fitting of noncontacting dual proximity type vibration probes or accelerometers (rms velocity readings).
2) In a manner similar to temperature monitoring a complete package vibration monitoring system
shall be required.
3) The vibration amplitude of machines fitted with non-contacting vibration monitoring equipment
shall not exceed peak to peak level (unfiltered) of 63 micrometers including mechanical and
electrical run out. Total run out shall not exceed 13 micro meters.
4) The vibration level for machines fitted with flexible rotors passing through the first critical speed
shall be within the following limits:
a) Machines fitted with hydrodynamic bearing:
The peak to peak amplitude shall be less than 75% of the nominal bearing clear acne.
b) Machines fitted with rolling element bearings.
Less than three times the limits given below
The vibration limits for all machines not flitted with non contact vibration monitoring equipment shall
meet the requirements of bus 1999 part149 as follows:
For a shaft height less than 400mm table1 quality R.
For a shaft height 400mm or greater table2 column 1.
7.1.2.13 Noise
1) The Max. noise level at 1m away from the machine shall not exceed 85 db(A) when operating as
an alternator at rated voltage, rated speed at no load.
2) The noise emissions details of the machine shall be provided in octave bands. Also any narrow
band noise details that are noticeable to the ear shall be provided together in octave band or in
bands in which it occur.
57
Feb. 2012
IPS-E-EL-100(1)
3) Where the noise limiting requirements can not be met without the provision of noise reducing
features the levels with and without these features shall be stated.
Details of any noise reduction features shall be provided.
7.1.2.14 Rating plate

1) A metallic corrosion resistant rating plate shall be fixed on the generator frame and shall give the
following information's in English:
a) Manufacturers name
b) Customer order No. and date
c) Type and frame size and serial No
d) Year of Manufacture
e) Rated output in KVA
f) Rated power factor
g) Rated voltage
h) Rated frequency
i) R.P.M. at rated output
j) Class of insulation
k) Rated current
l) Transient and sub transient reactance
m) Standards reference numbers and date
n) Phase rotation clockwise or counter clockwise.
o) Exciter voltage and current at rated output
p) Weight of rotor and stator in KG.
7.1.2.15 Enclosure
1) The enclosure shall be designed as an integral part of the package.
2) Outdoor installations would normally be expected to be supplied with an enclosure in order to be
weather proof. Indoor locations may be specified without enclosures and may involve separate
mounting of the cooler radiator, master fuel tank and exhaust system.
3) For offshore installations the enclosure walls shall have a minimum fire rating of A60 and shall
comply with local regulations.
4) The enclosure shall be designed to allow adequate access for routine maintenance and
operation and shall be equipped with as minimum lighting/ lighting points, over head lifting beams
and drainage.
7.1.2.16 Ventilation
1) Where diesel engine powered emergency generator package have an integral enclosure, a
ventilation system shall be provided to maintain the temperature of the enclosure at an acceptable
level during operation.
2) The ventilation fan shall be driven off the engine either directly or by the use of hydraulic
transmission, alternatively an electric motor drive may be used with power derived direct from the
generator via a local starter.
58
Feb. 2012
IPS-E-EL-100(1)
3) Where union closed diesel engine powered emergency generators are installed in dedicated
rooms any requirement for connections (e.g. power and control) to ventilation system will be
specified.
7.1.2.17 Lighting and small power

1) Enclosures which personnel may enter for operation or On-line maintenance shall have
emergency lighting.
2) The preferred type of luminary is fluorescent. The emergency luminaries shall be supplied either
from a central battery system or the integral battery type shall be used.
3) At least two normal lighting circuits shall be installed and both circuits shall be utilized in all
areas.
The design shall allow maintenance and modification of one grout whilst the second circuit is in
operation.
4) Small power outlets shall be provided and distribution within the package shall be by the vendor.
5) Electrical power for battery charger shall be derived from a single supply to the package.
7.1.3 Design and construction of diesel engine
7.1.3.1 Performance
1) The engine continuous net brake power, fuel consumption and lubricating oil consumption and
overload power shall be declared under ISO conditions. It is to be recognized that the unit should be
capable of the emergency duty as required at the site max. ambient conditions.
2) The engines continuous net brake power at all operating conditions shall be sufficient to enable
the generator to produce power as specified in the name plate rating.
7.1.3.2 Starting system

1) Each engine shall be provided with a starting system, the preferred system shall be electric,
based on the use of batteries.
2) Often, emergency generators are auto started. Where the start system proves inadequate for the
task, manual start would need to be under taken.
3) Power for successive cranking cycles shall be provided by a battery unit having sufficient
capacity, at the site extremes of temperature, to maintain the cranking speed recommended
through a 192 seconds cycle (8 seconds cranking and 7 seconds rest in 12 consecutive cycles).
Where auto started, the engine shall attempt 9 of the possible 12 starts and then show a fail alarm.
The remaining 3 start attempts shall be individually initiated manually. Where the emergency
generator 15 considered sufficiently critical, all 12 automatic start attempts may be specified for the
primary starting.
4) All batteries shall be of the recombination cell type. Sealed lead Acid battery type represents
the usual recombination type of battery expected and nickel cadmium types would represent the
highest reliability, performance and expected lifetime.
5) On offshore installations the starting battery shall be capable, of being isolated by a remotely
controlled contactor contained within an axed enclosure. The contactor shall be used for isolation
purposes only. Control of this contactor will be from the installations fire and gas detection system.
6) It is expected that the battery system provided would be equipped with suitable electrical
protection devices ictuses or circuit breakers would be acceptable, and that the battery wiring would
be sensibly arranged to eliminate the probability of short circuits.
7) An independent dedicated constant voltage type charger and charge control system shall be
provided, each charger shall comply with the following:
59
Feb. 2012
IPS-E-EL-100(1)
a) Have aerate of charge consistent with:

- Recharging the respective battery in the minimum time.
- Not causing damage to the battery
- Not reducing battery design life
- Restoring full charge to the battery within 24 hours following any stylize of discharge.
b) The charger shall be marked with the ampere-hour rating of the largest capacity battery that it
can recharge in compliance with (a) above.
c) An ammeter with an accuracy of 5% of the normal charging rate shall be furnished to indicate
the operation of the charger.
d) Have an electrical supply which is independent of the terminal output of the emergency
generator.
There should be adequate safety notices arranged on the emergency generator charger to show
the system is live unless isolated elsewhere.
7.1.3.3 Cooling system

1) Either direct air cooling or water cooling of the engine is acceptable provided they are of the
manufacturers standard design.
Water cooling system shall be sized for the engine continuous net brake power at the max.
Ambient and cooling water temperatures. The system also include capacity for cooling the air
within the engine/generator enclosure or room and for cooling the engine exhaust, as an alternative
separate system may be proposed for each duty.
2) Under some circumstances it may prove necessary for the exhaust of the engine to be cooled
sufficiently to ensure that the temperature is below the ignition point of the hydrocarbon explosion
hazard this may be achieved with the aid of a water bath around the exhaust manifold.
3) The radiator fan shall be driven from the engine either directly or electrically taking power direct
from the generator but put terminals or by the use of hydraulic transmission.
It shall not be independently powered.
4) The engine shall be provided with thermostatically control jacket water heaters and is necessary
a circulating pump, to ensure optimum engine starting temperature at the minimum specified
ambient temperature.
5) Where a water circulating pump will be provided and independently powered from the utilities
supplies to the emergency generator package, the voltage of the motor should be selected in
accordance with the information regarding utilities.
6) If necessary provision shall be made for the prevention of over heating of the coolant due to
local high temperature after shutdown.
7.1.3.4 Fuel system

1) Each diesel engine shall have a dedicated fuel storage tank it shall be sized to provide a net
capacity of fuel in accordance with statutory regulations (e.g. for offshore use 24 hrs base down fuel
consumption at engine continuous net rated power). It is to be recognized that emergency diesel
generators would generally be expected to have a dedicated "Day Tank" and therefore any
additional diesel storage and fuel forwarding system should incorporated the tank within the overall
design.
2) Under no circumstances shall the tank be located above the hot exhaust ducting or the engine
itself. Where the fuel tank cannot be accommodated as an integral part of the emergency generator
skid, the location will be arranged according to the available space availability tanking into account
other plant and services.
60
Feb. 2012
IPS-E-EL-100(1)
3) Where a gravity fed fuel systems are employed a locally operated manual valve shall be installed
in the fuel line to the engine at the tank outlet. If the tank is located within the room / enclosure this
valve shall also be operable from outside the room / enclosure.
4) The tank shall be provided with a man way opening , and connections for filling swan neck vent
flow, return, drain, over flow and instrumentation e.g. level gauge and high/low level alarms.
5) A thermo statically controlled tank heating system shall be provided if ambient conditions could
result in the viscosity of the fuel.
6) The fuel suction filters shall be of the duplex type with replaceable elements and a changeover
facility to permit removal and replacement of dither element without need for engine shutdown.
Filter mesh size shall be specified.
7) Provision shall be made for priming and bleeding the fuel injection system.
8) For unmanned installations high pressure fuel lines between remote fuel pumps and injectors
shall be double skinned, seamless tubing with fuel leak monitoring and alarm. On manned
installations the fuel lines may be as above or heavy seamless tubing.
9) Flame resistant flexible hoses shall be provided within the fuel supply and return piping systems
between the engine and off skid pipe work at the EDGE of the engine skid. There shall be no shut
off valve in the return line to the tank.
7.1.3.5 Exhaust system

1) The exhaust system shall include silencers, bellows and spark arresters.
generator packages are provided each engine shall have its own exhaust system.
If two or more
2) The discharge location from the exhaust system will be specified. The extent of the vendors
supply will be identified.
3) Hot exhaust system piping within the confines of the package and constituting a danger to
0
personnel shall be insulated or protected to limit surface temperature to 65 C.
4) Where exhaust systems can be exposed to hazardous area conditions, they shall be water
cooled to limit surface temperature. The temperature and the length of the system requiring cooling
will be specified.
7.1.3.6 Air intake system

1) Dry replaceable filters shall be provided for the combustion air intake. Filter condition gauges
shall be provided. The location of the air intake should be arranged to be in a "SAFE" area with no
possibility of hydrocarbon ingestion.
2) An automatic shut-off valve actuated by engine over speed shall be filled in the air intake
manifold. Operation of the valve shall be independent of external power sources and shall be
capable of manual operation.
7.1.3.7 Lubrication system

1) Lube oil filters shall be of the replaceable element type, and shall be equipped with relief valves
and , if no other label oil pressure indication is provided, a differential pressure gauge, filters shall
be of duplex type with manual changeover facility.
2) Engines shall be suitable for starting under all conditions without the need for engine pre-lube.
3) Electric sump heaters, if provided, shall have a power density not exceeding 2.3 W/cm
7.1.3.8 Couplings
1) It shall be possible to remove couplings without the need to move the engine or driven
equipment.
61
Feb. 2012
IPS-E-EL-100(1)
2) All flexible couplings incorporating a spacer piece shall be of a design in which the spacer piece
is positively constrained from flying out in the event of failure of the flexible elements.
3) The max. coupling torque shall be limited to a max. of 80% of the coupling rating.
7.1.3.9 Torsion vibration and critical speed

1) The engine shall be carried out a torsion vibration analysis for each complete equipment string
and shall be submitted for review.
2) Each engine, coupling, driven unit system shall be so designed to ensure that the complete
installation starts, operates and stops free from torsion vibration and oscillation, the first lateral and
torsion critical speeds for the max. Operating speed no lateral or torsion critical speed shall lie
within the operating speed range of the system.
3) Diesel engine rams velocity of vibration shall not exceed 11.2 mm/s at any operating condition.
7.1.3.10 Speed control

1) Under normal steady state operating conditions the governor shall maintain the frequency of the
generators electrical output within 1% of the value identified for all loading conditions. A full load
rejection shall be possible without causing an over speed trip.
2) Speed droop will be necessary whenever the emergency generator is required to operate in
parallel with the power system (for testing and re-instatement purposes). Under these conditions
the speed droop should be set at 4%.
3) A mechanically initiated over speed protection system is expected for engine protection.
Additionally an electronic over speed protection controller should be contemplated. The settings of
the devices should be arranged with at least 5% speed between their in initiation.
4) When starting the largest size motor identified. The generators output frequency shall not dip by
more than 5% this requirement shall be based upon the assumption that the motor shall be started
with the generator fully loaded except for the motor under start.
5) A standard value of 10% speed variations for a step load of 100% would be common for naturally
aspirated engines with the step load equating to this speed variation being a function of turbo
charger performance for those engines provided with turbo chargers. An electrical motor direct on
line start would present the engine with up to 25% of its rated demand at one point of its starting
transient. The 5% speed variation is based on national electrical power system expectation and
may be relaxed to 10% if electrical loads supplied by the particular emergency generator can accept
such frequency deviations.
7.2 Switchgear, Controlgear and Substations
7.2.1 General
Low voltage switchgear and control gear constitute the link between on the one hand the means of
generation (generators) transmission (cables) and, voltage transformation (transformers of electric
power and on the other hand the consuming equipment such as motors, lighting, heating and air
conditioning plant.)
The selection criteria grouped in five categories
7.2.1.1 Current
- Rated current of busbar
- Rated current of in feeds and bus section
- Rated current of outgoing feeders
62
Feb. 2012
IPS-E-EL-100(1)
- Short circuit withstand capability of busbars

- Short circuit breaking capacity of circuit breakers
7.2.1.2 Nature of protection and installation

- Degree of protection
- Method of installation (against a wall, or free standing)
- Number of operating faces
- Enclosure material
- Protective measure
7.2.1.3 Equipment mounting

- Fixed
- Withdraw able
7.2.1.4 Application
- Main switch board
- Industrial distribution board
- Non-industrial distribution board
- Motor control center
- Power factor correction equipment
- Control board
7.2.2 Recommendation for selection
7.2.2.1 The equipment shall be a factory built assembly (F.B.A) from manufacturer capable of
providing an acceptable technical and commercial back- up service.
7.2.2.2 Selection of main power distribution board and M.C.C

The following parameters shall be considered for selection of switchgear:
- The highest current rating of the equipment up to 4000 amps.
- Sheet steel or alozinc as the enclosure material
- The maximum height shall be in accordance with IPS-M-EL-143(2)
- Short circuit withstand capability up to 50 kA rms
- Mounting method for equipment:
Withdraw able
- Enclosure protection IP42 (indoor)
7.2.2.3 Selection of non- industrial distribution board

The flowing shall be considered in selection of distribution boards:
- Rated current of up to 1250A.
63
Feb. 2012
IPS-E-EL-100(1)
- Sheet steel as the enclosure material.

- Maximum height of distribution board 220 cm.
- Equipment items mainly fixed.
- Short circuit capability up to 50KA
- Ingress protection IP42 for indoor and IP55 for under shelter installation.
7.2.2.4 Selection of industrial distribution board and M.C.C

- Rated current of up to 1250 A.
- Sheet steel as the enclosure material.
- Height of individual less than 170 cm
- Equipment items mainly withdrawable.
- Short circuit withstands capability based on area condition:
a) Up to 50KA for safe areas.(base on calculation)
b) Maximum 25ka for explosive hazardous areas.
- Ingress of protection IP42 for indoor and IP 55 for under shelter and IP 65 for on protected
installation.
7.2.2.5 Current rating and short- circuit withstand capability

Circuit breakers in accordance with the data sheet shall have normal current rating selected from
the following ratings:
630, 800, 1250, 1600, 2000, 2500 and 4000 amperes.
The above mentioned figures shall be derated for maximum summer temperature i.e.50 c .Short
circuit breaking and making rating current shall not be less than 50 KA and 150KA respectively for a
fault capacity for 3 seconds unless otherwise Determined under different circumstances.
Where switchgear and controlgear assembly motor control centers are located in explosive
hazardous areas they shall be explosion proof, and fault current shall not exceed 25 KA for 1
second.
7.2.2.6 Protective measures

All metal parts of switchgear assembly and distribution boards shall be provided with protective
conductor (PE).
7.2.2.7 Selection of apparatus to zone of hazard

For selection of apparatus in hazardous area refer to IPS-E-EL-110(1).
7.2.3 Feature to Be Considered in Installation, Access and Controls circuit.
7.2.3.1 Type of installation

- On the floor against wall
- On the floor free standing in the room.
- Fixed to a wall or a recess for non-industrial board.
7.2.3.2 Nature of access.
64
Feb. 2012
IPS-E-EL-100(1)
- Front or rear access for cable connections and alteration.

- Top access for modification to or installation of busbar.
7.2.3.3 Special requirements
Possible special requirements such as for example explosion protection, against hostile
Atmospheres and earthquake shall be considered in design stage.
7.2.3.4 Outgoing feeder circuit breaker rated up to 400 ampere can be molded case circuit breaker
(mccb) type, when approved by company representative.
7.2.3.5 The voltage of the spring motor as well as the circuit breaker close and trip voltage shall be
110 volt dc supplied from the substation dc Power supply system.
230V.AC can be utilized for the spring charging motor if approved by company representative.
7.2.3.6 All remote controlled circuit breaker and contactors shall have the closing device local to
the panel either omitted or made inoperable when the circuit breaker or contactor is in the normal
operating position.
7.2.3.7 A motor starter shall normally be opened and closed from a control station adjacent to the
motor.
7.2.3.8 Any emergency stop control for motor starters shall form part of the primary stop control
circuit and the use of interposing circuit or relays shall be avoided.
7.2.3.9 For motor contactor units directly controlled via control circuits over 600 meter long the
following alternatives shall be considered:
i) The use of interposing relays.
ii) 110V DC control.
7.2.3.10 The voltage drop for the control circuit supplied controlled shall not be exceed 5%
7.2.3.11 Adequate clearance shall be provided around the switchgear for maintenance, operation,
access and anticipated extensions.
Note:
In absence of local regulation minimum clearance of 1.5 meter shall be considered in front of
switchboards. When withdraw able equipment is fitted a minimum clearance of 1.5 meter
shall be allowed when the equipment is fully withdrawn. a minimum clearance of 0.8meter
shall be allowed at the rear of switchboards.
7.2.4 M.V. & H.V. switchgear
Selection Criteria For M.V. And H.V. Switchgear
7.2.4.1 Busbars
7.2.4.1.1 Switchgear Installations for normal service conditions should be preferably equipped with
single busbar systems.
These are clean in their arrangement simple to operate, Require relatively little space and are low in
initial cost and operating expenses see Fig. 4.
65
Feb. 2012
IPS-E-EL-100(1)
SINGLE-BUSBAR WITH BUS-TIE BREAKER

Fig. 4
7.2.4.1.2 Double busbar switchgear and controlgear (switchboard)

double busbar switchgear and controlgear can offer advantages in the following:
- Operation with asynchronous feeders.
- Feeders with different degrees of importance to maintain operation during emergency conditions.
- Isolation of consumers with shock loading from the normal network.
- Balancing of feeders on two systems during operation.
- Access to busbars required during operation see Figs. 5 and 6:
DOUBLE BUSBARS WITH DUAL FEEDER BREAKERS

Fig. 5
DOUBLE BUSBARS WITH SINGLE FEEDER BREAKERS

Fig. 6
66
Feb. 2012
IPS-E-EL-100(1)
7.2.4.2 For all of the above mentioned switchgear and controlgears the following rating terms may
be used:
Rated Frequency
The standard values of the rated frequency for MV/HV pole switchgear and controlgear are 50 Hz.
Rated Normal Current

The rated normal current of a switching device is the rms value of the current which the switching
device shall be able to carry continuously under specified condition of use and behavior. The values
of rated normal current shall be selected from the R 10 series specified in IEC 60059.
The Rated Voltage

The rated voltage indicates the upper limit of the highest voltage of systems for which the
switchgear and controlgear is intended. Standard values of rated voltages are given below:
3.6 kV. , 7.2 kV. , 12 kV. , 24 kV. , 36 kV. , 72 kV .
7.2.4.3 Choice of interrupters

Depending on the switching duty in individual switchboard and feeder basically the following types
of primary interrupters are used in the switchgear cubicles. M.V. and H.V. switchgear for indoor
installation shall comply with IPS-M-EL-144(2).
7.2.4.3.1 Vacuum circuit breakers

Vacuum circuit breakers shall be used for all general purpose applications for indoor HV. and M.V.
switchgear.
7.2.4.3.2 SF 6 circuit breakers

SF 6 circuit breaker proposed as an alternative option in system voltage above 24 kV.
7.2.4.3.3 Vacuum contactors

Vacuum contactors are used for frequent switching operations in M.V. motors, transformers and
capacitor bank feeders up to 1000kW/1000 KVA /1000 KVAR. These are reliable and compact
device with maintenance free interrupters.
Since contactors cannot interrupt fault current they must always be used with current limiting fuses
to protect the equipment connected.
Note 1:
Out door switchgear shall only be considered for voltage exceeding 36 KV.
Note 2:
For existing extension or where the incoming circuit is one feeder and one transformer,
33KV/20kV and 11 KV may be used as outdoor switchgear.
67
Feb. 2012
IPS-E-EL-100(1)
7.2.4.4 Control requirements
7.2.4.4.1 Circuit breakers shall be controlled from remote control panel in a separate room.
7.2.4.4.2 Control of a motor starter shall be from a control station adjacent to the motor or control
panel in allocation remote from both the motor and starter equipment (ex. Control room)
7.2.4.4.3 stop control for motor starters located beside The shall form part of primary stop control
circuit and the use of interposing relays shall be avoided, if an interposing relay is unavoidable then
the circuits shall be fail safe.
7.2.4.4.4 For motor contactor unit directly controlled via control circuits over 600 meter long, the use
of interposing relay and/or 110 v.DC control shall be considered.
7.2.4.5 Switchgear installation
7.2.4.5.1 Access
Adequate clearance shall be provided around the switchgear for maintenance, operation, access
and anticipated extensions.
7.2.4.5.2 A minimum clearance of 2.5 meter in front and 1 meter in rear of switchboards shall be
considered. the appropriate distance in both end of switchboards shall be considered for future
extension. The minimum clearance for both ends shall be 2.5 meter to the wall. The equipment
manufacturer shall always be consulted for recommended clearances.
7.2.5 Substations
7.2.5.1 General
Substations shall contain all the equipment required for the safe and secure distribution of electricity
to a predetermined area, plant or region, such as H.V./M.V. and L.V. switchgear and control gear
installations, transformers and the pertaining auxiliary facilities.
The substation shall be located in non-hazardous areas and preferably near the center of the load
they are required to supply.
The location of the substations shall also be such that interference between H.V./M.V./L.V. cables,
instrument cables and other services, e.g. pipelines is minimized.
In exceptional cases e.g. in view of restricted space on offshore platforms, electrical substations
may be located in hazardous areas classified as zone 2, subject to approval by the principle. The
following requirements shall apply:
The interior of the building shall be pressurized in accordance with IEC 60079-13;
An over pressure of at least 50Pa (0.5 bar) shall be maintained, using a duplicate fan system with a
suitable dry element dust filtering system to ensure a supply of clean air, each fan being capable of
supplying the required pressure;
The fan system shall be suitable for a Zone 1 area and shall be supplied from tow independent
sources of electricity supply;
Both fans shall normally be in operation and shall have individual alarms to indicate failure in a
manned control center;
7.2.5.2 Outdoor substations

H.V. outdoor open terminal switchgear installations should be designed to Internationally accepted
standards, such as. BS 7354, and shall allow unrestricted walking access to the whole site.
68
Feb. 2012
IPS-E-EL-100(1)
Open terminal outdoor substations should be sited at least 100 m from process unit battery limits. If
this separation is not feasible, switchgear shall be and installed in an indoor substation.
Note 1:
Outdoor switchgear shall be treated as sparking equipment, and the minimum distance from
the process unit should be determined from the analysis of gas cloud behavior by the
process engineering department.
The installation of all components shall be coordinated in accordance with IEC 60071.
The installation class and creepage distance of the isolators shall be selected in accordance with
the expected pollution rate and the likelihood of reduced possibility of maintenance. If not further
specified, a minimum creepage distance of 40 mm/KV shall be applied for insulators.
Note 2:
For further guidance refer to IEC 60815, and if necessary, consult with the local public utility.
Busbars and the connections to the equipments shall be made of copper aluminum tubes or
aluminum conductors. Bi-metallic connectors shall be used at joints between dissimilar metals.
Equipment support structures and line portals shall be of hot-dip galvanized steel and shall have
integral climbing facilities for repair and cleaning purposes.
A 2.4 m high, un climbable perimeter fence with (pad) lockable access gates shall be provided, but
no internal fencing, e.g. around transformers, is required, provided the ground and safety the
clearances stated in the above mentioned standards are satisfied.
Control and auxiliary cables shall be installed in hard covered, pre-cast concrete cable trenches the
top of which shall be surrounding ground level. The trenches shall be well drained and not stand
filled.
Note 3:
All supporting structures and equipments shall be earthed to the substation earthing
system.
The perimeter fence shall be earthed at regular intervals (maximum 30 m) by means of earth
electrodes directly connected to it.
Note 4:
The perimeter fence shall not be connected to the substation earth so as to avoid the danger
of touch voltage.
protection against lightning strikes shall be provided by means of over head earth wires
The substation equipments shall be protected against lightning and switching over voltages by
lightning arrestors.
Control, protection and auxiliary power supply equipments associated with outdoor switchgear shall
be installed in a building which shall comply with the relevant requirements of (7.3). This substation
building, if suitably sub-divided, could also accommodate other switchgear and controlgear at lower
voltages.
69
Feb. 2012
IPS-E-EL-100(1)
7.2.5.3 Indoor substations
7.2.5.3.1 Switchrooms in indoor substations

Onshore, indoor substations shall be single story switchrooms with cable gallery unless otherwise
specified by company representative.
HV. / M.V. and LV. switchgear shall be located in a separate room unless otherwise specified by
company representative. Each switchroom shall have two door which shall lead directly to the
outside from each switch room, and a personnel doors which may connect adjacent rooms.
If electrical equipment is installed on the roof of the substation e.g. air conditioning
compressor/condensers, a cage ladder shall be provided from an entrance platform.
In the cable vault underneath the substation cable tray/racks shall be installed for all cables to the
switchgear and for all interconnecting auxiliary cables between switchgears, panels, etc. For the
power cables to the switchgear vertical cable supports shall be installed.
All cable entry holes in the substation floor or walls shall be suitably sealed. Where such cable entry
holes are required to be gas tight and/or fire resistant, silicon foam or chemical compound with
subliming heat resistant and fire retardant properties shall be used.
Substation lighting and small power installations shall comply with section 7.10
To provide the required environmental conditions, the electrical substations and switch houses shall
be complete with heating, ventilation and/or air conditioning systems
When air conditioning is provided to cool and dry the substation air in relation to the outside air,
provisions shall be made to avoid warm, humid outside air entering directly on to electrical
equipment, causing condensation.
A smoke detection system comprising point detectors shall be installed in the substation. A common
alarm shall be routed from each substation direct to the plant's central fire and gas alarm system i.e.
independent of the substation alarm annunciator.
At least one hand held extinguisher shall be provided near each door.
Note:
The separate room shall be considered for MV. Capacitor bank.
7.2.5.3.2 Switchgear in plant rooms

In the context of this clause a plant room is a room in a building other than a substation, e.g. an
administration building, workshop, etc. which contains service and equipment for that building, e.g.
HVAC plant.
In general only L.V. switchboards and, where required, associated indoor transformers shall be
installed in these rooms in accordance with (7.3.1),but subject to the following additional
requirements.
The switchboard shall be installed back to the wall with 1m free space at rear and at least 2.5m free
space in front for safe operational and maintenance access. 2m free space shall be considered in
both sides for future extension.
Service lines, e.g. fuel, water and air lines shall not be routed over the switchgear, Fuel and water
lines shall be positioned at least 2 m clear of it.
7.2.5.3.3 Battery installation and battery rooms

A separate battery room shall be provided in the substation and have an access door from outside
the substation.
70
Feb. 2012
IPS-E-EL-100(1)
The battery room shall be designed to contain the battery bank only. The size of the room shall be
adequate to allow access to at least three sides of each battery bank for maintenance purposes.
The doors shall be lockable and fitted with an internal panic bolt. The ceiling shall be flat. A water
tap, eye wash basin, sink and drain shall be installed in the room.
All non current carrying metalwork in the room, e.g. cable tray, battery stands etc. shall be bonded
to earth. All metalwork shall be protected against corrosion.
Heating, ventilation and/or air condition of battery rooms shall be included in the HVAC system of
the building.
Exhaust fan motors shall have type of protection 'e' or 'd', gas group C, exhausting to the outside of
the battery room.
The luminaries and convenience outlets shall be suitable for Zone 1, gas group C.
Flexible cables to the batteries may be installed provided they are the EPR or H07 RN-F type or
equivalent.
Smoke and hydrogen detectors shall be considered for battery rooms with alarm indication in
control room.
7.2.6 General design requirements for switchgear rooms
7.2.6.1 Switchgear room floor level shall be at least 1 meter above surrounding ground level.
7.2.6.2 Switchgear room floor shall be made from first-grade trazootile.

7.2.6.3 The width of switchgear room trench shall be proportional to the depth of panels to make
possible the entry of control cables from the front of panels and power cables from rear and bottom
of the panels.
7.2.6.4 The following electrical signals shall be provided in plants control room:
- Main incoming status
- 24v & 110v dc battery chargers failures
- Generator status (off, running)
- 3.3kV & 11kV motor's running status
7.2.6.5 Emergency lighting , self-contained, with a back-up time of 4 hours , shall be provided in all
switchgear rooms in sufficient numbers to provide at least 100 lumen/m2 (lux).
7.2.6.6 Remote control panel (Rcp) shall also accommodate mimic diagrams on its front door.
7.2.6.7 The following accommodations shall be provided in switchgear room:
- Metal cabinets for storage of switchgear's documents, drawings, manuals, etc.
- Etal cabinet for storage of switchgear's accessories such as operating handles, control adaptors,
tools , etc.
- Office desk and chairs :
1 no office desk & 4 nos. chairs
- Telephone & wall clock
7.2.7 Package substations

Package substations may be used for temporary or permanent installations.
Temporary package substations should be used for temporary construction supplies and comprise
LV distribution boards and, optionally, transformers and HV ring main switchgear.
71
Feb. 2012
IPS-E-EL-100(1)
Package substations shall be supplied as complete factory assembled and tested transportable
units.
The HV switchgear, transformer and LV switchgear shall be located in separate compartments,
each accessible from the outside by lockable doors. Sufficient space shall be available in the
compartments to terminate cables and operate the switchgear safely. The switchgear
compartments shall be at least protected to IP 55. The transformer compartment of oil filled
transformer shall be equipped with a leak-proof oil contaminant area.
Note:
Dry type transformers may be mounted on site with the LV switchgear or in a separately
fenced enclosure in the LV switchgear compartment.
Heating, ventilation and/or air-conditioning provisions shall be made in the substation as appropriate
and as necessary to ensure that specified operating temperature limits of the installed equipment
are not exceeded.
Each compartment shall be provided with luminaries and convenience outlets of the weatherproof
industrial type.
7.3 Transformers
7.3.1 General
7.3.1.1 Scope
7.3.1.1.1 This part (transformers) of IPS-E-EL-100(1) specifies general requirements for

engineering considerations , selection and sizing of power and distribution transformers , reactors
and earthing transformers with highest voltage (U m )up to and including 72 kV (acc. to IEC 60076-3).
If there is no specific IPS standard for transformers with voltages above 72 kV , this part should be
applied as minimum .
7.3.1.1.2 Types of transformers included are dry type & oil immersed (hermetically sealed and
conservator type). Exclusions are:
i) single phase transformers rated less than 1 KVA .
ii) polyphase transformers rated less than 5 KVA .
iii) voltage and current transformers.
iv) transformers for static convertors.
v) starting transformers.
vi) testing, welding & traction transformers .
Note 1:
Dry type transformers shall comply with the requirements of IPS-M-EL-151(1).
Note 2:
Oil immersed transformers shall comply with the requirements of IPS-M-EL-152(1).
72
IPS-E-EL-100(1)
Feb. 2012
7.3.1.2 Electrical conditions

i) The system supply voltage variation will be 10% rated value.
ii) The system frequency variation will be 5% rated value.
iii) System fault level at transformer primary terminal.
7.3.1.3 Method of cooling
7.3.1.3.1 Transformers are identified according to cooling method employed . Letter symbols used
in conjunction with cooling are given in Table 7.
TABLE 7- LETTER SYMBOLS FOR COOLING

KIND OF COOLING MEDIUM
SYMBOL
Mineral oil or equivalent flammable synthetic insulating liquid

Non-flammable synthetic insulating liquid
Gas
Water
Air
O
L
G
W
A
KIND OF CIRCULATION
SYMBOL
Natural
Forced (oil not directed)
Forced ( directed oil)
N
F
D
7.3.1.3.2 Transformers shall be identified by four symbols for each cooling method for which a
rating is assigned by the manufacturer .
7.3.1.3.3 Dry-type transformers without protective enclosures are identified by two symbols only for
the cooling medium that is in contact with the windings or the surface coating of windings with an
overall coating ( e.g. epoxy resin) .
7.3.1.3.4 The order in which the symbols are used shall be as given in Table 8. Oblique strokes
shall be used to separate the group symbols for different cooling methods .
TABLE 8- ORDER OF SYMBOLS FOR COOLING SYSTEM

1ST LETTER
2ND LETTER
3RD LETTER
4TH LETTER
Indicating the cooling medium that is in

contact with the windings
Indicating the cooling medium that is in

contact with the external cooling system
Kind of cooling
medium
Kind of cooling
medium
Kind of circulation
Kind of circulation
7.3.1.3.5 Examples:
AN: for dry type transformer without a protective enclosure or with a ventilated enclosure and with
natural air cooling.
73
IPS-E-EL-100(1)
Feb. 2012
ANAN: for dry type transformer in a non-ventilated protective enclosure natural air cooling inside
and outside the enclosure.
ONAN/ONAF, ONAN/OFAF: for oil immersed transformers in which the alternatives of natural or
forced cooling with non-directed oil flow are possible .
ODAF: for an oil-immersed transformer with forced-directed oil circulation and forced air circulation.
7.3.1.4 Recommended values of ratings
7.3.1.4.1 Rated power: Transformers shall be continuously rated . The ratings shall be determined
from the series given in table II of IEC60076-1 . Preferred values of rated power for three phase
transformers are:
5 / 6.3 / 8 / 10 / 12.5 / 16 / 20 / 25 / 31.5 / 40 / 50 / 63 / 80 / 100 / 125 / 160 / 200 / 250 / 315 / 400 /
500 / 630 / 800 / 1000 KVA and etc .
7.3.1.4.2 Rated voltage: The rated voltages of transformer windings shall be selected from IEC
60038 . The followings are most commonly used voltages in oil industries:
230 v / 400 v / 3.3 kV / 6 or 6.6 kV / 10 or 11 kV / 20 kV / 33 kV / 63 or 66 kV .
7.3.1.4.3 Rated ratios : The rated ratio is defined as ratio of primary to secondary voltage at full
load & 0.85 lagging power factor with principal tapping. the most common voltage ratios are in
Table 9.
TABLE 9 - COMMON RATED RATIOS
PRIMARY VOLTAGE
(KV)
3.3 / 6 or 6.6 / 10 or 11 / 20 / 33
10 or 11 / 20 / 33 / 63 or 66
10 or 11 / 20 / 33 / 63 or 66
20 / 33 / 63 or 66
33 / 63 or 66
63 or 66
SECONDARY VOLTAGE
(KV)
0.4
3.3
6 or 6.6
10 or 11
20
33
7.3.1.4.4 Rated impedance voltage: Unless a specific transformer impedance voltage is required,
the values shall be chosen from typical values given in Table I of IEC60076-5 (table 10). The
impedance voltage shall be that applicable to principal tapping and rated current. Typical values of
impedance voltage for transformers with two windings are as follows:
TABLE 10 - COMMON RATED IMPEDANCE VOLTAGES

RATED POWER
( KVA )
Up to 630
631 to 1250
1251 to 3150
3151 to 6300
6301 to 12500
12501 to 25000
IMPEDANCE VOLTAGE
(%)
4.0
5.0
6.25
7.15
8.35
10.0
7.3.1.4.5 Rated short circuit capacity: The short circuit withstands ability of transformers and
reactors will be in accordance with IEC 60076-5. If the short circuit apparent power of the system is
greater than those given in Table II of IEC 60076-5 (table 11), the manufacturer shall be informed.
Short circuit apparent powers of the systems which may be used in absence of specification are as
follows:
74
IPS-E-EL-100(1)
Feb. 2012
TABLE 11 - COMMON RATED SHORT CIRCUIT APPARENT POWER

HIGHEST SYSTEM
VOLTAGE (KV)
SHORT CIRCUIT APPARENT

POWER (MVA)
3.3
7.2 / 12 / 17.5 / 24
36
52 / 72.5
150
500
1500
2500
7.3.2 Transformer sizing

7.3.2.1 Power & distribution transformers
The rated power of a transformer is decided on the basis of the maximum active power demand
determined in the course of project planning by applying the expected power factor.
Note:
A reserve of power for the expected yearly rate of increase of power (KVA) must be
considered if required.
A schedule based on the plant design capacity of the installed electrical loads shall be prepared. In
this electrical load list , loads are determined as continuous, intermittent and standby.
7.3.2.1.1 First step is to find peak load value in kW's & KVAR 's .
If :
A = Sum of all continuously operating loads.
B = Sum of all intermittent loads.
C = Sum of all standby loads.
Then :
Maximum normal running load = X A +Y B
Peak load = X A + Max {Y B, largest intermittent load} + Max {Z C, largest standby load}
X, Y, Z are diversity factors determined by principal.
The following default values for X, Y, Z could be used for initial load assessments or if diversity
factors have not been finalized.
X = 100%
Y = 75%
Z = 10%
7.3.2.1.2 After calculating peak load value, maximum load KVA is determined by using total power
factor (or using total KVAR value).
Peak load (kW)
Maximum load ( KVA ) =
Total power factor
or
Maximum load ( KVA ) = peak load ( kw ) + peak load ( KVAR )
2
7.3.2.1.3 The required KVA is determined by multiplying maximum load KVA by 120% for
possibility of future expansion . Since the value of required KVA is not normally the same as a
standard value , the transformer KVA will be the nearest standard transformer rating above the
required KVA .
7.3.2.1.4 The required transformer KVA may be increased by load flow & motor starting studies
due to voltage drop calculations .For the starting study , the greatest electric motor should be
considered with other normal loads connected .
75
Feb. 2012
IPS-E-EL-100(1)
Note 1:
The percentage of total intermittent load that contribute to the normal running load will
depend on plant operation .
Note 2:
The second term in peak load formula is the biggest value between Y B
individual intermittent load.
and largest
Note 3:
The third term in peak load formula is the biggest value between Z C and largest individual
standby load.
Note 4:
Transformers shall be rated for maximum ambient temperature.
Note 5:
Maximum rating of transformers feeding plant substations should be such that the rated
current of their secondary winding does not exceed 2000 A when feeding an MV
switchboard, or 2500 A when feeding an LV switchboard . This results in the following
maximum ratings:
1600 KVA if feeding LV switchboard.
10 MVA if feeding MV 3.3 KV switchboard.
20 MVA if feeding MV 6 or 6.6 KV switchboard.
40 MVA if feeding MV 10 or 11 KV switchboard.
Note 6:
Higher ratings should be considered only if a significant cost saving can be proven.
7.3.2.2 Motor unit transformers

Motor unit transformers with double wound, core- type, oil immersed, ONAN cooled, sealed, are
used normally to avoid the installation of a switchboard with different voltage. For example when we
have a 10 (or 11) kV switchboard and a single motor with voltage rating of 3.3 kV .
7.3.2.2.1 The unit transformer shall be specifically designed and used exclusively for supplying the
3.3 kV induction motor arranged for direct-on-line starting from the associated 10 (or 11) kV feeder
circuit breaker.
Note:
Using of unit transformers shall be decided based on economical considerations.
7.3.2.2.2 Two main requirements for unit transformers are:
76
Feb. 2012
IPS-E-EL-100(1)
i) The unit transformer shall be capable of withstanding full voltage motor starting current for 15
seconds unless otherwise specified.
ii) The voltage drop at the motor terminals at startup shall not exceed 15%.
7.3.3 Transformer selection
7.3.3.1 Rated values

Rated values of transformers such as power, voltage, ratio, impedance voltage & short circuit
capacity are selected from recommended values of ratings in section 7.3.1.
7.3.3.2 Type of transformers
7.3.3.2.1 Oil immersed transformers: oil immersed transformers or reactors shall either be of the
sealed tank type or conservator type. The advantages of sealed tank design are their almost
maintenance-free operation and with certain designs there is a space saving because of the
absence of external pipe work.
Transformers for outdoor use and rated up to and including 2500 KVA shall be of the oil-filled
hermetically sealed type .Transformers above 2500 KVA should be conservator type .
Note: Using of sealed type transformers above 2500 KVA shall be decided by company
representative.
7.3.3.2.2 Dry-type transformers: In locations where fire risk must be minimized e.g. in public and
residential buildings, on offshore platforms etc., dry-type transformer having cast resin encapsulated
windings can be used. Cast resin encapsulated transformers are recognized as almost notcombustible, self-extinguishing and electrically unaffected by high humidity. They shall be used for
ratings up to and including 1250 KVA with secondary voltage 400/230 v.
7.3.3.3 Vector group

Where there are no restriction due to parallel operation with other / existing transformers of different
winding connection, step-down transformers shall be specified with Dyn5 or Dyn11 in accordance
with IEC60076-4. Any other vector group should be subjected to agreement.
7.3.3.4 Voltage tappings

Unless otherwise specified the higher voltage winding of all transformers should be provided with
tappings for constant KVA to compensate variations in the supply voltage.
7.3.3.4.1 Off-circuit tap changer: Unless otherwise specified all transformers should have an offcircuit tap changer with a principal and four additional tappings. Tapping range shall be 5% in four
equal steps of 2.5% of the nominal primary voltage.
7.3.3.4.2 On-load tap changer: Main incoming supply transformers receiving power from public
utility and rated 5 MVA and above with primary rated voltages equal or above 36 kV are usually
fitted with on-load tap changers. There is no need for on-load tap changer if voltage variation range
is less than 5%. Transformers at the end of long transmission lines (normally longer than 50 km)
may need to have on-load tap changer. Maximum voltage variation at transformer location shall be
calculated in project specification stage (engineering studies).
77
Feb. 2012
IPS-E-EL-100(1)
7.3.3.4.3 The use of on-load tap changers fitted to site distribution transformers shall be permitted
only if it is anticipated that plant non-transient voltage variations of greater than 6% could occur as
a result of normal process operations and also that there would be process disruption if a
transformer was switched out of circuit to alter the tapping out.
7.3.3.4.4 Tapping range and tap steps : On-load tap changers should have a minimum tapping
range of 7.5% in 13 taps with 12 tap steps of 1.25%, unless voltage variations dictate a wider
range and more steps. Generally tapping range shall be at least 120% of anticipated/calculated
voltage variation.
Note 1:
On-load tap changers shall be of automatic voltage control type. They shall also be manually
operated either at the transformer or from a remote control location in substation or control
room.
Note 2:
The high speed resistance type of on-load tap changer is preferred.
Note 3:
Where on-load tap changers are required , they shall comply with IEC60214 & IEC60542.
Note 4:
Tapping range and tap steps are normally determined by transformer manufacturer
according to voltage variation, rated power and rated system voltage.
Note 5:
On-load tap changers are not normally required on generator step-up transformers.
Note 6:
Reactors shall not be fitted with on-load tap changer and earthing transformers shall not be
fitted with any type of tap changer .
7.3.3.5 Type of transformer cooling

The type of cooling specified for transformers less than 15 MVA can be ONAN. This requires no
particular maintenance and is not subjected to any exterior construction such as auxiliary power
source, thermostat, relays, fans, pumps, etc.
7.3.3.5.1 If an economic case can be made for forced cooling or provision for forced cooling, the
first level is ONAF and the second is OFAF. When a combination of cooling methods is specified
(ONAN/ONAF or ONAN/OFAF) the transformer shall be capable of continuous operation with
ONAN cooling at the specified output KVA rating.
7.3.3.5.2 Forced cooling or provision for forced cooling may be considered under the following
circumstances:
i) It is anticipated that there could be a future plant load increase .
ii) Transformers for use on a triple radial system could under certain operating conditions
experience higher than normal rated loads.
78
Feb. 2012
IPS-E-EL-100(1)
iii) A unit which usually runs as a base load has occasional periods of high load demand that would
be outside the normal cyclic loading capabilities of the transformer or reactor.
Note 1:
Any requirement for forced cooling, and whether this is to be fitted at the time of initial
purchase or to be added at a later date, shall be as specified in data sheet .
Note 2:
If provision for forced cooling is specified, the manufacturer shall allow for this in the
transformer design.
7.3.4 More design and engineering considerations
7.3.4.1 Effect of altitude on transformers
7.3.4.1.1 Effect of altitude on transformer temperature rise: The effect of the decreased air
density due to high altitude is to increase the temperature rise of transformers which are dependant
upon air for dissipation of heat losses. For a naturally cooled transformer ( . . AN ), the limit of
C
average winding temperature rise shall be reduced by 1 for every interval of 400 m by which the
installations altitude exceed 1000 m. For a forced cooled transformer ( . . AF ) , the reduction shall
C
be 1 for every 250 m .
7.3.4.1.2 Rated operation at high altitude: Transformers can be operated at rated KVA at
altitudes greater than 1000 m without exceeding temperature limits provided the average
temperature of cooling air does not exceed the value of Table 12 for the respective altitude .
Note:
It is recommended that the average temperature of cooling air be calculated by averaging 24
consecutive hourly readings . When the outdoor air is the cooling medium , the average of
maximum and minimum daily temperatures may be used .
79
IPS-E-EL-100(1)
Feb. 2012
TABLE 12 - MAXIMUM ALLOWABLE AVERAGE TEMPERATURE OF COOLING AIR ( C )

(According to IEC-60072-2)
METHOD OF COOLING
1000 m
2000 m
3000 m
4000 m
Oil-immersed self-cooled
Oil-immersed forced-air-cooled
30
30
28
26
25
23
23
20
30
30
30
27
26
22
24
22
15
21
18
7
30
30
30
24
22
15
19
14
0
14
6
-15
Dry-type self-cooled
1 ) 55 C rise
2 ) 80 C rise
3 ) 150 C rise
Dry-type forced-air-cooled
1 ) 55 C rise
2 ) 80 C rise
3 ) 150 C rise
7.3.4.1.3 Operation at less than rated KVA at high altitude: Transformers can be operated at
altitudes greater than 1000 m without exceeding temperature limits provided the load to be carried
is reduced to below ratings by the percentages given in Table 13 for each 100 meters that the
altitude is above 1000 m.
TABLE 13 - KVA CORRECTION FACTOR FOR EACH 100 METERS

FOR ALTITUDES GREATER THAN 1000 METERS
(According to IEC-60072-2)
TYPE OF COOLING
CORRECTION FACTOR
( PERCENT )
Oil-immersed self-cooled
0.4
Oil-immersed forced-air-cooled
0.5
Dry-type self-cooled
0.3
Dry-type forced-air-cooled
0.5
7.3.4.2 Parallel operation of transformers
7.3.4.2.1 Parallel operation means direct terminal-to-terminal connection between transformers in

the same installation . For successful parallel operation , the transformers require:
i) The same vector group .
ii) The same ratio with same tolerance and similar tapping range .
iii) Approximately the same impedance voltage (maximum permissible discrepancies 10% ) .
iv) Approximately the same rated output KVA (not more than 1 : 2 ) .
80
IPS-E-EL-100(1)
Feb. 2012
Note:
Transformers built according to different design concepts are likely to present different
impedance level and different variation trends across the tapping range.
7.3.4.2.2 Effect of unequal impedance voltages in parallel operation of transformers: When

transformers with unequal impedance voltages are connected in parallel , the transformer with lower
impedance voltage value will take up a higher percentage of its rated power . So that the absolute
voltage drop will be the same for both transformers . This may cause marginally increased
combined power loss for the transformation and may restrict the load ability of the installation .
In such a case to prevent the transformer with lower impedance voltage from overloading , the total
power of installation should be calculated by equation as bellow :
U ka
R
S = S ra +
R
S rb
U kb
R
Where
S : Total power ( KVA )
S ra : Rated power of transformer with lower impedance voltage (U ka )
S rb : Rated power of transformer with higher impedance voltage ( U kb )
R
7.3.4.3 Earthing transformers
7.3.4.3.1 Earthing transformers are three phase transformers (or reactors ) used to provide an
artificial loading neutral for earthing of a system at a point where it is otherwise un-earthed.
Connecting to earth can be done directly or through an earthing resistor.
Earthing transformers are usually connected either in zigzag or star/delta. A delta connected
winding may be of the open type to adjust the zero- sequence impedance.
Note :
Earthing transformers may be specified with a low voltage winding having a continuous
rated power for substation auxiliary supply .
Ratings :
7.3.4.3.2 Rated voltage of the main winding: Unless operating conditions justify the selection of a
higher value, the rated voltage shall be equal to the line voltage of the associated system .
7.3.4.3.3 Rated neutral current: The rated neutral current shall be specified to be not less than the
highest value of continuous current under service conditions , for example phase unbalance.
7.3.4.3.4 Rated zero-sequence impedance: The value of zero-sequence impedance may either
be let open in the specification or be specified. (for example when the earthing transformer itself is
used to limit the earth fault current)
81
Feb. 2012
IPS-E-EL-100(1)
Note:
Earthing transformers shall be designed to withstand without damage the thermal and
dynamic effects of the rated current.
7.3.4.4 Reactors
According to IEC60289, there are approximately eight different types of reactors. The most
important type that may be used in NIOC fields is as follows:
7.3.4.4.1 Current limiting reactors: The reactors intended for limiting the short-time current under
system fault conditions or starting of AC motors. During normal operation a continuous current flows
through the current limiting reactor.
Ratings:
7.3.4.4.2 Rated continuous current: Unless otherwise specified, the rated continuous current is a
symmetrical three- phase current. Preferred values of the rated continuous current shall correspond
to the series R10 in ISO standard 3.
7.3.4.4.3 Rated short-time current: The rated short-time current shall be specified to be not less
than the highest value of current under recognized fault or starting conditions.
7.3.4.4.4 Rated short-time current duration: Unless otherwise specified, the rated short-time
current duration shall be 2 seconds for current-limiting reactors.
7.3.4.4.5 Rated impedance: The value of rated impedance shall be specified together with the
rated short-time current in accordance with the system parameters and the recognized case of
system faults.
Note:
Current limiting reactors shall be designed to withstand the thermal and dynamic effects of
the rated short-time current for its rated duration.
7.3.4.5 Neutral grounding resistor (NGR)

Power transformers with secondary voltage of 11 KV, 6 KV or 3 KV which supply electric motors,
shall be equipped with suitable NGRs. The time rating of the NGR shall be 10 second. The current
rating shall be calculated by designer.
7.4 Electrical motors
7.4.1 General
Electrical motors are one of the most important components in oil , gas and petrochemical plants.
The following general requirements shall be considered in design and selection of the rotating
electric machines.
7.4.1.1 All the electrical motors shall be designed for the load characteristics and operational duty of
the driven equipment.
82
Feb. 2012
IPS-E-EL-100(1)
7.4.1.2 All the electrical motors and their accessories shall comply with sound engineering practices
to have an expected lifetime of minimum 20 years. (Excepting rolling element bearings).
7.4.1.3 Unless there is a clear technical/economic justification for preferring a synchronous motor
over an induction motor, the squirrel cage induction motor generally would be recommended.
7.4.1.4 Synchronous motors generally should not be considered at ratings below 2 MW.
7.4.1.5 Synchronous motors shall be brush-less and the exciter shall consist of a brush-less three
phase synchronous generator, rotating rectifier , a pilot exciter if applicable ,field protection and
shorting functions shall be accomplished by solid state control.
7.4.1.6 For synchronous motors, the excitation system shall be equipped with an automatic power
factor controller to maintain the set power factor within a margin of +-2.5% .
7.4.1.7 The DC motors could be used for special application such as fans, blenders , drilling mud
pumps &seal or lube auxiliary pumps and etc .
7.4.1.8 The application of the VFD (variable frequency drive) systems shall be considered where it
can be justified that the VFD system will benefit the operation, maintenance and efficiency of the
plant. A technical /economical study regarding the above shall be performed and submitted to
company engineer for approval.
7.4.2 Service condition
7.4.2.1 The motors will be generally installed outdoor in areas where the presence of flammable gas
or vapor is foreseen. In case where the motor will be installed indoor, it will be indicated in data
sheet.
7.4.2.2 The electrical motor shall meet the requirements of the classified areas as specified in this
specification and indicated in data sheet.
7.4.3 Voltages and output ratings
7.4.3.1 The voltage levels adapted in the oil, gas and petrochemical industries of Iran are based on
the IEC recommendation No 60038 and part 6.1.5.1 of this standard.
7.4.3.2 The low voltage system is generally 400/230 volt with solidly earthed neutral.
7.4.3.3 The voltage of the motors rated up to 0.4 kW can be selected as 230 volt single phase and
neutral. If capacitor type single phase motor is used, the capacitor shall be metal clad with paper
dielectric. Motors for critical services such as compressor auxiliaries, lube oil systems, special
pumps, etc. shall be 400 volts, 3 phase.
7.4.3.4 The voltage of the motors 0.4 kW up to 150 kW shall be 400 volt three phase. The voltage of
150 kW motors can be selected as 400, 3300 or 6000 volt depending upon the availability of such
voltage levels.
7.43.5 For special applications or existing facilities, other voltages may be specified. The nominal
voltage of the motor will be indicated in data sheet.
7.4.3.6 The voltage of the motors rated 150 kW to 1000 kW shall be 3.3 KV or 6 kV.
7.4.3.7 The voltage of the motors above 1000 kW can be selected as 6 kV or 10 kV or 11 KV
based on technical and economical considerations of the electrical power supply system, in
particular the voltage drop during starting of the motor.
7.4.3.8 All rotating machines shall be capable of operating continuously at rated torque at any
frequency between -2% and +2% of the nominal frequency together with a voltage variation of
5%. The nominal frequency is 50Hz.
83
Feb. 2012
IPS-E-EL-100(1)
7.4.3.9 The motors shall be capable of performing its primary functions at voltage variation of 10%
and frequency variation of 5% according to IEC 60034-1. For generator and synchronous motor
voltage variation shall be considered as 8%.
7.4.4 Motor sizing
7.4.4.1 Frame sizes and dimensions and the kW ratings of the motors shall be in accordance with
IEC 60072-1.
7.4.4.2 Motors shall be sized, taking into consideration the appropriate multiplying factor/s related to
each type and size of the driven equipment. The size of the motors versus the driven equipment
shall be according to the recommendations of the driven equipment specifications.
7.4.5 Motor starting
7.4.5.1 Motors shall be suitable for Direct On Line Starting.

7.4.5.2 Upon the approval of company representative, star-delta or auto-transformer starting may
be employed for 400 volt motors if required .
7.4.5.3 For motors rated up to 150 kW the maximum value of locked rotor apparent power shall
comply with IEC 60034-12.
7.4.5.4 For motors rated above 150 kW , the starting current shall not exceed 6 times the rated
current of the motor . A load flow study regarding starting of biggest electric motor shall be
performed and any limitation in starting current of the motors shall be specified in relevant data
sheets.
7.4.5.5 The motor design shall allow without injurious heating of insulated windings, at least three
successive starts from cold against full load torque and two successive starts with the motor initially
at full load operating temperature.
7.4.5.6 For high voltage motors individual dedicated unit transformer directly connected to the motor
may be used, which shall be shown on single line diagram/s.The transformer shall withstand the
thermal and dynamic stresses during repeated direct on line starting of the motors.
7.4.5.7 Motors rated 150 kW to 1000 kW shall be controlled by vacuum type contactors. Motors
rated above 1000 kW shall be controlled by vacuum type circuit breakers. The motors shall be
designed to withstand the switching surges of vacuum interrupters.
7.4.5.8 The starting performance and pull up torque of the motor shall be coordinated with the
driven equipment supplier.
7.4.5.9 Motors shall be able to overcome starting load inertia as well as accelerating the load to
rated speed, when the applied voltage is 80% of the nominal voltage.
7.4.5.10 In case of power interruption during operation, the motor may be reconnected to the supply
voltage at any time. The residual voltage magnitude and phase angle shall not have any detrimental
effect on the motor.
7.5 Electrical Protection, Metering & Control
7.5.1 General
7.5.1.1 This section specifies those items which apply generally to the selection and application of
protective relays witch are supplied to provide electrical power system protection for National
84
Feb. 2012
IPS-E-EL-100(1)
Iranian Oil Company installation.Importance , voltage level and cost are the considerations in
selection of protection systems.
7.5.1.2 Protective relays requirements

i) All protective relays shall be microprocessor based.single function relays( such as thermal
overload ,earth lekage relays for low voltage system) may be statics or electromagnetic type by
approval of company representative. Relays for incomers and bus couplers (HV., MV., and LV.)
shall be flush mounted. All facilities such as softwares, links, ports and test sockets for
communication, networking and cofiguration shall be considered for microprocessor relays. This
relays shall have data and disturbance recording facilities.
ii) Unless otherwise specified by the principle the overcurrent and earth fault protective relays shall
have Inverse Definite Minimum Time ( I.D.M.T.) characteristics of the standard types A, B & C in
accordance with I.E.C.60255-4.
7.5.1.3 Selectivity and co-ordination

i) The automatic protective systems shall be designed to achieve selective isolation of faulted
equipments with minimum delay. In many events this shall be within a time corresponding to the
short circuit current withstand capability of the equipment ,system stability limits and the maximum
fault clearance times.
ii) Adequate and selective phase short circuit and earth fault protection shall be provided based on
the magnitude of short circuit currents and method of system earthing.
The short circuit currents calculation for this propose shall be based on IEC 60909-1, 60909-2, and
6090-3.
iii) Protective relay system shall be selective and the settings shall be coordinated such that back
up protection is provided to initiate fault clearance in the event of protective system and/or switching
device failure.
7.5.1.4 Additional requirements

i) Limited duration overcurrent arising from single or group motor starting/ reacceleration shall be
permitted.
ii) Automatic control systems such as load transfer, motor restarting arrangements and protective
system to initiate load shedding shall be incorporated to affect plant operations as little as
practicable and economically justifiable after system or equipment failures.
iii) Protective relay settings shall be based on a study of fault conditions for which the protective
system has been incorporated.
A protection and metering diagram in the form of single line diagram shall be prepared for the
complete electrical system to indicate the type and location of all metering and protective devices
and associated instrument transformers to be provided. In addition to this single line diagram a
tabulated relay settings and coordinated relay and fuse characteristics etc. plotted in graphical form
shall be included.
7.5.2 Main incomer and feeder protection
7.5.2.1 Main incomer
7.5.2.1.1 Single or more non parallel incomers supplied from public utility and no on-site generation
i) Phase fault overcurrent protection (50,51)
85
Feb. 2012
IPS-E-EL-100(1)
ii) Earth fault overcurrent protection (50N,51N)

iii) Under voltage and phase sequence voltage protection (27,47)
iv) Breker failure protection (50BF)
Note:
For outdoor substation busbar protection is an option.
7.5.2.1.2 Parallel incomers supplied from public utility and no on-site generation the protection
requirement shall be as described in 7.5.2.1.1 with the addition of directional overcurrent and
directional earth fault protection for each incomer.
Note:
If unit feeder protection is considered ,directional protection relays may not be required.
7.5.2.1.3 Public utility supply in parallel with onsite generation

Where the on-site generation is normally or frequently parallel with public utility supply the
protection requirements appropriate to 7.5.3. shall be supplemented by means for detecting and
clearing external public utility faults to permit uninterrupted operation minimum down time of the site
power system. The additional protection shall be as follows:
i) Directional overcurrent and directional earth fault protection (67, 67N).
ii) Sensitive reverse power protection (32).
iii) Frequency relay with a time definite relay (81).
Definite time undervoltage relay (27).
Synchronizing check relay (25) - would be decided by company representative.
Items (ii),(iii) and (iv) shall be arrange such that during a reverse power(export) condition, tripping of
main incomers does not occur unless there is a simultaneous under frequency (iii) or under voltage
(iv) condition. The tripping times shall be determined from stability studies.
7.5.2.2 Feeder protection
7.5.2.2.1 Cables or very short over head lines(less than 5 K.m.) without load end switchgear
For the cables and overhead lines directly connected to plant such as transformers without
switchgear at load end the following protections shall be considered:
i) Phase fault overcurrent protection (50,51).
ii) Earthfault protection (50N,51N).
The protection installed at source end shall be comprised both cables / overhead lines and also
load end.
7.5.2.2.2 Cables or very short over head lines(less than 5 K.m.)with switchgear at both ends
In addition to the above protections, differential protection shall be provided on all 3.3,6,11,20,33,66
K.V. feeders where:
i) Feeders can be operated in parallel.
ii) Short circuit overcurrent and earth fault protection clearance time is required.
86
Feb. 2012
IPS-E-EL-100(1)
Inter tripping with remote end circuit breakers shall be provided on duplicate feeders.
7.5.3 generator protection
7.5.3.1. This subsection specifies the electrical protection requirements for generators. It does not
cover mechanical protective requirements of prime mover/generators.
Note:
The method of connection of a generator to the electrical power system (direct or unit
connection ) dictates the type of neutral earthing and protective relaying requirements.
7.5.3.2 Low voltage generator from 100 KVA up to and include 500 KVA
i) IDMT phase overcurrent protection (50,51)
ii) Earth fault protection (50N,51N)
iii) Undervoltage protection (27)
iv) Over voltage protection (59)
v) Frequency relay (81)
vi) Overload protection (49)
vii) Reverse power relay (32) for generators which may be operated in parallel to gether or with
other power sources.
7.5.3.2.1 All above protections,exept over voltage protection, shall trip the generator breaker
device.Over voltage protection shall also shut down the generator.
7.5.3.3 Low voltage generator above 500 KVA

The protection of this size of generatore shall be as described in 7.5.3.2 and additional protection
shall be as follow :
i) Restricted earth fault relay (64)
ii) Winding temprature monitor protection (49T)
iii) Reverse power relay (32) for generators which may be operated in parallel with other power
sources.
Note:
The current transformers for short circuit protection purpose(phase and earth) should be
placed on neutral point terminal box.
7.5.3.4 Medium voltage generators up to 2 MVA

i) Phase overcurrent protection (50,51)
iii) Differential protection (87G)
iv) Under and over voltage protection (27,59)
v) Frequency protection (81)
vi) Reverse power protection (32)
87
Feb. 2012
IPS-E-EL-100(1)
vii) Overload protection (49)

viii) Winding temperature monitor relay (49T)
ix) Loss of excitation protection (40)
The current transformers for short circuit protection purpose(phase and earth) shall be placed on
neutral point terminal box.
7.5.3.5 Medium voltage generators include and above 2 MVA

The protection of this size of generators shall be as described in 7.5.3.4 and additional protections
shall be as follows:
i) Voltage control overcurrent protection (50V,51V)
ii) Rotor earth fault relay (64R)
iii) Negative phase sequence relay (46)
iv) Field diode failure (above 15 MVA only)
v)
Over exitation relay (24)
vi) Voltage Balance (60)
7.5.3.5.2. Where two or more generators required operate in parallel mode ;synchroscope shall be
used.
7.5.3.6 Trip and alarm orders and facilities

The operation of all protective relay shall trip the C.B. except following alarms:
- Stator winding temperature(first stage)
- Rotor earth fault ( first stage)
- Overload relay (first stage)
- Over Voltage
The following trip commands shall shut down the primmover and trip the C.B.:
- Rotor earth fault (second stage)
- Stator winding temperature (second stage)
- Emergency stop- manual
- Generator differential (87G)
- Short circuit (51)
- Earth fault (50GN)
Any primmover shut down shall trip the circuit breaker.
7.5.4 Power transformer protection
7.5.4.1. This subsection specifies industrial power transformer protection scheme
7.5.4.2. Transformers up to and include 250 KVA

i) Fuse
7.5.4.2.1 The fuse shall not be ruptured under magnetizing inrush condition.
88
IPS-E-EL-100(1)
Feb. 2012
Note:
Fuse is the minimum protection requirement for both primary and secondary sides.
7.5.4.3 Transformers above 250 KVA rating up to and including 2500 KVA (sealed type)
a) Primary side
ii) Earth fault protection
(50N,51N)
iii) Breker failure protection (50BF)
b) Secondary side
iii) Standby earth fault relay (51G) for transformers rating of 500 KVA and above. This relay shall
be of I.D.M.T. type.
iv) Overload relay (49).
v) Oil temperature device with alarm and trip contacts for transformers rating of 500KVA and
above (26).
vi) Resetting
Contacts (63P).
sudden
pressure,
spring
loaded,
relief
device
with
operating
vii) Pressure/vacuum gauge incorporating alarm contacts ().

vii) Oil level indicator with operating contacts (71).
viii) Breaker failure protection (50BF)
7.5.4.3.1 Restricted earth fault protection (64) shall be considered for all M.V/M.V, H.V/M.V
transformers.
7.5.4.3.2 The C.T.s for restricted earth fault protection shall be of class X. The high
impedance scheme employing stabilizing resistor and a voltage operated relay is preferred.
7.5.4.3.3 If transformers of 250 KVA up to2500 KVA rating are conservator type they shall
incorporate Buchholtz relay completed with alarm and trip contacts.
7.5.4.3.4 The Inverse Definite Minimum Time ( I.D.M.T.) overcurrent and earth fault relay's
characteristics shall be of inverse, very inverse ,extremely inverse and definite time to match to old
system protection.
7.5.4.3.5 Either earth fault element of a conventional 3 pole phase and earth relay (2 phase and
1earth fault) or one single pole earth fault relay supplied by a core balance C.T. can be used as
earth fault protection of transformer primary side (i.e. delta winding).
7.5.4.3.6 In the secondary side, where the transformer neutral point earthed solidly or via resistor
the following shall be considered:
i) Where the transformer is solidly earthed, the primary current ratio of current transformer shall be
of power transformer approximate nominal current.
ii) If the transformer is earthed through an impedance, the primary current rating of current
transformer for stand by earth fault protection shall be of earthing resistor current let through.
89
Feb. 2012
IPS-E-EL-100(1)
7.5.4.4 Transformers above 2500 KVA up to 5000 KVA

All protection schemes used for transformers of 250KVA up to 2500 KVA (item 7.5.4.3 except vii)
shall be used for the above transformer category. in addition the following shall be added:
i) Restricted earth fault protection shall be used for all transformers (64).
ii) Buchholtz relay with alarm and trip contacts (63).
iii) Overload protection (49).
iv) Winding temperature device with alarm and trip settings and appropriate Contacts (49T).
7.5.4.5 Transformers of 5000 KVA rating up to 10000 KVA
a) Primary side
i)
Phase fault overcurrent protection (50,51).
ii) Earth fault protection (50N) and ( 50G).

iii) Breker failure protection (50BF)
b) Secondary side
i) Phase fault overcurrent protection (50,51).
ii) Earth fault protection (50N,51N).
iii) Stand by earth fault relay (51G).
v) Restricted earth fault relay (64).
vi) Breker failure protection (50BF)
c) Overall transformer protection

i) Differential protection (87).
ii) Buchholtz relay completed with alarm and trip contacts (63).
iii) Oil temperature relay with alarm and trip contacts (26).
iv) Resetting sudden pressure, spring loaded ,relief device with operating contacts (63P).
v) Oil level indicator with operating contacts (71).
vi) Winding temperature device with alarm and trip settings and appropriate contacts (49T).
7.5.4.5.1 The transformer primary and secondary cables shall be included within the protection of
differential protection scheme.
7.5.4.5.2 Differential protection relay shall be of the biased type to cater the maximum transformer
ratio and shall include an harmonic resistant feature to avoid maloperation due to avoid magnetizing
inrush current.
7.5.4.5.3 C.T.s for differential and restricted protection shall be class X.
7.5.4.5.4 Transformers which their primary and/or secondary sides are connected to overhead lines
shall be equipped with lighting arresters.
7.5.4.6 Transformers of 10000 KVA rating and above

All protection schemes used for transformers of 5000KVA up to 10000 KVA (item 7.5.4.5) shall be
applied to the above transformer rating . in addition, the following shall be added:
i) Winding temperature device with alarm and trip settings and appropriate contacts (49T).
90
Feb. 2012
IPS-E-EL-100(1)
The microprocessor based temperature monitor conjunction with RTDs placed in each winding may
be used.
ii) Over fluxing protection where supply frequency assumed to be varied in large scale(for example
transformers supplied via a local generator) (24).
7.5.4.7 On load tap changer transformers

If transformers are equipped with on load tap changers the following protection shall be added:
i) Buchholtz protection completed with alarm and trip contacts for tap changer or assembly (63).
ii) Automatic voltage regulator relay for changing the transformer tap ().
7.5.4.8 Parallel transformers

Where two transformers normally operated in parallel condition, each feeder shall be supplied by
directional overcurrent and earth fault relays (67) and (67N).The directional protection (67) and
(67N) do not apply for case where the transformers are equipped with transformer differential
protection.
7.5.4.9 Auxiliary relays for transformer mechanical protection

a) The transformer mechanical protection such as Buchholtz, oil temperature, etc. shall have their
own dedicated hand reset flag alarm and tripping relay located on the respective transformer
switchgear.
Where necessary the alarm signals would normally be routed to alarm annunciator within the
substation.
7.5.4.10 Tripping requirements
7.5.4.10.1 Transformer protection trip shall be via dedicated hand reset lock out relays.
7.5.4.10.2 The following trips shall be generally operates the relevant lock out relay.
a) Primary lock out relay:

i) Earth fault relay (50N, 51N)
ii) Instantaneous phase overcurrent relay (50)
iii) Differential protection (87, 87N)
iv) Sudden pressure relief vent device (63P)
v) Breker failure protection (50BF)
b) Secondary lock out relay:

i) Restricted earth fault relay (64)
ii) Non-unit earth fault relay (50N, 51N,50G)
iii) Liquid surges (i.e. Buchholtz trip 63, pressure relief)
iv) Winding temperature trip (49T)
v) Directional overcurrent and earth fault trip (67, 67N)
vi) Stand by earth fault relay (51G)
91
Feb. 2012
IPS-E-EL-100(1)
vii) Breker failure protection (50BF)
7.5.4.10.3. The intertrip send and receive relay shall be located respectively on secondary and
primary switchgears. All protective relays which tripped secondary lock out relay shall energize
send relay and consequently this relay shall send a signal to energize receive relay on primary
switchgear and the latest shall trip the circuit breakers.
7.5.5 Motor protection
7.5.5.1 This subsection specifies induction and synchronous motor protection requierments. The
protection of special motors is not covered.
7.5.5.2 Low voltage motors

Single phase motors up to 400 watts rating shall be provided with:
i) built-in or external thermal over load relay (49).
ii) fuse or MCB.
7.5.5.2.1 Three phase motors between 0.4 KW up to 18.5 KW

i) Fuse or MCCB (will be decided by company representative)
ii) Over load relay (49)
7.5.5.2.2 Motors between 18.5 KW up to 150 KW

i) Fuse
ii) Over load relay (49)
iii) Earth leakage relay (50G)
iv) Time delay under voltage phase sequence relay -27,47- (will be decided by company
representative)
7.5.5.2.2.1 Bimetal over load relay shall be three pole, ambient compensated, incorporating single
phase protection.
7.5.5.2.2.2 The fuse shall be high rupturing type and shall have characteristic class of aM
(According to IEC-60269).
7.5.5.2.2.3 The earth leakage relay shall be supplied by a corbalance current transformer and the
minimum setting of relay shall be started from at least 10% of motor full load current.
7.5.5.2.2.4 Over load relay rating above 72 ampere shall be C.T. operated.
7.5.5.2.2.5 Where using solid state over load relays, these relays shall have facilities to test all
characteristics curves.
7.5.5.3 Medium voltage motors
7.5.5.3.1 motors above 150 KW and up to 1000KW

i) Thermal over load protection (49)
ii) Fuse
92
Feb. 2012
IPS-E-EL-100(1)
iii) Sensetive earth fault protection (50G)

iv) Negative phase sequence protection (46)
v) Under voltage protection (27)
vi) Incomplete sequence protection (48)
vii) Anti restart protection (66)
viii) Locked rotor protection (51L)
ix) Winding temperatour protection (49T)
x) Breaker failure protection (50BF)
7.5.5.3.1.1 Main fuses shall be used only in motor starters. this fuses shall be striker pin type and
shall have facilities to trip starter and have their own indications when operated.
7.5.5.3.1.2 Eearth fault or earth leakage protection shall be supplied by a corebalance current
transformers and the minimum setting of relay shall be started at least 10% of motor full load
current.
7.5.5.3.2 Motors rating 1000 KW and above

Protection of these size of motors shall be as described in 7.5.5.3.1. (exceprt fuse) and other
protection shall be added as follows:
i) Differential protection (87)
ii) Winding temperature monitor relay (49T)
iii) Bearing over temperature
iv) Phase fault over current protection (50,51)
7.5.5.3.2.1 Winding temperature relay shall have 6 channels to accept ,measures and monitoring 6
RTDs separately.
7.5.5.3.3 Synchronous motors

The protection of this type of motors (2000KW and above) shall be as described in 7.5.5.3.2. and
other protection shall be added as follows:
i) Under excitation protection (40)
ii) Rotor earth fault relay (64R)
iii) Out of step protection (55)
7.5.6 Differntial busbar protection
7.5.6.1 Differential busbar protection should be considered for voltage level of 33 and 63/66 K.V.
outdoor primary substations where the integrity of power supplies and plant operation would be
seriously impaired by loss of a busbar or section of baranch.
7.5.6.2 For metal clad indoor switchgear with busbar insulation as specified in "IPS-M-EL-144 (2)"
the differential busbar protection is not needed.
7.5.6.3.2 Differential busbar protection schemes shall employ high impedance type voltage
operated relays with stabilizing resistors.
93
Feb. 2012
IPS-E-EL-100(1)
7.5.6.3.3 High impedance differential schemes shall have dedicated matched C.T.s of the same
ratio in all incoming and outgoing circuits on the protected busbar or section. Therefore where
busbars are sectionalized by breakers each section shall have its own differential scheme with
C.T.s arranged to over lap at sectionalizing breakers. Class X C.T.s shall be used.
7.5.6.4.1 Test links shall be provided on all C.T.s circuits to facilitate busbar differential scheme
testing.
7.5.6.4.2 busbar protection trips shall be via a single dedicated specific hand reset lock out relay
which shall be arranged to trip the appropriate busbar breakers.
7.5.7 Capacitor protection
7.5.7.1 All capacitor units shall have individually internal fuse elements (according to IEC-60593). If
this is not feasible for certain types of L.V. capacitors, internal over pressure disconnections shall be
provided.
7.5.7.2 All capacitors shall have direct connected means of discharge. L.V. capacitors must
discharge to a residual voltage <75 volts within 3minutes. A maximum discharge time of 10 minutes
is allowed for M.V. capacitors.
7.5.7.3 External H.R.C. fuses are used only for short circuit protection of both M.V. and L.V.
capacitors and do not provide adequate protection against overcurrent.operation of each fuse of
each bank shall disconnect dedicated contactor by means of striker pin or over voltage relay which
is paralleled to that fuse . For M.V. capacitors the minimum accepted rating of fuse is 1.35 times
the rated capacitor current.(acc. to IEC- 60871-3).
7.5.7.4 In case where the capacitor is controlled by circuit breaker, phase and earth fault protection
relays shall be provided.
7.5.7.5 For capacitor banks above 300 KVAR which controlled by contactor, C.T. operated over
load relays should be used. The tripping current of these relays should be set to 1.43 times the
rated current of the capacitor bank.
7.5.7.6 for large capacitor banks exceeding 1000 KVAR the capacitors shall be connected in double
star with unbalance protection monitoring the star point voltage, or with unbalance current
protection between neutrals (according to IEC-60871-3).
7.5.7.7 Air cored reactors shall be installed with M.V. capacitor banks to limit the inrush currents.
7.5.7.8 An interlock system shall be provided for all automatically controlled M.V. capacitor banks to
prevent re-energizing when the residual voltage is above 10% of rated voltage.
7.5.7.9 In those cases where a capacitor is connected in parallel with an electric motor a single
swhich gear device and associated relays and/or fuses that control and protect both the motor and
the capacitor shall be provided.
7.5.8 Over head line protection
7.5.8.1 The lines used in company fields are basically distribution lines and voltage levels are used
up to and include 66 KV. Because of many considerations it is not possible to establish firm rules for
line protection. However, the system design engineer should consider that the operation of
protection on the system will be fully discriminative.
7.5.8.2 Radial lines/feeders

Radial feeders can be protected by non-directional overcurrent and earth fault relay.
i) Phase fault overcurrent protection (50, 51).
94
Feb. 2012
IPS-E-EL-100(1)
iii) Lightning arrester for local and remote end.

iv) Breker failure protection (50BF).
7.5.8.3 Parallel lines incoming feeders
i) Phase fault overcurrent protection (50, 51).

iii) Directional overcurrent protection (67).
iv) Directional earth fault protection (67N).
v) Lightning arrester for local and remote end.
vi) Breker failure protection (50BF).
7.5.8.4 Tee off protection

Teed off lines are normally used to supply the low power installations.( up to 1000 KVA). These
lines are protected by fuses and lightening arrasters.The fuses are placed on both ends; Tee off
end and incoming to the consumer. The selected fuses shall be fully discriminative with the
upstream protective devices.The fuses shall be Cut out type.
7.5.8.5 Auto reclosing system

All over head lines which supplies main substations of oil and gas installations shall be completed
by multi shoot auto reclosing system. This system is initiated by 50 or 50N protection contacts. This
system shall be equipped by a selector switch to give two options for operation:
Auto reclosing in service/ Auto reclosing out of service
7.5.9 L.V. feeder protection
7.5.9.1 Mains and emergency incoming feeders

As described in subsection 7.5.2.1 and 7.5.3
7.5.9.2. Outgoing feeders to:
i) Motors
As described in subsection 7.5.5
ii) Capacitors
As described in subsection 7.5.7
iii) Cables
a) Cables with breaker or isolator at both ends:
For circuits up to 100 A fuse or MCCB and for circuits more than 100 A fuse- contactor or
MCCB together with earth leakage function (decided by company representative if required)
and circuit breaker shall be associated with 505150N51N protection
95
Feb. 2012
IPS-E-EL-100(1)
b) Cables without load end breaker or isolator:

Protection of such cables that connected to equipment such as transformers or motors shall be
achieved by the protection of primary equipment installed at source end.
iv) Electric heaters for process

Protection of electric process heaters shall be by means of fuse or MCCB.
For fuse rating or MCCB trip settings exceeding 100A, earth fault protection shall be provided. Over
temperature protection shall be provided by at least two thermocouples located in the area of the
highest anticipated sheath temperature. When static converters are required to control the heater
output, they shall be equipped with the following as the minimum:
a) Incoming voltage monitoring
b) Fuse protection for the semiconductor devices
c) Over temperature in the converter panel
v) Socket outlets
Outlet circuit shall be protected by phase short circuit protection device and by current operated
earth leakage protective devices, which are according with IEC 60947-2. i.e. residual current circuit
breaker (RCCB). The RCCB operating current shall be 30 mA.
vi) Anti condensation heaters

The heaters shall be protected by a miniature circuit breaker and an earth leakage protection device
at 30 mA. sensitivity (earth leakage will be decided by company representative).
7.5.9.3. Equipments such as battery charger, UPS, cathodic protection system, M.O.V. etc. which
have their own protection, shall be protected by fuse or MCCB incorporating short circuit protection.
7.5.9.4 Lighting
All lighting circuits shall be protected by suitable fuse or MCB.
7.5.10 Instruments, Meters and Instrument transformers
7.5.10.1 Metering and instrumentation are essential to satisfactory plant operation. the amount
depending upon the size and complexity of the plant, as well as economic factors. instruments and
meters are need to monitor plant operating conditions as well as for power billing purposes and for
determination of production costs.
7.5.10.2 Instrument transformers

i) Current transformers shall be in accordance to IEC-60044-1.
ii) The rated secondary current of current transformers should be preferably 5 amperes for
switchgear mounted protective relays and instruments, and 1 ampers for remote mounted protective
relays and instruments.
iii) Current transformers shall have appropriate VA and saturation factor. The saturation factors
shall not be less than 5 for measurement C.T.s.
iv) C.T.s with separate secondary shall be used for protection and measurement duties.
v) Current transformers for high impedance differential and / or restricted earth fault protection shall
be exclusively used for that purpose (class X ).
96
Feb. 2012
IPS-E-EL-100(1)
vi) Voltage transformers shall be to IEC-60186

vii) Voltage transformers shall have appropriate VA and shall not be less than 50 VA.
viii) VTs with separate secondary shall be used for protective and measurement duties.
ix) Voltage transformers for measurement purposes shall be of accuracy class 1 and for protection
purposes shall be class 3P. V.T.s for use with generator AVR/s shall be of accuracy class 0.5.
7.5.10.3 Main M.V. incoming supply

i) Class 1.5 ammeter (with phase selector switch)
ii) Analogue type class 1.5 voltmeter with selector switch on incoming side of circuit
breaker.
iii) Multifunction microprocessor based power measurement meter class 1 (KW, KVAR, KWH, max.
demand, KVARH and so on). Relevant softwear and hardware for comunication porpose and
configuration shall be considered.
7.5.10.4 M.V. out going feeders

i) class 1.5 ammeter (with phase selector switch).
7.5.10.5 M.V. motor starter

i) Ammeter, local / remote refer to 7.5.10.8. below
ii) Power factor meter for synchronous motor
iii) KW meter for synchronous motor
iv) Field current ammeter for synchronous motors.
7.5.10.6 L.V. main incomers

i) Analog voltmeter class 1.5 (with selector switch)
ii) Analog ammeter class 1.5 (with selector switch)
iii) Multifunction microprocessor based power measurement meter class 1 (KW, KVAR, KWH, max.
demand, KVARH and so on) - will be decided by company representatve.
7.5.10.7 L.V. motor starter

i) Ammeter, local/ remote refer to 7.5.10.8.below.
7.5.10.8 Ammeter for motors

Unless specified other wise, the provision of ammeter shall complied with the following:
a) Process area
i) Ammeters shall be provided for motors above 4 KW except for those driving motorized valve,
cranes and winches , furnace fan without vane control and general ancillary equipment such as
drinking water coolers, etc..
ii) Ammeter shall be located adjacent to or be incorporated in the associated push button station.
Current transformer and ammeter for this purposes preferably of accuracy class 3.
97
Feb. 2012
IPS-E-EL-100(1)
b) Other than process area

i) Ammeter shall be provided for motors of above 4 KW as stated under (i) above.
ii) Ammeter shall be located on the motor starter panel in associated sub-station or subdistribution board.
c) Special cases
In certain cases where supervisory control is exercised from a central control position, it may be
necessary to have a meter located at the central control position, typical cases are those of
remotely control crude oil forwarding pumps and /or other process pump derives. when such
arrangements are required they will be specified in view of distances. where indicated in the single
line diagram/and or data sheet, 4-20 MA out put transducer/s complying with IEC 60688 shall be
provided for selected analogue signals to be transmitted to a remote supervisory system such as
distributed control system (DCS). All MV motor starter shall have transducers and for LV motor
starters decided by company representative.
d) General
i) All remote ammeters shall be operated from a current transformer mounted in the motor starter
panel.
ii) Scales shall be selected so that full load current appears between 50% and 70% of full angular
deflection. full load motor current (design value) shall be indicated by a red line on the scale.
iii) Ammeters for motors shall be capable of repeatedly withstanding the appropriate motor starting
current without accuracy being impaired. the ammeter scal shall be shown 6 times motor reted
current.
7.5.10.9 Generators
7.5.10.9.1 M.V. generators

The following instruments and meters shall be provided at the relevant control locations for M.V.
generators:
i) KW meter
ii) Power factor meter
iii) KVAR meter
iv) Analog voltmeter (with phase selector switch)
v) Ammeter (with phase selector switch)
vi) Frequency meter
vii) KWH meter
viii) Elapsed time meter
ix) Dc field current ammeter
Where remote monitoring of generators output is required, such as in main control room, suitable
transducers shall be provided at the generator switchgear to facilitate this.
7.5.10.9.2 L.V. generators up to and include 500 KVA

i) Analog voltmeter (with phase selector switch)
ii) Analog frequency meter
98
Feb. 2012
IPS-E-EL-100(1)
iii) Ammeter (with phase selector switch)

iv) Power factor meter
v) KW / KVAR meter
vi) Elapsed time meter
7.5.10.9.3 L.V. generators above 500 KVA

As described in 7.5.10.9.1
In case of paralleling of two sources of supply or generator synchronizing system is required.
7.5.10.9.4 Special C.T. and V.T. requirement for generators

i) The primary rating of line C.T.s should bel approximated 150% full load current of the generator.
Neutral connection C.T.s shall have a primary rating at least equal to resistance rating. for
generators earthed via a power transformer the neutral connected C.T. shall be a 1:1 ratio.
ii) VTs for the AVR shall be exclusively used. The same policy shall be adopted for VTs for
synchronizing .these VTs shall not be single phase.
7.5.11 Control, tripping and alarm
7.5.11.1 H.V., M.V., L.V. control and automation
7.5.11.1.1 Switchgear on M.V. and H.V. system shall not be controlled directly from the front of the
circuit breaker panel. The operation of switchgear shall be from a separate control panel within the
substation or from a completely separate room. The closing of switchgear shall be provided in front
of switchgear panel only for test position.
7.5.11.1.2 Local tripping facilities shall be provided even when remote control is applied.
7.5.11.1.3 Automatic transfer system shall be applied to LV, MV and HV incomers. This system
initiates closing order to bus section C.B. when one of the incomers losses their supply.
7.5.11.1.4 Manual transfer system shall be applied to LV, MV and HV motor control center. This
achieved by means of synchro check relay and relevant selector switches. By this system it shall be
possible to change each incomer by bus section C.B. and vice versa without any interruption of
supply. Use of PLC devices with suitable lader diagram (alghoritm) is acceptable.
7.5.11.1.5 Automatic transfer shall be applied to L.V. emergency generator and main supply. This is
achieved by own generator solid state control system. Adequate interlocks shall be considered to
prevent closing of main circuit breaker and generator circuit breaker simultaneously.
7.5.11.1.6 When the main supply restored, transfer from generator to mains shall be achieved by a
pushbutton installed in generator control panel.
7.5.11.2 Tripping and alarm
7.5.11.2.1 Tripping of all circuit breakers shall be initiated by separate tripping relay (86). The relay
operating coil shall be energized by protective schemes. The relay shall be heavy duty and hand
reset type with clear reset trip indication.
7.5.11.2.2 The triping and closing circuit, alarm circuit, microproccessor based meters and relays
auxiliary supply and C.B. motor charging supply circuit shall be supplied by four distinct fuses with
appropriate sizes.
99
Feb. 2012
IPS-E-EL-100(1)
7.5.11.2.3. Each feeder at least shall have four indication lamps on panel:
i)
Red lamp for close position
ii)
Green lamp for open position
iii) Yellow or orange lamp for tripping or fault purpose

iv) Red lamp for earth switch close position
v)
The trip circuit supervision system (T.C.S.) shall be achieved by use of digital input of
microproccessor base relay with assosiated LED, or with separate T.C.S relay.
7.5.12 Power management system
7.5.12.1 General
A Suitable Power management system shall be provided to facilitate management of the whole
electrical Power generation and distribution system within utility plants. The power management
system shall be designed in such away to allow:
i)
Synchronizing of generators, if any
ii)
Automatic load sharing between running generators
iii) Automatic load shedding/restoration

iv) Loop reconfiguration
v)
Main distribution system (HV/MV AND main LV switchgears) operation and reconnection
vi) Graphic representation of substation single line diagram

vii) Continuous monitoring of main and emergency generators
viii) Continuous monitoring of HV/MV and main LV switchgears
ix) Management of emergency diesel generator
x) Alarm annunciation of main and emergency generators
xi) Alarm annunciation of power distribution i.e. switchgear, charger
xii) Import/Export MW, MVAR, MWH and MVARH From/to the network shall be recorded in power
management system
xiii) Time-dependent programming and tariff management
xiv) Fault recording
7.5.12.2 Mode of operation

Operator shall be able to select the manual control mode or automatic control mode from PMS work
station.
7.5.12.2.1 Manual control

In this mode of operation, operator shall be able to close and open all incomings and bus couplings
in HV/MV and main LV switch boards plus MV outgoing Feeders (Except Motors Starters) From
PMS work station.
In addition, in this mode of operation, operator shall be able to remotely start, stop or parallel main
generators and stop, starts emergency diesel generator and also close/trip associated circuit
breakers.
7.5.12.2.2 All safety means shall be considered such away to ensure operations described in 2.1
will be safe and according to inter locking system of system philosophy.
100
Feb. 2012
IPS-E-EL-100(1)
7.5.12.2.3 Automatic control

Automatic control mode consists of some automatic sequence that shall be programmed in to PMS.
These sequence shall control all incoming and coupling in HV/MV and main LV switchgear and also
emergency diesel generator. Some features areas below:
i) Automatically close bus coupler in loss of 1 incoming voltage.
ii) Automatically Running diesel generator in total network loss.
7.5.12.2.4 Manual transfer

Due to a maintenance schedule or any reason, in manual transfer mode operator shall be able to
change one incoming by coupling (and vice versa) without any interruption in supply of whole
HV/MV or main LV bus bars.
7.5.12.3 System architecture

In order to run an electrical network and its associated Automatic system, a control and monitoring
system uses computer hardware in combination with a set of software applications all of which
communication over a network.
So that the PMS shall be consist of:
i) Main rack cabinet with internal marshaling board
ii) Main sever computer as MMI, consist of one printer, one 19'' LCD display, keyboard and mouse
mounted on suitable work desk
iii) Required software
iv) Communication network and interconnections
v) Gate way to other computer system
vi) Synchronization of various pieces of equipment
vii) Electrical power supply shall be 110 OR 230 V AC 50 HZ single phase from UPS
7.6 Batteries, Chargers and UPS
7.6.1 General
This section defines general requirements for electrical power switchgear substation supplies and
distribution for control systems. Such control systems may include instrumentation, data collection,
fire and gas detection systems, telecommunication equipment, computers and associated
equipment and may be onshore or offshore, within established infrastructures or in remote
locations.
7.6.1.1 Control systems and their power supplies

Control systems and their power supplies shall be selected as Class A or Class B to reflect the
following factors as stated in IPS-E-IN-180 (1):
3TU
U3T
i) The required availability of each part of the overall system.

The importance of the connected load in terms of overall plant operation.
ii) The control system loads shall be tabulated and their classification defined. The definition of the
classes is given in 7.6.1.2 to 7.6.1.4.
101
Feb. 2012
IPS-E-EL-100(1)
7.6.1.2 Class a systems

Class A systems are defined as those which by malfunction or failure can cause any of the
following:
a) A shutdown of the whole or major part of a plant or process
b) A failure to shut down, under emergency conditions, the whole or major part of a plant or
process.
c) A loss of monitoring facilities on any equipment which may itself cause a shutdown of the whole
or major part of a plant or process.
d) A loss of alarm annunciation for fire and gas detection
Note 1:
Emergency and shutdown systems such as ESD and F&G shall be classified class A.
Note 2:
Some equipment requires a single power source and then sub-divides this for multiple
purposes. Where any of these purposes are classified as Class A, then the entire system
shall be classified as Class A.
Note 3:
Flame failure devices or monitoring equipment on certain items of machinery which are
critical to the whole or major part of a plant shall be considered as Class A systems.
7.6.1.3 Class B systems
Class B systems are defined as those which their malfunction or failure can cause any of the
following:
A degradation of normal control or monitoring of the plant or process where alternative methods of
control, such as local plant control panels, hand wheels etc are available.
A loss of alarm annunciation facilities not Covered by 7.6.1.2.
7.6.1.4 Class C systems

Apparatus is that by their malfunction or failure cannot directly prevent the operation of the plant.
This class comprises of indicators, integrators, recorders and most analyzers.
7.6.2 Basic design requirements
7.6.2.1 Design of DC power supplies shall comply with IPS-M-EL-174(2) and AC power supplies
shall comply with IPS-M-EL-176(2).
7.6.2.2 Voltage levels of supplies to all equipment shall be selected according to a sensible
evaluation of systems which may be already existed on a plant. Supplies to control systems should
not exceed nominal voltages of 120V r.m.s AC or 120V Dc (nominal 24V DC. for control instruments
supply and 110 volts DC is used for switchgear supply shall be considered as default).
7.6.2.3 Wherever possible, power supply equipment shall be located in a non hazardous area.
102
Feb. 2012
IPS-E-EL-100(1)
7.6.3 Particular requirements: class a power supplies
7.6.3.1 Class A power supplies shall automatically maintain a continuously uninterrupted electricity
supply within required control system tolerances upon failure or deterioration of the primary source,
or any other item of the power conversion equipment.
7.6.3.2 Duplicate fully rated rectifier-battery systems shall be used. The AC supplies to the rectifiers
shall be supplied from different switchboards or different busbars of the same switchboard. Where
standby or emergency generation is available, at least one of the AC supplies to the rectifiers shall
be supplied from the generator busbar.
7.6.3.3 Class A power systems shall be designed such that upon the occurrence of a fault in any
one incoming power circuit, the faulty circuit shall be isolated without supply disruption and the
alternative supply shall then maintain the load within the defined tolerance.
7.6.3.4 Autonomy time for, class A, dc loads shall be as indicated in IPS-E-IN-180.
7.6.3.5 Autonomy time for F& G systems shall be as indicated in IPS-E-SF-260.
7.6.3.6 Autonomy time for switchgear control system in attendant plants shall be as indicated in
IPS-M-EL-174(2).
7.6.3.7 Autonomy time for switchgear control system in non attendant plants shall be 8 hours.
7.6.3.8 Each charger shall be sized to supply total load plus 0.2C 5 of total battery capacity required.
7.6.4 Particular requirements: class b power supplies

7.6.4.1 Class B power supplies may be DC or AC and, after primary supply loss, shall automatically
maintain continuity of electricity supply within the specified control system tolerances for a period of
60 min, or as otherwise specified. Normal and standby circuits shall be provided. The changeover
on failure of the normal circuit shall not affect process operations.
For those systems requiring DC power, the normal circuit shall be via a rectifier-battery system and
the standby circuit via battery.
For those systems requiring AC power, the normal circuit shall be via rectifier-battery-inverters. The
standby circuit which will feed the load, through static switch during inverter failure shall be
connected to the primary AC source. The AC supplies to the normal and standby circuits shall be
supplied from different switchboards or different busbars of the same switchboard. Where
emergency generation is available, one of the circuits shall be supplied from the generator busbar.
"Class B" AC power supplies should not produce any transients due to changeover which could
cause mal-operation of the connected equipment.
7.6.5 Particular requirements: class c power supplies

"Class C" power supplies should normally be AC and fed from a primary source without standby.
7.6.6 Power supply configurations for different classes
7.6.6.1 "Class A"

"Class A" power supply shall consist of two similar static battery chargers each rated 100% and two
battery bank each rated for 50% of required capacity and one distribution panel. Technical
requirement for design, manufacturer, quality control and testing of battery chargers, batteries and
DC distribution panel shall comply with IPS-M-EL-174(2).single line diagram of proposed system is
shown in Fig. 7
Power supplies are shown in following Fig. 7 shall be provided from main and emergency busbars.
103
Feb. 2012
IPS-E-EL-100(1)
SINGLE LINE DIAGRAM OF PROPOSED SYSTEM (HOT DUTY STANDBY TOPOLOGY)

Fig. 7
Where DC is not technically acceptable to the manufacturer of the control equipment, AC power
supply is acceptable. In such case dual redundant ups shall be used. Dual parallel redundant ups
are indicated in Fig. 8.
104
Feb. 2012
IPS-E-EL-100(1)
PARALLEL REDUNDANT CONFIGURATION

Fig. 8
In case where DCS with dual redundant controls is used two identical single battery charger or two
identical single ups as indicated in Fig. 9 can be used.
105
Feb. 2012
IPS-E-EL-100(1)
SINGLE LINE DIAGRAM OF DUAL PARALLEL LOAD SHARING UPS CONFIGURATION

Fig. 9
106
Feb. 2012
IPS-E-EL-100(1)
7.6.6.2 Class B
7.6.6.2.1 Class B power supply may be DC or AC and after primary power supply loss shall
automatically maintain continuity of supply.
7.6.6.2.2 In case of DC power supply, a single battery charger with one bank of battery as indicated
in Fig. 10 can be used.
A SINGLE BATTERY CHARGER WITH ONE BANK OF BATTERY

Fig. 10
7.6.6.2.3 For ac power supply single UPS as indicated in Fig. 11 can be used. For material standard
refer to be made to IPS-M-EL-176(1) single unit.
AC POWER SUPPLY SINGLE UPS

Fig. 11
7.6.7 Battery rooms
7.6.7.1 Introduction
Since Hydrogen gas is normally evolved during charging phase of battery operation, some
requirements regarding battery room construction shall be considered.
107
Feb. 2012
IPS-E-EL-100(1)
7.6.7.2 Design aspects recommended considerations
7.6.7.2.1 All electrical equipments installed inside of battery room shall be explosion proof type.
7.6.7.2.2 A Hydrogen in air mixture of 4% or greater substantially increases the risk of an
explosion. The concentration of Hydrogen shall be kept below 1 % to provide a safety factor. For
volume of Hydrogen release and ventilation refer to battery manufacturer recommendations.
7.6.7.2.3 Smoke detectors and Hydrogen detectors shall be installed in battery rooms.
7.6.7.2.4 The room ceiling shall be flat to ensure that pockets of trapped Hydrogen gas do not
occur. False ceiling shall not be used for battery rooms.
7.6.7.2.5 Carbon Dioxide portable fire extinguisher shall be installed in battery rooms.
7.6.7.2.6 Batteries installed outside battery rooms, e.g. in service plant, shall be installed in non
metallic cabinets. These cabinets shall be naturally ventilated and either house the battery alone or
the battery in combination with the associated battery charger.
7.6.7.2.7 In battery rooms, eyewash fountain and flow water drain shall be provided.
7.6.7.2.8 The floor and walls of battery rooms shall be covered by ceramic tiles.
7.6.7.2.9 No trench shall be constructed in battery rooms.
7.6.7.2.10 The door of battery rooms shall be opened toward outside.
7.6.7.2.11 The size of a room shall be adequate to allow access to at least three sides of each
battery bank for maintenance purposes.
7.6.7.3 Applicable standard battery room ventilation requirements

To achieve clause 7.6.7.2.2 the following methods are recommended:
-
12 air changes per hour for battery room
Forced air supply & positive exhaust system
Air inlets to be located near the floor & outlet openings at the high point in the room,
See Fig. 12:
AIR CIRCULATION IN BATTERY ROOMS

Fig. 12
7.7 Power Cables
7.7.1 Scope
This standard specifies the requirements for the design, selection, application and installation of
multicore and single core cables which are required to have copper conductors for use on systems
up to and including 33 kV for the purpose of power, control, indication and protection.
108
Feb. 2012
IPS-E-EL-100(1)
7.7.2 Cable system design
7.7.2.1 Voltage rating
7.7.2.1.1 The voltage designation or rating, Uo/U, should be selected from the standard ratings
given in the relevant cable standard, e.g. 600/1000V, 3600/6000V, etc., and shall be appropriate to
the type of system and the earthing arrangements. Uo is the voltage between phase conductors
and earth and U is the voltage between phase conductors.
7.7.2.1.2 The voltage levels adopted in the oil, gas and petrochemical industries of Iran are based
on the IEC 60038.
7.7.2.1.3 The cables designated up to and including 0.6/1 kV rms are called low voltage (LV)
cables, the cables designated above 0.6/1 kV rms and up to and including 3.6/6 kV rms are called
medium voltage (MV) cables, and the cables designated 6/10 kV, 12/20 kV and 18/30 kV are called
high voltage (HV) cables.
7.7.2.2 Current carrying capacity
7.7.2.2.1 Cables shall be sized to operate within their current carrying capacity as determined by
the maximum continuous temperature of the insulation, see Table 14.
Note:
Several factors are involved in the sizing of conductors and whilst continuous current
capacity is paramount, others such as voltage drop and ability to carry short circuit currents
must not be neglected.
7.7.2.2.2 In assessing the size of conductor required for a given design current the following factors
shall be taken into account:
- Ambient temperature
- Grouping and proximity to other loaded cables
- Method of installation
- Thermal conductivity of the medium in which the cable is installed.
- Thermal conductivity of the cable constituents.
7.7.2.2.3 The design current,
I d , shall be determined as follows:
Circuits supplying single fixed loads

I d = rated current of the load.
Note:
Circuits supplying two or more final subcircuits should be rated in accordance with the total
connected load but may, where justified, be subjected to application of diversity factor.
Radial circuits supplying socket outlets
I d = rated current of the socket outlet
Incoming feeders to switchboards and sub-distribution panels.
I d = maximum current associated with peak design production with an additional 10% contingency.
109
IPS-E-EL-100(1)
Feb. 2012
Note:
The maximum current should account for appropriate application of diversity factors. Such
allowances require the judgement of a qualified electrical engineer with knowledge of the
operational requirements of the plant.
Typically, where switchboards are fed by transformers, the incoming cables are sized to the rating
of the transformer. Where there are no infeed transformers to the switchboard or sub-distribution
panel, then the infeed cables are sized to the rating of the incoming switch or busbar whichever is
the smaller.
7.7.2.2.4 Where cables are laid in mixed groups of different types, sizes and loading, the group
rating factor of each cable should be calculated or assessed for each cable, taking into
consideration the thermal effect of all the other cables of the group. IEC 60287 provides the
mathematical basis for determining individual cables ratings when installed in mixed groups.
7.7.2.2.5 For 3 phase, 4 wire circuits, multicore cables the neutral conductor shall be no smaller
than 50% of the size of the phase conductors. Reduced sizing of neutral conductors should not be
applied where there is likely to be serious load imbalance, significant harmonic distortion in normal
service or in any circuit where the load is predominately discharge lighting.
7.7.2.3 Short-circuit rating
7.7.2.3.1 The short time maximum current carrying capacity of the cable should be considered with
regards the current/time characteristics of the circuit protection device to ensure that cables do not
suffer damage due to overheating under maximum through fault conditions. In some cases,
particularly where cables are protected by non-current limiting circuit breakers, the cable size is
determined by the magnitude and duration of the maximum through fault current, rather than by the
continuous current capacity or voltage drop constraints.
7.7.2.3.2 The minimum cross-sectional area should be assessed from the following formula:
A=
I t
K
(mm 2 )
where:
A = Cross sectional area of the conductor
(mm 2 )
I = Short circuit current (amps)

t = Total fault clearance time (seconds)
K = Constant dependent on the type of conductor, the insulations, the initial and final
temperatures.
Values of K for various types of insulation in contact with copper conductors are given in Table 14.
TABLE 14 - MAXIMUM PERMITTED CONDUCTOR TEMPERATURES AND VALUES OF K FOR

VARIOUS INSULANTS (COPPER CONDUCTORS)
Insulation
Cable types
PVC
PVC
EPR
XLPE
Up to 185 mm
2
240 mm and above
All types
All types
Maximum
working
temp
o
T1 C
70
70
85
90
Final temp
at end of
short circuit
o
T2 C
150
130
220
250
Value of K
for temps
T 1 ,T 2
109
95
134
143
The values of K given in Table 14 assume that the cable is operating at its maximum current
carrying capacity. If this is not the case, true value may be determined from the formula:
110
Feb. 2012
K = 225.7 Ln
IPS-E-EL-100(1)
234.5 + T2
234.5 + T1
o
Where: T 1 = initial temperature of conductor ( C)

o
T 2 = final temperature of conductor ( C)
Note:
For medium voltage power cables controlled by circuit breaker, the minimum fault clearance
time shall be considered 0.3 seconds.
7.7.2.4 Voltage Drop
7.7.2.4.1 Cables shall be sized so that the maximum voltage drop between the supply source and
the load when carrying the design current does not exceed that which will ensure safe and efficient
operation of the associated apparatus, or 5% of nominal voltage, whichever is lower.
The supply source will be the switchboard or MCC upstream of the load, at which the voltage can
be adjusted. This adjustment can be made either by changing taps on the incoming transformers or
through AVRs of directly connected generators. In the majority of cases the load will be connected
directly to the supply source through a single cable. However there will be cases where the load is
fed from a sub-circuit and in such cases there may be two interposing cables between the load and
the supply source. In such cases the permissible voltage drop of 5% needs to be accounted for
from the supply source through the two series connected cables to the load terminals.
The maximum cable length for a low-voltage motor of given rating may be calculated from the
following formulas:
Ls =
Vs 1000
3I s ( R cos s + X sin s )
Lr =
Vr 1000
3I r ( R cos r + X sin r )
The maximum route length is the lesser of these two lengths.
R = Cable resistance ohms/kM

X = Cable reactance ohms/kM
L = Maximum cable length (m)
V = Maximum cable volt drop (V)
I = Motor current
(A)
= Motor power factor
Subscripts r and s refe r to running and starting values of the above parameters respectively.
7.7.2.4.2 Cables shall be sized so that during motor starting, voltages throughout the network shall
not fall by more than 15% of nominal values.
7.7.2.4.3 For medium and high-voltage motors, the voltage drop along the cable to the motor due to
the load current shall not exceed 3.25% of nominal voltage during normal running at full load.
111
Feb. 2012
IPS-E-EL-100(1)
7.7.2.5 Computer-aided design of cable systems

Computer-aided design methods may be used to solve problems of cable sizing, route allocation
and traywork design, provided that accepted criteria are used consistent with this document and
that the resulting design is both technically adequate and economical.
7.7.2.6 Documentation
The documentation requirements for the cable system design shall be agreed with the company
representative. The following is a guide of typical requirements:
7.7.2.6.1 Design dossier including basis of cable sizing together with specimen calculations. This
dossier should normally form part of the permanent records of the site.
7.7.2.6.2 Cable routing diagrams.
7.7.2.6.3 Constructional details of cable traywork and cable tray support systems.
7.7.2.6.4 Cross sections of cable routes showing the actual arrangement of cables, and separation
distances.
7.7.2.6.5 Interconnection diagrams showing the cable numbers, the core identification numbers and
equipment terminal numbers.
7.7.2.6.6 Cable schedules.
7.7.2.6.7 Cable gland schedule.
7.7.3 Selection of cables

7.7.3.1 General
7.7.3.1.1 For onshore installation, the conductors shall be circular plain annealed stranded copper
in accordance with IEC 60228.
7.7.3.1.2 No PVC cable should be installed at temperatures lower than 0 degC unless special low
temperature grade PVC has been specified, in which case installation at ambient temperatures
down to -10 degC may be possible.
7.7.3.1.3 Depending on the possibility of soil contamination or chemical attack, specially in process
areas, cables shall be provided with a lead sheath.
7.7.3.1.4 Unless the soil will definitely remain free from contamination, lead sheathed underground
cable shall be used in oil and chemical plants.
7.7.3.1.5 The use of multicore cables is preferred to single core cables. However, single core cables
may be used for practical and/or economic reasons on short runs, e.g. generator and transformer
secondary cables or in the case of high current ratings where two parallel multicore cables of the
largest cross section permitted would not suffice.
7.7.3.1.6 Cables for protection, controls, indications and alarms for a particular item of plant or
circuit (e.g. generator, motor, transformer, etc.) shall be dedicated to that item of plant or circuit.
7.7.3.1.7 Individual cables shall be used for each of the following:
CT secondary
VT secondary
Interlock / intertrip circuits
Pilot wire differential circuits
Note:
The requirements of the preceding paragraph do not apply to motor control and ammeter
circuits to a Remote Control unit (RCU), nor to combined power and control circuits to small
LV motors.
112
Feb. 2012
IPS-E-EL-100(1)
7.7.3.1.8 The armouring of single core power cables shall be made of non magnetic materials.
7.7.3.1.9 All power, lighting, control and earthing cables shall be in accordance with the latest
version of IPS-M-EL-271, 272 and 273.
7.7.3.2 Medium and high voltage power cables
Medium and high voltage cables shall be copper conductor with Cross Linked Polyethylene (XLPE)
insulation, lead sheathed, single wire armoured and PVC overall jacket.
2
MV and HV multicore and single core cables shall have a minimum cross sectional area of 50 mm .
2
MV and HV multicore cables shall have a maximum cross sectional area of 240 mm .
2
MV and HV single core cables shall have a maximum cross sectional area of 400 mm , Unless
otherwise approved by the company representative.
Selection of single or multicore cables shall be approved by the company representative.
7.7.3.3 Low voltage cables
7.7.3.3.1 Power cables

Low voltage power cables shall be copper conductor with XLPE or PVC insulation 600/1000 V
grade, lead sheathed, single wire armoured, with PVC overall jacket. These cables shall be used for
above ground and underground installations.
2
For low voltage single core power cable, conductor sizes up to and including 10 mm can be solid
copper.
Unless otherwise approved by the company representative, the maximum conductor cross section
2
2
shall be limited to 240 mm for low voltage 3 and 4 core power cables and 400 mm for low voltage
single core power cables.
7.7.3.3.2 Control cables

Twin and multicore lighting and control cables shall be copper conductor with PVC insulation
600/1000 V grade, lead sheathed, single wire armoured, with PVC overall jacket.These cables shall
be used for above ground and underground installations.Unless otherwise approved by the
2
company representative, the minimum cross section for lighting and control cables shall be 2.5 mm
2
except for signaling and indication purposes, where a minimum cross section of 1.5 mm _ may be
used.
7.7.3.3.3 Mineral insulated copper sheathed cables
a) In areas where high temperature is expected, mineral insulated or heat resistant coppersheathed cables (MICC) shall be used for small power and control.
b) Where mineral insulated cables are specified, the cables shall be copper conductor, copper
sheathed with PVC outer covering. The mineral insulated cables shall be manufactured
according to IEC 60702-1.
c) Mineral insulated copper-sheathed cable (MICC) should in general be restricted to domestic,
commercial and light industrial applications such as in offices, accommodation modules,
substations, control rooms and workshops. Its inherent, but limited, fire resistant properties can
make MICC suitable for essential circuits such as fire alarms, although it may also be used more
generally for power, lighting, heating and air conditioning plant.
113
Feb. 2012
IPS-E-EL-100(1)
d) MICC shall not be used in situations where the equipment to which it is connected is subject to
vibration or where the cable may need to be disconnected regularly for maintenance. A loop of
cable shall be formed just before the gland where MICC is connected to a motor.
e) Where MICC is to be used in a highly inductive circuit, precautions may need to be taken to
protect against breakdown due to the high transient voltage which occurs on switching the
current off. In such cases, cables shall be protected by suitable surge suppressers across the
supply terminals.
f) MICC used indoors in dry locations may be bare copper sheathed. However, where such cables
are used outdoors or where appearance is to be a consideration, they shall have an over sheath
of PVC.
7.7.3.3.4 Earthing cables

Earthing cables and wires shall be single core with plain stranded or solid copper conductor, PVC
sheathed rated voltage of 600 V, coloured green - yellow for both underground and above ground
use. The PVC sheath is a protection against electrolytic corrosion.
7.7.3.3.5 Wires
Low voltage wires shall be stranded or solid copper conductor, PVC insulated, rated voltage 600
volt according to IEC 60227. Wires shall be suitable for installation in rigid steel galvanized conduits
2
or truncking. Minimum cross section shall be 2.5 mm . Wires in conduit systems shall be applied
only for lighting, communication and convenience outlets in closed buildings in non-hazardous
areas. The insulation color of low voltage wires shall be according to IPS-M-EL-271.
7.7.3.3.6 Flexible cables

Flexible cables for voltages up to 450V to neutral shall be heavy duty neoprene rubber insulated,
PVC sheathed. For applications where the equipment connected to the power or control cable is
subject to vibration, flexible cables or wires shall be used. Flexible cables and wires shall be
capable of withstanding bending and other mechanical stresses occurring in normal use and shall
comply with the requirements of IEC 60227-2.
7.7.3.4 Cables for use offshore
7.7.3.4.1 Conductors shall be longitudinally water sealed stranded copper wires, conforming to
class 2 of IEC 60228.
7.7.3.4.2 The insulation shall be extruded Cross Linked Polyethylene (XLPE). Ethylene-Propylene
Rubber (EPR) insulation may be quoted as an option.
7.7.3.4.3 Cables used offshore for any application other than one calling for a fire resistant cable,
should normally be Flame retardant. For small projects requiring limited quantities, cables by EPR
insulated, galvanised steel or copper alloy braid armour,accordance to IEC 60092-3 shall be used
where economical or expedient.
7.7.3.4.4 Where an armour is required for single core cables it shall consist of a phosphor bronze
wire braid complying with IEC 60092-3.
Note:
Submarine cables selection shall be accordance with the IPS-M-EL-273(1).
114
Feb. 2012
IPS-E-EL-100(1)
7.7.3.5 Cables for special fire risk areas
7.7.3.5.1 When cable routes are being planned, special fire risk areas shall be avoided as far as
possible. Fire risk diagram(s) indicating areas of fire risk and the sources of fire hazard shall be
produced.
7.7.3.5.2 Within a special fire risk area, the following types of circuit shall be fire resistant, i.e. able
to continue operating in the presence of a fire of specified temperature and duration.
- Circuits necessary to provide a safe and orderly shutdown of the plant, including essential
instrumentation and monitoring circuits.
- Emergency or 'escape' lighting.
- Cables essential for the operation of life saving equipment, e.g. fire alarms, evacuation alarms,
gas detection, etc.
7.7.3.5.3 Depending on the application and the fire withstand requirements, cables shall be Fire
resistant cable. Alternatively, MICC may be used, subject to the restrictions of section 7.7.3.3.
7.7.3.5.4 Cables in special fire risk areas which do not fall into any of the categories of 7.7.3.5.2
shall have flame retardant properties in accordance with IEC 60332-3.
7.7.3.5.5 For most installations, except as required in 4.5.2, fire resistant cables should not be
specified solely to attempt to keep a plant operating in the event of a fire. In the case of the
emergency lighting, a combination of floodlighting and selfmaintained luminaries should be used to
reduce the amount of cable exposed to fire risk.
7.7.3.6 Environmental considerations

Cables shall be constructed with suitable sheathing materials which will withstand exposure to the
environment in which they are installed. Wherever possible, however,measures shall be taken to
avoid prolonged exposure to conditions which could in the long term produce degradation of the
cable.
Specific attention shall be given to the following environmental factors:
7.7.3.6.1 Exposure to seawater or salt spray.
7.7.3.6.2 Exposure to intense heat radiation from the sun or from a flare.
7.7.3.6.3 Excessively high or low ambient temperatures.
7.7.4 Cable installation methods and materials

Refer to IPS-C-EL-115(1).
7.8 Static power factor correction equipment
7.8.1 General requirements

1) In electrical circuits, industrial capacitors or synchronous motors are used in order to decrease
reactive power and power factor correction.
2) Absolute reactive power of capacitor is calculated as follow:
Q C = V eff I eff Sin ; I eff = Veff / | Zc | = V eff 2 FC ; = / 2
2
Then : Q C = 2 F C V eff
115
Feb. 2012
IPS-E-EL-100(1)
In which :
Q C : Absolute reactive power of capacitor
V eff : RMS voltage of capacitor
I eff : RMS current of capacitor
F : Frequency
C : capacitance
3) Distortions and harmonics which are due to non linear loads result in decreasing power factor
and this can not be corrected by capacitors however it needs filters.
4) Where the calculated system power factor at full load is less than 85% lagging, capacitor bank/s
shall be installed. The capacitor bank/s shall be sized to improve the system power factor to 95%
lagging at system full load.
5) In case where the calculated system power factor at full load is more than 85% but less than 90%
lagging, power factor correction capacitor/s will be required when power is received from outside
source/s. In such case the capacitor bank/s shall be sized to improve the system power factor to
95% lagging at system full load.
6) Capacitor banks can be installed in the main power plant or individual substations.
7) Capacitor banks shall be permanently energized. Installation of capacitors parallel to individual
motors which is switched on and off together with the motor is not desirable.
8) Low voltage capacitors shall be of the self-healing type and shall comply with the requirements of
IEC 60831 and may be of either three phase or single phase construction.
9) For further information refer to latest version of IPS-M-EL-181.
7.8.2 Capacitor sizing method

The Capacitance calculation of capacitor units and a method for this calculation is as below:
; Q 1 = P tan 1
a) P = 3 V L-L I L Cos 1
In which :
Cos 1 : Primary power factor
P : Total active power
Q 1 : Primary reactive power
b) Q 2 = P tan 2
In which:
Cos 2 : Power factor after correction
Q 2 : Reactive power after correction
c) Q c = Q 1 - Q 2
In which:
Q c : Produced reactive power of capacitor
d) Q c = P [ tan 1 - tan 2 ]
Example: For power factor correction from 0.6 to 0.96 in the unit with RMS load of 300 KVA we will
have this according to above :
116
IPS-E-EL-100(1)
Feb. 2012
Cos 1 = 0.6 Cos 2 = 0.96
P = 300 0.6 =180 Kw , tan 1 = 1.33 , tan 2 = 0.29
So: Q C = 180 (1.33-0.29) = 187 KVAR
R
7.8.3 Service condition

Refer to latest revision of IPS-M-EL-181.
3TU
U3T
7.8.4 Synchronous motors

Wherever synchronous motors are supplied for power factor correction they shall included constant
power factor control equipment.
7.9 Overhead Lines

Refer to latest revision of IPS-E-EL-160.
3TU
U3T
7.10 Lighting
Scope :The purpose of this section is the provision of lighting fitting, illumination, emergency,
security lighting and special lighting for the industrial and non industrial plant areas.
7.10.1 General lighting requirements
7.10.1.1 The lighting in the process plants shall be fluorescent type in white color as far as practical,
flood lights with mercury vapor lamps can be used where applicable.
7.10.1.2 Long life lamps in combination with electronic ballasts shall be used in new installations,
and for upgrading old installations, so as to take advantage of their increased lumen
efficiency and economic life.
7.10.1.3 The lighting fixtures for street lighting and high industrial buildings such as generator
buildings, compressor buildings, workshops and similar, shall be with mercury vapor lamps. In view
of the restarting time of this type of lighting after a voltage dip, sufficient fluorescent luminaries shall
be installed for basic lighting requirements of the area, equivalent to emergency lighting
requirements.
7.10.1.4 Consideration shall be given to the use of floodlighting, especially around the perimeter of
process and production plants. Care must be exercised to ensure that this does not result in
shadows, especially at operating locations.
7.10.1.5 Low pressure sodium discharge lamps shall not be used in process area, as they
constitute a fire hazard in the event of breakage.
For selection of lighting equipment refer to IPS-M-EL-161(1).
3TU
3T
7.10.2 Plant lighting
7.10.2.1 Plant lighting circuits shall be fed from dedicated lighting distribution boards installed in the
plant substations.
7.10.2.2 Plant lighting circuits shall be single phase and neutral or three phases and neutral. Plant
lighting distribution boards shall include 20% spare outgoing circuits.
117
IPS-E-EL-100(1)
Feb. 2012
7.10.2.3 Adjacent luminaries shall not be supplied from the same circuit, or in case of three phase
circuits, from the same phase.
7.10.2.4 As far as practical fluorescent lighting shall be used throughout the plant installations. The
lighting system shall be designed to give illumination levels as shown in Table 15.
Lighting installations shall be designed to obviate stroboscopic effects.
7.10.2.5 Luminaries on structures shall be so located that maintenance and lamp changing can be
effected without the use of ladders or scaffolding. In cases where luminaries mounted from an
elevated walkway or platform does not overhang it, the lamp post shall be arranged to swivel for
maintenance purposes. In high buildings, such as compressor and turbo generator houses,
maintenance and lamp-changing shall be possible by using the overhead crane.
7.10.2.6 Where no structure is available to support luminaries, fixed lighting poles of adequate
length with high pressure discharge floodlighting shall be used to supplement the fluorescent
luminaries. Lighting poles shall be in accordance with IPS-M-EL-161(1).
3TU
U3T
7.10.2.7 For fixed floodlighting columns lamp changing will be carried out using a mobile platform,
e.g. vehicle mounted. Alternatively, hinged lighting columns may be used, if space is available for
the columns to be lowered.
7.10.2.8 Plant lighting circuits shall be designed for automatic switching via photo-electric relays.
7.10.2.9 Control circuits for photo-electric relays shall be fail-safe, i.e. to switch the lights on if a
fault occurs in the photo-electric relay. The plant lighting shall be designed in such a way that in
daytime the lighting of furnaces, boilers and the ground level plant can be switched on by means of
a switch overriding the appropriate photo-electric relay contact. The remaining photo-electric relayoperated plant lighting shall have the facility to be switched off at night-time. These override
switches shall be located either outside the plant substation or in the control room, as required by
plant operations. Moreover, the lighting distribution board shall be provided with an override switch
for maintenance purposes.
7.10.2.10 Level gauge lights shall not be switched by the above-mentioned photo-electric relays
and shall have no maintenance override switches. Level gauge lights should normally be on.
7.10.2.11 Internal lighting of non-process buildings and substations shall be switched inside the
building.
7.10.2.12 Lighting near navigational waters, e.g. jetties and loading platforms, shall not hinder
navigation in any way.
7.10.2.13 The lighting installation in the control rooms shall be designed for switching off,
independently, ceiling lighting groups to suit operators need. The luminaries shall be situated in
such a way that reflection on Video Display Units (VDUs), instrument windows and displays is
avoided.
7.10.2.14 In Zone 1 and 2 hazardous areas, fluorescent luminaries with type of protection Exe
shall be used. Luminaries for level gauge lighting shall be of the fluorescent type, bracket-mounted.
7.10.2.15 High pressure discharge luminaries in hazardous areas shall have type of protection
Exd. An isolating switch shall be included within the fitting to prevent the luminary from being
energized when it is not fully assembled.
7.10.2.16 For standardization reasons the same type of Exd or Exe luminaries should be used in
all plant areas, whether classified Zone 1, Zone 2 or non-hazardous.
7.10.2.17 In hazardous areas classified as zone 0 according to article 4 of standard IPS-M-EL161(1), no lighting fixtures shall be installed.
U
7.10.2.19 In hazardous areas classified as zone 1, the lighting fixtures shall be flameproof Exd type
with a degree of protection IP65. The gas group classification of Exd fixtures shall be at least group
IIB. Where hydrogen or acetylene is present, the gas group classification shall be group IIC. The
maximum surface temperature of Exd fixtures shall be suitable for the appropriate gas in the subject
o
area and shall in no case be more than 200 C which corresponds to T3 according to IEC 60079-0
(Exd IIBT3 or Exd IICT3).
P
118
IPS-E-EL-100(1)
Feb. 2012
7.10.2.20 In hazardous areas classified as zone 2 the lighting fixtures shall be increased safety Exe
according to IEC 60079-7. Lighting fixtures suitable for zone 1 as specified in 5.3.11 can also be
used in zone 2 areas. The lighting fixtures with explosion protection of ExnA or ExnC in accordance
with IEC 60079-15 can be used in zone 2 areas with prior approval of the Engineer. The maximum
surface temperature of Exe and Exn fixtures shall be suitable for the appropriate gas in the subject
o
area and shall in no case be more than 200 C which corresponds to T3 according to IEC 60079 .
7.10.2.21 For standardization purpose, the same type of lighting fixtures selected for zone 2 areas
shall be used in safe areas of industrial plants.
7.10.3 Emergency and escape lighting
7.10.3.1 Fixed emergency lighting shall be installed at strategic points in the installations, including
control rooms, substations, fire stations, first-aid rooms, watchmens offices, the main entrances,
and in all other buildings and areas where required for safety reasons. Location and electrical
arrangement shall be such that danger to personnel in the case of a power failure is prevented, and
escape routes are lit.
7.10.3.2 The emergency lighting system shall consist of a number of standard luminaries of the
normal lighting installation, which shall be fed via circuits having a stand-by supply from an
emergency generator or from a battery with an autonomy time of at least 2 Hr. In remote areas,
where only a few fittings are required, self power emergency may be used.
7.10.3.3 In the case of an emergency generator supply, a number of luminaries in the control room
and the basement of the control room, as well as field auxiliary rooms, shall have a standby supply
from an independent source with battery back-up to avoid complete darkness during start-up time of
the diesel.
7.10.3.4 The number of emergency luminaries as part of the total number of fittings shall be
determined as follows:
- Utility Area
20%
- Process Area
10%
- Administrative Area
5%
- Control Room and Auxiliary Rooms
50%
(Including 10% Connected To DC System)

- Substations, Field Auxiliary Rooms,
30%
Compressor and Generator Buildings
7.10.3.5 The escape luminaries shall generally be part of the emergency luminarys installation, but
the luminaries shall have integral batteries rated to maintain the lighting for at least 30 minutes.
Escape luminaries shall be provided in all buildings so as to lead personnel out of the building along
defined escape routes to defined muster points, which shall also be illuminated.
7.10.4 Street and fence lighting
7.10.4.1 Street and fence lighting shall be fed from lighting distribution boards installed in a
conveniently located plant substation. These lighting distribution boards may either be dedicated to
street and fence lighting, or be one or more sub-sections of a plant lighting distribution board. This
lighting shall also be photo-electric relay controlled and provided with a maintenance override
switch, as for ground level plant lighting.
119
Feb. 2012
IPS-E-EL-100(1)
7.10.4.2 Generally, for street/fence lighting three phase and neutral LV supply shall be used. Each
lighting pole shall include a fuse box as well as a four pole terminating box for looping the feeder
cable. Tee cable joints are not allowed. Adjacent luminaries shall not be supplied from the same
fuse. Fence lighting shall be placed in such a way that the fence as well as the area outside the
fence will be illuminated. Normally fence lighting intensity shall be equivalent to the street lighting
intensity stated in Table 15.
7.10.4.3 For fence lighting, the fixtures with high pressure mercury vapor lamps or high pressure
sodium vapor lamps can be used, as selected by the Engineer. Sodium vapor lamps shall not be
used in areas where fire hazard is envisaged.
7.10.4.4 If special security fence lighting is required, unless otherwise specified, a floodlight
installation shall be designed, based on HP discharge lighting with a minimum illumination of 10 lux
(for CCTV Monitors) at any point in the area between the fence and 5 m outside the fence.
7.10.5 Special lighting

7.10.5.1 General
7.10.5.1 Special lighting, e.g. navigation aids, obstruction warning lights and aircraft navigation
lights, shall be installed in accordance with international and/or national standards. Long-life lamps
or normal lamps at reduced voltage shall be used.
7.10.5.2 The installation shall be supplied from an uninterruptible, maintained source.
Navigational aids for offshore structures shall be in accordance with DEP 33.80.00.30-Gen.
7.10.5.2 Aviation warning lighting

7.10.5.2.1 Aviation warning lights shall consist of a double lamp unit with automatic changeover to
the stand-by lamp upon failure of the operating lamp.
7.10.5.3 Illumination of areas to be observed by means of CCTV (Closed Circuit Television)

monitors
7.10.5.3.1 The lighting installation for areas that require observation by closed circuit television
monitors shall be designed in particular with regard to uniformity of the level of illumination as well
as to the location of the individual luminaries. Direct visibility of light-emitting bodies and/or
reflections from covers of the luminaries shall be checked before commissioning of the plant.
7.10.6 Building lighting

Luminaries in closed buildings which are classified non-hazardous areas, e.g. control rooms and
substations, shall be fluorescent bi-pin, with electronic starter, and industrial pattern. Non-industrial
luminaries may be used in control rooms, offices, etc.
7.10.7 Portable lamps

Portable lamps shall be suitable for 24 or 50 volts AC and shall be fed through double wound
transformers fully isolated from earth. The voltage of portable lamps shall be selected by the
Engineer.
120
Feb. 2012
IPS-E-EL-100(1)
7.10.8 Level of illumination
1) Illumination should generally conform to the requirements of Illumination Engineering Society

(IES). Illumination levels in publications of Illumination Engineering Society for the petroleum,
chemical and petrochemical plants are given in Table 15, according to table 4 of API-540.
2) Illumination from the emergency lighting system should be designed to permit safety of
movement for personnel particularly from elevated platforms etc., in addition to that required at
control positions.
7.10.9 Types of lamps and fittings

1) The use of fluorescent types of lighting is preferred, supplemented if necessary in local areas by
compact fluorescent types or Quartz Halogen where there is a space limitation. Sodium type lamps
are not normally permitted due to fire risk, and their use must be avoided. High pressure mercury
vapor lamps shall be used for external lighting, street lighting, flood lighting and interior lighting
industrial especially high bay workshops.
2) If lamps that are adversely affected by transient voltage disturbances are used in working areas,
they must be adequately interspersed with lamps that are not so affected.
3) In the selection of types of lamps consideration should be given to the likelihood of producing
undesirable color distortion.
4) Type of lamps and fittings should be a minimum.
5) In the selection of lamps and fittings consideration should be given to ensuring maximum lamp
life and the minimum likelihood of internal moisture accumulation (i.e., effects of vibration, operating
temperature and breathing).
6) All exposed lighting fittings should be of weatherproof construction.
7) For characteristics and application of various light sources see Table 16.
7.10.9 Arrangement and accessibility for light sources
7.10.9.1 Control rooms

Lighting should be provided at the front and rear of all control panels and the arrangement should
preclude the likelihood of inconvenience due to failure of a single sub-circuit or phase. Schemes for
front of panel and control desk illumination should be agreed.
7.10.9.2 Plants and General Areas

i) The arrangement of lighting fittings on final sub-circuits should avoid a complete area of darkness
should any one sub-circuit be isolated.
ii) Fittings should, wherever possible, be mounted from structural steelwork installed for other
purposes, except when this may adversely affect the lighting fitting due, for example, to vibration.
Individual poles, etc., provided for the purpose of mounting, fittings must be of adequate strength to
permit access for maintenance as detailed under (iii) below.
iii) Fittings should be located as far as possible to permit safe access from portable ladders.
iv) Floodlights should be mounted when necessary on metal or concrete masts equipped with
permanent access ladders and a platform.
121
IPS-E-EL-100(1)
Feb. 2012
TABLE 15 - ILLUMINANCES LEVELS
MINIMUM
ILLUMINANCE
LUX
AREA OR ACTIVITY
ELEVATION
MILLIMETER
I PROCESS AREAS
A) General process units
Pump rows, valves, manifolds
Heat exchangers
Maintenance platforms
Operating platforms
Cooling towers (equipment areas)
Furnaces
Ladders and stairs (inactive)
Ladders and stairs (active)
Gage glasses
Instruments (on process units)
Compressor houses
Separators
General area
B) Control rooms and houses
Ordinary control house
Instrument panel
Console
Back of panel
Central control house
Instrument
Back of pane
C) Specialty process units
Conveyors
Conveyor transfer points
50
30
10
50
50
30
30
50
50
50
200
50
10
Ground
Ground
Floor
Floor
Ground
Ground
Floor
Floor
Eye level
Eye level
Floor
Top of bay
Ground
300
300
300
100
500
500
100
Floor
1700
760
760
Floor
1700
900
20
50
Surface
Surface
50
150
200
Ground
Floor
1100
200
50
Floor
Ground
5
10
5
Floor
Ground
Floor
50
100
100
Floor
Point
Point
20
20
150
50
50
Ground
Ground
Floor
Floor
1200
4
2
Ground
Ground
Ground
II NONPROCESS AREA
A) Loading, unloading, and cooling water
pump houses, Pump area
General control area
Control panel
B) Boiler and air compressor plants
Indoor
Outdoor equipment 50
C) Tank fields (where lighting is required)
Ladders and stairs
Gating area
Manifold area
D) Loading racks
General area
Tank car
Tank trucks, loading point
E) Tanker dock facilities
F) Electrical substations and switch yards
Outdoor switch yards
General substation (outdoor)
Substation operating aisles
General substation (indoor)
Switch racks
G) Plant road lighting (where lighting is
required)
Frequent use (trucking)
Infrequent use
H) Plant parking lots
I) Aircraft obstruction lighting
122
IPS-E-EL-100(1)
Feb. 2012
III Buildings
A) Offices
500
B) Laboratories
Qualitative, quantitative and physical test
Research, experimental
Pilot plant, process and specialty
Glassware, washrooms
Fume hoods
Stock rooms
500
500
300
300
300
150
900
900
Floor
900
900
Floor
50
5
50
100
200
300
Floor
Ground
760
760
760
1200
200
500
150
300
200
200
300
Floor
760
Floor
760
760
760
760
100
100
Floor
Floor
100
150
50
Floor
Floor
Floor
G) Cafeteria
Eating
Serving area
Food preparation
General, halls, etc.
300
300
300
100
760
900
900
Floor
H) Garage and firehouse

Storage and minor repairs
100
Floor
I) First aid roomed
700
760
C) Warehouses and stock rooms

Indoor bulk storage
Outdoor bulk storage
Large bin storage
Small bin storage
Small parts storage
Counter tops
D) Repair shop
Large fabrication
Bench and machine work
Crane way, aisles
Small machine
Sheet metal
Electrical
Instrument
E) Change housed
Locker room, shower
Lavatory
F) Clock house and entrance gatehouse
Card rack and clock area
Entrance gate, inspection
General
Notes:
a) These illumination values are recommended practice to be considered in the design of
new facilities.
b) Indicates vertical illumination.
c) Refer to port authority for required navigational lights.
d) Luminance may be different from those recommended for other industries because of the
nature of area.
e) Refer to local aviation authority for requirements of obstruction lighting and marking.
123
IPS-E-EL-100(1)
Feb. 2012
TABLE 16 - THE PRINCIPAL LIGHT SOURCES FOR GENERAL LIGHTING PURPOSES AND
THEIR CHARACTERISTICS
Types
Compact Fluorescent (CFLs)
Metal Halide
High Pressure Sodium(HPS)
LEDs (Light-Emitting
Diodes)
These lamps is an electric

discharge device with utilizes a
low pressure a mercury vapor arc
to generate ultra-violet energy.
The ultra-violet energy is obsorbed
a phosphor coat on the inside of
the glass tube and converted by
the phosphor to visible
wavelengths, the wavelengths of
light generated are determined by
the composition of the phosphor.
20-55 lm/W
8000 to 12000 h
Warm White to Cool White 2700K4000K
A metal-halide
lamp is a mercury
vapor with other
compounds
(known as halides)
added to the arc
tube to improve
both color and
luminous efficacy.
Light is produced in a highpressure sodium (HPS) lamp by

an electric discharge through
combined vapors mercury and
sodium radiation dominating the
spectral emission.
LEDs are solid-state

semiconductor devices that
convert electrical energy
directly into light
45-100 lm/W
8000 to 12000 h
Warm White to
White 3000K4200K
commercial office
space,
manufacturing
plants,
warehouses,
sports lighting, and
roadways.
45-110 lm/W
16000 to 20000 h
Warm yellow 2000K
45-80 lm/W
50000h
White to daylight 3500K6000K
Provides general illumination for

outdoor use in residential and
light commercial applications.
Ideal for walkways, large yards,
parking lots, barns and play
areas creating an inviting
exterior space as well as
providing safety and security.
Street lighting, outdoor area

lighting, households, accent
lighting, retrofit lamp
architectural lighting.
Characteristics
Working Principle
Luminous Efficiency
Useful life
Color rendering
Application area
These bulbs are the ideal for your

small lighting fixtures and suitable
for all areas of application.
especially where continous
economical lighting is needed.
Note:
1 Lux 1 candela/m
1 Candela one lumen. per steroidal
7.11 Earthing, Bonding and Lightning Protection
7.11.1 General
Proper earthing is essential to safe and satisfactory performance of a power system and an
industrial plant. There are four requirements for such earthing:
1) Providing a low impedance path for return of fault currents, so that an over current protection
device can act quickly to clear the fault.
2) Maintaining a low potential difference between exposed metal parts to avoid personnel hazards
during normal and fault condition.
3) Protect properties in the event of static charges and transient phenomena (lightning, switching
operation) which may caused fire and explosion.
4) Over voltage control

The objects can be achieved by two kinds of earthing arrangements known as system earthing and
equipment earthing. The former is essential to the security of electrical system and the latter is done
to ensure the safety of human life and equipments.
124
Feb. 2012
IPS-E-EL-100(1)
7.11.2 System earthing
7.11.2.1 General
The regulation that one point of every system shall be earthed is designed primarily to preserve the
security of the system by ensuring that potential on each conductor is restricted to such a value as
is consistent with the level of insulation applied. From the point of view of safety, it is equally
important that earthing should ensure efficient and fast operation of protective gear in the case of
earth faults. The system earth resistance must be such that when any fault occurs against which
earthing is designed to give protection; the protective gear will operate to make the faulty feeder or
equipment harmless. In most cases such operation involves isolation of the faulty feeder or
equipment by circuit breakers or fuses. The common classifications of earthing in this standard are
as follows:
a) Solidly earthed
b) Resistance earthed
7.11.2.2 M.V and H.V system earthing
7.11.2.2.1 M.V and H.V system neutrals shall be earthed TNS at each source of supply.
7.11.2.2.2 M.V and H.V Transformer neutral with secondary voltage less than 36kV shall be
resistance earthed. The rating of each resistor shall be such that to limit the earth fault current
approximately equal to the rated full load current of the transformer secondary.
7.11.2.2.3 In situation where generators are to be directly connected to the main H.V switchboard,
each generator should be earthed via its own earthing resistor. This however, is subject to
verification that the zero sequence, triple harmonic current (3rd, 9th, 15th, etc.) that could circulate
through the resistors under various loading conditions of the generators would not be damaging to
the resistors.
7.11.2.2.4 The rating of each resistor should be such as to limit the magnitude of earth fault current
to the rated full load current or manufacturer recommended value of the generator to which is
connected . These resistors should be solid type and shall be rated to withstand the respective E/F
current for duration of not less than 10 seconds.
Note:
In any case the earthing current shall not exceed 630 A.
7.11.2.2.5 In situations where generators of dissimilar rating characteristics or, Loadings are to be
operated in parallel such as to give rise to circulating currents resulting from triple harmonics then
the system shall be earthed via one earthing resistor only. Each generator shall then be provided
with a suitable switching device to facilitate connection of any machine to the single earthing
resistor.
7.11.2.2.6 For grid in feed system voltages above 36 kV, the neutral point of transformers should
be solidly earthed. In these situations high earth fault current flows in the general mass of earth in
the vicinity of the substation so earthing arrangement must be designed such that these currents do
not results dangerous step and touch potential. Detailed guidance is given in IEEE standard 80.
125
Feb. 2012
IPS-E-EL-100(1)
7.11.2.3 L.V system

7.11.2.3.1 L.V electrical system neutral at each source of supply shall be solidly earthed by means
of dedicated earth electrodes which have a direct, low impedance connection to the plant main
earth grid.
The system of earthing shall be designated TN-S in accordance with IEC 60364-3. For the other
systems of earthing (such as TN-C, TN-C-S & TT) , refer to IEC 60364-3.
7.11.2.3.2 For fixed L.V equipment, each loop impedances shall be such as to effect circuit
disconnection in a time not exceeding 1 s under solid (negligible impedance) earth fault condition.
7.11.2.3.3 The impedance between the earth electrode or earthing terminal and any point on the
earth continuity conductor should not exceed 1 ohm at frequency of the supply.
7.11.3 Earthing grid
7.11.3.1 For the earthing of electrical system, equipment and structures, each installation shall have
one common earth grid connected to at least two groups of earth electrodes. The resistance of this
grid to general mass of earth shall no be less than the value specified by this standard when one
group of electrodes is disconnected for the purpose of measuring or inspection. The earth grid shall
extend throughout the plant in form of a plant ring with branch interconnections to the equipment
and structures to be earthed and shall from part of a single earth grid for whole site.
Note:
Instrument earthing such as intrinsically safe, non-intrinsically shall be considered and
installed as stated in proper instrument IPS.
7.11.4 Equipment earthing

All electrical and non electrical equipment and parts of them which are liable to contact with live
conductor or accumulate dangerous level of static charges shall be in effective contact with earth.
7.11.4.1 Electrical equipments earthing
7.11.4.1.1 A bar of high conductivity hard drawn copper shall be fixed inside the trench or cable
gallery of the substation to which the earth bars of all switchboards and the metallic enclosures of
all low voltage ancillary equipment shall be connected.
7.11.4.1.2 All main switchboards shall be connected to substation earthing system at two separate
points. The tank of each main transformer shall be connected directly to the plant main earth grid.
7.11.4.1.3 The armouring and metallic sheath (if provided) of all multi core cables shall be bonded
to the switchboard earth bar via termination or the gland. Where single core cables are used they
shall be bonded to earth at one end only. The earthed end should be at hazardous end (if any).
7.11.4.1.4 The enclosures of all high and medium voltage motors shall be connected directly to the
plant main earth grid or to local earth electrodes. A common earth electrode may be used for
several motors in the same area.
7.11.4.1.5 The enclosure of low voltage equipments shall be bonded to the plant main earth grid.
126
Feb. 2012
IPS-E-EL-100(1)
7.11.4.2 Non electrical equipments earthing
7.11.4.2.1 Vessels
Two earthing connections shall be taken from the vessel to main plant earthing grid. This is not
necessary done for the vessel which is mounted directly on the steelwork with well conducting to
the earth. Where the vessel is too remote from the plant as to make connection to the main earthing
system impractical, two connections shall be taken from the vessel to separate earth electrodes.
7.11.4.2.2 Storage tanks

Tanks up to 30 m diameter shall be provided with two, and tanks over 30 m diameter shall be
provided with three equally spaced earthing bosses. For group of tanks earth electrodes common to
the group may be installed provided that each tank has, as minimum two paths to earth. This
ensures that during testing of one electrode the tank will remain earthed by system with an earth
resistance less than 10 Ohms.
On floating roof tanks, multiple shunt connections shall be provided between the floating roof and
the tubing shoe at adequate intervals around the roof periphery.
7.11.5 Lightning protection earthing
7.11.5.1 Lightning protection system if required shall be designed and installed in accordance with
IEC 61024 or BS 6651.
7.11.5.2 In order to protect against a direct lightning stroke as a minimum the tallest structure on the
plant shall be directly earthed as close to the base as possible with a minimum of two electrodes
(less than 5 Ohm) and interconnected with main plant earthing grid.
7.11.5.3 Metal structures, e.g. vessels, etc., do not require additional protection beyond the earthing
requirements specified in the equipment earthing.
7.11.5.4 The connection to earth should be as short and straight as possible.
7.11.5.5 Where the plant is located in proximity to the process area substation the lightning earthing
system shall be connected to the power earthing system at two points.
7.11.5.6 In all areas classified as hazardous, steelwork such as stairways, cable racks, handrails,
etc., which is mounted on or attached to non-metallic structures shall be bonded to the general
earthing system either directly or via other earthed metal at intervals not exceeding 30 m.
7.11.5.7 Non-metallic structure less than 9 m in height do not generally require lighting protection.
If greater than 18 m in height, they shall be provided with lightning protection.
7.11.5.8 The need for lightning protection on non-metallic structures between 9 m and 18 m in
height shall be determined taking into account the heights of other adjacent structures, the
nearness of flammables materials, consequences of damage, etc.
7.11.5.9 Metallic guy ropes used for supporting metallic or non-metallic stacks or other structure
shall be bonded at their upper ends to the stack or structure if metallic, or to the lightning protective
system in the case of non-metallic stacks or structures. The lower end of each guy rope shall be
directly earthed.
7.11.5.10 For offshore installations, all plant which is not in metallic contact with earthed structural
steelwork shall be connected to the platform steelwork and no separate lightning earthing system is
required.
127
Feb. 2012
IPS-E-EL-100(1)
7.11.6 Earthing of offshore installation
7.11.6.1 The steel deck and structure of an offshore installation is an inherently very low impedance
structure capable of conducting earth fault currents without giving rise to sparks or dangerous
potential differences. Good electrical continuity is achieved by intimate metal to metal contact
through equipment fixing bolt, clamping, riveting or by welding, such that bonding cables need not
be used between pieces of non-electrical equipment and between equipment earth and the steel
deck.
7.11.6.2 Earthing conductors are required to bond the main components of the generation and
distribution system (namely M.V and L.V generators, transformers, reactors, switchboards, motors
and UPS units) to the platform steelwork. They shall be individually identified, and record on
drawings. The metallic sheath and armour of a submarine cable shall be solidly bonded to the
platform steelwork at both ends of the cable.
7.11.7 Electronic and instrumentation earthing
7.11.7.1 Special attention shall be paid to electronic and instrumentation system earthing, if
required for computer and control system. These equipments shall be separately earthed from the
electrical earth system. This separate earth system called clean earth" or instrument earth or
computer earth (less than 1 Ohm) as relevant, can be one or a number of separate and
independent earth system depending on manufacturers requirement.
7.11.7.2 The clean earth electrode(s) shall be located outside of resistance zone of power earthing
electrode(s) (radius of this zone is generally 15 20 m).
7.11.7.3 The earth conductor between instrument clean earth bar in the auxiliary room and the
clamp type earth bar in the instrument clean earth pit shall be braided or armoured. This braiding or
armoring shall be bonded to the electrical earthing system to shield this earth conductor from
surface stray earth currents which may cause unwanted interference.
7.11.7.4 The instrument clean earth and electrical earthing system shall be inter connected by a
2
single 70 mm earth wire in each field auxiliary room or control room.
7.11.7.5 Where interconnection between instrument clean earth and electrical earthing system may
be subjected the effect of electrical storms, or high voltage induced, the interconnecting lines or
cables shall be equipped with suitable surge diverters to prevent damage to instrument equipment.
7.11.8 Earthing where cathodic protection is applied

7.11.8.1 Bonding between catholically protected equipments and any earthing system can reduce
the efficiency of an impressed current cathodic protection system by diverting the flow of impressed
current.
7.11.8.2 The cathodically protected sections of pipeline shall be isolated from unprotected sections
and from any earthing system.
7.11.8.3 Where plant is catholically protected, either by sacrificial anodes or by an impressed
current system, the design of earthing system shall be agreed with the suppliers and designers of
the cathodic protection system.
7.11.9 Earthing and protective conductor

7.11.9.1 Protective conductor shall be suitably protected against mechanical damage, chemical or
electrochemical deterioration, electrodynamics forces and thermodynamic forces.
128
Feb. 2012
IPS-E-EL-100(1)
7.11.9.2 Buried earthing and protective conductors should normally be bare copper cable or tapes.
However, if there is a likelihood of corrosion PVC sheathed, colored yellow / green type shall be
used.
7.11.9.3 Joints in protective conductors should be avoided.
7.11.9.4 The following metal parts are not permitted for use as protective conductor or as protective
bonding conductors:
- Metallic water pipes
- Pipes containing flammable gases or liquids
- Constructional parts subjected to mechanical stress in normal service
- Flexible metal parts
- Support wires
7.11.9.5 Protective conductors may consist of one or more of following:
a) a conductor in multicore cables
b) insulated or bare conductor in a common enclosure with live conductors
c)fixed installed bare or insulated conductor
d) metallic cable sheath, cable screen, cable armor, wire braid concentric conductor, metallic
conduit subject to the conditions stated in 7.11.9.5 "a" and "b".
7.11.9.6 Where the installation contains equipment having metal enclosures such a low voltage
switchgear and controlgear assemblies or busbar trunking system, the metal enclosures or frames
may be used as protective conductors if they simultaneously satisfy the flowing three requirements:
a) Their electrical continuity shall be assured by construction or by suitable connection so as to
ensure protection against mechanical, chemical or electrochemical deterioration.
b) They comply with the requirement of protective conductor sizing and jointing.
c) They shall permit the connection of other protective conductors at every predetermined tap off
point.
7.11.9.7 Earthing / protective conductor sizing

7.11.9.7.1 The crosssectional areas of protective/earthing conductors shall not be less than the
valve determined as bellow:
1) By the following formula applicable only for disconnection times not exceeding 5 seconds
S=
I 2 .t
K
Where:
2
S: is the cross sectional area, in mm

I: is the value (r.m.s) in ampere of prospective fault current
t: is the operating time of the back up protection device
K: is the factor dependent on the material of the protective conductor, the insulation and
other parts and the initial and the final temperatures. (For calculation of K, see IEC 603645-54 annex A)
2) Specified sizes in tables 17 and 18.
129
Feb. 2012
IPS-E-EL-100(1)
TABLE 17 - CONDUCTOR SIZE FOR BRANCH EARTH CONDUCTORS, CONNECTED TO

INDIVIDUAL SWITCHGEAR AND CONTROL GEAR ASSEMBLIES, MOUNTED IN
SUBSTATIONS, SWITCH ROOMS AND CONTROL ROOMS
Rated short current
and duration
Conductor size
in mm2
20 KA / 1 s
25 KA / 1 s
31.5 KA / 1 s
40 KA / 1 s
50 KA / 1 s
63 KA / 1 s
80 KA / 1 s
270
270
270
270
2120
2120
2150
Note:
2
270 means, 70mm cable connected to two side switchgear and controlgear.
TABLE 18 - MINIMUM EARTHING / PROTECTIVE CONDUCTOR SIZE FOR VARIOUS
APPLICATIONS
APPLICATION
SIZE / mm2
Plant earth main ring
70
Branch to metallic enclosures of H.V & M.V electrical equipment

Branch to metallic enclosures of H.V & M.V electrical equipment , having a supply cable crosssectional area 35 mm2
Branch to metallic enclosures of H.V & M.V electrical equipment , having a supply cable crosssectional area < 35 mm2
Branch to control panels, etc.
70
35
25
25
Branch to non-electrical equipment exposed to lightning , e.g. tanks, columns and tall structures
70
To other non-electrical equipments
25
Interconnection cable between clean earth and electrical earthing system
70
Interconnection cable between lightning earth electrode and structure to be protected
70
Main earth wire for temporary electrical installations
70
Branch earth wire for temporary electrical installations
25
7.11.10 Earth electrodes

7.11.10.1 Effect of shape on electrode resistance with all electrodes the greater part of the fall in
potential occurs in the soil within a meter of the electrode surface, since it is here that the current
density is highest. To obtain a low overall resistance the current density should be as low as
possible in the medium adjacent to the electrode which should be so designed as to cause the
density to decrease rapidly with distance from the electrode this requirement is met by making the
dimensions in one direction large compared with those in the other two thus a pipe, rod or strip has
a lower resistance than a plate of equal surface area.
7.11.10.2 There is different types of earth electrode may be considered, such as:
- Rod
- Plate
- Strip or conductor electrode
- Structural steelwork (for offshore)
7.11.10.3 Material and dimensions of the earth electrodes shall be selected to withstand corrosion
and to have adequate mechanical strength.
7.11.10.4 Earth rods are generally used and available in standard length of at least 1.2 m and can
be extended in length by suitable coupling.
7.11.10.5 In soils of uniform resistivity, it is more economical to install a number of rods connected
in parallel from a single deeply driven rod. In such cases each rod shall be situated outside the
resistance zone of any other. In practice the separation shall not be less than electrode length.
130
Feb. 2012
IPS-E-EL-100(1)
7.11.10.6 Earth strip or conductor electrodes should be used where high resistivity soil underlies
shallow surface layers of low resistivity. They are frequently in form of untinned strip not less than
25 mm by 1.5 mm in section, but may be of bare copper conductor with cross section area not less
2
70 mm . In this case the company engineer approval is needed.
7.11.10.7 If several strip electrodes are required for connection in parallel in order to reduce the
resistance the separation should be made by 2 meters.
7.11.10.8 The depth of strip embedding from the ground surface shall not be less than 50 cm.
7.11.10.9 Employing of structural steelwork as an earth electrode shall be limited in offshore
installations.
7.11.10.10 Plates are not generally recommended because of used in small numbers, they least
reliable type of made electrode. However may be suited in very rocky or coralloid land in which an
earth well may be required.
7.11.10.11 Where the resistance of a single plate is higher than the required value, two or more
plates may be used in parallel, provided that each plate is installed outside the resistance area of
any other. This separation shall not be less than 2m.
7.11.10.12 Where each plates are used either copper type or cost iron type the thickness, shall not
be less than 3mm and 12mm receptivity and the size employed shall not be greater than 1.2m by
1.2m.
7.11.10.13 The depth at which plates are set shall be such as to ensure that the surrounding soil is
always damp.
7.11.10.14 each earth electrode shall be terminated in a suitable pit for inspection and measuring
purposes.
7.11.10.15 where a group of electrodes are used at least one more than the required minimum
number of electrodes shall be installed. By this means, each electrode can be disconnected one at
the time for testing without affecting the integrity of the power earthing system.
7.11.11 Soil resistivity
7.11.11.1 The resistance to earth of an electrode of given dimensions is dependent on the electrical
resistivity of the soil in which it is installed. Soil resistivity is varied according to the type of soil,
moisture content, degree of compaction, chemical composition and soil temperature. The latest
factor is only important near and below freezing point. The type of soil largely determines its
resistivity. Typical values of soil resistivities are given in table 19 for preliminarily.
7.11.11.2 Soil resistivity measurements shall be made at the proposed electrode locations. These
measurements and earthing system design should be carried out at an early stage of the project so
that the electrode locations are compatible with plot plant.
7.11.11.3 Where there is any option, a site should be chosen for the electrodes which are not
naturally well drained. Locations where the ground is kept moist by water flowing over it shall be
avoided. Wherever possible, dry sandy or rocky ground should also be avoided.
7.11.11.4 The effect of possible seasonal increases in electrode resistance due to drying out or
freezing of ground shall be taken into account. Wherever possible, the each electrode should be
installed deep enough to reach the water table or permanent moisture level, deeper than frost is
likely to penetrate and to reach stable ground conditions. For more information refer to IEEE 80 and
ISIRI 4123.
7.11.11.5 Soil resistivity may be reduce 15-90% by chemical treatment, depending upon the kind
and texture of the soil. There are several chemicals suitable for this purpose, including sodium
carbonate, magnesium and copper sulfate, calcium chloride and common salt (addition of less than
one part by weight of salt to 200 of soil moisture has been found to reduce the resistivity by 80
percent).
7.11.11.6 Before chemical treatment is applied to soil, it should be verified that no deleterious effect
on the electrode material will result.
131
Feb. 2012
IPS-E-EL-100(1)
TABLE 19 GENERAL DATA ON EARTH RESISTIVITY

Climatic condition
Type of soil
Alluvium and
lighter clays
A
Normal and high
rainfall (e.g. greater
than 500 mm a year)
C
Underground
waters
(saline)
Probable
value
Range of
Values
encountered
Range of
Values
encountered
Range of
Values
encountered
Ohm cm
Ohm cm
Ohm cm
Ohm cm
500
100 to 500
1 000
500 to
1 000 to
2000
10 000
1 000 to
5 000 to
3 000
30 000
Clays
(excluding
alluvium)
2 000
Marls (e.g.
keuper marl )
B
Low rainfall and desert
conditions (e.g. less than 250
mm a year )
5 000
3 000 to
10 000
Porous
limestone (e.g.
chalk )
10 000
300 to 1 000
1 000 to 3 000
3 000 to
30 000
30 000
Porous
sandstone
(e.g. Keuper
100 000
100 000
Sandstone
and clay
shales )
Quartzite,
compact and
crystalline
limestone (e.g.
carboniferous,
marble, etc.)
10 000 to
30 000 to
300 000
100 000
3 000 to
upwards
10 000
100 000
200 000
100 000
up wards
Clay slates
and slatey
shales
Granite
Fissile slates,
Schists Gneiss
and Igneous
rocks
* Depends on water level in locality
132
IPS-E-EL-100(1)
Feb. 2012
7.11.11.7 Earthing system resistance value, the resistance required varies inversely with fault
current to earth. A suitably low resistance is necessary under all climatic conditions, depending on
the system voltage and fault current level. The resistance and hence possible rise in potential
between the main earth system and general mass of earth should be as low as can economically be
contrived. However the resistance value for different earth system is specified in table 20 and shall
be considered.
TABLE 20 EARTH RESISTANCE VALUE FOR DIFFERENT EARTHING SYSTEM
APPLICATION
EARTHING SYSTEM
RESISTANCE
VALUE
In
M.V & H.V Substation
<1
M.V Power generation
<1
L.V Distribution system
<2
Plant Main earth grid
<4
Main earth grid
<1
Domestic *
<5
Lightning protection system
<5
Clean earth for instrumentation , control

computer , and communication system
<1
* On condition that suitable earthing protective devices RCPD (Residual Current Protection Device)
/ RCD (Residual Current Device) have been used.
133
Feb. 2012
APPENDICES
APPENDIX A
DOCUMENT LIST
134
IPS-E-EL-100(1)
Feb. 2012
135
IPS-E-EL-100(1)
Feb. 2012
136
IPS-E-EL-100(1)

Engineering Standard: IPS-E-EL-100

Uploaded by

Copyright:

Available Formats

Engineering Standard: IPS-E-EL-100

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Engineering Standard: IPS-E-EL-100

Uploaded by

Copyright:

Available Formats

IPS-E-EL-100(1)

Standards and Research department

VENDOR AND SUPPLIER:

(IRANIAN PETROLEUM STANDARDS)

Construction Standard for Electrical Installation

Material and Equipment Standard for Low Voltage Induction Motors

Material and Equipment Standard for Medium and High Voltage

Engineering Standard for Hazardous Area

Materials and Equipment Standard for Synchronous Generators

Engineering Standard for Overhead Transmission & Distribution

Procedure for Initial & Periodical Inspection in Potentially Explosive

Material and Equipment Standard for Rotating Electrical Machines

Material and Equipment Standard for Synchronous Generators

Inspection Standard for Pre-commissioning Electrical Tests

Material and Equipment Standard for Low Voltage Switchgear and

Material and Equipment Standard for Medium and High Voltage

Material and Equipment Standard for Power Factor Improvement

Dry Type Power Transformers

Oil Immersed Power Transformers

Material Standard for Electrical Heat Tracing

Material and Equipment Standard for Low Voltage Industrial and

Material and Equipment Standard for Current Limiting Reactors

Material and Equipment Standard for Battery and Battery Charger

Material and Equipment Standard for Uninterruptible Power Supply

Material and Equipment Standard for Low Voltage Industrial and

Material Standard for Low Voltage Cables & Wires

Material Standard for Medium and High Voltage Power Cables

(INTERNATIONAL ORGANIZATION FOR STANDARDIZATION)

Code of practice for Ventilation in Petrochemical Plants and

NFPA (NATIONAL FIRE PROTECTION ASSOCIATION)

Fire Protection for Telecommunication facilities

Electrical Safety Requirements for Employee Workplaces

ASHRAE (AMERICAN SOCIETY OF HEATING, REFRIGERATING AND AIR-CONDITIONING

Ventilation for Acceptable Indoor Air Quality

(BRITISH STANDARDS INSTITUTION)

Safety requirements for Secondary Batteries and Battery Installations

IEEE (INSTITUTE OF ELECTRICAL AND ELECTRONICS ENGINEERS)

Autonomy time (of a battery)

Electrical power system

Low voltage (LV)

Point of common coupling (PCC)

Uninterruptible power supply

Zone 0 (in the classification of hazardous gas areas)

Zone 1 (in the classification of hazardous gas areas)

Zone 2 (in the classification of hazardous gas areas)

Zone 21 (in the classification of hazardous dust areas)

Zone 22 (in the classification of hazardous dust areas)

Bus coupler circuit breaker

Bus section circuit breaker (= switched busbar circuit breaker)

Power plant substation/switchboard

Power station (power plant)

Remote control unit (RCU)

Substation (of a power system)

Variable speed drive system (VSDS)

5.2 Operational Safety and Reliability

5.3 Certificates, Declarations and Test Reports

5.4 Quality Assurance and Control

5.5 Standards, Codes and Regulations