INTRODUCTION

Shear walls are vertical elements of the horizontal force resisting system. Shear
walls are constructed to counter the effects of lateral load acting on a structure. In
residential construction, shear walls are straight external walls that typically form a box
which provides all of the lateral support for the building.When shear walls are designed
and constructed properly, and they will have the strength and stiffness to resist the
horizontal forces.
In building construction, a rigid vertical diaphragm capable of transferring lateral
forces from exterior walls, floors, and roofs to the ground foundation in a direction
parallel to their planes. Examples are the reinforced-concrete wall or vertical truss.
Lateral forces caused by wind, earthquake, and uneven settlement loads, in addition to the
weight of structure and occupants; create powerful twisting (torsion) forces. These forces
can literally tear (shear) a building apart. Reinforcing a frame by attaching or placing a
rigid wall inside it maintains the shape of the frame and prevents rotation at the joints.
Shear walls are especially important in high-rise buildings subjected to lateral wind and
seismic forces.
In the last two decades, shear walls became an important part of mid and highrise residential buildings. As part of an earthquake resistant building design, these walls
are placed in building plans reducing lateral displacements under earthquake loads. So
shear-wall frame structures are obtained.
Shear wall buildings are usually regular in plan and in elevation. However, in
some buildings, lower floors are used for commercial purposes and the buildings are
characterized with larger plan dimensions at those floors. In other cases, there are
setbacks at higher floor levels. Shear wall buildings are commonly used for residential
purposes and can house from 100 to 500 inhabitants per building

SeminarsTopics.com

PURPOSE OF CONSTRUCTING SHEAR WALLS

Shear walls are not only designed to resist gravity / vertical loads (due to its selfweight and other living / moving loads), but they are also designed for lateral loads of
earthquakes / wind. The walls are structurally integrated with roofs / floors (diaphragms)
and other lateral walls running across at right angles, thereby giving the three
dimensional stability for the building structures.
Shear wall structural systems are more stable. Because, their supporting area
(total cross-sectional area of all shear walls) with reference to total plans area of building,
is comparatively more, unlike in the case of RCC framed structures.
Walls have to resist the uplift forces caused by the pull of the wind. Walls have to
resist the shear forces that try to push the walls over. Walls have to resist the lateral force
of the wind that tries to push the walls in and pull them away from the building.

COMPARISONS OF SHEAR WALL WITH CONSTRUCTION OF

CONVENTIONAL LOAD BEARING WALLS
Load bearing masonry is very brittle material. Due to different kinds of stresses
such as shear, tension, torsion, etc., caused by the earthquakes, the conventional
unreinforced brick masonry collapses instantly during the unpredictable and sudden
earthquakes.
The RCC framed structures are slender, when compared to shear wall concept of
box like three-dimensional structures. Though it is possible to design the earthquake
resistant RCC frame, it requires extraordinary skills at design, detailing and construction
levels, which cannot be anticipated in all types of construction projects.
On the other hand even moderately designed shear wall structures not only more
stable, but also comparatively quite ductile. In safety terms it means that, during very
severe earthquakes they will not suddenly collapse causing death of people. They give

SeminarsTopics.com

enough indicative warnings such as widening structural cracks, yielding rods, etc.,
offering most precious moments for people to run out off structures, before they totally
collapse.
For structural purposes we consider the exterior walls as the shear-resisting walls.
Forces from the ceiling and roof diaphragms make their way to the outside along
assumed paths, enter the walls, and exit at the foundation.

FORCES ON SHEAR WALL

Shear walls resist two types of forces: shear forces and uplift forces. Shear
forces are generated in stationary buildings by accelerations resulting from ground
movement and by external forces like wind and waves. This action creates shear
forces throughout the height of the wall between the top and bottom
shear wall connections.
Uplift forces exist on shear walls because the horizontal forces are applied to the
top of the wall. These uplift forces try to lift up one end of the wall and push the other
end down. In some cases, the uplift force is large enough to tip the wall over. Uplift
forces are greater on tall short walls and less on low long walls. Bearing walls have less
uplift than non-bearing walls because gravity loads on shear walls help them resist uplift.
Shear walls need hold down devices at each end when the gravity loads cannot resist all
of the uplift. The hold down device then provides the necessary uplift resistance.

SeminarsTopics.com

FUNCTIONS OF SHEAR WALL

Shear walls must provide the necessary lateral strength to resist horizontal
earthquake forces. When shear walls are strong enough, they will transfer these
horizontal forces to the next element in the load path below them. These other
components in the load path may be other shear walls, floors, foundation walls, slabs or
footings.
Shear walls also provide lateral stiffness to prevent the roof or floor above from
excessive side-sway. When shear walls are stiff enough, they will prevent floor and roof
framing members from moving off their supports. Also, buildings that are sufficiently
stiff will usually suffer less nonstructural damage.

SeminarsTopics.com

LOCATION OF SHEAR WALLS

Shear walls should be located on each level of the structure including the crawl
space. To form an effective box structure, equal length shear walls should be placed
symmetrically on all four exterior walls of the building. Shear walls should be added to
the building interior when the exterior walls cannot provide sufficient strength and
stiffness.
Shear walls are most efficient when they are aligned vertically and are supported
on foundation walls or footings. When exterior shear walls do not provide sufficient
strength, other parts of the building will need additional strengthening. Consider the
SeminarsTopics.com

common case of an interior wall supported by a sub floor over a crawl space and there is
no continuous footing beneath the wall. For this wall to be used as shear wall, the sub
floor and its connections will have to be strengthened near the wall. For Retrofit work,
existing floor construction is not easily changed. Thats the reason why most retrofit work
uses walls with continuous footings underneath them as shear walls.

CLASSIFICATION OF SHEAR WALLS

Simple rectangular types and flanged walls (bar bell type)

Coupled shear walls
Rigid frame shear walls
Framed walls with in filled frames
Column supported shear walls
Core type shear walls

Fig. Showing Classification Of Shear Wall

SeminarsTopics.com

METHODS OF DESIGN OF SHEAR WALL

There are three types of design methods
Segmented shear wall method
Force transfer ground openings method
Perforated shear wall method
The segmented shear wall method uses full height shear wall segments that comply
with ratio requirements and are usually restrained against overturning by hold down
devices at the ends of each segment.
The second method force transfer-ground openings method consider the entire shear
wall with openings and the wall piers adjacent to openings are segments. The method
requires the forces around the perimeter of the openings to be analyzed, designed, and
detailed. With this method, the hold-down devices generally occur at the ends of the shear
wall, not at each wall pier, and special reinforcement around the opening is often
required.

The third and newest method is the perforated shear wall method which is an
empirical approach that does not require special detailing for force transfer adjacent to
the openings. The perforated shear wall method, however, specifically requires holddown devices at each end of the perforated shear wall.

SeminarsTopics.com

TYPES OF SHEAR WALLS

RC Shear Wall
Plywood Shear Wall
Midply Shear Wall
RC Hollow Concrete Block Masonry Wall
Steel Plate Shear Wall

RC SHEAR WALL
It consists of reinforced concrete walls and reinforced concrete slabs. Wall
thickness varies from 140 mm to 500 mm, depending on the number of stories, building
age, and thermal insulation requirements. In general, these walls are continuous
throughout the building height; however, some walls are discontinued at the street front
or basement level to allow for commercial or parking spaces. Usually the wall layout is
symmetrical with respect to at least one axis of symmetry in the plan.

Floor slabs are either cast-in-situ flat slabs or less often, precast hollow-core slabs.
Buildings are supported by concrete strip or mat foundations; the latter type is common
for buildings with basements. Structural modifications are not very common in this type
of construction.
SeminarsTopics.com

Reinforcement requirements are based on building code requirements specific for

each country. In general, the wall reinforcement consists of two layers of distributed
reinforcement (horizontal and vertical) throughout the wall length. In addition, vertical
reinforcement bars are provided close to the door and window openings, as well as at the
wall end zones (also known as boundary elements or barbells).

SeminarsTopics.com

PLYWOOD SHEAR WALL

Plywood is the traditional material used in the construction of Shear Walls. The creation
of pre-fabricated shear panels have made it possible to inject strong shear assemblies into
small walls that fall at either side of a opening in a shear wall. As well as the use of a
sheet steel, and steel-backed shear panel (i.e. Sure-Board) in the place of structural use
plywood in shear walls, has proved to be far stronger in seismic resistance when used in
shear wall assemblies.
Plywood shear walls consist of:
Plywood, to transfer shear forces
Chords, to resist tension/compression generated by the over turning moments
Base connections to transfer shear to foundations.

SeminarsTopics.com

10

MIDPLY SHEAR WALL

The MIDPLY shear wall is an improved timber shear wall that was developed by
redesigning the joints between sheathing and framing members, so that the failure modes
observed in standard wall testing are virtually eliminated at lateral load levels high
enough to cause failures in standard walls.
In MIDPLY shear wall design, one ply of sheathing material is placed at the center of
the wall between a series of pairs of studs oriented in a 90 rotated position relative to those
in standard shear walls

SeminarsTopics.com

11

RC HOLLOW CONCRETE BLOCK MASONRY WALLS

RHCBM walls are constructed by reinforcing the hollow concrete block masonry,
by taking advantage of hollow spaces and shapes of the hollow blocks. It requires
continuous steel rods (reinforcement) both in the vertical and horizontal directions at
structurally critical locations of the wall panels, packed with the fresh grout concrete in
the hollow spaces of masonry blocks.

SeminarsTopics.com

12

Reinforced Hollow Concrete Block Masonry (RHCBM) elements are designed

both as load bearing walls for gravity loads and also as shear walls for lateral seismic
loads, to safely with stand earthquakes. This structural system of construction is known as
shear wall diaphragm concept, which gives three-dimensional structural integrity for
the buildings.

STEEL PLATE SHEAR WALL

In general, steel plate shear wall system consists of a steel plate wall, boundary
columns and horizontal floor beams. Together, the steel plate wall and boundary columns
act as a vertical plate girder. The columns act as flanges of the vertical plate girder and
the steel plate wall acts as its web. The horizontal floor beams act, more-or-less, as
transverse stiffeners in a plate girder.

SeminarsTopics.com

13

Steel plate shear wall systems have been used in recent years in highly seismic
areas to resist lateral loads. Figure shows two basic types of steel shear walls; unstiffened
and stiffened with or without openings.

Advantages of Steel Plate Shear Wall to Resist Lateral Loads:

1. The system, designed and detailed properly is very ductile and has relatively large
energy dissipation capability. As a result, steel shear walls can be very efficient and
economical lateral load resisting systems.
2. The steel shear wall system has relatively high initial stiffness, thus very effective in
limiting the drift.
3. Compared to reinforced concrete shear walls, the steel shear wall is much lighter which
can result in less weight to be carried by the columns and foundations as well as less
seismic load due to reduced mass of the structure.

SeminarsTopics.com

14

4. By using shop-welded, field-bolted steel shear walls, one can speed-up the erection
process and reduce the cost of construction, field inspection and quality control resulting
in making these systems even more efficient.
5. Due to relatively small thickness of steel plate shear walls compared to reinforced
concrete shear walls, from architectural point of view, steel plate shear walls occupy
much less space than the equivalent reinforced concrete shear walls. In high-rises, if
reinforced concrete shear walls are used, the walls in lower floors become very thick and
occupy large area of the floor plan.
6. Compared to reinforced concrete shear walls, steel plate shear walls can be much
easier and faster to construct when they are used in seismic retrofit of existing building.
7. Steel plate shear wall systems that can be constructed with shop welded-field bolted
elements can make the steel plate shear walls more efficient than the traditional systems.
These systems can also be very practical and efficient for cold regions where concrete
construction may not be economical under very low temperatures.

SeminarsTopics.com

15

ARCHITECTURAL ASPECTS OF SHEAR WALLS

Most RC buildings with shear walls also have columns; these columns primarily
carry gravity loads (i.e., those due to self-weight and contents of building). Shear walls
provide large strength and stiffness to buildings in the direction of their orientation,
which significantly reduces lateral sway of the building and thereby reduces damage to
structure and its contents.
Since shear walls carry large horizontal earthquake forces, the overturning effects
on them are large. Thus, design of their foundations requires special attention. Shear
walls should be provided along preferably both length and width. However, if they are
provided along only one direction, a proper grid of beams and columns in the vertical
plane (called a moment-resistant frame) must be provided along the other direction to
resist strong earthquake effects.
Door or window openings can be provided in shear walls, but their size must be
small to ensure least interruption to force flow through walls. Moreover, openings should
be symmetrically located. Special design checks are required to ensure that the net crosssectional area of a wall at an opening is sufficient to carry the horizontal earthquake
force.
Shear walls in buildings must be symmetrically located in plan to reduce ill
effects of twist in buildings. They could be placed symmetrically along one or both
directions in plan. Shear walls are more effective when located along exterior perimeter
of the building such a layout increases resistance of the building to twisting.

SeminarsTopics.com

16

ADVANTAGES OF SHEAR WALLS IN BUILDINGS

Properly designed and detailed buildings with shear walls have shown very good
performance in past earthquakes. Shear walls in high seismic regions require special
detailing. However, in past earthquakes, even buildings with sufficient amount of walls
that were not specially detailed for seismic performance (but had enough well-distributed
reinforcement) were saved from collapse. Shear wall buildings are a popular choice in
many earthquake prone countries, like Chile, New Zealand and USA.
Shear walls are easy to construct, because reinforcement detailing of walls is
relatively straight forward and therefore easily implemented at site.
Shear walls are efficient, both interims of construction cost and effectiveness in
minimizing earthquake damage in structural and nonstructural elements like glass
windows and building contents.

SeminarsTopics.com

17

CONCLUSION
Thus shear walls are one of the most effective building elements in resisting
lateral forces during earthquake. By constructing shear walls damages due to effect of
lateral forces due to earthquake and high winds can be minimized. Shear walls
construction will provide larger stiffness to the buildings there by reducing the damage to
structure and its contents.

SeminarsTopics.com

18

REFERENCES

Definition of shear wall- http://www.wisegeek.com/what-is-a-shear-wall.htm

Typical shear wall features, uplift in shear wall, location of shear wallhttp://www.abag.ca.gov/bayarea/eqmaps/fixit/ch3/sld002.htm,
http://www.abag.ca.gov/bayarea/eqmaps/fixit/ch3/sld008.htm

Concrete shear wall construction, http://worldhousing.net/uploads/concrete_shear_wall.pdf?pr=Array

Segmented shear wall designhttp://timber.ce.wsu.edu/Supplements/ShearWall/ShearTable.htm

Wood framed shear wall construction, www.shearwalls.com

Steel plate shear wall

SeminarsTopics.com

19